ABB 2CSY258712R0101 2CSY257532R0101 is a perimeter detector used to control doors, windows, and shutters. It detects the open or closed status through an internal reed switch and a magnet. The device is easy to install and can be programmed to work with a control unit.
Some of the key features of the ABB 2CSY258712R0101 2CSY257532R0101 perimeter detector include:
- Adjustable magnet opening and closing distance: The magnet opening distance can be adjusted between 15mm and 5mm, and the closing distance can be adjusted between 10mm and 5mm. This allows you to customize the detector to your specific needs.
advertisement
2CSYD0101B - 2CSYD0101M
Perimeter detector white - brown
EN
Installation manual
General description
The perimeter detector is a device used to control doors, windows and shutters in general. The device detects the open or closed status through an internal reed switch and a magnet.
- 1 -
Installation
The installation procedure encompasses the following steps:
1) Device and magnet fixing.
2) Programming.
3) Completion and test.
1. Device fixing
INSTRUCTIONS RELEVANT TO POSITIONING
The device should be installed (figure 1):
•
With the detector and the magnet aligned as shown in the figure;
•
With the detector fixed to the frame and the magnet fixed to the door, opposite to the hinges (if the door, or the window, has a double door, the magnet shall be positioned on the door that is opened first);
•
Far from electromagnetic sources (e.g. electricity meters, electric engines);
•
At distance of at least 1.5 meters from fluorescent lights.
In order to fix the detector (figure 2):
1) Open the device by removing the cover from the detector with a screwdriver.
2) Remove the battery block from the base by lifting it by the springs that hold the battery.
3) Fix the base with the provided screw anchors and screws.
4) Insert the battery block again into the base by paying attention that the lower tamper spring is correctly positioned in the proper hole of the base.
Figure 1
- 2 -
To fix the magnet (figure 3):
Figure 2
1) Remove the strip isolating the positive terminal of the battery.
The LED turns on and the 5-minute calibration time starts. It can be restarted by removing and re-inserting the battery.
2) Bring the magnet closer. When the LED turns off, it means that the reed contact is closed. Move the magnet to identify the end closing positions of the reed and fix the magnet between them (suggested distance 0.3+- 0.2 cm). To fix them, use two screws that are suitable for the existing frame type.
- 3 -
Figure 3
Magnet opening distance: 15 +- 5 mm
Closing distance: 10 +- 5 mm
2. Programming
To program the detector
1) Prepare the control unit to acquire the detector and select the required area and memory location.
2) Stimulate the detector by opening the door or the window equipped with the magnet or by pressing and releasing the antitampering tamper. The detector will transmit its code that will be acquired by the control unit.
3) The detector is programmed by setting the relevant parameters on the control unit. Besides the commands common to all sensors described in the installation manual of the control unit, it is possible to set also the following specific parameters:
(*) factory settings
PAR. VALUES
1
SI (YES)
(*)
NO
2
FUNCTION
Enabled channel (reed)
IMP
Disabled channel (reed)
Impulsive channel operation
BIS (*) Bistable channel operation
- 4 -
3. Completion and test
Lay the cover back on the compartment and test the detector by following the testing instructions in the installation manual of the control unit.
Maintenance
To clean the device externally, use a dry cloth.
Battery replacement
The battery in the detector shall not be disposed as urban waste
(Directive, 2006/66/EC), as it is subject to separate waste collection in order to avoid environmental damages.
Battery shall be replaced by qualified personnel.
To replace the battery:
1) Put the control unit into maintenance status (please refer to the installation manual of the control unit).
2) Open the detector.
3) Remove the exhausted battery.
4) Insert the new battery.
5) Close the detector.
6) Execute the test of the detector from the control unit to be sure that it works.
- 5 -
Device reset
To delete the acquisition address and to restore the factory configuration of the sensor, press the anti-opening tamper for 5 times with an interval of at least one second between each single pressing. The activity must be executed within 16 seconds.
The reset shall be carried out if you want that the device is acquired by another control unit. To re-acquire the device on the same control unit, it is not necessary to previously execute the reset procedure.
Package contents
no. 1 Perimeter detector no. 1 Magnet no. 1 Lithium battery 3 V – 1.4 Ah no. 2 self-tapping cross-recessed screws 2.9 x 27 mm no. 2 screw anchors
∅
5 mm no. 1 Manual
WARNING! Installation must be carried out only by a qualified electrician.
Perimeter detector
Product code 2CSYD0101B - 2CSYD0101M
Technical specifications
APPLICATION SCOPE
COMMUNICATION
TECHNOLOGY
RANGE IN FREE AIR
POWER SUPPLY
DETECTION ELEMENTS
SIGNAL ELEMENTS
Security
Transmission in FM 868.3 MHz
300 m
Lithium battery 3 V – 1.4 Ah lasting 5 years.
Operation is guaranteed for 30 days from the low battery notification
2 reeds
1 calibration LED
Low battery in the control unit (threshold
2.5V)
ANTI-TAMPERING PROTECTION Double tamper
EC Declaration of Conformity
ABB S.p.A., with registered office in Milan - via Vittor Pisani 16, declares under its own responsibility that the device with product code
2CSYD0101B - 2CSYD0101M meets the essential electromagnetic compatibility and security requirements contained in the Directive
R&TTE 1999/5/EC and in the EC Low Voltage Directive 2006/95/CE, as it was designed and manufactured in compliance with the following harmonized standards: EN 300 220, EN 50130-6, EN 50131-1,
EN 50131-2-6, EN 50131-5-3.
ABB S.p.A. reserve the right to change the product described in this manual at any time and without any advance notice.
Additional data provided by the manufacturer
USAGE TEMPERATURE -5 … + 45 °C
USAGE RELATIVE HUMIDITY
USAGE ENVIRONMENT
INSTALLATION
SIZES (L x H x W)
PERFORMANCE LEVEL
Max 95% max (non-condensing)
Indoor (sheltered and dry places)
Free
Detector 30 x 106 x 33 mm
Magnet
Compliant with the rules EN 50131-1 and
EN 50131-2-6 Class I – Grade 2
ABB S.p.A. - ABB SACE Division
Viale dell’Industria, 18
20010 Vittuone (MI) – Italy
Tel.: 02.9034.1
Telefax: 02.9034.7609
Printed in Italy
For further information: http://bol.it.abb.com, at
DomusTech section or call the free-phone number
Manual code 2CSM600502D0
2
01 rev 00
- 6 - 7 -
advertisement