Yokogawa EJA 210A, EJA 220A pressure transmitter User's Manual

User’s
Manual
Model EJA210A and EJA220A
Flange Mounted Differential
Pressure Transmitters
IM 01C21C01-01E
IM 01C21C01-01E
Yokogawa Electric Corporation
11th Edition
CONTENTS
CONTENTS
1.
INTRODUCTION ............................................................................................ 1-1
Regarding This Manual ................................................................................. 1-1
1.1 For Safe Use of Product ........................................................................ 1-1
1.2 Warranty ................................................................................................ 1-2
1.3 ATEX Documentation ............................................................................ 1-3
2.
HANDLING CAUTIONS ................................................................................ 2-1
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
Model and Specifications Check ......................................................... 2-1
Unpacking ........................................................................................... 2-1
Storage ................................................................................................ 2-1
Selecting the Installation Location ...................................................... 2-1
Pressure Connection ........................................................................... 2-2
Waterproofing of Cable Conduit Connections .................................... 2-2
Restrictions on Use of Radio Transceiver .......................................... 2-2
Insulation Resistance and Dielectric Strength Test ............................ 2-2
Installation of Explosion Protected Type ............................................ 2-3
2.9.1 FM Approval ................................................................................. 2-3
2.9.2 CSA Certification .......................................................................... 2-5
2.9.3 IECEx Certification ....................................................................... 2-6
2.9.4 CENELEC ATEX (KEMA) Certification ........................................ 2-8
2.10 EMC Conformity Standards .............................................................. 2-10
2.11 PED (Pressure Equipment Directive) ............................................... 2-10
2.12 Low Voltage Directive ....................................................................... 2-11
3.
COMPONENT NAMES .................................................................................. 3-1
4.
INSTALLATION ............................................................................................. 4-1
4.1
4.2
4.3
4.4
4.5
5.
Precautions ......................................................................................... 4-1
Mounting .............................................................................................. 4-1
Rotating Transmitter Section .............................................................. 4-1
Changing the Direction of Integral Indicator ....................................... 4-2
Affixing the Teflon Film ....................................................................... 4-2
INSTALLING IMPULSE PIPING ................................................................... 5-1
5.1
Impulse Piping Installation Precautions .............................................. 5-1
5.1.1 Connecting Impulse Piping to the Transmitter ............................. 5-1
5.1.2 Routing the Impulse Piping .......................................................... 5-1
5.2 Impulse Piping Connection Examples ................................................ 5-2
6.
WIRING .......................................................................................................... 6-1
6.1
6.2
6.3
Wiring Precautions .............................................................................. 6-1
Selecting the Wiring Materials ............................................................ 6-1
Connections of External Wiring to Terminal Box ................................ 6-1
6.3.1 Power Supply Wiring Connection ................................................ 6-1
6.3.2 External Indicator Connection ...................................................... 6-1
6.3.3 BRAIN TERMINAL BT200 Connection ........................................ 6-1
6.3.4 Check Meter Connection .............................................................. 6-2
FD No. IM 01C21C01-01E
11th Edition: Oct. 2008(KP)
All Rights Reserved, Copyright © 1997, Yokogawa Electric Corporation
i
IM 01C21C01-01E
CONTENTS
6.4
Wiring .................................................................................................. 6-2
6.4.1 Loop Configuration ....................................................................... 6-2
(1) General-use Type and Flameproof Type ..................................... 6-2
(2) Intrinsically Safe Type ................................................................. 6-2
6.4.2 Wiring Installation ......................................................................... 6-2
(1) General-use Type and Intrinsically Safe Type............................. 6-2
(2) Flameproof Type ......................................................................... 6-3
6.5 Grounding ............................................................................................ 6-3
6.6 Power Supply Voltage and Load Resistance ..................................... 6-3
7.
OPERATION .................................................................................................. 7-1
7.1
7.2
Preparation for Starting Operation ...................................................... 7-1
Zero Point Adjustment ........................................................................ 7-2
7.2.1 When you can obtain Low Range Value from actual
measured value of 0% (0 kPa, atmospheric pressure); .............. 7-2
7.2.2 When you cannot obtain Low Range Value from actual
measured value of 0%; ................................................................ 7-3
7.3 Starting Operation ............................................................................... 7-3
7.4 Shutting Down Operation .................................................................... 7-3
7.5 Venting or Draining Transmitter Pressure-detector Section ............... 7-3
7.5.1 Draining Condensate .................................................................... 7-4
7.5.2 Venting Gas .................................................................................. 7-4
7.6 Setting the Range Using the Range-setting Switch ........................... 7-4
8.
BRAIN TERMINAL BT200 OPERATION ..................................................... 8-1
8.1
BT200 Operation Precautions ............................................................. 8-1
8.1.1 Connecting the BT200 ................................................................. 8-1
8.1.2 Conditions of Communication Line .............................................. 8-1
8.2 BT200 Operating Procedures ............................................................. 8-1
8.2.1 Key Layout and Screen Display ................................................... 8-1
8.2.2 Operating Key Functions .............................................................. 8-2
(1) Alphanumeric Keys and Shift Keys ............................................. 8-2
(2) Function Keys ............................................................................. 8-2
8.2.3 Calling Up Menu Addresses Using the Operating Keys .............. 8-3
8.3 Setting Parameters Using the BT200 ................................................. 8-4
8.3.1 Parameter Summary .................................................................... 8-4
8.3.2 Parameter Usage and Selection .................................................. 8-6
8.3.3 Setting Parameters ....................................................................... 8-7
(1) Tag No. Setup ............................................................................. 8-7
(2) Calibration Range Setup ............................................................. 8-7
(3) Damping Time Constant Setup ................................................... 8-8
(4) Output Signal Low Cut Mode Setup ............................................ 8-9
(5) Change Output Limits ................................................................. 8-9
(6) Integral Indicator Scale Setup ..................................................... 8-9
(7) Unit Setup for Displayed Temperature ...................................... 8-11
(8) Unit Setup for Displayed Static Pressure .................................. 8-11
(9) Operation Mode Setup .............................................................. 8-11
(10) Output Status Display/Setup when a CPU Failure .................... 8-12
(11) Output Status Setup when a Hardware Error Occurs ............... 8-12
(12) Range Change while Applying Actual Inputs ............................ 8-12
(13) Zero Point Adjustment ............................................................... 8-13
(14) Span Adjustment ....................................................................... 8-14
(15) Test Output Setup ..................................................................... 8-15
(16) User Memo Fields ..................................................................... 8-15
ii
IM 01C21C01-01E
CONTENTS
8.4
Displaying Data Using the BT200 ..................................................... 8-16
8.4.1 Displaying Measured Data ......................................................... 8-16
8.4.2 Display Transmitter Model and Specifications ........................... 8-16
8.5 Self-Diagnostics ................................................................................ 8-16
8.5.1 Checking for Problems ............................................................... 8-16
(1) Identifying Problems with BT200 .............................................. 8-16
(2) Checking with Integral Indicator ................................................ 8-17
8.5.2 Errors and Countermeasures ..................................................... 8-18
9.
MAINTENANCE ............................................................................................. 9-1
9.1
9.2
9.3
9.4
Overview ............................................................................................. 9-1
Calibration Instruments Selection ....................................................... 9-1
Calibration ........................................................................................... 9-1
Disassembly and Reassembly ............................................................ 9-3
9.4.1 Replacing the Integral Indicator ................................................... 9-3
9.4.2 Replacing the CPU Board Assembly ........................................... 9-4
9.4.3 Replacing the Process Connector Gasket ................................... 9-5
9.5 Troubleshooting ................................................................................... 9-5
9.5.1 Basic Troubleshooting .................................................................. 9-5
9.5.2 Troubleshooting Flow Charts ....................................................... 9-6
10. GENERAL SPECIFICATIONS .................................................................... 10-1
10.1
10.2
10.3
10.4
Standard Specifications .................................................................... 10-1
Model and Suffix Codes .................................................................... 10-3
Optional Specifications ...................................................................... 10-5
Dimensions ........................................................................................ 10-8
Customer Maintenance Parts List
DPharp EJA Series Transmitter Section ........................ CMPL 01C21A01-02E
Model EJA210A and EJA220A Flange Mounted
Differential Pressure Transmitter ................................... CMPL 01C21C01-01E
REVISION RECORD
iii
IM 01C21C01-01E
1. INTRODUCTION
1.
INTRODUCTION
Thank you for purchasing the DPharp electronic
pressure transmitter.
• The following safety symbol marks are used in this
manual:
The DPharp Pressure Transmitters are precisely
calibrated at the factory before shipment. To ensure
correct and efficient use of the instrument, please read
this manual thoroughly and fully understand how to
operate the instrument before operating it.
WARNING
Indicates a potentially hazardous situation which,
if not avoided, could result in death or serious
injury.
Regarding This Manual
• This manual should be passed on to the end user.
• The contents of this manual are subject to change
without prior notice.
CAUTION
Indicates a potentially hazardous situation which,
if not avoided, may result in minor or moderate
injury. It may also be used to alert against
unsafe practices.
• All rights reserved. No part of this manual may be
reproduced in any form without Yokogawa’s written
permission.
• Yokogawa makes no warranty of any kind with
regard to this manual, including, but not limited to,
implied warranty of merchantability and fitness for a
particular purpose.
IMPORTANT
• If any question arises or errors are found, or if any
information is missing from this manual, please
inform the nearest Yokogawa sales office.
Indicates that operating the hardware or software
in this manner may damage it or lead to system
failure.
• The specifications covered by this manual are
limited to those for the standard type under the
specified model number break-down and do not
cover custom-made instruments.
NOTE
Draws attention to information essential for
understanding the operation and features.
• Please note that changes in the specifications,
construction, or component parts of the instrument
may not immediately be reflected in this manual at
the time of change, provided that postponement of
revisions will not cause difficulty to the user from a
functional or performance standpoint.
• Yokogawa assumes no responsibilities for this
product except as stated in the warranty.
• If the customer or any third party is harmed by the
use of this product, Yokogawa assumes no responsibility for any such harm owing to any defects in the
product which were not predictable, or for any
indirect damages.
Direct current
1.1 For Safe Use of Product
For the protection and safety of the operator and the
instrument or the system including the instrument,
please be sure to follow the instructions on safety
described in this manual when handling this instrument. In case the instrument is handled in contradiction
to these instructions, Yokogawa does not guarantee
safety. Please give your attention to the followings.
NOTE
(a) Installation
• The instrument must be installed by an expert
engineer or a skilled personnel. The procedures
described about INSTALLATION are not permitted
for operators.
For FOUNDATION FieldbusTM, PROFIBUS PA and
HART protocol versions, please refer to IM
01C22T02-01E, IM 01C22T03-00E and IM
01C22T01-01E respectively, in addition to this
manual.
1-1
IM 01C21C01-01E
1. INTRODUCTION
(f) Modification
• Yokogawa will not be liable for malfunctions or
damage resulting from any modification made to this
instrument by the customer.
• In case of high process temperature, care should be
taken not to burn yourself because the surface of
body and case reaches a high temperature.
• The instrument installed in the process is under
pressure. Never loosen the process connector bolts to
avoid the dangerous spouting of process fluid.
1.2 Warranty
• The warranty shall cover the period noted on the
quotation presented to the purchaser at the time of
purchase. Problems occurred during the warranty
period shall basically be repaired free of charge.
• During draining condensate from the pressuredetector section, take appropriate care to avoid
contact with the skin, eyes or body, or inhalation of
vapors, if the accumulated process fluid may be
toxic or otherwise harmful.
• In case of problems, the customer should contact the
Yokogawa representative from which the instrument
was purchased, or the nearest Yokogawa office.
• When removing the instrument from hazardous
processes, avoid contact with the fluid and the
interior of the meter.
• If a problem arises with this instrument, please
inform us of the nature of the problem and the
circumstances under which it developed, including
the model specification and serial number. Any
diagrams, data and other information you can
include in your communication will also be helpful.
• All installation shall comply with local installation
requirement and local electrical code.
(b) Wiring
• The instrument must be installed by an expert
engineer or a skilled personnel. The procedures
described about WIRING are not permitted for
operators.
• Responsible party for repair cost for the problems
shall be determined by Yokogawa based on our
investigation.
• Please confirm that voltages between the power
supply and the instrument before connecting the
power cables and that the cables are not powered
before connecting.
• The Purchaser shall bear the responsibility for repair
costs, even during the warranty period, if the
malfunction is due to:
- Improper and/or inadequate maintenance by the
purchaser.
- Failure or damage due to improper handling, use or
storage which is out of design conditions.
- Use of the product in question in a location not
conforming to the standards specified by
Yokogawa, or due to improper maintenance of the
installation location.
- Failure or damage due to modification or repair by
any party except Yokogawa or an approved
representative of Yokogawa.
- Malfunction or damage from improper relocation
of the product in question after delivery.
- Reason of force majeure such as fires, earthquakes,
storms/floods, thunder/lightening, or other natural
disasters, or disturbances, riots, warfare, or
radioactive contamination.
(c) Operation
• Wait 10 min. after power is turned off, before
opening the covers.
(d) Maintenance
• Please do not carry out except being written to a
maintenance descriptions. When these procedures
are needed, please contact nearest YOKOGAWA
office.
• Care should be taken to prevent the build up of drift,
dust or other material on the display glass and
name plate. In case of its maintenance, soft and dry
cloth is used.
(e) Explosion Protected Type Instrument
• Users of explosion proof instruments should refer
first to section 2.9 (Installation of an Explosion
Protected Instrument) of this manual.
• The use of this instrument is restricted to those who
have received appropriate training in the device.
• Take care not to create sparks when accessing the
instrument or peripheral devices in a hazardous
location.
1-2
IM 01C21C01-01E
1. INTRODUCTION
1.3 ATEX Documentation
SF
This procedure is only applicable to the countries in
European Union.
Kaikkien ATEX Ex -tyyppisten tuotteiden käyttöhjeet
ovat saatavilla englannin-, saksan- ja ranskankielisinä.
Mikäli tarvitsette Ex -tyyppisten tuotteiden ohjeita
omalla paikallisella kielellännne, ottakaa yhteyttä
lähimpään Yokogawa-toimistoon tai -edustajaan.
GB
All instruction manuals for ATEX Ex related products
are available in English, German and French. Should
you require Ex related instructions in your local
language, you are to contact your nearest Yokogawa
office or representative.
P
Todos os manuais de instruções referentes aos produtos
Ex da ATEX estão disponíveis em Inglês, Alemão e
Francês. Se necessitar de instruções na sua língua
relacionadas com produtos Ex, deverá entrar em
contacto com a delegação mais próxima ou com um
representante da Yokogawa.
DK
Alle brugervejledninger for produkter relateret til
ATEX Ex er tilgængelige på engelsk, tysk og fransk.
Skulle De ønske yderligere oplysninger om håndtering
af Ex produkter på eget sprog, kan De rette
henvendelse herom til den nærmeste Yokogawa
afdeling eller forhandler.
F
Tous les manuels d’instruction des produits ATEX Ex
sont disponibles en langue anglaise, allemande et
française. Si vous nécessitez des instructions relatives
aux produits Ex dans votre langue, veuillez bien
contacter votre représentant Yokogawa le plus proche.
I
Tutti i manuali operativi di prodotti ATEX
contrassegnati con Ex sono disponibili in inglese,
tedesco e francese. Se si desidera ricevere i manuali
operativi di prodotti Ex in lingua locale, mettersi in
contatto con l’ufficio Yokogawa più vicino o con un
rappresentante.
D
Alle Betriebsanleitungen für ATEX Ex bezogene
Produkte stehen in den Sprachen Englisch, Deutsch
und Französisch zur Verfügung. Sollten Sie die
Betriebsanleitungen für Ex-Produkte in Ihrer
Landessprache benötigen, setzen Sie sich bitte mit
Ihrem örtlichen Yokogawa-Vertreter in Verbindung.
E
Todos los manuales de instrucciones para los productos
antiexplosivos de ATEX están disponibles en inglés,
alemán y francés. Si desea solicitar las instrucciones de
estos artículos antiexplosivos en su idioma local,
deberá ponerse en contacto con la oficina o el
representante de Yokogawa más cercano.
S
Alla instruktionsböcker för ATEX Ex (explosionssäkra)
produkter är tillgängliga på engelska, tyska och
franska. Om Ni behöver instruktioner för dessa
explosionssäkra produkter på annat språk, skall Ni
kontakta närmaste Yokogawakontor eller representant.
NL
Alle handleidingen voor producten die te maken
hebben met ATEX explosiebeveiliging (Ex) zijn
verkrijgbaar in het Engels, Duits en Frans. Neem,
indien u aanwijzingen op het gebied van
explosiebeveiliging nodig hebt in uw eigen taal, contact
op met de dichtstbijzijnde vestiging van Yokogawa of
met een vertegenwoordiger.
GR
ATEX Ex
, .
Ex Yokogawa .
1-3
IM 01C21C01-01E
1. INTRODUCTION
PL
SK
CZ
SLO
H
LT
BG
LV
RO
EST
M
1-4
IM 01C21C01-01E
2. HANDLING CAUTIONS
2.
HANDLING CAUTIONS
This chapter describes important cautions regarding
how to handle the transmitter. Read carefully before
using the transmitter.
The EJA-A Series pressure transmitters are thoroughly
tested at the factory before shipment. When the
transmitter is delivered, visually check them to make
sure that no damage occurred during shipment.
Also check that all transmitter mounting hardware
shown in Figure 2.1 is included. If the transmitter was
ordered without the mounting bracket or without the
process connector, the transmitter mounting hardware
is not included. After checking the transmitter, repack
it in the way it was delivered until installation.
Process connector
Bolt
Process connector gasket
F0201.EPS
Figure 2.1 Transmitter Mounting Hardware
2.3 Storage
The following precautions must be observed when
storing the instrument, especially for a long period.
(a) Select a storage area which meets the following
conditions:
• It is not exposed to rain or water.
• It suffers minimum vibration and shock.
• It has an ambient temperature and relative
humidity within the following ranges.
Ambient temperature:
–40 to 85°C without integral indicator
–30 to 80°C with integral indicator
Relative humidity:
5% to 100% R.H. (at 40°C)
Preferred temperature and humidity:
approx. 25°C and 65% R.H.
(b) When storing the transmitter, repack it as nearly as
possible to the way it was packed when delivered
from the factory.
(c) If storing a transmitter that has been used, thoroughly clean the chambers inside the cover flanges,
so that no measured fluid remains in it. Also make
sure before storing that the pressure-detector and
transmitter section are securely mounted.
2.1 Model and Specifications
Check
2.4 Selecting the Installation
Location
The model name and specifications are indicated on the
name plate attached to the case. If the reverse operating mode was ordered (reverse signal), ‘REVERSE’
will be inscribed in field *1.
The transmitter is designed to withstand severe
environmental conditions. However, to ensure stable
and accurate operation for years, observe the following
precautions when selecting an installation location.
: Refer to USER'S MANUAL
F0202.EPS
Figure 2.2 Name Plate
2.2 Unpacking
When moving the transmitter to the installation site,
keep it in its original packaging. Then, unpack the
transmitter there to avoid damage on the way.
(a) Ambient Temperature
Avoid locations subject to wide temperature
variations or a significant temperature gradient. If
the location is exposed to radiant heat from plant
equipments, provide adequate thermal insulation
and/or ventilation.
(b) Ambient Atmosphere
Avoid installing the transmitter in a corrosive
atmosphere. If the transmitter must be installed in a
corrosive atmosphere, there must be adequate
ventilation as well as measures to prevent intrusion
or stagnation of rain water in conduits.
2-1
IM 01C21C01-01E
2. HANDLING CAUTIONS
effects, bring the transceiver in use slowly from a
distance of several meters from the transmitter,
and observe the measurement loop for noise
effects. Thereafter, always use the transceiver
outside the area affected by noise.
(c) Shock and Vibration
Select an installation site suffering minimum shock
and vibration (although the transmitter is designed
to be relatively resistant to shock and vibration).
(d) Installation of Explosion-protected Transmitters
Explosion-protected transmitters can be installed in
hazardous areas according to the types of gases for
which they are certified. See Subsection 2.9
“Installation of Explosion Protected Type Transmitters.”
2.5 Pressure Connection
WARNING
• Instrument installed in the process is under
pressure. Never loosen the process connector
bolts to avoid the dangerous spouting of
process fluid.
• During draining condensate from the pressuredetector section, take appropriate care to avoid
contact with the skin, eyes or body, or inhalation of vapors, if the accumulated process fluid
may be toxic or otherwise harmful.
The following precautions must be observed in order to
safely operate the transmitter under pressure.
(a) Make sure that the two process connector bolts are
tightened firmly.
(b) Make sure that there are no leaks in the impulse
piping.
(c) Never apply a pressure higher than the specified
maximum working pressure.
2.6 Waterproofing of Cable
Conduit Connections
Apply a non-hardening sealant to the threads to
waterproof the transmitter cable conduit connections.
(See Figure 6.4.2a, 6.4.2b and 6.4.2c.)
2.7 Restrictions on Use of Radio
Transceiver
IMPORTANT
Although the transmitter has been designed to
resist high frequency electrical noise, if a radio
transceiver is used near the transmitter or its
external wiring, the transmitter may be affected
by high frequency noise pickup. To test for such
2.8 Insulation Resistance and
Dielectric Strength Test
Since the transmitter has undergone insulation resistance and dielectric strength tests at the factory before
shipment, normally these tests are not required.
However, if required, observe the following precautions in the test procedures.
(a) Do not perform such tests more frequently than is
absolutely necessary. Even test voltages that do not
cause visible damage to the insulation may degrade
the insulation and reduce safety margins.
(b) Never apply a voltage exceeding 500 V DC (100 V
DC with an internal lightning protector) for the
insulation resistance test, nor a voltage exceeding
500 V AC (100 V AC with an internal lightning
protector) for the dielectric strength test.
(c) Before conducting these tests, disconnect all signal
lines from the transmitter terminals. Perform the
tests in the following procedure:
• Insulation Resistance Test
1) Short-circuit the + and – SUPPLY terminals in the
terminal box.
2) Turn OFF the insulation tester. Then connect the
insulation tester plus (+) lead wire to the shorted
SUPPLY terminals and the minus (–) leadwire to
the grounding terminal.
3) Turn ON the insulation tester power and measure
the insulation resistance. The voltage should be
applied short as possible to verify that the insulation resistance is at least 20 MΩ.
4) After completing the test and being very careful not
to touch exposed conductors disconnect the
insulation tester and connect a 100 kΩ resistor
between the grounding terminal and the shortcircuiting SUPPLY terminals. Leave this resistor
connected at least one second to discharge any
static potential. Do not touch the terminals while it
is discharging.
• Dielectric Strength Test
1) Short-circuit the + and – SUPPLY terminals in the
terminal box.
2-2
IM 01C21C01-01E
2. HANDLING CAUTIONS
2) Turn OFF the dielectric strength tester. Then
connect the tester between the shorted SUPPLY
terminals and the grounding terminal. Be sure to
connect the grounding lead of the dielectric strength
tester to the ground terminal.
3) Set the current limit on the dielectric strength tester
to 10 mA, then turn ON the power and gradually
increase the test voltage from ‘0’ to the specified
voltage.
4) When the specified voltage is reached, hold it for
one minute.
5) After completing this test, slowly decrease the
voltage to avoid any voltage surges.
2.9 Installation of Explosion
Protected Type
In this section, further requirements and differences
and for explosionproof type instrument are described.
For explosionproof type instrument, the description in
this chapter is prior to other description in this users
manual.
For the intrinsically safe equipment and explosionproof
equipment, in case the instrument is not restored to its
original condition after any repair or modification
undertaken by the customer, intrinsically safe construction or explosionproof construction is damaged and
may cause dangerous condition. Please contact
Yokogawa for any repair or modification required to
the instrument.
NOTE
For FOUNDATION Fieldbus and PROFIBUS PA
explosion protected type, please refer to IM
01C22T02-01E and IM 01C22T03-00E respectively.
CAUTION
WARNING
To preserve the safety of explosionproof equipment requires great care during mounting,
wiring, and piping. Safety requirements also
place restrictions on maintenance and repair
activities. Please read the following sections very
carefully.
2.9.1 FM Approval
a. FM Intrinsically Safe Type
Caution for FM intrinsically safe type. (Following
contents refer “DOC. No. IFM012-A12 P.1 and 2.”)
Note 1. Model EJA Series pressure transmitters
with optional code /FS1 are applicable for
use in hazardous locations.
• Applicable Standard: FM3600, FM3610, FM3611,
FM3810, ANSI/NEMA250
• Intrinsically Safe for Class I, Division 1, Groups A,
B, C & D. Class II, Division 1, Groups E, F & G
and Class III, Division 1 Hazardous Locations.
• Nonincendive for Class I, Division 2, Groups A, B,
C & D. Class II, Division 2, Groups E, F & G and
Class III, Division 1 Hazardous Locations.
• Outdoor hazardous locations, NEMA 4X.
• Temperature Class: T4
• Ambient temperature: –40 to 60°C
Note 2. Entity Parameters
• Intrinsically Safe Apparatus Parameters
[Groups A, B, C, D, E, F and G]
Vmax = 30 V
Ci = 22.5 nF
Imax = 165 mA
Li = 730 µH
Pmax = 0.9 W
* Associated Apparatus Parameters
(FM approved barriers)
Voc ≤ 30 V
Ca > 22.5 nF
Isc ≤ 165 mA
La > 730 µH
Pmax ≤ 0.9W
• Intrinsically Safe Apparatus Parameters
[Groups C, D, E, F and G]
Vmax = 30 V
Ci = 22.5 nF
Imax = 225 mA
Li = 730 µH
Pmax = 0.9 W
* Associated Apparatus Parameters
(FM approved barriers)
Voc ≤ 30 V
Ca > 22.5 nF
Isc ≤ 225 mA
La > 730 µH
Pmax ≤ 0.9 W
This instrument is tested and certified as intrinsically safe type or explosionproof type. Please
note that the construction of the instrument,
installation, external wiring, maintenance or
repair is strictly restricted, and non-observance
or negligence of this restriction would result in
dangerous condition.
• Entity Installation Requirements
Vmax ≥ Voc or Vt, Imax ≥ Isc or It,
Pmax (IS Apparatus) ≥ Pmax (Barrier)
Ca ≥ Ci + Ccable, La ≥ Li + Lcable
2-3
IM 01C21C01-01E
2. HANDLING CAUTIONS
b. FM Explosionproof Type
Caution for FM explosionproof type.
Note 3. Installation
• Barrier must be installed in an enclosure that meets
the requirements of ANSI/ISA S82.01.
• Control equipment connected to barrier must not use
or generate more than 250 V rms or V dc.
• Installation should be in accordance with ANSI/ISA
RP12.6 “Installation of Intrinsically Safe Systems for
Hazardous (Classified) Locations” and the National
Electric Code (ANSI/NFPA 70).
• The configuration of associated apparatus must be
FMRC Approved.
• Dust-tight conduit seal must be used when installed
in a Class II, III, Group E, F and G environments.
• Associated apparatus manufacturer’s installation
drawing must be followed when installing this
apparatus.
• The maximum power delivered from the barrier
must not exceed 0.9 W.
• Note a warning label worded “SUBSTITUTION OF
COMPONENTS MAY IMPAIR INTRINSIC
SAFETY,” and “INSTALL IN ACCORDANCE
WITH DOC. No. IFM012-A12 P.1 and 2.”
Note 4. Maintenance and Repair
• The instrument modification or parts replacement by
other than authorized representative of Yokogawa
Electric Corporation is prohibited and will void
Factory Mutual Intrinsically safe and Nonincendive
Approval.
Note 1. Model EJA Series differential, gauge,
and absolute pressure transmitters with
optional code /FF1 are applicable for
use in hazardous locations.
• Applicable Standard: FM3600, FM3615, FM3810,
ANSI/NEMA250
• Explosionproof for Class I, Division 1, Groups B,
C and D.
• Dust-ignitionproof for Class II/III, Division 1,
Groups E, F and G.
• Outdoor hazardous locations, NEMA 4X.
• Temperature Class: T6
• Ambient Temperature: –40 to 60°C
• Supply Voltage: 42 V dc max.
• Output signal: 4 to 20 mA
Note 2. Wiring
• All wiring shall comply with National Electrical
Code ANSI/NEPA70 and Local Electrical Codes.
• When installed in Division 1, “FACTORY
SEALED, CONDUIT SEAL NOT REQUIRED.”
Note 3. Operation
• Keep the “CAUTION” nameplate attached to the
transmitter.
CAUTION: OPEN CIRCUIT BEFORE REMOVING COVER. FACTORY SEALED, CONDUIT
SEAL NOT REQUIRED. INSTALL IN ACCORDANCE WITH THE INSTRUCTION MANUAL
IM 1C22.
• Take care not to generate mechanical sparking
when accessing to the instrument and peripheral
devices in a hazardous location.
[Intrinsically Safe]
Hazardous Location
Nonhazardous Location
Class I, II, III, Division 1,
Groups A, B, C, D, E, F, G
EJA Series Pressure
Transmitters
+
Supply
–
Safety Barrier
+
+
–
–
General
Purpose
Equipment
+
Note 4. Maintenance and Repair
• The instrument modification or parts replacement
by other than authorized representative of
Yokogawa Electric Corporation is prohibited and
will void Factory Mutual Explosionproof Approval.
–
[Nonincendive]
Hazardous Location
Nonhazardous Location
Class I, II, Division 2,
Groups A, B, C, D, E, F, G
Class III, Division 1.
EJA Series Pressure
Transmitters
+
Supply
c. FM Intrinsically Safe Type/FM
Explosionproof Type
Model EJA Series pressure transmitters with
optional code /FU1 can be selected the type
of protection (FM Intrinsically Safe or FM
Explosionproof) for use in hazardous locations.
Note 1. For the installation of this transmitter,
once a particular type of protection is
selected, any other type of protection
cannot be used. The installation must be
in accordance with the description about
the type of protection in this instruction
manual.
General
Purpose
Equipment
+
–
–
Not Use
Safety Barrier
F0203.EPS
2-4
IM 01C21C01-01E
2. HANDLING CAUTIONS
Note 2. In order to avoid confusion, unnecessary
marking is crossed out on the label other
than the selected type of protection when
the transmitter is installed.
[Intrinsically Safe]
Hazardous Location
Class I, II, III, Division 1,
Groups A, B, C, D, E, F, G
EJA Series Pressure
Transmitters
+
2.9.2 CSA Certification
a. CSA Intrinsically Safe Type
Caution for CSA Intrinsically safe type. (Following
contents refer to “DOC No. ICS003-A12 P.1-1 and
P.1-2.”)
Note 1. Model EJA Series differential, gauge, and
absolute pressure transmitters with
optional code /CS1 are applicable for use
in hazardous locations
Certificate: 1053843
• Applicable Standard: C22.2 No.0, No.0.4, No.25,
No.30, No.94, No.142, No.157, No.213
• Intrinsically Safe for Class I, Division 1, Groups A,
B, C & D. Class II, Division 1, Groups E, F & G
and Class III, Division 1 Hazardous Locations.
• Nonincendive for Class I, Division 2, Groups A, B,
C & D, Class II, Division 2, Groups F & G, and
Class III, Hazardous Locations. (not use Safety
Barrier)
• Encl. “Type 4X”
• Temperature Class: T4
• Ambient temperature: –40 to 60°C
• Process Temperature: 120°C max.
Note 2. Entity Parameters
• Intrinsically safe ratings are as follows:
Maximum Input Voltage (Vmax) = 30 V
Maximum Input Current (Imax) = 165 mA
Maximum Input Power (Pmax) = 0.9 W
Maximum Internal Capacitance (Ci) = 22.5 nF
Maximum Internal Inductance (Li) = 730 µH
* Associated apparatus (CSA certified barriers)
Maximum output voltage (Voc) ≤ 30 V
Maximum output current (Isc) ≤ 165 mA
Maximum output power (Pmax) ≤ 0.9 W
Note 3. Installation
• All wiring shall comply with Canadian Electrical
Code Part I and Local Electrical Codes.
• The instrument modification or parts replacement
by other than authorized representative of
Yokogawa Electric Corporation and Yokogawa
Corporation of America is prohibited and will void
Canadian Standards Intrinsically safe and
nonincendive Certification.
Nonhazardous Location
Supply
–
Safety Barrier
+
+
–
–
General
Purpose
Equipment
+
–
[Nonincendive]
Hazardous Location
Nonhazardous Location
Class I, II, Division 2,
Groups A, B, C, D, E, F, G
Class III, Division 1.
General
Purpose
Equipment
EJA Series Pressure
Transmitters
+
Supply
+
–
–
Not Use
Safety Barrier
F0204.EPS
b. CSA Explosionproof Type
Caution for CSA explosionproof type.
Note 1. Model EJA Series differential, gauge, and
absolute pressure transmitters with
optional code /CF1 are applicable for use
in hazardous locations:
Certificate: 1089598
• Applicable Standard: C22.2 No.0, No.0.4, No.25,
No.30, No.94, No.142
• Explosionproof for Class I, Division 1, Groups B,
C and D.
• Dust-ignitionproof for Class II/III, Division 1,
Groups E, F and G.
• Encl “Type 4X”
• Temperature Class: T6, T5, and T4
• Process Temperature: 85°C (T6), 100°C (T5), and
120°C (T4)
• Ambient Temperature: –40 to 80°C
• Supply Voltage: 42 V dc max.
• Output Signal: 4 to 20 mA
Note 2. Wiring
• All wiring shall comply with Canadian Electrical
Code Part I and Local Electrical Codes.
• In hazardous location, wiring shall be in conduit as
shown in the figure.
CAUTION: SEAL ALL CONDUITS
WITHIN 50 cm OF THE ENCLOSURE.
UN SCELLEMENT DOIT ÊTRE
INSTALLÉ À MOINS DE 50 cm DU
BÎTIER.
• When installed in Division 2, “SEALS NOT
REQUIRED.”
2-5
IM 01C21C01-01E
2. HANDLING CAUTIONS
Note 3. Operation
• Keep the “CAUTION” label attached to the
transmitter.
CAUTION: OPEN CIRCUIT BEFORE
REMOVING COVER.
OUVRIR LE CIRCUIT AVANT
D´NLEVER LE COUVERCLE.
• Take care not to generate mechanical sparking
when accessing to the instrument and peripheral
devices in a hazardous location.
Note 4. Maintenance and Repair
• The instrument modification or parts replacement
by other than authorized representative of
Yokogawa Electric Corporation and Yokogawa
Corporation of America is prohibited and will void
Canadian Standards Explosionproof Certification.
Non-Hazardous Hazardous Locations Division 1
Locations
Non-hazardous
Location
Equipment
42 V DC Max.
4 to 20 mA DC
Signal
50 cm Max.
Sealing Fitting
Conduit
EJA Series
Non-Hazardous Hazardous Locations Division 2
Locations
Non-hazardous
Location
Equipment
42 V DC Max.
4 to 20 mA DC
Signal
Sealing Fitting
EJA Series
F0205.EPS
c. CSA Intrinsically Safe Type/CSA
Explosionproof Type
Model EJA Series pressure transmitters with
optional code /CU1 can be selected the type of
protection (CSA Intrinsically Safe or CSA
Explosionproof) for use in hazardous locations.
Note 1. For the installation of this transmitter,
once a particular type of protection is
selected, any other type of protection
cannot be used. The installation must be
in accordance with the description about
the type of protection in this instruction
manual.
Note 2. In order to avoid confusion, unnecessary
marking is crossed out on the label other
than the selected type of protection when
the transmitter is installed.
2.9.3 IECEx Certification
Model EJA Series differential, gauge, and
absolute pressure transmitters with
optional code /SU2 can be selected the type of
protection (IECEx Intrinsically Safe/type n or
flameproof) for use in hazardous locations.
Note 1. For the installation of this transmitter,
once a particular type of protection is
selected, any other type of protection
cannot be used. The installation must be
in accordance with the description about
the type of protection in this instruction
manual.
Note 2. In order to avoid confusion, unnecessary
marking is crossed out on the label other
than the selected type of protection when
the transmitter is installed.
a. IECEx Intrinsically Safe Type / type n
Caution for IECEx Intrinsically safe and type n.
Note 1. Model EJA Series differential, gauge, and
absolute pressure transmitters with
optional code /SU2 are applicable for use
in hazardous locations.
• No. IECEx KEM 06.0007X
• Applicable Standard: IEC 60079-0:2004,
IEC 60079-11:1999, IEC 60079-15:2005,
IEC 60079-26:2004
• Type of Protection and Marking Code:
Ex ia IIC T4, Ex nL IIC T4
• Ambient Temperature :–40 to 60°C
• Max. Process Temp.: 120°C
• Enclosure: IP67
Note 2. Entity Parameters
• Intrinsically safe ratings are as follows:
Maximum Input Voltage (Ui) = 30 V
Maximum Input Current (Ii) = 165 mA
Maximum Input Power (Pi) = 0.9 W
Maximum Internal Capacitance (Ci) = 22.5 nF
Maximum Internal Inductance (Li) = 730 µH
• Type "n" ratings are as follows:
Maximum Input Voltage (Ui) = 30 V
Maximum Internal Capacitance (Ci) = 22.5 nF
Maximum Internal Inductance (Li) = 730 µH
• Installation Requirements
Uo ≤ Ui, Io ≤ Ii, Po ≤ Pi,
Co ≥ Ci + Ccable, Lo ≥ Li + Lcable
Uo, Io, Po, Co, and Lo are parameters of
barrier.
Note 3. Installation
• In any safety barreir used output current must be
limited by a resistor 'R' such that Io=Uo/R.
• The safety barrier must be IECEx certified.
2-6
IM 01C21C01-01E
2. HANDLING CAUTIONS
• Input voltage of the safety barrier must be less than
250 Vrms/Vdc.
• The instrument modification or parts replacement
by other than authorized representative of
Yokogawa Electric Corporation and will void
IECEx Intrinsically safe and type n certification.
• The cable entry devices and blanking elements for
type n shall be of a certified type providing a level
of ingress protection of at least IP54, suitable for
the conditions of use and correctly installed.
• Electrical Connection:
The type of electrical connection is stamped near
the electrical connection port according to the
following marking.
T0202.EPS
Location of the marking
F0210.EPS
Note 4. Operation
• WARNING:
WHEN AMBIENT TEMPERATURE ≥ 55°C,
USE THE HEAT-RESISTING CABLES ≥ 90°C.
Note 5. Special Conditions for Safe Use
• WARNING:
IN THE CASE WHERE THE ENCLOSURE OF
THE PRESSURE TRANSMITTER IS MADE OF
ALUMINUM, IF IT IS MOUNTED IN AN AREA
WHERE THE USE OF ZONE 0 IS REQUIRED,
IT MUST BE INSTALLED SUCH, THAT, EVEN
IN THE EVENT OF RARE INCIDENTS, IGNITION SOURCES DUE TO IMPACT AND
FRICTION SPARKS ARE EXCLUDED.
[Intrinsically Safe]
Hazardous Location
Nonhazardous Location
Group I/IIC, Zone 0
EJA Series Pressure
Transmitters
+
Supply
–
IECEx certified
Safety Barrier
+
+
–
–
General
Purpose
Equipment
+
–
F0211.EPS
[type n]
Hazardous Location
Nonhazardous Location
Group IIC, Zone 2
IECEx Certified
Equipment [nL]
EJA Series Pressure
Transmitters
+
Supply
+
–
–
Not Use
Safety Barrier
F0212.EPS
b. IECEx Flameproof Type
Caution for IECEx flameproof type.
Note 1. Model EJA Series differential, gauge, and
absolute pressure transmitters with
optional code /SU2 are applicable for use
in hazardous locations:
• No. IECEx KEM 06.0005
• Applicable Standard: IEC60079-0:2004,
IEC60079-1:2003
• Type of Protection and Marking Code:
Ex d IIC T6...T4
• Enclosure: IP67
• Maximum Process Temperature: 120°C (T4),
100°C (T5), 85°C (T6)
• Ambient Temperature: –40 to 75°C (T4), –40 to
80°C (T5), –40 to 75°C (T6)
• Supply Voltage: 42 V dc max.
• Output Signal: 4 to 20 mA dc
Note 2. Wiring
• In hazardous locations, the cable entry devices shall
be of a certified flameproof type, suitable for the
conditions of use and correctly installed.
• Unused apertures shall be closed with suitable
flameproof certified blanking elements. (The plug
attached is certificated as the flame proof IP67 as a
part of this apparatus.)
• In case of ANSI 1/2 NPT plug, ANSI hexagonal
wrench should be applied to screw in.
Note 3. Operation
• WARNING:
AFTER DE-ENERGIZING, DELAY 10 MINUTES
BEFORE OPENING.
• WARNING:
WHEN AMBIENT TEMPERATURE ≥ 70°C,
USE THE HEAT-RESISTING CABLES ≥ 90°C.
• Take care not to generate mechanical sparking
when accessing to the instrument and peripheral
devices in a hazardous location.
Note 4. Maintenance and Repair
• The instrument modification or parts replacement
by other than authorized representative of
Yokogawa Electric Corporation is prohibited and
will void IECEx Certification.
2-7
IM 01C21C01-01E
2. HANDLING CAUTIONS
2.9.4 CENELEC ATEX (KEMA)
Certification
[Installation Diagram]
Hazardous Location
(1) Technical Data
Transmitter
a. CENELEC ATEX (KEMA) Intrinsically Safe
Type
Caution for CENELEC ATEX (KEMA) Intrinsically safe type.
Note 1. Model EJA Series differential, gauge, and
absolute pressure transmitters with
optional code /KS2 for potentially explosive atmospheres:
• No. KEMA 02ATEX1030 X
• Applicable Standard: EN50014:1997,
EN50020:1994, EN50284:1999
• Type of Protection and Marking code:
EEx ia IIC T4
• Temperature Class: T4
• Enclosure: IP67
• Process Temperature: 120°C max.
• Ambient Temperature: –40 to 60°C
Note 2. Electrical Data
• In type of explosion protection intrinsic safety EEx
ia IIC only for connection to a certified intrinsically
safe circuit with following maximum values:
Ui = 30 V
Ii = 165 mA
Pi = 0.9 W
Effective internal capacitance; Ci = 22.5 nF
Effective internal inductance; Li = 730 µH
Note 3. Installation
• All wiring shall comply with local installation
requirements. (Refer to the installation diagram)
Note 4. Maintenance and Repair
• The instrument modification or parts replacement
by other than authorized representative of
Yokogawa Electric Corporation is prohibited and
will void KEMA Intrinsically safe Certification.
Note 5. Special Conditions for Safe Use
• In the case where the enclosure of the Pressure
Transmitter is made of aluminium, if it is mounted
in an area where the use of category 1 G apparatus
is required, it must be installed such, that, even in
the event of rare incidents, ignition sources due to
impact and friction sparks are excluded.
Nonhazardous Location
+
+
–
–
Safety Barrier *1
Supply
F0208.EPS
*1: In any safety barriers used the output current must be limited
by a resistor “R” such that Imaxout-Uz/R.
b. CENELEC ATEX (KEMA) Flameproof Type
Caution for CENELEC ATEX (KEMA) flameproof
type.
Note 1. Model EJA Series differential, gauge, and
absolute pressure transmitters with
optional code /KF2 for potentially explosive atmospheres:
• No. KEMA 02ATEX2148
• Applicable Standard: EN50014:1997,
EN50018:2000
• Type of ProteATEXction and Marking Code: EEx
d IIC T6···T4
• Temperature Class: T6, T5, and T4
• Enclosure: IP67
• Maximum Process Temperature:
85°C (T6), 100°C (T5), and 120°C (T4)
• Ambient Temperature: T4 and T6; –40 to 75°C,
T5; –40 to 80°C
Note 2. Electrical Data
• Supply voltage: 42 V dc max.
• Output signal: 4 to 20 mA
Note 3. Installation
• All wiring shall comply with local installation
requirement.
• The cable entry devices shall be of a certified
flameproof type, suitable for the conditions of use.
Note 4. Operation
• Keep the “CAUTION” label to the transmitter.
CAUTION: AFTER DE-ENERGIZING,
DELAY 10 MINUTES BEFORE OPENING. WHEN THE AMBIENT
TEMP.70°C, USE HEAT-RESISTING
CABLES90°C.
• Take care not to generate mechanical sparking
when accessing to the instrument and peripheral
devices in a hazardous location.
Note 5. Maintenance and Repair
• The instrument modification or parts replacement
by other than authorized representative of
Yokogawa Electric Corporation is prohibited and
will void KEMA Flameproof Certification.
2-8
IM 01C21C01-01E
2. HANDLING CAUTIONS
c. CENELEC ATEX (KEMA) Intrinsically Safe
Type/CENELEC ATEX (KEMA) Flameproof
Type/ CENELEC ATEX Type n
Model EJA-A Series pressure transmitters with
optional code /KU2 can be selected the type of
protection CENELEC ATEX (KEMA) Intrinsically
Safe, Flameproof or CENELEC ATEX Type n
for use in hazardous locations.
Note 1. For the installation of this transmitter,
once a particular type of protection is selected,
any other type of protection cannot be used.
The installation must be in accordance with the
description about the type of protection in this
user’s manual.
Note 2. In order to avoid confusion, unnecessary
marking is crossed out on the label other than
the selected type of protection when the
transmitter is installed.
CENELEC ATEX Type of Protection “n”
WARNING
When using a power supply not having a nonincendive circuit, please pay attention not to
ignite in the surrounding flammable atmosphere.
In such a case, we recommend using wiring
metal conduit in order to prevent the ignition.
• Applicable Standard: EN60079-15
• Referential Standard: IEC60079-0, IEC60079-11
• Type of Protection and Marking Code:
Ex nL IIC T4
• Temperature Class: T4
• Enclosure: IP67
• Process Temperature: 120°C max.
• Ambient Temperature: –40 to 60°C
Note 1. Electrical Data
Ui = 30 V
Effective internal capacitance; Ci = 22.5 nF
Effective internal inductance; Li = 730 µH
Note 2. Installation
• All wiring shall comply with local installation
requirements. (refer to the installation diagram)
[Installation Diagram]
Hazardous Location
(Zone 2 only)
Transmitter
Nonhazardous Location
+
+
–
–
Supply
Power Supply
F0209.EPS
Ratings of the Power Supply as follows;
Maximum Voltage: 30 V
CENELEC ATEX Type of Protection “Dust”
• Applicable Standard: EN50281-1-1:1997
• Type of Protection and Marking Code: II 1D
• Maximum Surface Temperature:
T65°C (Tamb.: 40°C), T85°C (Tamb.: 60°C), and
T105°C (Tamb.: 80°C)
Note 1. Installation instructions
The cable entry devices and blanking elements
shall be of a certificated type providing a level
of ingress protection of at least IP6x, suitable
for the conditions of use and correctly installed.
(2) Electrical Connection
The type of electrical connection is stamped near
the electrical connection port according to the
following marking.
Location of the marking
F0200.EPS
(3) Installation
WARNING
• All wiring shall comply with local installation
requirement and local electrical code.
• There is no need of the conduit seal for both of
Division 1 and Division 2 hazardous locations
because this product is sealed at factory.
• In case of ANSI 1/2 NPT plug, ANSI hexagonal
wrench should be applied to screw in.
Note 3. Maintenance and Repair
• The instrument modification or parts replacement
by other than authorized representative of
Yokogawa Electric Corporation is prohibited and
will void Type of Protection “n”.
2-9
IM 01C21C01-01E
2. HANDLING CAUTIONS
(4) Operation
WARNING
• OPEN CIRCUIT BEFORE REMOVING
COVER. INSTALL IN ACCORDANCE WITH
THIS USER’S MANUAL
• Take care not to generate mechanical sparking
when access to the instrument and peripheral
devices in hazardous locations.
(5) Maintenance and Repair
MWP: Maximum working pressure.
CAL RNG: Specified calibration range.
DISP MODE: Specified display mode.
OUTPUT MODE: Specified output mode.
NO.: Serial number and year of production*1.
TOKYO 180-8750 JAPAN:
The manufacturer name and the address*2.
*1: The third figure from the last shows the last one
figure of the year of production. For example, the
production year of the product engraved in “NO.”
column on the name plate as follows is 2001.
12A819857
WARNING
The instrument modification or parts replacement
by other than authorized Representative of
Yokogawa Electric Corporation is prohibited and
will void the certification.
132
The year 2001
*2: “180-8750” is a zip code which represents the
following address.
2-9-32 Nakacho, Musashino-shi, Tokyo Japan
(6) Name Plate
Name plate
2.10 EMC Conformity Standards
EN61326-1 Class A, Table 2 (For use in industrial
locations)
EN61326-2-3
: Refer to USER'S MANUAL
Tag plate for flameproof type
CAUTION
This instrument is a Class A product, and it is
designed for use in the industrial environment.
Please use this instrument in the industrial
environment only.
Tag plate for intrinsically safe type
NOTE
YOKOGAWA recommends customer to apply
the Metal Conduit Wiring or to use the twisted
pair Shield Cable for signal wiring to conform the
requirement of EMC Regulation, when customer
installs the EJA Series Transmitters to the plant.
Tag plate for type n protection
Tag plate for flameproof, intrinsically safe type,
type n protection, and Dust
D
2.11 PED (Pressure Equipment
Directive)
T65⬚C (Tamb.: 40⬚C), T85⬚C (Tamb.: 60⬚C),
and T105⬚C (Tamb.: 80⬚C)
F0298.EPS
MODEL: Specified model code.
STYLE: Style code.
SUFFIX: Specified suffix code.
SUPPLY: Supply voltage.
OUTPUT: Output signal.
(1) General
• EJA series of pressure transmitters are categorized
as pressure accessories under the vessel section of
this directive 97/23/EC, which corresponds to
Article 3, Paragraph 3 of PED, denoted as Sound
Engineering Practice (SEP).
2-10
IM 01C21C01-01E
2. HANDLING CAUTIONS
• EJA130A, EJA440A, EJA510A, and EJA530A can
be used above 200 bar and therefore considered as
a part of a pressure retaining vessel where category
lll, Module H applies. These models with option
code /PE3 conform to that category.
(3) Operation
CAUTION
• The temperature and pressure of fluid should
be applied under the normal operating condition.
• The ambient temperature should be applied
under the normal operating condition.
• Please pay attention to prevent the excessive
pressure like water hammer, etc. When water
hammer is to be occurred, please take measures to prevent the pressure from exceeding
PS by setting the safety valve, etc. at the
system and the like.
• When external fire is to be occurred, please
take safety measures at the device or system
not to influence the transmitters.
(2) Technical Data
• Models without /PE3
Article 3, Paragraph 3 of PED, denoted as Sound
Engineering Practice (SEP) .
• Models with /PE3
Module: H
Type of Equipment: Pressure Accessory - Vessel
Type of Fluid: Liquid and Gas
Group of Fluid: 1 and 2
EJA110A
160
0.01
1.6
EJA120A
0.5
0.01
0.005
EJA130A
420
0.01
4.2
Category*2
Article 3, paragraph 3
(SEP)
Article 3, paragraph 3
(SEP)
Article 3, paragraph 3
(SEP)
EJA130A
With code /PE3
420
0.01
4.2
III
EJA310A
160
0.01
1.6
EJA430A
160
0.01
1.6
EJA440A
500
0.01
50
EJA440A
With code /PE3
500
0.01
50
III
Model
PS(bar)*1 V(L) PS-V(bar-L)
Article 3, paragraph 3
(SEP)
Article 3, paragraph 3
(SEP)
Article 3, paragraph 3
(SEP)
EJA510A
500
0.01
50
Article 3, paragraph 3
(SEP)
EJA510A
With code /PE3
500
0.01
50
III
EJA530A
500
0.01
50
Article 3, paragraph 3
(SEP)
EJA530A
With code /PE3
500
0.01
50
III
*1: PS is maximum allowable pressure for vessel itself.
*2: Referred to Table 1 covered by ANNEX II of EC Directive
on Pressure Equipment Directive 97/23/EC
T0299.EPS
2.12 Low Voltage Directive
Applicable standard : EN61010-1
(1) Pollution Degree 2
"Pollution degree" describes the degree to which a
soild, liquid, or gas which deteriorates dielectric
strength or surface resistivity is adhering. " 2 "
applies to normal indoor atmosphere. Normally,
only non-conductive pollution occurs. Occasionally,
however, temporary conductivity caused by
condenstaion must be expected.
(2) Installation Category I
"Overvoltage category(Installation category)"
describes a number which defines a transient
overvoltage condition. It implies the regulattion for
impulse withstand voltage. " I " applies to electrical
equipment which is supplied from the circuit when
appropriate transient overvoltage control means
(interfaces) are provided.
2-11
IM 01C21C01-01E
3. COMPONENT NAMES
3.
COMPONENT NAMES
Terminal box cover
Tramsmitter sedtion
Conduit
connection
External indicator
conduit connection (Note 1)
CPU assembly
Zero-adjustment screw
Integral
indicator (Note 1)
Mounting screw
Setting pin
(CN4)
Process connection
(low pressure side)
Range-setting
switch (Note 1)
(See Subsection 7.6)
Amplifier Cover
Setting pin (CN4)
position (Note 2)
Cover flange
Process connector
(Note 1)
Burn - out
direction
Output at
burn - out
HIGH
110% or
higher
LOW
-5% or
lower
H
L
H
L
Pressure-detector section
F0301.EPS
Note 1: See Subsection 10.2, “Model and Suffix Codes,” for
details.
Note 2: Insert the pin (CN4) as shown in the figure above to
set the burn-out direction. The pin is set to the H side
for delivery (unless option code /C1 is specified in the
order).
The setting can be confirmed by calling up parameter
D52 using the BRAIN TERMINAL. Refer to Subsection
8.3.3 (11).
Figure 3.1 Component Names
Table 3.1 Display Symbol
Display Symbol
Meaning of Display Symbol
The output signal being zero-adjusted is increasing.
The output signal being zero-adjusted is decreasing.
%, kPa, Pa, MPa, kgf/cm2, gf/cm2, mbar, bar,
atm, mmHg, mmH2O, inH2O, inHg, ftH2O, psi, Torr
Select one of these sixteen available engineering units for the display.
T0301.EPS
3-1
IM 01C21C01-01E
4. INSTALLATION
4.
INSTALLATION
4.1 Precautions
IMPORTANT
Please use a gasket which has a bigger inside
diameter than that of gasket facing (ød) on
diaphragm seal. In case a gasket which has a
smaller inside diameter than that of gasket
facing is used, it may cause an error as the
gasket prevents diaphragm from working correctly. (Refer to Subsection 10.4 ‘Dimensions’)
Before installing the transmitter, read the cautionary
notes in Section 2.4, “Selecting the Installation
Location.” For additional information on the ambient
conditions allowed at the installation location, refer to
Subsection 10.1 “Standard Specifications.”
IMPORTANT
• When welding piping during construction, take
care not to allow welding currents to flow
through the transmitter.
• Do not step on this instrument after installation.
• Never loosen the four screws securing the
cover flanges (if the seal liquid leaks, the
transmitter cannot be used).
4.2 Mounting
4.3 Rotating Transmitter Section
The DPharp transmitter section can be rotated in 90°
segments.
(1) Remove the two Allen screws that fasten the
transmitter section and pressure-detector section,
using the Allen wrench supplied with the transmitter.
(2) Rotate the transmitter section slowly in 90° segments.
(3) Tighten the two Allen screws.
The transmitter is mounted on a process using its highpressure side flange as shown in Figure 4.1. The
customer should prepare the mating flange, gasket, stud
bolts and nuts.
IMPORTANT
Do not rotate the transmitter section more than
180°.
Gasket
Transmitter section
Rotate 90° or 180° segments
Stud bolt
Nut
Figure 4.1
Conduit connection
F0401.EPS
Transmitter Mounting
Zero-adjustment screw
Pressure-detector section
F0402.EPS
Figure 4.2 Rotating Transmitter Section
4-1
IM 01C21C01-01E
4. INSTALLATION
4.4 Changing the Direction of
Integral Indicator
4.5 Affixing the Teflon Film
IMPORTANT
IMPORTANT
The FEP Teflon option includes a teflon film and
fluorinated oil. Before mounting the transmitter
to the process flange, affix the teflon film as
follows:
1) Position the diaphragm so that the diaphragm
is in a upward position.
2) Pour the fluorinated oil on the diaphragm and
gasket area covering it completely and evenly.
Be careful not to scratch the diaphragm or
change the its shape.
3) Affix the teflon film over the diaphragm and
gasket area.
4) Next, carefully inspect the cover and try to
identify any entrapped air between the diaphragm and the teflon film. The air must be
removed to ensure accuracy. If air pockets are
present, use your fingers to remove the air by
starting at the center of the diaphragm and
work your way out.
5) Place the gasket with the teflon film and affix
to the process flange.
Always turn OFF power, release pressure and
remove a transmitter to non-hazardous area
before disassembling and reassmbling an
indicator.
An integral indicator can be installed in the following
three directions. Follow the instructions in section 9.4
for removing and attaching the integral indicator.
F0404.EPS
Figure 4.3
Integral Indicator Direction
Teflon film
Fluorinated oil
[PART No. : F9145YN]
Diaphragm
Gasket area
PART No.
Prosess Flange size
F9347XA
3 inch (80mm)
F9347YD
2 inch (50mm)
F0403.EPS
Figure 4.4 Affixing the Teflon Film
4-2
IM 01C21C01-01E
5. INSTALLING IMPULSE PIPING
5.
INSTALLING IMPULSE PIPING
5.1 Impulse Piping Installation
Precautions
(2) Tightening the Process Connector Mounting Bolts
After connecting the impulse piping, tighten the
process connector mounting bolts uniformly.
The impulse piping that connects the process outputs to
the transmitter must convey the process pressure
accurately. If, for example, gas collects in a liquidfilled impulse piping, or the drain of a gas-filled
impulse piping becomes plugged, the impulse piping
will not convey the pressure accurately. Since this will
cause errors in the measurement output, select the
proper piping method for the process fluid (gas, liquid,
or steam). Pay careful attention to the following points
when routing the impulse piping and connecting the
impulse piping to the transmitter.
(3) Removing the Impulse Piping Connecting
Port Dustproof Cap
The impulse piping connecting port of the transmitter
is covered with a plastic cap to exclude dust. This cap
must be removed before connecting the piping. (Be
careful not to damage the threads when removing this
cap. Never insert a screwdriver or other tool between
the cap and port threads to remove the cap.)
5.1.2 Routing the Impulse Piping
5.1.1 Connecting Impulse Piping to the
Transmitter
(1) Impulse Piping Slope
The impulse piping must be routed with only an
upward or downward slope. Even for horizontal
routing, the impulse piping should have a slope of at
least 1/10 to prevent condensate (or gases) from
accumulating in the pipes.
(1) Check the High and Low Pressure Connections on the Transmitter (Figure 5.1)
Symbols “H” and “L” are shown on a capsule assembly to indicate high and low pressure side. For liquid
level measurement in an open tank, the ‘L’ (low
pressure) side is used to refer atmosphere. For a
closed tank, connect the impulse line to the low
pressure side of the transmitter. This will refer the
pressure in the tank.
(2) Preventing Freezing
If there is any risk that the process fluid in the impulse
piping or transmitter could freeze, use a steam jacket or
heater to maintain the temperature of the fluid.
“ H ” and “ L ” are shown
NOTE
Low pressure
connection
After completing the connections, close the valves
on the process pressure taps (main valves), the
valves at the transmitter (stop valves), and the
impulse piping drain valves, so that condensate,
sediment, dust and other extraneous material
cannot enter the impulse piping.
Process connector
Bolt
F0501.EPS
Figure 5.1
“H” and “L” Symbols on a Capsule Assembly
5-1
IM 01C21C01-01E
5. INSTALLING IMPULSE PIPING
5.2 Impulse Piping Connection
Examples
Figure 5.2 shows examples of typical impulse piping
connections. Before connecting the transmitter to the
process, study the transmitter installation location, the
process piping layout, and the characteristics of the
process fluid (corrosiveness, toxicity, flammability,
etc.), etc. and make appropriate changes and additions
to the connection configurations.
Open Tank
Pipe (opened to atmosphere
at low pressure side)
Closed Tank
Tap valve
Union or flange
Vent plug
Tee
Drain valve
Drain plug
F0502.EPS
Figure 5.2 Impulse Piping Connection Examples
5-2
IM 01C21C01-01E
6. WIRING
6.
WIRING
6.1 Wiring Precautions
IMPORTANT
• Lay wiring as far as possible from electrical
noise sources such as large capacity transformers, motors, and power supplies.
• Remove electrical connection dust cap before
wiring.
• All threaded parts must be treated with waterproofing sealant. (A non-hardening silicone
group sealant is recommended.)
• To prevent noise pickup, do not pass signal
and power cables through the same ducts.
• Explosion-protected instruments must be wired
in accordance with specific requirements (and,
in certain countries, legal regulations) in order
to preserve the effectiveness of their explosionprotected features.
• The terminal box cover is locked by an Allen
head bolt (a shrouding bolt) on CENELEC and
IECEx flameproof type transmitters. When the
shrouding bolt is driven clockwise by an Allen
wrench, it is going in and cover lock is released, and then the cover can be opened by
hand. See Subsection 9.4 “Disassembly and
Reassembly” for details.
6.3 Connections of External
Wiring to Terminal Box
6.3.1 Power Supply Wiring Connection
Connect the power supply wiring to the SUPPLY +
and – terminals.
Transmitter terminal box
+
Power supply
–
F0601.EPS
Figure 6.3.1 Power Supply Wiring Connection
6.3.2 External Indicator Connection
Connect wiring for external indicators to the CHECK +
and – terminals.
(Note) Use a external indicator whose internal resistance is 10 Ω or
less.
External indicator
Power supply
+
–
Transmitter terminal box
6.2 Selecting the Wiring Materials
(a) Use stranded leadwires or cables which are the
same as or better than 600 V grade PVC insulated
wire (JIS C3307) or equivalent.
(b) Use shielded wires in areas that are susceptible to
electrical noise.
(c) In areas with higher or lower ambient temperatures,
use appropriate wires or cables.
(d) In environment where oils, solvents, corrosive gases
or liquids may be present, use wires or cables that
are resistant to such substances.
(e) It is recommended that crimp-on solderless terminal
lugs (for 4 mm screws) with insulating sleeves be
used for leadwire ends.
F0602.EPS
Figure 6.3.2 External Indicator Connection
6.3.3 BRAIN TERMINAL BT200 Connection
Connect the BT200 to the SUPPLY + and – terminals
(Use hooks). The communication line requires a
reception resistor of 250 to 600 Ω in series.
Transmitter terminal box
+
Power supply
–
BT200
Ignore the polarity
since the BT200 is
AC-coupled to the
terminal box.
F0603.EPS
Figure 6.3.3 BT200 Connection
6-1
IM 01C21C01-01E
6. WIRING
(2) Intrinsically Safe Type
For intrinsically safe type, a safety barrier must be
included in the loop.
6.3.4 Check Meter Connection
Connect the check meter to the CHECK + and –
terminals (use hooks).
• A 4 to 20 mA DC output signal from the CHECK +
and – terminals.
Hazardous Location
(Note) Use a check meter whose internal resistance is 10 Ω or less.
Transmitter terminal box
Nonhazardous Location
Distributor
(Power supply unit)
Power supply
+
Receiver
instrument
–
+
Check meter
Transmitter terminal box
F0604.EPS
Figure 6.3.4 Check Meter Connection
Safety barrier
Figure 6.4.1b Connection between Transmitter and
Distributor
6.4 Wiring
6.4.2 Wiring Installation
6.4.1 Loop Configuration
Since the DPharp uses a two-wire transmission system,
signal wiring is also used as power wiring.
DC power is required for the transmitter loop. The
transmitter and distributor are connected as shown
below.
For details of the power supply voltage and load
resistance, see Section 6.6; for communications line
requirements, see Subsection 8.1.2.
(1) General-use Type and Intrinsically Safe
Type
Make cable wiring using metallic conduit or waterproof glands.
• Apply a non-hardening sealant to the terminal box
connection port and to the threads on the flexible
metal conduit for waterproofing.
(1) General-use Type and Flameproof Type
Hazardous Location
Transmitter terminal box
F0606.EPS
Flexible metal conduit
Nonhazardous Location
Wiring metal
conduit
Distributor
(Power supply unit)
Apply a non-hardening
sealant to the threads for
waterproofing.
Tee
Drain plug
F0607.EPS
+
Receiver
instrument
Figure 6.4.2a Typical Wiring Using Flexible Metal Conduit
F0605.EPS
Figure 6.4.1a Connection between Transmitter and
Distributor
6-2
IM 01C21C01-01E
6. WIRING
(2) Flameproof Type
Wire cables through a flameproof packing adapter, or
using a flameproof metal conduit.
䊏 Wiring cable through flameproof packing adapter.
• Apply a nonhardening sealant to the terminal box
connection port and to the threads on the flameproof
packing adapter for waterproofing.
6.5 Grounding
Grounding is always required for the proper operation
of transmitters. Follow the domestic electrical requirements as regulated in each country. For a transmitter
with built-in lightning protector, grounding should
satisfy ground resistance of 10⍀ or less.
Ground terminals are located on the inside and outside
of the terminal box. Either of these terminals may be
used.
Flameproof packing adapter
Transmitter terminal box
Flexible metal conduit
Wiring metal
conduit
Apply a non-hardening
sealant to the threads for
waterproofing.
Ground terminal
(Inside)
Tee
Drain plug
F0608.EPS
Figure 6.4.2b Typical Cable Wiring Using Flameproof
Packing Adapter
䊏 Flameproof metal conduit wiring
• A seal fitting must be installed near the terminal box
connection port for a sealed construction.
• Apply a non-hardening sealant to the threads of the
terminal box connection port, flexible metal conduit
and seal fitting for waterproofing.
Ground terminal
(Outside)
Figure 6.5 Ground Terminals
6.6 Power Supply Voltage and
Load Resistance
Gas sealing device
Non-hazardous area
Flameproof flexible
metal conduit
When configuring the loop, make sure that the external
load resistance is within the range in the figure below.
Hazardous area
Flameproof
heavy-gauge
steel conduit
Apply a non-hardening
sealant to the threads of
these fittings for
waterproofing
(Note) In case of an intrinsically safe transmitter, external load
resistance includes safety barrier resistance.
600
Tee
Drain plug
;;
F0610.EPS
Seal fitting
After wiring, impregnate the fitting
with a compound to seal tubing.
External
load
resistance
R (Ω)
F0609.EPS
Figure 6.4.2c Typical Wiring Using Flameproof Metal
Conduit
250
R=
0
E–10.5
0.0236
10.5
Communication
applicable range
BRAIN and HART
16.4
24.7
42
Power supply voltage E (V DC)
F0611.EPS
Figure 6.6 Relationship between Power Supply Voltage
and External Load Resistance
6-3
IM 01C21C01-01E
7. OPERATION
7.
OPERATION
Confirming that Transmitter is Operating
Properly
Using the BT200
• If the wiring system is faulty, ‘communication error’
appears on the display.
• If the transmitter is faulty, ‘SELF CHECK ERROR’
appears on the display.
7.1 Preparation for Starting
Operation
The Model EJA210A and EJA220A flange mounted
differential pressure transmitter measures the levels or
densities of liquids. This section describes the operation procedure for the EJA210A as shown in Figure 7.1
when measuring a liquid level in an open tank.
PARAM
C60:SELF CHECK
ERROR
(a) Confirm that there is no leak in the connecting part
of the transmitter mounting flange.
Remove the plastic dust cap placed in the process
connector (low pressure side).
(b) Turn ON power and connect the BT200.
Open the terminal box cover and connect the
BT200 to the SUPPLY + and – terminals.
(c) Using the BT200, confirm that the transmitter is
operating properly. Check parameter values or
change the setpoints as necessary.
For BT200 operating procedures, see Chapter 8. If
the transmitter is equipped with an integral indicator, its indication can be used to confirm that the
transmitter is operating properly.
communication error
DATA
Communication error
(Faulty wiring)
DIAG
PRNT
ESC
Self-diagnostic error
(Faulty transmitter)
F0702.EPS
Using the integral indicator
• If the wiring system is faulty, the display stays blank.
• If the transmitter is faulty, an error code will appear
on the display according to the nature of the error.
Open tank
Self-diagnostic error on
the integral indicator
(Faulty transmitter)
F0703.EPS
NOTE
If any of the error indications above appears on
the display of the integral indicator or BT200,
refer to Subsection 8.5.2 for corrective action.
Verify and Change Transmitter Parameter
Setting and Values
The following parameters are the minimum settings
required for operation. The transmitter has been
shipped with these parameters. To confirm or change
the values, see Subsection 8.3.3.
F0701.EPS
Figure 7.1 Liquid Level Measurement
• Measuring range ....... See Subsection 8.3.3 (2)
• Operation mode ......... See Subsection 8.3.3 (8)
7-1
IM 01C21C01-01E
7. OPERATION
7.2.1 When you can obtain Low Range
Value from actual measured value
of 0% (0 kPa, atmospheric pressure);
7.2 Zero Point Adjustment
Adjust the zero point after operating preparation is
completed.
Using the Transmitter Zero-adjustment
Screw
Before adjusting a screw, check that the parameter
J20: EXT ZERO ADJ displays ENABLE. See
Subsection 8.3.3 (12) for the setting procedure.
IMPORTANT
Do not turn off the power to the transmitter
immediately after a zero adjustment. Powering
off within 30 seconds after a zero adjustment will
return the adjustment back to the previous
settings.
Use a slotted screwdriver to turn the zero-adjustment
screw. Turn the screw clockwise to increase the output
or counterclockwise to decrease the output. The zero
point adjustment can be made with a resolution of
0.01% of the setting range. Since the degree of zero
adjustments varies with the screw turning speed, turn
the screw slowly for fine adjustment and quickly for
coarse adjustment.
The zero point adjustment can be made in either way:
using the zero-adjustment screw of the transmitter or
the BT200 operation.
For output signal checking, display the parameter A10:
OUTPUT (%) in the BT200.
Using the BT200
Zero point can be adjusted by simple key operation of
the BT200.
BT200
Select parameter J10: ZERO ADJ, and press the
ENTER key twice. The zero point will be adjusted
automatically to the output signal 0% (4 mA DC).
Confirm that the setting value displayed for the
parameter is ‘0.0%’ before pressing the ENTER key.
See Subsection 8.3.3 (12) for BT200 operating procedures.
Output signal (%)
display
PARAM
A10:OUTPUT(%)
0.0 %
A11:ENGR OUTPUT
A20:AMP TEMP
DATA
DIAG
PRNT
ESC
Zero-adjustment Screw
SET
J10:ZERO ADJ
–0.0 %
+ 000.0
A display when parameter
J10 is selected.
Press
key
twice for 0% output 4 mA DC.
Zero-adjustment
screw
CLR
ESC
F0705.EPS
F0704.EPS
When adjusting the transmitter zero point, the liquid
level in a tank does not have to be set to the low limit
(0%) of the measuring range. In such case, match the
transmitter output signal with the actual measured
value using a glass gauge, for example.
7-2
IM 01C21C01-01E
7. OPERATION
7.2.2 When you cannot obtain Low Range
Value from actual measured value
of 0%;
IMPORTANT
• Remove the BT200 from the terminal box, and
confirm that none of the terminal screws are
loosened.
• Close the terminal box cover and the amplifier
cover. Screw each cover in tightly until it will
not turn further.
• Two covers are required to be locked on the
CENELEC and IECEx Flameproof type transmitters. An Allen head bolts (shrouding bolts)
are provided under edge of the each cover for
locking. When a shrouding bolts are driven
counterclockwise by an Allen wrench, it is
coming out and locks up a cover. (See page 93) After locking, the covers should be confirmed not to be opened by hand.
• Tighten the zero-adjustment cover mounting
screw to fix the cover in position.
Convert the actual measured value obtained by a glass
gauge into %.
[Example]
The measuring range of 0 to 2 m and the actual
measured value of 0.8 m.
Actual measured value=
0.8
x 100=40.0%
2
Using the Transmitter Zero-Adjustment Screw
Turn the screw to match the output signal to the actual
measured value in %.
Using the BT200
Select the parameter J10: ZERO ADJ. Change the
set point (%) displayed for the parameter to the actual
measured value (%), and press the ENTER key twice.
See Subsection 8.3.3 (12) for operation details.
7.4 Shutting Down Operation
Turn off the power.
A display at J10
SET
J10:ZERO ADJ
–0.0 %
+ 000.0
NOTE
CLR
Whenever shutting down the transmitter for a
long period, detach the transmitter from the tank.
ESC
Change setting to the actually
SET
J10:ZERO ADJ
–0.0 %
+ 040.0
7.5 Venting or Draining Transmitter Pressure-detector Section
measured value (40.0%).
Press
key twice
for 40% output 10.4 mA DC.
CLR
Since this transmitter is designed to be self-draining
and self-venting with vertical impulse piping connections, neither draining nor venting will be required if
the impulse piping is configured appropriately for selfdraining or self-venting operation.
ESC
F0706.EPS
7.3 Starting Operation
If condensate (or gas) collects in the transmitter
pressure-detector section, the measured pressure may
be in error. If it is not possible to configure the piping
for self-draining (or self-venting) operation, you will
need to loosen the drain (vent) screw on the transmitter
to completely drain (vent) any stagnated liquid (gas).
After completing the zero point adjustment, follow the
procedure below to start operation.
1) Confirm the operating status.
The output signal may widely fluctuate (hunting
state) due to process pressure periodic variation. In
such case, BT200 operation can dampen the transmitter output signal. Confirm the hunting state using
a receiving instrument or the integral indicator and
set the optimum damping time constant. See
Subsection 8.3.3 (3) “Damping time constant setup.”
2) After confirming the operating status, perform the
following:
However, since draining condensate or bleeding off gas
gives the pressure measurement disturbance, this
should not be done when the loop is in operation.
7-3
IM 01C21C01-01E
7. OPERATION
7.6 Setting the Range Using the
Range-setting Switch
WARNING
Since the accumulated liquid (or gas) may be
toxic or otherwise harmful, take appropriate care
to avoid contact with the body, or inhalation of
vapors.
7.5.1
With actual pressure being applied to the transmitter,
the range-setting switch (push-button) located on the
optional integral indicator plate and the external zeroadjustment screw allow users to change (re-range) the
low- and high-limit values for the measurement range
(LRV and HRV) without using BT200. However, other
changes in the display settings (scale range and
engineering unit) for the integral indicator requires
BT200.
Draining Condensate
1) Gradually open the drain plug and drain the
transmitter pressure-detector section. (See Figure
7.5.1.)
2) When all accumulated liquid is completely removed, close the drain plug.
3) Tighten the drain plug to a torque of 34 to 39 N·m.
7.5.2
Follow the procedure below to change the LRV and
HRV settings.
[Example]
Rerange LRV to 0 and HRV to 3 MPa.
Venting Gas
1) Connect the transmitter and apparatus as shown in
Figure 9.3.1 and warm up for at least five minutes.
2) Press the range-setting push-button.
The integral indicator then displays “LSET.”
3) Apply a pressure of 0 kPa (atmospheric pressure) to
the transmitter. (Note 1)
4) Turn the external zero-adjustment screw in the
desired direction. The integral indicator displays the
output signal in %. (Note 2)
5) Adjust the output signal to 0% (1 V DC) by rotating
the external zero-adjustment screw. Doing so
completes the LRV setting.
6) Press the range-setting push-button. The integral
indicator then displays “HSET.”
7) Apply a pressure of 3 MPa to the transmitter. (Note 1)
8) Turn the external zero-adjustment screw in the
desired direction. The integral indicator displays the
output signal in %. (Note 2)
9) Adjust the output signal to 100% (5 V DC) by
rotating the external zero-adjustment screw. Doing
so completes the HRV setting.
10) Press the range-setting push-button. The transmitter
then switches back to the normal operation mode
with the measurement range of 0 to 3 MPa.
1) Gradually open the vent screw to vent gas from the
transmitter pressur-detector section. (See Figure
7.5.1)
2) When the transmitter is completely vented, close
the vent screw.
3) Tighen the vent screw to a torque of 10 N·m.
Drain plug
Vent screw
When you loosen the drain plug or the vent screw, the accumulated
liquid(or gas) will be expelled in the direction of the arrow.
F0707.EPS
Figure 7.5.1 Draining/Venting the Transmitter
Note 1: Wait until the pressure inside the pressure-detector section
has stabilized before proceeding to the next step.
Note 2: If the pressure applied to the transmitter exceeds the previous
LRV (or HRV), the integral indicator may display error
number “Er.07” (In this case, the output signal percent and
“Er.07” are displayed alternately every two seconds).
Although “Er.07” is displayed, you may proceed to the next
step. However, should any other error number be displayed,
take the appropriate measure in reference to Subsection
8.5.2, “Errors and Countermeasures.”
7-4
IM 01C21C01-01E
7. OPERATION
IMPORTANT
• Do not turn off the power to the transmitter
immediately after completion of the change in
the LRV and/or HRV setting(s). Note that
powering off within thirty seconds after setting
will cause a return to the previous settings.
• Changing LRV automatically changes HRV to
the following value.
HRV = previous HRV + (new LRV – previous LRV)
• If the range-setting push-button and external
zero-adjustment screw are not touched during a
range-change operation, the transmitter automatically switches back to the normal operation
mode.
Integral indicator
Note : Use a thin bar which
has a blunt tip, e.g.,
a hexagonal wrench,
to press the rangesetting push-button
Range-setting switch
(Push-button)
Figure 7.6
F0708.EPS
Range-setting Switch
7-5
IM 01C21C01-01E
8. BRAIN TERMINAL BT200 OPERATION
8.
BRAIN TERMINAL BT200
OPERATION
The DPharp is equipped with BRAIN communications
capabilities, so that range changes, Tag No. setup,
monitoring of self-diagnostic results, and zero point
adjustment can be handled by remote control via
BT200 BRAIN TERMINAL or CENTUM CS console.
This section describes procedures for setting parameters using the BT200. For details concerning the
BT200, see IM 01C00A11-01E, “BT200 User’s
Manual.”
8.2 BT200 Operating Procedures
8.2.1 Key Layout and Screen Display
Figure 8.2.1a shows the arrangement of the operating
keys on the BT200 keypad, and Figure 8.2.1b shows
the BT200 screen component.
LCD
(21 character × 8 lines)
8.1 BT200 Operation Precautions
8.1.1 Connecting the BT200
Connection to the transmitter with the BT200 can be
made by either connecting to the BT200 connection
hooks in the transmitter terminal box or by connecting
to a relaying terminal board.
Function keys
Movement keys
ENTER key
Power ON/OFF key
Relaying
terminals
Control room
Terminal board
Alphanumeric keys
Distributor
Shift keys
F0803.EPS
Figure 8.2.1a BT200 Key Layout
F0801.EPS
Figure 8.1.1 Connecting the BT200
MENU SCREEN
8.1.2
MENU
A:DISPLAY
B:SENSOR TYPE
Conditions of Communication Line
BATTERY
Messages
Menu choices
Screen title
Cable resistance Rc
HOME
SET
ADJ
ESC
PARAMETER SCREEN
Power
supply
cc
Parameters
Load
resistance R
Cable
resistance Rc
Loop resistance = R + 2Rc
= 250 to 600 Ω
Loop capacitance = 0.22 µF max.
DPharp
PARAM
A10:OUTPUT
100.0 %
A11:ENGR. OUTPUT
1000 mmH20
A20:AMP TEMP
23 deg C
DATA
DI
AG
Function
commands
PRNT
F0804.EPS
Figure 8.2.1b BT200 Screen Component
BT200
F0802.EPS
Figure 8.1.2 Conditions of Communication Line
8-1
IM 01C21C01-01E
8. BRAIN TERMINAL BT200 OPERATION
8.2.2 Operating Key Functions
Use the function key [F1] CODE to enter symbols. The
following symbols will appear in sequence, one at a
time, at the cursor each time you press [F1] CODE:
(1) Alphanumeric Keys and Shift Keys
You can use the alphanumeric keys in conjunction with
the shift keys to enter symbols, as well as alphanumeric keys.
/ . – , + * ) ( ’ & % $ # ” !
To enter characters next to these symbols, press [ > ] to
move the cursor.
Entry
Key-in Sequence
symbol command
Alphanumeric keys
l/m
(I)
(m)
(/)
T0803.EPS
Shift keys
(2) Function Keys
The functions of the function keys depend on the
function commands on display.
F0805.EPS
a. Entering Digits, Symbols, and Spaces
Simply press the alphanumeric keys.
Entry
MENU
A:DISPLAY
B:SENSOR TYPE
Key-in Sequence
–4
0.3
1
HOME
SET
ADJ
ESC
–9
Function commands
Function keys
T0801.EPS
F0808.EPS
b. Entering Letters (A through Z)
Press an alphanumeric key following a shift key to
enter the letter shown on that side which the shift key
represents. You must press the shift key before
entering each letter.
Function Command List
Command
ADJ
Function
Displays the ADJ menu
CAPS/caps Selects uppercase or lowercase
Left-side letter on the
alphanumeric key
Right-side letter on
the alphanumeric key
CODE
F0806 .EPS
Entry
Key-in Sequence
W
IC
T0802.EPS
Use the function key [F2] CAPS to select between
uppercase and lowercase (for letters only). The case
toggles between uppercase and lowercase each time
you press [F2] CAPS.
Entering uppercase
CODE
CAPS
CLR
Erases input data or deletes all data
DATA
Updates parameter data
DEL
Deletes one character
DIAG
Calls the self-check panel
ESC
Returns to the most recent display
HOME
J. B
CLR
ESC
CODE
caps
CLR
Quits setup and returns to the previous display
OK
Proceeds to the next panel
SET
ESC
Displays the menu panel
NO
PARM
Entering lowercase
Selects symbols
Enters the parameter number setup mode
Displays the SET menu
SLOT
Returns to the slot selection panel
UTIL
Calls the utility panel
*COPY
Prints out parameters on display
*FEED
Paper feed
*LIST
Lists all parameters in the menu
*PON/POFF Automatic printout mode on or off
Entry
*PRNT
Key-in Sequence
*GO
to lower case
*STOP
Boy
(B)
(o)
Changes to the print mode
Starts printing
Cancels printing
* Available on BT200-P00 (with printer).
(y)
T0804.EPS
F0807.EPS
8-2
IM 01C21C01-01E
8. BRAIN TERMINAL BT200 OPERATION
8.2.3 Calling Up Menu Addresses Using the Operating Keys
––WELCOME––
BRAIN TERMINAL
ID: BT200
STARTUP
SCREEN check connection
push ENTER key
UTIL
The utility screen contains the
following items.
1. BT200 ID settings
2. Security code settings
3. Switching language of messages
(Japanese or English)
4. LCD contrast setting
5. Adjusting printout tone
(BT200-P00 only)
UTILITY
1.ID
2.SECURITY CODE
3.LANGUAGE SELECT
4.LCD CONTRAST
5.PRINTER ADJUST
esc
FEED
(UTIL)
INITIAL
DATA
SCREEN
PARAM
01:MODEL
EJA210A-DM
02:TAG NO.
YOKOGAWA
03:SELF CHECK
GOOD
FUNC
1.MENU
2.UPLOAD TO BT200
3.DOWNLOAD TO INST
4.PRINT ALL DATA
(ESC)
OK
HOME
(SET MENU SCREEN)
MENU
A.DISPLAY
B.SENSOR TYPE
PARAMETER
SCREEN
SETUP
SCREEN
SET
ADJ
ESC
HOME
SET
MENU
J.ADJUST
K.TEST
M.MEMO
P:RECORD
ADJ
ESC
PARAM
A60:SELF CHECK
GOOD
PARAM
C60:SELF CHECK
GOOD
PARAM
A21:CAPSULE TEMP
26.5 deg C
DATA DIAG PRNT
PARAM
C22:HIGH RANGE
100 kPa
DATA DIAG PRNT
ESC
PARAM
A10:OUTPUT(%)
50.0 %
DATA DIAG
PRNT
ESC
A11:ENGR,
OUTPUT
20.0 M
A20:AMP TEMP
24.5 deg C
DATA DIAG PRNT
ESC
CAPS
HOME
ESC
PARAM
C10:TAG NO.
YOKOGAWA
DATA DIAG
ESC
C20:PRESS
UNITPRNT
kPa
C21:LOW RANGE
0 kPa
DATA DIAG PRNT
ESC
SET
ADJ
ESC
PARAM
J60:SELF CHECK
GOOD
PARAM
J10:ZERO ADJ
0.0 %
DATA DIAG
ESC
J11:ZERO
DEV PRNT
22.2 %
J20:EXT. ZERO ADJ
ENABLE
DATA DIAG PRNT
ESC
See “BT200 Instruction Manual” for details
concerning uploading and downloading parameters
and printouts (BT200-P00).
SET
C10:TAG NO.
YOKOGAWA
YOKOGAWA
CODE
ESC
(ADJ MENU SCREEN)
MENU
C.SETTING
D.AUX SET 1
E.AUX SET 2
H:AUTO SET
MENU
SCREEN
HOME
ADJ
(ADJ)
(SET)
(HOME MENU SCREEN)
SET
CLR
ESC
F0809.EPS
8-3
IM 01C21C01-01E
8. BRAIN TERMINAL BT200 OPERATION
8.3 Setting Parameters Using the BT200
8.3.1
Parameter Summary
Instruments to which applicable:
F: Differential pressure transmitters
P: Pressure transmitters
L: Liquid level transmitters
No.
Item
01 MODEL
02 TAG NO.
EJA110A, EJA120A, and EJA130A
EJA310A, EJA430A, EJA440A, EJA510A, and EJA530A
EJA210A and EJA220A
Description
Model+capsule type
Tag number
03 SELF CHECK Self-diagnostic result
A
DISPLAY
Measured data display
A10 OUTPUT (%)
A11 ENGR.
OUTPUT
A20 AMP TEMP
A21 CAPSULE
TEMP
A30 STATIC
PRESS
A40 INPUT
Output (in %)
Output (in engineering
units)
Amplifier temperature
Capsule temperature
Static pressure
Input (indicated as the
value after zeroing)
A60 SELF CHECK Self-diagnostic
messages
B
B10
B11
B20
B21
B30
B40
SENSOR
TYPE
Sensor type
MODEL
STYLE NO.
LRL
URL
MIN SPAN
MAX STAT.P.
Model+span
Style number
Lower range-limit
Upper range-limit
Minimum span
Maximum static
pressure*6
B60 SELF CHECK Self-diagnostic
messages
C SETTING
Setting data
C10 TAG. NO.
Tag number
C20 PRESS UNIT Measurement range
units
Rewritability
D
AUX SET 1
Auxiliary setting data 1
Default Value
F P L
—
16 alphanumerics
—
GOOD/ERROR
—
—
—
Menu name
–5 to 110%*3
–19999 to 19999
—
Unit specified in D30
Unit specified in D30
—
Unit specified in D31*1
—
–32000 to 32000
—
—
—
GOOD/ERROR, CAP MODULE FAULT, AMP MODULE FAULT,
OUT OF RANGE, OUT OF SP RANGE*1, OVER TEMP (CAP),
OVER TEMP (AMP), OVER OUTPUT, OVER DISPLAY,
ILLEGAL LRV, ILLEGAL HRV, ILLEGAL SPAN, and
ZERO ADJ OVER
—
Menu name
—
16 uppercase alphanumerics
—
—
—
—
–32000 to 32000
–32000 to 32000
–32000 to 32000
—
—
—
Same as A60
—
Menu name
—
16 alphanumerics
Selected from mmH2O, mmAq,
mmWG, mmHg, Torr, Pa, hPa, kPa,
MPa, mbar, bar, gf/cm2, kgf/cm2,
inH2O, inHg, ftH2O, psi, or atm
–32000 to 32000(but within
measurement range)
–32000 to 32000(but within
measurement range)
Selected from 0.2*2, 0.5, 1.0, 2.0,
4.0, 8.0, 16.0, 32.0, or 64.0 sec.
Selected from OUT:LIN; DSP:LIN,
OUT:LIN; DSP:SQR,
OUT:SQR; DSP:SQR
Same as A60
—
Menu name
As specified when ordered.
As specified when ordered.
As specified when ordered.
As specified when ordered.
2.0 s
As specified when ordered.
If not specified,
OUT: LIN; DSP: LIN.
D10 LOW CUT
D11 LOW CUT
MODE
D15 OUT LIMIT(L)
D16 OUT LIMIT(H)
D20 DISP SELECT
Low cut
Low cut mode
0.0 to 20.0%
LINEAR/ZERO
Lower output range-limit
Upper output range-limit
Display selection
–5.0%*1
110.0%
As specified when ordered.
D21 DISP UNIT
Engineering unit for
display
Engineering range,
lower range value
Engineering range,
higher range value
Temperature setting
units
–5.0 to 110.0%
–5.0 to 110.0%
NORMAL %/USER SET,
USER & %/INP PRES, PRES & %
8 uppercase
alphanumerics
–19999 to 19999
–19999 to 19999
As specified when ordered.
deg C/deg F
deg C
D22 DISP LRV
D23 DISP HRV
D30 TEMP UNIT
Applicability
—
C21 LOW RANGE Measurement range,
lower range value
C22 HIGH
Measurement range,
RANGE
higher range value
C30 AMP
Damping time constant
DAMPING
C40 OUTPUT
Output mode and
integral indicator mode
MODE
C60 SELF CHECK Self-diagnostic
messages
Remarks
—
—
10.0%
LINEAR
As specified when ordered.
*1: Unless otherwise specified by order. When optional code /F1 is specified, substitute the value –5 with –2.5.
T0805.EPS
8-4
IM 01C21C01-01E
8. BRAIN TERMINAL BT200 OPERATION
No.
D
Item
AUX SET 1
D31 STAT. P. UNIT
Description
Auxiliary setting data 1
Auxiliary setting data 2
DFS mode
Reference temperature
sensor
Zero shift
conpensation setup
Bidirectional mode
E30 BI DIRE
MODE
E50 AUTO
Auto-recover from
RECOVER
sensor error
E60 SELF CHECK Self-diagnostic
messages
H
AUTO SET
—
Automatic setup
Automatic measurement range lower
range value setup
H11 AUTO HRV
Automatic
measurement range
higher range value
setup
H60 SELF CHECK Self-diagnostic
messages
ADJUST
Adjustment data
Automatic zero
adjustment
J11 ZERO DEV.
Manual zero
adjustment
J15 SPAN ADJ
Manual span adjustment
J20 EXT. ZERO
External zeroADJ
adjustment screw
permission
J30 OUTPUT 4mA 4mA adjustment
J31 OUTPUT 20mA 20mA adjustment
J60 SELF CHECK Self-diagnostic
messages
TEST
Tests
—
—
HOLD/HIGH/LOW, –5 to 110%*3
Same as A60
MEMO
Memo
M10
M20
M30
M40
M50
M60
M
MEMO 1
MEMO 2
MEMO 3
MEMO 4
MEMO 5
SELF CHECK
Memo
Memo
Memo
Memo
Memo
Self-diagnostic
messages
P
P10
P11
P12
P13
P60
RECORD
ERROR REC 1
ERROR REC 2
ERROR REC 3
ERROR REC 4
SELF CHECK
If not specified, NORMAL.
NORMAL
Menu name
OFF/ON*5
AMP. TEMP/CAP. TEMP*5
ON
CAP. TEMP
10.00*5
0.00
OFF/ON
OFF
OFF/ON
ON
—
Same as A60
—
Menu name
–32000 to 32000
Displays the same data as
C21.
–32000 to 32000
Displays the same data as
C22.
—
Same as A60
—
Menu name
—
—
—
—
—
—
—
—
–5 to 110.0%*3
–10.00 to 10.00%
ENABLE/INHIBIT
0.00%
0.00%
0.00%
—
–10.00 to 10.00%
–10.00 to 10.00%
Same as A60
—
Menu name
—
–5 to 110.0%*3 Displays ‘ACTIVE’
while executing
Same as A60
—
Menu name
—
8 uppercase alphanumerics
8 uppercase alphanumerics
8 uppercase alphanumerics
8 uppercase alphanumerics
8 uppercase alphanumerics
Same as A60
K10 OUTPUT in % Test output % setting
K60 SELF CHECK Self-diagnostic
messages
F P L
HIGH
HIGH
—
Applicability
Menu name
HIGH/LOW, –5 to 110%*3
J10 ZERO ADJ
K
Default Value
As specified when ordered.
If not specified, MPa.
H10 AUTO LRV
J
Remarks
Selected from mmH2O, mmAq,
mmWG, mmHg, Torr, Pa, hPa, kPa,
MPa, mbar, bar, gf/cm2, kgf/cm2,
inH2O, inHg, ftH2O, psi, or atm
NORMAL/REVERSE
NORMAL/REVERSE*4
Static pressure setting
units
D40 REV OUTPUT Output reversal
D45 H/L SWAP
Impulse piping
accessing direction
D52 BURN OUT
CPU error
D53 ERROR OUT Hardware error
D60 SELF CHECK Self-diagnostic
messages
E AUX SET 2
E10 DFS MODE
E14 TEMP
SELECT
E15 TEMP ZERO
Rewritability
History of the errors
—
Last error
Display the error
One time before
Display the error
Two time before
Display the error
Three time before
Display the error
Self-diagnostic
Same as A60
—
messages
*1: In case of Model EJA120A, static pressure cannot be measured. The display is always 0 MPa, but this is not a measured value.
*2: When Optional code /F1 is specified, substitute the value with 0.1.
*3: When Optional code /F1 is specified, substitute the value –5 with –2.5.
*4: Not applicable for Model EJA115.
*5: Applicable only for Model EJA118W, EJA118N, EJA118Y, EJA438W, and EJA438N.
*6: See MWP(max. working pressure) on the nameplate. B40 shows an approximate value of maximum pressure for the capsule.
T0806.EPS
8-5
IM 01C21C01-01E
8. BRAIN TERMINAL BT200 OPERATION
8.3.2
Parameter Usage and Selection
IMPORTANT
Before describing the procedure for setting parameters,
we present the following table showing how the
parameters are used and in what case.
If the transmitter is turned off within 30 seconds
after parameters have been set, the set data will
not be stored and the terminal returns to previous settings.
Table 8.3.1 Parameter Usage and Selection
Setup Item
Tag No. setup
P.8-7
Calibration range setup
P.8-7
Description
Sets the Tag No. (using 16 alphanumeric characters).
Note: Up to 8 alphanumerics (upper case letters) can be used in the BT100.
Sets the calibration range for 4 to 20 mA DC. Sets three data items: range unit, input value
at 4 mA DC (LRV), and input value at 20 mA DC (HRV).
Note: LRV and HRV can be specified with range value specifications up to 5 digits
(excluding any decimal point) within the range of –32000 to 32000.
Damping time constant setup
P.8-8
Adjusts the output response speed for 4 to 20 mA DC.
Can be set in 9 increments from 0.2 to 64 s.
Output signal low cut mode setup
P.8-9
Used mainly to stabilize output near 0% if output signal is the square root mode.
Two modes are available: forcing output to 0% for input below a specific value, or changing
to proportional output for input below a specific value.
Change the output limits
P.8-9
Integral indicator scale range and
unit setup
P.8-9
Change the range of normal output.
Sets the following 5 types of integral indicator scale ranges and units:
% scale indicator, user set scale indicator, alternate indication of user set scale
and % scale, input pressure display, alternate indication of input pressure and % scale
When using the user set scale, 4 types of data can be set:
user set scale setting, unit (BT200 only), display value at 4 mA DC (LRV), and display
value at 20 mA DC (HRV).
Note: LRV and HRV can be specified with range value specifications up to 5
digits (excluding any decimal point) within the range of –19999 to 19999.
Unit setup for displayed temperature
P.8-11
Sets a unit for temperatures displayed on the BT200.
Unit setup for displayed static
pressure P.8-11
Sets a unit for static pressure displayed on the BT200.
Operation mode (normal/reverse
signal) setup
P.8-11
Reverses the direction for 4 to 20 mA DC output relative to input.
Reverse mode is used for applications in which safety requires that output be
driven toward 20 mA if input is lost.
Output status display/setup when
a CPU failure P.8-12
Displays the status of 4 to 20 mA DC output when a CPU failure. The parameter
of the standard unit is fixed to the high limit value.
Output status setup when a hardware Sets the status of the 4 to 20 mA DC output when an abnormal status is detected
error occurs
with the capsule or the amplifier as the result of self-diagnosis. One of the
P.8-12
following statuses; last held, high limit, and low limit values, can be selected.
Range change (while applying
actual inputs)
P.8-12
Range for 4 to 20 mA DC signal is set with actual input applied. Sets 20 mA DC output
precisely with respect to user’s reference instrument output. Note that DPharp is calibrated
with high accuracy before shipment, so span should be set using the normal range setup.
Zero point adjustment
P.8-13
Adjusts zero point. This can be done either using the external zero-adjustment screw on
the transmitteror using the BT200.
Span adjustment
P.8-14
Adjust the characterization curve. All the transmitters are calibrated at factory and this
adjustment is normally not necessary for most cases. Use for specific purposes.
Test output (fixed current output)
setup P.8-15
Used for loop checks.
Output can be set freely from –5% to 110% in 1% steps.
User memo fields
P.8-15
Allows user to enter up to 5 items of any desired text in up to 8 uppercase
alphanumeric characters per item.
T0807.EPS
8-6
IM 01C21C01-01E
8. BRAIN TERMINAL BT200 OPERATION
8.3.3
Setting Parameters
Set or change the parameters as necessary. After
completing these, do not fail to use the “DIAG” key to
confirm that “GOOD” is displayed for the selfdiagnostic result at _60: SELF CHECK.
set data. The set data items flash.
When all items have been confir-
PRINTER OFF
F2:PRINTER ON
FEED POFF
NO
med, press the
again. (To go back to the setting
panel, press the
(NO) key.
(1) Tag No. Setup (C10: TAG NO)
Use the procedure below to change the Tag No. Up to
16 alphanumeric characters can be entered.
The DPharp TAG NO. was
SET
C10:TAG NO.
FIC-1a
FEED
overwritten.
Press the
NO
PARAM
C10:TAG NO.
FIC-1a
C20:PRESS UNIT
kPa
C21:LOW RANGE
0 kPa
DATA DIAG PRNT
• Example: Set a Tag No. to FIC-1a
Press the
the BT200.
This is the panel for confirming
SET
C10:TAG NO.
YOKOGAWA
FIC-1a
key to turn on
<When power is off>
OK
(OK) key to
return to the parameter panel.
Press the
(NO) key to
return to the setting panel.
ESC
F0811.EPS
––WELCOME––
BRAIN TERMINAL
ID: BT200
check connection
push ENTER key
UTIL
(2) Calibration Range Setup
Connect DPharp and BT200 using
a communication cable and press
the
key.
a. Setting Calibration Range Unit
(C20: PRESS UNIT)
The unit is set at the factory before shipment if
specified at the time of order. Follow the procedure
below to change the unit.
FEED
Displays the name of connected
DPharp model, TAG NO. and
diagnostics information. Press the
(OK) key after confirmation.
PARAM
01:MODEL
EJA110A-DM
02:TAG NO.
YOKOGAWA
03:SELF CHECK
GOOD
OK
MENU
A:DISPLAY
B:SENSOR TYPE
HOME
SET
ADJ
SET
SET
C20:PRESS UNIT
mmH20
< mmWG >
< mmHG >
< Torr >
< kPa >
ESC
MENU
C:SETTING
D:AUX SET 1
E:AUX SET 2
H:AUTO SET
HOME
• Example: Change the unit from mmH2O to kPa.
Press the
(SET) key to
display the SET menu panel.
Select C: SETTING and press the
key.
ADJ
Select C10: TAG NO. and press
the
key.
FEED
ESC
(OK) key.
NO
OK
MPa
mbar
bar
gf/cm2
kgf/cm2
inH2O
inHg
ftH2O
psi
atm
FICOGAWA
FIC-GAWA
FIC-1aWA
FIC-1a
SET
C10:TAG NO.
YOKOGAWA
FIC-1a _
Set TAG NO. and press the
key.
CLE
Press the
kPa
FIC-1AWA
caps
to enter the setting.
mmAq
mmWG
mmHg
Torr
Set the new TAG NO. (FIC-1a).
FOKOGAWA
CLR
key twice
mmH2O
ESC
FIKOGAWA
CODE
Press the
ESC
ESC
SET
C10:TAG NO.
YOKOGAWA
YOKOGAWA
CAPS
or
key to select “kPa.”
SET
C20:PRESS UNIT
kPa
MENU
C10:TAG NO.
YOKOGAWA
C20:PRESS UNIT
kPa
C21:LOW RANGE
0 kPa
DATA DIAG PRNT
CODE
Use the
F0812.EPS
ESC
When you have made an entry mistake, return
the cursor
using the key, then reenter.
F0810.EPS
8-7
IM 01C21C01-01E
8. BRAIN TERMINAL BT200 OPERATION
b. Setting Calibration Range Lower
Range Value and Higher Range Value
(C21: LOW RANGE, C22: HIGH
RANGE)
These range values are set as specified in the order
before the instrument is shipped. Follow the procedure
below to change the range.
• Example 2: With present settings of 0 to 30 kPa,
set the Higher range value to10 kPa.
SET
C22:HIGH RANGE
30 kPa
+
10
DEL
FEED
PARAM
C20:PRESS UNIT
kPa
C21:LOW RANGE
0 kPa
C22:HIGH RANGE
10 kPa
DATA DIAG PRNT
• Example 1: With present settings of 0 to 30 kPa,
set the lower range value to 0.5 kPa.
DEL
CLR
Set 0.5.
Press the
enter the setting.
FEED
NO
SET
C20:PRESS UNIT
kPa
C21:LOW RANGE
0.5 kPa
C22:HIGH RANGE
30.5 kPa
DATA DIAG PRNT
Press the
Press the
(OK) key.
OK
The low range value is not
changed, so the span changes.
ESC
key twice to
F0814.EPS
ESC
SET
C21:LOW RANGE
0.5 kPa
NO
key twice
ESC
SET
C22:HIGH RANGE
10 kPa
• The measurement span is determined by the high and
low range limit values. In this instrument, changing
the low range value also automatically changes the
high range value, keeping the span constant.
SET
C21:LOW RANGE
0 kPa
+
0.5
CLR
Set 10.
Press the
to enter the setting.
(3) Damping Time Constant Setup
(C30: AMP DAMPING)
When the instrument is shipped, the damping time
constant is set at 2.0 seconds. Follow the procedure
below to change the time constant.
(OK) key.
OK
The higher range value is changed
while the span remains constant.
• Example: Change from 2.0 sec to 4.0 sec.
SET
C30:AMP DAMPING
2.0 sec
<
2.0 sec
<
4.0 sec
<
8.0 sec
<
16.0 sec
ESC
Span = Higher range value – Lower range value
>
>
>
>
ESC
SET
C30:AMP DAMPING
4.0 sec
F0813.EPS
• Note, however, that changing the higher range value
does not cause the lower range value to change.
Thus, changing the higher range value also changes
the span.
• Calibration range can be specified with range value
specifications up to 5 digits (excluding any decimal
point) for low or high range limits within the range
of –32000 to 32000.
FEED
NO
Use the
or
select 4.0 sec.
Press the
enter the setting.
Press the
key to
key twice to
(OK) key.
OK
0.2sec
0.5sec
1.0sec
2.0sec
4.0sec
8.0sec
16.0sec
32.0sec
64.0sec
F0815.EPS
Note: The damping time constant set here is the damping time
constant for the amplifier assembly. The damping time
constant for the entire transmitter is the sum of the values for
the amplifier assembly and for the capsule assembly. For the
capsule assembly damping time constant (fixed), see the
“General Specifications” found at the end of this manual.
(See Chapter 10.)
8-8
IM 01C21C01-01E
8. BRAIN TERMINAL BT200 OPERATION
(4) Output Signal Low Cut Mode Setup
(D10: LOW CUT, D11: LOW CUT MODE)
Low cut mode can be used to stabilize the output
signal near the zero point. The low cut point can be set
in a range from 0 to 20% of output. (Hysteresis: ±1%)
(5) Change Output Limits
(D15:OUT LIMIT(L), D16:OUT LIMIT(H))
The range of normal output is preset at factory from
-5.0 to 110.0% unless otherwise specified, and the
output is limited with these upper and lower values.
This output range can be changed, for example, to
meet the requirements of NAMUR, etc. within the
settable range. Set the lower limit with D15:OUT
LIMIT(L) and upper limit with D16:OUT LIMIT(H).
Select “ZERO” as the low cut mode.
Low cut mode “ZERO”
(%)
50
Settable range : -5.0 to 110.0 (%)
Lower limit < Upper limit
Output
(6) Integral Indicator Scale Setup
The following 5 displays are available for integral
indicators.
20
0
Input
50 (%)
F0816.EPS
D20: DISP SELECT
and Display
• Example: Change the low cut setting range
from 10% to 20%, and the low
cut mode from LINEAR to ZERO.
NORMAL %
Press the
key twice to
USER SET
enter the setting.
CLR
ESC
SET
D10:LOW CUT
20.0 %
Press the
NO
A11:ENGR.OUTPUT
20.0 M
USER & %
OK
Use the
SET
D11:LOW CUT MODE
LINEAR
< LINEAR >
< ZERO
>
or
key
Press the
SET
D11:LOW CUT MODE
ZERO
key twice to
enter the setting.
Press the
Indicates user set and % alternately
in 3 second intervals.
A10:OUTPUT (%)
45.6 %
A11:ENGR. OUTPUT
20.0 M
to select “ZERO.”
ESC
Indicates values depending on the
Engineering range (D22, D23).(Note 1)
Units set using Engineering unit
(D21) are not indicated.
(OK) key.
Next, the [D11: LOW CUT MODE]
setting panel is displayed.
FEED
Indicates –5 to 110% range
depending on the Measurement
range (C21, C22).
A10:OUTPUT (%)
45.6 %
Set 20.
SET
D10:LOW CUT
10.0 %
+
20.0
Description
and Related parameters
INP PRES
(OK) key.
Indicates input pressure.(Note 2)
Indication limits –19999 to 19999.
A40:INPUT
456 kPa
FEED
NO
OK
PRES & %
PARAM
D10:LOW CUT
20.0 %
D11:LOW CUT MODE
ZERO
D20:DISP SELECT
NORMAL %
DATA DIAG PRNT
Indicates input pressure and %
alternately in 3 second intervals.
A10:OUTPUT (%)
45.6 %
A40:INPUT
456 kPa
ESC
F0817.EPS
(Note 1) Scale range can be specified with range limit specifications up
to 5 digits (excluding any decimal point) for low or high range
limits within the range of –19999 to 19999.
The range with decimals is available to the third decimal place.
(Note 2) It indicates the value after zeroing.
T0808.EPS
See (a.) through (c.) for each setting procedure.
8-9
IM 01C21C01-01E
8. BRAIN TERMINAL BT200 OPERATION
% indication and
input pressure
indication
User-set engineering
unit display
D20: DISP SELECT
NORMAL %
INP PRES
PRES & %
D20: DISP SELECT
USER SET
USER & %
b. Setting User-set Engineering Unit
(D21: DISP UNIT)
This parameter allows entry of the engineering units to
be displayed on the BT200. When the instrument is
shipped, this is set as specified in the order.
Follow the procedure below to change this setting.
This parameter need not be set for % display.
Set for user-set
engineering unit display.
Transmitter is set
• Example: Set an engineering unit M.
for “% display” when
shipped.
Set “M.”
SET
D21:DISP UNIT
D21: DISP UNIT
Press the
M_
Set a unit to be
displayed on the BT200.
key twice to
enter the setting.
CODE
CAPS
CLR
ESC
Press the
SET
D21:DISP UNIT
M
D22: DISP LRV
Set a numeric value for
engineering unit for 4 mA
output (LRV).
FEED
NO
(OK) key.
OK
F0820.EPS
D23: DISP HRV
Set a numeric value for
engineering unit for 20 mA
output (HRV).
F0818.EPS
a. Display Selection (D20: DISP SELECT)
Follow the instructions given to the below to change
the range of integral indication scales.
When USER SET is selected, the user set values of
integral indication and A11: ENGR. OUTPUT
parameter are indicated.
• Example: Set the integral indicator scale to
engineering units display.
Use the
SET
D20:DISP SELECT
NORMAL %
<NORMAL %>
<USER SET>
<USER & %>
<INP PRES>
Press the
ESC
SET
D20:DISP SELECT
USER SET
FEED
NO
or
key
to select “USER SET.”
key twice to
enter the setting.
Press the
(OK) key.
OK
The “%” disappears from the
integral indicator display.
F0819.EPS
8-10
IM 01C21C01-01E
8. BRAIN TERMINAL BT200 OPERATION
c. Lower and Higher Range Value Setup
in Engineering Unit (D22: DISP LRV,
D23: DISP HRV)
These parameter items are used to set the lower and
higher range values for the engineering unit display.
(8) Unit Setup for Displayed Static Pressure
(D31: STAT.P.UNIT)
Follow the procedure below to change the static
pressure units.
Changing this parameter changes the unit for the A30:
STATIC PRESS (static pressure) display.
When the instrument is shipped, these are set as
specified in the order. Follow the procedure below to
change these settings. Note that these parameters need
not be set for % display.
• Example: Change the static pressure unit from
kgf/cm2 to MPa.
SET
D31:STAT.P.UNIT
kgf/cm^2
< MPa
>
< mbar
>
< bar
>
< gf/cm^2 >
• Example: Set lower range value (LRV) to –50
and higher range value (HRV) to 50.
Set –50.
SET
D22:DISP LRV
0M
50
Press the
key twice to
ESC
Set 50.
CLR
key twice to
enter the setting.
kgf/cm2
Press the
inH2O
inHg
ftH2O
psi
atm
key twice to
enter the setting.
DEL
Press the
MPa
mbar
bar
gf/cm2
Setting HRV
SET
D23:DISP HRV
100M
+
50
key
mmH2O
mmAq
mmWG
mmHg
Torr
kPa
enter the setting.
CLR
or
to select MPa.
ESC
Setting LRV
DEL
Use the
ESC
F0823.EPS
Press the
SET
D23:DISP HRV
50M
FEED
NO
PARAM
D21:DISP
M
D22:DISP
–
D23:DISP
DATA
(OK) key.
(9) Operation Mode Setup
(D40: REV OUTPUT)
This parameter allows the direction of the 4 to 20 mA
output to be reversed with respect to input. Follow the
procedure below to make this change.
OK
UNT
LRV
50M
HRV
50M
DIAG PRNT
• Example: Change 4 to 20 mA output to 20 to
4 mA output.
ESC
F0821.EPS
Use the
SET
D40:REV OUTPUT
NORMAL
< NORMAL >
< REVERSE>
(7) Unit Setup for Displayed Temperature
(D30: TEMP UNIT)
When the instrument is shipped, the temperature units
are set to degC. Follow the procedure below to
change this setting. Note that changing the unit here
changes the unit for A20: AMP TEMP (amplifier
temperature) and A21: CAPSULE TEMP (capsule
temperature).
or
key
to select REVERSE.
Press the
ESC
key twice to
enter the setting.
F0824.EPS
• Example: Change the unit for the temperature
display.
SET
D30:TEMP UNIT
deg C
< deg C >
< deg F >
Use the
or
key to
select “deg F.”
Press the
ESC
key twice to
enter the setting.
F0822.EPS
8-11
IM 01C21C01-01E
8. BRAIN TERMINAL BT200 OPERATION
(10) Output Status Display/Setup when a CPU
Failure (D52: BURN OUT)
This parameter displays the status of 4 to 20 mA DC
output if a CPU failure occurs. In case of a failure,
communication is disabled.
(12) Range Change while Applying Actual
Inputs (H10: AUTO LRV, H11: AUTO
HRV)
This feature allows the lower and higher range values
to be set up automatically with the actual input applied.
If the lower and higher range values are set, C21:
LOW RANGE and C22: HIGH RANGE are changed
at this same time.
Setting of HIGH or LOW is enabled. This is done with
the pin (CN4) on the CPU assembly. See Chapter 3 for
details.
Follow the procedure in the figure below.
The measurement span is determined by the higher and
lower range values. Changing the lower range value
results in the higher range value changing automatically, keeping the span constant.
Standard specifications
The parameter is set to HIGH. If a failure, the transmitter outputs the signal of 110% or higher. The parameter
D53: ERROR OUT is set to HIGH from the factory.
Optional code/C1
The parameter is set to LOW. If a failure, output which
is –5% or lower is generated. The parameter D53:
ERROR OUT is set to LOW from the factory.
• Example 1: When changing the lower range
value to 0.5 kPa for the present
setting of 0 to 30 kPa, take the
following action with input pressure
of 0.5 kPa applied.
• Example: Standard specifications
D52: BURN
HIGH
pin (CN4) position: H
OUT
SET
H10:AUTO LRV
0 kPa
+
0
Press the
• Example: Optional code/C1
D52: BURN
LOW
to 0.5 kPa.
ESC
pin (CN4) position: L
OUT
key twice.
The lower range value is changed
SET
H10:AUTO LRV
0.5000 kPa
Press the
(OK) key.
F0825.EPS
FEED
(11)
Output Status Setup when a Hardware
Error Occurs (D53: ERROR OUT)
This parameter allows the setting of the output status
when a hardware error occurs. The following three
selections are available.
NO
PARAM
H10:AUTO LRV
0.5000 kPa
H11:AUTO HRV
30.500 kPa
H60:SELF CHEC
GOOD
DATA DIAG PRNT
(a) HOLD; Outputs the last value held before the error
occurred.
(b) HIGH; Outputs an output of 110% when an error
has occurred.
(c) LOW; Outputs an output of –5% when an error has
occurred.
OK
The higher range value is changed
keeping the span constant.
Parameters C21 and C22 are
ESC
changed at the same time.
F0827.EPS
Note that changing the higher range value does not
cause the lower range value to change but does change
the span.
Note: A hardware error means CAP MODULE FAULT of Er.01 or
AMP MODULE FAULT of Er. 02 which are shown in 8.5.2
“Errors and Countermeasures.”)
• Example: Set the output status to LOW when
a hardware error occurs.
SET
D53:ERROR OUT
HIGH
<
HIGH>
<
LOW>
<
HOLD>
Use the
or
key
to select LOW.
Press the
ESC
key twice to
enter the setting.
F0826.EPS
8-12
IM 01C21C01-01E
8. BRAIN TERMINAL BT200 OPERATION
• Example 2: When the higher range value is to
be changed to 10 kPa with the
present setting of 0 to 30 kPa, take
the following action with an input
pressure of 10 kPa applied.
SET
H11:AUTO HRV
30 kPa
+
30
Press the
(a) Follow the procedure below when setting the
present output to 0% (4 mA).
Output is 0.5%.
A10:OUTPUT (%)
0.5 %
key twice.
SET
J10:ZERO ADJ
0.0 %
+ 000.0
The higher range value is changed
to 10 kPa.
Press the
key twice.
ESC
CLR
SET
H11:AUTO HRV
10.000 kPa
FEED
NO
PARAM
H10:AUTO LRV
0 kPa
H11:AUTO HRV
10.000 kPa
H60:SELF CHECK
GOOD
DATA DIAG PRNT
Press the
ESC
(OK) key.
SET
J10:ZERO ADJ
0.0 %
Zero adjustment is completed.
Press the
(OK) key.
OK
FEED
The lower range value is not
changed, so the span changes.
OK
Output is 0%.
A10:OUTPUT (%)
0.0 %
Parameter C22 is changed at the
ESC
NO
same time.
F0829.EPS
F0828.EPS
(b) In tank level measurement, if the actual level
cannot be brought to zero for zero adjustment, then
the output can be adjusted to correspond to the
actual level obtained using another measuring
instrument such as a glass gauge.
(13)
Zero Point Adjustment
(J10: ZERO ADJ, J11: ZERO DEV,
J20: EXT ZERO ADJ)
The DPharp supports several adjustment methods.
Select the method best suited for the conditions of your
application.
Note that output signal can be checked by displaying
parameter A10:OUTPUT (%) on the BT200.
Adjustment Method
Using the BT200
Present level: 45%
Present output: 41%
100%
Present level
45%
Description
Set the present input to 0%.
Adjust for 0% output at input level of
0%.
0%
Adjust output to the reference value
obtained using other means.
If the input level cannot easily be
made 0% (because of tank level,
etc.), adjust output to the reference
value obtained using other means,
such as a sight glass.
Using the external
zero-adjustment
screw
F0830.EPS
(b)-1 Follow the procedure below to use J10: ZERO
ADJ.
Present output is 41.0%.
A10:OUTPUT (%)
41.0 %
Adjust zero point using the zeroadjustment screw on the transmitter.
This permits zero adjustment without
using the BT200. Accurately adjust
the output current to 4 mA DC or
other target output value using an
ammeter that accuratly reads output
currents.
SET
J10:ZERO ADJ
0.0 %
+ 045.0
CLR
T0809.EPS
A10:OUTPUT (%)
45.0 %
Enter the present actual level, 45%.
Press the
key twice.
ESC
The output is changed to 45%.
F0831.EPS
8-13
IM 01C21C01-01E
8. BRAIN TERMINAL BT200 OPERATION
(b)-2 Follow the procedure below to use J11: ZERO
DEV.
• Example: Inhibiting zero adjustment by the
external zero-adjustment screw
SET
J20:EXIT ZERO ADJ
ENABLE
< ENABLE >
< INHIBIT>
Present output is 41.0%.
A10:OUTPUT (%)
41.0 %
Output error = 45.0 – 41.0 = 4.0%.
Use the
Press the
SET
J11:ZERO DEV.
2.50 %
0
Since “J11: ZERO DEV.” contains
or
key to
select INHIBIT.
ESC
key twice to
enter the setting.
the previous correction, obtain the
F0833.EPS
correction value by adding 4.0% to
ESC
SET
J11:ZERO DEV.
2.50 %
6.50
• Zero point adjustment using external zero-adjustment
screw on the transmitter
it. (2.50% + 4.0% = 6.50%)
Set the correction value, 6.50.
Press the
Turn the zero-adjustment screw on the outside of the
transmitter case using a slotted screwdriver. Turn the
screw to the right to increase the zero point or to the
left to decrease the zero output; the zero adjusts in
increments of 0.01% of the range setting.
Note that the amount of adjustment to the zero point
changes according to the speed at which the screw is
turned. To make fine adjustments, turn the screw
slowly; to make coarse adjustments, turn the screw
quickly.
key twice.
ECS
The output is changed to 45%.
A10:OUTPUT (%)
45.0 %
F0832.EPS
When the zero point is adjusted, the displayed value of
A40 is as follows.
[Example]
When the zero point is shifted by 20 kPa for the actual
pressure, the parameter of A40 indicates 50 kPa.
Note: When a zero point adjustment has been made, do not turn off
the transmitter less than 30 seconds after adjustment.
(14) Span Adjustment
Each DPharp EJA series transmitter is factory characterized according to the specification. Mounting
position effects or zero shifts caused by static pressure
are typically compensated by a zero adjustment.
70 kPa
50 kPa
20 kPa
0 kPa
Zero adjustment
volume(J11)
Zero
adjustment
Actual differential
pressure/pressure
A span adjustment is a function to correct the slope
error from a zero point in characterizing 100% point
(HRV). This function can be used when span drifts
may be caused or characterization to the specific
pressure standard is required.
0 kPa
Input value
of A40
F0841.EPS
(c) Zero Point Adjustment Using the External Zero
Adjustment Screw
Therefore, the zero point adjustment should always be
performed before the upper point adjustment in order
to maintain the pitch between zero and 100% points
within the calibration range.
• Enabling/inhibiting of zero point adjustment using the
external zero-adjustment screw on the transmitter
(J20: EXT ZERO ADJ)
You can manually perform the trimming procedure by
using J15: SPAN ADJ.
Follow the procedure below to enable or inhibit zero
point adjustment from the zero-adjustment screw on
the transmitter.
This is set to “ENABLE” when the instrument is
shipped.
• Span adjustment value
The span adjustment value is calculated as follows.
8-14
IM 01C21C01-01E
8. BRAIN TERMINAL BT200 OPERATION
Span adjustment value (%) = P1 A40 100
P1
P1: Actual differential pressure/pressure value
A40: Input (indicated as the value after zeroing)
(15) Test Output Setup (K10: OUTPUT X%)
This feature can be used to output a fixed current from
3.2 mA (–5%) to 21.6 mA (110%) for loop checks.
• Example: Output 12 mA (50%) fixed current.
Measurement pressure
SET
K10:OUTPUT X %
0.0 %
+
050.0
A40
Set 50.0%.
Press the
key twice to
output a fixed current at 50%.
ESC
Applied pressure
P1
0
SET
K10:OUTPUT X %
50.0 % ACTIVE
F0846.EPS
“Active” is displayed while this is
being executed.
Press the
FEED
(OK) key to cancel
the fixed current output.
IMPORTANT
Suppose that a standard pressure of 30 kPa is applied and
the value of the parameter of A40: INPUT is 30.15 kPa.
Firstly, obtain the slope error for the span as follows;
OK
F0834.EPS
• Example: For the range of 0 to 30 kPa.
A40: INPUT = 30.15 kPa
J15: SPAN ADJ = 0.15 %
Span adjustment value (%) =
NO
1. Test output is held for approximately 10
minutes, and then released automatically after
the time has elapsed. Even if the BT200 power
supply is turned off or the communication cable
is disconnected during test output, it is held for
approximately 10 minutes.
2. Press the
(OK) key to release test output
immediately.
P1 A40
100
P1
30.0030.15
100 = 0.5 (%)
30.00
Add 0.5% to 0.15% of the current value to calculate the
accumulated span adjustment value.
0.15 (0.50) = 0.35
DEL
Press
CLR
Press the
NO
key twice.
ESC
SET
J15:SPAN ADJ
-0.35 %
FEED
(16) User Memo Fields (M: MEMO)
This feature provides 5 user memo fields, each holding
up to 8 alphanumeric characters. Up to 5 items such as
inspection date, inspector, and other information can be
saved in these fields.
Set 0.35.
SET
J15:SPAN ADJ
0.15 %
0.35
(OK) key.
• Example: Save an inspection date of January
30, 1995.
OK
PARAM
M10:MEMO 1
Note: Enter 0.00 to J15: SPAN ADJ to reset the
span adjustment to the initial value at the
shipment.
Set 95.1.30 in the order of year,
month, and day.
M20:MEMO 2
M30:MEMO 3
DATA
DIAG
Press the
PRNT
ESC
F0847.EPS
key twice to
enter the setting.
SET
M10:MEMO 1
95.1.30_
ESC
F0835.EPS
8-15
IM 01C21C01-01E
8. BRAIN TERMINAL BT200 OPERATION
8.4 Displaying Data Using the
BT200
8.4.1
8.5 Self-Diagnostics
8.5.1
Displaying Measured Data
Checking for Problems
(1) Identifying Problems with BT200
The following four areas can be checked.
(a) Whether connections are good.
(b) Whether BT200 was properly operated.
(c) Whether settings were properly entered.
(d) History of the errors.
See examples below.
The BT200 can be used to display measured data.
The measured data is updated automatically every 7
seconds. In addition, the display can be updated to the
present data value at any time by pressing the
(DATA) key. For parameters associated with the
display of measured data, see Subsection 8.3.1,
“Parameter Summary.”
• Example 1: Connection errors
––WELCOME––
BRAIN TERMINAL
ID: BT200
• Example: Display output.
Press the
check connection
push ENTER key
MENU
A:DISPLAY
B:SENSOR TYPE
UTIL
key.
When the panel shown on the left
appears, press the
key.
FEED
Since communications will be
HOME
SET
ADJ
ESC
communication error
PARAM
A10:OUTPUT (%)
XX.X %
A11:ENGR.OUTPUT
YY.Y %
A20:AMP TEMP
ZZ deg C
DATA DIAG PRNT
PARAM
A10:OUTPUT (%)
Display “A10: OUTPUT (%).”
unsuccessful if there is a problem
in the connection to the BT200, the
ESC
display at the left will appear.
Recheck the connection.
ESC
communi
Data is updated automatically
at 7-second intervals.
Press the
(OK) key.
A11:ENGR.OUTPUT
• Example 2: Setting entry errors
A20:AMP TEMP
F0836.EPS
8.4.2 Display Transmitter Model and
Specifications
PARAM
C20:PRESS UNIT
kPa
C21:LOW RANGE
600 kPa
C22:HIGH RANGE
600 kPa
DATA DIAG PRNT
diagnostics.
Press the
.
FEED
PRNT
(DIAG) key in the
parameter panel to go to the
diagnostics panel
ESC
(C60: SELF CHECK).
An error message is displayed
DIAG
C60:SELF CHECK
ERROR
<
ERROR
>
<
ILLEGAL LRV >
• Example: View transmitter model name.
Press
result of current transmitter
OK
The BT200 can be used to display the model and
specifications of the transmitter.
MENU
A:DISPLAY
B:SENSOR TYPE
The initial data panel shows the
PARAM
01:MODEL
EJA210A-DM
02:TAG NO.
YOKOGAWA
03:SELF CHECK
ERROR
when an error occurs in the
diagnostics panel.
ESC
F0838.EPS
HOME
SET
ADJ
PARAM
B10:MODEL
EJA210A-DM
B11:STYLE NO.
S1.01
B20:LRL
– 98.07 kPa
DATA DIAG PRNT
ESC
For the associated
parameters, see Subsection
8.3.1, Parameter Summary.
ESC
F0837.EPS
8-16
IM 01C21C01-01E
8. BRAIN TERMINAL BT200 OPERATION
(2) Checking with Integral Indicator
• Example 3: Checking the history of the errors
Connect the BT200 to the
transmitter, and call item P.
MENU
J:ADJUST
K:TEST
M:MEMO
P:RECORD
HOME
SET
ADJ
ESC
PARAM
P10:ERROR REC 1
ERROR
P11:ERROR REC 2
ERROR
P12:ERROR REC 3
GOOD
DATA DIAG PRNT
ESC
NOTE
If an error is detected in the self-diagnostic, an
error number is displayed on the integral indicator. If there is more than one error, the error
number changes at two-second intervals. See
Table 8.5.1 regarding the error numbers.
P10: “ERROR REC 1” displays the last error.
P11: “ERROR REC 2” displays the error one time before
the last error occurred.
P12: “ERROR REC 3” displays the error two times before
the last error occurred.
P13: “ERROR REC 4” displays the error three times before
the last error occurred.
The history of up to four errors can be stored. When the 5th
error has occurred, it is stored in “P10”. The error stored in
“P13” will be deleted, and then, the error in “P12” will be
copied to “P13”. In this sequence, the history of the most
previously occurred error will be removed from memory.
“GOOD” will be displayed if there was no previous error.
F0840.EPS
Figure 8.5.1 Identifying Problems Using the Integral
Indicator
Select P10: ERROR REC1 and
press the
key to display
the error message.
SET
P10:ERROR REC 1
ERROR
<
ERROR
>
<
ILLEGAL LRV >
<
ILLEGAL HRV >
ESC
<(a) SETUP PANEL>
For the details of the messages listed below, see Table
8.5.1 Error Message Summary.
OVER TEMP (CAP)
ILLEGAL LRV
AMP MODULE FAULT OVER TEMP (AMP)
ILLEGAL HRV
CAP MODULE FAULT
OUT OF RANGE
OVER OUTPUT
ILLEGAL SPAN
OUT OF SP RANGE
OVER DISPLAY
ZERO ADJ OVER
Note 1: Press the
key twice in the setting panel
(panel 1) to clear all error message (P10 to P13)
information.
Note 2: After two hours from when an error occurs, the error
message of that error will be recorded. Therefore,
if you switch off the transmitter within two hours from
when the error occurs, there is no history of that
error stored in the transmitter, and this function is
meaningless.
F0839.EPS
8-17
IM 01C21C01-01E
8. BRAIN TERMINAL BT200 OPERATION
8.5.2
Errors and Countermeasures
The table below shows a summary of error messages.
Table 8.5.1 Error Message Summary
Integral
Indicator
Display
BT200 Display
Cause
Output Operation
during Error
Countermeasure
None
GOOD
----
ERROR
Er. 01
CAP MODULE
FAULT
Capsule problem.*1
Outputs the signal
(Hold, High, or Low)
set with parameter
D53.
Replace the capsule
when error keeps
appearing even after
restart.*2
Er. 02
AMP MODULE
FAULT
Amplifier problem.
Outputs the signal
(Hold, High, or Low)
set with parameter
D53.
Replace amplifier.
Er. 03
OUT OF RANGE
Input is outside
measurement range
limit of capsule.
Outputs high range
limit value or low
range limit value.
Check input.
Er. 04
OUT OF SP
RANGE
Static pressure
exceeds specified
range.*3
Displays present
output.
Check line pressure
(static pressure).
Er. 05
OVER TEMP
(CAP)
Capsule temperature
is outside range
(–50 to 130°C).
Displays present
output.
Use heat insulation or
make lagging to keep
temperature within
range.
Er. 06
OVER TEMP
(AMP)
Amplifier temperature
is outside range
(–50 to 95°C).
Displays present
output.
Use heat insulation or
make lagging to keep
temperature within
range.
Er. 07
OVER OUTPUT
Output is outside high Outputs high or low
or low range limit
range limit value.
value.
Check input and range
setting, and change
them as needed.
Er. 08
OVER DISPLAY
Displayed value is
outside high or low
range limit value.
Check input and
display conditions and
modify them as
needed.
Er. 09
ILLEGAL LRV
LRV is outside setting Holds output
range.
immediately before
error occurrence.
Check LRV and
modify as needed.
Er. 10
ILLEGAL HRV
HRV is outside setting Holds output
range.
immediately before
error occurrence.
Check HRV and
modify as needed.
Er. 11
ILLEGAL SPAN
SPAN is outside
setting range.
Check SPAN and
change as needed.
Er. 12
ZERO ADJ OVER Zero adjustment is too Displays present
large.
output.
Displays high or low
range limit value.
Holds output
immediately before
error occurrence.
Readjust zero point.
*1: This error code appears at a capsule problem or when an illegal overpressure is applied to the
pressure sensor.
*2: If the normal pressure is regained, the Er.01 will disappear according to the setting of the parameter
of E50: AUTO RECOVER. When the E50: AUTO RECOVER is set to ON(defalut setting), the Er.01
will disappear automatically. When the E50: AUTO RECOVER is set to OFF, restart the transmitter
to cancel Er.01. If no error code appears then, perform necessary adjustment such as zero-adjustment to continue the operation. If the error code still exists, replace the capsule assembly.
*3: For Model EJA120A, static pressure cannot be measured. The display is always 0 MPa, but this is
not a measured value.
T0811 .EPS
8-18
IM 01C21C01-01E
9. MAINTENANCE
9.
MAINTENANCE
9.1 Overview
WARNING
Since the accumulated process fluid may be
toxic or otherwise harmful, take appropriate care
to avoid contact with the body, or inhalation of
vapors during draining condensate or venting
gas in transmitter pressure-detector section and
even after dismounting the instrument from the
process line for maintenance.
Maintenance of the transmitter is easy due to its
modular construction. This chapter describes the
procedures for calibration, adjustment, and the disassembly and reassembly procedures required for
component replacement.
9.2 Calibration Instruments Selection
Table 9.2.1 shows the instruments required for calibration. Select instruments that will enable the transmitter
to be calibrated or adjusted to the required accuracy.
The calibration instruments should be handled carefully
so as to maintain the specified accuracy.
9.3 Calibration
Use the procedure below to check instrument operation
and accuracy during periodic maintenance or troubleshooting.
1) Connect the instruments as shown in Figure 9.3.1
and warm up the instruments for at least five
minutes.
Since the transmitters are precision instruments,
carefully and thoroughly read the following sections
for proper handling during maintenance.
IMPORTANT
• To adjust the transmitter for highest accuracy,
make adjustments with the power supply
voltage and load resistance including leadwire
resistances set close to the conditions under
which the transmitter is installed.
• If the measurement range 0% point is 0 kPa or
shifted in the positive direction (suppressed
zero), the reference pressure should be applied
as shown in the figure (low pressure side open
to atmosphere). If the measurement range 0%
point is shifted in the negative direction (elevated zero), the reference pressure should be
applied on the low pressure side (high pressure
side open to atmosphere).
• Do not perform the calibration procedure until
the transmitter is at room temperature.
IMPORTANT
• As a rule, maintenance of this transmitter
should be implemented in a maintenance
service shop where the necessary tools are
provided.
• The CPU assembly contains sensitive parts
that may be damaged by static electricity.
Exercise care so as not to directly touch the
electronic parts or circuit patterns on the board,
for example, by preventing static electrification
by using grounded wrist straps when handling
the assembly. Also take precautions such as
placing a removed CPU assembly into a bag
with an antistatic coating.
2) Apply reference pressures of 0%, 50%, and 100% of
the measurement range to the transmitter. Calculate
the errors (differences between digital voltmeter
readings and reference pressures) as the pressure is
increased from 0% to 100% and is decreased from
100% to 0%, and confirm that the errors are within
the required accuracy.
9-1
IM 01C21C01-01E
9. MAINTENANCE
Table 9.2.1 Instruments Required for Calibration
Name
Yokogawa-recommended Instrument
Power
supply
4 to 20 mA DC signal
Model SDBT or SDBS distributor
Model 2792 standard resistor [250 Ω ±0.005%, 3 W]
Load
resistor
Load adjustment resistor [100 Ω ±1%, 1 W]
Model 2501 A digital multimeter
Accuracy (10V DC range): ±(0.002% of rdg + 1 dgt)
Voltmeter
Digital
manometer
Pressure
generator
Pressure
source
Remarks
Model MT220 precision digital manometer
1) For 10 kPa class
Accuracy: ±(0.015% of rdg + 0.015% of F.S.) . . . . .
±(0.2% of rdg + 0.1% of F.S.) . . . . . . . . .
2) For 130 kPa class
Accuracy: ±0.02% of rdg . . . . . . . . . . . . . . . . . . . . . .
..........................
±5digits
±(0.2% of rdg + 0.1% of F.S.) . . . . . . . . .
3) For 700 kPa class
Accuracy: ±(0.02% of rdg + 3digits) . . . . . . . . . . . . .
.........................
±5 digits
±(0.2% of rdg + 0.1% of F.S.) . . . . . . . . .
4) For 3000 kPa class
Accuracy: ±(0.02% of rdg + 10 digits) . . . . . . . . . . .
±(0.2% of rdg + 0.1% of F.S.) . . . . . . . . .
5) For 130 kPa abs class
Accuracy: ±(0.03% of rdg + 6 digits) . . . . . . . . . . . .
for 0 to 10 kPa
for -10 to 0 kPa
for 25 to 130 kPa
for 0 to 25 kPa
for -80 to 0 kPa
for 100 to 700 kPa
for 0 to 100 kPa
for -80 to 0 kPa
Select a manometer having
a pressure range close to
that of the transmitter.
for 0 to 3000 kPa
for -80 to 0 kPa
for 0 to 130 kPa abs
Model 7674 pneumatic pressure standard for 200 kPa {2 kgf/cm2}, 25 kPa {2500 mmH2O} Requires air pressure
Accuracy: ±0.05% of F.S.
supply.
Dead weight gauge tester 25 kPa {2500mmH2O}
Accuracy: ±0.03% of setting
Select the one having a
pressure range close to
that of the transmitter.
Model 6919 pressure regulator (pressure pump)
Pressure range: 0 to 133 kPa {1000 mmHg}
Prepare the vacuum pump
for negative pressure
ranges.
T0901.EPS
Note: The above table contains the instruments capable of performing calibration to the 0.2% level. Since special maintenance and management
procedures involving traceability of each instrument to higher-level standards are required for calibration to the 0.1% level, there are
difficulties in calibration to this level in the field. For calibration to the 0.1% level, contact Yokogawa representatives from which the
instrument was purchased or the nearest Yokogawa office.
Terminal box
Load resistance, 250 Ω
Rc
Power
supply
E
(Note) For Model EJA220A transmitter
(diaphragm-extended type), prepare a
mating calibration flange to match
the diaphragm extension length and
outer diameter.
R
Load adjusting
resistance, 100 Ω
V
Digital voltmeter
Model 7674 pneumatic
pressure standards
Supply pressure
P
Model MT220
precision
digital manometer
Mating (Note)
calibration
flange
P
Pressure source
Reference pressure
F0901.EPS
Figure 9.3.1 Instrument Connections
9-2
IM 01C21C01-01E
9. MAINTENANCE
9.4 Disassembly and Reassembly
9.4.1 Replacing the Integral Indicator
CAUTION
This section describes procedures for disassembly and
reassembly for maintenance and component replacement.
Cautions for Flameproof Type Transmitters
Users are prohibited by law from modifying the
construction of a flameproof type transmitter.
This would invalidate the agency approval and
the transmitter’s use in such rated area.
Thus the user is prohibited from using a flameproof type transmitter with its integral indicator
removed, or from adding an integral indicator to
a transmitter. If such modification is absolutely
required, contact Yokogawa.
Always turn OFF power and shut off and release
pressures before disassembly. Use proper tools for all
operations. Table 9.4.1 shows the tools required.
Table 9.4.1 Tools for Disassembly and Reassembly
Tool
Quantity
Phillips screwdriver
1
Slotted screwdriver
1
Allen wrenches
2
Wrench
1
Remarks
JIS B4633, No. 2
JIS B4648
One each, nominal 3 and
5 mm Allen wrenches
Width across flats, 17 mm
Torque wrench
1
Adjustable wrench
1
Socket wrench
1
Width across flats, 16 mm
Socket driver
1
Width across flats, 5.5 mm
Tweezers
1
T0902.EPS
CAUTION
Precautions for CENELEC and IECEx Flameproof Type Transmitters
• Flameproof type transmitters must be, as a
rule, removed to a non-hazardous area for
maintenance and be disassembled and reassembled to the original state.
• On the flameproof type transmitters the two
covers are locked, each by an Allen head bolt
(shrouding bolt). When a shrouding bolt is
driven clockwise by an Allen wrench, it is going
in and cover lock is released, and then the
cover can be opened.
When a cover is closed it should be locked by a
shrouding bolt without fail. Tighten the shrouding bolt to a torque of 0.7 N·m.
This subsection describes the procedure for replacing
an integral indicator. (See Figure 9.4.2)
Removing the Integral Indicator
1) Remove the cover.
2) Supporting the integral indicator by hand, loosen its
two mounting screws.
3) Dismount the LCD board assembly from the CPU
assembly.
When doing this, carefully pull the LCD board
assembly straight forward so as not to damage the
connector pins between it and the CPU assembly.
Shrouding Bolt
Shrouding Bolt
F0902.EPS
Figure 9.4 Shrouding Bolts
9-3
IM 01C21C01-01E
9. MAINTENANCE
Attaching the Integral Indicator
Integral indicator can be installed in the following three
directions.
F0910.EPS
Figure 9.4.1 Installation Direction of Indicator
1) Align both the LCD board assembly and CPU
assembly connectors and engage them.
2) Insert and tighten the two mounting screws.
3) Replace the cover.
Output terminal cable
Press
forward
9.4.2 Replacing the CPU Board Assembly
This subsection describes the procedure for replacing
the CPU assembly. (See Figure 9.4.2)
Removing the CPU Assembly
1) Remove the cover. If an integral indicator is
mounted, refer to Subsection 9.4.1 and remove the
indicator.
2) Turn the zero-adjustment screw to the position
(where the screw head slot is horizontal) as shown
in Figure 9.4.2.
3) Disconnect the output terminal cable (cable with
brown connector at the end). When doing this,
lightly press the side of the CPU assembly connector and pull the cable connector to disengage.
4) Use a socket driver (width across flats, 5.5mm) to
loosen the two bosses.
5) Carefully pull the CPU assembly straight forward to
remove it.
6) Disconnect the flat cable (cable with black connector at the end) that connects the CPU assembly and
the capsule.
NOTE
LCD board
assembly
Be careful not to apply excessive force to the
CPU assembly when removing it.
Integral
indicator
Boss
Flat cable
CPU assembly
Zero-adjustment
Bracket
screw pin
(for zero-adjustment
screw pin)
Cover
Mounting
screw
Mounting the CPU Assembly
1) Connect the flat cable (with black connector)
between the CPU assembly and the capsule.
2) Connect the output terminal cable (with brown
connector).
F0903.EPS
NOTE
Figure 9.4.2 Removing and Attaching LCD Board Assembly and CPU Assembly
Make certain that the cables are free of pinching
between the case and the CPU assembly edge.
3) Align and engage the zero-adjustment screw pin
with the groove on the bracket on the CPU assembly. Then insert the CPU board assembly straight
onto the post in the amplifier case.
4) Tighten the two bosses. If the transmitter is
equipped with an integral indicator, refer to Subsection 9.4.1 to mount the indicator.
9-4
IM 01C21C01-01E
9. MAINTENANCE
9.5 Troubleshooting
NOTE
Confirm that the zero-adjustment screw pin is
placed properly in the groove on the bracket
prior to tightening the two bosses. If it is not, the
zero-adjustment mechanism will be damaged.
5) Replace the cover.
If any abnormality appears in the measured values, use
the troubleshooting flow chart below to isolate and
remedy the problem. Since some problems have
complex causes, these flow charts may not identify all.
If you have difficulty isolating or correcting a problem,
contact Yokogawa service personnel.
9.5.1 Basic Troubleshooting
9.4.3 Replacing the Process Connector
Gasket
This subsection describes the procedure for replacing
the process connector gasket. (See Figure 9.4.3.)
1) Loosen the two bolts and remove the process
connector.
2) Replace the process connector gasket.
3) Mount the process connector. Tighten the bolts
securely and uniformly to a torque of 39 to 49 N·m
{4 to 5 kgf·m}, and verify that there are no pressure
leaks.
First determine whether the process variable is actually
abnormal or a problem exists in the measurement
system.
If the problem is in the measurement system, isolate
the problem and decide what corrective action to take.
This transmitter is equipped with a self-diagnostic
function which will be useful in troubleshooting; see
Section 8.5 for information on using this function.
: Areas where self-diagnostic offers support
Abnormalities appear in measurement.
YES
Process connector
gasket
Is process variable
itself abnormal?
NO
Inspect the
process system.
Measurement system problem
Isolate problem in
measurement system.
Bolt
YES
Process connector
F0904.EPS
Figure 9.4.3 Replacing the Process Connector Gasket
Does problem exist in
receiving instrument?
NO
Inspect receiver.
Environmental conditions
Transmitter itself
Check/correct
environmental conditions.
Check transmitter.
Operating conditions
Check/correct operating
conditions.
F0905.EPS
Figure 9.5.1 Basic Flow and Self-Diagnostics
9-5
IM 01C21C01-01E
9. MAINTENANCE
9.5.2 Troubleshooting Flow Charts
Output travels beyond 0% or 100%.
The following sorts of symptoms indicate that transmitter
may not be operating properly.
Example : • There is no output signal.
• Output signal does not change even though
process variable is known to be varying.
• Output value is inconsistent with value
inferred for process variable.
Connect BRAIN TERMINAL and check self-diagnostics.
Does the selfdiagnostic indicate problem
location?
YES
Connect BRAIN TERMINAL and check self-diagnostics.
NO
Refer to error message summary in
Subsection 8.5.2 to take actions.
YES
Does the self-diagnostic
indicate problem location?
NO
Is power supply
polarity correct?
NO
Refer to error message summary in
Subsection 8.5.2 to take actions.
YES
Refer to Section 6.3 to check/correct
polarity at each terminal from power
supply to the terminal box.
NO
Is power supply
polarity correct?
NO
Are valves opened or
closed correctly?
YES
Refer to Section 6.3 to check/correct
polarity at each terminal from power
supply to the terminal box.
Are power
supply voltage and load
resistance correct?
YES
Fully open the low pressure valve.
NO
Is there any pressure leak?
YES
Refer to Section 6.6 for rated voltage
and load resistance.
NO
Fix pressure leaks, paying particular
attention to connections for impulse
piping, pressure-detector section, etc.
NO
Are valves opened or
closed correctly?
NO
Is zero point
adjusted correctly?
YES
Fully open the low pressure valve.
YES
F0907.EPS
Fix pressure leaks, paying particular
attention to connections for impulse
piping, pressure-detector section, etc.
Is there
continuity through the
transmitter loop wiring?
Do the loop numbers
match?
YES
Adjust the zero point.
Contact Yokogawa service personnel.
YES
Is there any pressure leak?
NO
YES
NO
Find/correct broken conductor or
wiring error.
Contact Yokogawa service personnel.
F0906.EPS
9-6
IM 01C21C01-01E
9. MAINTENANCE
Large output error.
Connect BRAIN TERMINAL and check self-diagnostics.
Does the selfdiagnostic indicate problem
location?
NO
YES
Refer to error message summary in
Subsection 8.5.2 to take actions.
NO
Are valves opened or
closed correctly?
YES
Fully open the low pressure valve.
NO
Is impulse piping
connected correctly?
YES
Refer to individual model user manuals
and connect piping as appropriate for
the measurement purpose.
NO
Are power supply
voltage and load resistance
correct?
YES
Refer to Section 6.6 for rated voltage
and load resistance.
Is transmitter
installed where there is
marked variation in
temperature?
NO
YES
Provide lagging and/or cooling, or allow
adequate ventilation.
Were appropriate
instruments used for
calibration?
YES
NO
Refer to Section 9.2 when selecting
instruments for calibration.
Is output adjusted correctly?
YES
NO
Adjust the output.
Contact Yokogawa service personnel.
F0908.EPS
9-7
IM 01C21C01-01E
10. GENERAL SPECIFICATIONS
10. GENERAL SPECIFICATIONS
10.1 Standard Specifications
Damping Time Constant (1st order):
The sum of the amplifier and capsule damping
time constant must be used for the overall time
constant. Amp damping time constant is adjustable
from 0.2 to 64 seconds.
Refer to IM 01C22T02-01E for FOUNDATION
Fieldbus communication type and IM 01C22T0300E for PROFIBUS PA communication type
marked with “䉫”.
EJA210A
䊉 Performance Specifications
Capsule (Silicone Oil)
See General Specifications sheet, GS 01C21C0100E.
Time Constant (approx. sec)
䊉 Functional Specifications
Span
M
Range
Span
H
Range
kPa
inH2O
(/D1)
1 to 100
4 to 400
–100
–400 to 400
to 100
mbar
(/D3)
5 to 500 20 to 2000 50 to 5000
–500
to 500
–2000
to 2000
mmH2O
(/D4)
–5000
to 5000
0.4
0.4
M
H
0.4 0.4
Process Temperature Limits:
* Safety approval codes may affect limits.
–40 to 120°C (–40 to 248°F)
10 to 1000 100 to 10000
–1000
to 1000
H
Ambient Temperature Limits:
* Safety approval codes may affect limits.
–40 to 85°C (–40 to 185°F)
–30 to 80°C (–22 to 176°F) with LCD Display
Span & Range Limits:
Measurement
Span
and Range
M
EJA220A
–10000
to 10000
Working Pressure Limits (Silicone Oil)
2.7 kPa abs (0.38 psia) to flange rating
(see Figure 1.)
0.05 to
5 kgf/cm2
–5 to
5 kgf/cm2
䊉 Installation
T1001.EPS
URL is define as the Upper Range Limit from the table
above.
Supply & Load Requirements “䉫”:
* Safety approvals can affect electrical requirements.
See Section 6.6, ‘Power Supply Voltage and Load
Resistance.’
Zero Adjustment Limits:
Zero can be fully elevated or suppressed, within
the Lower and Upper Range Limits of the capsule.
Supply Voltage “䉫”:
10.5 to 42 V DC for general use and flameproof type
10.5 to 32 V DC for lightning protector (Optional code/A)
10.5 to 30 V DC for intrinsically safe, Type n,
nonincendive, or non-sparking type
Minimum voltage limited at 16.4 V DC for digital
communications, BRAIN and HART
External Zero Adjustment “䉫”:
External zero is continuously adjustable with
0.01% incremental resolution of span. Span may
be adjusted locally using the digital indicator with
range switch.
Output “䉫”:
Two wire 4 to 20 mA DC output with digital
communications, linear or square root programmable. BRAIN or HART FSK protocol are superimposed on the 4 to 20 mA signal.
Failure Alarm:
Output status at CPU failure and hardware error;
Up-scale: 110%, 21.6 mA DC or more(standard)
Down-scale: -5%, 3.2 mA DC or less
-2.5%, 3.6 mA DC or less(Optional
code /F1)
,
EMC Conformity Standards“䉫”:
EN61326-1 Class A, Table 2 (For use in industrial
lications)
EN61326-2-3
Communication Requirements “䉫”:
BRAIN
Communication Distance;
Up to 2 km (1.25 miles) when using CEV polyethylene-insulated PVC-sheathed cables.
Communication distance varies depending on type
of cable used.
Load Capacitance;
0.22 µF or less (see note)
Load Inductance;
3.3 mH or less (see note)
Input Impedance of communicating device;
10 kΩ or more at 2.4 kHz.
Note: Applicable for Output signal code D and E
Note: For general-use and Flameproof type.
For Intrinsically safe type, please refer to
‘Optional Specifications.’
10-1
IM 01C21C01-01E
10. GENERAL SPECIFICATIONS
HART
Communication Distance;
Up to 1.5 km (1 mile) when using multiple twisted
pair cables. Communication distance varies
depending on type of cable used.
Use the following formula to determine cable
length for specific applications:
Atmospheric
pressure
100{14.5}
Working
pressure
kPa abs
{psi abs}
Applicable range
10{1.4}
65 x 106 (Cf + 10,000)
L=
C
(R x C)
Where:
L = length in meters or feet
R = resistance in Ω (including barrier resistance)
C = cable capacitance in pF/m or pF/ft
Cf = maximum shunt capacitance of receiving
devices in pF/m or pF/ft
2.7{0.38}
1{0.14}
-40
(-40)
0
(32)
40
(104)
80
(176)
120
(248)
Process temperature °C (°F)
F1001.EPS
䊉 Physical Specifications
Figure 1.
Wetted Parts Materials:
High side:
See ‘Model and Suffix Codes’
Low side:
Diaphragm;
Hastelloy C-276
Cover flange;
SCS14A
Process connector;
SCS14A
Capsule gasket;
Teflon-coated SUS316L
Drain/Vent plug;
SUS316
Process connector gasket;
PTFE Teflon
Non-wetted Parts Materials:
Bolting;
SCM435, SUS630, or SUH660
Housing;
Low copper cast-aluminum alloy with polyurethane
paint (Munsell 0.6GY3.1/2.0)
Degrees of Protection
IP67, NEMA4X, JIS C0920 immersion proof
Cover O-rings;
Buna-N
Data plate and tag;
SUS304 or SUS316 (optional)
Fill Fluid;
Silicone or Fluorinated oil (optional)
Weight:
EJA210A with 150# flange 11 kg(25 lb)
EJA220A with 150# flange 16 kg(35 lb)
Connections:
Refer to the ‘Model and Suffix Codes’ to specify
the process and electrical connection type.
The high pressure side is a flange connected, and
low side is threaded.
Working Pressure and Process Temperature
< Settings When Shipped > “䉫”
Tag Number
As specified in order *1
Output Mode
‘Linear’
Display Mode
‘Linear’
Operation Mode
‘Normal’ unless otherwise specified in order
Damping Time ‘2 sec.’
Constant
Calibration Range
Lower Range Value As specified in order
Calibration Range As specified in order
Higher Range Value
Selected from mmH2O, mmAq, mmWG,
Calibration Range mmHg, Pa, hPa, kPa, MPa, mbar, bar,
gf/cm2, kgf/cm2, inH2O, inHg, ftH2O, or psi.
Units
(Only one unit can be specified)
M1003.EPS
*1:
10-2
Up to 16 alphanumeric characters (including - and
· ) will be entered in the amplifier memory.
IM 01C21C01-01E
10. GENERAL SPECIFICATIONS
10.2 Model and Suffix Codes
Model EJA210A
Model
Suffix Codes
Description
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
EJA210A
Flange-mounted differential pressure transmitter
(Flush diaphragm type)
Output Signal
-D . . . . . . . . . . . . . . . . . . 4 to 20 mA DC with digital communication (BRAIN protocol)
-E . . . . . . . . . . . . . (Note 1) 4 to 20 mA DC with digital communication (HART protocol)
-F . . . . . . . . . . . . . (Note 5) Digital communication (FOUNDATION Fieldbus protocol)
-G . . . . . . . . . . . . . (Note 6) Digital communication (PROFIBUS PA protocol)
Measurement span
M . . . . . . . . . . . . . . . . . 1 to 100 kPa {100 to 10000 mmH2O}
(capsule)
H . . . . . . . . . . . . . . . . . . 5 to 500 kPa {0.05 to 5 kgf/cm2}
High pressure side
(Process flange side)
wetted parts material
(Note 2)
Process flange rating
Process flange
size/material
S . . . . . . . . . . . (Note 3)
H . . . . . . . . . . . (Note 3)
T . . . . . . . . . . . (Note 3)
W . . . . . . . . . . (Note 4)
J1 . . . . . . . . . . . . . .
J2 . . . . . . . . . . . . . .
A1 . . . . . . . . . . . . . .
A2 . . . . . . . . . . . . . .
P1 . . . . . . . . . . . . . .
P2 . . . . . . . . . . . . . .
D2 . . . . . . . . . . . . . .
D4 . . . . . . . . . . . . . .
D..............
E..............
F..............
A..............
B..............
C..............
Low pressure side process
connection
Bolts and nuts material
Installation
Electrical connection
Integral indicator
0.............
1.............
2.............
3.............
4.............
5.............
A...........
B...........
C...........
-9 . . . . . . . . . .
0.........
2.........
3.........
4.........
5.........
7.........
8.........
9.........
A........
C........
D........
D........
E........
N........
[Diaphragm]
SUS316L
Hastelloy C-276
Tantalum
Hastelloy C-276
[Others]
SUS316
Hastelloy C-276
Tantalum
SUS316
JIS10K
JIS20K
ANSI Class 150
ANSI Class 300
JPI Class150
JPI Class 300
DIN PN10/16
DIN PN25/40
3-inch (80 mm) /S25C
3-inch (80 mm) /SUS304
3-inch (80 mm) /SUS316
2-inch (50 mm) /SU25C
2-inch (50 mm) /SUS304
2-inch (50 mm) /SUS316
without process connector (Rc1/4 female on the cover flange)
with Rc1/4 female process connector
with Rc1/2 female process connector
with 1/4NPT female process connector
with 1/2NPT female process connector
without process connector (1/4 NPT female on the cover flange)
SCM435
SUS630
SUH660
Horizontal impulse piping type, left side high pressure
G1/2 female, one electrical connection
1/2 NPT female, two electrical connections without blind plug
Pg 13.5 female, two electrical connections without blind plug
M20 female, two electrical connections without blind plug
G1/2 female, two electrical connections and a blind plug
1/2 NPT female, two electrical connections and a blind plug
Pg 13.5 female, two electrical connections and a blind plug
M20 female, two electrical connections and a blind plug
G1/2 female, two electrical connections and a SUS316 blind plug
1/2 NPT female, two electrical connections and a SUS316 blind plug
M20 female, two electrical connections and a SUS316 blind plug
Digital indicator
Digital indicator with the range setting switch
(None)
N . . . . . . Always N
Optional codes
/ Optional specification
T1002.EPS
Example: EJA210A-DMSA1D5A-92NN/
Note 1: Refer to IM 01C22T01-01E for HART Protocol version.
Note 2: Low pressure side wetted parts material: Cover flange; SCS14A, Process connector; SCS14A,
Capsule; SUS316L (Diaphragm; Hastelloy C-276), Vent plug; SUS316
Note 3: Applicable only for 3-inch (80 mm) flange size (Process flange size/material codes D and E)
Note 4: Applicable only for 2-inch (50 mm) flange size (Process flange size/material codes A and B)
Note 5: Refer to IM 01C22T02-01E for Fieldbus communication.
Note 6: Refer to IM 01C22T03-00E for PROFIBUS PA communication.
10-3
IM 01C21C01-01E
10. GENERAL SPECIFICATIONS
Model EJA220A
Model
Suffix Codes
EJA220A
...................
Flange-mounted differential pressure transmitter
(Extended diaphragm type)
-D . . . . . . . . . . . . . . . . .
-E . . . . . . . . . . . . (Note 1)
-F . . . . . . . . . . . . (Note 5)
-G . . . . . . . . . . . (Note 6)
4 to 20 mA DC with digital communication (BRAIN protocol)
4 to 20 mA DC with digital communication (HART protocol)
Digital communication (FOUNDATION Fieldbus protocol)
Digital communication (PROFIBUS PA protocol)
Output Signal
Measurement span
(capsule)
High pressure side
(Process flange side)
wetted parts material
Description
M . . . . . . . . . . . . . . . . 1 to 100 kPa {100 to 10000 mmH2O}
H . . . . . . . . . . . . . . . . 5 to 500 kPa {0.05 to 5 kgf/cm2}
[Diaphragm]
[Pipe]
[Others]
SUS316 SUS316
S . . . . . . . . . . (Note 3) SUS316L
W . . . . . . . . . (Note 4) Hastelloy C-276 SUS316 SUS316
(Note 2)
J1 . . . . . . . . . . . .
J2 . . . . . . . . . . . . .
A1 . . . . . . . . . . . . .
A2 . . . . . . . . . . . . .
P1 . . . . . . . . . . . . .
P2 . . . . . . . . . . . . .
D2 . . . . . . . . . . . . .
D4 . . . . . . . . . . . . .
Diaphragm extension
2.............
length (X2)
4.............
6.............
Process flange
G...........
size/material
H...........
J...........
D...........
E...........
F...........
Low pressure side process
0 ..........
connection
1 ..........
2 ..........
3 ..........
4 ..........
5 ..........
Process flange rating
Bolts and nuts material
Installation
Electrical connection
Integral indicator
Optional codes
A.........
B.........
C.........
-9 . . . . . . .
0......
2......
3......
4......
5......
7......
8......
9......
A......
C......
D......
JIS10K
JIS20K
ANSI Class 150
ANSI Class 300
JPI Class 150
JPI Class 300
DIN PN10/16
DIN PN25/40
X2=50 mm
X2=100 mm
X2=150 mm
4-inch (100 mm) / S25C
4-inch (100 mm) / SUS304
4-inch (100 mm) / SUS316
3-inch (80 mm) / S25C
3-inch (80 mm) / SUS304
3-inch (80 mm) / SUS316
without process connector (Rc1/4 female on the cover flanges)
with Rc1/4 female process connector
with Rc1/2 female process connector
with 1/4 NPT female process connector
with 1/2 NPT female process connector
without process connector (1/4 NPT female on the cover flanges)
SCM435
SUS630
SUH660
Horizontal impulse piping type, left side high pressure
G1/2 female, one electrical connection
1/2 NPT female, two electrical connections without blind plug
Pg 13.5 female, two electrical connections without blind plug
M20 female, two electrical connections without blind plug
G1/2 female, two electrical connections and a blind plug
1/2 NPT female, two electrical connections and a blind plug
Pg 13.5 female, two electrical connections and a blind plug
M20 female, two electrical connections and a blind plug
G1/2 female, two electrical connections and a SUS316 blind plug
1/2 NPT female, two electrical connections and a SUS316 blind plug
M20 female, two electrical connections and a SUS316 blind plug
D . . . . . Digital indicator
E . . . . . Digital indicator with the range setting switch
N . . . . . (None)
N . . . . Always N
/ Optional specification
T1003.EPS
Example: EJA220A-DMSA12G5A-92NN/
Note 1: Refer to IM 01C22T01-01E for HART Protocol version.
Note 2: Low pressure side wetted parts material: Cover flange; SCS14A, Process connector; SCS14A,
Capsule; SUS316L (Diaphragm, Hastelloy C-276), Vent plug ; SUS316
Note 3: Applicable only for 4-inch (100 mm) flange size (Process flange size/material codes G and H).
Note 4: Applicable only for 3-inch (80 mm) flange size (Process flange size/material codes D and E).
Note 5: Refer to IM 01C22T02-01E for Fieldbus communication.
Note 6: Refer to IM 01C22T03-00E for PROFIBUS PA communication.
10-4
IM 01C21C01-01E
10. GENERAL SPECIFICATIONS
10.3 Optional Specifications
For FOUNDATION Fieldbus explosion protected type, see IM 01C22T02-01E.
For PROFIBUS PA explosion protected type, see IM 01C22T03-00E.
Item
Description
Factory Mutual (FM)
CENELEC ATEX
Code
FM Explosionproof Approval *1
Explosionproof for Class I, Division 1, Groups B, C and D
Dust-ignitionproof for Class II/III, Division 1, Groups E, F and G
Hazardous (classified) locations, indoors and outdoors (NEMA 4X)
Temperature class: T6
Amb. Temp.: –40 to 60C (–40 to 140F)
FF1
FM Intrinsically safe Approval *1
Intrinsically Safe for Class I, Division 1, Groups A, B, C & D, Class II, Division 1,
Groups E, F & G and Class III, Division 1 Hazardous Locations.
Nonincendive for Class I, Division 2, Groups A, B, C & D, Class II, Division. 2,
Groups E, F & G, and Class III, Division 1 Hazardous Locations.
Enclosure: “NEMA 4X”, Temp. Class: T4, Amb. Temp.: –40 to 60C (–40 to 140F)
Intrinsically Safe Apparatus Parameters
[Groups A, B, C, D, E, F and G]
Vmax=30 V, Imax=165 mA, Pmax=0.9 W, Ci=22.5 nF, Li=730 H
[Groups C, D, E, F and G]
Vmax=30 V, Imax=225 mA, Pmax=0.9 W, Ci=22.5 nF, Li=730 H
FS1
Combined FF1 and FS1 *1
FU1
CENELEC ATEX (KEMA) Flameproof Approval *2
Certificate: KEMA 02ATEX2148
II 2G EExd IIC T4, T5, T6
Amb. Temp.: T5; –40 to 80C ( –40 to 176F), T4 and T6; –40 to 75C ( –40 to 167F)
Max. process Temp.: T4; 120C (248F), T5; 100C (212F), T6; 85C (185F)
KF2
CENELEC ATEX (KEMA) Intrinsically safe Approval *2
Certificate: KEMA 02ATEX1030X
II 1G EEx ia IIC T4, Amb. Temp.: –40 to 60C (–40 to 140F)
Ui=30 V, Ii=165 mA, Pi=0.9 W, Ci=22.5 nF, Li=730 H
KS2
Combined KF2, KS2 and Type n *2
Type n
II 3G Ex nL IIC T4, Amb. Temp.: –40 to 60°C (–40 to 140°F)
Ui=30 V DC, Ci=22.5 nF, Li=730 µH
Dust
II 1D maximum surface temperature T65°C (149F) {Tamb.: 40°C (104F)},
T85°C (185F) {Tamb.: 60°C (140F)}, T105°C (221F) {Tamb.: 80°C (176F)}
KU2
T1004-1.EPS
*1:
*2:
Applicable for Electrical connection code 2 and 7 (1/2 NPT female).
Applicable for Electrical connection code 2, 4, 7 and 9 (1/2 NPT and M20 female).
10-5
IM 01C21C01-01E
10. GENERAL SPECIFICATIONS
Item
Canadian Standards
Association (CSA)
IECEx
Scheme
Description
Code
CSA Explosionproof Approval *1
Certificate: 1089598
Explosionproof for Class I, Division 1, Groups B, C and D
Dustignitionproof for Class II/III, Division 1, Groups E, F and G
Division2 ‘SEALS NOT REQUIRED’ , Temp. Class: T4, T5, T6 Encl Type 4x
Max. Process Temp.: T4; 120C (248F), T5; 100C (212F), T6; 85C (185F)
Amb. Temp.: –40 to 80C (–40 to 176F)
Process Sealing Certification
Dual Seal Certified by CSA to the requirement of ANSI/ISA 12.27.01
No additional sealing required. Primary seal failure annunciation: at the zero
adjustment screw
CF1
CSA Intrinsically safe Approval *1
Certificate: 1053843
Intrinsically Safe for Class I, Groups A, B, C and D Class II and III, Groups E, F and G
Nonincendive for Class I, Division 2, Groups A, B, C and D Class II, Division 2,
Groups F and G and Class III (not use Safety Barrier)
Encl Type 4x, Temp. Class: T4, Amb. Temp.: –40 to 60C (–40 to 140F)
Vmax=30 V, Imax=165 mA, Pmax=0.9 W, Ci=22.5 nF, Li=730 H
Process Sealing Certification
Dual Seal Certified by CSA to the requirement of ANSI/ISA 12.27.01
No additional sealing required. Primary seal failure annunciation: at the zero
adjustment screw
CS1
Combined CF1 and CS1 *1
CU1
IECEx Intrinsically safe, type n and Flameproof Approval *2
Intrinsically safe and type n
Certificate: IECEx KEM 06.0007X
Ex ia IIC T4, Ex nL IIC T4 Enclosure: IP67
Amb. Temp.: –40 to 60C (–40 to 140F), Max. Process Temp.: 120C (248F)
Electrical Parameters: [Ex ia] Ui=30 V, Ii=165 mA, Pi=0.9 W, Ci=22.5 nF, Li=730 H
[Ex nL] Ui=30 V, Ci=22.5 nF, Li=730 H
Flameproof
Certificate: IECEx KEM 06.0005
Ex d IIC T6...T4 Enclosure: IP67
Max.Process Temp.: T4;120C (248F), T5;100C (212F), T6; 85C (185F)
Amb.Temp.: –40 to 75C (–40 to 167F) for T4, –40 to 80C (–40 to 176F) for T5,
–40 to 75C (–40 to 167F) for T6
SU2
T1004-2.EPS
*1:
*2:
Applicable for Electrical connection code 2 and 7 (1/2 NPT female).
Applicable for Electrical connection code 2, 4 and 7 (1/2 NPT and M20 female).
10-6
IM 01C21C01-01E
10. GENERAL SPECIFICATIONS
Item
Description
Code
Amplifier cover only
P
Amplifier cover and terminal cover, Munsell 7.5 R4/14
PR
Epoxy resin-baked coating
X1
316 SST exterior parts
Exterior parts on the amplifier housing (name plates, tag plate, zero-adjustment screw,
stopper screw) will become 316 or 316L SST.
HC
Lightning protector
Transmitter power supply voltage: 10.5 to 32 V DC (10.5 to 30 V DC for intrinsically safe
type, 9 to 32 V DC for FOUNDATION Fieldbus and PROFIBUS PA communication type.)
Allowable current: Max. 6000 A (1ⴛ40 µs ), Repeating 1000 A,100 times
A
Painting
Color change
Coating change
Oil-prohibited use
Oil-prohibited use
with dehydrating treatment
Degrease cleansing treatment
K1
Degrease cleansing treatment with fluorinated oil filled capsule.
Operating temperature –20 to 80 °C
K2
Degrease cleansing and dehydrating treatment
K5
Degrease cleansing and dehydrating treatment with fluorinated oil filled capsule.
Operating temperature –20 to 80 °C
K6
P calibration (psi unit )
D1
( See Table for Span
and Range Limits. )
bar calibration (bar unit )
Calibration units
M calibration ( kgf/cm2 unit )
D3
D4
Sealing treatment to
SUS630 nuts
Sealant ( liquid silicone rubber )
No serration
No serration work on the flange gasket surface ( for ANSI flange only )
Y
Q
kgf/cm2}
Teflon film
With FEP film and fluorinated oil. Working range: 20 to 120 °C, 0 to 2 MPa {0 to 20
(Not usable under vacuum )
Fast response *2
Update time: 0.125 sec or less, see GS for response time
F1
Failure alarm down-scale *1
Output status at CPU failure and hardware error is –5%, 3.2 mA or less.
C1
Output signal limits:
3.8 mA to 20.5 mA
NAMUR NE43 compliant *1
T
Failure alarm down-scale: output status at CPU failure and
hardware error is –5%, 3.2 mA or less.
C2
Failure alarm up-scale: output status at CPU failure and
hardware error is 110%, 21.6 mA or more.
C3
Stainless steel amplifier
housing
Amplifier housing material: SCS14A stainless steel
(equivalent to SUS316 cast stainless steel or ASTM CF-8M)
E1
Gold-plate
Gold-plated diaphragm for high pressure side (process flange side)
A1
Stainless steel tag plate
JIS SUS304 stainless steel tag plate wired onto transmitter
N4
High pressure side: Process flange, Block
Low pressure side: Cover flange
High pressure side: Process flange, Block
Low pressure side: Cover flange, Process connector
Mill Certificate
High pressure side: Process flange, Block, Pipe, Base
Low pressure side: Cover flange
High pressure side: Process flange, Block, Pipe, Base
Low pressure side: Cover flange, Process connector
Pressure test/
Leak test
Certificate
( Flange rating )
( Test Pressure )
JIS 10K
2MPa {20 kgf/cm2 }
JIS 20K
5MPa {50
kgf/cm2 }
ANSI/JPI class 150
3MPa {29.8 kgf/cm2 }
kgf/cm2
ANSI/JPI class 300
7.7MPa {77
ANSI/JPI class 300
7MPa {70 kgf/cm2 }
For
model
EJA210A
M03
For
model
EJA220A
M04
M13
M14
T31
T32
}
Nitrogen ( N2 ) Gas
T36
Retention time: 10 minutes
T37
T38
T1005.EPS
* 1:
* 2:
Applicable for Output signal code D and E. The hardware error indicates faulty amplifier or
capsule. When combining with Optional code F1, output status for down-scale is –2.5%,
3.6 mA DC or less.
Applicable for Output signal code D and E. Write protection switch is attached for Output code E.
10-7
IM 01C21C01-01E
10. GENERAL SPECIFICATIONS
10.4 Dimensions
Model EJA210A
174 (6.85)
External indicator
conduit connection
Blind plug
(Optional)
25
(0.98)
30 (1.18)
133 (5.24)
110 (4.33)
Zero
adjustment
Conduit
connection
Terminal side
Internal
indicator
(Optional)
t
35
(1.38)
ø78
(3.07)
163
(6.42)
146
(5.75)
Ground
terminal
Shrouding bolt *2
øD øC øg ød
*1
Vent plug
46
(1.81)
Drain plug
Process
connector
(Optional)
n- øh
54
(2.13)
Process flange
*1 Indicates inside diameter of gasket contact surface.
*2 Applicable only for ATEX and IECEx Flameproof type.
Flange size: 3-inch (80 mm)
Flange Nominal
Diameter and
Rating
øD
øC
øg
ød
t
Bolt Holes
No.(N)
Dia.(øh)
80 mm JIS 10K
185(7.28) 150(5.91) 130(5.12) 90(3.54)
18(0.71)
8
19(0.75)
80 mm JIS 20K
200(7.87) 160(6.30) 130(5.12) 90(3.54)
22(0.87)
8
23(0.91)
3-inch ANSI Class150 190.5(7.50) 152.4(6.00) 130(5.12) 90(3.54) 23.9(0.94)
4
19.1(0.75)
3-inch ANSI Class300 209.6(8.25) 168.1(6.62) 130(5.12) 90(3.54) 28.5(1.12)
8
22.4(0.88)
3-inch JPI Class150
190(7.48) 152.4(6.00) 130(5.12) 90(3.54)
4
19(0.75)
3-inch JPI Class300
210(8.27) 168.1(6.62) 130(5.12) 90(3.54) 28.5(1.12)
8
22(0.87)
3-inch DIN PN 10/16
200(7.87)
160(6.30)
130(5.12) 90(3.54)
20(0.79)
8
18(0.71)
3-inch DIN PN 25/40
200(7.87)
160(6.30)
130(5.12) 90(3.54)
24(0.44)
8
18(0.71)
24(0.44)
Flange size: 2-inch (50 mm)
Flange Nominal
Diameter and
Rating
øD
øC
øg
ød
t
Bolt Holes
No.(N)
Dia.(øh)
50 mm JIS 10K
155(6.10) 120(4.72) 100(3.94) 61(2.40)
16(0.63)
4
19(0.75)
50 mm JIS 20K
155(6.10) 120(4.72) 100(3.94) 61(2.40)
18(0.71)
8
19(0.75)
2-inch ANSI Class150 152.4(6.00) 120.7(4.75) 100(3.94) 61(2.40) 19.1(0.75)
4
19.1(0.75)
2-inch ANSI Class300 165.1(6.50) 127(5.00) 100(3.94) 61(2.40) 22.4(0.88)
8
19.1(0.75)
2-inch JPI Class150
152(5.98) 120.6(4.75) 100(3.94) 61(2.40) 19.5(0.71)
4
19(0.75)
2-inch JPI Class300 165.1(6.50) 127(5.00) 100(3.94) 61(2.40) 22.5(0.89)
8
19(0.75)
2-inch DIN PN 10/16
165(6.50)
125(4.92)
100(3.94) 61(2.40)
18(0.71)
4
18(0.71)
2-inch DIN PN 25/40
165(6.50)
125(4.92)
100(3.94) 61(2.40)
20(0.79)
4
18(0.71)
F1003.EPS
10-8
IM 01C21C01-01E
10. GENERAL SPECIFICATIONS
Model EJA220A
30 (1.18)
174 (6.85)
External indicator
conduit connection
Blind plug
(Optional)
133 (5.24)
110 (4.33)
Zero
adjustment
Conduit
connection
35
(1.38)
Terminal side
Internal
indicator
(Optional)
ø78
(3.07)
163
(6.42)
146
(5.75)
Ground
terminal
1
Shrouding bolt *
øD øC øg
øA
Process
connection
46
(1.81)
Vent plug
Drain plug
Process
connector
(Optional)
n- øh
54
(2.13)
Process flange
t
25 (0.98)
X2
*1 Applicable only for ATEX and IECEx Flameproof type.
Flange size: 4-inch (100 mm)
Flange Nominal
Diameter and
Rating
øD
øC
øg
øA
t
Bolt Holes
No.(N) Dia.(øh)
100 mm JIS 10K
210(8.27) 175(6.89) 155(6.10) 96(3.78)
18(0.71)
8
19(0.75)
100 mm JIS 20K
225(8.86) 185(7.28) 155(6.10) 96(3.78)
24(0.94)
8
23(0.91)
4-inch ANSI Class150 228.6(9.00) 190.5(7.50) 155(6.10) 96(3.78) 23.9(0.94)
8
19.1(0.75)
4-inch ANSI Class300 254(10.00) 200(7.87) 155(6.10) 96(3.78) 31.8(1.25)
8
22.4(0.88)
4-inch JPI Class150
229(9.02) 190.5(7.50) 155(6.10) 96(3.78)
24(0.94)
8
19(0.75)
4-inch JPI Class300 254(10.00) 200.2(7.88) 155(6.10) 96(3.78)
32(1.26)
8
22(0.87)
4-inch DIN PN 10/16
220(8.66) 180(7.09) 155(6.10) 96(3.78)
20(0.79)
8
18(0.71)
4-inch DIN PN 25/40
235(9.25) 190(7.50) 155(6.10) 96(3.78)
24(0.94)
8
22(0.87)
Flange size: 3-inch (80 mm)
Flange Nominal
Diameter and
Rating
øD
øC
øg
øA
t
Bolt Holes
No.(N) Dia.(øh)
80 mm JIS 10K
185(7.28) 150(5.91) 130(5.12) 71(2.80)
18(0.71)
8
80 mm JIS 20K
200(7.87) 160(6.30) 130(5.12) 71(2.80)
19(0.75)
22(0.87)
8
23(0.91)
3-inch ANSI Class150 190.5(7.50) 152.4(6.00) 130(5.12) 71(2.80) 23.9(0.94)
4
19.1(0.75)
3-inch ANSI Class300 209.6(8.25) 168.1(6.62) 130(5.12) 71(2.80) 28.5(1.12)
8
22.4(0.88)
4
19(0.75)
3-inch JPI Class150
190(7.48) 152.4(6.00) 130(5.12) 71(2.80)
3-inch JPI Class300
210(8.27) 168.1(6.62) 130(5.12) 71(2.80) 28.5(1.12)
8
22(0.87)
3-inch DIN PN 10/16
200(7.88)
160(6.30) 130(5.12) 71(2.80)
20(0.79)
8
18(0.71)
3-inch DIN PN 25/40
200(7.87)
160(6.30) 130(5.12) 71(2.80)
24(0.94)
8
18(0.71)
24(0.94)
Diaphragm Extension Length Code
X2
2
1.97 inch (50 mm)
4
3.94 inch (100 mm)
6
5.91 inch (150 mm)
F1004.EPS
10-9
IM 01C21C01-01E
Customer
Maintenance
Parts List
DPharp EJA Series
Transmitter Section
2
5
4
11
A
10
3
12
13
1
2
2
1
14
A
6
7-2
7-1
Item
Part No.
Qty
1
Bellow
F9341RA
F9341RJ
F9341JP
Below
2
2
3
2
1
6
7-1
7-2
8
9
F9341AR
—
Bellow
F9900RG
F9900RR
F9341KL
Below
F9342AB
F9342AL
F9342AF
F9342AM
F9342BF
F9342BG
F9900RP
Y9612YU
9
Description
Cover
Cast-aluminum alloy
SCS14A stainless steel
O-ring
Case Assembly (Note 1)
Cast-aluminum alloy for G1/2
Cast-aluminum alloy for G1/2 (two electrical connections)
Cast-aluminum alloy for 1/2 NPT (two electrical connections)
Cast-aluminum alloy for M20 (two electrical connections)
Cast-aluminum alloy for Pg13.5 (two electrical connections)
F9341AA
F9341AC
F9341AE
F9341AH
F9341AJ
4
5
8
1
4
1
1
1
2
2
SCS14A stainless steel for 1/2 NPT (two electrical connections)
Name Plate
Screw
For cast-aluminum alloy case assembly
For SCS14A stainless steel case assembly
Tag Plate
CPU Assembly
For BRAIN protocol version
For HART protocol version
For BRAIN protocol version(Optional code /F1)
For HART protocol version with write protection switch (Optional code /F1)
For FOUNDATION Fieldbus protocol version
For FOUNDATION Fieldbus protocol version with PID/LM function (Optional code /LC1)
Cap Screw
Screw
10
Below
F9340NW
F9340NX
G9330DP
G9612EB
1
Plug
For Pg13.5
For M20
For G1/2
For 1/2 NPT
11
Bellow
F9341FM
F9341FJ
Below
F9342BL
1
Cover Assembly
Cast-aluminum alloy
SCS14A stainless steel
LCD Board Assembly
Without range-setting switch
12
13
14
F9342BM
F9342MK
F9300PB
5
1
2
2
For integral indicator
With range-setting switch
Mounting Screw
Label
(Note 1) Applicable for BRAIN and HART protocol versions (Output signal code D and E). For FOUNDATION Fieldbus protocol
version (Output signal code F), consult Yokogawa local office.
All Rights Reserved, Copyright © 1997, Yokogawa Electric Corporation.
Subject to change without notice. Printed in Japan.
Yokogawa Electric Corporation
CMPL 01C21A01-02E
11th Edition: Oct. 2008(KP)
Customer
Maintenance
Parts List
Model EJA210A and EJA220A
Flange Mounted Differential
Pressure Transmitter
(Pressure-detector Section)
EJA210A
EJA220A
1
8
5
3
9
4
2
Item
1
2
Part No.
3
F9300AJ
Below
D0114RB
U0102XC
Below
4
F9340XY
F9340XW
F9340XZ
F9340XX
Below
5
6
7
8
9
10
(Note 1)
X0100MN
F9273DZ
F9340AZ
Below
F9340SA
F9340SB
D0114PB
Below
F9200CS
D0114RZ
Below
F9275EC
F9275ED
F9275EE
Y9625YU
10
Qty
1
1
6
7
Description
1
O-Ring
Gasket
PTFE Teflon
PTFE Teflon (degreased)
Process Connector, SCS14A Stainless Steel (Note 1)
2
Rc 1/4
Rc 1/2
1/4 NPT
1/2 NPT
Bolt
1
1
1
1
1
2
SCM435 Chrome Molybdenum Steel
SUS630 Stainless Steel
SUH660 Stainless Steel
Vent Plug, SUS316 Stainless Steel
R 1/4
1/4 NPT
Vent Screw, SUS316 Stainless Steel
Drain Plug, SUS316 Stainless Steel (Note 1)
R 1/4
1/4 NPT
Vent Plug (degreased), SUS316 Stainless Steel
R 1/4
1/4 NPT
Needle Assembly (degreased), SUS316 Stainless Steel
Bolt
In case of degrease cleansing treatment (Optional Code/K1, K2, K5 and K6), consult YOKOGAWA local office.
All Rights Reserved, Copyright © 1997, Yokogawa Electric Corporation.
Subject to change without notice. Printed in Japan.
Yokogawa Electric Corporation
CMPL 01C21C01-01E
4th Edition: July 2001(YK)
REVISION RECORD
Title: Model EJA210A, EJA220A Flange Mounted Differential Pressure Transmitter
Manual No.: IM 01C21C01-01E
Edition
Date
Page
1st
Jun. 1997
–
2nd
Mar. 1998
CONTENTS
1-1
6-1
11-1
11-3
11-6
2-9+
CMPL
3rd
Sep. 1998
–
2-13
8-17
11-3
11-4
CMPL
4th
Oct. 1999
-
2-8
8-4
CMPL
5th
Sep. 2000
2-8
2-9
8-5
10-2
10-3
10-4
10-5
10-6
CMPL
6th
July 2001
2-10
8-4, 8-5
CMPL
Revised Item
New publication
Page 3
1
• Add REVISION RECORD.
• Add ‘NOTE’ notice for FOUNDATION Fieldbus and HART
protcol versions.
6.1
• Add Item to the Wiring Precautions.
11.1
• Add FOUNDATOIN Fieldbus protocol.
11.2
• Add Output signal code F.
11.3
• Add Optional code A1.
• Change the figure of terminal configuration.
CMPL 1C21A1-02E 1st
2nd
Page 2
• Add item 7-2.
Changed to Electronic File Format.
2.10
• Delete EMC Conformity Standards Tables.
8.3.2(9)
• Correction made in BURN OUT figure.
11.2
• Add Process flange size / material code F and C.
• Add Electrical connection code 7, 8, and 9.
• Add Process flange size / material code F and J.
• Add Electrical connection code 7, 8, and 9.
CMPL 1C21A1-02E 2nd
3rd
Page 2
• Add Part No. to Item 3 (For PG13.5 and M20).
• Add Part No. to Item 10 (For 1/2NPT, PG13.5, and M20).
Revised a book in a new format.
(The location of contents and the associated page numbers may
not coincide with the one in old editions.)
2.10
• Add AS/NZS 2064 1/2 to EMI, EMC Conformity Standards.
8.3.1
• Move Parameter Summary table to Chapter 8.
CMPL 1C21A1-02E 3rd
4th
• Change a format.
CMPL 1C21C1-01E 1st
2nd
• Change a format.
2.9.4b
2.9.4b
8.3.1
10.1
10.2
• Change contents of NOTE 1.
• Change contents of NOTE 4.
• Add footnote 2 and 3.
• Add calibration units of Pa and hPa.
• Add Bolts and nuts material code C.
• Add Bolts and nuts material code C.
10.3
• Add Amb. Temp. for T6: –40 to 75°C
• Add Optional code /F1 and /N4.
CMPL 1C21A1-02E 4th
5th(Manual Change)
• Add part numbers to 7-1 CPU Assembly.
F9342AF and F9342AM
CMPL 1C21A1-02E 5th
6th
• Add part numbers to 7-2 CPU Assembly.
F9342BG
• Change part number of 7-1 CPU Assembly.
F9342BC → F9342BB
• Change part number of 10 Plug
G9330DK → G9330DP
CMPL 1C21C1-01E 2nd
3rd
• Add part number to 4 Bolt.
F9340AZ
2.10
8.3.1
• Change EMC Conformity number.
• Add footnote (*4) to B40, Maximum static pressure in Parameter
Summary.
CMPL 1C21A1-02E 6th
7th(Manual Change)
• Change Part No. of 7-1 CPU Assembly for BRAIN protocol.
F9342BB → F9342AB
REVISION RECORD.EPS
IM 01C21C01-01E
Edition
Date
Page
6th
(Continued)
July 2001
CMPL
7th
May 2002
1-2
2-7
10-5
10-6
1.1
2.9.4
10.3
• Add “1.1 For Safety Using.”
• Add descriptions based on ATEX directive.
• Add Optional code K䊐2.
• Add Optional code C2 and C3.
8th
Apr. 2003
2-8
2-10
10-5
2.9.4
2.11
10.3
• Add Option code KU2.
• Add PED (Pressure Equipment Directive).
• Add Option code KU2.
9th
Apr. 2006
1-2
1-3
2-6
2-11
10-5, 10-6
10-6
10-7
1.1
1.3
2.9.3
2.12
10.3
• Add (e) Explosion Protected Type Instrument and (f) Modification
• Add “1.3 ATEX Document”
• Add “IECEx Certification” and delete “SAA Certification”
• Add Low Voltage Directive
• Add Certificate numbers and Applicable standards
• Add option code /SU2 and delete option code /SU1
• Add option code /PR
10th
Jan. 2008
1-1
1-4
2-3+
2-10
4-2
8-14
9-3
10-1+
10-5, -6
CMPL
11th
Oct. 2008
2-9
2-10
8-4 and 8-5
8-6
8-9 and later
8-18
9-1
9-5
10-3, 10-4
10-6, 10-7
CMPL
Revised Item
CMPL 1C21A1-02E 7th
8th(Manual Change)
• Change Part No. of 7-1 CPU Assembly for HART protocol.
F9342BH → F9342AL
CMPL 1C21A1-02E 8th
CMPL 01C21A01-02E 9th
• Delete Part No. of 4 Name Plate.
• Change Part No. of 5 Screw.
F9303JU → Y9303JU
CMPL 1C21C1-01E 3rd
CMPL 01C21C01-01E 4th
• Add direct current symbol.
• Add 11 European languages for ATEX documentation.
2.9.1
• Add applicable standard and certificate number for appovals.
2.10
• Add EMC caution note.
4.4
• Add section of changing the direction of integral indicator.
8.3.3 (12) • Add figure for A40.
9.4.1
• Add figure of integral indicator direction.
10.1, 10.2 • Add PROFIBUS PA communication type.
10.3
• Delete applicable standard from the table.
CMPL 01C21A01-02E 9th
CMPL 01C21A01-02E 10th
• Delete logo from the tag plate.
2.9.4
2.10
8.3.1
8.3.2
8.3.3
Change explosion protection marking for type n from EEx to Ex.
Update EMC conformity standards.
Add new parameters.
Add items in table 8.3.1.
Add (5) Change Output Limit and (14) Span Adjustment.
Re-number the items.
8.5.2
Modify descriptions and notes for Er.01.
9.3
Add a note for calibration.
9.4.3
Add a note for cleaning.
10.2
Add new suffix codes.
10.3
Add sealing statement for CSA.standards. Add /HC.
CMPL 01C21A01-02E 10th
11th
Change part No .of item 5 and 8.
REVISION RECORD.EPS
IM 01C21C01-01E
">