Astraada AS47CN21 User manual

Add to My manuals
120 Pages

advertisement

Astraada AS47CN21 User manual | Manualzz

ARCHMI-8XX Series

User Manual

Release Date Revision

Mar. 2015 V1.0

®2015 Aplex Technology, Inc. All Rights Reserved. Published in Taiwan

Aplex Technology, Inc.

15F-1, No.186, Jian Yi Road, Zhonghe District, New Taipei City 235, Taiwan

Tel: 886-2-82262881 Fax: 886-2-82262883 E-mail:

[email protected]

URL:

www.aplex.com.tw

Reversion

1.0

Revision History

Date

2015/03/03

Description

Official Version

ARCHMI-8XX Series User Manual

1

Warning!________________________

This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, it may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.

Electric Shock Hazard – Do not operate the machine with its back cover removed.

There are dangerous high voltages inside.

Avertissement!___________________

Cet équipement génère, utilise et peut émettre une énergie de radiofréquence et s'il n'est pas installé et utilisé conformément au manuel d'instructions, il peut provoquer des interférences dans les communications radio. Il a été testé et approuvé conforme aux limites pour un dispositif de classe

A et selon les règles de la FCC, qui sont conçues pour fournir une protection raisonnable contre de telles interférences dans un environnement commercial. Le fonctionnement de cet équipement dans une zone résidentielle est susceptible de provoquer des interférences, dans ce cas l'utilisateur, à ses propres frais, devra faire le nécessaire pour prendre toutes les mesures requises pour corriger le problème.

Risque de choc électrique - Ne pas faire fonctionner la machine avec son capot arrière enlevé. Des tensions dangereuses sont élevées à l'intérieur.

ARCHMI-8XX Series User Manual

2

Caution

Risk of explosion if the battery is replaced with an incorrect type.

Batteries should be recycled where possible. Disposal of used batteries must be in accordance with local environmental regulations.

Precaution

Risque d'explosion si la pile usagée est remplacée par une pile de type incorrect.

Les piles usagée doivent être recyclées dans la mesure du possible. La mise au rebut des piles usagées doit resecter les réglementations locales en vigueur en matière de protection de l'environnement.

Disclaimer

This information in this document is subject to change without notice. In no event shall Aplex Technology Inc. be liable for damages of any kind, whether incidental or consequential, arising from either the use or misuse of information in this document or in any related materials.

ARCHMI-8XX Series User Manual

3

Packing List

Accessories (as ticked) included in this package are:

□ Adaptor

□ Driver & manual CD disc

□ Other.___________________(please specify)

ARCHMI-8XX Series User Manual

4

Safety Precautions

Follow the messages below to prevent your systems from damage:

◆ Avoid your system from static electricity on all occasions.

◆ Prevent electric shock. Don‘t touch any components of this card when the card is power-on. Always disconnect power when the system is not in use.

◆ Disconnect power when you change any hardware devices. For instance, when you connect a jumper or install any cards, a surge of power may damage the electronic components or the whole system.

Consignes de sécurité

Suivez les messages ci-dessous pour éviter que vos systèmes contre les dommages:

◆ Éviter votre système contre l'électricité statique sur toutes les occasions.

◆ Évitez les chocs électriques. Ne pas toucher les composants de cette carte lorsque la carte est sous tension. Toujours débrancher lorsque le système n'est pas en cours d'utilisation.

◆ Couper l'alimentation électrique lorsque vous changez tous les périphériques matériels. Par exemple, lorsque vous connectez un cavalier ou d'installer des cartes, une forte augmentation de la puissance peut endommager les composants électroniques ou l'ensemble du système.

ARCHMI-8XX Series User Manual

5

Table of Contents

Revision History…………………………………………………………………………………………………….1

Warning!/Avertissement!......................................................…………………………….…2

Caution/Precaution/Disclaimer……..………………………………………………………………………3

Packing List…………………………………….……………………………………………………………………..4

Safety Precautions/Consignes de sécurité………………………………….…..……………………..5

Chapter 1 Getting Started

1.1 Features………………………..………………………...…………………………..8

1.2 Specifications…………………...………………………………………………….8

1.3 Dimensions………………………....…………………………………………….11

1.4 Brief Description of ARCHMI-8XX…..….………………………….……16

1.5 Installation of HDD – 7”/8”…………..…………...…………………..…..21

1.6 Installation of HDD – 10.1”/15.6”/18.5”………………………………23

1.7 Installation of HDD – 12.1”/15”/17”/21.5”………………….……….24

Chapter 2 Hardware

2.1 Mainboard Introduction……………………...…………………………....26

2.2 Specifications…………………………..…………………………………………26

2.3 Jumpers and Connectors Location……………………………………...30

2.4 Jumpers Setting and Connectors…………………………………..……31

Chapter 3 BIOS Setup

3.1 Operations after POST Screen…...…….……...…………………………60

3.2 BIOS Setup Utility……………………………………………………………….60

3.3 Main Settings……………………………………..………………………………61

3.4 Advanced Settings……………………………………………………………...62

3.5 Chipset Settings……………………………………….………………………...69

3.6 Security Settings…………………………………………….…………………..71

3.7 Boot Settings…..………………………………………….……………………..72

3.8 Save & Exit Settings……………………………………..…………………....73

Chapter 4 Installation of Drivers

4.1 Intel (R) AtomTM SoC Chipset ………..……...………….………………76

4.2 Intel (R) VGA Chipset……………………………………………….……......79

4.3 Intel (R) LAN Driver………..………………………………………..………...83

ARCHMI-8XX Series User Manual

6

4.4 Realtek ALC662 HD Audio Driver Installation………………………86

4.5 USB 3.0 Driver…………………………………………………………………….87

Chapter 5 Touch Screen Installation

5.1 Windows XP/2003/Vista/WIN7 Universal Driver Installation for

PenMount 6000 Series...……………….…………………………………...91

5.2 Software Functions…………………………………………………………..101

Figures

Figure 1.1: Dimensions of ARCHMI-807………………………………......11

Figure 1.2: Dimensions of ARCHMI-808…………………………………...11

Figure 1.3: Dimensions of ARCHMI-810……………………………………12

Figure 1.4: Dimensions of ARCHMI-812……………………………………12

Figure 1.5: Dimensions of ARCHMI-815……………………………………13

Figure 1.6: Dimensions of ARCHMI-816……………………………………13

Figure 1.7: Dimensions of ARCHMI-817……………………………………14

Figure 1.8: Dimensions of ARCHMI-818……………………………………14

Figure 1.9: Dimensions of ARCHMI-821……………………………………15

Figure 1.10: Front View of ARCHMI-8XX Series…………………………16

Figure 1.11: Rear View of ARCHMI-807/808………………………………17

Figure 1.12: Rear View of ARCHMI-810…………………………………….17

Figure 1.13: Rear View of ARCHMI-812…………………………………….18

Figure 1.14: Rear View of ARCHMI-815…………………………………….18

Figure 1.15: Rear View of ARCHMI-816…………………………………….19

Figure 1.16: Rear View of ARCHMI-817…………………………………….19

Figure 1.17: Rear View of ARCHMI-818…………………………………….20

Figure 1.18: Rear View of ARCHMI-821…………………………………...20

Figure 2.1: Mainboard Dimensions……………………………………….….29

Figure 2.2: Jumpers and Connectors Location-Board Top………….30

Figure 2.3: Jumpers and Connectors Location-Board Bottom……30

ARCHMI-8XX Series User Manual

7

Chapter 1 Getting Started

1.1 Features

 7”/8”/10.1”/12.1”/15”/15.6”/17”/18.5”/21.5” Industrial Compact Size Panel PC

 Flat front panel touch screen

 Fanless design

 Intel Bay Trail N2930(1.83GHz) CPU built-in/E3845(1.91GHz) for option

 Onboard 2GB DDR 3L 1600 MHz/4GB(option)

 9~36VDC wide-ranging power input

 IP65 compliant front panel

 Optional projected capacitive touchscreen support 7H anti-scratch surface

1.2 Specifications

System

CPU

Chipset

Memory

IO Port

USB

ARCHMI-8XX Series

Onboard Intel Bay Trail N2930(1.83GHz )/E3845(1.91GHz) for option

SoC

Onboard 2GB DDR 3L 1600 MHz/4GB(option)

Serial/Parallel

Audio

LAN

Power

Option

(Not available for

ARCHMI-807 and

ARCHMI-808)

1 x USB 2.0 type A

1 x USB 3.0 type A

1 x RS-232 DB-9(COM2)

1 x DB-9 RS-232/422/485 (Default RS-232)(COM1)

1 x Audio Line Out

2 x GbE LAN RJ-45

1 x 3-pin DC Power input terminal

1 x 2-pin connector for power on/off button

2 x RS-232 DB-9 + 1 x Mini-PCIe slot via TB-528C2ME1

2 x CAN bus via TB-528CAN2

2 x USB 2.0 type A Via TB-528U2

2 x USB 2.0 type A + 1 x Mini-PCIe slot + 1xRS-232 DB-9 via TB-528C1U2P1

(TB-528C1U2 for ARCHMI-810)

ARCHMI-8XX Series User Manual

8

Storage Space

Storage 1 x SD card slot, up to 32GB

1 x 1.8” SATA SSD bay, up to 64GB (Easy Accessible) (for 7”/8”)

1 x 2.5" SATA HDD bay for SATA HDD (Easy Accessible)

Expansion

Expansion Slot 1 x Internal Mini-PCIe slot full size

Touch Screen – Resistive Touch Window Type

TS Control IC

Interface

Light

Transmission(%)

PenMount 6000 on Board

USB

Over 80%

Touch Screen – Projected Capacitive Type

TS Control IC Chip on tail

USB

Over 90%

Interface

Light

Transmission(%)

Power

Power Input

Mechanical

Construction

IP Rating

Environmental

Operating temperature(°C)

Storage temperature(°C)

Storage humidity

Certification

Operating System Support

9~36V/DC

RAL 9007

IP65 compliant front panel

0~50℃

-20~60℃

10 to 90% @ 40°C, non- condensing

CE / FCC Class A

OS Support Windows Embedded Compact 7, Windows 7, Windows Embedded Standard

7, Windows 8, Windows Embedded 8 Standard, Windows 8.1

Windows Embedded 8.1 Industry

ARCHMI-8XX Series User Manual

9

Display

Display Type

Max. Resolution

Max. Color

Luminance(cd/m²)

ARCHMI-807(P) ARCHMI-808(P) ARCHMI-810(P) ARCHMI-812(P) ARCHMI-815(P)

7” TFT LCD

800 x 480

262K

350

8” TFT LCD 10.1” TFT LCD 12.1” TFT LCD 15” TFT LCD

800 x 600 1280 x 800 800 x 600 1024 x 768

16.2M

350

16.2M

350

16.2M

450

16.2M

300

Contrast Ratio

Viewing angle

Backlight Lifetime

Mounting

400 : 1 500 : 1 800 : 1 800 : 1 800 : 1

140(H)/110(V) 140(H)/125(V) 160(H)/160(V) 160(H)/140(V) 170(H)/170(V)

40,000 hrs 40,000 hrs

VESA Mount 75 x 75

50,000 hrs 50,000 hrs

VESA Mount 100 x 100

50,000 hrs

Dimensions(mm) 202 x 149 x 40 231 x 176 x 50 285 x 189 x 49 319 x 243 x 52 410 x 310 x 55

Display

Display Type

ARCHMI-816(P) ARCHMI-817(P) ARCHMI-818(P) ARCHMI-821(P)

Max. Resolution

Max. Color

Luminance (cd/m²)

Contrast Ratio

15.6” TFT LCD

1366 x 768

16.7M

300

500 : 1

17” TFT LCD

1280 x 1024

16.7M

350

1000 : 1

18.5” TFT LCD

1366 x 768

16.7M

300

1000 : 1

21.5” TFT LCD

1920 x 1080

16.7M

250

3000 : 1

Viewing angle

Backlight Lifetime

160 (H)/ 160 (V) 170 (H)/ 160 (V) 170 (H)/ 160 (V) 178 (H)/ 178 (V)

50,000 hrs 30,000 hrs 50,000 hrs 50,000 hrs

Mounting VESA Mount 100 x 100

Dimensions(mm) 412 x 277.5 x 60.4 439 x 348 x 64.8 499.6 x 314.6 x 60 557 x 362 x 64.8

ARCHMI-8XX Series User Manual

10

1.3 Dimensions

Figure 1.1: Dimensions of ARCHMI-807

Figure 1.2: Dimensions of ARCHMI-808

ARCHMI-8XX Series User Manual

11

Figure 1.3: Dimensions of ARCHMI-810

Figure 1.4: Dimensions of ARCHMI-812

ARCHMI-8XX Series User Manual

12

Figure 1.5: Dimensions of ARCHMI-815

Figure 1.6: Dimensions of ARCHMI-816

ARCHMI-8XX Series User Manual

13

Figure 1.7: Dimensions of ARCHMI-817

Figure 1.8: Dimensions of ARCHMI-818

ARCHMI-8XX Series User Manual

14

Figure 1.9: Dimensions of ARCHMI-821

ARCHMI-8XX Series User Manual

15

1.4 Brief Description of ARCHMI-8XX

There are 7”, 8”, 10.1”, 12.1”, 15”, 15.6”, 17”, 18.5” and 21.5” Industrial

Compact Size Panel PC in ARCHMI-8XX series, which comes with flat front panel touch screen and fanless design. It is powered by Intel Bay Trail E3845(1.91GHz) or

N2930(1.83GHz) CPU built-in, 2GB DDR3L 1600 MHz (4GB is for option). ARCHMI series is 9~36V DC wide-ranging power input and IP65 compliant front panel.

Optional projected capacitive touch support 7H anti-scratch surface is ideal for use as

PC-based controller for Industrial Automation & Factory Automation.

Figure 1.10: Front View of ARCHMI-8XX Series

ARCHMI-8XX Series User Manual

16

Figure 1.11: Rear View of ARCHMI-807/808

Figure 1.12: Rear View of ARCHMI-810

ARCHMI-8XX Series User Manual

17

Figure 1.13: Rear View of ARCHMI-812

Figure 1.14: Rear View of ARCHMI-815

ARCHMI-8XX Series User Manual

18

Figure 1.15: Rear View of ARCHMI -816

Figure 1.16: Rear View of ARCHMI-817

ARCHMI-8XX Series User Manual

19

Figure 1.17: Rear View of ARCHMI-818

Figure 1.18: Rear View of ARCHMI-821

ARCHMI-8XX Series User Manual

20

1.5 Installation of HDD – 7” and 8”

Step 1

There are two screws to deal with when enclosing or removing the chassis.

Gently remove two screws.

Step 2

There is a SSD card in the bracket. Gently remove the screw, then carefully pull

SSD card.

Step 3

Take out SSD Card bracket.

ARCHMI-8XX Series User Manual

21

Step 4

You can replace SSD card by unscrewing four screws as shown in the picture.

Note: four screws are packed in the packing list.

Step 5

There is a SD card hole in the side of the machine. You can replace SD card from there.

Step 6

Gently screw the screws.

ARCHMI-8XX Series User Manual

22

1.6 Installation of HDD – 10.1”/15.6”/18.5”

Step 1

There are two screws to deal with when enclosing or removing the chassis.

Gently remove two screws.

Step 2

Take the storage cover beside the HMI.

Step 3

You can put or remove HDD into the machine by pulling the HDD bracket.

ARCHMI-8XX Series User Manual

23

Step 4

There is a SD hole in the side of machine.

You can replace SD card from there.

1.7 Installation of HDD – 12.1”/15”/17”/21.5”

Step 1

There are 2 screws to deal with when enclosing or removing the chassis.

Gently remove 2 screws.

Step 2

You can put or remove HDD into the machine by pulling the HDD bracket.

ARCHMI-8XX Series User Manual

24

Step 3

You can remove HDD by unscrewing 4 screws in the HDD bracket.

Note: 4 screws are packed in the packing package.

Step 4

There is a SD hole in the side of machine.

You can replace SD card from there

.

ARCHMI-8XX Series User Manual

25

Chapter 2 Hardware

2.1 Mainboard Introduction

SBC-7111 is a 4" industrial motherboard developed on the basis of Intel Bay trail-I/M

Processors, which provides abundant peripheral interfaces to meet the needs of different customers. Also, it features dual GbE ports, 3-COM ports and one Mini PCIE configuration, one VGA port, one HDMI port, one LVDS interface. To satisfy the special needs of high-end customers, CN1 and CN2 and CN3 richer extension functions. The product is widely used in various sectors of industrial control.

2.2 Specifications

Specifications

Board Size

CPU Support

170mm x 113mm

Intel Bay Trail E3845 / 1.91GHz (4cores, 10W, onboard)

Intel Bay Trail N2930 / 1.83 up to 2.16GHz (4cores,TDP/7.5W, option)

Intel Bay Trail E3815 / 1.46GHz (1core, 5W, option)

Chipset

Memory Support

Graphics

Display Mode

Support

Resolution

SoC

Onboard 2GB DDR3L SDRAM (E3845/N2930/E3815, option)

Onboard 4GB DDR3L SDRAM (E3845/N2930, option)

Intel® HD Graphics 542/792MHz (E3845)

Intel® HD Graphics 313/854MHz (N2930)

Intel® HD Graphics 400MHz (E3815)

1 x HDMI Port

1 x LVDS (18/24-bit dual LVDS)

1 x CRT Port

Up to 1920 x 1200 for HDMI

Up to 1920 x 1200 for LVDS (PS8625)

Up to 1920 x 1200 for CRT

Dual Display

HDMI + LVDS

HDMI + CRT

LVDS + CRT

Super I/O ITE IT8518E

ARCHMI-8XX Series User Manual

26

BIOS

Storage

Ethernet

USB

Serial

Digital I/O

Battery

Smart Battery

Audio

Keyboard /Mouse

Expansion Bus

Touch Ctrl

Fintek F81216AD

AMI/UEFI

1 x SATAII Connector (7P)

1 x SATAII Connector (7P + 15P)

1 x SD Slot

2 x PCIe Gbe LAN by Intel 82574L

1 x USB 2.0 and 1 x USB 3.0 (type A)stack ports (USBCON1/USB0,USB1)

1 x USB 2.0 Pin header for CN1 (USB3 or Touch, option)

1 x USB 2.0 Hub(USB2)

1 x USB 2.0 Pin header for CN2 (USB Hub /USB1)

2 x USB 2.0 Pin header for CN3 (USB Hub /USB2/USB3)

1 x USB 2.0 for MPCIE1 (USB Hub /USB4)

1 x RS232/RS422/RS485 port, DB9 connector for external (COM1) Pin 9 w/5V/12V/Ring select

1 x RS232 port, DB9 connector for external (COM2) Pin 9 w/5V/12V/Ring select

2 x UART for CN3 (COM3,COM4)

1 x RS422/485 header for CN2 (IT8518E/COM5)

8-bit digital I/O by Pin header (CN2)

4-bit digital Input

4-bit digital Output

4-bit digital I/O by Pin header (CN3)

2-bit digital Input

2-bit digital Output

Support CR2477 Li battery by 2-pin header (BAT1/CMOS)

1 x Smart battery

Support 3 Serial Li battery by 8-pin header (BAT2)

Support Audio via Realtek ALC662-VD HD audio codec

Support Line-in, Line-out, MIC by 2x6-pin header

1 x PS2 keyboard/mouse by box pin header (CN3)

1 x mini-PCI-express slot

1 x PCI-express (CN3)

1 x Touch ctrl header for TCH1 (ITE8518E/COM6)

(JP4 setting:RS232 or USB 2.0)

ARCHMI-8XX Series User Manual

27

Power Management

Switches and

LED Indicators

External I/O port

Watchdog Timer

Temperature

Humidity

Power Consumption

EMI/EMS

Wide Range DC9V~36V input

1 x 3-pin power input connector

1 x Power on/off switch (BT1/BT2/CN2/CN3)

1 x Reset (CN2)

1 x Power LED status (CN1)

1 x HDD LED status (CN2)

1 x Buzzer

2 x COM Ports (COM1/COM2)

2 x USB 2.0 Ports (stack)

2 x RJ45 GbE LAN Ports

1 x HDMI Port

1 x Stack audio Jack (Line out)

Software programmable 1 – 255 second by Super I/O (Reserve)

Operating: -20℃ to 70℃

Storage: -40℃ to 85℃

10% - 90%, non-condensing, operating

2V /0.80A (Intel Bay Trail E3845 processor with 4GB DDR3L DRAM)

12V /0.70A (Intel Bay Trail N2930 processor with 4GB DDR3L DRAM)

12V /0.60A (Intel Bay Trail E3815 processor with 2GB DDR3L DRAM)

Meet CE/FCC class A

TB-528CAN2

2 x CAN bus

1 x SIM Card Socket

1 x mini-PCI-express slot

ARCHMI-8XX Series User Manual

28

(units :mm)

Figure 2.1: Mainboard Dimensions

ARCHMI-8XX Series User Manual

29

2.3 Jumpers and Connectors Location

Figure 2.2: Jumpers and Connectors Location- Board Top

Figure 2.3: Jumpers and Connectors Location- Board Bottom

ARCHMI-8XX Series User Manual

30

2.4 Jumpers Setting and Connectors

1. U2:

(FCBGA1170), onboard Intel Bay trail-I/M Processors.

Model

Number PBF

SBC-7111-E3845-2G E3845 1.91GHz

SBC-7111-E3845-4G E3845 1.91GHz

Processor

Cores/Threads TDP Remarks

4 / 4 10W

4 / 4

4 / 4

10W

4.5 /

7.5W

Option

Option SBC-7111-N2930-2G N2930 1.83 up to

2.16GHz

SBC-7111-N2930-4G

SBC-7111-E3815-2G

N2930

E3815

1.83 up to

2.16GHz

1.46GHz

4 / 4

1 / 1

4.5 /

7.5W

5W

Option

Option

2. H3/H4/H5/H6(option):

U2 Heat Sink Screw holes, four screw holes for intel Bay trail-I/M Processors

Heat Sink assemble.

3. U3/U4/U5/U6:

(FBGA96)Onboard DDR3L Memory.

Model

SBC-7111-E3845-2G

SBC-7111-N2930-2G

SBC-7111-E3815-2G

Memory

2GB

2GB (option)

2GB (option)

SBC-7111-E3845-4G

SBC-7111-N2930-4G

4GB (option)

4GB (option)

4. S-422 (PIN6):

(Switch),ATX Power and Auto Power on jumper setting.

S-422(Switch) Mode

Pin6 (Off)

Pin6 (On)

ATX Power

Auto Power on (Default)

5. BAT1 :

(1.25mm Pitch 1x2 Wafer Pin Header) 3.0V Li battery is embedded to provide power for CMOS.

ARCHMI-8XX Series User Manual

31

Pin#

1

2

Signal Name

VBAT

Ground

6. SW1NC:

(2.0mm Pitch 2x2 Pin Header),Reserve.

7. BAT2NC:

(2.0mm Pitch 1x8 Wafer Pin Header),Reserve.

8. LED3/LED4NC:

LED3:Reserve.

LED4:Reserve.

9. DC_IN1:

(5.08mm Pitch 1x3 Pin Connector),DC9V~36V System power input connector.

Pin#

1

2

3

Power input

DC+9V~36V

Ground

FG

Model

SBC-7111-E3845-2G

SBC-7111-E3845-4G

SBC-7111-N2930-2G

SBC-7111-N2930-4G

SBC-7111-E3815-2G

SBC-7111-E3845P-2G

SBC-7111-E3845P-4G

DC_IN1

180°Connector

180°Connector

180°Connector

180°Connector

180°Connector

45°Connector

45°Connector

10. BT1/BT2:

Power on/off button, They are used to connect power switch button. The two pins are disconnected under normal condition. You may short them temporarily to realize system startup & shutdown or awaken the system from sleep state.

11. FAN1(option):

(2.54mm Pitch 1x3 Pin Header),Fan connector, cooling fans can be connected

ARCHMI-8XX Series User Manual

32

directly for use. You may set the rotation condition of cooling fan in menu of

BIOS CMOS Setup.

Pin#

1

2

3

Signal Name

Ground

VCC

Rotation detection

Note:

Output power of cooling fan must be limited under 5W.

12. VGA_PH1:

(CRT 2.0mm Pitch 2x6 Pin Header), Video Graphic Array Port, Provide 2x6Pin cable to VGA Port.

Signal Name Pin# Pin# Signal Name

CRT_RED 1 2 Ground

CRT_GREEN

CRT_BLUE

CRT_H_SYNC

CRT_V_SYNC

Ground

3

5

7

9

11

4

6

Ground

VGA_EN

8 CRT_DDCDATA

10

12

CRT_DDCCLK

Ground

VGA hot plug setting for Windows XP:

VGA1 (Pin Header) Function

Pin4-Pin6 (Close) VGA Simulation Disabled

Pin4-Pin6 (Open) VGA Simulation Enabled

Use the 2.0mm jumper cap to close pin4 and pin6

13. HDMI1:

(HDMI 19P Connector), High Definition Multimedia Interface connector.

14. JP6:

(2.0mm Pitch 2x2 Pin Header), LVDS jumper setting.

ARCHMI-8XX Series User Manual

33

JP6

Pin1-Pin2 (Close)

Pin1-Pin2 (Open)

Pin3-Pin4 (Close)

Pin3-Pin4 (Open)

Function (CN1)

Single channel LVDS

Dual channel LVDS (Default)

8/24 bit (Default)

6/18 bit

15. U18:

AT24C02-DIP8,The EEPROM IC(U18)is the set of LVDS resolution. If you need other resolution settings, please upgrade U18 data.

Model LVDS resolution

SBC-7111-E3845-2G

SBC-7111-E3845-4G

SBC-7111-N2930-2G

SBC-7111-E3845-4G

SBC-7111-E3815-2G

1280*1024 (Default)

800*480 (option)

800*600 (option)

1024*768 (option)

1920*1080 (option)

……

16. INVT1:

(2.0mm Pitch 1x6 wafer Pin Header), Backlight control connector for LVDS.

Pin#

1

2

3

4

5

6

Signal Name

+DC12V

+DC12V

Ground

Ground

BKLT_EN_OUT

BKLT_CTRL

17. CN1:

(1.25mm Pitch 2x20 Connector, DF13-40P), for 18/24-bit LVDS output connector,

ARCHMI-8XX Series User Manual

34

fully supported by Parad PS8625(DP to LVDS), the interface features dual channel 24-bit output. Low Voltage Differential Signaling, A high speed, low power data transmission standard used for display connections to LCD panels.

Function

LVDS

USB3

(JP4 open)

Power LED

Signal Name Pin# Pin# Signal Name

12V_S0

BKLT_EN_OUT

2

4

1

3

12V_S0

BKLT_CTRL

Ground

LVDS_VDD5

LVDS_VDD3

Ground

6

8

10

12

5

7

9

11

Ground

LVDS_VDD5

LVDS_VDD3

Ground

LA_D0_P

LA_D1_P

LA_D2_P

LA_D3_P

LA_CLKP

LB_D0_P

LB_D1_P

LB_D2_P

LB_D3_P

LB_CLKP

Ground

USB3_P

5V_S5_USB

PWR_LED+

14

16

18

20

22

24

26

28

30

32

34

36

38

40

13

15

17

19

21

23

25

27

29

31

33

35

37

39

LA_D0_N

LA_D1_N

LA_D2_N

LA_D3_N

LA_CLKN

LB_D0_N

LB_D1_N

LB_D2_N

LB_D3_N

LB_CLKN

Ground

USB3_N

5V_S5_USB

Ground

Function

LVDS

USB3

(JP4 open)

Power LED

18. JP4:

(2.0mm Pitch 2x2 wafer Pin Header), USB3(CN1) or Touch jumper setting.

JP4

USB3 (CN1)

Function

Touch (TCH1)

Close 3-4 (default)

Open 3-4 (option)

Open 1-2 (default)

-

Yes

-

Yes

-

19. TCH1:

(2.0mm Pitch 1x6 wafer Pin Header), internal Touch controller connector.

ARCHMI-8XX Series User Manual

35

Pin#

1

2

3

4

5

6

Signal Name

SENSE

X+

X-

Y+

Y-

GND_EARCH

20. JP1:

(2.0mm Pitch 2x3 Pin Header), COM1 jumper setting, pin 1~6 are used to select signal out of pin 9 of COM1 port.

JP1 Pin#

Close 1-2

Close 3-4

Close 5-6

Function

COM1 RI (Ring Indicator) (default)

COM1 Pin9: DC+5V (option)

COM1 Pin9: DC+12V (option)

21. S_232:

(Switch), COM1 jumper setting, it provides selectable RS232 or RS422 or RS485 serial signal output.

Function S_232 Pin#

RS232 (Default) ON: Pin1, Pin2, Pin3, Pin4

RS422 (option) OFF: Pin1, Pin2, Pin3, Pin4

RS485 (option) OFF: Pin1, Pin2, Pin3, Pin4

22. S_422:

(Switch), COM1 setting, it provides selectable RS232 or RS422 or RS485 serial signal output.

Function S_422 Pin#

RS232 (Default) OFF: Pin1, Pin2, Pin3, Pin4, Pin5

RS422 (option) ON: Pin1, Pin2, Pin3, Pin4, Pin5

RS485 (option) ON: Pin1, Pin2, Pin3, Pin4, Pin5

S-422

Pin6 (Off)

Pin6 (On)

Mode

ATX Power

Auto Power on (Default)

ARCHMI-8XX Series User Manual

36

23. COM1:

(Type DB9M), Rear serial port, standard DB9 Male serial port is provided to make a direct connection to serial devices. COM1 port is controlled by pins

No.1~6 of JP1, select output Signal RI or 5V or 12V, for details, please refer to description of JP1 and S_232 and S_422 setting.

RS232 (Default)

Pin#

1

2

3

4

5

6

7

8

9

Signal Name

DCD# (Data Carrier Detect)

RXD (Received Data)

TXD (Transmit Data)

DTR (Data Terminal Ready)

Ground

DSR (Data Set Ready)

RTS (Request To Send)

CTS (Clear To Send)

JP1 select Setting (RI/5V/12V)

BIOS Setup:

Advanced/F81216SEC Super IO Configuration/Serial Port 1 Configuration 【RS-232】

RS422 (option)

Pin#

1

2

5

6

3

4

7

8

9

Signal Name

422_RX+

422_RX-

422_TX-

422_TX+

Ground

NC

NC

NC

NC

BIOS Setup:

Advanced/F81216SEC Super IO Configuration/Serial Port 1 Configuration 【RS-422】

ARCHMI-8XX Series User Manual

37

RS485 (option)

Pin#

1

2

3

4

5

6

7

8

9

Signal Name

NC

NC

485-

485+

Ground

NC

NC

NC

NC

BIOS Setup:

Advanced/F81216SEC Super IO Configuration/Serial Port 1 Configuration 【RS-485】

24. JP2:

(2.0mm Pitch 2x3 Pin Header), COM2 jumper setting, pin 1~6 are used to select signal out of pin 9 of COM2 port.

JP2 Pin#

Close 1-2

Close 3-4

Close 5-6

Function

COM2 RI (Ring Indicator) (default)

COM2 Pin9: DC+5V (option)

COM2 Pin9: DC+12V (option)

25. COM2:

(Type DB9M),Rear serial port, standard DB9 Male serial port is provided to make a direct connection to serial devices.

6

7

8

9

Pin#

1

2

3

4

5

ARCHMI-8XX Series User Manual

Signal Name

DCD# (Data Carrier Detect)

RXD (Received Data)

TXD (Transmit Data)

DTR (Data Terminal Ready)

Ground

DSR (Data Set Ready)

RTS (Request To Send)

CTS (Clear To Send)

JP2 select Setting (RI/5V/12V)

38

26. LED1,LED2 (option) :

LED1: LED STATUS. Green LED for Motherboard Standby Power Good status.

LED2: LED STATUS. Green LED for Touch Power status.

27. SATA_P:

(2.5mm Pitch 1x2 box Pin Header), One onboard 5V output connector are reserved to provide power for SATA devices.

Pin#

1

2

Signal Name

+DC5V

Ground

Note:

Output current of the connector must not be above 1A.

28. SATA2:

(SATA 7Pin), SATA Connectors, one SATA connector are provided, with transfer speed up to 3.0Gb/s.

29. SATA1:

(SATA 7Pin+15Pin), SATA Connectors, one SATA connector are provided, with transfer speed up to 3.0Gb/s.

30. SD1:

(SD card slot), Secure Digital Memory Card socket.

31. MPCIE1:

(Socket 52Pin), mini PCIe socket, it is located at the top, it supports mini PCIe devices with USB2.0 and LPC and SMBUS and PCIe signal. MPCIe card size is

30x50.95mm.

32. H1/H2:

MPCIE1 SCREW HOLES, H1and H2 for mini PCIE card (30mmx50.95mm) assemble.

33. F_AUDIO1:

(2.0mm Pitch 2X6 Pin Header), Front Audio, An onboard Realtek ALC662-VD codec is used to provide high-quality audio I/O ports. Line Out can be connected to a headphone or amplifier. Line In is used for the connection of

ARCHMI-8XX Series User Manual

39

external audio source via a Line in cable. MIC is the port for microphone input audio.

Signal Name Pin# Pin# Signal Name

+5V

LINE-OUT-L

FRONT_JD

LINE_IN-L

1

3

5

7

2

4

6

8

GND_AUD

LINE-OUT-R

LINE1_JD

LINE-IN-R

MIC-IN-L

GND-AUD

9

11

10

12

MIC-IN-R

MIC1_JD

34. LINE_OUT1:

(Diameter 3.5mm Jack), HD Audio port, An onboard Realtek ALC662-VD codec is used to provide high quality audio I/O ports. Line Out can be connected to a headphone or amplifier.

35. USBCON1:

USB0/USB1:(Double stack USB type A), Rear USB connector, it provides up to two USB2.0 port, High-speed USB 2.0 allows data transfers up to 480 Mb/s, support USB full-speed and low-speed signaling.

Each USB Type A Receptacle (2 Ports) Current limited value is 1.5A.

If the external USB device current exceeds 1.5A, please separate connectors

into different Receptacle.

36. LAN1/LAN2:

LAN1/LAN2: (RJ45 Connector), Rear LAN port, Two standard 10/100/1000M

RJ-45 Ethernet ports are provided. Used intel 82574L chipset, LINK LED (green) and ACTIVE LED (yellow) respectively located at the left-hand and right-hand side of the Ethernet port indicate the activity and transmission state of LAN.

37. BUZ1:

Onboard buzzer.

ARCHMI-8XX Series User Manual

40

38. CN2:

(DF13-30P Connector),For expand output connector, It provides eight

GPIO,one RS422 or RS485,one USB2.0,one Power on/off, one Reset.

Function

5V

SOC_GPIO10

Signal Name

5V_S5

GPIO_IN2

Pin#

2

4

Pin#

1

3

Signal Name

5V_S5

GPIO_IN1

Function

5V

SOC_SPIO09

SOC_GPIO26

SOC_GPIO05

SOC_GPIO08

GPIO_IN4

GPIO_OUT2

GPIO_OUT4

Ground

6

8

10

12

5

7

9

11

GPIO_IN3 SOC_GPIO17

GPIO_OUT1 SOC_GPIO04

GPIO_OUT3 SOC_GPIO06

Ground

485 or 422

RS422

485+_422TX+ 14

422_RX+ 16

13 485-_422TX- 485 or 422

15 422_RX- RS422

5V

USB2.0

Power auto on

NC

NC

5V_S0

5V_USB01

USBDN1_P

Ground

PWRBTN_ON

18

20

22

24

26

28

30

17

19

21

23

25

27

29

NC

NC

HDD_LED+

5V_USB01

USBDN1_N

FP_RST-

Ground

HDD LED

USB2.0

RESET

COM5 BIOS Setup:

Advanced/IT8518Super IO Configuration/Serial Port 1 Configuration【RS-422】

Advanced/IT8518Super IO Configuration/Serial Port 1 Configuration【RS-485】

39. EC_GPIO1:

(2.0mm Pitch 1X10 Pin Header),For expand connector, it provides eight GPIO.

Pin# Signal Name

3

4

5

1

2

6

7

8

9

10

Ground

EC_GPIO1

EC_GPIO2

EC_GPIO3

EC_GPIO4

EC_GPIO5

EC_GPIO6

EC_GPIO7

EC_GPIO8

3.3V

ARCHMI-8XX Series User Manual

41

40. CN3:

(1.27mm Pitch 2X30 Female Header), for expand output connector,It provides four GPIO,two USB 2.0,one PS/2 mouse,one PS/2 keyboard, two uart,one

PCIex1, one SMbus. connected to the TB-528 riser Card.

Function Signal Name

5V_S5_USB

5V_S5_USB

Pin#

1

3

Pin#

2

4

Signal Name

5V_S5_USB

5V_S5_USB

Function

Exp-USB2

Exp-USB3

PS/2 MS

PS/2 KB

COM4

(UART)

COM3

(UART)

GPIO23

GPIO25

PCIE

SMBUS

PCIE

12V

USB23_OC

USB2_DM

USB3_DM

Ground

PS2_MSCLK

PS2_KBCLK

COM4_RI

COM4_TXD

5

7

6

8

9 10

11 12

13 14

15 16

17 18

19 20

PSON_ATX-

USB2_DP

USB3_DP

Ground

PS2_MSDATA

PS2_KBDATA

COM4_DCD-

COM4_RXD

Exp-USB2

Exp-USB3

PS/2 MS

PS/2 KB

COM4

(UART)

COM4_DTR

COM4_DSR

Ground

COM3_RI

COM3_TXD

COM3_DTR

COM3_DSR

SOC_GPIO23

SOC_GPIO25

Ground

21 22

23 24

RICOM4_RTS-

COM_CTS-

25 26

27 28

29 30

Ground

COM3_DCD-

COM3_RXD

31 32 DSRCOM3_RTS-

33 34 DTRCOM3_CTS-

35 36 ICH_GPIO22

37 38

39 40

ICH_GPIO24

Ground

COM3

(UART)

PCIE_TX0_DN

PCIE_RX0_DN

Ground

41 42

43 44

45 46

PCIE_TX0_DP

PCIE_RX0_DP

Ground

PCIE_REFCLK0_DN 47 48 PCIE_REFCLK0_DP

PCIE0_WAKE_N 49 50 PLTRST_3P3_N

GPIO12

GPIO24

PCIE

SMB_CLK_S0 51 52 SMB_DATA_S0

PCIE_CLKREQ0_N 53 54 Ground

3P3V_S5 55 56

SMBUS

PWRBTN_ON- Power Auto on

3P3V_S5

12V_S0

57 58

59 60

3P3V_S5

12V_S0 12V

ARCHMI-8XX Series User Manual

42

41. TB-528C2ME1option:

SBC-7111 Riser Card, TB-528C2ME1 CN3 connect to SBC-7111 CN3 pin Header.

TB-528C2ME1 Top:

CN3

(1.27mm Pitch 2X30 Pin Header), connect to SBC-7111 CN3 pin Header.

M-PCIE1

(Socket 52Pin), mini PCIe socket, it is located at the top, it supports mini PCIe devices with USB2.0(USB2),Smbus,SIM and PCIe signal. MPCIe card size is

30x30mm or 30x50.95mm.

Signal Name

PCIe 1X

USB2.0 (USB2)

SMBus

SIM

Function support

Yes

Yes

Yes

Yes

H1/H2:

MPCIE1 SCREW HOLES, H2 for mini PCIE card (30mmx30mm) assemble. H1 for mini PCIE card (30mmx50.95mm) assemble.

LED1

Mini PCIe devices LED Status.

ARCHMI-8XX Series User Manual

43

SIM1

(SIM Socket 6 Pin), Support SIM Card devices.

PS2

(2.0mm Pitch 1X6 Pin Wafer), PS/2 keyboard and mouse port, the port can be connected to PS/2 keyboard or mouse via a dedicated cable for direct used.

Pin#

1

2

Signal Name

KBDATA

MSDATA

3

4

5

6

Ground

+5V

KBCLK

MSCLK

GPIO1

(2.0mm Pitch 2x5 Pin Header),General-purpose input/output port, it provides a group of self-programming interfaces to customers for flexible use.

Signal Name Pin# Pin# Signal Name

Ground

NC

1

3

2

4

NC

SMB_DATA_R

SMB_CLK_R

SOC-GPIO23

5

7

6

8

SOC-GPIO22

SOC-GPIO25

SOC-GPIO24 9 10 +5V

USB_23

(2.0mm Pitch 2x5 Pin Header) ,Front USB connector, it provides one USB port via a dedicated USB cable, speed up to 480Mb/s.

Signal Name Pin# Pin# Signal Name

5V_USB23

USB3_N

USB3_P

Ground

NC

1

3

5

7

9

2

4

6

8

10

5V_USB23

USB2_N (option, NC)

USB2_P (option, NC)

Ground

Ground

ARCHMI-8XX Series User Manual

44

Note:

Before connection, make sure that pinout of the USB Cable is in accordance with that of the said tables. Any inconformity may cause system down and even hardware damages.

JP5

(2.0mm Pitch 2x3 Pin Header), COM5 setting jumper, pin 1~6 are used to select signal out of pin 9 of COM5 port.

JP5 Pin#

Close 1-2

Close 3-4

Close 5-6

Function

RI (Ring Indicator) (default)

COM5 Pin9=+5V (option)

COM5 Pin9=+12V (option)

COM5(SBC-7111/COM3)

(Type DB9), serial port, standard DB9 serial port is provided to make a direct connection to serial devices. COM5 port is controlled by pins No.1~6 of JP5, select output Signal RI or 5V or 12v, For details, please refer to description of JP3.

Pin#

1

2

3

4

5

6

7

8

9

ARCHMI-8XX Series User Manual

Signal Name

DCD# (Data Carrier Detect)

RXD (Received Data)

TXD (Transmit Data)

DTR (Data Terminal Ready)

Ground

DSR (Data Set Ready)

RTS (Request To Send)

CTS (Clear To Send)

JP5 Setting:

Pin1-2: RI (Ring Indicator) (default)

Pin3-4 : 5V Standby power (option)

Pin5-6: 12V Standby power (option)

45

JP6

(2.0mm Pitch 2x3 Pin Header), COM6 setting jumper, pin 1~6 are used to select signal out of pin 9 of COM6 port.

JP6 Pin#

Close 1-2

Close 3-4

Close 5-6

Function

RI (Ring Indicator) (default)

COM6 Pin9=+5V (option)

COM6 Pin9=+12V (option)

COM6(SBC-7111/COM4)

(Type DB9), serial port, standard DB9 serial port is provided to make a direct connection to serial devices. COM6 port is controlled by pins No.1~6 of JP6, select output Signal RI or 5V or 12v, For details, please refer to description of JP6.

Pin#

1

2

3

4

5

6

7

8

9

Signal Name

DCD# (Data Carrier Detect)

RXD (Received Data)

TXD (Transmit Data)

DTR (Data Terminal Ready)

Ground

DSR (Data Set Ready)

RTS (Request To Send)

CTS (Clear To Send)

JP6 Setting:

Pin1-2: RI (Ring Indicator) (default)

Pin3-4 : 5V Standby power (option)

Pin5-6: 12V Standby power (option)

COM_6option,SBC-7111/COM4):

(2.0mm Pitch 2X5 Pin Header), COM6 Port, up to one standard RS232 port are provided. They can be used directly via COM cable connection.

Signal Name

DCD

TXD

ARCHMI-8XX Series User Manual

Pin#

1

3

Pin#

2

4

Signal Name

RXD

DTR

46

Ground

RTS

JP6 Setting: RI/5V/12V

5

7

9

6

8

10

DSR

CTS

NC

42. TB-528C2option:

SBC-7111 Riser Card, TB-528C2ME1 CN3 connect to SBC-7111 CN3 pin

Header.

TB-528C2ME1 Top:

CN3

(1.27mm Pitch 2X30 Pin Header), connect to SBC-7111 CN3 pin Header.

LED1

Mini PCIe devices LED Status.

PS2

(2.0mm Pitch 1X6 Pin Wafer), PS/2 keyboard and mouse port, the port can be connected to PS/2 keyboard or mouse via a dedicated cable for direct used.

Pin#

1

2

5

6

3

4

ARCHMI-8XX Series User Manual

Signal Name

KBDATA

MSDATA

Ground

+5V

KBCLK

MSCLK

47

GPIO1

(2.0mm Pitch 2x5 Pin Header), General-purpose input/output port, it provides a group of self-programming interfaces to customers for flexible use.

Signal Name

Ground

NC

SMB_CLK_R

SOC-GPIO23

SOC-GPIO24

Pin# Pin#

1

3

5

7

9

2

4

6

8

10

Signal Name

NC

SMB_DATA_R

SOC-GPIO22

SOC-GPIO25

+5V

USB_23

(2.0mm Pitch 2x5 Pin Header), Front USB connector, it provides one USB port via a dedicated USB cable, speed up to 480Mb/s.

Signal Name

5V_USB23

USB3_N

USB3_P

Pin#

1

3

5

Pin#

2

4

6

Signal Name

5V_USB23

USB2_N

USB2_P

Ground

NC

7

9

8

10

Ground

Ground

Note:

Before connection, make sure that pinout of the USB Cable is in accordance with that of the said tables. Any inconformity may cause system down and even hardware damages.

JP5

(2.0mm Pitch 2x3 Pin Header), COM5 setting jumper, pin 1~6 are used to select signal out of pin 9 of COM5 port.

JP5 Pin#

Close 1-2

Close 3-4

Close 5-6

ARCHMI-8XX Series User Manual

Function

RI (Ring Indicator) (default)

COM5 Pin9=+5V (option)

COM5 Pin9=+12V (option)

48

COM5(SBC-7111/COM3)

(Type DB9), serial port, standard DB9 serial port is provided to make a direct connection to serial devices. COM5 port is controlled by pins No.1~6 of JP5, select output Signal RI or 5V or 12v, For details, please refer to description of JP3.

Pin#

1

2

3

4

5

6

7

8

9

Signal Name

DCD# (Data Carrier Detect)

RXD (Received Data)

TXD (Transmit Data)

DTR (Data Terminal Ready)

Ground

DSR (Data Set Ready)

RTS (Request To Send)

CTS (Clear To Send)

JP5 Setting:

Pin1-2: RI (Ring Indicator) (default)

Pin3-4 : 5V Standby power (option)

Pin5-6: 12V Standby power (option)

JP6

(2.0mm Pitch 2x3 Pin Header), COM6 setting jumper, pin 1~6 are used to select signal out of pin 9 of COM6 port.

JP6 Pin#

Close 1-2

Close 3-4

Close 5-6

Function

RI (Ring Indicator) (default)

COM6 Pin9=+5V (option)

COM6 Pin9=+12V (option)

COM6(SBC-7111/COM3)

(Type DB9), serial port, standard DB9 serial port is provided to make a direct connection to serial devices. COM6 port is controlled by pins No.1~6 of JP6, select output Signal RI or 5V or 12v, For details, please refer to description of JP6.

ARCHMI-8XX Series User Manual

49

Pin#

1

2

3

4

5

6

7

8

9

Signal Name

DCD# (Data Carrier Detect)

RXD (Received Data)

TXD (Transmit Data)

DTR (Data Terminal Ready)

Ground

DSR (Data Set Ready)

RTS (Request To Send)

CTS (Clear To Send)

JP6 Setting:

Pin1-2: RI (Ring Indicator) (default)

Pin3-4 : 5V Standby power (option)

Pin5-6: 12V Standby power (option)

COM_6optionSBC-7111/COM3):

(2.0mm Pitch 2X5 Pin Header), COM6 Port, up to one standard RS232 port are provided. They can be used directly via COM cable connection.

Signal Name

DCD

Pin#

1

Pin#

2

Signal Name

RXD

TXD

Ground

RTS

3

JP6 Setting: RI/5V/12V 9

5

7

4

6

8

10

DTR

DSR

CTS

NC

43. TB-528C1U2P1/TB-528C1U2option:

SBC-7111 Riser Card, TB-528C1U2P1 CN3 connect to SBC-7111 CN3 pin

Header.

TB-528C1U2P1 Top:

ARCHMI-8XX Series User Manual

50

CN3

(1.27mm Pitch 2X30 Pin Header), connect to SBC-7111 CN3 pin Header.

M-PCIE1

(Socket 52Pin), mini PCIe socket, it is located at the top, it supports mini

PCIe devices with Smbus,SIM and PCIe signal. MPCIe card size is 30x30mm or 30x50.95mm.

Signal Name

PCIe 1X

USB2.0 (USB2)

SMBus

SIM

Function support

Yes

NC (option)

Yes

Yes

H1/H2:

MPCIE1 SCREW HOLES, H2 for mini PCIE card (30mmx30mm) assemble. H1 for mini PCIE card (30mmx50.95mm) assemble.

LED1

Mini PCIe devices LED Status.

SIM1option):

(SIM Socket 6 Pin), Support SIM Card devices.

PS_ON1

(2.0mm Pitch 1X2 Pin Wafer), ATX Power and Auto Power on jumper setting.

ARCHMI-8XX Series User Manual

51

PS_ON

Close 1-2

Open 1-2

Mode

Auto Power on (Default)

ATX Power

PS_ON2option):

(2.0mm Pitch 1X2 Pin Wafer).

PS2

(2.0mm Pitch 1X6 Pin Wafer), PS/2 keyboard and mouse port, the port can be connected to PS/2 keyboard or mouse via a dedicated cable for direct used.

Pin#

1

2

Signal Name

KBDATA

MSDATA

3

4

5

6

Ground

+5V

KBCLK

MSCLK

GPIO1

(2.0mm Pitch 2x5 Pin Header), General-purpose input/output port, it provides a group of self-programming interfaces to customers for flexible use.

Signal Name

Ground

NC

SMB_CLK_R

Pin#

1

3

5

Pin#

2

4

6

Signal Name

NC

SMB_DATA_R

SOC-GPIO22

SOC-GPIO23

SOC-GPIO24

7

9

8

10

SOC-GPIO25

+5V

USB23

(Double stack USB type A), Rear USB connector, it provides up to 2 USB2.0 ports, speed up to 480Mb/s.

ARCHMI-8XX Series User Manual

52

USB_23option):

(2.0mm Pitch 2x5 Pin Header) ,Front USB connector, it provides one USB port via a dedicated USB cable, speed up to 480Mb/s.

Signal Name

5V_USB23

USB3_N

Pin#

1

3

Pin#

2

4

Signal Name

5V_USB23

USB2_N

USB3_P

Ground

NC

5

7

9

6

8

10

USB2_P

Ground

Ground

Note:

Before connection, make sure that pinout of the USB Cable is in accordance with that of the said tables. Any inconformity may cause system down and even hardware damages.

JP5

(2.0mm Pitch 2x3 Pin Header), COM5 setting jumper, pin 1~6 are used to select signal out of pin 9 of COM5 port.

JP3 Pin#

Close 1-2

Close 3-4

Close 5-6

Function

RI (Ring Indicator) (default)

COM5 Pin9=+5V (option)

COM5 Pin9=+12V (option)

COM5(SBC-7111/COM3)

(Type DB9), serial port, standard DB9 serial port is provided to make a direct connection to serial devices. COM5 port is controlled by pins No.1~6 of JP5, select output Signal RI or 5V or 12v, for details, please refer to description of

JP3.

Pin#

1

2

3

4

5

ARCHMI-8XX Series User Manual

Signal Name

DCD# (Data Carrier Detect)

RXD (Received Data)

TXD (Transmit Data)

DTR (Data Terminal Ready)

Ground

53

6

7

8

9

DSR (Data Set Ready)

RTS (Request To Send)

CTS (Clear To Send)

JP5 Setting:

Pin1-2: RI (Ring Indicator) (default)

Pin3-4 : 5V Standby power (option)

Pin5-6: 12V Standby power (option)

JP6

(2.0mm Pitch 2x3 Pin Header), COM6 setting jumper, pin 1~6 are used to select signal out of pin 9 of COM6 port.

JP3 Pin#

Close 1-2

Function

RI (Ring Indicator) (default)

Close 3-4

Close 5-6

COM6 Pin9=+5V (option)

COM6 Pin9=+12V (option)

COM6(SBC-7111/COM4)

(Type DB9), serial port, standard DB9 serial port is provided to make a direct connection to serial devices. COM6 port is controlled by pins No.1~6 of JP6, select output Signal RI or 5V or 12v, For details, please refer to description of JP6.

Pin#

1

2

3

4

5

6

7

8

9

ARCHMI-8XX Series User Manual

Signal Name

DCD# (Data Carrier Detect)

RXD (Received Data)

TXD (Transmit Data)

DTR (Data Terminal Ready)

Ground

DSR (Data Set Ready)

RTS (Request To Send)

CTS (Clear To Send)

JP6 Setting:

Pin1-2: RI (Ring Indicator) (default)

Pin3-4 : 5V Standby power (option)

Pin5-6: 12V Standby power (option)

54

S1

PWR BT: POWER on/off Button, They are used to connect power switch button. The two pins are disconnected under normal condition. You may short them temporarily to realize system startup & shutdown or awaken the system from sleep state.

PWR LED: POWER LED status.

S1

Yes

No

Model

TB-528C1U2P1

TB-528C1U2

44. TB-528CAN2 R0.10option:

SBC-7111 Riser Card, TB-528CAN2 CN3 connect to SBC-7111 CN3 pin Header.

It provides two CAN-bus Interface.

TB-528CAN2 Top:

CN3

(1.27mm Pitch 2X30 Pin Header), connect to SBC-7111 CN3 pin Header.

M-PCIE1

(Socket 52Pin), mini PCIe socket, it is located at the top, it supports mini

PCIe devices with Smbus,USB2.0,SIM and PCIe signal. MPCIe card size is

30x30mm or 30x50.95mm

ARCHMI-8XX Series User Manual

55

Signal Name

PCIe 1X

USB2.0 (USB2)

SMBus

SIM

Function support

Yes

Yes

Yes

Yes

H1/H2:

MPCIE1 SCREW HOLES, H2 for mini PCIE card (30mmx30mm) assemble. H1 for mini PCIE card (30mmx50.95mm) assemble.

LED1

Mini PCIe devices LED Status.

SIM1option):

(SIM Socket 6 Pin), Support SIM Card devices.

PS2

(2.0mm Pitch 1X6 Pin Wafer), PS/2 keyboard and mouse port, the port can be connected to PS/2 keyboard or mouse via a dedicated cable for direct used.

Pin# Signal Name

1

2

KBDATA

MSDATA

3

4

5

6

Ground

+5V

KBCLK

MSCLK

USB_INoption):

(2.0mm Pitch 2x5 Pin Header) ,Front USB connector, it provides two USB port via a dedicated USB cable, speed up to 480Mb/s.

Signal Name

5V_USB23

NC (USB3_N)

Pin#

1

3

Pin#

2

4

Signal Name

5V_USB23

NC (USB2_N)

NC (USB3_P)

Ground

NC

5

7

9

6

8

10

NC (USB2_P)

Ground

Ground

ARCHMI-8XX Series User Manual

56

Note:

Before connection, make sure that pinout of the USB Cable is in accordance with that of the said tables. Any inconformity may cause system down and even hardware damages.

JP_SEToption):

(2.0mm Pitch 2x5 Pin Header).

Signal Name Pin# Pin#

3P3V_S5_USB

3P3V_S5_USB

3P3V_S5_USB

PSON_ATX

PSON_ATX

1

3

5

7

9

2

4

6

8

10

Signal Name

3P3V_S5

3P3V_S5

3P3V_S5

Ground

Ground

JP6

(2.0mm Pitch 2x3 Pin Header), COM6 setting jumper, pin 1~6 are used to select signal out of pin 9 of COM6 port.

JP3 Pin#

Close 1-2

Close 3-4

Close 5-6

Function

RI (Ring Indicator) (default)

COM6 Pin9=+5V (option)

COM6 Pin9=+12V (option)

COM6(SBC-7111/COM4)

(2.0mm Pitch 2X5 Pin Header), COM6 Port, up to one standard RS232 port are provided. They can be used directly via COM cable connection.

Signal Name

DCD

TXD

Ground

Pin#

1

3

5

Pin#

2

4

6

Signal Name

RXD

DTR

DSR

RTS 7

JP6 Setting: RI/5V/12V 9

8

10

CTS

NC

ARCHMI-8XX Series User Manual

57

COM5(SBC-7111/COM3)

(2.0mm Pitch 2X5 Pin Header), COM5 Port, up to one standard RS232 port are provided. They can be used directly via COM cable connection.

Signal Name

DCD

TXD

Ground

RTS

RI

Pin# Pin#

1

3

2

4

5

7

9

6

8

10

Signal Name

RXD

DTR

DSR

CTS

NC

GPIO1

(2.0mm Pitch 2x5 Pin Header), General-purpose input/output port, it provides a group of self-programming interfaces to customers for flexible use.

Signal Name

Ground

NC

SMB_CLK_R

Pin#

1

3

5

Pin#

2

4

6

Signal Name

NC

SMB_DATA_R

SOC-GPIO22

SOC-GPIO23

SOC-GPIO24

7

9

8

10

SOC-GPIO25

+5V

JTAG

(2.0mm Pitch 2x5 Pin Header), Reserve.

JP1

(2.0mm Pitch 1x2 Pin Header), Reserve.

JP2

(2.0mm Pitch 1x2 Pin Header), Reserve.

CAN1/CAN2

(3.5mm Pitch 1x10 Pin connector), it provides two CAN-bus Interface.

ARCHMI-8XX Series User Manual

58

Pin# Channel Signal Name

1

2

CANL2

R2-

3

4

7

8

5

6

CAN2

FG

R2+

CANH2

CANL1

R1-

FG

CAN bus Signal L

Function

Terminal resistor R-(internally connected to CANL2)

Shield cable (FG)

Terminal resistor R+(internally connected to CANH2)

CAN bus Signal H

CAN bus Signal L

CAN1

Terminal resistor R-(internally connected to CANL1)

Shield cable (FG)

9

10

R1+

CANH1

Terminal resistor R+(internally connected to CANH1)

CAN bus Signal H

【See TB-528AN2 Manual】

45. TB-528U2option:

SBC-7111 Riser Card,TB-528U2 CN3 connect to SBC-7111 CN3 pin Header.

TB-528U2 Top:

CN3

(1.27mm Pitch 2X30 Pin Header), connect to SBC-7111 CN3 pin Header.

USB23

(Double stack USB type A), Rear USB connector, it provides up to 2 USB2.0 ports, speed up to 480Mb/s.

ARCHMI-8XX Series User Manual

59

Chapter 3 BIOS Setup

3.1 Operations after POST Screen

After CMOS discharge or BIOS flashing operation,.Press [Delete] key to enter CMOS

Setup.

After optimizing and exiting CMOS Setup, the POST screen displayed for the first time is as follows and includes basic information on BIOS, CPU, memory, and storage devices.

3.2 BIOS Setup Utility

Press [Delete] key to enter BIOS Setup utility during POST, and then a main menu containing system summary information will appear.

ARCHMI-8XX Series User Manual

60

3.3 Main Settings

System Time:

Set the system time, the time format is:

Hour : 0 to 23

ARCHMI-8XX Series User Manual

Minute : 0 to 59

61

Second : 0 to 59

System Date:

Set the system date, the date format is:

Day: Note that the ‘Day’ automatically changes when you set the date.

Month: 01 to 12

Date: 01 to 31

Year: 1998 to 2099

3.4 Advanced Settings

3.4.1 ACPI Settings

Enable ACPI Auto Conf:

[Disabled]

[Enabled]

Enable Hibernation:

ARCHMI-8XX Series User Manual

62

[Enabled]

[Disabled]

ACPI Sleep State:

[S3 (Suspend to RAM) ]

[Suspend Disabled]

Lock Legacy Resources:

3.4.2 F81216SEC Super IO Configuration

Super IO chip F81216SEC

Serial Port 1 Configuration

[Disabled]

[Enabled]

UART1 Mode Selection:

[RS-232]

[RS-485]

[RS-422]

Serial Port 2 Configuration

Change Settings [Auto]

Serial Port 3 Configuration

Change Settings [Auto]

Serial Port 4 Configuration

Change Settings [Auto]

3.4.3 IT8518 Super IO Configuration

Super IO chip IT8518/IT8519

Serial Port 1 Configuration

Backlight PWM Controller(COM5):

[RS-485]

[RS-422]

Serial Port 2 Configuration (COM6)

Change Settings [Auto]

3.4.4 IntelRSmart Connect Technology

ISCT Support

[Disabled]

[Enabled]

ARCHMI-8XX Series User Manual

63

3.4.5 Serial Port Console Redirection

COM0

Console Redirection

[Disabled]

[Enabled]

Console Redirection Settings

Legacy Console Redirection

Legacy Console Redirection settings

Serial Port for Out-of-Band Management/

Windows Emergency Management Services (EMS)

Console Redirection

[Disabled]

[Enabled]

Console Redirection Settings

3.4.6 CPU Configuration

Socket 0 CPU Information

Intel(R) Atom(TM) CPU E3845 @ 1.91GHz

CPU Signature

Microcode Patch

Max CPU Speed

Mix CPU Speed

30679

901

1910 MHz

500 MHz

Processor Cores

Intel HT Technology

4

Not Supported

Intel HT-X Technology Supported

L1 Data Cache 24KB x 4

L1 Code Cache

L2 Cache

L2 Cache

32KB x 4

1024KB x 2

Not Present

CPU Thermal configuration

CPU Speed 1918 MHz

64-bit Supported

Hyper-Threading:

[Enabled]

[Disabled]

ARCHMI-8XX Series User Manual

64

Limit CPUID Maximum:

[Disabled]

[Enabled]

Execute Disable Bit:

[Enabled]

[Disabled]

Intel Virtualization Technology:

[Enabled]

[Disabled]

Power Technology

[Energy Efficient]

[Disabled]

[Custom]

3.4.7 PPM Configuration

CPU C State Report

[Enabled]

[Disabled]

Max CPU C-state

[C7]

[C6]

[C1]

SOix

[Disabled]

[Enabled]

3.4.8 Thermal Configuration Parameters

3.4.9 IDE Configuration

Serial-ATA(SATA)

[Enabled]

[Disabled]

SATA Test Mode

[Disabled]

[Enabled]

SATA Speed Support

[Gen2]

[Gen1]

ARCHMI-8XX Series User Manual

65

SATA ODD Port

[No ODD]

[Porto ODD]

[Port1 ODD]

[Disabled]

SATA Mode

[AHCI Mode]

[IDE Mode]

Serial-ATA Port 0

[Enabled]

[Disabled]

SATA Port0 Hotplug

[Disabled]

[Enabled]

Serial-ATA Port 1

[Enabled]

[Disabled]

SATA Port1 Hotplug

[Disabled]

[Enabled]

SATA Port0

Not Present

SATA Port1

Not Present

3.4.10 Miscellaneous Configuration

3.4.11 LPSS & SCC Configuration

LPSS & SCC Configuration

SCC Configuration

[ACPI Mode]

SCC eMMC Support [eMMC AUTO MODE]

SCC eMMC 4.5 DDR50 Support [Enabled]

SCC eMMC 4.5 HS200 Support [Disabled] eMMC Secure Erase [Disabled]

SCC SDIO Support

SCC SD Card Support

[Enabled]

[Enabled]

SDR25 Support for SDCard

SDR50 Support for SDCard

[Disabled]

[Enabled]

ARCHMI-8XX Series User Manual

66

MIPI HSI Support

LPSS Configuration

LPSS DMA #1 Support

LPSS DMA #2 Support

LPSS I2C #1 Support

LPSS I2C #2 Support

LPSS I2C #3 Support

[Disabled]

[Enabled]

[Enabled]

[Enabled]

[Enabled]

[Enabled]

[Enabled]

[Enabled]

LPSS I2C #4 Support

LPSS I2C #5 Support

LPSS I2C #6 Support

LPSS I2C #7 Support

NFC

Touch Pad

I2C touch Device Address

LPSS HSUART #1 Support

LPSS HSUART #2 Support

LPSS PWM #1 Support

LPSS PWM #2 Support

LPSS SPI Support

[Enabled]

[Enabled]

[Disabled]

[Disabled]

[Disabled]

[Disabled]

[Enabled]

[Enabled]

[Enabled]

3.4.12 System Component

3.4.13 Network Stack Configuration

Network Stack [Disabled]

3.4.14 CSM Configuration

CSM Support

CSM16 Module Version

GateA20 Active

Option ROM Messages

Boot option filter

Network

[Enabled]

07.76

[Upon Request]

[Always]

[Force BIOS]

[Keep Current]

[UEFI and Legacy]

[Legacy only]

[UEFI only]

[UEFI]

ARCHMI-8XX Series User Manual

67

Storage

Video

Other PCI devices

3.4.15 SDIO Configuration

3.4.16 USB Configuration

USB Configuration

USB Module Version 8.11.02

USB Devices:

1 keyboard, 1 Mouse,2 Hubs

Legacy USB Support:

[Enabled]

[Disabled]

XHCI Hand-off:

[Enabled]

[Disabled]

EHCI Hand-off:

[Disabled]

[Enabled]

USB Mass Storage Driver Support

[Enabled]

[Disabled]

USB hardware delays and time-outs:

USB transfer time-out:

[20 sec]

[10 sec]

[Do not launch]

[Legacy]

[UEFI]

[Do not launch]

[Legacy]

[Legacy]

[UEFI]

[Do not launch]

[UEFI]

[Do not launch]

[Legacy]

ARCHMI-8XX Series User Manual

68

Device reset time-out:

Device power-up delay

3.4.17 Platform Trust Technology

3.4.18 Security Configuration

3.5 Chipset Settings

[5 sec]

[1 sec]

[20 sec]

[10 sec]

[30 sec]

[40 sec]

[Auto]

[Manual]

3.5.1 Host Bridge

Intel IGD Configuration

IGD – LCD Control

Force Lid Status

ARCHMI-8XX Series User Manual

[On]

[Off]

69

BIA

ALS Support

IGD Flat Panel

Pannel Scaling

[Auto]

[Disabled]

[Auto]

[Auto]

Memory Frequency and Timing

Graphics Power Management Control

Memory Information

Total Memory

Memory Slot0

DIMM#1

Max TOLUD

4096 MB(DDR3L)

4096 MB(DDR3L)

Not Present

[Dynamic]

[2GB]

[2.25GB]

[2.5GB]

[2.75GB]

[3GB]

3.5.2 South Bridge

►Azalia HD Audio

►USB Configuration

USB OTG Support

USB VBUS

[Disabled]

[On]

XHCI Mode [Smart Auto]

USB2 Link Power Management [Enabled]

USB 2.0(EHCI) Support

USB EHCI debug

USB Per Port Control

USB Port 0

USB Port 1

USB Port 2

USB Port 3

[Enabled]

[Disabled]

[Enabled]

[Enabled]

[Enabled]

[Enabled]

[Enabled]

ARCHMI-8XX Series User Manual

70

3.6 Security Settings

3.6.1 Administrator Password

3.6.2 User Password

Type the password with up to 20 characters and then press Enter key. This will clear all previously typed CMOS passwords. You will be requested to confirm the password. Type the password again and press Enter key. You may press Esc key to abandon password entry operation.

To clear the password, just press Enter key when password input window pops up. A confirmation message will be shown on the screen as to whether the password

ARCHMI-8XX Series User Manual

71

will be disabled. You will have direct access to BIOS setup without typing any password after system reboot once the password is disabled.

Once the password feature is used, you will be requested to type the password each time you enter BIOS setup. This will prevent unauthorized persons from changing your system configurations.

Also, the feature is capable of requesting users to enter the password prior to system boot to control unauthorized access to your computer. Users may enable the feature in Security Option of Advanced BIOS Features. If Security Option is set to

System, you will be requested to enter the password before system boot and when entering BIOS setup; if Security Option is set to Setup, you will be requested for password for entering BIOS setup.

3.7 Boot Settings

Setup Prompt Timeout [1]

Bootup Numlock State

[On]

[off]

Quiet Boot

[Disabled]

ARCHMI-8XX Series User Manual

72

[Enabled]

Fast Boot

[Disabled]

[Enabled]

Boot Option Priorities

Boot Option #1

Sets the system boot order

Hard Drive BBS Priorities [SATA PM:*** … ]

Boot Option #1

SATA PM:***…

******

Disabled

3.8 Save & Exit Settings

Save Changes and Exit

Save & Exit Setup save Configuration and exit ?

[Yes]

[No]

ARCHMI-8XX Series User Manual

73

Discard Changes and Ext

Exit Without Saving Quit without saving?

[Yes]

[No]

Save Changes and Reset

Save & reset Save Configuration and reset?

[Yes]

[No]

Discard Changes and Reset

Reset Without Saving Reset without saving?

[Yes]

[No]

Save Changes

Save Setup Values Save configuration?

[Yes]

[No]

Discard Changes

Load Previous Values Load Previous Values?

Restore Defaults

Load Optimized Defaults Load optimized Defaults?

[Yes]

[No]

Save user Defaults

Save Values as User Defaults Save configuration?

[Yes]

[No]

[Yes]

[No]

Restore user Defaults

Restore User Defaults Restore User Defaults?

[Yes]

[No]

Launch EFI Shell from filesystem device

WARNING Not Found

[ok]

Reset System with ME disable ModeMEUD000

ME will runs into the temporary disable mode, Ignore if ME Ignition

FWMEUD001.

ARCHMI-8XX Series User Manual

74

Chapter 4 Installation of Drivers

This chapter describes the installation procedures for software and drivers under the windows 7. The software and drivers are included with the motherboard. The contents include Intel chipset driver, VGA driver, LAN drivers, Audio driver, USB 3.0

Driver Installation instructions are given below.

Important Note:

After installing your Windows operating system, you must install first the Intel

Chipset Software Installation Utility before proceeding with the installation of drivers.

ARCHMI-8XX Series User Manual

75

4.1 Intel(R) AtomTM SoC Chipset

To install the Intel chipset driver, please follow the steps below.

Step 1. Select Intel (R) AtomTM SoC Chipset from the list

Step 2. Click Next to setup program.

ARCHMI-8XX Series User Manual

76

Step 3. Read the license agreement. Click Yes to accept all of the terms of the license agreement.

Step 4. Click Next to continue.

ARCHMI-8XX Series User Manual

77

Step 5. Click Next.

Step 6. Select Yes, I want to restart this computer now. Click Finish, then remove any installation media from the drives.

ARCHMI-8XX Series User Manual

78

4.2 Intel(R) VGA Chipset

To install the VGA drivers, follow the steps below to proceed with the installation.

Step 1.Select Intel(R) VGA Chipset

Step 2. Click Automatically run WinSAT and enable the Windows Aero desktop

theme(if supported). Click Next.

ARCHMI-8XX Series User Manual

79

Step 3. Read license agreement. Click Yes.

Step 4. Click Next.

ARCHMI-8XX Series User Manual

80

Step 5. Click Install.

Step 6. Click Install.

ARCHMI-8XX Series User Manual

81

Step 7. Click Next.

Step 8. Click Yes, I want to restart this computer now. Then click Finish.

ARCHMI-8XX Series User Manual

82

4.3 Intel(R) LAN Driver

To install the Intel (R) LAN driver, please follow the steps below.

Step 1. Select Intel(R) 82574L LAN Driver from the list.

Step 2. . Click Next.

ARCHMI-8XX Series User Manual

83

Step 3. Read license agreement. Click I accept the terms in the license agreement.

Click Next.

Step 4. Click Next to continue.

ARCHMI-8XX Series User Manual

84

Step 5. Click Install to begin the installation.

Step 6. Click Finish to exit the wizard.

ARCHMI-8XX Series User Manual

85

4.4 Realtek ALC662 HD Audio Driver Installation

To install the Realtek ALC662 HD Audio Driver, please follow the steps below.

Step 1. Select Realtek AL662 HD Audio Driver from the list

Step 2. Click Next to continue.

ARCHMI-8XX Series User Manual

86

Step 3. Click Yes, I want to restart my computer now. Click Finish to complete the installation.

ARCHMI-8XX Series User Manual

87

4.5 USB 3.0 Driver

To install the USB 3.0 Driver, please follow the steps below.

Step 1. Select USB 3.0 Driver from the list

Step 2. Click Next to continue.

ARCHMI-8XX Series User Manual

88

Step 3. Read the license agreement. Then click Yes to continue.

Step 4. Click Next to continue.

ARCHMI-8XX Series User Manual

89

Step 5. Click Next to continue.

Step 6. Select Yes, I want to restart this computer now. Then click Finish to complete the installation.

ARCHMI-8XX Series User Manual

90

Chapter 5 Touch Screen Installation

This chapter describes how to install drivers and other software that will allow your touch screen work with different operating systems.

5.1 Windows XP/2003/Vista/WIN7 Universal Driver

Installation for PenMount 6000 Series

Before installing the Windows XP/2003/Vista/WIN7 driver software, you must have the Windows XP/2003/Vista/WIN7 system installed and running on your computer.

You must also have one of the following PenMount 6000 series controller or control boards installed: PM6500, PM6300.

5.1.1 Installing Software(Resistive Touch)

If you have an older version of the PenMount Windows WIN7 driver installed in your system, please remove it first. Follow the steps below to install the PenMount

DMC6000 Windows WIN7 driver.

Step 1. Insert the product CD, the screen below would appear. Click Touch Panel

Driver.

ARCHMI-8XX Series User Manual

91

Step 2. Select Resistive Touch.

Step 3. Click Next to continue.

ARCHMI-8XX Series User Manual

92

Step 4. Read the license agreement. Click I Agree to agree the license agreement.

Step 5. Choose the folder in which to install PenMount Windows Universal Driver.

Click Install to start the installation.

ARCHMI-8XX Series User Manual

93

Step 6. Wait for installation. Then click Next to continue.

Step 7. Click Continue Anyway.

ARCHMI-8XX Series User Manual

94

Step 8. Click Finish to complete installation.

5.1.2 Installing Software (Projected Capacitive)

Step 1. Insert the product CD, the screen below would appear. Click touch panel driver.

ARCHMI-8XX Series User Manual

95

Step 2. Select Projected Capacitive.

Step 3. Click Next to continue.

ARCHMI-8XX Series User Manual

96

Step 4. Select I accept the terms of the license agreement. Click Next.

Step 5. Click Install RS232 interface driver.

ARCHMI-8XX Series User Manual

97

Step 6. Select None. Click Next.

Step 7. Click OK.

Step 8. Click Support Muti-Monitor System. Click Next.

ARCHMI-8XX Series User Manual

98

Step 9. Go to C:\Program Files\eGalaxTouch. Click Next.

Step 10. Click Next.

ARCHMI-8XX Series User Manual

99

Step 11. Click Create a eGalaxTouch Utility shortcut on desktop. Click Next.

Step 12. Wait for installation.

Step 13. Click Yes to do 4 point calibration.

ARCHMI-8XX Series User Manual

100

5.2 Software Functions

5.2.1 Software Functions(Resistive Touch)

Upon rebooting, the computer automatically finds the new 6000 controller board.

The touch screen is connected but not calibrated. Follow the procedures below to carry out calibration.

1. After installation, click the PenMount Monitor icon “PM” in the menu bar.

2. When the PenMount Control Panel appears, select a device to “Calibrate.”

PenMount Control Panel(Resistive Touch)

The functions of the PenMount Control Panel are Device, Multiple Monitors ,Tools and About, which are explained in the following sections.

Device

In this window, you can find out that how many devices be detected on your system.

Calibrate

This function offers two ways to calibrate your touch screen. ‘Standard Calibration’ adjusts most touch screens. ‘Advanced Calibration’ adjusts aging touch screens.

ARCHMI-8XX Series User Manual

101

Standard Calibration Click this button and arrows appear pointing to red

squares. Use your finger or stylus to touch the red squares in sequence. After the fifth red point calibration

is complete. To skip, press ‘ESC’.

Advanced Calibration Advanced Calibration uses 4, 9, 16 or 25 points to

effectively calibrate touch panel linearity of aged touch screens. Click this button and touch the red squares in

sequence with a stylus. To skip, press ESC’.

Step 1. Please select a device then click “Configure”. You can also double click the device too.

ARCHMI-8XX Series User Manual

102

Step 2.Click “Standard Calibration” to start calibration procedure

NOTE: The older the touch screen, the more Advanced Mode calibration points you need for an accurate calibration. Use a stylus during Advanced Calibration for greater accuracy. Please follow the step as below:

ARCHMI-8XX Series User Manual

103

Step 3.Come back to “PenMount Control Panel” and select Tools then click Advanced Calibration.

Step 4. Select Device to calibrate, then you can start to do Advanced Calibration.

NOTE: Recommend to use a stylus during Advanced Calibration for greater accuracy.

ARCHMI-8XX Series User Manual

104

Plot Calibration Data

Check this function and a touch panel linearity comparison graph appears when you have finished

Advanced Calibration. The blue lines show linearity before calibration and black lines show linearity after calibration.

Turn off EEPROM storage

The function disable for calibration data to write in

Controller. The default setting is Enable.

Setting

Touch Mode

Beep Sound

This mode enables and disables the mouse’s ability to drag on-screen icons – useful for configuring POS terminals.

Mouse Emulation – Select this mode and the mouse functions as normal and allows dragging of icons.

Click on Touch – Select this mode and mouse only provides a click function, and dragging is disables.

Enable Beep Sound – turns beep function on and off

Beep on Pen Down – beep occurs when pen comes down

Beep on Pen Up – beep occurs when pen is lifted up

Beep on both – beep occurs when comes down and lifted up

Beep Frequency – modifies sound frequency

Beep Duration – modifies sound duration

Cursor Stabilizer

Enable the function support to prevent cursor shake.

Use press and

You can set the time out and area for you need.

hold as right click

ARCHMI-8XX Series User Manual

105

About

This panel displays information about the PenMount controller and driver version.

ARCHMI-8XX Series User Manual

106

Multiple Monitors

Multiple Monitors support from two to six touch screen displays for one system. The

PenMount drivers for Windows XP/2003/Vista/WIN7 support Multiple Monitors. This function supports from two to six touch screen displays for one system. Each monitor requires its own PenMount touch screen control board, either installed inside the display or in a central unit. The PenMount control boards must be connected to the computer COM ports via the USB interface. Driver installation procedures are the same as for a single monitor. Multiple Monitors support the following modes:

Windows Extends Monitor Function

Matrox DualHead Multi-Screen Function nVidia nView Function

NOTE: The Multiple Monitor function is for use with multiple displays only. Do not use this function if you have only one touch screen display. Please note once you turn on this function the rotating function is disabled.

Enable the multiple display function as follows:

1. Check the Enable Multiple Monitor Support box; then click Map Touch Screens to assign touch controllers to displays.

ARCHMI-8XX Series User Manual

107

2. When the mapping screen message appears, click OK.

3. Touch each screen as it displays “Please touch this monitor”. Following this sequence and touching each screen is called mapping the touch screens.

4. Touching all screens completes the mapping and the desktop reappears on the monitors.

5. Select a display and execute the “Calibration” function. A message to start calibration appears. Click OK.

ARCHMI-8XX Series User Manual

108

6. “Touch this screen to start its calibration” appears on one of the screens. Touch the screen.

7. “Touch the red square” messages appear. Touch the red squares in sequence.

8. Continue calibration for each monitor by clicking Standard Calibration and touching the red squares.

NOTES:

1. If you use a single VGA output for multiple monitors, please do not use the

Multiple Monitor function. Just follow the regular procedure for calibration on each of your desktop monitors.

2. The Rotating function is disabled if you use the Multiple Monitor function.

3. If you change the resolution of display or screen address, you have to redo Map

Touch Screens, so the system understands where the displays are.

About

This panel displays information about the PenMount controller and this driver version.

PenMount Monitor Menu Icon

The PenMount monitor icon (PM) appears in the menu bar of Windows

XP/2003/Vista/WIN7 system when you turn on PenMount Monitor in PenMount

Utilities.

ARCHMI-8XX Series User Manual

109

PenMount Monitor has the following function

Control Panel

Open Control Panel Windows

Beep

Setting Beep function for each device

Right Button

Exit

When you select this function, a mouse icon appears in the right-bottom of the screen.

Click this icon to switch between Right and Left Button functions.

Exits the PenMount Monitor function.

Configuring the Rotate Function

1. Install the rotation software package.

2. Choose the rotate function (0°, 90°, 180°, 270°) in the 3rd party software. The calibration screen appears automatically. Touch this point and rotation is mapped.

NOTE: The Rotate function is disabled if you use Monitor Mapping

ARCHMI-8XX Series User Manual

110

5.2.2 Software Functions(Projected Capacitive)

General

In this window, you can see there is USB Controller. Click OK to continue.

ARCHMI-8XX Series User Manual

Monitor Mapping

to adjust touch panel

Add

to search for device

111

Setting

Beep

Beep On Touch

Beep On Release

Beep From System Beep

Beep From Sound Card

Linearization Style

9 points

25 points

Double Click Time

Shorter

Longer

Double Click Area

Smaller

Bigger

Normal mode

Simulate the mouse mode

ARCHMI-8XX Series User Manual

112

Option

Function

Enable Constant Touch

Enable Auto Right Click

Enable Touch

Enable Cursor Stabilization

Constant Touch Area

Auto Right Click Time

ARCHMI-8XX Series User Manual

113

Tools

Click OK to continue the settings.

4 Points Calibration

Do 4 points alignment to match display.

Clear and Calibrate

Clear linearization parameter and do 4 points alignment.

Linearization

Do 9 points linearization for better touchscreen linearity.

Draw Test

Do draw test to verify the touch accuracy.

ARCHMI-8XX Series User Manual

114

Display

In this window, it shows the mode of display.

Enable Multiple Monitors.

Map to main display if system has only one display monitor

Full Screen

Lower Screen

Left Screen

Upper Screen

Right Screen

ARCHMI-8XX Series User Manual

115

Other

Other mode of display. Quarter1~4 and Customized area.

Active Area

Drag active area to enable Active Area Function.

ARCHMI-8XX Series User Manual

116

Hardware

Saturn Hardware Configuration

ARCHMI-8XX Series User Manual

117

About

To display information about eGalaxTouch and its version.

ARCHMI-8XX Series User Manual

118

advertisement

Related manuals

Download PDF

advertisement