VER:1.3 │ │ 28.04.2017

ABB-Welcome

Pos: 2 /DinA4 - Anl eitun gen Online /Inh alt/KNX/Doo rEntry /832 20-AP- xxx/Tit elblat t - 832 20-AP-xxx - ABB @ 1 9\m od_ 132 3249 806 476 _15. docx @ 11 108 4 @ @ 1

M2302

Gateway

=== E nde der Liste für Tex tma rke C over == =

ABB-Welcome

5

6

Pos: 4 /Busc h-Ja ege r (N eust rukt ur)/ Mo dul-St ruktu r/Onli ne-D oku ment ation /Inh altsve rzeich nis ( --> Fü r alle Doku men te <-- )/In haltsve rzeic hnis @ 19\ mod _13 206 490 4438 6_1 5.d ocx @ 109 653 @ @ 1

1

2

3

4

Safety ....................................................................................................... 3

Intended use ............................................................................................. 3

Environment .............................................................................................. 3

3.1

ABB devices ............................................................................. 3

Operation .................................................................................................. 5

4.1

Control elements ....................................................................... 5

4.2

Operating modes ...................................................................... 6

4.2.1

4.2.2

4.2.3

Building gateway ....................................................................... 6

Floor gateway ........................................................................... 8

Apartment gateway ................................................................. 12

4.2.4

4.2.5

Additional power supply mode ................................................. 15

Line amplifier .......................................................................... 18

Technical data......................................................................................... 20

Mounting/Installation ............................................................................... 21

6.1

6.2

6.3

Requirements for the electrician............................................... 21

General installation instructions ............................................... 22

Mounting ................................................................................. 22

=== E nde der Liste für Tex tma rke TOC == =

| — 2 —

ABB-Welcome

Pos: 6 /Busc h-Ja ege r (N eust rukt ur)/ Mo dul-St ruktu r/Onli ne-D oku ment ation /Übe rschri ften (- -> Für alle D okum ent e < --)/ 1. Eb ene/S - T /Sicher heit @ 18\ mod _13 026 127 917 90_ 15.d ocx @ 103 357 @ 1 @ 1

1 Safety

Pos: 7 /Busc h-Ja ege r (N eust rukt ur)/ Mo dul-St ruktu r/Onli ne-D oku ment ation /Sicher heit (-- > Für alle Dok um ente <- -)/Wa rn hinweise /Sicher heit - 23 0 V @ 18\m od_ 130 260 681 675 0_15 .docx @ 1 033 08 @ @ 1

Warning

Electric voltage!

Dangerous currents flow through the body when coming into direct or indirect contact with live components.

This can result in electric shock, burns or even death.

■

Disconnect the mains power supply prior to installation and/or disassembly!

■

Permit work on the 110-240 V supply system to be perf ormed only by specialist staff!

Pos: 8 /Busc h-Ja ege r (N eust rukt ur)/ Mo dul-St ruktu r/Onli ne-D oku ment ation /Übe rschri ften (- -> Für alle D okum ent e < --)/ 1. Eb ene/A - F /Bestim mun gsge mä ßer Geb rau ch @ 18\ mod _13 027 6332 131 6_1 5.do cx @ 1034 83 @ 1 @ 1

2 Intended use

Pos: 9 /DinA4 - Anl eitun gen Online /Inh alt/KNX/Doo rEntry /832 20-AP- xxx/Besti mmu ngsg em aesse r Ge bra uch - 83 220 -AP-xxx- 500 @ 2 0\mo d_1 324 561 168 699 _15. docx @ 11 272 8 @ @ 1

This device is an integral part of the ABB-W elcome door communication system and operates exclusively with components from this system. The device must only be installed on mounting rails according to DIN EN 500022.

Pos: 10 /B usch-J aeg er (Neus truk tur )/M odul -Strukt ur/O nline -Doku me ntatio n/Übe rsch rifte n ( --> Fü r alle Doku men te < -- )/1. E bene /U - Z/U mwelt @ 18\ mod _13 026 141 5896 7_1 5.d ocx @ 103 383 @ 1 @ 1

3 Environment

Pos: 11 /B usch-J aeg er (Neus truk tur )/M odul -Strukt ur/O nline -Doku me ntatio n/Umw elt ( --> F ür all e Doku me nte <-- )/Hinweis e/Hinw eis - U mwelt - Hinweis Elektr oge räte @ 1 8\mo d_1 302 763 973 434 _15. docx @ 10 350 0 @ @ 1

Consider the protection of the environment!

Used electric and electronic devices must not be disposed of with domestic waste.

– The device contains valuable raw materials that can be recycled.

Therefore, dispose of the device at the appropriate recycling facility.

Pos: 12 /Di nA4 - A nleitu ngen Onlin e/Ueb ersc hrift en/2 ./ABB Gera ete @ 19 \mo d_1 323 162 843 832_ 15. docx @ 11 087 5 @ 2 @ 1

3.1

ABB devices

Pos: 13 /B usch-J aeg er (Neus truk tur )/M odul -Strukt ur/O nline -Doku me ntatio n/Umw elt ( --> F ür all e Doku me nte <-- )/Hinweis e/Hinw eis - U mwelt - ABB Elektro ger äte @ 19\ mo d_1 3231 627 458 39_ 15.d ocx @ 110 867 @ @ 1

| — 3 —

ABB-Welcome

All packaging materials and devices from ABB bear the markings and test seals f or proper disposal. Always dispose of the packaging material and electric devices and their components via an authorized recycling facilities or disposal companies.

ABB products meet the legal requirements, in particular the laws governing electronic and electrical devices and the REACH ordinance.

(EU-Directive 2002/96/EG W EEE and 2002/95/EG RoHS)

(EU-REACH ordinance and law for the implementation of the ordinance (EG)

No.1907/2006)

| — 4 —

ABB-Welcome

Pos: 18 /Di nA4 - A nleitu ngen Onlin e/Ueb ersc hrift en/1 ./Bedie nun g @ 18\m od_ 130 261 392 416 5_15 .docx @ 1 033 65 @ 1 @ 1

4 Operation

Pos: 19 /Di nA4 - A nleitu ngen Onlin e/Ueb ersc hrift en/2 ./Nor male r Bet rieb @ 18 \mo d_1 302 768 8209 65_ 15. docx @ 10 3540 @ 2 @ 1

4.1

Control elements

Pos: 20 /Di nA4 - A nleitu ngen Onlin e/Ueb ersc hrift en/3 ./Bedie nele men te @ 20\ mod _13 232 6022 055 9_1 5.do cx @ 1 116 47 @ 3 @ 1

Pos: 21 /Di nA4 - A nleitu ngen Onlin e/In halt/KNX/Do orEnt ry/83 220 -AP-xxx/Be dienel eme nte - 8 322 0-AP-xxx @ 18\ mo d_1 3032 128 536 05_ 15.d ocx @ 103 673 @ @ 1

Fig. 1: Overview of control buttons

2

3

No.

1

Functions

Bus in/out

Operating mode settings: See chapter “Operating modes” for details.

Terminal resistor ON/OFF.

In video installations or audio- and video-combined installations, the switch must be set as “RC on” on the last device of the line.

Rotary switches for addressing (01-99).

4

5 Connection with outdoor stations, or connection with bus in, in "line amplifier" mode.

6 Operating status indicating LED

Pos: 22 /B usch-J aeg er (Neus truk tur )/M odul -Strukt ur/O nline -Doku me ntatio n/Steu er mod ule - Onlin e-Dok ume ntati on ( -- > F ür alle Dok ume nte <- -)/ +++ ++ ++ +++ ++ S eiten umb ruch + +++ ++ ++ +++ + @ 9\m od_ 126 8898 668 093 _0. docx @ 521 49 @ @ 1

| — 5 —

ABB-Welcome

Pos: 26 /Di nA4 - A nleitu ngen Onlin e/Ueb ersc hrift en/2 ./Bedie nakti onen @ 2 0\m od_ 1323 262 294 281 _15. docx @ 11 191 1 @ 2 @ 1

4.2

Operating modes

Pos: 71 /Di nA4 - A nleitu ngen Onlin e/Ueb ersc hrift en/3 ./Abschl usswide rsta nd @ 19\ mod _13 219 5807 990 6_1 5.do cx @ 1100 83 @ 3 @ 1

Pos: 72 /Di nA4 - A nleitu ngen Onlin e/In halt/KNX/Do orEnt ry/Bedie nun g/Abschl usswide rsta nd s etzen 83 220 -AP-xxx @ 19\ mod _13 1072 339 236 9_1 5.do cx @ 1 078 41 @ @ 1

4.2.1

Building gateway

ON

1 2 3

1

Fig. 2: Building gateway

No.

1

Functions

1->OFF, 2->OFF, 3->OFF

Pos: 74 /Di nA4 - A nleitu ngen Onlin e/In halt/KNX/Do orEnt ry/Bedie nun g/M aste r/Slave Sc halte r setz en 832 20-AP-xxx @ 1 9\m od_1 310 723 320 966 _15. docx @ 10 783 3 @ @

| — 6 —

ABB-Welcome

Enable one building as an independent sub-system (outdoor station(s)/guard unit(s) can be connected). Up to 60 such systems are supported within the whole system.

The gateway address is equal to the riser number.

Fig. 3: Building gateway

Wiring diagram:

Fig. 4: Building gateway

| — 7 —

ABB-Welcome

4.2.2

Floor gateway

Fig. 5: Floor gateway

No.

1

Functions

1->OFF, 2->OFF, 3->ON

ON

1 2 3

1

| — 8 —

ABB-Welcome

Enable a multi-apartment as an independent sub-system (another outdoor station can be connected, for example in front of the door of the floor with the multi-apartment).

The gateway address is equal to the minimum address of the indoor station inside the sub-system.

Fig. 6: Floor gateway

| — 9 —

ABB-Welcome

Wiring diagram:

Fig. 7: Floor gateway

If using pushbutton outdoor station as a gate station, floor gateway is available for this kind of use case.

In following example, an outdoor station is mounted at the gate entrance with which all six apartments can be called. One outdoor station is on the left building with apartments

01 and 03 and a further outdoor station on the right building with apartments 04 and 05.

This means that only three apartments can be called from these two outdoor stations.

Using floor gateway for each building, and outdoor station 1 can manage these two buildings, while outdoor station 2 manage the left building and outdoor station 3 manage the right one.

| — 10 —

ABB-Welcome

Apartment 01 A

Apartment 02 B

Apartment 03 C

Outdoor station

Left building

Apartment 01 A

Apartment 02 B

Apartment 03 C

Apartment 04 D

Apartment 05 E

Apartment 06 F

Apartment 04 A

Apartment 05 B

Apartment 06 C

Outdoor station

Gate entrance

Outdoor station

Right building

Wiring diagram (using floor gateway for each building)

ST. X100 X10 X1

2 0 0 3

ST. X100 X10 X1

2 0 0 2

ST. X100 X10 X1

2 0 0 1

Address

2

Address

1

Address

3

ST. X100 X10 X1

3 0 0 4

ST. X100 X10 X1

3 0 0 5

ST. X100 X10 X1

3 0 0 6

Apart ment 01 A

Apart ment 02 B

Apart ment 03 C

Apart ment 01 A

Apart ment 02 B

Apart ment 03 C

Apart ment 04 D

Apart ment 05 E

Apart ment 06 F

Apart ment 04 A

Apart ment 05 B

Apart ment 06 C

M2302

X10 X1

0 1

M2302

X10 X1

0 4

| — 11 —

ABB-Welcome

4.2.3

Apartment gateway

ON

1 2 3

1

Fig. 8: Apartment gateway

No.

1

Functions

1->OFF, 2->ON, 3->OFF

| — 12 —

ABB-Welcome

Enable one apartment as an independent sub-system (The 2nd confirmed outdoor station can be connected). Up to 99 such systems can be supported within the whole system.

The gateway address is equal to the apartment number.

Fig. 9: Apartment gateway

| — 13 —

ABB-Welcome

Wiring diagram:

Fig. 10: Apartment gateway

| — 14 —

ABB-Welcome

4.2.4

Additional power supply mode

ON

1 2 3

1

Fig. 11: Additional power supply mode

No.

1

Functions

1->OFF, 2->ON, 3->ON

| — 15 —

ABB-Welcome

Enable an additional power source for systems with a system controller.

★

★

Using gateway

+ system controller as auxiliary power supply to connect to other indoor stations in the same building, when one system controller can’t cover all consmer units .

★

Fig. 12: Additional power supply mode

| — 16 —

ABB-Welcome

Wiring diagram:

Fig. 13: Additional power supply mode

| — 17 —

ABB-Welcome

4.2.5

Line amplifier

ON

1 2 3

1

Fig. 14: Line amplifier

No.

1

Functions

1->ON, 2->OFF, 3->OFF

Strengthen the video signal and extend transmission. For increased distance please refer to ABB-W elcome system manual.

Fig. 15: Line amplifier

| — 18 —

ABB-Welcome

Wiring diagram:

Fig. 16: Line amplifier

Pos: 75 /B usch-J aeg er (Neus truk tur )/M odul -Strukt ur/O nline -Doku me ntatio n/Steu er mod ule - Onlin e-Dok ume ntati on ( -- > F ür alle Dok ume nte <- -)/ +++ ++ ++ +++ ++ S eiten umb ruch + +++ ++ ++ +++ + @ 9\m od_ 126 8898 668 093 _0. docx @ 521 49 @ @ 1

| — 19 —

ABB-Welcome

Pos: 76 /Di nA4 - A nleitu ngen Onlin e/Ueb ersc hrift en/1 ./T echnisc he D aten @ 18 \mo d_1 302 615 863 001 _15. docx @ 10 341 6 @ 1 @ 1

5 Technical data

Pos: 77 /Di nA4 - A nleitu ngen Onlin e/In halt/KNX/Do orEnt ry/83 220 -AP-xxx/ Tech nische Date n - 832 20-AP-x xx @ 1 8\m od_ 130 321 285 4559 _15 .docx @ 1 037 05 @ @ 1

Designation

Operating temperature

Protection

Single-wire clamps

Fine-wire clamps

Bus voltage

Pos: 78 /B usch-J aeg er (Neus truk tur )/M odul -Strukt ur/O nline -Doku me ntatio n/Steu er mod ule - Onlin e-Dok ume ntati on ( -- > F ür alle Dok ume nte <- -)/ +++ ++ ++ +++ ++ S eiten umb ruch + +++ ++ ++ +++ + @ 9\m od_ 126 8898 668 093 _0. docx @ 521 49 @ @ 1

Value

-25 °C - +55 °C

IP 20

2 x 0.28 mm² - 2 x 0.75 mm²

2 x 0.28 mm² - 2 x 0.75 mm²

20-30 V

| — 20 —

ABB-Welcome

Pos: 79 /B usch-J aeg er (Neus truk tur )/M odul -Strukt ur/O nline -Doku me ntatio n/Übe rsch rifte n ( --> Fü r alle Doku men te < -- )/1. E bene /M - O/ Mont age / Ins tallatio n @ 18\ mod _13 0261 396 611 1_1 5.do cx @ 1 033 73 @ 1 @ 1

6 Mounting/Installation

Pos: 80 /B usch-J aeg er (Neus truk tur )/M odul -Strukt ur/O nline -Doku me ntatio n/Siche rheit (- -> Fü r alle D oku ment e < --) /War nhinweis e/Siche rheit - Nie ders pan nun gs- und 230 V-Leit ung en @ 18\ mod _13 026 178 214 91_1 5.d ocx @ 103 465 @ @ 1

Warning

Electric voltage!

Dangerous currents flow through the body when coming into direct or indirect contact with live components.

This can result in electric shock, burns or even death.

■

Disconnect the mains power supply prior to installation and/or disassembly!

■

Permit work on the 110-240 V supply system to be perf ormed only by specialist staff!

Pos: 81 /B usch-J aeg er (Neus truk tur )/M odul -Strukt ur/O nline -Doku me ntatio n/Siche rheit (- -> Fü r alle D oku ment e < --) /War nhinweis e/Siche rheit - Fachk enn tnisse @ 18 \mo d_1 302 774 384 017_ 15. docx @ 10 356 4 @ 2 @ 1

6.1

Requirements for the electrician

Warning

Electric voltage!

Install the device only if you have the necessary electrical engineering knowledge and experience.

• Incorrect installation endangers your life and that of the user of the electrical system.

• Incorrect installation can cause serious damage to property, e.g.

due to fire.

The minimum necessary expert knowledge and requirements f or the installation are as follows:

• Apply the "five safety rules" (DIN VDE 0105, EN 50110):

1.

Disconnect from power.

2.

3.

4.

Secure against being re-connected.

Ensure there is no voltage.

Connect to earth.

5.

Cover or barricade adjacent live parts.

• Use suitable personal protective clothing.

• Use only suitable tools and measuring devices.

• Check the type supply network (TN system, IT system, TT system) to secure the following power supply conditions (classic connection

| — 21 —

ABB-Welcome to ground, protective earthing, necessary additional measures, etc.).

Pos: 82 /Di nA4 - A nleitu ngen Onlin e/In halt/KNX/Do orEnt ry/M onta ge/ Mont age hinweis e - Allg emei n @ 1 9\m od_ 131 056 367 047 8_15 .docx @ 1 077 43 @ 2 @ 1

6.2

General installation instructions

• Terminate all branches of the wiring system via a connected bus device (e.g., indoor station, outdoor station, system device).

• Do not install the system controller directly next to the bell transformer and other power supplies (to avoid interf erence).

• Do not install the wires of the system bus together with 100-240 V wires.

• Do not use common cables for the connecting wires of the door openers and wires of the system bus.

• Avoid bridges between different cable types.

• Use only two wires for the system bus in a four-core or multi-core cable.

• When looping, never install the incoming and outgoing bus inside the same cable.

• Never install the internal and external bus inside the same cable.

6.3

Mounting

Pos: 85. 1 /DinA4 - Anleit ung en O nline/I nhal t/KNX/DoorE ntry/ 832 20-AP-xxx /Mo nta ge - Mo dule/ Mon tag e - Mon tage dos e -- 83 220 -AP-xxx @ 19\ mod _132 325 040 684 8_1 5.doc x @ 1 110 98 @ @ 1

The device M2302 must only be installed on mounting rails according to DIN EN 500022.

| — 22 —

ABB-Welcome

Pos: 83 /B usch-J aeg er (Neus truk tur )/M odul -Strukt ur/O nline -Doku me ntatio n/Steu er mod ule - Onlin e-Dok ume ntati on ( -- > F ür alle Dok ume nte <- -)/ +++ ++ ++ +++ ++ S eiten umb ruch + +++ ++ ++ +++ + @ 9\m od_ 126 8898 668 093 _0. docx @ 521 49 @ @ 1

| — 23 —

ABB-Welcome

Pos: 95 /Di nA4 - A nleitu ngen Onlin e/In halt/KNX/Do orEnt ry/Proj ektier ung -M erkbl att/Pr ojektie rPos: 9 7 /Busc h-Ja ege r (N eust ruktu r)/ Mo dul-Str uktu r/Onli ne-D oku ment ation /Rückseit en (-- > Für alle Dok um ente <- -)/R ückseit e - Bus ch-J aeg er - Allgem ein @ 20\ mod _13 273 200 748 86_1 5.d ocx @ 137 103 @ @ 1

Notice

=== E nde der Liste für Tex tma rke Ba ckcove r = ==

W e reserve the right to make technical changes at any time as well as changes in the content of this document without prior notice.

The detailed specifications agreed to at the time of ordering apply to all orders. ABB accepts no responsibility for possible errors or incompleteness in this document.

W e reserve all rights to this document and the topics and illustrations contained therein.

The document and its contents, or extracts thereof, must not be reproduced, transmitted or reused by third parties without prior written consent by ABB.