GT15 Printer unit User`s Manual

Add to My manuals
1 Pages

advertisement

GT15 Printer unit User`s Manual | Manualzz

GT15 Printer unit

User's Manual

GT15-PRN

Thank you for purchasing the GOT1000 Series.

Prior to use, please read both this manual and detailed manual thoroughly to fully understand the product.

MODEL

MODEL

CODE

GT15-PRN-U

1D7M47

IB(NA)-0800334-I(1106)MEE

z SAFETY PRECAUTIONSz

(Always read these precautions before using this equipment.)

Before using this product, please read this manual and the relevant manuals introduced in this manual carefully and pay full attention to safety to handle the product correctly.

The precautions given in this manual are concerned with this product.

In this manual, the safety precautions are ranked as "DANGER" and

"CAUTION".

DANGER

Indicates that incorrect handling may cause hazardous conditions, resulting in death or severe injury.

CAUTION

Indicates that incorrect handling may cause hazardous conditions, resulting in medium or slight personal injury or physical damage.

Note that the CAUTION level may lead to a serious accident according to the circumstances.

Always follow the precautions of both levels because they are important to personal safety.

Please save this manual to make it accessible when required and always forward it to the end user.

[DESIGN PRECAUTIONS]

DANGER

z Do not bunch the control wires or communication cables with

the main circuit or power wires, or lay them close to each other.

As a guide, separate the lines by a distance of at least 100mm

(3.94 inches) otherwise malfunctions may occur due to noise.

[INSTALLATION PRECAUTIONS]

DANGER

z Be sure to shut off all phases of the external power supply used by the system before mounting or removing this unit to/from the

GOT.

Not doing so can cause a unit failure or malfunction.

z Before connecting the Bus connection cable to this unit, always shut off GOT power and PLC CPU power externally in all phases.Not doing so can cause a malfunction.

CAUTION

z Use this unit in the environment that satisfies the general specifications described in the User's Manual for the GOT used.

Not doing so can cause an electric shock, fire, malfunction or product damage or deterioration.

z When installing this unit to the GOT, fit it to the connection interface of the GOT and tighten the mounting screws in the specified torque range.

Undertightening can cause a drop, failure or malfunction.

Overtightening can cause a drop, failure or malfunction due to screw or unit damage.

[WIRING PRECAUTIONS]

DANGER

z Be sure to shut off all phases of the external power supply used by the system before wiring.

Failure to do so may result in an electric shock, product damage or malfunctions.

CAUTION

z Exercise care to avoid foreign matter such as chips and wire offcuts entering the unit.

Not doing so can cause a fire, failure or malfunction.

[STARTUP AND MAINTENANCE PRECAUTIONS]

DANGER

z Before starting cleaning, always shut off GOT power externally in all phases. Not doing so can cause a unit failure or malfunction.

Undertightening can cause the GOT to drop, short circuit or malfunction.

Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit.

z Do not disassemble or modify any unit.

This will cause failure, malfunction, injuries, or fire.

z Do not touch the conductive areas and electronic parts of this unit directly.

Doing so can cause a unit malfunction or failure.

CAUTION

z Always secure the cables connected to the unit, e.g. run them in conduits or clamp them.

Not doing so can cause unit or cable damage due to dangling, moved or accidentally pulled cables or can cause a malfunction due to a cable contact fault.

z Do not hold the cable part when unplugging any cable connected to the unit. Doing so can cause unit or cable damage or a malfunction due to a cable contact fault.

z Do not drop the module or subject it to string shock.

A module damage may result.

z Always make sure to touch the grounded metal to discharge the electricity charged in the body, etc., before touching the unit.

Failure to do so may cause a failure or malfunctions of the unit.

[DISPOSAL PRECAUTIONS]

CAUTION

z Dispose of this product as industrial waste.

[TRANSPORTATION PRECAUTIONS]

CAUTION

z Make sure to transport the GOT main unit and/or relevant unit(s) in the manner they will not be exposed to the impact exceeding the impact resistance described in the general specifications of the User’s Manual for the GOT used, as they are precision devices.

Failure to do so may cause the unit to fail.

Check if the unit operates correctly after transportation.

Manuals

The following shows manuals relevant to this product.

Detailed Manual

Manual name

GT16 User's Manual (Hardware)

(Sold separately)

GT15 User's Manual

(Sold separately)

GOT1000 Series Connection Manual

(Microcomputer, MODBUS Products,

Peripherals) for GT Works3

(Sold separately)

Manual number

(Model code)

SH-080928ENG

(1D7MD3)

SH-080528ENG

(1D7M23)

SH-080871ENG

(1D7MC5)

Relevant Manuals

For relevant manuals, refer to the PDF manuals stored in the CD-

ROM for the drawing software used.

© 2005 MITSUBISHI ELECTRIC CORPORATION

Compliance with the EMC and Low Voltage

Directives

To configure a system meeting the requirements of the EMC and Low

Voltage Directives when incorporating the Mitsubishi GOT (EMC and

Low Voltage Directives compliant) into other machinery or equipment, refer to "EMC AND LOW VOLTAGE DIRECTIVES" of the

General Description included with the GOT used.

The CE mark, indicating compliance with the EMC and Low Voltage

Directives, is printed on the rating plate of the GOT.

Compliance with the Radio Waves Act (South

Korea)

This product complies with the Radio Waves Act (South Korea).

Note the following when using the product in South Korea.

이 기기는 업무용 (A 급 ) 전자파적합기기로서 판매자 또는

사용자는 이 점을 주의하시기 바라며 , 가정외의 지역에서

사용하는 것을 목적으 로 합니다 .

(The product is for business use (Class A) and meets the electromagnetic compatibility requirements.

The seller and the user must note the above point, and use the product in a place except for home.)

Packing List

The following items are included.

Model

GT15-PRN

Product

Printer unit

Mounting screw set (2 pieces of screw,

2 pieces of sticker)

Cable clamp set (Connector holder with screw, cable clamp)

GT09-

C30USB-5P

Dedicated printer connection cable (3m)

Quantity

1

1

1

1

1. OVERVIEW

This User's Manual describes the GT15 printer unit.(hereinafter referred to as the printer unit)

With the printer unit installed, the GOT can be connected to a printer.

Refer to the User’s Manual for the GOT used for the applicable GOT.

Use PictBridge compatible printers.

Printers incompatible with PictBridge cannot be used with the GOT.

2. SPECIFICATIONS

The performance specifications of the printer unit are indicated below.

The general specifications of the printer unit are the same as those of the GOT.

Refer to the User’s Manual for the GOT used for the general specifications of the GOT.

Specification Item

Internal current consumption (5VDC)

0.09A

Weight

0.08kg (0.18lb) (Including connector holder and cable clamp)

3. PART NAMES AND EXTERNAL

DIMENSIONS

63(2.48) 3

(0.12)

GOT main unit

(3) Depending on the use environment such as when fastening cable is difficult, attach a cable clamp to the printer unit.

Be sure to attach the cable clamp to section A (see the following figure) with its band positioned outside and press it until it clicks.

For the band inserting direction, refer to the arrow.

(In the case a cable clamp is attached)

(4) Insert the dedicated printer connection cable in the looped cable clamp band and pull the band to fasten the cable.

(3) (4)

1)

5)

3)

2.4

(0.09)

4)

2)

X

13.5

(0.53)

Unit: mm (inch)

* The external dimensions of printer unit with a cable clamp and connector holder attached is shown above.

Dimensions of X when the printer unit is mounted to the GOT

No.

15"

12.1"

10.4"

8.4"

5.7"

Name

1) Mounting screw

2) Connector holder

3) Cable clamp

4) Connector

5) Rating plate

GOT GT16 GT15

19.5 (0.77) 21 (0.83)

18 (0.71)

21 (0.83)

18 (0.71)

21 (0.83)

23 (0.92)

23 (0.91)

23 (0.92)

23 (0.91)

Unit : mm(inch)

Description

Mounting screws fixed with the front communication unit or GOT

Holder for preventing a dedicated printer connection cable disconnection

For cable treatment

USB connector for connecting a dedicated printer connection cable

-

4. INSTALLATION PROCEDURE

4.1 Cable Connection

(1) Connect a dedicated printer connection cable to the printer unit.

(2) Attach the accessory connector holder to the dedicated printer connection cable and tighten the screw of connector holder with tightening torque of 0.36 to 0.48N•m.

(1) (2)

Dedicated printer connection cable

Connector holder

A

Cable clamp

4.2 Unit Installation

The installation procedure for the printer unit is explained using the

GT1575.

(1) Power off the GOT.

(2) Remove one extension unit cover of the GOT.

(3) Fit the printer unit in the GOT case.

In the case a cable clamp is attached

(4) Fasten the printer unit by tightening its mounting screws (2 places) with tightening torque 0.36 to 0.48 N•m.

In the case a cable clamp is attached

(5) When mounting any communication unit on the outer stage, refer to the User's Manual for the GOT used.

When not mounting any communication unit on the outer layer, stick accessory stickers on the top of mounting screws (2 places) to cover the top of them in order to avoid receiving electrostatic.

Keep the connector cover and sticker (see thefollowing figure) fixed.

Accessory stickers

Connector cover

Sticker

Point

(1) Cable to be used

When connecting the printer to the GOT, use the supplied dedicated printer connection cable.

(2) Precautions for connecting the dedicated printer connection cable (USB cable)

• Wait 5s or more between the connection and disconnection of the dedicated printer connection cable.

If connecting or disconnecting the dedicated printer connection cable shortly after disconnecting or connecting the cable, the

GOT may not operate normally.

• Do not connect or disconnect the dedicated printer connection cable during printing.

Doing so can cause the GOT operate incorrectly.

• Connected printer may not be recognized in rare cases.

When printer is not recognized, disconnect the dedicated printer connection cable once and connect it again.

• When the printer has been connected to a personal computer and used before it is connected to GOT, power on the printer again and connect it to GOT.

• Any printer cannot be connected to GOT via USB hub.

• Do not connect any devices to the printer while GOT is connected to it.

• Do not connect any devices other than printer to the printer unit.

(3) Cable connection/disconnection

Wait 3s or more between the connecting and disconnecting operations of the dedicated printer connection cable.

If not waiting 3s or more, the GOT may not operate normally.

(4) Printer unit removal

If you remove the Printer unit, detach it from specified direction

(shown PULL) so as not to break a connector.

(5) Cable clamp

(a) Pulling out the cable clamp band

The cable clamp band can be pulled out after cable treatment.

Pull out the band with pressing the tab of the cable clamp outward using a screwdriver etc.

(b) Removing from the printer unit

The dedicated printer connection cable can be removed from the unit with the cable clamp attached.

Remove the cable clamp by pressing it in both directions

(arrow A).

A

(6) Screw of the connector holder

Do not remove the screw attached to the connector holder.

In the case the screw is removed, do not use any other screws.

Doing so may damage the unit.

Warranty

Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi; machine damage or lost profits caused by faults in the Mitsubishi products; damage, secondary damage, accident compensation caused by special factors unpredictable by Mitsubishi; damages to products other than

Mitsubishi products; and to other duties.

For safe use

• This product has been manufactured as a general-purpose part for general industries, and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life.

• Before using the product for special purposes such as nuclear power, electric power, aerospace, medicine or passenger movement vehicles, consult with Mitsubishi.

• This product has been manufactured under strict quality control.

However, when installing the product where major accidents or losses could occur if the product fails, install appropriate backup or failsafe functions in the system.

Country/Region Sales office/Tel

U.S.A

Brazil

Germany

U.K

Italy

Spain

France

South Africa

Hong Kong

China

Mitsubishi Electric Automation Inc.

500 Corporate Woods Parkway Vernon Hills, IL 60061, U.S.A.

Tel : +1-847-478-2100

MELCO-TEC Rep. Com.e Assessoria Tecnica Ltda.

Rua Correia Dias, 184, Edificio Paraiso Trade Center-8 andar

Paraiso, Sao Paulo, SP Brazil

Tel : +55-11-5908-8331

Mitsubishi Electric Europe B.V. German Branch

Gothaer Strasse 8 D-40880 Ratingen, GERMANY

Tel : +49-2102-486-0

Mitsubishi Electric Europe B.V. UK Branch

Travellers Lane, Hatfield, Hertfordshire., AL10 8XB, U.K.

Tel : +44-1707-276100

Mitsubishi Electric Europe B.V. Italian Branch

Centro Dir. Colleoni, Pal. Perseo-Ingr.2

Via Paracelso 12, I-20041 Agrate Brianza., Milano, Italy

Tel : +39-039-60531

Mitsubishi Electric Europe B.V. Spanish Branch

Carretera de Rubi 76-80,

E-08190 Sant Cugat del Valles, Barcelona, Spain

Tel : +34-93-565-3131

Mitsubishi Electric Europe B.V. French Branch

25, Boulevard des Bouvets, F-92741 Nanterre Cedex, France

Tel : +33-1-5568-5568

Circuit Breaker Industries Ltd.

Private Bag 2016, ZA-1600 Isando, South Africa

Tel : +27-11-928-2000

Mitsubishi Electric Automation (Hong Kong) Ltd.

10th Floor, Manulife Tower, 169 Electric

Road, North Point, Hong Kong

Tel : +852-2887-8870

Mitsubishi Electric Automation (China) Ltd.

Taiwan

4/F Zhi Fu Plazz, No.80 Xin Chang Road,

Shanghai 200003, China

Tel : +86-21-6120-0808

Setsuyo Enterprise Co., Ltd.

6F No.105 Wu-Kung 3rd.Rd, Wu-Ku Hsiang,

Taipei

Korea

Tel : +886-2-2299-2499

Mitsubishi Electric Automation Korea Co., Ltd.

1480-6, Gayang-dong, Gangseo-ku Seoul

Korea

Singapore

Tel : +82-2-3660-9552

Mitsubishi Electric Asia Pte, Ltd.

307 #05-01/02,

Mitsubishi Electric Building, Singapore 159943

Thailand

Tel : +65-6470-2460

Mitsubishi Electric Automation (Thailand) Co., Ltd.

Bang-Chan Industrial Estate No.111 Moo 4, Serithai Rd,

T.Kannayao,

Indonesia

India

Tel : +66-2-517-1326

P.T. Autoteknindo Sumber Makmur

Muara Karang Selatan, Block A/Utara

No.1 Kav. No.11 Kawasan Industri Pergudangan

Jakarta - Utara 14440, P.O.Box 5045 Jakarta, 11050 Indonesia

Tel : +62-21-6630833

Messung Systems Pvt, Ltd.

Electronic Sadan NO:III Unit No15, M.I.D.C Bhosari,

Pune-411026,

Tel : +91-20-2712-3130

Australia Mitsubishi Electric Australia Pty. Ltd.

348 Victoria Road, Rydalmere, N.S.W 2116, Australia

Tel : +61-2-9684-7777

HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN

NAGOYA WORKS : 1-14, YADA-MINAMI 5-CHOME, HIGASHI-KU, NAGOYA, JAPAN

When exported from Japan, this manual does not require application to the Ministry of Economy, Trade and Industry for service transaction permission.

Specifications subject to change without notice.

Printed in Japan, June 2011.

advertisement

Related manuals

Download PDF

advertisement