XM-320 Position Module User Manual

XM-320 Position Module User Manual
XM-320 Position Module
User Guide
Firmware Revision 5
1440-TPS02-01RB
Important User Information
Solid state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the
Application, Installation and Maintenance of Solid State Controls (publication SGI-1.1 available from your local Rockwell Automation sales
office or online at http://literature.rockwellautomation.com) describes some important differences between solid state equipment and hardwired electromechanical devices. Because of this difference, and also because of the wide variety of uses for solid state equipment, all
persons responsible for applying this equipment must satisfy themselves that each intended application of this equipment is acceptable.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use or
application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements
associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for actual use based on the
examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software described in
this manual.
Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is prohibited.
Throughout this manual, when necessary, we use notes to make you aware of safety considerations.
WARNING
IMPORTANT
ATTENTION
Identifies information about practices or circumstances that can cause an explosion in a
hazardous environment, which may lead to personal injury or death, property damage, or
economic loss.
Identifies information that is critical for successful application and understanding of the product.
Identifies information about practices or circumstances that can lead to personal injury or death,
property damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and
recognize the consequence
SHOCK HAZARD
Labels may be on or inside the equipment, for example, a drive or motor, to alert people that
dangerous voltage may be present.
BURN HAZARD
Labels may be on or inside the equipment, for example, a drive or motor, to alert people that
surfaces may reach dangerous temperatures.
Allen-Bradley, Rockwell Automation, and XM are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Safety Approvals
The following information applies when operating
this equipment in hazardous locations.
Informations sur l’utilisation de cet équipement en
environnements dangereux.
Products marked "CL I, DIV 2, GP A, B, C, D" are suitable
for use in Class I Division 2 Groups A, B, C, D, Hazardous
Locations and nonhazardous locations only. Each product
is supplied with markings on the rating nameplate
indicating the hazardous location temperature code.
When combining products within a system, the most
adverse temperature code (lowest "T" number) may be
used to help determine the overall temperature code of
the system. Combinations of equipment in your system
arfe subject to investigation by the local Authority Having
Jurisdiction at the time of installation.
Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne
conviennent qu'à une utilisation en environnements de
Classe I Division 2 Groupes A, B, C, D dangereux et non
dangereux. Chaque produit est livré avec des marquages
sur sa plaque d'identification qui indiquent le code de
température pour les environnements dangereux. Lorsque
plusieurs produits sont combinés dans un système, le
code de température le plus défavorable (code de
température le plus faible) peut être utilisé pour
déterminer le code de température global du système. Les
combinaisons d'équipements dans le système sont
sujettes à inspection par les autorités locales qualifiées
au moment de l'installation.
WARNING
EXPLOSION HAZARD -
AVERTISSEMENT
•Do not disconnect equipment unless power
has been removed or the area is known to be
nonhazardous.
•Do not disconnect connections to this
equipment unless power has been removed
or the area is known to be nonhazardous.
Secure any external connections that mate to
this equipment by using screws, sliding
latches, threaded connectors, or other means
provided with this product.
•Substitution of components may impair
suitability for Class I, Division 2.
•If this product contains batteries, they must
only be changed in an area known to be
nonhazardous.
IMPORTANT
Model
RISQUE D’EXPLOSION –
•Couper le courant ou s'assurer que
l'environnement est classé non dangereux
avant de débrancher l'équipement.
•Couper le courant ou s'assurer que
l'environnement est classé non dangereux
avant de débrancher les connecteurs. Fixer
tous les connecteurs externes reliés à cet
équipement à l'aide de vis, loquets
coulissants, connecteurs filetés ou autres
moyens fournis avec ce produit.
•La substitution de composants peut rendre
cet équipement inadapté à une utilisation en
environnement de Classe I, Division 2.
•S'assurer que l'environnement est classé non
dangereux avant de changer les piles.
Wiring to or from this device, which enters or leaves the system enclosure, must
utilize wiring methods suitable for Class I, Division 2 Hazardous Locations, as
appropriate for the installation in accordance with the product drawings as
indicated in the following table.
Catalog Number
Haz Location Drawings*
w/o
Barriers
XM-120
1440-VST0201RA
XM-121
1440-VLF0201RA
XM-122
Model
Catalog Number
w/
Barriers
Haz Location Drawings*
w/o
Barriers
w/
Barriers
48238-HAZ
48239-HAZ
48295-HAZ
48299-HAZ
XM-320
1440-TPS0201RB
XM-360
1440-TPR0600RE
1440-VSE0201RA
XM-361
1440-TUN0600RE
XM-123
1440-VAD0201RA
XM-361
1440-TTC0600RE
XM-160
1440-VDRS0600RH
XM-440
1440-RMA0004RC
48240-HAZ
N/A
XM-161
1440-VDRS0606RH
XM-441
1440-REX0004RD
48241-HAZ
N/A
XM-162
1440-VDRP0600RH
XM-442
1440-REX0304RG
48642-HAZ
N/A
XM-220
1440-SPD0201RB
48178-HAZ
51263-HAZ
48640-HAZ
48179-HAZ
51264-HAZ
48641-HAZ
* Drawings are available on the included CD
Table of Contents
Chapter 1
Introduction
Introducing the XM-320 Position Module . . . . . . . . . . . . . . . . . . . . . . . 1
XM-320 Module Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Using this Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Organization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Chapter 2
Installing the XM-320 Position
Module
XM Installation Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Grounding Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Mounting the Terminal Base Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
DIN Rail Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Interconnecting Terminal Base Units . . . . . . . . . . . . . . . . . . . . . . . 17
Panel/Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Connecting Wiring for Your Module . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Terminal Block Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Connecting the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Connecting the Relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Connecting the Short Circuit Protected Output . . . . . . . . . . . . . . 26
Connecting the Remote Relay Reset Signal . . . . . . . . . . . . . . . . . . 27
Connecting the Setpoint Multiplication Switch . . . . . . . . . . . . . . . 29
Connecting the 4-20mA Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Connecting the Transducer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
PC Serial Port Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
DeviceNet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Mounting the Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Module Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Basic Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Powering Up the Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Manually Resetting Relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Chapter 3
Configuration Parameters
v
Channel Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Measurement Mode Parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Normal Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Head-To-Head Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Radial Cancel Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Alarm Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Relay Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
4-20mA Output Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Triggered Trend Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
I/O Data Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Publication GMSI10-UM005C-EN-P - May 2010
Table of Contents
vi
Data Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Channel Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Alarm and Relay Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Device Mode Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Appendix A
Specifications
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Appendix B
DeviceNet Information
Electronic Data Sheets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Changing Operation Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Transition to Program Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Transition to Run Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
XM Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Invalid Configuration Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
XM-320 I/O Message Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Poll Message Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
COS Message Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Bit-Strobe Message Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
ADR for XM Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Appendix C
DeviceNet Objects
Publication GMSI10-UM005C-EN-P - May 2010
Identity Object (Class ID 01H) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Class Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Instance Attributes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
DeviceNet Object (Class ID 03H) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Class Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Instance Attributes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Assembly Object (Class ID 04H) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Class Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Instances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Instance Attributes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Assembly Instance Attribute Data Format. . . . . . . . . . . . . . . . . . . 88
Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Connection Object (Class ID 05H). . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Class Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Instances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Instance Attributes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Table of Contents
vii
Discrete Input Point Object (Class ID 08H) . . . . . . . . . . . . . . . . . . . . 92
Class Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Instance Attributes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Analog Input Point Object (Class ID 0AH) . . . . . . . . . . . . . . . . . . . . . 93
Class Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Instances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Instance Attributes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Parameter Object (Class ID 0FH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Class Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Instances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Instance Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Acknowledge Handler Object (Class ID 2BH) . . . . . . . . . . . . . . . . . . 98
Class Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Instances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Instance Attributes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Alarm Object (Class ID 31DH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Class Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Instances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Instance Attributes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Device Mode Object (Class ID 320H) . . . . . . . . . . . . . . . . . . . . . . . . 101
Class Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Instance Attributes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Relay Object (Class ID 323H) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Class Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Instances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Instance Attributes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Transducer Object (Class ID 328H) . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Class Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Instances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Instance Attributes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
4-20mA Output Object (Class ID 32AH) . . . . . . . . . . . . . . . . . . . . . 106
Class Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Instances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Instance Attributes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Glossary
Index
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Publication GMSI10-UM005C-EN-P - May 2010
Table of Contents
viii
Publication GMSI10-UM005C-EN-P - May 2010
Chapter
1
Introduction
This chapter provides an overview of the XM-320 Position module. It also
discusses the components of the module.
For information about
Introducing the XM-320
Position Module
See page
Introducing the XM-320 Position Module
1
XM-320 Module Components
3
Using this Manual
4
The XM-320 Position module is a 2-channel general purpose monitor. It is a
member of the Allen-Bradley™ XM® Series, a family of DIN rail mounted
condition monitoring and protection modules that operate both in stand-alone
applications or integrate with Programmable Logic Controllers (PLCs) and
control system networks.
The XM-320 supports the following measurements:
• Axial Position (Thrust) - Axial position (thrust) is a measurement of
the relative position of the thrust collar to the thrust bearing. It is a
measurement that may be made in both the active and inactive thrust
directions. The primary purpose of this measurement is to monitor
thrust bearing wear and to insure against axial rubs. It is recommended
that at least two separate transducers monitor axial position so that the
redundancy will give added protection.
Most steam turbine rotors operate within the total clearance between
thrust shoes (float). Normally this clearance is anywhere from 0.010 to
0.024 inches. The axial measurements are obtained by mounting a
non-contact probe axially, looking at the thrust collar or shaft. The
sensor provides a continuous measurement of the rotor position with
respect to the thrust bearing. In most applications, the thrust detector is
located in close proximity to the thrust bearing, normally located in the
turbine front standard.
1
Publication GMSI10-UM005C-EN-P - May 2010
2
Introduction
• Cam (Valve) Position - Valve position is a measurement of the main
steam inlet valve stem position. The valve position measurement
provides the operator with the current load on the machine.
The amount of the steam valve opening, speed, governor, and relay
valve position indication assists the operator in controlling the unit
during startup and emergencies. When used in conjunction with data
from other related Turbine Supervisory Instrumentation (TSI)
indicators, load, or steam flow related machinery conditions can be
diagnosed.
• Shell (Case) Expansion - Shell (Case) expansion is a measurement of
the thermal growth of the case from its fixed point outward. Steam
temperature swings widely between startup, shutdown, and various
operating conditions. The high pressure turbine end must move axially
as expansion and contraction occurs. Continuous indication of shell
thermal growth enables the operator to accelerate or change turbine
load without excessive distortion of the machine shell.
• Differential Expansion - Differential expansion (DE) is a
measurement of the differences between the thermal growth of the
rotor compared to the case.
Differential expansion monitoring provides the machine operator with
continuous indication of the critical clearances between the expanding
rotor and blades with respect to the expanding shell or casing. Proper
coordination of machine parameters enables safe machine acceleration
and operation during load changes and emergencies. To prevent axial
rubs it is important that the rotor and case grow at the same rate.
Differential expansion is most important during a turbine “cold”
startup. The rotor is fixed axially by the thrust bearing. The thrust
bearing moves as the case expands – thus the need to monitor the
difference in thermal expansion. Ideally, differential expansion should
indicate zero change in the gap relationship between the two surfaces.
When the shell growth leads or lags the rotor growth, or conversely the
rotor expansion leads or lags the shell growth, an expansion differential
occurs.
The XM-320 accepts input from linear variable differential transformers
(LVDT), non-contact eddy current probes, rotary cam (valve) potentiometers,
or any voltage output position measurement device.
Publication GMSI10-UM005C-EN-P - May 2010
Introduction
3
The XM-320 also includes a single on-board relay, expandable to five, two
4-20mA outputs, and a buffered output for each input. The module can collect
trend data on event, and monitor up to two alarms making it a complete
position monitoring system. The module can operate stand-alone, or it can be
deployed on a standard or dedicated DeviceNet network where it can provide
real-time data and status information to other XM modules, PLCs, DCS, and
Condition Monitoring Systems.
The XM-320 module is configurable over a DeviceNet network or using a
serial connection to a PC or laptop. Refer to Chapter 3 for a list of the XM-320
configuration parameters.
XM-320 Module
Components
The XM-320 consists of a terminal base unit and an instrument module. The
XM-320 Position Module and the XM-941 Position Terminal Base are shown
below.
Figure 1.1 XM-320 Module Components
POSITION
XM-941 Position Module Terminal Base Unit
Cat. No. 1440-TB-B
1440-TPS02-01R
B
XM-320 Position Module
Cat. No. 1440-TPS02-01RB
• XM-941 Position Module Terminal Base Unit - A DIN rail mounted
base unit that provides terminations for all field wiring required by XM
Position modules, including the XM-320.
Publication GMSI10-UM005C-EN-P - May 2010
4
Introduction
• XM-320 Position Module - Mounts on the XM-941 terminal base unit
via a keyswitch and a 96-connector. The XM-320 contains the
measurement electronics, processor, relay, and serial interface port for
local configuration.
IMPORTANT
The XM-441 Expansion Relay module may be connected
to the XM-320 module via the XM-941 terminal base unit.
When connected to the XM-320, the Expansion Relay
module simply “expands” the capability of the XM-320 by
adding four additional epoxy-sealed relays. The XM-320
controls the Expansion Relay module by extending to it the
same logic and functional controls as the XM-320 module’s
on-board relay.
Using this Manual
This manual introduces you to the XM-320 Position module. It is intended for
anyone who installs, configures, or uses the XM-320 Position module.
Organization
To help you navigate through this manual, it is organized in chapters based on
these tasks and topics.
Chapter 1 “Introduction” contains an overview of this manual and the
XM-320 module.
Chapter 2 “Installing the XM-320 Position Module” describes how to install,
wire, and use the XM-320 module.
Chapter 3 “Configuration Parameters” provides a complete listing and
description of the XM-320 parameters. The parameters can be viewed and
edited using the XM Serial Configuration Utility software and a personal
computer.
Appendix A “Specifications” lists the technical specifications for the XM-320
module.
Appendix B “DeviceNet Information” provides information to help you
configure the XM-320 over a DeviceNet network.
Appendix C “DeviceNet Objects” provides information on the DeviceNet
objects supported by the XM-320 module.
For definitions of terms used in this Guide, see the Glossary at the end of the
Guide.
Publication GMSI10-UM005C-EN-P - May 2010
Introduction
5
Document Conventions
There are several document conventions used in this manual, including the
following:
The XM-320 Position Module is referred to as XM-320, Position module,
module, or device throughout this manual.
TIP
EXAMPLE
A tip indicates additional information which may be
helpful.
This convention presents an example.
Publication GMSI10-UM005C-EN-P - May 2010
6
Introduction
Publication GMSI10-UM005C-EN-P - May 2010
Chapter
2
Installing the XM-320 Position Module
This chapter discusses how to install and wire the XM-320 Position Module. It
also describes the module indicators and the basic operations of the module.
For information about
See page
XM Installation Requirements
8
Mounting the Terminal Base Unit
15
Connecting Wiring for Your Module
19
Mounting the Module
39
Module Indicators
41
Basic Operations
43
ATTENTION
Environment and Enclosure
This equipment is intended for use in a Pollution Degree 2
Industrial environment, in overvoltage Category II applications
(as defined in IED publication 60664–1), at altitudes up to 2000
meters without derating.
This equipment is supplied as “open type” equipment. It must be
mounted within an enclosure that is suitably designed for those
specific environmental conditions that will be present, and
appropriately designed to prevent personal injury resulting from
accessibility to live parts. The interior of the enclosure must be
accessible only by the use of a tool. Subsequent sections of this
publication may contain additional information regarding specific
enclosure type ratings that are required to comply with certain
product safety certifications.
See NEMA Standards publication 250 and IEC publication
60529, as applicable, for explanations of the degrees of
protection provided by different types of enclosures.
7
Publication GMSI10-UM005C-EN-P - May 2010
8
Installing the XM-320 Position Module
XM Installation
Requirements
This section describes wire, power and grounding requirements, and
instructions for an XM system.
Wiring Requirements
Use solid or stranded wire. All wiring should meet the following specifications:
• 14 to 22 AWG copper conductors without pretreatment; 8 AWG
required for grounding the DIN rail for electromagnetic interference
(emi) purposes
• Recommended strip length 8 millimeters (0.31 inches)
• Minimum insulation rating of 300V
• Soldering the conductor is forbidden
• Wire ferrules can be used with stranded conductors; copper ferrules
recommended
ATTENTION
See the XM Documentation and Configuration Utility CD
for Hazardous Locations installation drawings. The XM
Documentation and Configuration Utility CD is packaged
with the XM modules.
Power Requirements
Before installing your module, calculate the power requirements of all modules
interconnected via their side connectors. The total current draw through the
side connector cannot exceed 3A. Refer to the specifications for the specific
modules for power requirements.
ATTENTION
A separate power connection is necessary if the total
current draw of the interconnecting modules is greater than
3A.
Figure 2.1 is an illustration of wiring modules using separate power
connections.
Publication GMSI10-UM005C-EN-P - May 2010
Installing the XM-320 Position Module
9
Figure 2.1 XM Modules with Separate Power Connections
Any limited power
source that satisfies
the requirements
specified below
Power Supply Requirements
XM Power Supply Requirements
Listed Class 2 rated supply, or
Protection
Fused* ITE Listed SELV supply, or
Fused* ITE Listed PELV supply
Output Voltage
24 Vdc ± 10%
Output Power
100 Watts Maximum (~4A @ 24 Vdc)
Static Regulation
± 2%
Dynamic Regulation
± 3%
Ripple
< 100mVpp
Output Noise
Per EN50081-1
Overshoot
< 3% at turn-on, < 2% at turn-off
Hold-up Time
As required (typically 50mS at full rated load)
* When a fused supply is used the fuse must be a 5 amp, listed, fast acting fuse such as
provided by Allen-Bradley part number 1440-5AFUSEKIT
Publication GMSI10-UM005C-EN-P - May 2010
10
Installing the XM-320 Position Module
IMPORTANT
See Application Technique "XM Power Supply Solutions",
publication ICM-AP005A-EN-E, for guidance in
architecting power supplies for XM systems.
Grounding Requirements
Use these grounding requirements to ensure safe electrical operating
circumstances, and to help avoid potential emi and ground noise that can cause
unfavorable operating conditions for your XM system.
DIN Rail Grounding
The XM modules make a chassis ground connection through the DIN rail.
The DIN rail must be connected to a ground bus or grounding electrode
conductor using 8 AWG or 1 inch copper braid. See Figure 2.2.
Use zinc-plated, yellow-chromated steel DIN rail (Allen-Bradley part no.
199-DR1 or 199-DR4) or equivalent to assure proper grounding. Using other
DIN rail materials (e.g. aluminum, plastic, etc.), which can corrode, oxidize, or
are poor conductors can result in improper or intermittent platform
grounding.
Publication GMSI10-UM005C-EN-P - May 2010
Installing the XM-320 Position Module
11
Figure 2.2 XM System DIN Rail Grounding
1
1440-VST02-01RA
DYNAMIC MEASUREMENT
1440-REX00-04RD
EXPANSION RELAY
1440-VST02-01RA
DYNAMIC MEASUREMENT
1440-REX00-04RD
EXPANSION RELAY
Power
Supply
1440-RMA00-04RC
MASTER RELAY
1
1440-REX00-04RD
EXPANSION RELAY
1440-VST02-01RA
DYNAMIC MEASUREMENT
1440-TSP02-01RB
POSITION
1440-REX00-04RD
EXPANSION RELAY
1440-REX00-04RD
EXPANSION RELAY
1440-VST02-01RA
DYNAMIC MEASUREMENT
1440-REX00-04RD
EXPANSION RELAY
Power
Supply
1
Use 14 AWG wire.
The grounding wire can be connected to the DIN rail using a DIN Rail
Grounding Block (Figure 2.3).
Publication GMSI10-UM005C-EN-P - May 2010
12
Installing the XM-320 Position Module
Figure 2.3 DIN Rail Grounding Block
Panel/Wall Mount Grounding
The XM modules can also be mounted to a conductive mounting plate that is
grounded. See Figure 2.5. Use the grounding screw hole provided on the
terminal base to connect the mounting plate the Chassis terminals.
Figure 2.4 Grounding Screw on XM Terminal Base
Publication GMSI10-UM005C-EN-P - May 2010
Installing the XM-320 Position Module
13
Figure 2.5 Panel/Wall Mount Grounding
1
Power
Supply
1
Power
Supply
1
Use 14 AWG wire.
Publication GMSI10-UM005C-EN-P - May 2010
14
Installing the XM-320 Position Module
24V Common Grounding
24V power to the XM modules must be grounded. When two or more power
supplies power the XM system, ground the 24V Commons at a single point,
such as the ground bus bar.
IMPORTANT
IMPORTANT
If it is not possible or practical to ground the -24Vdc
supply, then it is possible for the system to be installed and
operate ungrounded. However, if installed ungrounded
then the system must not be connected to a ground
through any other circuit unless that circuit is isolated
externally. Connecting a floating system to a non-isolated
ground could result in damage to the XM module(s)
and/or any connected device. Also, operating the system
without a ground may result in the system not performing
to the published specifications regards measurement
accuracy and communications speed, distance or reliability.
The 24V Common and Signal Common terminals are
internally connected. They are isolated from the Chassis
terminals unless they are connected to ground as described
in this section. See Terminal Block Assignments on page 20
for more information.
Transducer Grounding
Make certain the transducers are electrically isolated from earth ground. Cable
shields must be grounded at one end of the cable, and the other end left
floating or not connected. It is recommended that where possible, the cable
shield be grounded at the XM terminal base (Chassis terminal) and not at the
transducer.
DeviceNet Grounding
The DeviceNet network is functionally isolated and must be referenced to
earth ground at a single point. XM modules do not require an external
DeviceNet power supply. Connect DeviceNet V- to earth ground at one of the
XM modules, as shown in Figure 2.6.
Publication GMSI10-UM005C-EN-P - May 2010
Installing the XM-320 Position Module
15
Figure 2.6 Grounded DeviceNet V- at XM Module
To
Ground
Bus
ATTENTION
Use of a separate DeviceNet power supply is not
permitted. See Application Technique "XM Power Supply
Solutions", publication ICM-AP005A-EN-E, for guidance
in using XM with other DeviceNet products.
For more information on the DeviceNet installation, refer to the ODVA
Planning and Installation Manual - DeviceNet Cable System, which is available
on the ODVA web site (http://www.odva.org).
Switch Input Grounding
The Switch Input circuits are functionally isolated from other circuits. It is
recommended that the Switch RTN signal be grounded at a single point.
Connect the Switch RTN signal to the XM terminal base (Chassis terminal) or
directly to the DIN rail, or ground the signal at the switch or other equipment
that is wired to the switch.
Mounting the Terminal
Base Unit
The XM family includes several different terminal base units to serve all of the
measurement modules. The XM-941 terminal base, Cat. No. 1440-TB-B, is the
only terminal base unit used with the XM-320.
Publication GMSI10-UM005C-EN-P - May 2010
16
Installing the XM-320 Position Module
The terminal base can be DIN rail or wall/panel mounted. Refer to the
specific method of mounting below.
ATTENTION
The XM modules make a chassis ground connection
through the DIN rail. Use zinc plated, yellow chromated
steel DIN rail to assure proper grounding. Using other
DIN rail materials (e.g. aluminum, plastic, etc.), which can
corrode, oxidize or are poor conductors can result in
improper or intermittent platform grounding.
You can also mount the terminal base to a grounded
mounting plate. Refer to Panel/Wall Mount Grounding on
page 12.
DIN Rail Mounting
Use the steps below to mount the XM-941 terminal base unit on a DIN rail
(A-B pt no. 199-DR1 or 199-DR4).
1. Position the terminal base on the 35 x 7.5mm DIN rail (A).
Position terminal base at a slight angle and hook over the top of the DIN rail.
2. Slide the terminal base unit over leaving room for the side
connector (B).
Publication GMSI10-UM005C-EN-P - May 2010
Installing the XM-320 Position Module
17
3. Rotate the terminal base onto the DIN rail with the top of the rail
hooked under the lip on the rear of the terminal base.
4. Press down on the terminal base unit to lock the terminal base on the
DIN rail. If the terminal base does not lock into place, use a screwdriver
or similar device to open the locking tab, press down on the terminal
base until flush with the DIN rail and release the locking tab to lock the
base in place.
Interconnecting Terminal Base Units
Follow the steps below to install another terminal base unit on the DIN rail.
IMPORTANT
Make certain you install the terminal base units in order of
left to right.
1. Position the terminal base on the 35 x 7.5mm DIN rail (A).
2. Make certain the side connector (B) is fully retracted into the base unit.
3. Slide the terminal base unit over tight against the neighboring terminal
base. Make sure the hook on the terminal base slides under the edge of
the terminal base unit.
4. Press down on the terminal base unit to lock the terminal base on the
DIN rail. If the terminal base does not lock into place, use a screwdriver
or similar device to open the locking tab, press down on the terminal
base until flush with the DIN rail and release the locking tab to lock the
base in place.
Publication GMSI10-UM005C-EN-P - May 2010
18
Installing the XM-320 Position Module
5. Gently push the side connector into the side of the neighboring terminal
base unit to complete the backplane connection.
Panel/Wall Mounting
Installation on a wall or panel consists of:
• laying out the drilling points on the wall or panel
• drilling the pilot holes for the mounting screws
• installing the terminal base units and securing them to the wall or panel
Use the following steps to install the terminal base on a wall or panel.
Publication GMSI10-UM005C-EN-P - May 2010
Installing the XM-320 Position Module
19
1. Lay out the required points on the wall/panel as shown in the drilling
dimension drawing below.
Side Connector
2. Drill the necessary holes for the #6 self-tapping mounting screws.
3. Secure the terminal base unit using two #6 self-tapping screws.
4. To install another terminal base unit, retract the side connector into the
base unit. Make sure it is fully retracted.
5. Position the terminal base unit up tight against the neighboring terminal
base. Make sure the hook on the terminal base slides under the edge of
the terminal base unit.
6. Gently push the side connector into the side of the neighboring terminal
base to complete the backplane connection.
7. Secure the terminal base to the wall with two #6 self-tapping screws.
Connecting Wiring for Your
Module
Wiring to the module is made through the terminal base unit on which the
module mounts. The XM-320 is compatible only with the XM-941 terminal
base unit, Cat. No. 1440-TB-B.
Publication GMSI10-UM005C-EN-P - May 2010
20
Installing the XM-320 Position Module
Figure 2.7 XM-941 Terminal Base Unit
XM-941, Cat. No. 1440-TB-B
Terminal Block Assignments
The terminal block assignments and descriptions for the XM-320 module are
shown below.
ATTENTION
WARNING
The terminal block assignments are different for different
XM modules. The following table applies only to the
XM-320. Refer to the installation instructions for the
specific XM module for its terminal assignments.
EXPLOSION HAZARD
Do not disconnect equipment unless power has been
removed or the area is known to be nonhazardous.
Do not disconnect connections to this equipment unless
power has been removed or the area is known to be
nonhazardous. Secure any external connections that mate
to this equipment by using screws, sliding latches, threaded
connectors, or other means provided with this product.
Terminal Block Assignments
Publication GMSI10-UM005C-EN-P - May 2010
No.
Name
Description
0
Xducer 1 (+)
Transducer 1 connection
1
Xducer 2 (+)
Transducer 2 connection
2
Protected Output 1
(+)
Short Circuit Protected Output 1, positive side
3
Protected Output 2
(+)
Short Circuit Protected Output 2, positive side
4
No Connection
5
No Connection
6
Xducer V (+)
Transducer power supply output, positive side
Installing the XM-320 Position Module
21
Terminal Block Assignments
No.
Name
Description
7
TxD
PC serial port, transmit data
8
RxD
PC serial port, receive data
9
XRTN
Circuit return for TxD and RxD
10
Chassis
Connection to DIN rail ground spring or panel mounting hole
11
4-20mA 1 (+)
12
4-20mA 1 (-)
4-20mA output
600 ohm maximum load
13
Chassis
Connection to DIN rail ground spring or panel mounting hole
14
Chassis
Connection to DIN rail ground spring or panel mounting hole
15
Chassis
Connection to DIN rail ground spring or panel mounting hole
16
Xducer 1 (-)
Transducer 1 connection
17
Xducer 2 (-)
Transducer 2 connection
18
Protected Output 1
(-)
Short Circuit Protected Output 1, negative side
19
Protected Output 2
(-)
Short Circuit Protected Output 2, negative side
20
No Connection
21
No Connection
22
Xducer V (-)
Transducer power supply output, negative side
23
CAN_High
DeviceNet bus connection, high differential (white wire)
24
CAN_Low
DeviceNet bus connection, low differential (blue wire)
25
+24V Out
Internally connected to 24V In (terminal 44)
Used to daisy chain power if XM modules are not plugged into
each other
26
DNet V (+)
DeviceNet bus power input, positive side (red wire)
27
DNet V (-)
DeviceNet bus power input, negative side (black wire)
28
24V Common
Internally connected to 24V Common (terminals 43 and 45)
Used to daisy chain power if XM modules are not plugged into
each other
29
4-20mA 2 (+)
30
4-20mA 2 (-)
4-20mA output
600 ohm maximum load
31
Chassis
Connection to DIN rail ground spring or panel mounting hole
32
Chassis
Connection to DIN rail ground spring or panel mounting hole
33
Chassis
Connection to DIN rail ground spring or panel mounting hole
34
Chassis
Connection to DIN rail ground spring or panel mounting hole
35
Chassis
Connection to DIN rail ground spring or panel mounting hole
36
Chassis
Connection to DIN rail ground spring or panel mounting hole
37
Chassis
Connection to DIN rail ground spring or panel mounting hole
38
Chassis
Connection to DIN rail ground spring or panel mounting hole
Publication GMSI10-UM005C-EN-P - May 2010
22
Installing the XM-320 Position Module
Terminal Block Assignments
No.
Name
Description
39
SetPtMult
Switch input to activate Set Point Multiplication (active closed)
40
Switch RTN
Switch return, shared between SetPtMult and Reset Relay
41
Reset Relay
Switch input to reset internal relay (active closed)
42
Reserved
43
24V Common
Internally DC-coupled to circuit ground
44
+24V In
Connection to primary external +24V power supply, positive
side
45
24V Common
Connection to external +24V power supply, negative side
(internally DC-coupled to circuit ground)
46
Relay N.C. 1
Relay Normally Closed contact 1
47
Relay Common 1
Relay Common contact 1
48
Relay N.O. 1
Relay Normally Open contact 1
49
Relay N.O. 2
Relay Normally Open contact 2
50
Relay Common 2
Relay Common contact 2
51
Relay N.C. 2
Relay Normally Closed contact 2
Connecting the Power Supply
Power supplied to the module must be nominally 24 Vdc (±10%) and must be
a Class 2 rated circuit.
Wire the DC-input power supply to the terminal base unit as shown in Figure
2.8.
Figure 2.8 DC Input Power Supply Connections
24V dc
Power
Supply
Publication GMSI10-UM005C-EN-P - May 2010
+
-
-
Installing the XM-320 Position Module
IMPORTANT
IMPORTANT
ATTENTION
23
A Class 2 circuit can be provided by use of an NEC Class 2
rated power supply, or by using a SELV or PELV rated
power supply with a 5 Amp current limiting fuse installed
before the XM module(s).
24Vdc needs to be wired to terminal 44 (+24 V In) to
provide power to the device and other XM modules linked
to the wired terminal base via the side connector.
The power connections are different for different XM
modules. Refer to the installation instructions for your
specific XM module for complete wiring information.
Connecting the Relays
The XM-320 has both Normally Open (NO) and Normally Closed (NC) relay
contacts. Normally Open relay contacts close when the control output is
energized. Normally Closed relay contacts open when the control output is
energized.
The alarms associated with the relay and whether the relay is normally
de-energized (non-failsafe) or normally energized (failsafe) depends on the
configuration of the module. Refer to Relay Parameters on page 58 for details.
Table 2.1 shows the on-board relay connections for the XM-320.
IMPORTANT
TIP
All XM relays are double pole. This means that each relay
has two contacts in which each contact operates
independently but identically. The following information
and illustrations show wiring solutions for both contacts;
although, in many applications it may be necessary to wire
only one contact.
The Expansion Relay module may be connected to the
XM-320 to provide additional relays. Refer to the XM-441
Expansion Relay Module User Guide for wiring details.
Publication GMSI10-UM005C-EN-P - May 2010
24
Installing the XM-320 Position Module
IMPORTANT
T
The NC/NO terminal descriptions (page 22) correspond
to a de-energized (unpowered) relay.
When the relay is configured for non-failsafe operation, the
relay is normally de-energized.
When the relay is configured for failsafe operation, the
relay is normally energized, and the behavior of the NC and
NO terminals is inverted.
Table 2.1 Relay Connections for XM-320
Configured for
Failsafe Operation
Relay 1 Terminals
Nonalarm
Alarm
Wire Contacts
Contact 1
Contact 2
Closed
Opened
COM
47
50
NO
48
49
COM
47
50
NC
46
51
Opened
Closed
Configured for
Non-failsafe Operation
Relay 1 Terminals
Nonalarm
Alarm
Wire Contacts
Contact 1
Contact 2
Closed
Opened
COM
47
50
NC
46
51
COM
47
50
NO
48
49
Opened
Closed
Figures 2.9 and 2.10 illustrate the behavior of the NC and NO terminals when
the relay is wired for failsafe, alarm or nonalarm condition or non-failsafe,
alarm or nonalarm condition.
Publication GMSI10-UM005C-EN-P - May 2010
Installing the XM-320 Position Module
25
Figure 2.9 Relay Connection - Failsafe, Nonalarm Condition
Non-failsafe, Alarm Condition
Figure 2.10 Relay Connection - Failsafe, Alarm Condition
Non-failsafe, Nonalarm Condition
Alternate Relay Wiring
Figures 2.11 and 2.12 show how to wire both ends of a single external
indicator to the XM terminal base for failsafe, nonalarm or alarm condition, or
non-failsafe, nonalarm or alarm condition.
Publication GMSI10-UM005C-EN-P - May 2010
26
Installing the XM-320 Position Module
Figure 2.11 Relay Connection - Failsafe, Nonalarm Condition
Non-failsafe, Alarm Condition
Figure 2.12 Relay Connection - Failsafe, Alarm Condition
Non-failsafe, Nonalarm Condition
Connecting the Short Circuit Protected Output
The XM-320 provides short circuit protected outputs of all transducer input
signals. The protected output connections may be used to connect the module
to portable data collectors or other online systems.
Figure 2.13 shows the short circuit protected output connections for the
XM-320.
Publication GMSI10-UM005C-EN-P - May 2010
Installing the XM-320 Position Module
27
Figure 2.13 Short Circuit Protected Output Connections
Connecting the Remote Relay Reset Signal
If you set the module relay to latching and the relay activates, the relay stays
activated even when the condition that caused the alarm has ended. The
remote relay reset signal enables you to reset your module relay remotely after
you have corrected the alarm condition. This includes latched relays in the
Expansion Relay module when it is attached to the XM-320.
TIP
TIP
You can discretely reset a relay using the serial or remote
configuration tool.
If you set a module relay to latching, make sure that any
linked relays, such as relays in an XM-440 Master Relay
Module, are not configured as latching. When both relays
are set to latching, the relay in each module will have to be
independently reset when necessary.
Wire the Remote Relay Reset Signal to the terminal base unit as shown in
Figure 2.14.
Publication GMSI10-UM005C-EN-P - May 2010
28
Installing the XM-320 Position Module
Figure 2.14 Remote Relay Reset Signal Connection
ATTENTION
The Switch Input circuits are functionally isolated from
other circuits. It is recommended that the Switch RTN
signal be grounded at a signal point. Connect the Switch
RTN signal to the XM terminal base (Chassis terminal) or
directly to the DIN rail, or ground the signal at the switch
or other equipment that is wired to the switch.
A single switch contact can also be shared by multiple XM modules wired in
parallel as shown in Figure 2.15.
ATTENTION
The relay reset connections may be different for different
XM modules. Figure 2.15 applies only to the XM-320
module. Refer to the installation instructions for the
module for its terminal assignments.
Figure 2.15 Typical Multiple XM Modules Remote Relay Reset Signal Connection
Publication GMSI10-UM005C-EN-P - May 2010
Installing the XM-320 Position Module
29
Connecting the Setpoint Multiplication Switch
You can configure the module to multiply the alarm setpoints, or inhibit the
alarms during the start-up period. This can be used to avoid alarm conditions
that may occur during startup, for example, when the monitored machine
passes through a critical speed.
Wire the Setpoint Multiplication switch to the terminal base unit as shown in
Figure 2.16.
Figure 2.16 Setpoint Multiplication Connection
ATTENTION
The Switch Input circuits are functionally isolated from
other circuits. It is recommended that the Switch RTN
signal be grounded at a signal point. Connect the Switch
RTN signal to the XM terminal base (Chassis terminal) or
directly to the DIN rail, or ground the signal at the switch
or other equipment that is wired to the switch.
Connecting the 4-20mA Outputs
The module includes an isolated 4-20mA per channel output into a maximum
load of 600 ohms. The measurements that the 4-20mA output tracks and the
signal levels that correspond to the 4mA and 20mA are configurable. Refer
to 4-20mA Output Parameters on page 62 for a description of the 4-20mA
parameters.
Wire the 4-20mA outputs to the terminal base unit as shown in Figure 2.17.
Publication GMSI10-UM005C-EN-P - May 2010
30
Installing the XM-320 Position Module
Figure 2.17 4-20mA Output Connections
ATTENTION
The 4-20mA outputs are functionally isolated from other
circuits. It is recommended that the outputs be grounded at
a single point. Connect the 4-20mA (-) to the XM terminal
base (Chassis terminal) or directly to the DIN rail, or
ground the signal at the other equipment in the 4-20mA
loop.
Connecting the Transducer
The XM-320 will accept signals from a linear variable differential transformer
(LVDT), non-contact eddy current probe, or a rotary cam (valve)
potentiometer.
Connecting a Non-contact Sensor
The following figures show the wiring from a non-contact sensor to the
terminal base unit of the XM-320 module.
ATTENTION
Publication GMSI10-UM005C-EN-P - May 2010
You may ground the cable shield at either end of the cable.
Do not ground the shield at both ends. Recommended
practice is to ground the cable shield at the XM-320
terminal base and not at the transducer. Any convenient
Chassis terminal may be used (see Terminal Block
Assignments on page 20).
Installing the XM-320 Position Module
31
Figure 2.18 Non-contact sensor to channel 1 wiring
TYPICAL WIRING FOR NON-CONTACT SENSOR
TO XM-320 POSITION MODULE CHANNEL 1
Isolated Sensor Driver
Shield
Floating
-24
SIG
COM
Signal Common
Channel 1 Input Signal
16
0
Shield
37
-24V DC
22
6
43
Figure 2.19 Non-contact sensor to channel 2 wiring
TYPICAL WIRING FOR NON-CONTACT SENSOR
TO XM-320 POSITION MODULE CHANNEL 2
Isolated Sensor Driver
Shield
Floating
-24
SIG
COM
Signal Common
Channel 2 Input Signal
Shield
-24V DC
17
1
* See note
38
22
6
43
Note: If connecting non-contact sensors to both channels 1 and 2, install jumper between
terminals 17 and 43 instead of terminals 17 and 6 in order to limit wires to two per terminal.
Publication GMSI10-UM005C-EN-P - May 2010
32
Installing the XM-320 Position Module
Connecting an LVDT
The following figures show the wiring from a linear variable differential
transformer (LVDT) to the terminal base unit of the XM-320.
ATTENTION
You may ground the cable shield at either end of the cable.
Do not ground the shield at both ends. Recommended
practice is to ground the cable shield at the XM-320
terminal base and not at the transducer. Any convenient
Chassis terminal may be used (see Terminal Block
Assignments on page 20).
Figure 2.20 LVDT to channel 1 wiring
TYPICAL WIRING FOR LINEAR VARIABLE DIFFERENTIAL
TRANSFORMER (LVDT) TO XM-320 POSITION MODULE CHANNEL 1
Cable shield not
connected at this
end
Signal Ground
Input Signal
Signal Ground
Channel 1 Input Signal
Shield
+24V DC
Publication GMSI10-UM005C-EN-P - May 2010
0
37
Power Ground
+24V DC
Power Ground
16
22
43
6
Installing the XM-320 Position Module
33
Figure 2.21 LVDT to channel 2 wiring
TYPICAL WIRING FOR LINEAR VARIABLE DIFFERENTIAL
TRANSFORMER (LVDT) TO XM-320 POSITION MODULE CHANNEL 2
Cable shield not
connected at this
end
Signal Ground
Input Signal
Power Ground
Signal Ground
Channel 2 Input Signal
Shield
Power Ground
+24V DC
17
1
38
22
6
43
+24V DC
Connecting a Cam Potentiometer
The following figures show the wiring from a cam potentiometer to the
terminal base unit of the XM-320.
ATTENTION
You may ground the cable shield at either end of the cable.
Do not ground the shield at both ends. Recommended
practice is to ground the cable shield at the XM-320
terminal base and not at the transducer. Any convenient
Chassis terminal may be used (see Terminal Block
Assignments on page 20).
Publication GMSI10-UM005C-EN-P - May 2010
34
Installing the XM-320 Position Module
Figure 2.22 Cam potentiometer to channel 1 wiring
TYPICAL WIRING FOR CAM (VALVE) POTENTIOMETER
TO XM-320 POSITION MODULE CHANNEL 1
Cable shield
not connected
at this end
Signal Common
Channel 1 Input Signal
+24V DC
Signal
Common
Shield
16
0
37
22
+24V DC
6
Channel 1
Input Signal
28
Figure 2.23 Cam potentiometer to channel 2 wiring
TYPICAL WIRING FO R CAM (VALVE) POTEN TIOMETER
TO XM -320 POSITION M OD ULE CHANN EL 2
C able shield
not conn ecte d
at t his en d
+ 24V D C
Signal
C ommon
Signal Common
Channel 2 Input Signal
Shield
17
38
* See note
22
+24V DC
C hann el 2
I nput S ignal
28
Note: If connecting cam potentiometers to both channels 1 and 2, install jumper between
terminals 17 and 28 instead of terminals 17 and 22 in order to limit wires to two per terminal.
Publication GMSI10-UM005C-EN-P - May 2010
1
6
Installing the XM-320 Position Module
35
Connecting a Non-contact Sensor and an LVDT
The figure below shows the wiring of a non-contact sensor to channel 1 and
an LVDT to channel 2 of the XM-320.
ATTENTION
IMPORTANT
You may ground the cable shield at either end of the cable.
Do not ground the shield at both ends. Recommended
practice is to ground the cable shield at the XM-320
terminal base and not at the transducer. Any convenient
Chassis terminal may be used (see Terminal Block
Assignments on page 20).
The +24V LVDT powered from pin 25 does not utilize
the redundant power connection to the XM-320. So if
primary 24V power is lost, the +24V sensor will lose power
regardless of whether the XM-320 remains powered
through the redundant power terminals.
If redundant power is required then use a redundant power
supply (Allen-Bradley 1606-series is recommended).
Publication GMSI10-UM005C-EN-P - May 2010
36
Installing the XM-320 Position Module
Figure 2.24 Non-contact sensor and LVDT wiring
TYPICAL WIRING FOR NON-CONTACT SENSOR AND LINEAR VARIABLE
DIFFERENTIAL TRANSFORMER (LVDT) TO XM-320 POSITION MODULE
Isolated Sensor Driver
-24
SIG
COM
Cable shield not
connected at this
end
Signal Ground
Input Signal
Signal Ground
Channel 2 Input Signal
Shield
16
17
Power Ground
Power Ground
Signal Common
1 Input Signal
0 Channel
1
37
38
Shield
22
+24V DC
Shield Floating
-24V DC
6
25
28
+24V DC
PC Serial Port Connection
The XM-320 includes a serial port connection that allows you to connect a PC
to it and configure the module’s parameters. There are two methods of
connecting an external device to the module’s serial port.
• Terminal Base Unit - There are three terminals on the terminal base
unit you can use for the serial port connection. They are TxD, RxD, and
RTN (terminals 7, 8, and 9, respectively). If these three terminals are
wired to a DB-9 female connector, then a standard RS-232 serial cable
with 9-pin (DB-9) connectors can be used to connect the module to a
PC (no null modem is required).
Publication GMSI10-UM005C-EN-P - May 2010
Installing the XM-320 Position Module
37
The DB-9 connector should be wired to the terminal base unit as
follows.
XM-320 Terminal Base Unit
(Cat. No. 1440-TB-B)
DB-9 Female Connector
TX Terminal (terminal 7) ----------------------
Pin 2 (RD - receive data)
RX Terminal (terminal 8) ----------------------
Pin 3 (TD - transmit data)
RTN Terminal (terminal 9) ---------------------
Pin 5 (SG - signal ground)
• Mini-Connector - The mini-connector is located on the top of the
XM-320, as shown below.
Figure 2.25 Mini Connector
1440-TPS02-01RB
POSITION
mini-connector
A special cable (Cat. No. 1440-SCDB9FXM2) is required for this
connection. The connector that inserts into the PC is a DB-9 female
connector, and the connector that inserts into the module is a USB
Mini-B male connector.
WARNING
IMPORTANT
If you connect or disconnect the serial cable with power
applied to the module or the serial device on the other end
of the cable, an electrical arc can occur. This could cause an
explosion in hazardous location installations. Be sure that
power is removed or the area is nonhazardous before
proceeding.
If 24V Common is not referenced to earth ground, we
recommend you use an RS-232 isolator, such as Phoenix
PSM-ME-RS232/RS232-P (Cat. No. 1440-ISO-232-24), to
protect both the XM module and the computer.
Publication GMSI10-UM005C-EN-P - May 2010
38
Installing the XM-320 Position Module
DeviceNet Connection
The XM-320 includes a DeviceNet™ connection that allows the module to
communicate directly with a programmable controller, distributed control
system (DCS), or another XM module.
DeviceNet is an open, global, industry-standard communications network
designed to provide an interface through a single cable from a programmable
controller to a smart device such as the XM-320 module. As multiple XM
modules are interconnected, DeviceNet also serves as the communication bus
and protocol that efficiently transfers data between the XM modules.
Connect the DeviceNet cable to the terminal base unit as shown.
Connect
To
Terminal Base Unit
Red Wire
DNet V+
26 (optional—see note)
White Wire
CAN High
23
Bare Wire
Shield (Chassis)
10
Blue Wire
CAN Low
24
Black Wire
DNet V-
27
IMPORTANT
The DeviceNet power circuit through the XM module
interconnect, which is rated at only 300 mA, is not intended
or designed to power DeviceNet loads. Doing so could
damage the module or terminal base.
To preclude this possibility, even unintentionally, it is
recommended that DeviceNet V+ be left unconnected.
ATTENTION
ATTENTION
Publication GMSI10-UM005C-EN-P - May 2010
You must ground the DeviceNet shield at only one
location. Connecting the DeviceNet shield to terminal 10
will ground the DeviceNet shield at the XM-320 module. If
you intend to terminate the shield elsewhere, do not
connect the shield to terminal 10.
The DeviceNet network must also be referenced to earth at
only one location. Connect DNet V- to earth or chassis at
one of the XM modules.
Installing the XM-320 Position Module
ATTENTION
IMPORTANT
39
The DNet V+ and DNet V- terminals are inputs to the XM
module. Do not attempt to pass DeviceNet power through
the XM terminal base to other non-XM equipment by
connecting to these terminals. Failure to comply may result
in damage to the XM terminal base and/or other
equipment.
Terminate the DeviceNet network and adhere to the
requirements and instructions in the ODVA Planning and
Installation Manual - DeviceNet Cable System, which is
available on the ODVA web site (http://www.odva.org).
The device is shipped from the factory with the network node address (MAC
ID) set to 63. The network node address is software settable. You can use the
XM Serial Configuration Utility or RSNetWorx for DeviceNet (Version 3.0 or
later) to set the network node address. Refer to the appropriate documentation
for details.
IMPORTANT
Mounting the Module
The baud rate for the XM-320 is set by way of “baud
detection” (Autobaud) at power-up.
The XM-320 mounts on the XM-941 terminal base unit, Cat. No. 1440-TB-B.
You should mount the module after you have connected the wiring on the
terminal base unit.
ATTENTION
The XM-320 is compatible only with the XM-941 terminal
base unit. The keyswitch on the terminal base unit should
be at position 4 for the XM-320.
Do not attempt to install XM-320 modules on other
terminal base units.
Do not change the position of the keyswitch after
wiring the terminal base.
ATTENTION
This module is designed so you can remove and insert it
under power. However, when you remove or insert the
module with power applied, I/O attached to the module
can change states due to its input/output signal changing
conditions. Take special care when using this feature.
Publication GMSI10-UM005C-EN-P - May 2010
40
Installing the XM-320 Position Module
WARNING
IMPORTANT
When you insert or remove the module while power is on,
an electrical arc can occur. This could cause an explosion in
hazardous location installations. Be sure that power is
removed or the area is nonhazardous before proceeding.
Install the overlay slide label to protect serial connector and
electronics when the serial port is not in use.
1. Make certain the keyswitch (A) on the terminal base unit (C) is at
position 4 as required for the XM-320.
2. Make certain the side connector (B) is pushed all the way to the left. You
cannot install the module unless the connector is fully extended.
3. Make sure that the pins on the bottom of the module are straight so they
will align properly with the connector in the terminal base unit.
4. Position the module (D) with its alignment bar (E) aligned with the
groove (F) on the terminal base.
5. Press firmly and evenly to seat the module in the terminal base unit. The
module is seated when the latching mechanism (G) is locked into the
module.
6. Repeat the above steps to install the next module in its terminal base.
Publication GMSI10-UM005C-EN-P - May 2010
Installing the XM-320 Position Module
Module Indicators
41
The XM-320 has six LED indicators, which include a module status (MS)
indicator, a network status (NS) indicator, a status indicator for each channel
(CH1 and CH2), an activation indicator for the Setpoint Multiplier, and a
status indicator for the Relay. The LED indicators are located on top of the
module.
Figure 2.26 LED Indicators
1440-TPS02-01RB
POSITION
Module Indicators
The following tables describe the states of the LED status indicators.
Module Status (MS) Indicator
Color
State
Description
No color
Off
No power applied to the module.
Green
Flashing Red
Module performing power-up self test.
Flashing
Module operating in Program Mode1.
Solid
Module operating in Run Mode2.
Flashing
• Application firmware is invalid or not loaded.
Download firmware to the module.
Red
• Firmware download is currently in progress.
• The module power voltage is incorrect.
Solid
An unrecoverable fault has occurred. The module may
need to be repaired or replaced.
1
Program Mode - Typically this occurs when the module configuration settings are being updated with the XM
Serial Configuration Utility. In Program Mode, the module does not perform its usual functions. The signal
processing/measurement process is stopped, and the status of the alarms is set to the disarm state to prevent
a false alert or danger status.
2
Run Mode - In Run Mode, the module collects measurement data and monitors each measurement device.
Publication GMSI10-UM005C-EN-P - May 2010
42
Installing the XM-320 Position Module
Network Status (NS) Indicator
Color
State
Description
No color
Off
Module is not online.
• Module is autobauding.
• No power is applied to the module, look at Module
Status LED.
Green
Red
1
Flashing
Module is online (DeviceNet) but no connections are
currently established.1
Solid
Module is online with connections currently
established.
Flashing
One or more I/O connections are in the timed-out state.
Solid
Failed communications (duplicate MAC ID or Bus-off).
Normal condition when the module is not a slave to an XM-440, PLC, or other master device.
Channel 1 and Channel 2 Status Indicators
Color
State
Description
No Color
Off
• Normal operation within alarm limits on the channel.
• No power applied to the module, look at Module
Status LED.
Yellow
Solid
An alert level alarm condition exists on the channel
(and no transducer fault or danger level alarm condition
exists).
Red
Solid
A danger level alarm condition exists on the channel
(and no transducer fault condition exists).
Flashing
A transducer fault condition exists on the channel.
Setpoint Multiplier Indicator
Color
State
Description
Yellow
Off
Setpoint multiplier is not in effect.
Solid
Setpoint multiplier is in effect.
Relay Indicator
Publication GMSI10-UM005C-EN-P - May 2010
Color
State
Description
Red
Off
On-board relay is not activated.
Solid
On-board relay is activated.
Installing the XM-320 Position Module
Basic Operations
43
Powering Up the Module
The XM-320 performs a self-test at power-up. The self-test includes an LED
test and a device test. During the LED test, the indicators will be turned on
independently and in sequence for approximately 0.25 seconds.
The device test occurs after the LED test. The Module Status (MS) indicator is
used to indicate the status of the device self-test.
MS Indicator State
Description
Flashing Red and Green
Device self test is in progress.
Solid Green or Flashing Green
Device self test completed successfully, and the
firmware is valid and running.
Flashing Red
Device self test completed, the hardware is OK, but the
firmware is invalid. Or, the firmware download is in
progress.
Solid Red
Unrecoverable fault, hardware failure, or Boot Loader
program may be corrupted.
Refer to Module Indicators on page 41 for more information about the LED
indicators.
Manually Resetting Relays
The XM-320 has an external reset switch located on top of the module, as
shown in Figure 2.27.
Figure 2.27 Reset Switch
1440-TPS02-01RB
POSITION
Press the Reset
Switch to reset the
relays
Publication GMSI10-UM005C-EN-P - May 2010
44
Installing the XM-320 Position Module
The switch can be used to reset all latched relays in the module. This includes
the relays in the Expansion Relay Module when it is connected to the XM-320.
IMPORTANT
Publication GMSI10-UM005C-EN-P - May 2010
The Reset switch resets the relays only if the input is no
longer in alarm or the condition that caused the alarm is no
longer present.
Chapter
3
Configuration Parameters
This chapter provides a complete listing and description of the XM-320
parameters. The parameters can be viewed and edited using the XM Serial
Configuration Utility software and a personal computer. If the module is
installed on a DeviceNet network, configuring can also be performed using a
network configuration tool such as RSNetWorx (Version 3.0 or later). Refer to
your configuration tool documentation for instructions on configuring a
device.
For information about
Channel Parameters
46
Measurement Mode Parameter
49
Alarm Parameters
55
Relay Parameters
58
4-20mA Output Parameters
62
Triggered Trend Parameters
63
I/O Data Parameters
65
Data Parameters
66
Device Mode Parameters
68
IMPORTANT
45
See page
The appearance and procedure to configure the parameters
may differ in different software.
Publication GMSI10-UM005C-EN-P - May 2010
46
Configuration Parameters
Channel Parameters
The Channel parameters define the characteristics of the transducers you will
be using with the XM-320. Use the parameters to configure the transducer
sensitivity, operating range, power requirements, measurement mode, and
calibration offset. There are two instances of the parameters, one for each
channel.
TIP
The Channel LED will flash red when a transducer fault
condition exists on a channel even if you are not using the
channel. You can keep the Channel LED from flashing red
on unused channels by setting the channel’s Fault High
and Fault Low to greater than zero and less than zero,
respectively. For example, set Fault High to +18 volts and
set Fault Low to -18 volts.
Channel Parameters
Parameter Name
Description
Values/Comments
Channel Name (XM Serial
Configuration Utility only)
A descriptive name to help identify the channel in
the XM Serial Configuration Utility.
Maximum 18 characters
Sensitivity
The sensitivity of the transducer in millivolts per
Eng. Units.
This value can be found on the
transducer’s data sheet.
Eng. Units
Defines the native units of the transducer. Your
choice controls the list of possible selections
available in the Output Data Units parameter. It
also affects other module parameters, for example
the Alert and Danger Threshold, Measurement
Value, 4–20 mA Output.
Options: mils (1/1000 inch)
mm (millimeter)
degrees
%
Output Data Unit
The data units of the measured values.
The available options depend on the
Eng. Units selection.
Eng. Units
Output Data
Unit Options
mils
mils
mm
mm
mm
mils
deg
Fault High
The maximum expected DC bias voltage from the
transducer.
Fault Low
The minimum, or most negative, expected DC bias
voltage from the transducer.
Publication GMSI10-UM005C-EN-P - May 2010
deg
Volts
Note: A voltage reading outside this
range constitutes a transducer fault.
Configuration Parameters
47
Channel Parameters
Parameter Name
Description
Values/Comments
DC Bias Time Constant
The time constant used for exponential averaging
Seconds
(low pass filtering) of the transducer DC bias
measurement. The corner frequency for the low pass
filter is 1 / (2π x DC Bias Time Constant). The
greater the value entered, the longer the settling
time of the measured value to a change in the input
signal. See example table below.
Time Constant -3dB Frequency Settling
(seconds)
(Hz)
(seconds)
1
0.159
2.2
2
0.080
4.4
3
0.053
6.6
4
0.040
8.8
5
0.032
11
6
0.027
13.2
7
0.023
15.4
8
0.020
17.6
9
0.018
19.8
10
0.016
22
Target Angle
Sets the angle between the shaft and the target
surface. The target surface moves with the shaft.
The transducer is mounted perpendicular to the
target surface.
degrees
Upscale
Sets the movement of the target relative to the
transducer that is considered positive displacement.
Options: Away
Towards
Calibration Offset (XM Serial
Configuration Utility only)
Enter the position of the current Transducer DC
Bias reading.
mils
Publication GMSI10-UM005C-EN-P - May 2010
48
Configuration Parameters
Channel Parameters
Parameter Name
Description
Values/Comments
Calibration Bias
Sets the zero or green position. The zero position is
the normal operating position. Setting the zero
position compensates for the static gap. This allows
the module to display only the displacement around
the zero position.
Volts
Use one of the formulas below to calculate the
Calibration Bias. The formula that you use depends
on the Upscale setting and whether Fault High and
Fault Low are both less than or equal to zero (0).
Upscale set to “Towards” Formula
Calibration bias = Transducer DC Bias +
(Sensitivity x Calibration Offset) x sin (Target
Angle)
Upscale set to “Away” Formula
Calibration Bias = Transducer DC Bias (Sensitivity x Calibration Offset) x sin (Target
Angle)
If Fault High and Fault Low are both less than or
equal to 0, use one of these formulas:
Upscale set to “Towards” Formula
Calibration bias = Transducer DC Bias (Sensitivity x Calibration Offset) x sin (Target
Angle)
Upscale set to “Away” Formula
Calibration Bias = Transducer DC Bias +
(Sensitivity x Calibration Offset) x sin (Target
Angle)
Calculate Bias (XM Serial
Configuration Utility only)
Publication GMSI10-UM005C-EN-P - May 2010
Automatically calculates the Calibration Bias
value.
Note: Check with the manufacturer
about operating thrust position and
acceptable tolerances before making
any adjustments.
Configuration Parameters
Measurement Mode
Parameter
49
The Measurement Mode parameter controls how the two axial sensors are
used to calculate the position measurement. Use this parameter to configure
the mode of operation.
Measurement Mode
Parameter Name
XM
Configuration
Utility
EDS File
Mode
Measurement
Mode
Description
Values/Comments
Select the mode of the two axial sensors.
Options: Normal
Head-to-Head
Radial Cancel
• Normal - The two sensors are used independently
to perform two separate position measurements.
See page 49 for more information about this mode.
• Head-to-Head - The two sensors are used
together, facing each other on either side of the
target, to perform a single position measurement.
This mode can be used to extend the measurable
range beyond that of a single sensor. See page 51
for more information about this mode.
• Radial Cancel - The two sensors are used
together to perform a single position
measurement. The second sensor is set up to
measure the radial movement of the target. The
radial movement is then subtracted from the
position measurement performed by the first
sensor. See page 54 for more information about
this mode.
Normal Mode
In normal mode the module behaves as a two channel differential unit with the
probes mounted on the casing and measuring the shaft position relative to the
casing. Positioning of probes is critical to ensure that valid shaft movement
cannot at any time damage the probes. Selection of probe type and range is
obviously important. The static gaps of the probes are automatically
subtracted from the measurement in order that the system can measure small
movements relative to the total gaps.
When using this mode, the module uses straight targets, angled targets, or
mixed target types, as shown in Figure 3.1.
Publication GMSI10-UM005C-EN-P - May 2010
50
Configuration Parameters
Figure 3.1 Normal Mode
NORMAL MODE
(straight targets)
(angled targets)
(mixed targets)
The XM-320 provides monitoring facilities for the following machine
measurements when in normal mode.
•
•
•
•
Axial (thrust) Position
Differential Expansion
Case Expansion
Valve Position
IMPORTANT
Publication GMSI10-UM005C-EN-P - May 2010
For the valve position measurement, Sensitivity must be
set to "deg."
Configuration Parameters
51
Head-To-Head Mode
The head-to-head mode allows extended range operation by using two probes
in a “back to back” arrangement shown in the illustration in Figure 3.2. This
mode can be used when the machine does not have enough space for larger
diameter probes. It is not necessary for the scales to be symmetrical in this
mode, and probes of different voltage sensitivities can be used within the one
module.
Figure 3.2 Head-to-Head Mode
HEAD TO HEAD MODE
(one target)
(two targets)
In head-to-head mode, the XM-320 provides monitoring facilities for
complementary differential expansion measurements.
TIP
In head-to-head mode, all position measurements are
stored in channel 1.
Head-to-Head Example
This head-to-head application measures a total displacement of 1000 mils on a
shaft collar using two 500 mil probes with a standard sensitivity of 30mV/mil
(or 0.030V/mil). See Figure 3.3.
Publication GMSI10-UM005C-EN-P - May 2010
52
Configuration Parameters
Figure 3.3 Head-to-Head Mode
Note: The direction of differential growth for an upscale reading is away from Probe A and towards
Probe B.
The chart below shows gap-to-instrument reading-to-voltage outputs for
typical 500 mil transducers with an offset of 150 mils. Note that the offset gap
of a transducer is the gap closest to the transducer where the transducer’s
response to gap change becomes non-linear and not useful for measurement.
Probe A
Probe B
Gap
Reading
Voltage
Gap
Reading
Voltage
150
0
-2.8
150
0
-3
250
100
-5.8
250
100
-6
400
250
-10.3
400
250
-10.5
550
400
-14.8
550
400
-15
650
500
-17.8
650
500
-18
IMPORTANT
Make certain the shaft is in its correct cold position or
compensate for the actual shaft axial position if it is known.
You can put the shaft into position by mechanically moving
it up against the active thrust shoe, or use the actual thrust
position to offset the transducer gap settings so that they
will be correct when the rotor is in the cold position.
Install and gap the probes for their cold gap settings using the information
provided from previous installations or data provided in the Turbine manual.
This example assumes that the correct cold set point (Green line) is 250 mils,
the rotor is placed against the active thrust shoes, and the measurement range
is 0 to 1000 mils.
Publication GMSI10-UM005C-EN-P - May 2010
Configuration Parameters
53
Calculate and set the transducers as follows:
1. To determine the placement of Probe A, add the Cold Set Point to the
Transducer Offset, then add the Axial Position from the Active Face.
Probe A Gap = 250 + 150 + 0 = 400 mils
2. To determine the placement of Probe B, subtract the Cold Set Point
from the Full Scale Reading, then add the Transducer Offset and the
Axial Position from the Active Face.
Probe B Gap = 1000 – 250 + 150 + 0 = 900
3. Enter the following data on the Channels property page in the XM-320
Position Module Configuration Tool.
Channel 1 (Probe A)
Channel 2 (Probe B)
Sensitivity
30
Sensitivity
30
Eng. Units
mils
Eng. Units
mils
Output Data Unit
mils
Output Data Unit
mils
Fault Low
-181
Fault Low
-18.21
Fault High
-2.62
Fault High
-2.82
DC Bias Time Constant
1
DC Bias Time Constant
1
Target Angle
90
Target Angle
90
Upscale
Away
Upscale
Towards
Calibration Offset
250
Calibration Offset
1000
Calibration Bias
Press
Calculate
Bias
Calibration Bias
-33 (You
must enter
value using
formula
below)
Mode
Head-to-Head
1
This value is .2 volts below the lowest voltage the transducer will output for this measurement taken from the
calibration chart.
2
This value is .2 volts above the highest voltage the transducer will output for this measurement taken from the
calibration chart.
Publication GMSI10-UM005C-EN-P - May 2010
54
Configuration Parameters
Calibration Bias Calculation
Since Probe B is gapped beyond the operating range, you must manually
calculate the calibration bias as well as the transducer DC bias.
1. To determine the Transducer DC Bias, subtract Position B Gap from
Transducer Offset, multiply by the Sensitivity and then add the
Transducer Offset voltage.
Transducer DC Bias = 0.03 × ( 150 – 900 ) – 3 = -25.5
2. Use the following formula to calculate the Calibration Bias:
Calibration Bias = Transducer DC Bias – ( Sensitivity × Calibration Offset ) × sin (Target Angle)
Calibration Bias = -25.5 – ( 0.03 × 250 ) × sin(90) = -33
IMPORTANT
The formula used to calculate the Calibration Bias depends
on the Upscale setting and whether Fault High and Fault
Low are less than or equal to zero (0). Press F1 on the
Channels property page for a description of the formulas.
Radial Cancel Mode
In radial cancel mode, the movement of the shaft is detected by measuring the
gap between the probe tip and a ramp of known and consistent angle to the
center line of the shaft. If two ramps are present they should be measured as
shown below. The potential "lift" error of shaft position caused by jacking oil
pressure is eliminated in the module calculations.
Where only one ramp is available, the "lift" error must be taken into account,
and this is achieved by using a second probe operating on a portion of the
shaft which is parallel to the center line.
Publication GMSI10-UM005C-EN-P - May 2010
Configuration Parameters
55
Figure 3.4 Radial Cancel Mode
RADIAL CANCEL MODE
(two angles)
radial
movement
axial movement
(one angle)
The XM-320 provides monitoring facilities for the following machine
measurements when in radial cancel mode.
• Standard Single Ramp Differential Expansion
• Non-standard Single Ramp Differential Expansion
• Dual Ramp Differential Expansion
TIP
Alarm Parameters
In radial cancel mode, all position measurements are stored
in channel 1.
The Alarm parameters control the operation of the alarms (alert and danger
level) and provide alarm status. The XM-320 provides two alarms, one per
channel. Use these parameters to configure the alarms.
Alarm Parameters
Parameter Name
Description
Values/Comments
Number (1-2) (XM Serial
Configuration Utility only)
Sets the alarm to be configured in the XM Serial
Configuration Utility. There are two alarms in the
XM-320, one for each channel.
Options: 1 (Channel 1 alarm)
2 (Channel 2 alarm)
Name (XM Serial Configuration
Utility only)
A descriptive name to identify the alarm in the XM
Serial Configuration Utility.
Maximum 18 characters
Enable
Enable/disable the selected alarm.
Note: The Alarm Status is set to Disarm when the
alarm is disabled.
XM Configuration
Utility
EDS Filet
Check to Enable
Enabled
Clear to Disable
Disabled
Publication GMSI10-UM005C-EN-P - May 2010
56
Configuration Parameters
Alarm Parameters
Parameter Name
Description
Values/Comments
Condition
Controls when the alarm should trigger.
Options: Greater Than
Less Than
Inside Range
Outside Range
• Greater than - Triggers the alarm when the
measurement value is greater than or equal to the
Alert and Danger Threshold values.
The Danger Threshold value must be greater than
or equal to the Alert Threshold value for the trigger
to occur.
• Less than - Triggers the alarm when the
measurement value is less than or equal to the
Alert and Danger Threshold values.
The Danger Threshold value must be less than or
equal to the Alert Threshold value for the trigger to
occur.
• Inside range - Triggers the alarm when the
measurement value is equal to or inside the range
of the Alert and Danger Threshold values.
The Danger Threshold (High) value must be less
than or equal to the Alert Threshold (High) value
AND the Danger Threshold (Low) value must be
greater than or equal to the Alert Threshold (Low)
value for the trigger to occur.
• Outside range - Triggers the alarm when the
measurement value is equal to or outside the
range of the Alert and Danger Threshold values.
The Danger Threshold (High) value must be greater
than or equal to the Alert Threshold (High) value,
AND the Danger Threshold (Low) value must be
less than or equal to the Alert Threshold (Low)
value for the trigger to occur.
Alert Threshold (High)
The threshold value for the alert (alarm) condition.
Note: This parameter is the greater (High) threshold
value when Condition is set to "Inside Range" or
"Outside range."
Danger Threshold (High)
The threshold value for the danger (shutdown)
condition.
Same measurement unit as Output
Data Unit selection for specified
channel.
Same measurement unit as Output
Data Unit selection for specified
channel.
Note: This parameter is the greater (High) threshold
value when Condition is set to "Inside Range" or
"Outside Range."
Alert Threshold (Low)
The lesser threshold value for the alert (alarm)
condition.
Same measurement unit as Output
Data Unit selection for the specified
channel.
Note: This value is not used when Condition is set
to "Greater Than" or "Less Than."
Danger Threshold (Low)
The lesser threshold value for the danger (shutdown)
condition.
Note: This value is not used when Condition is set
to "Greater Than" or "Less Than."
Publication GMSI10-UM005C-EN-P - May 2010
Same measurement unit as Output
Data Unit selection for the specified
channel.
Configuration Parameters
57
Alarm Parameters
Parameter Name
Description
Values/Comments
Hysteresis
The amount that the measurement value must fall
(below the threshold) before the alarm condition is
cleared. For example, Alert Threshold = 120 and
Hysteresis = 2. The alarm (alert) activates when the
measured value is 120 and will not clear until the
measured value is 118.
Same measurement unit as Output
Data Unit selection for the specified
channel.
Note: The Alert and Danger Thresholds use the
same hysteresis value.
Note: For the Outside Range condition, the
hysteresis value must be less than Alert Threshold
High – Alert Threshold Low.
Startup Period
The length of time that the Threshold Multiplier is
applied to the thresholds. The startup period begins
when the setpoint multiplier switch is reopened
(pushbutton disengaged or toggle switch flipped to
off).
Enter a value from 0 to 1092 minutes,
adjustable in increments of 0.1
minutes.
Threshold Multiplier
The action to take when the setpoint multiplier
switch is closed (pushbutton engaged or toggle
switch flipped to on) and during the startup period
once the switch is reopened. The module applies the
multiplier to the alarm thresholds during this time to
avoid false alarms at resonance frequencies.
Enter any fractional value between 0
and 10.
Enter 0 (zero) to disabled the alarm
during the startup period.
Note: The multiplication may have the opposite of
the intended affect under certain circumstances. For
example, if the Condition is set to "Less Than" and
the thresholds are positive, then multiplication of the
threshold values increases the likelihood of the
measured value being within the alarm range.
Therefore, you may want to disable the alarms
during the startup period.
Publication GMSI10-UM005C-EN-P - May 2010
58
Configuration Parameters
Relay Parameters
The Relay parameters control the operation of the on-board relay, as well as
the relays on the Expansion Relay (XM-441) module. Use these parameters to
configure which alarm(s) the relay is associated with as well as the behavior of
the relay.
IMPORTANT
A relay can be defined, regardless of whether or not it is
physically present. A non-physical relay is a virtual relay.
When a relay (physical or virtual) activates, the module
sends a Change of State (COS) message to its master,
which acts on the condition as necessary. An XM-440
Master Relay Module can activate its own relays in response
to a relay (physical or virtual) activation at any of its slaves.
Relay Parameters
Parameter Name
Description
Values/Comments
Number (XM Serial Configuration
Utility only)
Sets the relay to be configured in the XM Serial
Configuration Utility.
Number 1 is the on-board relay.
Numbers 2 through 5 are either relays
on the Expansion Relay module when
it’s connected to the module or virtual
relays.
Virtual relays are non-physical relays.
Use them when you want the effect of
the relay (monitor alarms, activation
delay, and change status) but do not
need an actual contact closure. For
example, a PLC or controller
monitoring the relay status.
Note: The Relay Installed parameter
indicates whether a relay is a virtual
relay or a physical relay on a module.
Name (XM Serial Configuration
Utility only)
A descriptive name to help identify the relay in the
XM Serial Configuration Utility.
Enable
Enable/disable the selected relay.
Note: The Relay Current Status is set to "Not
Activated" when the relay is disabled. See page 66.
Publication GMSI10-UM005C-EN-P - May 2010
Maximum 18 characters
XM Configuration
Utility
EDS File
Check to Enable
Enabled
Clear to Disable
Disabled
Configuration Parameters
59
Relay Parameters
Parameter Name
Description
XM Configuration EDS File
Utility
Latching
Latching
Option
XM Configuration EDS File
Utility
Logic
XM Configuration EDS File
Utility
Alarm A/B
XM Configuration
Utility
EDS File
Check means
latching (relay must
be explicitly reset)
Latching
Clear means
non-latching (relay
is reset once the
alarm condition has
passed
Nonlatching
Enter a value from 0 to 25.5 seconds,
Enter the length of time for which the Activation
Logic must be true before the relay is activated. This adjustable in increments of 0.1
seconds.
reduces nuisance alarms caused by external noise
and/or transient vibration events.
Default is 1 second
Activation Delay
Activation Logic
Controls whether an explicit reset is required to
deactivate the relay after the alarm subsides.
Values/Comments
Alarm
Identifier
A/B
Options: A only
A or B
A and B
• A or B - Relay is activated when either Alarm A or
Alarm B meets or exceeds the selected Alarm
Status condition(s).
• A and B - Relay is activated when both Alarm A
and Alarm B meet or exceed the selected Alarm
Status condition(s).
• A Only - Relay is activated when Alarm A meets
or exceeds the selected Alarm Status
condition(s).
Sets the relay activation logic.
Sets the alarm(s) that the relay will monitor. The
alarm must be from the same device as the relay.
When the Activation Logic is set to "A and B" or "A
or B," you can select an alarm in both Alarm A and
Alarm B. The system monitors both alarms. When
the Activation Logic is set to "A only," you can
select an alarm only in Alarm A.
Alarm Number 1 or 2
Note: You can only select an alarm
that is enabled.
Publication GMSI10-UM005C-EN-P - May 2010
60
Configuration Parameters
Relay Parameters
Parameter Name
XM Configuration EDS File
Utility
Alarm Status to
Activate On
Description
Values/Comments
Sets the alarm conditions that will cause the relay to
activate. You can select more than one.
Options: Normal
Danger
Xdcr Fault
Alert
Disarm
Module Fault
Alarm Levels • Normal - The current measurement is not in
excess of any alarm thresholds.
• Alert - The current measurement is in excess of
the alarm level threshold(s) but not in excess of the
Check means enable.
danger level threshold(s).
• Danger - The current measurement is in excess of Clear means disable.
the danger level threshold(s).
• Disarm-The alarm is disabled or the device is in
Program mode.
• Xdcr Fault - A transducer fault is detected on the
associated transducer.
• Module Fault - Hardware or firmware failure, or
an error has been detected and is preventing
proper operation of the device.
Relay Installed
Indicates whether the relay is a physical relay on a
module or a virtual relay. If the relay is a physical
relay, then you can set the Failsafe parameter.
If the relay is a virtual relay, the Failsafe parameter
is not used or it is disabled.
XM Configuration
Utility
EDS File
Check = Physical
Relay
Installed =
Physical Relay
Clear = Virtual Relay Not Installed =
Virtual Relay
Publication GMSI10-UM005C-EN-P - May 2010
Configuration Parameters
61
Relay Parameters
Parameter Name
Description
XM Configuration EDS File
Utility
Failsafe Relay
Failsafe
Option
Values/Comments
Controls whether the relay is failsafe or nonfail-safe.
Failsafe operation means that when in alarm, the
relay contacts are in their "normal," de-energized, or
"shelf-state" positions. In other words, normally
closed relays are closed in alarm, and normally open
relays are open in alarm. With failsafe operation, a
power failure equals an alarm.
XM Configuration
Utility
EDS File
Check = Failsafe
Failsafe
Clear = Nonfail-safe Nonfailsafe
The following are true of a relay in failsafe
operation:
• The relay is energized when power is applied to
the module.
• The relay in a nonalarmed condition has power
applied to the coil.
• In alarm condition, power is removed from the
relay coil, causing the relay to change state.
For nonfail-safe operation, the following are true:
• Under nonalarm conditions, the relay closes the
circuit between the common and the N.C.
(normally closed) terminals.
• Under alarm conditions, the relay changes state to
close the circuit between the common and the
N.O. (normally open) terminals.
For failsafe operation, the following are true:
• Under nonalarm (with power applied to the unit)
conditions, the relay closes the circuit between the
common and the N.O. terminals.
• Under alarm or loss-of-power conditions, the relay
changes state to close the circuit between the
common and the N.C. terminals.
Publication GMSI10-UM005C-EN-P - May 2010
62
Configuration Parameters
4-20mA Output Parameters
The 4-20mA output parameters define the characteristics of the two 4-20mA
output signals. The parameters are the same for each output.
4-20mA Parameters
Parameter Name
Description
Values/Comments
Enable
Enables/disables the 4-20 mA output.
Min Range
The measured value associated with the 4 mA.
Max Range
The measured value associated with the 20 mA.
IMPORTANT
IMPORTANT
XM Configuration
Utility
EDS File
Check to Enable
Enabled
Clear to Disable
Disabled
Same measurement unit as Output
Data Unit selection for the specified
channel.
Measured values between Min Range and Max Range are
scaled into the range from 4.0 to 20.0 to produce the
output value. The Min Range value does not have to be
less than the Max Range value. If the Min Range value is
greater than the Max Range value, then the output signal
is effectively inverted from the input signal.
The 4-20mA outputs are either on or off. When they are
on, the 4-20mA outputs overshoot the 4 and 20mA limits
by 10% when the measurement exceeds the minimum and
maximum range. This means the minimum current
produced is 3.6mA and the maximum current produced is
22mA.
When the 4-20mA outputs are off, they produce a current
approximately 2.9mA. The 4-20mA outputs are off under
the following conditions:
• The 4-20mA outputs are set to "Disable" (see Enable
above).
• The module is in Program mode.
• A transducer fault occurs that affects the corresponding
measurement.
Publication GMSI10-UM005C-EN-P - May 2010
Configuration Parameters
Triggered Trend Parameters
63
The XM-320 can collect a triggered trend. A triggered trend is a time-based
trend that is collected when a relay on the XM-320 is activated, or the module
receives a trigger event.
Once the triggered trend is configured, the XM-320 continuously monitors the
trended measurements. When a trigger occurs, the XM-320 collects additional
data as specified by the Post Trigger parameter.
The XM-320 can only store one triggered trend. Unless the triggered trend is
latched, the trend data is overwritten with new data when the next trigger
occurs.
The triggered trend parameters define the trend data that is collected by the
module. Use these parameters to select the measurements included in the
trend records, the interval between trend records, and which relay triggers
(activates) the collection of the trend data.
IMPORTANT
The Triggered Trend parameters are not included in the
EDS file and cannot be edited using generic configuration
tools such as RSNetWorx for DeviceNet.
Triggered Trend Parameters
Parameter Name
Description
Values/Comments
Enable Triggered Trend
Measurements
Enable/disable the triggered trend measurements.
Select to configure the triggered trend
measurements.
Check to enable.
Clear to disable.
Select Measurements
Sets the measurements to be collected and stored in
the module.
More than one measurement can be
selected.
Number of Records
The maximum number of measurement sets that can
be collected in the trend buffer. The measurement
sets make up the trend data.
The Number of Records is
automatically calculated based upon
the number of Trended
Measurements selected.
Latch Enable
Determines whether the trigger trend is latched or
unlatched.
Check means latched
Clear means unlatched
Latched means that subsequent triggers are ignored
after the initial trigger. This prevents the trend data
from being overwritten with new data until the
trigger is manually reset (click Reset Trigger button).
Unlatched means that the trend data is overwritten
with new data every time a trigger occurs.
Publication GMSI10-UM005C-EN-P - May 2010
64
Configuration Parameters
Triggered Trend Parameters
Parameter Name
Description
Values/Comments
Relay Number
Sets the relay that triggers the trend to be collected. None means that the trend can only be
triggered manually or by a trigger
event (for example, XM-440).
Relay Number 1 is the on-board relay.
Numbers 2 through 5 are either relays
on the Expansion Relay module when
it’s connected to the module or virtual
relays.
Note: The relay must be enabled.
Refer to Relay Parameters on page 58.
Record Interval
The amount of time between consecutive trend
records.
1 to 3600 seconds
Note: If you enter a Record Interval, the Trend Span
is automatically updated.
Trend Span
The total amount of time that can be covered by the
trend data (Number of Records x Record
Interval).
Seconds
Note: If you edit the Trend Span, the Record
Interval is automatically updated.
Post Trigger
The percentage of records to be collected once the
trigger occurs. For example, if you set Post Trigger to
20%, then 80% of the records in the trend are before
the trigger occurs, and 20% of the records in the
trend are after the trigger occurs.
0 to 100 Percent
This allows you to evaluate what happened after the
trigger occurred.
Status
Shows the status of the trend data.
Possible status values:
• Not collected - No trend data is
currently collected.
• Collecting - A trigger has occurred
and data (including post-trigger
data) is being collected.
• Collected - A trend has been saved
to the buffer and is available to view
and upload.
View Trend Data
Displays a plot of the collected trend data.
Reset Trigger
Resets the trigger if Latch enabled is selected. This
allows the module to overwrite the previous trend
data when the next trigger occurs.
Manual Trigger
Triggers the module to collect the trend data without
relay activation.
Publication GMSI10-UM005C-EN-P - May 2010
Configuration Parameters
I/O Data Parameters
65
The I/O data parameters are used to configure the content and size of the
DeviceNet I/O Poll response message.
IMPORTANT
The XM module must be free of Poll connections when
configuring the Poll Output (Poll Response Assembly)
and Poll Size. Any attempt to download the parameters
while a master device has established the Poll connection
with the XM module will result in an error.
To close an existing Poll connection with an XM-440,
switch the XM-440 from Run mode to Program mode.
Refer to Changing Operation Modes on page 73.
To close an existing Poll connection with other master
devices, remove the module from the scan list or turn off
the master device.
I/O Data Parameters
Parameter Name
Description
Values/Comments
COS Size (XM Serial
Configuration Utility only)
The size (number of bytes) of the Change of State
(COS) message.
The COS Size cannot be changed.
COS Output (XM Serial
Configuration Utility only)
The Assembly instance used for the COS message.
The COS message is used to produce the Alarm and
Relay status for the module.
The COS Output cannot be changed.
Refer to COS Message Format on
page 78 for more information.
Poll Size
The size (number of bytes) of the Poll response
message.
XM Configuration EDS File
Utility
Poll Output
Poll
Response
Assembly
Options: Assembly Instance 101
Sets the Assembly instance used for the Poll
Custom Assembly
response message. Each Assembly instance contains
a different arrangement of the Poll data.
Refer to Poll Message Format on page
77 for more information.
The Poll response message is used by the XM
module to produce measured values. It can contain
up to 31 REAL values for a total of 124 bytes of data.
Assembly Instance Table (XM
Serial Configuration Utility only)
Displays the format of the currently selected COS or
Poll Assembly instance.
The highlighted (yellow) Assembly
structure bytes are included in the I/O
message.
Custom Assembly (XM Serial
Configuration Utility only)
Defines a custom data format for the Poll response.
The custom assembly can contain any of the
measurement parameters included in Assembly
instance 101, as well as alarm and relay
configuration parameters.
You can select up to 20 parameters.
Refer to Poll Message Format on page
77 for more information.
Publication GMSI10-UM005C-EN-P - May 2010
66
Configuration Parameters
The Data parameters are used to view the measured values of the input
channels and the 4–20mA outputs, as well as to monitor the status of the
channels, alarms, and relays.
Data Parameters
TIP
To view all the data parameters in the XM Serial
Configuration Utility, click the View Data tab.
Channel Data
Channel Data Parameters
Parameter Name
Description
Channel Status
States whether a fault condition exists. If a fault
exists, the measurement value may not be accurate.
Measurement Value
Shows the current measurement value for the
channel.
XM Configuration EDS File
Utility
Transducer Fault
States whether a transducer fault exists.
Transducer
Status
Transducer DC Bias
Shows the measured average DC offset of the
transducer signal. This value is compared with Fault
High and Fault Low to determine whether the
transducer is working properly.
4-20mA Output A and B (XM
Serial Configuration Utility only)
Shows the current output value in the range of 4.0 to
20.0mA.
Publication GMSI10-UM005C-EN-P - May 2010
Values/Comments
Possible status values: No Fault
Fault
Configuration Parameters
67
Alarm and Relay Status
Alarm and Relay Status Parameters
Parameter Name
Description
Values/Comments
Alarm Status
States the current status of the alarm.
Possible status values.
• Normal - The alarm is enabled, the
device is in Run mode, there is no
transducer fault, and the current
measurement is not within the Alert
or Danger Threshold value(s).
• Alert - The alarm is enabled, the
device is in Run mode, there is no
transducer fault, and the current
measurement is in excess of the
Alert Threshold value(s) but not in
excess of the Danger Threshold
value(s).
• Danger - The alarm is enabled, the
device is in Run mode, there is no
transducer fault, and the current
measurement is in excess of the
Danger Threshold value(s).
• Disarm-The alarm is disabled or the
device is in Program mode.
• Transducer Fault - The alarm is
enabled, the device is in Run mode,
and a transducer fault is detected on
the associated transducer.
• Module Fault - Hardware or
firmware failure, or an error has
been detected and is preventing
proper operation of the device.
Relay Status
States the current status of the relay.
Possible status values: Activated
Not Activated
Publication GMSI10-UM005C-EN-P - May 2010
68
Configuration Parameters
Device Mode Parameters
The Device Mode parameters are used to control the functions and the
behavior of the device.
IMPORTANT
The XM Serial Configuration Utility handles these
parameters automatically and transparently to the user.
Device Mode Parameters
Parameter Name
Description
Values/Comments
Device Mode
Sets the current operation mode of the device. Refer
to Changing Operation Modes on page 73 for more
information.
Options: Run Mode
Program Mode
Autobaud
Enables/disables autobaud.
Options: Enabled
Disabled
When autobaud is set to "Enabled," the module will
listen to other devices on the network to determine
the correct baud rate to use for communications.
When autobaud is set to "Disabled," the module
baud rate must be set manually.
Publication GMSI10-UM005C-EN-P - May 2010
Appendix
A
Specifications
Appendix A lists the technical specifications for the XM-320 Position Module.
XM-320 Technical Specifications
Product Feature
Specification
Communications
DeviceNet Standard DeviceNet protocol for all
functions
NOTE: The XM-320 uses only the DeviceNet
protocol, not power. Module power is provided
independently.
Available Electronic Data Sheet (EDS) file
provides support for most DeviceNet
compliant systems
Baud rate automatically set by bus master
to 125kb, 250kb, 500kb
Side Connector All XM measurement and relay modules
include side connectors that allow
interconnecting adjacent modules, thereby
simplifying the external wiring
requirements.
The interconnect provides primary power,
DeviceNet communications, and the circuits
necessary to support expansion modules,
such as the XM-441 Expansion Relay
module.
Serial RS-232 via mini-connector or terminal base
unit
Baud rate fixed at 19200
NOTE: Local configuration via Serial
Configuration Utility.
Inputs
2 Channels Eddy current transducer signals
Linear variable differential transformer
Voltage signals from any position
measurement sensor
Transducer Power Isolated 24 Volts that can be wired to be
either +24V or -24V
Voltage Range Selectable in software between -24V and
+24V
Sensitivity User configurable in software
Input Impedance Greater than 100kohm
69
Publication GMSI10-UM005C-EN-P - May 2010
70
Specifications
XM-320 Technical Specifications
Product Feature
Specification
Outputs
4-20mA Outputs Two isolated outputs
600 ohm max load
Buffered Outputs 2 outputs; 1 per channel
Indicators
6 LEDs Module Status - red/green
Network Status - red/green
Channel 1 Status - yellow/red
Channel 2 Status - yellow/red
Setpoint Multiplier - yellow
Relay - red
Measurement Modes
Normal (two independent channels)
Head-to-head
Radial cancel
Delta Time Buffer
Number of Records 2048
Delta Time Interval 1 to 3600 seconds
Trigger Mode Relay on the XM-320 module is activated,
or by a trigger event (for example,
DeviceNet command from a controller or
host)
The data collected in the buffer is user
configurable.
Alarms
Number 2 alarm and danger pairs
Operators Greater than
Less than
Inside range
Outside range
Hysteresis User configurable in software
Startup Inhibit/Setpoint Multiplication Period: 0 to 1092 minutes, adjustable in 0.1
minute increments
Inhibit/multiplication function: Multiply by
N (0 to 10, 0 = Disarm)
Relays
Number Single on-board relay, two sets of contacts DPDT (2 Form C)
Four additional relays when interconnected
to an XM-441 Expansion Relay module, or
Four virtual relays whose status can be
used by remote Control Systems or the
XM-440 Master Relay module
Publication GMSI10-UM005C-EN-P - May 2010
Specifications
71
XM-320 Technical Specifications
Product Feature
Specification
On-board Relay Rating Maximum Voltage: 125V dc, 125V ac
Maximum Current: 3.5A*
Minimum Current: 0
Maximum Power: 60W, 62.5VA
*Max current is up to 40°C, then derates to 2A at
65°C.
Agency Rating:
120V ac @ 0.5A
110V dc @ 0.3A
30V dc @ 1.0A
Failsafe Normally energized (failsafe), or
Normally de-energized (non-fail-safe)
Latching Latching, or
Non-latching
Time Delay 0 to 25.5 seconds, adjustable in 100msec
increments
Voting Logic Single or paired "And" or "Or" logic applied
to any alarm
Reset Local reset switch on top of module
Remote reset switch wired to terminal base
Digital reset command via serial or
DeviceNet interface
Activation On Alarm Status:
Normal
Alert
Danger
Disarm
Transducer fault
Module fault
Non-Volatile Configuration
A copy of the module configuration is
retained in non-volatile memory from where
it is loaded upon power up*.
*The configuration stored in non-volatile
memory can be deleted only by a module-reset
command sent via the serial interface, using
the Serial Configuration Utility, or via
DeviceNet from any compliant software
application.
Power
Module +21.6 to 26.4V dc
Consumption Maximum: 200mA
Typical: 165mA
Publication GMSI10-UM005C-EN-P - May 2010
72
Specifications
XM-320 Technical Specifications
Product Feature
Specification
Heat Production Maximum: 5.28 Watts (18 BTU/hr)
Typical: 3.96 Watts (13.5 BTU/hr)
Transducer Isolated 24V dc, user configurable with
wiring
Environmental
Operating Temperature -20 to +65°C (-4 to +149°F)
Storage Temperature -40 to +85°C (-40 to +185°F)
Relative Humidity 95% non-condensing
All printed circuit boards are conformally coated
in accordance with IPC-A-610C.
Physical
Dimensions Height: 3.8in (97mm)
Width: 3.7in (94mm)
Depth: 3.7in (94mm)
Terminal Screw Torque 7 pound-inches (0.6Nm)
Approvals
(when product or packaging is marked)
UL
UL Listed for Ordinary
Locations
UL
UL Listed for Class I, Division 2
Group A, B, C, and D Hazardous
Locations
CSA
CSA Certified Process Control
Equipment
CSA
CSA Certified Process Control
Equipment for Class I, Division
2 Group A, B, C, and D
Hazardous Locations
EEX*
European Union 94/9/EEC ATEX
Directive, compliant with EN
50021; Potentially Explosive
Atmospheres, Protection “n”
CE*
European Union 89/336/EEC
EMC Directive
C-Tick*
Australian
Radiocommunications Act,
compliant with:
AS/NZS 2064, Industrial
Emissions
*See the Product Certification link at
www.rockwellautomation.com for Declarations
of Conformity, Certificates and other
certification details.
Publication GMSI10-UM005C-EN-P - May 2010
Appendix
B
DeviceNet Information
Electronic Data Sheets
Electronic Data Sheet (EDS) files are simple text files used by network
configuration tools such as RSNetWorx (Version 3.0 or later) to help you
identify products and easily commission them on a network. The EDS files
describe a product’s device type, product revision, and configurable parameters
on a DeviceNet network.
The EDS files for the XM modules are installed on your computer with the
XM configuration software. The latest EDS files can also be obtained at
http://www.ab.com/networks/eds/ or by contacting your local Rockwell
Automation representative.
Refer to your DeviceNet documentation for instructions on registering the
EDS files.
Changing Operation Modes
XM modules operate in two modes.
Mode
Description
Run
The XM measurement modules collect measurement data and
monitor each measurement device.
The XM-440 establishes I/O connections with the XM
measurement modules in its scan list and monitors their alarms,
and controls its own relay outputs accordingly.
Program
The XM module is idle.
The XM measurement modules stop the signal
processing/measurement process, and the status of the alarms
is set to the disarm state to prevent a false alert or danger
status.
The XM-440 closes the I/O connections with the XM
measurement modules in its scan list and stops monitoring their
alarms; relays are deactivated unless they are latched.
Configuration parameters can be read, updated and downloaded
to the XM module.
To change the operation mode of the module, use the Device Mode parameter
in the EDS file. Note that the Stop and Start services described on page 75 can
also be used to change the operation mode.
IMPORTANT
73
The XM Serial Configuration Utility software automatically
puts XM modules in Program mode and Run mode
without user interaction.
Publication GMSI10-UM005C-EN-P - May 2010
74
DeviceNet Information
Transition to Program Mode
Parameter values can only be downloaded to an XM module while the module
is in Program mode. Any attempt to download a parameter value while the
module is in Run mode will result in a Device State Conflict error.
To transition an XM module from Run mode to Program mode on a
DeviceNet network, set the Device Mode parameter to "Program mode" and
click Apply. Note that you cannot change any other parameter until you have
downloaded the Program mode parameter.
TIP
The Module Status indicator flashes green when the
module is in Program mode.
Refer to your DeviceNet documentation for specific instructions on editing
EDS device parameters.
TIP
You can also use the Stop service described on page 75 to
transition XM modules to Program mode.
Transition to Run Mode
In order to collect data and monitor measurement devices, XM modules must
be in Run mode. To transition an XM module from Program mode to Run
mode on a DeviceNet network, set the Device Mode parameter to "Run
mode" and click Apply.
TIP
The Module Status indicator is solid green when the
module is in Run mode.
Refer to your DeviceNet documentation for specific instructions on editing
EDS device parameters.
TIP
Publication GMSI10-UM005C-EN-P - May 2010
You can also use the Start service described on page 75 to
transition XM modules to Run mode.
DeviceNet Information
75
The table below defines the services supported by the XM modules. The table
includes the service codes, classes, instances, and attributes by their
appropriate hexadecimal codes. Use the Class Instance Editor in RSNetWorx
to execute these services, as illustrated in the example below.
XM Services
XM Services
Service Code
(Hex)
Class
(Hex)
Transition to Run Mode
Start
(06)
Transition to Program Mode
Action
Instance
Attribute
Data
Device Mode Object
(320)
1
None
None
Stop
(07)
Device Mode Object
(320)
1
None
None
Save configuration to
non-volatile memory (EEPROM)
Save
(16)
Device Mode Object
(320)
1
None
None
Delete saved configuration from
non-volatile memory (EEPROM)
Delete
(09)
Device Mode Object
(320)
1
None
None
Reset a specific latched relay
Reset
(05)
Relay Object
(323)
Relay number
1-C for XM-440,
1-5 for XM-12X,
XM-320 and
XM-220, 1-8 for
XM-36X and
XM-16X
None
None
Reset all latched relays
Reset
(05)
Relay Object
(323)
0
None
None
Reset the Peak Speed (XM-12X
only)
Reset
(05)
Speed Measurement
Object
(325)
1, 2 for XM-220
None
None
Close the virtual setpoint
multiplier switch to activate the
alarm setpoint multipliers (not
applicable to all XM modules)
Other
(33)
Discrete Input Point
Object
(08)
1
None
None
Open the virtual setpoint
multiplier switch to start the
setpoint multiplier timers and
eventually cancel alarm setpoint
multiplication (not applicable to
all XM modules)
Other
(32)
Discrete Input Point
Object
(08)
1
None
None
Publication GMSI10-UM005C-EN-P - May 2010
76
DeviceNet Information
Example
To save the configuration parameters to the non-volatile memory (EEPROM),
fill in the Class Instance Editor as shown below.
Clear Send the attribute
ID and then enter the
Class (320 hex) and
Instance (1)
Select the Save
service code
Click Execute to
initiate the
action
Invalid Configuration Errors
A Start or Save service request to an XM module may return an Invalid Device
Configuration error when there is a conflict amongst the configuration
settings.
The general error code for the Invalid Device Configuration error is D0hex.
An additional error code is returned with the general error code to specify
which configuration settings are invalid. The table below lists the additional
error codes associated with the Invalid Device Configuration error.
Additional Error Codes returned with the Invalid Device Configuration Error (0xD0)
Publication GMSI10-UM005C-EN-P - May 2010
Error Code
(Hex)
Description
01
No specific error information is available.
02
Mismatched transducer, channel, and/or measurement unit.
03
Inverted transducer fault high/low values.
04
Alarm thresholds conflict with the alarm condition.
05
Alarm speed range is invalid.
06
Band minimum frequency is greater than maximum frequency. Or,
maximum frequency is greater than FMAX.
07
Relay is associated with an alarm that is not enabled.
08
Tachometer must be enabled for alarm or channel settings.
09
A senseless speed range is enabled on a speed alarm.
DeviceNet Information
77
Additional Error Codes returned with the Invalid Device Configuration Error (0xD0)
XM-320 I/O Message
Formats
Error Code
(Hex)
Description
0A
Too many alarms associated with a single measurement.
0B
Invalid node address in the alarm list.
0C
Too many alarms in the alarm list. Or, no alarms in the alarm list.
0D
Alarm levels cannot be zero for alarms that are enabled.
0E
Too many slaves in the scanner’s input data table.
0F
The FMAX and Number of Lines do not yield correct vector calculations.
10
Phase (vector) alarms prohibited with synchronous sampling and more
than 1 tachometer pulse per revolution.
11
Order-base bands are prohibited on asynchronous channel.
12
Unsupported Sensor Type and Channel ID combination.
13
Invalid Alarm Type for the associated measurement ID.
14
Synchronous sampling is required for alarm on synchronous
measurements.
15
Integration is not supported with the Bypass High Pass Filter option.
The XM-320 module supports Poll, Change of State (COS), and Bit-Strobe
I/O messages. The Poll response message is used by the XM module to
produce measured values, and the COS message is used to produce the Alarm
and Relay Status. The Bit-Strobe message is used by a master device to send a
trigger event to all the XM slaves on the network.
Poll Message Format
The XM-320 Poll request message contains no data. The Poll response
message can contain up to 31 REAL values for a total of 124 bytes.
The XM-320 module provides one pre-defined (static) data format of the Poll
response, as defined in Assembly instance 101. It also provides a dynamic
Assembly instance, instance 199, with which you can define a custom data
format for the Poll response. The dynamic Assembly instance can contain any
of the measurement parameters included in Assembly instance 101, as well as
several of the alarm and relay configuration parameters.
The default Assembly instance is 101 and the default size is 8 bytes. You can
change the Assembly instance and define the custom Assembly instance using
the configuration software. Refer to I/O Data Parameters on page 65.
Publication GMSI10-UM005C-EN-P - May 2010
78
DeviceNet Information
The Poll response data can also be requested explicitly through Assembly
Object (Class ID 0x4), Instance 101 (0x65), Data Attribute (3).
The following table shows the static data format of Assembly instance 101.
XM-320 I/O Poll Response Message Format
Byte
Definition
0–3
Channel 1 Position measurement value
4–7
Channel 2 Position measurement value
COS Message Format
The XM-320 COS message contains five bytes of data as defined in the table
below. The COS data can also be requested explicitly through Assembly
Object (Class ID 0x4), Instance 100 (0x64), Data Attribute (3).
XM-320 COS Message Format
Byte
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
0
Relay 1
Status
Setpoint
Multiplier
Status
Alarm 2 Status
Alarm 1 Status
1
Relay 2
Status
Reserved
Reserved
Reserved
2
Relay 3
Status
Reserved
Reserved
Reserved
3
Relay 4
Status
Reserved
Reserved
Reserved
4
Relay 5
Status
Reserved
Reserved
Reserved
Bit 0
XM Status Values
The following tables describe the XM Status values that are included in the
COS messages.
Alarm Status Descriptions
Alarm Status Value
Publication GMSI10-UM005C-EN-P - May 2010
Description
0
Normal
1
Alert
2
Danger
3
Disarm
4
Transducer Fault (Sensor OOR)
DeviceNet Information
79
Alarm Status Descriptions
Alarm Status Value
Description
5
Module Fault
6
Tachometer Fault
7
Reserved
Setpoint Multiplier Status Descriptions
Setpoint Multiplier Status Value Description
0
Not Activated
1
Activated
Relay Status Descriptions
Relay Status Value
Description
0
Not Activated
1
Activated
Bit-Strobe Message Format
The Bit-Strobe command sends one bit of output data to each XM slave
whose node address appears in the master’s scanlist.
The Bit-Strobe command message contains a bit string of 64 bits (8 bytes) of
output data, one output bit per node address on the network. One bit is
assigned to each node address supported on the network (0...63) as shown in
Figure B.1.
Figure B.1 Bit-Strobe Command
Publication GMSI10-UM005C-EN-P - May 2010
80
DeviceNet Information
The XM modules use the bit received in a Bit-Strobe connection as a trigger
event. When the bit number corresponding to the XM module’s node address
is set, the XM module will collect the triggered trend data.
Note that the XM modules do not send data in the Bit-Strobe response.
ADR for XM Modules
Automatic Device Replacement (ADR) is a feature of an Allen-Bradley
DeviceNet scanner. It provides a means for replacing a failed device with a
new unit, and having the device configuration data set automatically. Upon
replacing a failed device with a new unit, the ADR scanner automatically
downloads the configuration data and sets the node address.
IMPORTANT
It is recommended that ADR not be used in safety related
applications. If the failure of the ADR server, and a subsequent power cycle, would result in the loss of protection for
a machine, then ADR should not be implemented.
ADR can be used with XM modules but keep the following in mind when
setting up the XM modules.
• The ADR scanner can not download the configuration data to an XM
module if the module has a saved configuration in its non-volatile
memory. This happens because the saved configuration is restored and
the module enters Run mode when the power is cycled. (Configuration
parameters cannot be downloaded while an XM module is in Run
mode.) XM modules must be in Program mode for the ADR
configuration to be downloaded and this occurs only when there is no
saved configuration.
TIP
To delete a saved configuration from non-volatile
memory, use the Delete service in RSNetWorx for
DeviceNet or perform the following steps in the XM
Serial Configuration Utility.
1. Save the current configuration to a file. From the
File menu, click Save As and enter a file name for
the configuration.
2. Reset the module to factory defaults. Click the
Module tab and click the Reset button.
3. Reload the saved configuration. From the File
menu, click Open and select the configuration file.
4. Make certain to disable auto save. From the Device
menu, clear the Auto Save Configuration check
mark.
Publication GMSI10-UM005C-EN-P - May 2010
DeviceNet Information
81
• An XM module will enter Run mode automatically after the ADR
scanner restores the module’s configuration only if the module is in Run
mode at the time the configuration is saved to the scanner. If the
module is in Program mode when the configuration is saved, then the
module will remain in Program after the configuration is downloaded by
the ADR scanner.
• The ADR scanner saves and restores only the configuration parameters
contained in the module’s EDS file. Some XM parameters are not
included in the EDS file because they are not supported by either the
EDS specification or the tools that read the EDS files, for example
RSNetWorx for DeviceNet. These configuration parameters will not be
restored with ADR.
Below is a list of the configuration parameters that are not included in
the EDS file and can not be saved or restored with ADR.
–
–
–
–
–
–
–
Channel Name
Tachometer Name
Alarm Name
Relay Name
All Triggered Trend related parameters (see page 63)
All SU/CD Trend related parameters
Custom Assembly structure (see page 65)
• The ADR and trigger group functions cannot be used together. A
module can have only one primary master so a module cannot be both
configured for ADR and included in a trigger group. The ADR scanner
must be the primary master for the modules configured for ADR. The
XM-440 Master Relay module must be the primary master for modules
included in a trigger group.
Publication GMSI10-UM005C-EN-P - May 2010
82
DeviceNet Information
Publication GMSI10-UM005C-EN-P - May 2010
Appendix
C
DeviceNet Objects
Appendix C provides information on the DeviceNet objects supported by the
XM-320 module.
For information about
Identity Object (Class ID 01H)
84
DeviceNet Object (Class ID 03H)
85
Assembly Object (Class ID 04H)
87
Connection Object (Class ID 05H)
90
Discrete Input Point Object (Class ID 08H)
92
Analog Input Point Object (Class ID 0AH)
93
Parameter Object (Class ID 0FH)
95
Acknowledge Handler Object (Class ID 2BH)
98
Alarm Object (Class ID 31DH)
99
Device Mode Object (Class ID 320H)
101
Relay Object (Class ID 323H)
102
Transducer Object (Class ID 328H)
105
4-20mA Output Object (Class ID 32AH)
106
TIP
83
See page
Refer to the DeviceNet specification for more information
about DeviceNet objects. Information about the
DeviceNet specification is available on the ODVA web site
(http://www.odva.org).
Publication GMSI10-UM005C-EN-P - May 2010
84
DeviceNet Objects
The Identity Object provides identification and general information about the
device.
Identity Object
(Class ID 01H)
Class Attributes
The Identity Object provides no class attributes.
Instance Attributes
Table C.1 Identity Object Instance Attributes
Attr ID
Access
Rule
Name
Data Type
Default Value
1
Get
Vendor ID
UINT
668 = Entek
2
Get
Device Type
UINT
109 (Specialty I/O)
3
Get
Product Code
UINT
23 (0x17) XM-320
4
Get
Revision:
Major
Minor
STRUCT OF
USINT
USINT
Value varies with each firmware revision.
Value varies with each firmware revision.
5
Get
Status
WORD
6
Get
Serial Number
UDINT
7
Get
Product Name
SHORT_
STRING
"XM-320 Position Module"
Status
The Status is a 16 bit value. The following bits are implemented.
Table C.2 Identity Object Status
Bit
Name
Description
0
Owned
TRUE indicates that the module has an owner. More
specifically, the Predefined Master/Slave Connection Set
has been allocated to a master.
1
2
3
Publication GMSI10-UM005C-EN-P - May 2010
Reserved, set to 0
Configured
This bit is set whenever a saved configuration is
successfully loaded from non-volatile memory. This bit is
cleared whenever the default configuration is restored or
loaded.
Reserved, set to 0
DeviceNet Objects
85
Table C.2 Identity Object Status
Bit
Name
Description
4
Boot Program
Vendor-specific, indicates that the boot program is
running. The Main Application must be corrupt or
missing.
5-7
Vendor-specific, not implemented
8
Minor Recoverable
Fault
9
Minor Unrecoverable Not implemented
Fault
10
Major Recoverable
Fault
11
Major Unrecoverable Set when there is a module status fault (Module Status
Fault
LED is solid red).
12 - 15
Set whenever there is a transducer or tachometer fault.
Set when the module detects a major problem that the
user may be able to recover from. The Module Status
LED will flash red. An example of this condition is when
the boot program is running.
Reserved, set to 0
Services
Table C.3 Identity Object Services
1
DeviceNet Object
(Class ID 03H)
Service
Code
Class/Instance Usage
Name
01h
Instance
Get_Attributes_All
05h
Instance
Reset
0Eh
Instance
Get_Attribute_Single
10h
Instance
Set_Attribute_Single1
Attributes can only be set while the device is in Program Mode. See the description of the Device Mode Object
for more information.
The DeviceNet Object is used to provide the configuration and status of a
physical attachment to DeviceNet.
Publication GMSI10-UM005C-EN-P - May 2010
86
DeviceNet Objects
Class Attributes
Table C.4 DeviceNet Object Class Attributes
Attr ID
Access
Rule
Name
Data Type
Default Value
1
Get
Revision
UINT
2
Instance Attributes
Table C.5 DeviceNet Object Instance Attributes
Attr ID
Access
Rule
Name
Data Type
Default Value
1
Get/Set
MAC ID1
USINT
63
2
Get/Set
Baud Rate2
USINT
0
3
Get
Bus-Off Interrupt
BOOL
0
4
Get/Set
Bus-Off Counter
USINT
0
5
Get
Allocation Information
STRUCT of
BYTE
USINT
0 255
100
Get/Set
Autobaud Disable
BOOL
0 (Ignore attribute 2 and always autobaud)
1
Setting the MAC ID causes the device to reset automatically, after which it will go online with the new MAC
ID.
2
The Baud Rate setting can not be set while Autobaud Disable is equal to 0. The new baud rate will not take
effect until the module is reset.
The MAC ID, Baud Rate, and Autobaud Disable settings are stored in
non-volatile memory so they do not reset to the default with each power cycle.
The Baud Rate attribute supports the following settings:
• 0 = 125 kbps
• 1 = 250 kbps
• 2 = 500 kbps
The Baud Rate setting is used only when automatic baud rate detection is
disabled (Autobaud Disable = 1). When Autobaud Disable is set to zero
(0), the module ignores its Baud Rate setting and performs automatic baud
rate detection instead. This means that the module will determine the network
baud rate by listening for network traffic before attempting to go online.
Publication GMSI10-UM005C-EN-P - May 2010
DeviceNet Objects
87
Services
Table C.6 DeviceNet Object Services
Service
Code
Class/Instance Usage
Name
0Eh
Class/Instance
Get_Attribute_Single
10h
Instance
Set_Attribute_Single1
4Bh
Instance
Allocate_Master/Slave_Connetion_Set
4Ch
Instance
Release_Group_2_Identifier_Set
1
Attributes can only be set while the device is in Program Mode. See the description of the Device Mode Object
for more information.
The Assembly Object binds attributes of multiple objects to allow data to or
from each object to be sent or received in a single message.
Assembly Object
(Class ID 04H)
The XM-320 module provides both static and dynamic assemblies.
Class Attributes
Table C.7 Assembly Object Class Attributes
Attr ID
Access
Rule
Name
Data Type
Description
Semantics
1
Get
Revision
UINT
Revision of the
implemented object.
2
Instances
Table C.8 Assembly Object Instances
Instance
Name
Type
Description
100
Default COS Message
Input
Alarm and Relay Status values
101
Default Poll Response
Message
Input
Measurement values
102 - 106
Alternate Poll Response
Message
Input
Measurement values
199
Alternate Dynamic Poll
Response Message
Input
User configurable
measurement values and
configuration parameters
Publication GMSI10-UM005C-EN-P - May 2010
88
DeviceNet Objects
Instance Attributes
Table C.9 Assembly Object Instance Attributes
Attr ID
Access
Rule
Name
Data Type
Value
1
Get
Number of Members in list
UINT
Only supported for Dynamic Assembly
instance
2
Set
Member List
Array of STRUCT:
Only supported for Dynamic Assembly
instance
Member Data Description
3
Get
UINT Size of member data value in bits
Member Path Size
UINT
Member Path
Packed EPATH
Data
Defined in tables
on the following
pages.
Assembly Instance Attribute Data Format
Instance 100 - Alarm and Relay Status
This assembly is sent using COS messaging when any of the Alarm or Relay
Status values change.
Table C.10 Instance 100 Data Format (Alarm and Relay Status Values Assembly)
Byte
Bit 7
Bit 6
0
Relay 1
Status
Set Point
Multiplier
1
Relay 2
Status
2
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Alarm 2 Status
Alarm 1 Status
0
0
0
Relay 3
Status
0
0
0
3
Relay 4
Status
0
0
0
4
Relay 5
Status
0
0
0
Publication GMSI10-UM005C-EN-P - May 2010
DeviceNet Objects
89
Instance 101 - Measurement Values
This is the default assembly instance that is sent using the I/O Poll Response
message when an I/O Poll Request is received from a DeviceNet Master.
Table C.11 Instance 101 Data Format (Measurement Values Assembly)
Byte
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
0-3
Transducer 1 Position value
4-7
Transducer 2 Position value
Bit 1
Bit 0
Instance 199 - Dynamic Assembly
This Assembly instance can be created and configured with the XM Serial
Configuration Utility or RSMACC Enterprise Online Configuration Utility.
Using the configuration software, you determine the format of the data. This
assembly instance can be selected to be sent in response to an I/O Poll request
from a Master.
The dynamic Assembly can include all of the measurement values included in
Assembly instance 101. In addition, the dynamic Assembly can include the
following configuration parameters.
Table C.12 Instance 199 Component Mapping
EPATH (where ii =
instance number)
Class
Name
Class
Number
Instance
Number
Attribute
Name
Attribute
Number
Data
Type
21 1D 03 24 ii 30 04
Alarm
31Dh
1-2
Alarm Enable
4
BOOL
21 1D 03 24 ii 30 07
Alarm
31Dh
1-2
Condition
7
USINT
21 1D 03 24 ii 30 08
Alarm
31Dh
1-2
Alert Threshold (High)
8
REAL
21 1D 03 24 ii 30 09
Alarm
31Dh
1-2
Danger Threshold
(High)
9
REAL
21 1D 03 24 ii 30 0A
Alarm
31Dh
1-2
Alert Threshold Low
10
REAL
21 1D 03 24 ii 30 0B
Alarm
31Dh
1-2
Danger Threshold Low 11
REAL
21 1D 03 24 ii 30 0C
Alarm
31Dh
1-2
Hysteresis
12
REAL
21 1D 03 24 ii 30 0D
Alarm
31Dh
1-2
Threshold (Set Point)
Multiplier
13
REAL
21 1D 03 24 ii 30 0E
Alarm
31Dh
1 - 16
Startup Period
14
UINT
21 23 03 24 ii 30 04
Relay
323h
1-5
Relay Enable
4
BOOL
21 23 03 24 ii 30 05
Relay
323h
1-5
Latch Enable
5
BOOL
21 23 03 24 ii 30 06
Relay
323h
1-5
Failsafe Enable
6
BOOL
21 23 03 24 ii 30 07
Relay
323h
1-5
Delay
7
UINT
21 23 03 24 ii 30 09
Relay
323h
1-5
Alarm Level
9
BYTE
Publication GMSI10-UM005C-EN-P - May 2010
90
DeviceNet Objects
Table C.12 Instance 199 Component Mapping
EPATH (where ii =
instance number)
Class
Name
Class
Number
Instance
Number
Attribute
Name
Attribute
Number
Data
Type
21 0F 00 24 ii 30 01
Param
0Fh
6 - 10
Parameter Value
(Alarm Identifier A)
1
USINT
21 0F 00 24 ii 30 01
Param
0Fh
11 - 15
Parameter Value
(Alarm Identifier B)
1
USINT
21 23 03 24 ii 30 0C
Relay
323h
1-5
Logic
12
USINT
21 23 03 24 ii 30 0E
Relay
323h
1-5
Relay Installed
14
BOOL
The dynamic Assembly instance must be instantiated with a call to the class
level Create service. Then the structure can be defined with the
Set_Attribute_Single service for the Member List attribute. Only one dynamic
Attribute instance is supported so subsequent calls to the Create service will
return a Resource Unavailable (0x02) error. The Delete service can be used to
destroy the dynamic Assembly instance so that it can be re-created.
Services
Table C.13 Assembly Object Services
Connection Object
(Class ID 05H)
Service
Code
Class/Instance Usage
Name
0Eh
Class/Instance
Get_Attribute_Single
10h
Instance
Set_Attribute_Single
08h
Class
Create
09h
Instance
Delete
The Connection Object allocates and manages the internal resources
associated with both I/O and Explicit Messaging Connections.
Class Attributes
The Connection Object provides no class attributes.
Publication GMSI10-UM005C-EN-P - May 2010
DeviceNet Objects
91
Instances
Table C.14 Connection Object Instances
Instance
Description
1
Explicit Message Connection for pre-defined connection set
2
I/O Poll Connection
3
I/O Strobe Connection
4
I/O COS (change of state) Connection
11 - 17
Explicit Message Connection
Instance Attributes
Table C.15 Connection Object Instance Attributes
Attr ID
Access
Rule
Name
Data Type
Description
1
Get
State
USINT
State of the object.
2
Get
Instance Type
USINT
Indicates either I/O or Messaging
Connection.
3
Get
Transport Class Trigger
BYTE
Defines behavior of the Connection.
4
Get
Produced Connection ID
UINT
Placed in CAN Identifier Field when the
Connection transmits.
5
Get
Consumed Connection
ID
UINT
CAN Identifier Field value that denotes
message to be received.
6
Get
Initial Comm
Characteristics
BYTE
Defines the Message Group(s) across
which productions and consumptions
associated with this Connection occur.
7
Get
Produced Connection
Size
UINT
Maximum number of bytes transmitted
across this Connection.
8
Get
Consumed Connection
Size
UINT
Maximum number of bytes received across
this Connection.
9
Get/Set
Expected Packet Rate
UINT
Defines timing associated with this
Connection.
12
Get/Set
Watchdog Time-out
Action
USINT
Defines how to handle Inactivity/Watchdog
timeouts.
13
Get
Produced Connection
Path Length
UINT
Number of bytes in the
production_connection_path attribute.
14
Get
Produced Connection
Path
Array of
USINT
Specifies the Application Object(s) whose
data is to be produced by this Connection
Object. See DeviceNet Specification
Volume 1 Appendix I.
Publication GMSI10-UM005C-EN-P - May 2010
92
DeviceNet Objects
Table C.15 Connection Object Instance Attributes
Attr ID
Access
Rule
15
Name
Data Type
Description
Get
Consumed Connection
Path Length
UINT
Number of bytes in the
consumed_connection_path attribute.
16
Get
Consumed Connection
Path
Array of
USINT
Specifies the Application Object(s) that are
to receive the data consumed by this
Connection Object. See DeviceNet
Specification Volume 1 Appendix I.
17
Get
Production Inhibit Time
UINT
Defines minimum time between new data
production.
Services
Table C.16 Connection Object Services
Discrete Input Point Object
(Class ID 08H)
Service
Code
Class/Instance Usage
Name
05h
Instance
Reset
0Eh
Instance
Get_Attribute_Single
10h
Instance
Set_Attribute_Single
The Discrete Input Point Object stores information about the value of the
Setpoint Multiplier signal.
Class Attributes
Table C.17 Discrete Input Object Class Attributes
Attr ID
Access
Rule
Name
Data Type
Description
Semantics
1
Get
Revision
UINT
Revision of the
implemented object.
2
Publication GMSI10-UM005C-EN-P - May 2010
DeviceNet Objects
93
Instance Attributes
Table C.18 Discrete Input Object Instance Attributes
Attr ID
Access
Rule
Name
Data Type
Description
Semantics
3
Get
Value
BOOL
Setpoint Multiplier
0 = Off
1 = On
199
Set
Backdoor
Service
USINT
Setting this attribute is
equivalent to requesting
the specified service.
Set to one of the
following values to
perform the
specified service:
0x32 = Open
0x33 = Close
Services
Table C.19 Discrete Input Object Services
Service
Code
Class/Instance Usage
Name
Description
0Eh
Class/Instance
Get_Attribute_Single
Returns the contents of the
specified attribute.
10h
Instance
Set_Attribute_Single
Sets the contents of the
specified attribute.
32h
Instance
Open
Opens the virtual Setpoint
Multiplier switch.
33h
Instance
Close
Closes the virtual Setpoint
Multiplier switch.
Analog Input Point Object
(Class ID 0AH)
The Analog Input Point Object models simple analog measurements
performed by the XM-320 module.
Class Attributes
Table C.20 Analog Input Point Object Class Attributes
Attr ID
Access
Rule
Name
Data Type
Description
Semantics
1
Get
Revision
UINT
Revision of the
implemented object.
2
Publication GMSI10-UM005C-EN-P - May 2010
94
DeviceNet Objects
Instances
Table C.21 Analog Input Point Object Instances
Instance
Name
Description
1
Position
Position measurement for transducer 1.
2
Position
Position measurement for transducer 2.
Instance Attributes
Table C.22 Analog Input Point Object Class Attributes
Attr ID
Access
Rule
Name
Data Type
Description
Semantics
3
Get
Value
REAL
The position
measurement value.
The raw measured value plus
any offset specified by
Calibration Bias.
4
Get
Status
BOOL
Indicates if a fault or
alarm has occurred.
0 = Operating without alarms or
faults
1 = Alarm or fault condition
exists. The Value attribute may
not represent the actual field
value.
8
Get
Value Data Type USINT
Determines the data type
of the Value.
1 = REAL
122
Get/Set
Calibration Bias REAL
Offset added into the raw
measured value.
Used to set the "zero point."
147
Get/Set
Data Units
The units context of the
Value attribute.
See DeviceNet Specification
Volume 1 Appendix.
ENGUNIT
Services
Table C.23 Analog Input Point Object Services
Service
Code
Class/Instance Usage
Name
Description
0Eh
Class/Instance
Get_Attribute_Single
Returns the contents of the
specified attribute.
10h
Instance
Set_Attribute_Single
Sets the contents of the
specified attribute.1
1
Publication GMSI10-UM005C-EN-P - May 2010
Attributes can only be set while the device is in Program Mode. See the description of the Device Mode Object
for more information.
DeviceNet Objects
Parameter Object
(Class ID 0FH)
95
The Parameter Object provides the interface to the XM-320 configuration
data. There are 15 Parameter Object instances implemented in the XM-320
module.
Parameter Object instances 1-4 and 6-15 are implemented to provide an
alternate method of setting the configuration parameters with EPATH or
ENGUNIT data types.
Instance 5 of the Parameter Object is for setting the device "Mode." The
Mode setting determines how the two position sensors are used:
• Normal - The two sensors are used independently to perform two
separate position measurements.
• Head-to-Head - The two sensors are used together, facing each other
on either side of the target, to perform a single position measurement.
This mode can be used to extend upon the range of a single sensor.
• Radial Cancel - The two sensors are used together to perform a single
position measurement. The second sensor is setup in such a way that it
can measure the radial movement of the target. The radial movement
can then be subtracted out of the position measurement performed by
the first sensor.
Class Attributes
Table C.24 Parameter Object Class Attributes
Attr ID
Access
Rule
Name
Data Type
Description
Semantics
2
Get
Max Instance
UINT
Maximum instance
number of an object in
this class.
Total number of parameter
object instances.
8
Get
Parameter Class WORD
Descriptor
Bits that describe the
parameter.
Bit 0 Supports Parameter
Instances
Bit 1 Supports Full Attrib.
Bit 2 Must do non-volatile store
Bit 3 Params in non-volatile
9
Get
Config.
Assembly
Instance
UINT
Set to 0
Publication GMSI10-UM005C-EN-P - May 2010
96
DeviceNet Objects
Instances
There are 15 instances of this object.
Table C.25 Parameter Object Instances
Instance
Read
Only
Name
Data Type
Valid Values
Default Value
1
No
Transducer 1 Sensitivity Units
USINT
0 = mils
1 = degrees of rotation
2 = mm
3 = percent
0
2
No
Transducer 2 Sensitivity Units
USINT
0 = mils
1 = degrees of rotation
2 = mm
3 = percent
0
3
No
Position Measurement 1 Units USINT
0 = mils
1 = degrees of rotation
2 = mm
3 = percent
0
4
No
Position Measurement 2 Units USINT
0 = mils
1 = degrees of rotation
2 = mm
3 = percent
0
5
No
Mode
USINT
0 = Normal
1 = Head-to-Head
2 = Radial Cancel
0
6
No
Relay 1 Alarm Identifier A
USINT
0 = Alarm 1
1 = Alarm 2
0
7
No
Relay 2 Alarm Identifier A
USINT
0 = Alarm 1
1 = Alarm 2
0
8
No
Relay 3 Alarm Identifier A
USINT
0 = Alarm 1
1 = Alarm 2
0
9
No
Relay 4 Alarm Identifier A
USINT
0 = Alarm 1
1 = Alarm 2
0
10
No
Relay 5 Alarm Identifier A
USINT
0 = Alarm 1
1 = Alarm 2
0
11
No
Relay 1 Alarm Identifier B
USINT
0 = Alarm 1
1 = Alarm 2
0
12
No
Relay 2 Alarm Identifier B
USINT
0 = Alarm 1
1 = Alarm 2
0
13
No
Relay 3 Alarm Identifier B
USINT
0 = Alarm 1
1 = Alarm 2
0
14
No
Relay 4 Alarm Identifier B
USINT
0 = Alarm 1
1 = Alarm 2
0
15
No
Relay 5 Alarm Identifier B
USINT
0 = Alarm 1
1 = Alarm 2
0
Publication GMSI10-UM005C-EN-P - May 2010
DeviceNet Objects
97
Table C.25 Parameter Object Instances
Instance
Read
Only
16
17
Name
Data Type
Valid Values
Default Value
No
Poll Connection Produced
Connection Path
USINT
101, 199 (Assembly Object
instance number)
101
No
Poll Connection Produced
Connection Size
UINT
4 - 124
8
Instance Attributes
Table C.26 Parameter Object Instance Attributes
Attr ID
Access
Rule
1
Set
Parameter
Value
2
Get
Link Path Size
USINT
Size of Link Path
3
Get
Link Path
ARRAY of
DeviceNet
path
DeviceNet path to the
object for the Parameter
value.
Segment
Type/Port
BYTE
See DeviceNet
Specification Volume 1
Appendix I for format.
Name
Data Type
Description
Semantics
Actual value of parameter See Table C.25 for a list of valid
values for each instance.
Segment
Address
0 (These Parameter instances do
not link directly to another
object attribute.)
See DeviceNet
Specification Volume 1
Appendix I for format.
4
Get
Descriptor
WORD
Description of Parameter
Bit 0 = Settable Path support
Bit 1 = Enum Strings support
Bit 2 = Scaling support
Bit 3 = Scaling Links support
Bit 4 = Read Only
Bit 5 = Monitor
Bit 6 = Ext. Prec. scaling
5
Get
Data Type
EPATH
Data Type Code
See DeviceNet Specification
Volume 1 Appendix J, Section
J-6.
6
Get
Data Size
USINT
Number of Bytes in
Parameter value.
Publication GMSI10-UM005C-EN-P - May 2010
98
DeviceNet Objects
Services
Table C.27 Parameter Object Services
Service
Code
Class/Instance Usage
Name
Description
0Eh
Class/Instance
Get_Attribute_Single
Returns the contents of the
specified attribute.
10h
Class
Set_Attribute_Single
Sets the contents of the
specified attribute.1
1
Attributes can only be set while the device is in Program Mode. See the description of the Device Mode Object
for more information.
The Acknowledge Handler Object is used to manage the reception of message
acknowledgments. This object communicates with a message producing
Application Object within a device. The Acknowledge Handler Object notifies
the producing application of acknowledge reception, acknowledge timeouts,
and production retry limit errors.
Acknowledge Handler
Object
(Class ID 2BH)
Class Attributes
The Acknowledge Handler Object provides no class attributes.
Instances
A module provides only a single instance (instance 1) of the Acknowledge
Handler Object. This instance is associated with instance 4 of the Connection
Object, the slave COS connection to a higher level master.
Instance Attributes
Table C.28 Acknowledge Handler Object Instance Attributes
Attr ID
Access
Rule
Name
Data Type
Default Value
1
Get/Set
Acknowledge Timer
UINT
16ms
2
Get/Set
Retry Limit
USINT
1
3
Get
COS Producing
Connection Instance
UINT
4
Publication GMSI10-UM005C-EN-P - May 2010
DeviceNet Objects
99
Services
Table C.29 Acknowledge Handler Object Services
Service
Code
Class/Instance Usage
Name
0Eh
Instance
Get_Attribute_Single
10h
Instance
Set_Attribute_Single
The Alarm Object models a two-stage (alert and danger levels) alarm.
Alarm Object
(Class ID 31DH)
Class Attributes
Table C.30 Alarm Object Class Attributes
Attr ID
Access
Rule
Name
Data Type
Description
Semantics
1
Get
Revision
USINT
Revision of the
implemented object.
2 (indicates that Threshold
Multiplier is a REAL instead of
USINT)
Instances
There are 2 instances of this object.
Instance Attributes
Table C.31 Alarm Object Instance Attributes
Attr ID
Access
Rule
Name
Data Type
Description
Semantics
3
Get
Alarm Status
3 BITS
The current status of the
alarm.
0 = Normal
1 = Alert (alarm)
2 = Danger (shutdown)
3 = Disarm
4 = Xdcr Fault
5 = Module Fault
4
Get/Set
Alarm Enable
BOOL
Indicates whether this
alarm object is enabled.
0 = Disabled
1 = Enabled
Publication GMSI10-UM005C-EN-P - May 2010
100
DeviceNet Objects
Table C.31 Alarm Object Instance Attributes
Attr ID
Access
Rule
Name
Data Type
Description
Semantics
6
Get
Threshold Units
USINT
Indicates whether the
threshold and hysteresis
value are specified in
units of measure.
Set to 1
1 = Measurement units
7
Get/Set
Condition
USINT
Indicates on which side of
the threshold values the
alarm and danger
conditions exist.
0 = Greater than
1 = Less than
2 = Inside range
3 = Outside range
8
Get/Set
Alert Threshold
(High)
REAL
The threshold value for
the alert (alarm) condition
(greater threshold for
range types).
9
Get/Set
Danger Threshold
(High)
REAL
The threshold value for
the danger (shutdown)
condition (greater
threshold for range types).
10
Get/Set
Alert Threshold
Low
REAL
The lesser threshold value
for the alert (alarm)
condition for the range
condition types.
11
Get/Set
Danger Threshold
Low
REAL
The lesser threshold value
for the danger (shutdown)
condition for the range
condition types.
12
Get/Set
Hysteresis
REAL
The amount on the safe
side of a threshold by
which the value must
recover to clear the alarm.
13
Get/Set
Threshold (Setpoint REAL
Multiplier)
Indicates how the
thresholds should be
adjusted when the
setpoint multiplication
function is invoked.
0 = Disable alarm
> 0 = Multiply the thresholds by
the value
14
Get/Set
Startup Period
UINT
The amount of time that
the Threshold (Setpoint)
Multiplier is applied after
the startup signal is
received.
Seconds
18
Get/Set
Name
STRING2
A name to help identify
this alarm.
Publication GMSI10-UM005C-EN-P - May 2010
DeviceNet Objects
101
Services
Table C.32 Alarm Object Services
Service
Code
Class/Instance Usage
Name
Description
0Eh
Instance
Get_Attribute_Single
Returns a single attribute.
10h
Instance
Set_Attribute_Single
Sets a single attribute.1
1
Device Mode Object
(Class ID 320H)
Attributes can only be set while the device is in Program Mode. See the description of the Device Mode Object
for more information.
The Device Mode Object is used to control access to the configuration
parameters in the module. This object’s Device Mode attribute must be in
PROGRAM mode to allow the module’s configuration parameters to be "Set"
(see Services). Attempts to set the configuration parameters while the Device
Mode is in RUN mode will return an error. Note that the module collects
measurements while in RUN mode but not while it is in PROGRAM mode.
Class Attributes
The Device Mode Object provides no class attributes.
Instance Attributes
Table C.33 Device Mode Object Instance Attributes
Attr ID
Access
Rule
Name
Data Type
Description
3
Get/Set
Device Mode
UINT
The operating mode of the 0 = Power Up
module.
1 = RUN
2 = PROGRAM
199
Set
Backdoor
Service
USINT
Setting this attribute is
equivalent to requesting
the specified service.
Semantics
Set to one of the following
values to perform the specified
service:
0x05 = Reset
0x09 = Delete
0x15 = Restore
0x16 = Save
Setting the Device Mode attribute to "1" (RUN) is equivalent to executing the
Start service. Setting the Device Mode attribute to "2" (PROGRAM) is
equivalent to executing the Stop service.
Publication GMSI10-UM005C-EN-P - May 2010
102
DeviceNet Objects
Services
Table C.34 Device Mode Object Services
Service
Code
Class/Instance Usage
Name
Description
0Eh
Instance
Get_Attribute_Single
Return the value of a single
attribute.
10h
Instance
Set_Attribute_Single
Set the value of a single
attribute.
07h
Instance
Stop
Transitions from Run to the
Program state.
06h
Instance
Start
Validate the device
configuration settings and
transition to the Run state if
OK.
05h
Instance
Reset
Transition to the Power Up
state. Load the non-volatile
configuration and transition
to the Run state if saved
configuration restored.
16h
Instance
Save
Validate the device
configuration settings if
necessary and save them to
non-volatile memory.
09h
Instance
Delete
Delete the saved
configuration from
non-volatile memory.
15h
Instance
Restore
Load the saved
configuration or the factory
default configuration from
non-volatile memory.
Relay Object
(Class ID 323H)
Publication GMSI10-UM005C-EN-P - May 2010
The Relay Object models a relay (actual or virtual). A relay can be activated or
deactivated based on the status of one or more alarms.
DeviceNet Objects
103
Class Attributes
Table C.35 Relay Object Class Attributes
Attr ID
Access
Rule
3
100
Name
Data Type
Description
Semantics
Get
Number of
Instances
UINT
Number of Instances in
this class.
5
Set
Reset All
USINT
Setting this attribute is
equivalent to executing
the Class Reset service
Reset All is an attribute that
provides a way to perform a
Class level Reset service via the
Set_Attribute_Single service.
Setting this attribute to any
value is equivalent to
performing the Class level Reset
service. Reading the Reset All
attribute always returns zero.
Instances
There are 5 instances of this object.
Instance Attributes
Table C.36 Relay Object Instance Attributes
Attr ID
Access
Rule
Name
Data Type
Description
Semantics
3
Get
Relay Status
BOOL
The current status of the
relay.
0 = Off
1 = On
4
Get/Set
Relay Enable
BOOL
Indicates whether this
relay object is enabled.
0 = Disabled
1 = Enabled
5
Get/Set
Latch Enable
BOOL
Indicates whether this
relay latches (requires a
reset command to
deactivate).
0 = Nonlatching
1 = Latching
6
Get/Set
Failsafe Enable
BOOL
Indicates whether this
relay is normally
energized (activated
during power loss).
0 = Non-failsafe (not normally
energized)
1 = Failsafe (normally energized)
7
Get/Set
Delay
USINT
The time period that the
voting logic must be true
before the relay is
activated.
0 to 25.5 seconds
(specified in tenths of seconds)
8
Get/Set
Name
STRING2
A name to help identify
the relay.
18 characters maximum
Publication GMSI10-UM005C-EN-P - May 2010
104
DeviceNet Objects
Table C.36 Relay Object Instance Attributes
Attr ID
Access
Rule
Name
Data Type
Description
Semantics
9
Get/Set
Alarm Level
BYTE
Specifies what alarm
status values will cause
the relay to activate.
0 = Normal
1 = Alert
2 = Danger
3 = Disarm
4 = Xdcr Fault
5 = Module Fault
10
Get/Set
Alarm Identifier
A
EPATH
Identifies the first alarm
status the relay monitors.
See Parameter Object instances
6 to 10.
11
Get/Set
Alarm Identifier
B
EPATH
Identifies the second
alarm status the relay
monitors.
See Parameter Object instances
11 to 15.
12
Get/Set
Logic
USINT
Indicates the number of
associated alarms that
must have a status value
specified by Alarm Level
in order to activate the
relay.
0 = Ignore Alarm Identifier B
and activate the relay based on
the status of Alarm Identifier
A.
1 = Activate the relay if the
status of either Alarm
Identifier A or B matches any
of the statuses specified by
Alarm Level.
2 = Activate the relay if the
status of both Alarm Identifier
A and B match any of the
statuses specified by Alarm
Level.
14
Get
Relay Installed
BOOL
Indicates whether an
actual relay is associated
with this instance.
0 = Not installed
1 = Installed
Services
Table C.37 Relay Object Services
Service
Code
Class/Instance Usage
Name
Description
05h
Class/Instance
Reset
Resets latched relay.
0Eh
Class/Instance
Get_Attribute_Single
Returns a single attribute.
10h
Class/Instance
Set_Attribute_Single
Sets a single attribute.1
1
Publication GMSI10-UM005C-EN-P - May 2010
Attributes can only be set while the device is in Program Mode. See the description of the Device Mode Object
for more information.
DeviceNet Objects
Transducer Object
(Class ID 328H)
105
The Transducer Object models a transducer.
Class Attributes
The Transducer Object provides no class attributes.
Instances
There are 2 instances of this object.
Instance Attributes
Table C.38 Transducer Object Instance Attributes
Attr ID
Access
Rule
Name
Data Type
Description
3
Get
DC Bias
REAL
The measured average DC Volts
bias of the transducer
signal in volts.
4
Get
Status
BOOL
0 = No fault
Indicates whether a
1 = A transducer fault exists
transducer fault exists
(the measured DC Bias is
outside the range
specified by Fault High
and Low).
5
Get/Set
Sensitivity
Value
REAL
Value of the sensitivity of
the transducer in
millivolts per Sensitivity
Units.
6
Get/Set
Sensitivity Units ENGUNIT
Semantics
Units of the denominator See DeviceNet Specification
of the Sensitivity Value. Volume 1 Appendix K. Also see
Parameter Object instances 1
and 2.
Valid values:
mils = 0800 hex
degrees of rotation = 1703 hex
mm = 2203 hex
7
Get/Set
Fault High
REAL
The maximum expected
DC Bias voltage from the
transducer in volts.
Volts
8
Get/Set
Fault Low
REAL
The minimum expected
DC Bias voltage from the
transducer in volts.
Volts
Publication GMSI10-UM005C-EN-P - May 2010
106
DeviceNet Objects
Table C.38 Transducer Object Instance Attributes
Attr ID
Access
Rule
Name
Data Type
Description
Semantics
11
Get/Set
Target Angle
REAL
The angle of the target
relative to the shaft in
degrees.
0 to 90 degrees
12
Get/Set
Upscale
BOOL
Indicates the movement
of the target relative to
the transducer which is
considered positive
displacement.
0 = Away
1 = Towards
13
Get/Set
DC Bias Time
Constant
REAL
The time constant value
used for exponential
averaging of the DC Bias
value (a low pass
filter/output smoothing
filter).
Seconds
14
Get/Set
Name
STRING2
A name to help identify
this transducer or
channel.
18 characters maximum
Services
Table C.39 Transducer Object Services
Service
Code
Class/Instance Usage
Name
Description
0Eh
Instance
Get_Attribute_Single
Returns a single attribute.
10h
Instance
Set_Attribute_Single
Sets a single attribute.1
1
4-20mA Output Object
(Class ID 32AH)
Attributes can only be set while the device is in Program Mode. See the description of the Device Mode Object
for more information.
The 4-20mA Output Object models the configuration of a 4-20mA output
signal.
Class Attributes
The 4-20mA Output Object provides no class attributes.
Publication GMSI10-UM005C-EN-P - May 2010
DeviceNet Objects
107
Instances
There are 2 instances of this object.
Instance Attributes
Table C.40 4-20mA Output Object Instance Attributes
Attr ID
Access
Rule
Name
Data Type
Description
Semantics
3
Get/Set
Value
REAL
The current output value.
mA
4
Get/Set
Enable
BOOL
Indicates whether this
4-20mA output is
enabled.
0 = Disabled
1 = Enabled
5
Get/Set
Max Range
REAL
The measured value
associated with 20mA.
6
Get/Set
Min Range
REAL
The measured value
associated with 4mA.
Services
Table C.41 4-20mA Output Object Services
Service
Code
Class/Instance Usage
Name
Description
0Eh
Instance
Get_Attribute_Single
Returns a single attribute.
10h
Instance
Set_Attribute_Single
Sets a single attribute.1
1
Attributes can only be set while the device is in Program Mode. See the description of the Device Mode Object
for more information.
Publication GMSI10-UM005C-EN-P - May 2010
108
DeviceNet Objects
Publication GMSI10-UM005C-EN-P - May 2010
Glossary
alarm
An alarm alerts you to a change in a measurement. For example, an alarm can
notify you when the measured vibration level for a machine exceeds a
pre-defined value.
Automatic Device Replacement (ADR)
A means for replacing a malfunctioning device with a new unit, and having the
device configuration data set automatically. The ADR scanner uploads and
stores a device’s configuration. Upon replacing a malfunctioning device with a
new unit (MAC ID 63), the ADR scanner automatically downloads the
configuration data and sets the MAC ID (node address).
baud rate
The baud rate is the speed at which data is transferred on the DeviceNet
network. The available data rates depend on the type of cable and total cable
length used on the network:
Maximum Cable Length
Cable
125K
250K
500K
Thick Trunk Line
500m (1,640ft.)
250m (820ft.)
100m (328ft.)
Thin Trunk Line
100m (328ft.)
100m (328ft.)
100m (328ft.)
Maximum Drop Length
6m (20ft.)
6m (20ft.)
6m (20ft.)
Cumulative Drop Length
156m (512ft.)
78m (256ft.)
39m (128ft.)
The XM measurement modules’ baud rate is automatically set by the bus
master. You must set the XM-440 Relay module baud rate. You set the
XM-440 Relay Master to 125kb, 250kb, 500kb, or Autobaud if another device
on the network has set the baud rate.
Bit-Strobe
A multicast transfer of data sent by a master device to all the XM slaves on the
network. The bit-strobe command message contains a bit string of 64 bits (8
bytes) of output data, one output bit per node address on the network.
bus off
A bus off condition occurs when an abnormal rate of errors is detected on the
Control Area Network (CAN) bus in a device. The bus-off device cannot
receive or transmit messages on the network. This condition is often caused by
corruption of the network data signals due to noise or baud rate mismatch.
109
Publication GMSI10-UM005C-EN-P - May 2010
Glossary
110
Change of State (COS)
DeviceNet communications method in which the XM module sends data
based on detection of any changed value within the input data (alarm or relay
status).
current configuration
The current configuration is the most recently loaded set of configuration
parameters in the XM module’s memory. When power is cycled, the current
configuration is loaded with either the saved configuration (in EEPROM) or
the factory defaults (if there is no saved configuration). In addition, the current
configuration contains any configuration changes that have been downloaded
to the module since power was applied.
DeviceNet network
A DeviceNet network uses a producer/consumer Controller Area Network
(CAN) to connect devices (for example, XM modules). A DeviceNet network
can support a maximum of 64 devices. Each device is assigned a unique node
address (MAC ID) and transmits data on the network at the same baud rate.
A cable is used to connect devices on the network. It contains both the signal
and power wires. General information about DeviceNet and the DeviceNet
specification are maintained by the Open DeviceNet Vendor’s Association
(ODVA). ODVA is online at http://www.odva.org.
disarm state
See Program mode.
EEPROM
See NVS (Non-Volatile Storage).
Electronic Data Sheet (EDS) Files
EDS files are simple text files that are used by network configuration tools
such as RSNetWorx for DeviceNet to describe products so that you can easily
commission them on a network. EDS files describe a product device type,
revision, and configurable parameters.
Publication GMSI10-UM005C-EN-P - May 2010
Glossary
111
Help window
A window that contains help topics that describe the operation of a program.
These topics may include:
•
•
•
•
An explanation of a command.
A description of the controls in a dialog box or property page.
Instructions for a task.
Definition of a term.
MAC ID
See node address.
master device
A device which controls one or more slave devices. The XM-440 Master Relay
module is a master device.
node address
A DeviceNet network can have as many as 64 devices connected to it. Each
device on the network must have a unique node address between 0 and 63.
Node address 63 is the default used by uncommissioned devices. Node
address is sometimes called "MAC ID."
NVS (Non-Volatile Storage)
NVS is the permanent memory of an XM module. Modules store parameters
and other information in NVS so that they are not lost when the module loses
power (unless Auto Save is disabled). NVS is sometimes called "EEPROM."
online help
Online help allows you to get help for your program on the computer screen
by pressing F1. The help that appears in the Help window is context sensitive,
which means that the help is related to what you are currently doing in the
program.
Polled
DeviceNet communications method in which module sends data in response
to a poll request from a master device.
Publication GMSI10-UM005C-EN-P - May 2010
Glossary
112
Program mode
The XM module is idle. Typically this occurs when the module configuration
settings are being updated with the XM Configuration program. In Program
mode, the signal processing/measurement process is stopped, and the status
of the alarms is set to the disarm state to prevent a false alert or danger status.
Run mode
In Run mode, the module collects measurement data and monitors each
measurement device.
settling time
The amount of time it takes a measurement to reach 90% of the final value
given a step change in the input signal.
slave device
A device that receives and responds to messages from a Master device but
does not initiate communication. Slave devices include the XM measurement
modules, such as the XM-120 Dynamic Measurement module and the XM-320
Position module.
Strobe
See Bit-Strobe.
transducer
A transducer is a device for taking measurements. These include
accelerometers, velocity pickups, displacement probes, and temperature
sensors.
trend
A set of records of one or more measurement parameter(s) collected at regular
intervals of a base parameter such as time.
trigger
An event that prompts the collection of trend data.
triggered trend
A time-base trend that is collected in an XM module when a relay on the
module is activated, or when the module receives a trigger event.
Publication GMSI10-UM005C-EN-P - May 2010
Glossary
113
virtual relay
A virtual relay is a non-physical relay. It has the same capabilities (monitor
alarms, activation delay, change status) as a physical relay only without any
physical or electrical output. The virtual relay provides additional relay status
inputs to a controller, PLC, or an XM-440 Master Relay module (firmware
revision 5.0 and later).
XM configuration
XM configuration is a collection of user-defined parameters for XM modules.
XM Serial Configuration Utility software
XM Serial Configuration Utility software is a tool for monitoring and
configuring XM modules. It can be run on computers running Windows 2000
service pack 2, Windows NT 4.0 service pack 6, or Windows XP operating
systems.
Publication GMSI10-UM005C-EN-P - May 2010
Glossary
114
Publication GMSI10-UM005C-EN-P - May 2010
Index
Numerics
24V common grounding requirements 14
4-20mA Output Object 106
4-20mA output parameters 62
Enable 62
Max Range 62
Min Range 62
4-20mA outputs, wiring 29
A
Acknowledge Handler Object 98
Alarm Object 99
alarm parameters 55
Alert Threshold (High) 56
Alert Threshold (Low) 56
Condition 56
Danger Threshold (High) 56
Danger Threshold (Low) 56
Enable 55
Hysteresis 57
Name 55
Number 55
Startup Period 57
Threshold Multiplier 57
Analog Input Point Object 93
Assembly Object 87
Automatic Device Replacement (ADR) 80
B
baud rate 39
bit-strobe message format 79
C
channel parameters 46
Calibration Bias 48
Channel Name 46
DC Bias Time Constant 47
Eng. Units 46
Fault High 46
Fault Low 46
Measurement Mode 49
Mode 49
Output Data Unit 46
Sensitivity 46
Target Angle 47
Upscale 47
Channel Status indicator 42
Class Instance Editor 75
components
terminal base XM-940 3
XM-320 Position module 4
XM-441 Expansion Relay module 4
configuration parameters 45
4-20mA output parameters 62
alarm parameters 55
channel parameters 46
data parameters 66
device mode parameters 68
I/O data parameters 65
relay parameters 58
triggered trend parameters 63
connecting wiring 19
4-20mA outputs 29
DeviceNet 38
power supply 22
relays 23
remote relay reset signal 27
serial port 36
setpoint multiplication switch 29
short circuit protected outputs 26
terminal base XM-941 19
transducers 30
Connection Object 90
COS message format 78
D
data parameters 66
4-20mA Output A 66
4-20mA Output B 66
Alarm Status 67
Channel Status 66
Measurement Value 66
Relay Status 67
Transducer DC Bias 66
Transducer Fault 66
description
configuration parameters 45
terminal base XM-940 3
XM-320 module 4
XM-441 module 4
Device Mode Object 101
Device Mode parameter 68, 73
device mode parameters 68
Autobaud 68
Device Mode 68, 73
Publication GMSI10-UM005C-EN-P - May 2010
116
Index
DeviceNet connection
baud rate 39
node address 39
wiring 38
DeviceNet grounding requirements 14
DeviceNet information
automatic device replacement (ADR) 80
EDS files 73
I/O message formats 77
invalid device configuration errors 76
setting the Device Mode parameter 73
XM services 75
DeviceNet Object 85
DeviceNet objects
4-20mA Output 106
Acknowledge Handler 98
Alarm 99
Analog Input Point 93
Assembly 87
Connection 90
Device Mode 101
DeviceNet 85
Discrete Input Point 92
Identity 84
Parameter 95
Relay 102
Transducer 105
DIN Rail Grounding Block 11
DIN rail grounding requirements 10
Discrete Input Point Object 92
document conventions 5
E
Electronic Data Sheet (EDS) files 73
G
grounding requirements 10
24V common 14
DeviceNet 14
DIN rail 10
panel/wall mount 12
switch input 15
transducers 14
H
head-to-head mode 51
Publication GMSI10-UM005C-EN-P - May 2010
I
I/O data parameters 65
Assembly Instance Table 65
COS Output 65
COS Size 65
Custom Assembly 65
Poll Output 65
Poll Response Assembly 65
Poll Size 65
I/O message formats
bit-strobe messages 79
change of state (COS) messages 78
poll messages 77
XM status values 78
Identity Object 84
indicators 41
Channel Status 42
Module Status 41
Network Status 42
Relay 42
Setpoint Multiplier 42
installation requirements
grounding 10
power 8
wiring 8
interconnecting terminal base units 17
introduction 1
invalid device configuration errors 76
K
keyswitch 39
M
modes
head-to-head 49, 51, 95
normal 49, 95
radial cancel 49, 54, 95
Module Status (MS) indicator 41
mounting
terminal base unit on DIN rail 15
terminal base unit on panel/walll 18
XM-320 module on terminal base 39
N
Network Status (NS) indicator 42
node address 39
normal mode 49
Index
normally closed relay contacts 23
normally open relay contacts 23
O
operating mode
program mode 41, 73
run mode 41, 73
P
panel/wall mount grounding requirements 12
Parameter Object 95
poll message format 77
power requirements 8
power supply, wiring 22
program mode 41, 73
R
radial cancel mode 54
relay contacts
normally closed 23
normally open 23
Relay indicator 42
Relay Object 102
relay parameters 58
Activation Delay 59
Activation Logic 59
Alarm A 59
Alarm B 59
Alarm Identifier A 59
Alarm Identifier B 59
Alarm Levels 60
Alarm Status to Activate On 60
Enable 58
Failsafe 61
Latching 59
Name 58
Number 58
Relay Installed 60
relays
resetting 27, 43
wiring 23
remote relay reset signal, wiring 27
reset switch 43
run mode 41, 73
117
S
self-test, status 43
serial port connection
mini-connector 37
terminal base unit 36
setpoint multiplication switch, wiring 29
Setpoint Multiplier indicator 42
short circuit protected output, wiring 26
specifications 69
switch input grounding requirements 15
T
terminal base
interconnecting units 17
mounting on DIN rail 15
mounting on panel/wall 18
terminal block assignment 20
transducer grounding requirements 14
Transducer Object 105
transducer wiring 30
cam potentiometer 33
linear variable differential transformer (LVDT) 32
non-contact sensor 30
non-contact sensor and LVDT 35
transition to program mode, DeviceNet 74
transition to run mode, DeviceNet 74
triggered trend parameters 63
Enable Triggered Trend Measurements 63
Latch Enable 63
Manual Trigger 64
Number of Records 63
Post Trigger 64
Record Interval 64
Relay Number 64
Reset Trigger 64
Select Measurements 63
Status 64
Trend Span 64
View Trend Data 64
W
wiring
to separate power connections 8
to terminal base 19
Publication GMSI10-UM005C-EN-P - May 2010
118
Index
wiring connections
4-20mA outputs 29
DeviceNet 38
power supply 22
relays 23
remote relay reset signal 27
serial port 36
setpoint multiplication switch 29
short circuit protected output 26
transducers 30
wiring requirements 8
X
XM Services 75
XM status values 78
XM-320 I/O message formats 77
Publication GMSI10-UM005C-EN-P - May 2010
XM-320 Position Module
components 3
configuration parameters 45
description 4
grounding requirements 10
indicators 41
introduction 1
mounting 39
power requirement 8
reset switch 43
self-test 43
specifications 69
wiring requirements 8
XM-441 Expansion Relay Module 4, 44, 58
XM-941 terminal base
description 3
mounting 15
wiring 19
Rockwell Automation
Support
Rockwell Automation provides technical information on the Web to assist you in using
its products. At http://support.rockwellautomation.com, you can find technical manuals, a
knowledge base of FAQs, technical and application notes, sample code and links to
software service packs, and a MySupport feature that you can customize to make the
best use of these tools.
For an additional level of technical phone support for installation,
configuration, and troubleshooting, we offer TechConnect support programs.
For more information, contact your local distributor or Rockwell Automation
representative, or visit http://support.rockwellautomation.com.
Installation Assistance
If you experience a problem within the first 24 hours of installation, please
review the information that's contained in this manual. You can also contact
a special Customer Support number for initial help in getting your product up
and running.
United States
1.440.646.3434
Monday – Friday, 8am – 5pm EST
Outside United
States
Please contact your local Rockwell Automation representative for any
technical support issues.
New Product Satisfaction Return
Rockwell Automation tests all of its products to ensure that they are fully
operational when shipped from the manufacturing facility. However, if your
product is not functioning and needs to be returned, follow these
procedures.
United States
Contact your distributor. You must provide a Customer Support case
number (call the phone number above to obtain one) to your distributor
in order to complete the return process.
Outside United
States
Please contact your local Rockwell Automation representative for the
return procedure.
Publication GMSI10-UM005C-EN-P - May 2010 119
Supersedes Publication GMSI10-UM005B-EN-E - March 2006
Copyright © 2010 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement