4 IN 1 CRIB
Read all instructions before assembly and use.
KEEP INSTRUCTIONS FOR FUTURE USE.
ADULT ASSEMBLY REQUIRED
Due to the presence of small parts during assembly,keep out of reach of children until assembly is complete.
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
Consumer Care:
www.dreamonme.com
1532 S WASHINGTON AVE
PISCATAWAY TWP NJ 08854
OFFICE: 732-752-7220
CUSTOMER SERVICE: 732-366-1788
style #: 633
MFG date: Sep 2017
When contacting Dream On Me you will need to reference the above numbers .They can also be found on the label on the Crib End bottom rail.
To register your product for important safety alerts and updates to your product please visit www.dreamonme.com and click on Product Registration.
1
CAUTION:
ANY MATTRESS USED IN THIS CRIB SHALL BE AT
LEAST 23 3/4 BY 37 3/4 IN. WITH A THICKNESS NOT
EXCEEDING 2 IN.
.
WARNING:
.
.
.
Infants can suffocate on soft bedding.Never add a pillow or comforter.Never place additional padding under an infant.
Failure to follow these warnings and the assembly instructions could result inserious injury or death.
DO NOT use this crib if you cannot exactly follow the accompanying instructions.
To reduce the risk of SIDS,pediatricians recommend healthy infants be placedon their backs to sleep, unless otherwise advised by your physician.
Strangulation Hazard:STRINGS CAN CAUSE STRANGULATION! Do not place items with a string around a child’s neck, such as hood strings or pacifier cords. Do not suspend strings over a crib or attach strings to toys. Strangulation Hazard: To help prevent strangulation tighten all fasteners.A child can trap parts of the body or clothing on loose fasteners.
.
.
Strangulation Hazard: Do not place crib near window or patio door where cords from blinds or drapes may strangle a child.
Fall Hazard: When child is able to pull to a standing position, set mattress to lowest position and remove bumper pads, large toys and other objects that could serve as steps for climbing out.This crib has an sdjustable mattress support For the convenience of the parent when the baby is very small, the mattress support may be used in the highest position.Important: with the mattress support and mattress in the highest position, be absolutely sure that the top of the front crib side is at least 3 inches higher then the top surface of the mattress.If it is not, lower the mattress support and the mattress to the next h ighest position.
.
.
.
.
.
.
.
.
.
Fall Hazard: Stop using crib when child begins to climb out or reaches s height of 35in(89), whichever occurs first. The child should be placed in a youth or regular bed.
.
Check this product for damagde hardware, loose joints,loose bolts or other fasteners,missing parts, or sharp edges before and after assembly and frequently during use.Securdly tighten loose bolts and other fasteners. Do not use crib if any parts are missing,damagde or broken.Contact Dream
On Me Inc for replacement parts and instructional literature if needed.Do not substitute parts.
Follow warnings on all products in a crib.
If refinishing,use a non-toxic finish specified for children’s products.
Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
Infants can suffocate in gaps between crib sides and a mattress that is too small.
Ensure a safe environment for the child by checking regularly, before placing the child in the crib,that every component is properly and securely in place.
To avoid head injury, do not allow any child to play underneath the crib.
Never add an accessory such as a bassinet or changing table that extends over the sleeping area.
In Canada Only-Use a crib mattress that is no thicker than 15 cm and is of such a size that,when it is pushed firmly against any side of the crib, it does not leave a gap of more than 3 cm between the mattress and any part of the sides of the crib. Do not use this crib for a child who can climb out of it or who is taller than 90 cm.
2
.
.
NOTES ON ASSEMBLY:
During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on the diagram of the item which is drawn actual size and design.Be sure to use the proper size and shape specified in the instructions.
To assemble this unit you may be required to place the unit on it’s side and face. It is strongly recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
NOTES ON USE:
Keep children and others safe by following these simple rules:
Do not allow any child to play on furniture.
Do not allow climbing on any piece of furniture.
Do not allow hanging from any piece of furniture.
Always monitor your child’s activity when in the nursery.
NOTES ON CARE AND MAINTENANCE:
Do not scratch or chip the finish.
Inspect the product periodically, contact Dream On Me for replacement parts or questions.
a damp, cold basement. These extremes can cause a loss of structural integrity.
To preserve the luster of the high quality finish on your product, it is recommended to place a doily or felt pad under any items you place on the finish.
Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.
Do not use abrasive chemicals.
Do not spray cleaners directly onto furniture.
Lift slightly when moving on carpeting to prevent leg breakage.
Use of a vaporizer near furniture will cause wood to swell and finish to peel.
Replace teething rail if damaged,cracked,or loose.
The Product,including side rails,must be fully erected prior to use.
Child can become entrapped and die when improvised netting or covers are placed on top of a play yard.Never add such items to confine child in play yard.
Always provide the supervision necessary for the continued safety of your child.When used for playing,never leave child unattended.
Never use a water mattress with this product.
3
=
4
PARTS:
MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT.
A. End Top Rail (2PCS) B. Front Rail (1PC) C. Left Front
Leg (1PC)
D. Right Front
Leg (1PC)
E. Left Back
Rail Leg (1PC)
F. Right Back Rail Leg (1PC) G. Back Rail (1PC) H. Left Crib End Bottom(1PC)
I. Right Crib End Bottom(1PC) J. Wooden Mattress Base (1PC) K. Mattress (1PC)
POUCH ATTACHED TO MATTRESS SUPPORT
-KEEP INSTRUCTIONS IN THIS POUCH
AFTER ASSEMBLY.
WARNINGS RELATED TO THE SAFE USE OF
THIS CRIB ARE PRINTED ON THE POUCH.
5
PARTS:
a.3” Allen head Bolt (6pcs)
No drills necessary.
Do not use power screwdriver
Phillips Screwdriver
(not supplied) d.3/4” Allen head Bolt (4pcs) e.Nuts (4pcs) f. Barrel nuts (16pcs) g. Metal connection (4pcs) i. Allen Wrench(1pc) j.3-3/8” Allen head Bolt (2pcs)
6
SECTION 1: Crib Assembly
STEP 1
Parts and tools required to complete step.
A. End Top Rail (2PCS) C. Left Front
Leg (1PC)
D. Right Front
Leg (1PC)
H. Left Crib End
Bottom(1PC) b.2-3/8” Allen head bolt (2pcs)
I. Right Crib End Bottom(1PC) f. Barrel nuts (4pcs) i. Allen Wrench (1pc)
Attach crib end top rail(A) to left front leg(C) using
1-3/8’’ allen head bolts (c) and left crib end bottom rails (H) to left front leg (C)) using 2-3/8’’ allen head bolts (b) &barrel nuts(f).; attach crib end top rail(A) to right front leg(D)
using 1-3/8’’ allen head bolts (c) and right crib end bottom rail(I) to right front leg(D) using 2-3/8’’ allen head bolts (b) &barrel nuts(f).
NOTE:
AFTER ASSEMBLY, THE “STEPPED HOLES”
IN BOTH POSTS ARE ON THE SAME SIDE.
I au
1
A et c et et
Left
H
A f f
C b c b
I
Right
A f
D b c f b
7
SECTION 1: Crib Assembly
STEP 2
Parts and tools required to complete step.
Left
From Step 1
Right
E. Left Back
Rail Leg (1PC)
F. Right Back Rail
Leg (1PC) i. Allen Wrench (1pc) f. Barrel nuts (4pcs)
Attach crib end top rail(A) to left back leg(E) using
1-3/8’’ allen head bolts (c) and left crib end bottom rails (H) to left fback leg (E)) using 2-3/8’’ allen head bolts (b) &barrel nuts(f).; attach crib end top rail(A) to right back leg(F)
using 1-3/8’’ allen head bolts (c) and b right crib end bottom rail(I) to right back leg(F) using 2-3/8’’ allen head bolts (b) &barrel nuts(f).
c b
E f
I au
1
F
E
A et et c et
H
A f
Left
b c
F f b
I
A f
Right
8
SECTION 1: Crib Assembly
STEP3
Parts and tools required to complete step.
a. 3” Allen head Bolt (8pcs)
G.Back Rail (1PC) f. Barrel nuts (16pcs)
Left Right
From Step 2 i. Allen Wrench (1pc) j.3-3/8” Allen head Bolt (2pcs)
Attach left crib end and right crib end to back rail(G)
using 3-3/8’’ allen head bolts (a)(j)& barrel nuts(f),allen wrench(i).
(a)(j) j a
G j f x4
Model shown is example only.
Styles may vary .
a
99
SECTION 1: Crib Assembly
STEP 4
Parts and tools required to complete step.
d.3/4” Allen head Bolt (4pcs) e.Nuts (4pcs)
J. Wooden Mattress Base (1PC) g. Metal connection (4pcs)
From Step 3 d
J g
Attach metal connection(g) to the wooden mattress base(J) by using bolts(h) and nuts(e) with wrench.
Position the wooden mattress base
(J) to a selected position on legs.
Insert the bolts(d) into thread inserts on legs,tighten securely with
Allen wrench(i) after the front rail is assembled.Be sure the flat side of wooden mattress base(J) is upward. h
J e
10
Not Supplide
The Warnings printed on the pouch attached to the mattress support must
face up. This crib has adjustment positions, use the highest only for new borns, move the mattress down as the child grows.
WARNING:
Fall Hazard: When child is able to pull to a standing position,set mattress to lowest position and remove bumper pads ,large toys and other objects that could serve as steps for climbing out.
SECTION 1: Crib Assembly
STEP 5
Parts and tools required to complete step.
a. 3” Allen head Bolt (6pcs) f. Barrel nuts (16pcs)
From Step 4 B. Front Rail (1PC)
Attach The front rail (B) and left ceib ends and right crib end using 3’’allen head bolts (a), barrel nuts(f) and allen wrench (i) .
i. Allen wrench a f a a f
B f a
Model shown is example only.
Styles may vary .
f
11
SECTION 1: Crib Assembly
STEP6
Parts and tools required to complete step.
From Step 5 K. Mattress (1PC)
K
Put the mattress(K) into the bed.
Model shown is example only.
Styles may vary .
12
SECTION 2: Day Bed Conversion
STEP 1
Parts and tools required to complete step.
Finished Crib i. Allen wrench
Remove the Front Rail installed in step 5 of section 1 Crib Assembly.
a f
B f a f a a f
13
SECTION 2: Day Bed Conversion
STEP 2
The mattress support must be in the lowest positions.
Store all hardware safely.
14
SECTION 3: Twin Bed Conversion
(Hollywood bed frame sold separately)
Parts and tools required to complete step.
Not Supplied Not Supplied
Not Supplied
Split leg (2PCS)
Not Supplied
i:Allen wrench
Conversion kit is sold separately
You have the option to convert crib to a twin bed
1.Remove the right&left crib end, and leave the legs on the front&back rail, as the parts list shown.
2.Use the front rail as the footboard of twin bed.
headboard of twin bed.
back rail to the kits ( legs, long
rails,and hardware ) which are not included and sold separately.
15
SECTION 4: Youth Bed Conversion
(Hollywood bed frame sold separately)
Parts and tools required to complete step.
Bar (3PCS)
Not Supplied Not Supplied
Left Right
Split leg (2PCS)
Not Supplied i:Allen wrench
Not Supplied
Conversion kit is sold separately
You have the option to convert crib to a youth bed.
1.Remove the front&back rail, and leave the legs on the left&right crib end, as the parts list shown.
2.Use the left crib end as the footboard of youth bed.
headboard of youth bed.
rails,and hardware ) which are not included and sold separately.
Le Kit de conversion est fourni séparément
Vous avez la possibilité de convertir la crèche à un lit de taille complète
1.Utilisez le rail de la tête arrière du grand lit.
2.Connectez la plate-forme de pied gauche et la plateforme de pied droit sur les rails qui ne sont pas inclus et vendu séparément.
3.Connectez les pièces assemblées et tête de lit de lit de taille pour les kits (jambes, longuesrails et le matériel) qui ne sont pas inclus et vendus
séparément.
Model shown is example only.
Styles may vary .
16
Modèle présenté à titre indicatif.
Les styles peuvent varier.
To register your product for important safety alerts and updates to your product please visit www.dreamonme.com
Please do not return this item to the store before contacting us about missing parts or with any questions.
To report a problem, please log on to www.dreamonme.com and contact us by phone at 732-366-1788
In the event that you need to contact our customer service department please have the Style Number and MFG available.
Use the space below to make note of those numbers. They can be found on the label on the Crib End bottom rail.
STYLE No: 633
COLOR FTY
Lot No:
Pack Date:
Date of Purchase: (you should also keep your receipt)
17
LIMITED WARRANTY
� Dream on Me warrants its product to be free from defects in material and
workmanship and agrees to remedy any such defect.
� This warranty covers 30 days from the date of original purchase.
� This warranty is valid only upon presentation of proof of purchase.
This is solely limited to the repair or replacement of defective furniture
components and no assembly labor is included.
� This warranty does not apply to any product which has been improperly
assembled, subjected to misuse or abuse or which has been altered or
repaired in any way.
� This warranty gives you specific legal rights and you may also have other
rights which vary from State to State.
WARNING: Should this product become damaged, and/or components are broken or missing, DO NOT USE
18
