Clarke DEVIL 2800PTC 2.8KW 230V PTC Electric Fan Heater Instruction manual

Add to My manuals
12 Pages

advertisement

Clarke DEVIL 2800PTC 2.8KW 230V PTC Electric Fan Heater Instruction manual | Manualzz

Only suitable for well insulated areas and not designed to be the primary heat source

2.8KW 230V PTC ELECTRIC FAN HEATER

MODEL NO: DEVIL 2800PTC

PART NO: 6925600

OPERATION & MAINTENANCE

INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC0621 rev 1

INTRODUCTION

Thank you for purchasing this CLARKE Electric Fan Heater.

Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended.

Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission.

This guarantee does not effect your statutory rights.

SPECIFICATIONS

Operating Voltage and Frequency:

Operating Temperature: (Min/Max)

Max Heat Output:

Air Output:

Safety Device:

Duty Cycle Classification:

Electrical Insulation Class

Ingress protection

Product: Depth x Width x Height

Product Weight

230 V / 50Hz / 1 Phase

-15 to +25°C

2.8 kW - 9554 BTU/hr.

280m 3 /h

Thermal cut-out

S1 Continuous duty

I

IP20

265 x 210 x 290 mm

2.8 kg

2

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

THE FOLLOWING TABLE ADDRESSES THE

INFORMATION REQUIREMENTS OF REG.2015/1188

Item

Heat output

Measured seasonal space heating energy efficiency

Nominal heat output

Symbol

Minimum heat output (indicative)

Maximum continuous heat output

P nom

P min

P max

Auxiliary electricity consumption

At nominal heat output

At minimum heat output

In standby mode el max el min el

SB

Type of heat input for electric storage local heaters only

Manual heat charge control with integrated thermostat

Manual heat charge control with room and/or outdoor temperature feedback

Electronic heat charge control with room and/or outdoor temperature feedback

Value

2.8

1.4

2.8

n/a n/a n/a

Fan assisted output

Type of heat output/room temperature control (select one)

Single stage heat output, no temperature control

Two or more manual stages, no temperature control

With mechanical thermostat temp control

With electronic temperature control

Electronic temperature control with day timer

Electronic temperature control with week timer

Other control options (multiple selections possible)

Room temperature control with presence detection

Room temperature control with open window detection

Room temperature control with distance control option

Room temperature control with adaptive start control

Room temperature control with working time limitation

Room temperature control with black bulb sensor

Unit

No

No

No

No

No

No

Yes

No

No

No

No

No

No

No

No

No

36% kW kW kW kW kW kW

3

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

SAFETY ADVICE

Make sure that you read, understand and comply with the following.

The following symbols appear on the unit.

Hot surface,- do not touch

Do not cover

Read the manual

ELECTRICAL SAFETY

• Regularly inspect the power cable / plugs to be used with this heater and DO NOT use the heater if the power cable is damaged.

• Minimise the risk of electric shock by installing a RCCB (Residual Current

Circuit Breaker).

• Make sure that the voltage on the rating plate is the same as the voltage of the power supply. If in doubt, consult a qualified electrician.

• DO NOT abuse any electrical cable used with this heater. NEVER use the cable for pulling or unplugging the heater.

• Keep the cable away from sources of heat, oil, sharp edges or moving parts. Damaged or tangled cables increase the risk of electric shock.

OPERATION

• The heater must only be used by persons who have read these instructions and have been trained in its use.

• DO NOT obstruct the air inlet and outlet sections of the heater.

• DO NOT cover the heater.

• DO NOT touch the heater casing or grille when first switched off, as these will be very hot and will take time to cool.

• DO NOT get the heater wet or use in areas of high condensation.

• DO NOT allow the power cable to touch hot surfaces.

• DO NOT connect other appliances to the same mains socket as the heater.

• ONLY use the heater on a level surface.

• DO NOT use this heater with a programmable timer used to switch it on automatically.

4

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

POSITIONING

WARNING: DO NOT USE THE HEATER NEAR FLAMMABLE MATERIAL,

LIQUIDS, SOLIDS, GASES OR COMPRESSED GAS CYLINDERS ETC.

• This heater is designed for indoor use only.

• DO NOT place the heater close to a bath, wash basin, shower, swimming pool or any other water-filled area or wet surface. DO NOT place the heater up against any surface such as a wall, door or furniture etc.

• DO NOT place the heater immediately below any electrical outlet.

• NEVER place the heater near combustible materials such as curtains, furniture etc. Allow at least 2 metre clearance.

• DO NOT place the heater on a raised surface or anywhere where it could topple over

• ALWAYS ensure that the grille cannot be blocked by curtains or other fabrics.

• DO NOT operate in explosive atmospheres such as in the presence of flammable liquids, gases or dust such as in a paint spray booth or any explosive environment. Electric motors create sparks which may ignite dust or fumes.

• DO NOT LEAVE THE HEATER UN-ATTENDED, FOR EXAMPLE, LEFT ON AT

NIGHT.

COMMON SENSE

• DO NOT operate when you are tired or under the influence of alcohol, drugs or intoxicating medication.

• DO NOT stand on the heater.

• DO NOT use the heater with wet hands or when there is water on the power cable.

• Turn the heater off when not in use and keep it in a safe, dry, childproof location.

• The heater is designed to heat enclosed areas, such as workshops and other industrial areas. DO NOT use the heater for any other function. It is not suitable for drying clothes or laundry.

• Young children must be kept away unless continuously supervised.

• DO NOT touch the heater casing or grille during use.

5

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

ELECTRICAL CONNECTIONS

WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY

BEFORE CONNECTING THE HEATER TO THE MAINS SUPPLY.

Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. Connecting it to any other power source may cause damage.

If it is necessary to change the fuse in the plug, the fuse cover must be refitted.

If the fuse cover becomes lost or damaged, the plug must not be used until a suitable replacement is obtained.

If the plug has to be changed due to damage, a replacement should be fitted, following the wiring instructions shown below. The old plug must be disposed of as insertion into a mains socket could cause an electrical hazard.

WARNING: THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE

COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

BLUE = NEUTRAL BROWN = LIVE YELLOW/GREEN = EARTH

If the colors of the wires in the power cable of this product do not correspond with the markings on the terminals of your plug, proceed as follows.

• The Blue wire must be connected to the terminal which is marked N or coloured

Black .

• The Brown wire must be connected to the terminal which is marked L or coloured

Red .

• The Yellow/Green wire must be connected to the terminal which is marked E or coloured Green.

We strongly recommend that this machine is connected to the mains supply via a Residual Current Device (RCD)

If in any doubt, consult a qualified electrician. DO NOT attempt any repairs yourself.

6

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

OPERATION

WARNING: DO NOT USE THIS HEATER IN SMALL ROOMS WHEN THEY ARE

OCCUPIED BY PERSONS NOT CAPABLE OF LEAVING THE ROOM ON THEIR

OWN, UNLESS CONSTANT SUPERVISION IS PROVIDED.

CAUTION: SOME PARTS OF THIS PRODUCT CAN BECOME VERY HOT AND

CAN CAUSE BURNS. PARTICULAR ATTENTION HAS TO BE GIVEN WHERE

CHILDREN AND VULNERABLE PEOPLE ARE PRESENT.

1. Put the heater in a level position on a flat surface and at a safe distance from flammable materials. Keep a minimum of 2m clearance all round.

2. Connect the heater to a suitable power supply.

3. Set the thermostat control to the maximum setting (fully clockwise).

4. Set the mode selector to one of the 3 settings:

Off

Fan Only

Heat Setting 1

Heat Setting 2

• The heater will take up to three minutes to reach optimum temperature.

5. Once the room reaches the required temperature, turn the thermostat control slowly counter-clockwise until the thermostat clicks, leave the control in this position.

• The room temperature will be maintained at this setting. The heater will continue to operate until the power switch is turned to the OFF position.

7

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

6. For fan only operation, turn the power switch to the fan only setting and set the thermostat to its minimum setting.

7. Adjust the angle by loosening both adjusting knobs and setting the required angle.

8. Retighten the adjusting knobs.

9. When not in use, disconnect the heater from the mains supply.

Store it in a safe, dry, childproof location.

MAINTENANCE

.

WARNING: SERVICING OR INTERNAL MAINTENANCE MUST ONLY BE

CARRIED OUT BY THE CLARKE SERVICE DEPARTMENT.

WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY AND ALLOW

THE HEATER IT TO COOL DOWN BEFORE PERFORMING ANY

MAINTENANCE TASKS.

• Check that the heater is in good working order. Take immediate action to repair or replace damaged parts.

• DO NOT allow the heating elements to become covered with dust which could become a fire hazard. If used in a dusty workplace it should be cleaned after every use with a dust extractor.

• ONLY recommended parts should be used. Unapproved parts may be dangerous and will invalidate the warranty.

• DO NOT attempt to repair a damaged heater, contact the CLARKE service department.

• Clean the heater with a soft damp cloth once cold. DO NOT use solvents or abrasives

• No other maintenance is required, should you discover any problem with the heater, return it to the CLARKE service department for repair.

8

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

SERVICE & REPAIRS

Have your heater repaired by a qualified person using identical replacement parts. This will ensure that the safety of the heater is maintained.

TROUBLE SHOOTING

Problem

Heater does not operate, although plugged in with the switch and thermostat switched on.

Possible Cause

Plug is loose/bad connection.

Fuse blown or circuit breaker trips.

Remedy

Pull the plug out & check all connections (cable/plug and socket).

Replace if necessary and investigate cause. If fuse blows repeatedly, consult your CLARKE dealer.

Insert the plug in a suitable socket.

Heating element glowing hot.

No power at socket outlet

Input voltage too high.

Use a power supply in accordance with the rating on the label.

Air inlet grille is blocked.

Ensure the heater is kept away from any objects which could cover the air inlet or be drawn into it.

Turn switch to a heating level. The unit has failed to heat up so only the air fan has operated.

Control switch not set at a

“HEATING” level.

Thermal cut out device is active/

Thermostat has tripped

Turn the thermostat and listen. If there is no CLICK and the thermostat is not damaged, the heater will automatically switch ON when it has cooled down.

Abnormal noise.

Heater is not level. Stand heater on a level surface.

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the obligation to deal with the WEEE in accordance with the WEEE regulations in relation to the treatment, recycling & recovery and environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general household waste. It must be disposed of according to the laws governing

Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal facility.

9

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

COMPONENT PARTS

6

7

4

5

1

2

3

8

9

10

11

Front Grille

Air Outlet Shutter Fixed Ring

PTC Heating Element

Air Flue

Fan Plate

Fan

Motor

Motor Support

Rotary Switch

Adjustable Thermostat

Mode Selector Knob

15

16

17

18

12

13

14

19

20

21

Thermostat Knob

Control Box Cover

Cable Clamp

Power Cable/Plug

Back Grille

M6 x 16mm Screw

Steel Pipe Frame

Outer Casing

Self-Resetting Thermostat

Temperature Probe

10

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

DECLARATIONS OF CONFORMITY

11

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

advertisement

Key Features

  • Powerful 2.8kW heat output for efficient heating
  • PTC technology for rapid heat-up and energy efficiency
  • 280m3/h air output for quick heat distribution
  • Adjustable thermostat for precise temperature control
  • Built-in thermal cut-out for overheat protection
  • Quiet operation for use in living areas and offices
  • Rugged design and sturdy base for stability

Related manuals

Frequently Answers and Questions

What is the maximum heat output of the Clarke DEVIL 2800PTC?
The maximum heat output is 2.8kW.
Is the Clarke DEVIL 2800PTC suitable for outdoor use?
No, it is designed for indoor use only.
Does the Clarke DEVIL 2800PTC have a remote control?
No, it does not have a remote control.
What is the IP rating of the Clarke DEVIL 2800PTC?
The IP rating is IP20, indicating protection against solid objects larger than 12mm but no protection against water.