PLANET FRT-420SN User's manual

Add to My manuals
80 Pages

advertisement

PLANET FRT-420SN User's manual | Manualzz

802.11n Wireless VoIP

Fiber Router

FRT-420SN

Copyright

Copyright (C) 2012 PLANET Technology Corp. All rights reserved.

The products and programs described in this User’s Manual are licensed products of PLANET Technology, This

User’s Manual contains proprietary information protected by copyright, and this User’s Manual and all accompanying hardware, software, and documentation are copyrighted.

No part of this User’s Manual may be copied, photocopied, reproduced, translated, or reduced to any electronic medium or machine-readable form by any means by electronic or mechanical. Including photocopying, recording, or information storage and retrieval systems, for any purpose other than the purchaser's personal use, and without the prior express written permission of PLANET Technology.

Disclaimer

PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose.

PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for any inaccuracies or omissions that may have occurred.

Information in this User’s Manual is subject to change without notice and does not represent a commitment on the part of PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User’s

Manual. PLANET makes no commitment to update or keep current the information in this User’s Manual, and reserves the right to make improvements to this User’s Manual and/or to the products described in this User’s

Manual, at any time without notice.

If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your comments and suggestions.

CE mark Warning

The is a class B device, In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

WEEE Warning

To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of

WEEE as unsorted municipal waste and have to collect such WEEE separately.

Trademarks

The PLANET logo is a trademark of PLANET Technology. This documentation may refer to numerous hardware and software products by their trade names. In most, if not all cases, their respective companies claim these designations as trademarks or registered trademarks.

Revision

User’s Manual for PLANET 802.11n Wireless VoIP Fiber Router:

Model: FRT-420SN

Rev: 1.0 (2012, April)

Part No. EM-FRT-420SN_v1

TABLE OF CONTENTS

Chapter 1 Introduction..............................................................................................5

Overview .............................................................................................................5

Package Content ................................................................................................6

Physical Details ..................................................................................................7

Physical Interface & Button.................................................................................................... 7

Chapter 2 Preparations & Installation......................................................................9

Physical Installation Requirement ....................................................................9

Keypad commands .............................................................................................................. 10

Chapter 3 Network Settings ...................................................................................13

Configuring and monitoring your Router from web browser.......................13

Overview on the web interface of Router............................................................................. 13

Manipulation of Router via web browser.............................................................................. 13

Network Oprtation Mode ...................................................................................................... 14

WAN Interface Setup ........................................................................................................... 15

LAN Interface Setup............................................................................................................. 20

Chapter 4 Wireless Settings ...................................................................................22

Basic Settings ...................................................................................................................... 22

Advanced Settings ............................................................................................................... 24

Security Setup...................................................................................................................... 26

Access Control ..................................................................................................................... 29

WDS Settings....................................................................................................................... 29

Site Survey........................................................................................................................... 30

WPS Settings ....................................................................................................................... 30

Wireless Schedule ............................................................................................................... 33

Chapter 5 Firewall Settings ....................................................................................34

Port Filtering......................................................................................................................... 34

IP Filtering ............................................................................................................................ 34

MAC Filtering ....................................................................................................................... 35

Port Forwarding.................................................................................................................... 36

URL Filtering ........................................................................................................................ 36

DMZ ..................................................................................................................................... 37

QoS ...................................................................................................................................... 37

Chapter 6 SIP Settings ............................................................................................38

Phone 1 / Phone 2 ............................................................................................................... 38

Tone ..................................................................................................................................... 48

Other .................................................................................................................................... 50

SIP QoS ............................................................................................................................... 51

Chapter 7 Management...........................................................................................52

Status ................................................................................................................................... 52

Statistics ............................................................................................................................... 52

DDNS ................................................................................................................................... 53

Time Zone Setting................................................................................................................ 54

Denial-of-Service.................................................................................................................. 54

SNMP Management............................................................................................................. 55

Log ....................................................................................................................................... 56

Upgrade Firmware ............................................................................................................... 57

Auto Config .......................................................................................................................... 57

Save / Reload Settings ........................................................................................................ 59

Password Setup................................................................................................................... 60

Chapter 8 Fiber Setting...........................................................................................62

Fiber configuration ............................................................................................................... 62

Chapter 9 Utility.......................................................................................................63

Ping Watchdog Setup .......................................................................................................... 62

Ping Test .............................................................................................................................. 62

Traceroute............................................................................................................................ 63

Reboot.................................................................................................................................. 63

Logout .................................................................................................................................. 63

Appendix A Voice communication samples...................................................64

Peer to peer (P2P) mode ..................................................................................................... 64

Case 2: (Peer-to-Peer mode) FRT-420SN Port 1 to Port 2 communications ...................... 65

Case 3: SIP Proxy mode...................................................................................................... 66

Case 4: Call Forward Feature.............................................................................................. 70

Case 5: FRT-420SN register with IPX-1900 via WAN port.................................................. 71

Case 6: FRT-420SN register with UMG-2000 via WAN port ............................................... 74

Appendix B The method of featured voice operation guide.........................76

Call Transfer......................................................................................................................... 76

3-Way Conference ............................................................................................................... 76

Call Waiting .......................................................................................................................... 76

Switch the Default Proxy...................................................................................................... 76

Auto Update firmware by manual (Keypad)......................................................................... 77

Appendix C Frequently Asked Questions List...............................................78

Appendix D Router Specifications..................................................................80

Chapter 1

Introduction

Overview

Integrating the cutting edge of Internet Telephony and VoIP Router manufacturing experience, PLANET now introduces the latest member of PLANET Wireless VoIP Router family: the FRT-420SN.

With growing network services such as HDTV, IPTV, voice-over-IP (VoIP) and Multimedia broadband applications, and the demand of bandwidth rises quickly. The current Broadband environment has not already accorded with needing; the FTTH (fiber-to-the-home) would be the most promising NGN (Next

Generation Networking) application to fulfill the demand.

The PLANET Internet Fiber Router, FRT-420SN provides office and residential users the ideal solution for sharing a high-speed fiber Internet connection and four-10/100Mbps Fast Ethernet backbone. The

Fiber Router is a perfect FTTH Digital Home Router which can provide very high performance access to Internet, both downstream and upstream up to 100Mbps through the fiber interface. The PLANET

FRT-420SN supports one SFP optical connectors for WAN connection. The Fiber Router can be implemented easily for optical fiber deployment.

The FRT-420SN provides not only high-quality voice communications and wired Internet sharing capabilities but also the Access Point (AP) function for flexible wireless communication. With advanced router and VoIP DSP processor technology, the FRT-420SN is able to make calls via SIP proxy voice communications plus the IP sharing and the QoS mechanism.

By applying the FRT-420SN, home users and companies are able to save installation cost and extend the VoIP network from their previous investments in telephones, conferences and speakerphones. The

FRT-420SN is equipped with two telephony interfaces, so users may register to different SIP proxy servers and establish up to 2 concurrent VoIP calls for more flexibility in the voice communications. The

FRT-420SN can also be the bridge between traditional analog telephones and IP network with an extremely affordable investment.

With built-in IEEE 802.11b/g/n wireless network capability, the FRT-420SN allows any computer and wireless enabled network client connect to it without additional cabling. The 802.11n wireless capability gives users the highest speed of wireless experience ever. With an 802.11n compatible wireless adapter installed in your PC, the files can be transferred at up to 300Mbps. The radio coverage is also doubled to offer the high speed wireless connection even in a wide space of your office or house.

To secure the wireless communication, the FRT-420SN supports most up-to-date encryption: WEP,

WPA-PSK and WPA2-PSK. In addition, the FRT-420SN supports WPS configuration with PBC/PIN type for users to connect to a secured wireless network easily.

Product Features

• Fiber Interface support

• Long distance connection based on optical fiber transceiver

• Complies with IEEE 802.3, IEEE 802.3u 10/100Base-TX, 100Base-FX standard

• Co-work with PLANET 100Base-FX Media Conversion

• Smart QoS mechanism to ensure the voice quality

• NAT Router, Port Forwarding, DMZ

• IP ToS (IP Precedence) / DiffServ

• Voice prompt for machine configurations

• Supports FTTH / IPTV applications

Wireless Features

• IEEE 802.11b/g/n wireless standard compliant

• Multi-mode: AP, AP-Client Mode

• Supports 64/128-bit WEP, WPA, WPA-PSK, WPA2, WPA2-PSK and 802.1x encryption

VoIP Features

• SIP 2.0 (RFC3261) compliant

• Up to 2 concurrent VoIP calls

• Voice codec support: G.711, G.729AB, G.723, G.276, GSM and G.722

• T.38 FAX transmission over IP network (G.711 Fax pass-through)

• In-band and out-of-band DTMF Relay (RFC 2833)

• 3-Way conference calls

• Call Waiting / Forward / Transfer / Hold / Resume

• Caller ID Detection / Generation: DTMF, BELLCORE, ETSI, BT, NTT

• Voice processing: VAD, CNG, Dynamic Jitter Buffer, G.168 Line Echo Cancellation

• SNMP v1/v2 and Auto Provision management

• Auto-Provision feature for flexible, ease-of use system integration

Package Content

The contents of your product should contain the following items:

802.11n Wireless VoIP Fiber Router

Power adapter

Quick Installation Guide

User’s Manual CD

RJ-11 cable x 2

Antenna x2

Physical Details

The following figure illustrates the each panel of FRT-420SN

Front Panel

Rear Panel

Physical Interface & Button

Front Panel LED Indicators

LED

PWR

WAN

LAN

WPS

WLAN

Phone

State

ON

Off

ON

Flashing

Off

ON

Flashing

Off

ON

Off

Flashing

Off

ON

Flashing

Off

Reset Button

WPS Button

Descriptions

Router is power ON

Router is power Off

Router network connection established

Data traffic on cable network

Waiting for network connection

LAN is connected successfully

Data is transmitting

Ethernet not connected to PC

The Wi-Fi Protected Setup function is starting.

The Wi-Fi Protected Setup function is close

Transmitting or receiving data through the Wireless LAN

Wireless LAN is no function

Telephone Set is On-Hook

Ring Indication

Telephone Set is Off-Hook

- Pressing 1 second to reboot machine.

- Pressing 5 seconds to reset to the factory default setting

- Pressing 3 seconds to start the WPS function 2 minutes for client connection.

- Pressing 10 seconds to enable or disable the wireless function.

Rear Panel Indicators

FIBER SPECIFICATIONS

Product

WAN

Ports

LAN

Optic

Interface

Fiber-optic cable

Internet Fiber Router

1 x 100Base-FX port

4 x 10/100Base-TX port

Connector SFP

Mode Vary on module

Distance Vary on module

ƒ 9/125μm single-mode cable, provide long distance for

15/20/35/50km or longer (very on SFP module)

2 LAN

RJ-45 connector, to maintain the existing network structure, connected directly to the PC through straight CAT-5 cable

4 12V DC

12V DC Power input outlet

Used to connect the external antenna for accessing to 802.11b/g/n

5 Antenna

wireless network

Í

Note

1. Machine LAN port default IP is http://192.168.0.1

. Press

RESET

button on front panel over 5 seconds will reset the

VoIP Router to factory default value. (Except speed dial and call forward settings)

2. Using the power supply that is not the one included in package will cause damage and void the warranty for this product.

Chapter 2

Preparations & Installation

2

Physical Installation Requirement

This chapter illustrates basic installation of Wireless VoIP Fiber Router (“Router” in the following term)

• Network cables. One Fiber-optic Interface, SC connector-type

• TCP/IP protocol must be installed on all PCs.

For Internet Access, an Internet Access account with an ISP, and either of a DSL or Cable modem

Administration Interface

PLANET Router provides GUI (Web based, Graphical User Interface) and utility for machine management and administration.

Web configuration access

You will connect to SIP Router via your web browser automatically. Router will prompt for logon username / password, please enter: admin / admin to continue machine administration.

Router will prompt for logon username/password, please enter: admin / admin to continue machine administration.

The default IP address of LAN port is 192.168.0.1. (The WAN port is DHCP client mode.) You also could open your web browser, and insert http://192.168.0.1 in the address bar of your web browser to logon Router web configuration page.

To start Router web configuration, you must have one of these web browsers installed on computer for management

Microsoft Internet Explorer 6.00 or higher with Java support

Í

Note

Please locate your PC in the same network segment

(192.168.0.x) of Router. If you’re not familiar with TCP/IP , please refer to related chapter on user’s manual CD or consult your network administrator for proper network configurations.

Keypad commands

The Router series phone adapters support telephone keypad configurations, please connect analog telephone set and refer to the following table for machine network configurations.

IVR Menu Choice

#111#

#112xxx*xxx*xxx* xxx#

#113xxx*xxx*xxx* xxx#

#114xxx*xxx*xxx* xxx#

#115xxx*xxx*xxx* xxx#

#190#

#195#

Machine operation

Set DHCP client

Setup Static IP Address

Set Network Mask

Set Gateway IP Address

Set Primary DNS Server

Unlock

Save Network Settings

Parameter(s)

None

Notes

WAN port will change to

DHCP Client

Use the * (star) key when entering a decimal point.

Use the * (star) key when entering a decimal point.

DHCP will be disabled and system will change to the

Static IP type.

Must set Static IP first.

Use the * (star) key when entering a decimal point.

Must set Static IP first.

Use the * (star) key when entering a decimal point.

Must set Static IP first.

None

None

Must unlock the protect function before carry out the firmware update

(#160#).

Must save network settings after set up network settings via keypad.

#198#

Factory Reset None

The system will be reset to factory default value and reboot automatically.

Following keypad commands can be used to display the network settings enabled on Router via voice prompt.

IVR Menu Choice

#120#

#126#

#121#

#122#

#123#

#124#

#125#

Machine operation

Check LAN port IP Address

Check WAN port IP Address

Check network connection Type

Check the Phone Number

Check Network Mask

Check Gateway IP Address

Check DNS Server Setting

Notes

IVR will announce the current IP address of the LAN port.

IVR will announce the current IP address of the WAN port.

IVR will announce if DHCP in enabled or disabled. (WAN port)

IVR will announce current enabled VoIP number. (WAN port)

IVR will announce the current network mask of the Router. (WAN port)

IVR will announce the current gateway IP address of the Router. (WAN port)

IVR will announce the current setting in the

DNS field. (WAN port)

#128#

Check Firmware Version

IVR will announce the version of the firmware running on the Router.

Following keypad commands can be used to set up the main function .

IVR Menu Choice

#130+first priority codec

#133#

#134#

#138#

#139#

#140+Forward type+Forward

Phone Number#

#141#

Machine operation

Set First Priority Codec

Set Speaker Voice Gain

Set Mic Voice Gain

Parameter(s)

01: G.711 u-Law, 02:

G.711 a-Law, 03: G.729,

04: G.723 6.3K, 05:

G.723 5.3K, 06: G.726

16K, 07: G.726 24K, 08:

G.726 32K, 09: G.726

40K, 10: GSM-FR, 11:

G.722

Notes

You can set the codec you want to the first priority.

For example: #13001#

Set G.711 u-Law to the first priority codec

00~31, 32: Mute

00~31, 32: Mute

For example: #13305#

Mic Voice: 5

For example: #13410#

Mic Voice: 10

Enable Call waiting

Disable Call waiting

Enable call waiting

Disable call waiting

None

None

Forward Settings

Forward Type:

1: Immediate Forward

2: Busy Forward

3: No answer Forward

Disable Forward Settings None

For example: #1401101#

Immediate Forward to 101

#150#

#160#

Select Default Realm

Update firmware

0: Realm 1, 1: Realm 2

None

For example: #1501#

Set Default Proxy to Realm 2

Update firmware

Must unlock the protect function (#190#) before carry out the firmware update.

Chapter 3

3

Network Settings

Configuring and monitoring your Router from web browser

The Router integrates a web-based graphical user interface that can cover most configurations and machine status monitoring. Via standard web browser, you can configure and check machine status from anywhere around the world.

Overview on the web interface of Router

With web graphical user interface, you may have:

Š More comprehensive setting feels than traditional command line interface.

Š Provides user input data fields, check boxes, and for changing machine configuration settings

Š Displays machine running configuration

To start Router web configuration, you must have one of these web browsers installed on computer for management

Š Microsoft Internet Explorer 6.00 or higher with Java support

Manipulation of Router via web browser

Log on Router via web browser

After TCP/IP configurations on your PC, you may now open your web browser, and input http://192.168.0.1

(Default LAN port IP address) to logon Router web configuration page.

Enter the IP address of the Router which by default is 192.168.0.1

Phone Adapter will prompt for logon username/password: admin / admin

Router login prompt screen

When users login the web page, users can see the general information like company…etc in this main page.

VoIP Router main page

Network Oprtation Mode

You can setup different modes to WAN and LAN interface for NAT, Bridging and Wireless ISP function

NAT

Bridge

Wireless ISP

In this mode, the device is supposed to connect to internet via

ADSL/Cable Modem. The NAT is enabled and your PC in LAN port shares the same IP to ISP through WAN port. The connection type can be setup in WAN page by using PPPOE, DHCP client, PPTP client, static IP or L2TP.

In this mode, all Ethernet ports are bridged together and NAT function is disabled. All the LAN port related function and firewall are not supported.

In this mode, all Ethernet ports are bridged together and the wireless client will connect to ISP access point. The NAT is enabled and PCs in

Ethernet ports share the same IP to ISP through wireless LAN. You must set the wireless to client mode first and connect to the ISP AP in

Site-Survey page. The connection type can be setup in WAN page by using PPPOE, DHCP client, PPTP client, static IP or L2TP.

WAN Interface Setup

This page is used to configure the parameters for Internet network which connects to the WAN port of your Gateway. Here you may change the access method to static IP, DHCP, PPPoE, PPTP or L2TP by click the item value of WAN Access type.

Connection Type Description –

Static IP

Static IP

IP Address

Subnet Mask

Default Gateway

MTU Size

DNS1/ 2/ 3

Clone MAC Address

Enable UPnP

Set WAN interface as Static IP mode.

WAN IP Address of the Router

Default :

192.168.0.1

WAN mask of the Router

Default :

255.255.255.0

Gateway Address of the Router

Default :

192.168.0.254

Set MTU (maximum transmission unit) size

Default :

1412

Set three alternatives Domain Name Server for WAN interface.

Default :

Null

To clone the MAC by manual input.

Default :

000000000000 (Null)

Check to enable UPnP function

Default :

Disable

Check to enable the IGMP Proxy function

Enable IGMP Proxy

Default :

Enable

If accept ICMP response via WAN port

Enable Ping Access on WAN

Default :

Enable

Enable IPSec pass through on

If accept be accessed to Web Management Interface via WAN

VPN connection

port

Default :

Enable

Enable PPTP pass through on

Check to enable PPTP pass through function

VPN connection

Default :

Disable

Enable L2TP pass through on

Check to enable L2TP pass through function

VPN connection

Default :

Disable

Connection Type Description – DHCP Client

DHCP Client

Set WAN interface as DHCP mode.

Attain DNS Automatically /

Select to attain DNS automatically from server or user wants to

Set DNS Manually

set DNS manually.

Default :

Set DNS Manually

Connection Type Description – PPPoE

PPPoE

User Name

Password

Service Name

Set WAN interface as PPPoE mode.

Set user name of PPPoE connection

Default :

Null

Set password of PPPoE connection

Default :

Null

Set Service Name of PPPoE for description

Connection Type

Idle Time

Default :

Null

Set PPPoE connection type to be Continuous/ Connect on Demand/

Manual. If user set type as Continuous, Router will keep trying to connect to server when PPPoE disconnect. If user set type as Connect on Demand, please set following idle time, Router will check connection after this time. If user set type as Manual, Router will only connect or disconnect by press Connect or Disconnect manually.

Default :

Continuous

Set PPPoE connection idle time for Connect on Demand.

Default :

5

After confirming the modification you’ve done, please click on the Apply button to apply settings effective and the Router will be reload page automatic by itsely, that you must to afresh enter the final modification IP address for logon web management.

Connection Type Description – PPTP/L2TP

PPTP

Mode

IP Address

Subnet Mask

Gateway

Server IP Address

User Name

Password

Set LAN interface as PPTP/L2TP mode.

Set IP type if Dynamic IP or Static IP at PPTP/L2TP connection.

Default :

Dynamic IP

WAN IP Address of the Router at Static IP type.

Default :

0.0.0.0

WAN Mask of the Router at Static IP type.

Default :

0.0.0.0

Gateway of the Router

Default :

0.0.0.0

Set PPTP/L2TP Server IP address.

Default :

0.0.0.0

Set user name of PPTP/L2TP connection

Default :

Null

Set password of PPTP/L2TP connection

Default :

Null

Í

Note

Please be noticed that the Utility Tool is only designed for the WAN environment setting. If the “Connect Type” is

PPPoE”, the Utility Tool can NOT find the device.

LAN Interface Setup

This page is used to configure the parameters for local area network which connects to the LAN port of your Gateway. Here you may change the setting for IP address, subnet mask, DHCP, etc..

IP Address

Subnet Mask

DHCP Server

DHCP Client Range

Static DHCP

LAN IP Address of the Router

Default :

192.168.0.1

LAN mask of the Router

Default :

255.255.255.0

You can select Server or Disable. If you select Disable, the

DHCP service of LAN port is disabled.

Default :

Server

The first and last IP address that DHCP server assigns.

Default :

192.168.0.100 – 192.168.0.200

It allows you reserve IP addresses, and assign the same IP address to the network device with the specified MAC address any time it requests an IP address

Default :

Disable

Domain Name

802.11d Spanning Tree

Port Bandwidth Manager

(WAN / LAN ports)

Set three alternatives Domain Name Server for LAN interface.

Default :

Null

Spanning Tree Protocol. You can select Enable or Disable.

Default :

Disable

Show the egress and ingress total network traffic for each WAN and LAN ports

Default :

0

Chapter 4

4

Wireless Settings

Basic Settings

This page is used to configure the parameters for wireless LAN clients who may connect to your

Access Point. Here you may change wireless encryption settings as well as wireless network parameters.

Disable Wireless LAN

Interface

Band

Enable or disable the wireless LAN.

There are 6 modes: 2.4GHz (B), 2.4GHz (G), 2.4GHz (N), 2.4GHz

(B+G), 2.4GHz (G+N), and 2.4GHz (B+G+N) mode.

Default :

2.4GHz (B+G+N)

Mode

Network Type -

SSID

Channel Width

Control Sideband

Channel Number

Broadcast SSID

- AP: The AP functions as a wireless hub to which wireless clients can connect. The clients must make sure that they are configured to match the AP’s wireless settings. The AP must be connected to switch or other LAN segment patch cable.

- Client: In this mode the Router is used to access the Wireless

Service Provider network by connecting wirelessly to the remote

(Outdoor AP).

- WDS: WDS operation as defined by the IEEE802.11 standard has been made available. Using WDS it is possible to wirelessly connect Access Points, and in doing so extend a wired infrastructure to locations where cabling is not possible or inefficient to implement.

- AP+WDS: It means the device can support WDS and AP Mode simultaneously.

Default :

AP mode

- Infrastructure: The wireless LAN serves as a wireless station

(infrastructure). Connected to a PC or a small LAN (no more than 5

PCs), it allows the PC or small LAN able to access the wireless network via Access Point.

- Ad hoc: The wireless LAN will use the Ad hoc mode to operate.

Wireless stations associating to the access point must have the same SSID. Enter a descriptive name for the wireless LAN.

Default :

802.11bgn-SSID

There are 20MHz and 40MHz bandwidths for cohesion

Default :

20MHz

Specify if the extension channel should be in the Upper or Lower sideband

Default :

Upper (Unavailable)

Select the appropriate channel from the list provided to correspond with your network settings. Channels differ from country to country.

Default :

6

If you enable “Broadcast ESSID”, every wireless station located within the coverage of this access point can discover this Router easily. If you are building a public wireless network, enabling this feature is recommended. In private network, disabling “Broadcast

ESSID” can provide better security.

Default :

Enable

WMM

Data Rate

The short of Wi-Fi Multi-Media, it will enhance the data transfer performance of multimedia contents when they’re being transferred over wireless network.

Default :

Enable (Unavailable)

The Data Rate is the rate of data transmission for 802.11b/g/n clients. The Router will use the highest possible selected transmission rate to transmit the data packets.

Default :

Auto

Default :

Auto

Associated Clients

Enable Mac Clone

Enable Universal

Repeater Mode

SSID of Extended

Interface

To show the MAC address, transmission, reception packet counters and encrypted status for each associated wireless client.

When set at Client mode, it provides wireless LAN to connect to a

MAC address.

Default :

Disable

Universal Repeater is a technology used to extend wireless coverage.

Default :

Disable

Click on “Enable Universal Repeater Mode”; In the “SSID of

Extended Interface”, enter the SSID of the wireless router that you want to extend.

Default :

Null

Advanced Settings

These settings are only for more technically advanced users who have a sufficient knowledge about wireless LAN. These settings should not be changed unless you know what effect the changes will have on your Access Point.

Fragment Threshold

RTS Threshold

Beacon Interval

Preamble Type

“Fragment Threshold” specifies the maximum size of packet during the fragmentation of data to be transmitted. If you set this value too low, it will result in bad performance.

Default :

2346

When the packet size is smaller the RTS threshold, the access point will not use the RTS/CTS mechanism to send this packet.

Default :

2347

The interval of time that this access point broadcast a beacon.

Beacon is used to synchronize the wireless network.

Default :

100

Preamble type defines the length of CRC block in the frames during the wireless communication. “Short Preamble” is suitable for high traffic wireless network. “Long Preamble” can provide more reliable communication.

Default :

Long Preamble

IAPP

Protection

Aggregation

Short GI

WLAN Partition

RF Output Power

Inter-Access Point Protocol is a recommendation that describes an optional extension to IEEE 802.11 that provides wireless access-point communications among multivendor systems.

Default :

Enable

It is recommended to enable the protection mechanism. This mechanism can decrease the rate of data collision between 802.11b and 802.11g wireless stations. When the protection mode is enabled, the throughput of the AP will be a little lower due to many of frame traffic should be transmitted.

Default :

Enable

It is a function where the values of multiple rows are grouped together.

Default :

Enable

It is used to set the time that the receiver waits for RF reflections to settle out before sampling data.

Default :

Enable

This feature also called WLAN isolation or Block Relay. If this feature is disabled, then there is no barrier between communications among wireless stations connecting to the Access Point, i.e the Router. If this is enabled, wireless stations of the selected band are not allowed to exchange data through the Access Point. The default value is set to 'Disabled'.

Default :

Disable

Users can adjust the output power to 100%, 75% 50% 35% and

15%.

Default :

100%

Security Setup

This page allows you setup the wireless security. Turn on WEP or WPA by using Encryption Keys could prevent any unauthorized access to your wireless network.

Select SSID

Encryption

802.1x Authentication

If assigned multiple AP feature, you could choose the SSID that want to setup encryption function.

Select the data privacy algorithm you want. Enabling the security can protect your data while it is transferred from one station to another.

Default :

Disable

Check Box was used to switch the function of the 802.1X. When the

802.1X function is enabled, the Wireless user must authenticate to this router first to use the Network service.

Default :

Uncheck

- WEP

When you select the 128 or 64 bit WEP key security, please select one WEP key to be used and input

26 or 10 hexadecimal (0, 1, 2…8, 9, A, B…F) digits.

- WPA

When select the WPA function, the Wireless user must authenticate to this router first to use the

Network service. RADIUS Server IP address or the 802.1X server’s domain-name.

If you select HEX, you have to fill in 64 hexadecimal (0, 1, 2…8, 9, A, B…F) digits

If ASCII, the length of pre-share key is from 8 to 63.

Key value shared by the RADIUS server and this router. This key value is consistent with the key value in the

RADIUS server.

- WPA2

When sele ct the WPA function, the Wireless user must authenticate to this router first to use the

Network service. RADIUS Server IP address or the 802.1X server’s domain-name.

If you select HEX, you have to fill in 64 hexadecimal (0, 1, 2…8, 9, A, B…F) digits

If ASCII, the length of Pre-share key is from 8 to 63.

Key value shared by the RADIUS server and this rou ter. This key value is consistent with the key value in the

RADIUS server.

WPA-Mixed

When select the W PA-Mixed function, the Wireless user must authenticate to this router first to use the

Network service. RADIUS Server

The router will detect automatically wh ich Security type (WPA-PSK version 1 or 2) the client uses to encrypt.

IP address or the 802.1X server’s domain-name.

If you select HEX, you have to fill in 64 hexadecimal (0, 1, 2…8, 9, A, B…F) digits

If ASCII, the length of Pre-share key is from 8 to 63.

Key value shared by the RADIUS server and this rou ter. This key value is consistent with the key value in the

RADIUS server.

Access Control

If you choose 'Allowed Listed', only those clients whose wireless MAC addresses are in the access control list will be able to connect to your Access Point. When 'Deny Listed' is selected, these wireless clients on the list will not be able to connect the Access Point.

WDS Settings

Wireless Distribution System uses wireless media to communicate with other APs, like the Ethernet does. To do this, you must set these APs in the same channel and set MAC address of other APs which you want to communicate with in the table and then enable the WDS.

Site Survey

This page provides tool to scan the wireless network. If any Access Point or IBSS is found, you could choose to connect it manually when client mode is enabled.

WPS Settings

Wi-Fi Protected Setup (WPS) is the simplest way to build connection between wireless network clients and this wireless router. You don’t have to select encryption mode and input a long encryption pass phrase every time when you need to setup a wireless client, you only have to press a button on wireless client and router, and the WPS will do the rest for you.

This wireless router supports two types of WPS: Push-Button Configuration (PBC), and PIN code. If you want to use PBC, you have to push a specific button on the wireless client to start WPS mode, and switch this wireless router to WPS mode too. You can push RET/WPS button of this wireless router, or click ‘Start PBC’ button in the web configuration interface to do this. If you want to use PIN code, you can see the setup as below.

Disable WPS

Check this box to disable WPS function, uncheck it to enable WPS.

WPS Status

Self-PIN Number

Push Button

Configuration

Client PIN Number

If the wireless security (encryption) function of this wireless router is properly set, you’ll see ‘Configured’ message here. If wireless security function has not been set, you’ll see ‘unConfigured’.

This is the WPS PIN code of this wireless router. This code is useful when router sets as Enrollee, you need to fill this number into the web page of the other device.

Click ‘Start PBC’ to start Push-Button style WPS setup procedure.

This wireless router will wait for WPS requests from wireless clients for 2 minutes. The ‘WLAN’ LED on the wireless router will be steady on when this wireless router is waiting for incoming WPS request.

Please input the PIN code of the other device you wish to connect, and click ‘Start PIN’ button. The ‘WLAN’ led on the wireless router will be steady on when this wireless router is waiting for incoming WPS request. (Please see the detail as below.)

- PBC setup step:

1. Ensure you have set the security setting on Router (as Registrar).

2. Click the WPS button on Router (or the “Start PBC” button on the web interface of Router) and the other device (supports PBC function) in 2 minutes.

3. Router (Registrar) would send SSID and security key to the other device (Enrollee) through tunnel to connect.

4. If you see the wireless client in the list, WPS-PBC setting is successful.

- PIN (as register) setup step:

1. Select Config Mode: “Registrar” on Router.

2. Fill the PIN code of the other device (as Enrollee that support WPS-PIN setting) into the “configure via Client Pincode” of Router.

3. Click the PIN buttons on Router and the other device in 2 minutes.

4. If you see the wireless client in the list, WPS-PIN setting is successful.

- PIN (as Enrollee) setup step:

1. Select Config Mode: “Enrollee” on Router.

2. Fill the PIN code of Router into the other device (as Registrar).

3. Click the PIN buttons on Router and the other device in 2 minutes.

4. If you see the wireless client in the list, WPS-PIN setting is successful.

** As the figure as above, just change two roles.

Wireless Schedule

This page allows you setup the wireless schedule rule. Please do not forget to configure system time before enable this feature.

Chapter 5

5

Firewall Settings

Port Filtering

Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway. Use of such filters can be helpful in securing or restricting your local network.

IP Filtering

Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway. Use of such filters can be helpful in securing or restricting your local network.

MAC Filtering

You can filter Internet access for local clients based on MAC Address. The MAC address filter enables you to allow or restrict specified nodes from communicating with other nodes.

Port Forwarding

The Port Forwarding allows you to re-direct a particular range of service port numbers (from the

Internet/WAN Ports) to a particular LAN IP address. It helps you to host some servers behind the firewall.

URL Filtering

URL filter is used to deny LAN port users from accessing the internet. Block those URLs which contain keywords listed below.

DMZ

A Demilitarized Zone is used to provide Internet services without sacrificing unauthorized access to its local private network. Typically, the DMZ host contains devices accessible to Internet traffic, such as

Web (HTTP) servers, FTP servers, SMTP (e-mail) servers and DNS servers.

QoS

Entries in this table improve your online gaming experience by ensuring that your game traffic is prioritized over other network traffic, such as FTP or Web.

Chapter 6

6

SIP Settings

Phone 1 / Phone 2

This page is used to configure the parameters for SIP registration information. Here you also could setup the other functions like Call Forward, Voice Codec, Speed Dial and others.

After finish all the settings, press the button to cancel the changes.

- Default Proxy

button to activate the new settings, or press the

Select Default Proxy

- Realm 1 / Realm 2

Each Phone port has support register two different Proxy

Servers. When select one of Proxy as default, Router will use this account for making outgoing call. And Router could receive incoming calls through both Proxys.

Default :

Realm1

Display Name

Line Number

Register Name

Register Password

Proxy

Proxy Server

Proxy Port

Domain Server

SIP Expire Time

Outbound Proxy

Outbound Proxy Server

Outbound Proxy Port

Nortel SoftSwitch

Register Status

Set Router Phone display name for caller ID information.

Default :

Null

Set registering Phone number.

Default :

Null

If Proxy server needs registration authentication please input

Login ID here.

Default :

Null

If Proxy server needs registration authentication please input password here.

Default :

Null

Check to enable Proxy mode.

Default :

Disable

If user enable Proxy mode, please input Proxy address.

Default :

Null

If user enable Proxy mode, please input Proxy port.

Default :

5060

Set SIP domain name for SIP signaling.

Default :

Null

Set expire time of registration. Router will keep re-registering to proxy server before expire timed out.

Default :

60 (sec)

Check to enable Outbound Proxy mode.

Default :

Disable

If user enables Outbound Proxy, please input Outbound Proxy address.

Default :

Null

If user enables Outbound Proxy, please input Outbound Proxy port.

Default :

5060

Enable this option for better compatibility capability with the

Nortel softswitch.

Default :

Disable

Here will display SIP account register status.

- Call Forward

All Forward

All Fwd No.

Busy Forward

Busy Number

No Answer Forward to

No Answer Number

No Answer Time (sec)

This is unconditional forward setting. All incoming call will be forwarded to specified number. Check to enable immediate forward function.

Default :

Off

Enter the assigned number for Immediate forward.

Default :

Null

Check to enable Busy Forward function. When phone is busy, incoming call will be forwarded to assigned number.

Default :

Off

Enter the assigned number for busy forward.

Default :

Null

Check to enable no answer forward function. When phone is not answered for a period of time, incoming call will be forwarded to assigned number.

Default :

Off

Enter assigned number for no answer forward.

Default :

Null

Set no answer time. Once phone is not picked up after this time, incoming call be will forwarded to assigned number.

Default :

0

- Abbreviated Dial (Phonebook)

Abbreviated Name

Abbreviated Dial (Phonebook) access code. Input this number and followed by # can dial out assigned phone number.

Set phone number for Router to make speed dial.

Phone Number

- Dial Plan

Replace prefix code

Select to enable (On) or disable (Off) prefix replace function.

Relace rule

Default :

Off

Set prefix replace rule. Once user dial number matched prefix,

Router will replace the number with assigned number. Available parameters are “0~9”, “#”, “*”, “+”, “x”. Symbol “+” means “or” , “x” could be numbers 0~9. For example, if user set Replace rule as

002+009->005

, which means if user dial 002 87654321 or 009

87654321, these number will be dial out as 005 87654321.

Dial Plan

Default :

Null

User can set how many digits or which number for Router to dial out immediately. Available parameters are “0~9”, “#”, “*”, “+”, “x”.

Symbol “+” means “or” , “x” could be numbers “0~9”. For example, user can set Dial Plan as “911+xxxxxxxx+*xx, which means if user dial 911, 87654321, or *11, these number will be dial out immediately without waiting for dial time or pressing # sign.

Default :

Null

-

Auto Prefix

Prefix Unset Plan

If user set Auto Prefix number, all number dialed out will be added with this prefix number. Available parameters are “0~9”, “#”, “*”.For example, user set Auto Prefix as 02, number 87654321 will be dial out as 02 87654321.

Default :

Null

User can set special access code to disable Auto Prefix function in single call. Available parameters are “0~9”, “#”, “*”, “+”, “x”. Symbol

+” means “or” , “x” could be numbers “0~9”. For example, if user set

Prefix Unset Plan as *1+xxxxxxxxxx. When dialed number as *1

87654321 or 10 digits of number, for this call will not be added with

Auto Prefix number.

Default :

Null

- Speed Dial

Position

Name

Phone Number

Select

Speed Dial access code. Press this speed dial number and followed by # can dial out assigned phone number.

Name of this speed dial.

Set phone number for Router to make speed dial.

User can delete selected speed dial data.

- SIP Advanced

SIP Port

Media Port

DMTF Relay

RFC2833 Payload Type

SIP INFO Duration (ms)

Call Waiting

Call Waiting Caller ID

Reject Direct IP Call

Set local SIP listening port.

Default :

5060

Set RTP port for sending voice data.

Default :

9000

Select DTMF Relay to be In band, RFC 2833, or SIP INFO.

Default :

Inband

If user select DTMF as RFC 2833 type, here can modify RFC

2833 payload type.

Default :

96

If user select DTMF as SIP INFO type, here can modify SIP

INFO duration. Router will send out DTMF as this duration.

Default :

250

Check to enable Call Waiting function.

Default :

Enable

Check to enable call waiting caller ID function. If this function is enabled, caller ID will display when having waiting call. Please note that your phone set should also support such function.

Default :

Disable

Check to enable Reject Direct IP Call. If this function is enabled,

Router will to reject the incoming peer to peer call.

Default :

Disable

- NAT Traversal

Stun

Stun Server Addr

Stun Server Port

- Codec

Precedence

Rate

Check to enable STUN function.

Default :

Disable

If user enables STUN function, please input STUN Server address.

Default :

Null

If user enables STUN function, please input STUN Server port.

Default :

3478

Set codec priority sequence.

Set G.723.1 codec with 5.3 or 6.3k mode.

- T.38 (FAX)

T.38

T.38 Port

Check to enable T.38 function.

Default :

Disable

Set T.38 port for FAX.

Default :

9008

- DSP – Digital Singnal Process Options

Vad

Caller ID Mode

Check to enable VAD (Voice Activity Detection) function.

Default :

Disable

Select caller ID mode as FSK (Bellcore), FSK (ETSI), FSK (BT),

FSK (NTT), or DTMF from Phone to send out.

Default :

DTMF

FSK Date & Time Sync

Check to send FSK Date and Time to caller ID display device.

Default :

Disable

Reverse Polarity before Caller

Check to send reverse polarity before caller ID.

ID

Default :

Disable

Short Ring before Caller ID

Dual Tone before Caller ID

Caller ID Prior First Ring

Caller ID DTMF Start Digit

Check to send short ring before caller ID.

Default :

Disable

Check to send dual tone before caller ID.

Default :

Disable

Check to send caller ID before first ring.

Default :

Enable

Set caller ID DTMF start digit.

Caller ID DTMF End Digit

Default :

DTMF_A

Set caller ID DTMF end digit.

Default :

DTMF_C

[ Space:10, Min:30, Max:2000 ]

Default :

200 ~ 500

[ -32~31 ], Mute:-32

Default :

0

Mic Voice Gain (dB) [ -32~31 ],

Set microphone voice gain volume.

Mute:-32

Default :

0

- Hot Line

Time

Use Hot Line

Hot Line Number

- DND (Don’t Disturb)

Hot Line Number

Default :

Disable

Set the destination number for Hot Line function.

Default :

Null

DND Mode

From

To

- Alarm

You can select 3 mode of DND. The call will be always rejected if

Always is selected. The call will be rejected by below Time setting (From and To) if Enable is selected. The call will be accepted if Disable is selected.

Default :

Disable

Set the start time for DND with Enable mode.

Default :

00:00

Set the end time for DND with Enable mode.

Default :

00:00

Enable

If set up as Enable, the telephone will ringed up at the specific time.

Default :

Disable

It can set up the system prompt time with 24 hours.

Default :

0:0

Tone

This page is used to configure the Tone

Parameters

country, or setup the custom tone parameters.

- Select Country

Country

User can select country to specify tone parameters (Dial Tone,

Ring Tone, Busy Tone, and Waiting Tone). If user wants to set tone manually, please select CUSTOMER. After selecting

CUSTOMER, user can assign Custom 1 to 8 for each tone.

Default :

TAIWAN

Select Coun try

Custom Tone

Select Custom tone number to set Tone Parameters.

Default :

Custom1

- Tone Parameters

Freq1

Freq2

Gain1

Gain2

CanOn

Set first set of tone frequency in Hz.

Default :

0

Set second set of tone frequency in Hz. This frequency is optional.

Default :

0

Set volume level of Freq1 in dB (-7~-10). Please set this parameter under zero and suggested to set between –7 to –10.

Default :

0

Set volume level of Freq2 in dB (-7~-10). Please set this parameter under zero and suggested to set between –7 to –10.

Default :

0

Set cadence time for tone to play in ms. For example, if set

CanOn as 100, the tone will be played for 100ms.

Default :

0

CanOff

Set cadence time for tone not to play in ms. For example, if set

CanOff as 100, the tone will stop playing for 100ms.

Default :

0

Other

This page is used to configure the function key and other parameters.

- Function Key

Call Transfer

Dial Option

Set call transfer function key.

Default :

*1

Auto Dial Time

Dial-out by Hash Key

Set Auto dial time. When user finish input number after this time,

Router will dial out immediately.

If the call is ended by “#”, the call will be send immediately and you do not need to wait for the Auto Dial time.

Default :

5

If the “#” symbol is used for other service purpose, it could disable this option. So that the dialing number could include the “#” symbol and send to destination side.

Default :

Enable

Off-Hook Alarm

Off-Hook Alarm Time

Set off-hook alarm time. If phone set has been off-hook, after this time, from phone sett will hear alarm.

Default :

30

- FXS Pulse Dial Detection

If your telephone set is pulse type, you can enable this option and define the interdigit pause duration parameters for operation priority.

SIP QoS

This page is used to configure the parameters for SIP QoS. You can define the DSCP code here for

SIP and RTP. Higher DSCP, higher priority. When DSCP is defined, a DSCP will be added in SIP and

RTP packets, and the priority of voice should be higher than data.

Chapter 7

Management

7

Status

In this page can show the current status and some basic settings of the Router.

Statistics

This page shows the packet counters for transmission and reception regarding to Ethernet networks.

DDNS

Dynamic DNS is a service, which provides you with a valid, unchanging, internet domain name (an URL) to go with that (possibly ever-changing) IP-address. Before setting this page, you should click below link to DynDNS or TZO to apply an account for DDNS.

Enable DDNS

Service Provider

Domain Name

User Name/Email

Password/Key

Check to enable DDNS function. User may register to DDNS server for DDNS function.

Select which server provider to implement DDNS function. For now we provide two servers: DynDNS and TZO.

Input the applied domain name for Router.

Input user name for DDNS server login.

Input password for DDNS server login.

Time Zone Setting

You can maintain the system time by synchronizing with a public time server over the Internet.

Current Time

Time Zone Select

Input current time manually.

Select local time zone according to location.

update

Router will automatically update current time from NTP server.

NTP server

User may select prefer NTP sever or input address of NTP server manually.

Denial-of-Service

A "denial-of-service" (DoS) attack is characterized by an explicit attempt by hackers to prevent legitimate users of a service from using that service.

Enable DoS Prevention

Check to enable DoS function.

User may set other related configurations about DoS below.

SNMP Management

This page is used to configure the parameters for SNMP. SNMP is a widely used protocol for monitoring the health and welfare of network equipment (eg. routers), computer equipment and even devices like UPSs.

Log

This page can be used to set remote log server and show the system log.

Enable Log

Check to enable log function.

System all/Dos

Select which log you want to check. Related information will be shown at below.

Upgrade Firmware

This page allows you upgrade the Router firmware to new version. Please note, do not power off the device during the upload because it may crash the system.

Select File

Browse and select file you want to upgrade and press Upload to perform upgrade.

Please wait till on screen shows related information after upgrade finished.

Auto Config

This page is used to configure Auto Config and Auto Update.

- Auto Config

Router supports HTTP, TFTP and FTP auto configuration function in total.

- Auto Firmware Update

The Router can update new firmware file automatically by the Auto Firmware Update function.

Mode

There are TFTP / FTP and HTTP three ways to provide the auto upgrade function.

TFTP Server Address

Input the TFTP Server address, and it could input the IP or

Domain Name form.

HTTP Server Address Input the HTTP Server address, and it could input the IP or

Domain Name form.

HTTP File Path

Set up the file path.

FTP Server Address

Input the FTP Server address, and it could input the IP or

Domain Name form.

FTP Username

The login username.

FTP Password

FTP Path

The login password

Set up the file path.

Check new firmware

The Router will according to the below ways to check the new firmware.

- Power On

: The machine will check the new firmware when power on and following the scheduling date and time.

- Scheduling

: The machine will follow the scheduling date and time to check the new firmware.

Scheduling Day

The Router will check the new firmware every the interval time.

The range is 1~30 days.

Scheduling Time

Automatic Updat

File Prefix

e

The Router will check the new firmware between the time range by random.

There are Notify only and Automatic ways to update.

- Notify only

: If there are new firmware, the Router will send the “Be Be Be” sounds when pick up the handset to prompt there are new firmware.

- Automatic

: The Router will carry firmware update out automatically.

It will check the information of model name.

Next update time

It will show the next check date and time.

Firmware Version

The current firmware version, the Router is use this value to decide if there is newer firmware version fo upgrading.

Save / Reload Settings

This page allows you save current settings to a file or reload the settings from the file which was saved previously. Besides, you could reset the current configuration to factory default.

Save Settings to File

Save current settings to a file.

Load Settings from File

Browse a file and upload to reload settings.

Reset Settings to Default

Press Reset will clean all current configurations and return to default values.

Password Setup

This page is used to set the account to access the web server of Router. Empty user name and password will disable the protection.

User Name

Enter user name.

New Password

Input password for this user.

Confirmed Password

Confirm password again.

Chapter 8

8

Fiber Setting

Fiber Setting

This function allows displaying the Fiber port’s status, Mode, Flow Control and Rate limit. The Link

Status in the screen displays the current connection speed and duplex mode.

Flow Control

Allow Enable or Disable flow control for selected port.

• Enable – 802.3x flow control is enabled on Full-Duplex mode or

Backpressure is enabled on Half-Duplex mode

• Disable – No flow control or backpressure function on no matter Full-Duplex or Half-Duplex mode

Default value: Disable

Ingress Rate Limit

Egress Shaping

The value of inbound traffic limitation in kilobit-per-second (kbps).

The possible values are :

• No Limit

• 512K

• 1M

• 2M

• 4M

• 8M

• 10M

• 50M

Default value: No Limit

The value of outbound traffic limitation in kilobit-per-second (kbps).

The possible values are :

• No Limit

• 512K

• 1M

• 2M

• 4M

• 8M

• 10M

• 50M

Default value : No Limit

61

Chapter 9

Utility

9

Ping Watchdog Setup

This page is used to configure the parameters for Ping Watchdog which pings to IP address every time interval. System will reboot when failing to ping the IP address 3 times.

Ping Test

This page is used to configure the parameters for Ping Test which pings to IP address or Domain

Name.

Traceroute

This page is used to configure the parameters for Traceroute which traces to IP address or Domain

Name.

Reboot

Press Reboot to reboot system. Please wait for a few minutes and reload web page again.

Logout

This page is used to logout.

Appendix A Voice communication samples

There are several ways to make calls to desired destination in Router. In this section, we’ll lead you step by step to establish your first voice communication via keypad and web browsers operations.

Peer to peer (P2P) mode

Assuming there are two routers in the network, the WAN port IP address are 192.168.0.1 and 192.168.0.2

Test the scenario:

1. To Phone A: Other Phone dials “192*168*0*1#”.

2. To Phone B: Other Phone dials “192*168*0*1**5062#”.

3. To Phone C: Other Phone dials “192*168*0*2#”.

4. To Phone D: Other Phone dials “192*168*0*2**5062#”.

L

Hint

y

If the IP address of the remote calling party is known, you may directly make calls by preset number via its IP address and end with “#”. y

If the VoIP Router is installed behind a NAT/firewall/

IP sharing device, please make sure the NAT device support SIP applications before making calls. y

The voice communication need to go through via WAN port of router, so it needs to make sure the WAN port connector is properly for communication.

Case 2: (Peer-to-Peer mode) FRT-420SN Port 1 to Port 2 communications

Supposing one FRT-420SN connects to two telephones, just pick up phone 1 and dial

192*168*0*1**5062’, phone 2 will ring.

Analog telephone sets are connected to the phone (RJ-11) ports of FRT-420SN respectively

Test the scenario:

1. Pick up the telephone set on Phone 1, and you should be able to hear the dial-tone

2. Press the keypad: 192*168*0*1**5062# shall be able to connect to the Phone 2

3. Then the telephone set in Phone 2 should ring.

4. The Phone 2 also could dial “192*168*0*1#” (without **5062) to Phone 1 to establish the voice communication.

L

Hint

y

If the IP address of the remote calling party is known, you may directly make calls via its IP address and end with“#”. y

If the router are installed behind a NAT/firewall/IP sharing device for Peer-to-Peer VoIP application, please make sure the NAT device support SIP applications, and suitable settings should be applied to the NAT device to enable the SIP communications before making calls y

[FRT-420SN] in PLANET Router series products, to connect to remote Router, press the keypad in the following sequence to connect to the remote FRT-420SN port 2:

[Remote Router IP address]**5062

, for example:

192*168*0*2**5062

Case 3: SIP Proxy mode

In this example, there are two Routers register to UMG-2000 via wireless connection. The telephone set could dial the extension number to each other.

STEP 1:

Log in UMG-2000 and create four testing accounts: 5001 ~ 5004 (password same as number) for

Router-A and Router-B. To enable the Wireless AP Service on UMG-2000 for wireless connection between Router-A and Router-B.

STEP 2:

Please log in Router-A via web browser, access to “Wireless Basic Settings” page to switch to

Client

mode, and fill in the SSID of UMG-2000 (UMG_WIFI). In the setting page, please insert the account/password information obtained from your service provider (in this sample, we’re using

PLANET UMG-2000 as the IP PBX server for SIP account, call authentications), and then the sample configuration screen is shown below:

It also could access to “Wireless Site Survey” menu to survey the wireless access connection and connect to UMG-2000.

STEP 3:

To assign the LAN port network parameters as 172.16.0.1 (IP Address) / 255.255.0.0 (Subnet

Mask).

STEP 4:

Please log in Router-A via web browser, find to the SIP item. In the setting page, please insert the account/password information obtained from your service provider (in this sample, we’re using

PLANET UMG-2000 as the IP PBX server for SIP account, call authentications), and then the sample configuration screen is shown below:

STEP 5:

Repeat the same configuration steps on Router-B, and check the machine registration status, make sure the registrations are completed.

STEP 6:

To verify the VoIP communication, please pick up the telephone. Dial the destination number to make call between SIP clients. For example, FXS 1 of Router-A (with number 5001) with keypad number

5003

to the FXS 1 of Router-B, or reversely makes calls from SIP client (Router-B) to the number

5001

(FXS 1 of Router-A).

Case 4: Call Forward Feature

In the following samples, we’ll introduce the Call Forward Feature applications.

In this example, both Routers register to UMG-2000 and FXS 2 of Router_A had set Call Forward function to FXS1 of Router_B.

Machine configuration on the Router:

Please log in Router_A via web browser, browse to the Phone 2 menu and select the Call Forward config menu. In the setting page, please enable the All Forward function and fill in the number of FXS

1 of Router_B (5003) in All Fwd No. field, then the sample configuration screen is shown below:

Test the scenario:

1. FXS 1 of Router_A (ext.5001) pick up the telephone

2. Dial the number

5002

(FXS 2 of Router _A),

3. Because FXS 2 of Router _A had set up All Forward function to the number

5003

(FXS 1 of

Router _B)

4. The number (FXS 1 of Router_B) will ring up then it pick up the telephone and communication with the number 5001

Case 5: FRT-420SN register with IPX-1900 via WAN port

In this example, the FRT-420SN registered with IPX-1900 via WAN port, and has VoIP communications with VIP-360PT.

STEP 1:

Log in IPX-1900 and create three testing accounts: 101 ~ 103 (password same as number) for

FRT-420SN and VIP-360PT.

STEP 2:

Please log in FRT-420SN via web browser, access to “WAN Interface Setup” page to setup the

WAN port network parameters for connect with IPX-1900.

STEP 3:

Please access to the SIP item. In the setting page, please insert the account/password information obtained from your service provider (in this sample, we’re using PLANET IPX-1900 as the IP PBX server for SIP account, call authentications), and then the sample configuration screen is shown below:

STEP 5:

Please log in VIP-360PT and access to “VOIP” page. According to the SIP account information to fill in the correspondence fields for registering with IPX-1900.

STEP 6:

To verify the VoIP communication, please pick up the telephone. Dial the destination number to make call between SIP clients. For example, FXS 1 of FRT-420SN with keypad number

103

to the

VIP-360PT. Or reversely makes calls from VIP-360PT SIP client to the number

101

(FXS 1 of

FRT-420SN).

Case 6: FRT-420SN register with UMG-2000 via WAN port

In this example, the Router-A and Router-B (FRT-420SN) registered with UMG-2000 via WAN port, and has VoIP communications with VIP-360PT that registered with LAN port of UMG-2000.

STEP 1:

Log in UMG-2000 and create three testing accounts: 5001 ~ 5005 (password same as number) for

Router-A, Router-B and VIP-360PT.

STEP 2:

Please log in FRT-420SN via web browser, access to “WAN Interface Setup” page to setup the

WAN port network parameters for connect with UMG-2000.

STEP 3:

Please access to the SIP item. In the setting page, please insert the account/password information

obtained from your service provider (in this sample, we’re using PLANET UMG-2000 as the IP PBX server for SIP account, call authentications), and then the sample configuration screen is shown below:

STEP 5:

Please log in VIP-360PT and access to “VOIP” page. According to the SIP account information to fill in the correspondence fields for registering with UMG-2000.

STEP 6:

To verify the VoIP communication, please pick up the telephone. Dial the destination number to make call between SIP clients. For example, FXS 1 of Router-A with keypad number

5005

to the

VIP-360PT. Or reversely makes calls from VIP-360PT SIP client to the number

5001

(FXS 1 of

Router-A).

Appendix B The method of featured voice operation guide

In this section, we’ll introduce the features method of operation, and lead you step by step to establish these features.

Call Transfer

1. B call to A and they are in the process of conversation.

2. A carry the transfer function out (Press *1 button) to hold the conversation with B.

3. A will hear the dial tone then input the number of C (Follow by the “#” key).

4. C will ring up then A hang up the handset.

5. C picks up the handset and conversation with B.

1. B call to A and they are in the process of conversation.

2. A carry the transfer function out (Press *1 button) to hold the conversation with B.

3. A will hear the dial tone then input the number of C (Follow by the “#” key).

4. C will ring up.

5. C picks up the handset and conversation with A.

6. A hang up and C conversation with B.

3-Way Conference

1. A and B are in the process of conversation.

2. A want to invite C to join their conversation.

3. A press ”Flash” button on telephone to hold the conversation with B at first and hear the dial tone, then input the number of C (Follow by the “#” key).

4. C will ring up and pick up the handset to conversation with A.

5. A press ”Flash” button again, and they will entry the 3-Way conference mode.

Call Waiting

1. A and B are in the process of conversation.

2. C call to A and A will hear the prompt sounds.

3. A press ”Flash” button to hold the conversation with B, and switch to conversation with C.

Switch the Default Proxy

Router can register to two different SIP Proxies at the same time. It can receive any one of different SIP accounts incoming call, and it can switch to any one SIP accounts for making calls through

input the switch code.

Realm switch code:

#1500#

: Realm 1

#1501#

: Realm 2

For example: The default is Realm 1, input the

#1501#

from keypad and hang up the telephone set. It will switch to Realm 2 can make the SIP calls via Realm 2.

Auto Update firmware by manual (Keypad)

If pick up the handset of Router, it will hear the “DoDoDo” prompt. If want to carry out the upgrade action, please input”

#190#

” to unlock the device at first. Then input”

#160#

” to upgrade the new firmware.

Appendix C

Frequently Asked Questions List

If your SIP Router is not functioning properly, you can refer to this chapter first for sample troubleshooting before contacting your dealer. This can save your time and effort but if the symptoms persist, please consult your dealer.

Q1: I forget my Router login username and / or password

A1:

1.) Restore Router to its factory default settings by pressing the “Reset” button which is at the side panel of the device for 5 seconds or more.

Q2: Non of the LEDs are on when I turn on the SIP Router

A2:

1.) Check if power cord is connected properly.

2.) Check if there is proper AC power coming from the power outlet.

Q3: Why can’t I dial my friend’s SIP number?

A3:

1.) Check SIP Server Domain Name/IP address. Make sure you have the right Name or IP address.

2.) Check the web browser and access the configuration menu. Make sure that the SIP Server Domain

Name/IP Address is correct.

3.) Check the register status under SIP Account Settings in the configuration menu (from web browser). If your status is “Not Registered, it means you do not have a SIP account. Contact your

SIP service provider to get an account.

Q4: How to know the machine IP address?

A4:

1.) To pick up the telephone set, and key in #120#.

2.) Machine will prompt the current LAN port IP address.

Appendix D Router Specifications

Product 802.11n Wireless VoIP Fiber Router

Model FRT-420SN

Hardware

WLAN Standards IEEE 802.11 b/g/n

Wireless Frequency Range 2.4GHz ~ 2.4835 GHz

Wireless Mode AP, Client, WDS and AP+WDS mode

64/128 bit WEP data encryption, WPA, WPA-PSK, WPA2, WPA2-PSK,

Security

WPA/WPA2 mix mode, 802.1x encryption and WPS PBC

Operating Frequencies /

Channel

USA/Canada: 2.412 GHz – 2.426 GHz (11 channels)

Europe: 2.412 GHz – 2.472 GHz (13 channels)

Japan: 2.412 GHz – 2.477 GHz (14 channels)

Wireless Data Rate

IEEE 802.11b: CCK (11Mbps,5.5Mbps), DQPSK (2Mbps), DBPSK

(1Mbps)

IEEE 802.11g: OFDM (54Mbps, 48Mbps, 36Mbps, 24Mbps, 18Mbps,

12Mbps, 9Mbps, 6Mbps)

IEEE 802.11n: 14/29/43/58/87/116/130/144Mps in 20MHz,

30/60/90/120/180/240/270/300Mbps in 40MHz

Transmit Power 802.11b: 17dBm, 802.11g: 15dBm, 802.11n: 13dBm

Receiver Sensitivity

Antenna

WDS

WAN

802.11b: -86dBm @11M, 802.11g: -72dBm @54M

802.11n (20MHz): -68dBm, 802.11n (40MHz): -66dBm

2 x 5dBi Detachable Antenna

WDS repeater support

1 x 100Base-FX port

LAN 4 x 10/100 Base-TX RJ-45 port

FXS (for telephone set connection)

2 x RJ-11 connection

Protocols and Standard

Standard

SIP 2.0 (RFC3261), SDP (RFC 2327), Symmetric RTP, STUN (RFC

3489), , ENUM (RFC 2916), RTP Payload for DTMF Digits (RFC2833),

Outbound Proxy Support, UPnP (UPnPTM)

Voice codec

Fax support*

Voice Standard

Protocols

Internet features

G.711(A-law /μ-law), G.729 AB, G.723 (6.3 Kbps / 5.3Kbps), G.276

(16,24,32,40 Kbps), GSM and G.722

T.38 (G.711 Fax pass-through)

VAD (Voice Activity Detection)

CNG (Comfort Noise Generation)

G.168: LEC (Line Echo Canceller)

Dynamic Jitter Buffer

In-band and out-of-band DTMF Relay (RFC 2833)

Caller ID Detection/Generation: DTMF, BELLCORE, ETSI, BT, NTT

SIP 2.0 (RFC-3261), TCP/IP, UDP/RTP/RTCP, HTTP, ICMP, ARP,

DNS, DHCP, NTP/SNTP, PPP, PPPoE

NAT router, DHCP server, Static routing, Virtual server, Virtual DMZ,

Smart QoS, IP ToS (IP Precedance) / DiffServ

MAC / IP / Port Filtering

URL Filtering

Port Forwarding, DMZ

Password protection for system management

Network and Configuration

Access Mode

Configuration &

Management

Static IP, PPPoE, DHCP

Web-Based Graphical User Interface

Remote management over the IP Network

Web-Based firmware upgrade

Backup and Restore Configuration file

Dimension (W x D x H)

Operating Environment

Power Requirement

EMC/EMI

FIBER SPECIFICATIONS

Product

WAN

Ports

LAN

Optic

Interface

Connector

Mode

Distance

Fiber-optic cable

SNMP v1/v2, Auto-Provision, Keypad on telephone set

186 x 143 x 35 mm

0~50 Degree C, 5~90% humidity

12V DC

CE, FCC Part 15 Class B

Internet Fiber Router

1 x 100Base-FX port

4 x 10/100Base-TX port

SFP

Vary on module

Vary on module

9/125μm single-mode cable, provide long distance for

15/20/35/50km or longer (very on SFP module)

advertisement

Related manuals