Graco 3A5743C, Reactor E-8p and E-15p Portable Plural Component Sprayers Instructions

Add to my manuals
38 Pages

advertisement

Graco 3A5743C, Reactor E-8p and E-15p Portable Plural Component Sprayers Instructions | Manualzz

Instructions

Portable Plural Component Sprayer

E-8p and E-15p

3A5743C

EN

For spraying 1:1 mix ratio formulated no-heat polyurethane foams and dispensing 1:1 mix ratio polyurea joint-fill materials. For professional use only.

Not approved for use in European explosive atmosphere locations.

2000 psi (14 MPa, 138 bar) Maximum Working Pressure

See page 3 for a list of models.

Important Safety Instructions

Read all warnings and instructions in this manual before using this equipment.

Save these instructions.

WLD

2

Contents

Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Proportioners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Important Isocyanate (ISO) Information . . . . . . . . 7

Material Self-ignition . . . . . . . . . . . . . . . . . . . . . . 8

Keep Components A and B Separate . . . . . . . . . 8

Moisture Sensitivity of Isocyanates . . . . . . . . . . . 8

Foam Resins with 245 fa Blowing Agents . . . . . . 8

Changing Materials . . . . . . . . . . . . . . . . . . . . . . . 8

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Component Identification . . . . . . . . . . . . . . . . . . . 10

Controls and Indicators . . . . . . . . . . . . . . . . . . . . 11

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Electrical Requirements . . . . . . . . . . . . . . . . . . 12

Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Connect Fluid Hoses . . . . . . . . . . . . . . . . . . . . . 13

Connect Gun to Air Hose

(Air-Operated Guns Only) . . . . . . . . . . . . . . . . . 13

Connect Main Air Supply . . . . . . . . . . . . . . . . . 13

Flush Before Using Equipment . . . . . . . . . . . . . 13

Fill Wet-cups . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Recirculate Material . . . . . . . . . . . . . . . . . . . . . 15

Flush Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Spraying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Pressure Relief Procedure . . . . . . . . . . . . . . . . . . 18

Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Flushing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Status Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Control Board . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

120 V Fusion Air Purge System Packages . . . . 27

Suggested Spare Replacement Parts . . . . . . . . . 35

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Technical Specifications . . . . . . . . . . . . . . . . . . . . 37

Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 38

3A5743C

Systems

Systems

Model

E-8p

E-15p

Gun Model

Model

Fusion ® Air Purge

Part

247124

Proportioners

The model number, series letter, and serial number are located on the back of the system.

Model

E-8p

E-15p

Part

25N014

25N015

Part

25A836

26C023

Maximum Working

Pressure, psi (MPa, var)

2000 (14, 140)

Maximum Working

Pressure, psi (MPa, bar)

2000 (14, 140)

Proportioner

(see

Proportioners)

25A836

26C023

Volts

* Electrical

Connection

120 V 15 A cord

* See page 12 for detailed electrical requirements.

Related Manuals

Manuals are available at www.graco.com.

Manual in

English

313123

309577

309550

Description

Displacement Pump Repair-Parts

Displacement Pump Repair-Parts

Fusion AP Spray Gun Instructions-Parts

Related Proportioner

25A836

26C023

- - - - -

3A5743C 3

4

Warnings

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks.

When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings.

Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable.

ELECTRIC SHOCK HAZARD

WARNING

This equipment must be grounded .

Improper grounding, setup, or usage of the system can cause electric shock.

• Turn off and disconnect power cord before servicing equipment.

• Connect only to grounded electrical outlets.

• Use only 3-wire extension cords.

• Ensure ground prongs are intact on power and extension cords.

• Do not expose to rain. Store indoors.

TOXIC FLUID OR FUMES HAZARD

Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled or swallowed.

• Read Safety Data Sheets (SDSs) for handling instructions and to know the specific hazards of the fluids you are using, including the effects of long-term exposure.

• When spraying, servicing equipment, or when in the work area, always keep work area well-ventilated and always wear appropriate personal protective equipment. See Personal

Protective Equipment warnings in this manual.

• Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.

PERSONAL PROTECTIVE EQUIPMENT

Always wear appropriate personal protective equipment and cover all skin when spraying, servicing equipment, or when in the work area. Protective equipment helps prevent serious injury, including long-term exposure; inhalation of toxic fumes, mists or vapors; allergic reaction; burns; eye injury and hearing loss. This protective equipment includes but is not limited to:

• A properly fitting respirator, which may include a supplied-air respirator, chemically impermeable gloves, protective clothing and foot coverings as recommended by the fluid manufacturer and local regulatory authority.

• Protective eyewear and hearing protection.

3A5743C

Warnings

SKIN INJECTION HAZARD

WARNING

High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.

• Do not spray without tip guard and trigger guard installed.

• Engage trigger lock when not spraying.

• Do not point gun at anyone or at any part of the body.

• Do not put your hand over the spray tip.

• Do not stop or deflect leaks with your hand, body, glove, or rag.

• Follow the

Pressure Relief Procedure when you stop spraying and before cleaning, checking, or

servicing equipment.

• Tighten all fluid connections before operating the equipment.

• Check hoses and couplings daily. Replace worn or damaged parts immediately.

3A5743C

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. Paint or solvent flowing through the equipment can cause static sparking. To help prevent fire and explosion:

• Use equipment only in well-ventilated area.

• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop cloths (potential static sparking).

Ground all equipment in the work area. See Grounding

instructions.

• Never spray or flush solvent at high pressure.

• Keep work area free of debris, including solvent, rags and gasoline.

• Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes are present.

• Use only grounded hoses.

• Hold gun firmly to side of grounded pail when triggering into pail. Do not use pail liners unless they are anti-static or conductive.

• Stop operation immediately if static sparking occurs or you feel a shock .

Do not use equipment until you identify and correct the problem.

• Keep a working fire extinguisher in the work area.

PRESSURIZED ALUMINUM PARTS HAZARD

Use of fluids that are incompatible with aluminum in pressurized equipment can cause serious chemical reaction and equipment rupture. Failure to follow this warning can result in death, serious injury, or property damage.

• Do not use 1, 1, 1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents.

• Do not use chlorine bleach.

• Many other fluids may contain chemicals that can react with aluminum. Contact your material supplier for compatibility.

5

6

Warnings

WARNING

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.

• Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See

Technical Specifications in all equipment manuals.

Use fluids and solvents that are compatible with equipment wetted parts. See Technical

Specifications

in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information about your material, request Safety Data Sheets (SDSs) from distributor or retailer.

• Do not leave the work area while equipment is energized or under pressure.

Turn off all equipment and follow the Pressure Relief Procedure

when equipment is not in use.

• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufacturer’s replacement parts only.

• Do not alter or modify equipment. Alterations or modifications may void agency approvals and create safety hazards.

• Make sure all equipment is rated and approved for the environment in which you are using it.

• Use equipment only for its intended purpose. Call your distributor for information.

• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

• Do not kink or over bend hoses or use hoses to pull equipment.

• Keep children and animals away from work area.

• Comply with all applicable safety regulations.

MOVING PARTS HAZARD

Moving parts can pinch, cut or amputate fingers and other body parts.

• Keep clear of moving parts.

• Do not operate equipment with protective guards or covers removed.

• Pressurized equipment can start without warning. Before checking, moving, or servicing

equipment, follow the Pressure Relief Procedure and disconnect all power sources.

3A5743C

Important Isocyanate (ISO) Information

Important Isocyanate (ISO) Information

Isocyanates (ISO) are catalysts used in two component materials.

Isocyanate Conditions

Spraying or dispensing fluids that contain isocyanates creates potentially harmful mists, vapors, and atomized particulates.

• Read and understand the fluid manufacturer’s warnings and Safety Data Sheets (SDSs) to know specific hazards and precautions related to isocyanates.

• Use of isocyanates involves potentially hazardous procedures. Do not spray with this equipment unless you are trained, qualified, and have read and understood the information in this manual and in the fluid manufacturer’s application instructions and SDSs.

• Use of incorrectly maintained or mis-adjusted equipment may result in improperly cured material, which could cause off gassing and offensive odors. Equipment must be carefully maintained and adjusted according to instructions in the manual.

• To prevent inhalation of isocyanate mists, vapors and atomized particulates, everyone in the work area must wear appropriate respiratory protection. Always wear a properly fitting respirator, which may include a supplied-air respirator. Ventilate the work area according to instructions in the fluid manufacturer’s SDSs.

• Avoid all skin contact with isocyanates. Everyone in the work area must wear chemically impermeable gloves, protective clothing and foot coverings as recommended by the fluid manufacturer and local regulatory authority. Follow all fluid manufacturer recommendations, including those regarding handling of contaminated clothing. After spraying, wash hands and face before eating or drinking.

• Hazard from exposure to isocyanates continues after spraying. Anyone without appropriate personal protective equipment must stay out of the work area during application and after application for the time period specified by the fluid manufacturer. Generally this time period is at least 24 hours.

• Warn others who may enter work area of hazard from exposure to isocyanates. Follow the recommendations of the fluid manufacturer and local regulatory authority. Posting a placard such as the following outside the work area is recommended:

TOXIC FUMES

HAZARD

DO NOT ENTER DURING

SPRAY FOAM APPLICATION

OR FOR ___ HOURS AFTER

APPLICATION IS COMPLETE

DO NOT ENTER UNTIL:

DATE: ____________

TIME: ____________

3A5743C 7

8

Important Isocyanate (ISO) Information

Material Self-ignition

Some materials may become self-igniting if applied too thick. Read material manufacturer’s warnings and

Safety Data Sheets (SDSs).

Keep Components A and B

Separate

Cross-contamination can result in cured material in fluid lines which could cause serious injury or damage equipment. To prevent cross-contamination:

• Never interchange component A and component B wetted parts.

• Never use solvent on one side if it has been contaminated from the other side.

Moisture Sensitivity of

Isocyanates

Exposure to moisture (such as humidity) will cause ISO to partially cure, forming small, hard, abrasive crystal that become suspended in the fluid. Eventually a film will form on the surface and the ISO will begin to gel, increasing in viscosity.

NOTICE

Partially cured ISO will reduce performance and the life of all wetted parts.

• Always use a sealed container with a desiccant dryer in the vent, or a nitrogen atmosphere. Never store ISO in an open container.

• Keep the ISO pump wet cup or reservoir (if installed) filled with appropriate lubricant. The lubricant creates a barrier between the ISO and the atmosphere.

• Use only moisture-proof hoses compatible with

ISO.

• Never use reclaimed solvents, which may contain moisture. Always keep solvent containers closed when not in use.

• Always lubricate threaded parts with an appropriate lubricant when reassembling.

NOTE: The amount of film formation and rate of crystallization varies depending on the blend of ISO, the humidity, and the temperature.

Foam Resins with 245 fa

Blowing Agents

Some foam blowing agents will froth at temperatures above 90°F (33°C) when not under pressure, especially if agitated. To reduce frothing, minimize preheating in a circulation system.

Changing Materials

NOTICE

Changing the material types used in your equipment requires special attention to avoid equipment damage and downtime.

• When changing materials, flush the equipment multiple times to ensure it is thoroughly clean.

• Always clean the fluid inlet strainers after flushing.

• Check with your material manufacturer for chemical compatibility.

• When changing between epoxies and urethanes or polyureas, disassemble and clean all fluid components and change hoses. Epoxies often have amines on the B (hardener) side. Polyureas often have amines on the B (resin) side.

3A5743C

Overview

Overview

The system is a portable, electric-powered, 1:1 mix ratio proportioner. It is for use with formulated no-heat polyurethane foams that may be applied with impingement mix spray guns and for use with polyurea joint fill materials that may be applied with static mix guns.

Severe duty, positive displacement reciprocating piston pumps meter fluid flow to the gun for mixing and applying. When set to recirculation mode, the system will circulate fluids back to the supply pails.

An electronic processor controls the motor, monitors fluid pressures, and alerts the operator if errors occur.

See STATUS Indicator , page 11, for further

information.

The system has two recirculation speeds: slow and fast, and an adjustable pressure/flow output.

Slow Recirculation

• Use for pump priming.

Fast Recirculation

• Use for flushing.

• Use for pump priming.

Output Adjust

Automatically maintains selected pressure/flow output for spraying.

3A5743C 9

Component Identification

Component Identification

/

/

$

3

0

F IG . 1: Component Identification

Key:

A Pump A

B Pump B

C Fluid Pressure Gauges

D Spray and Overpressure Relief Valves

E Control Panel

F Electric Motor and Drive Housings

*

G Hose Bundle

H Spray Gun

J Recirculation Outlet

L Outlet Hose Connections

M Power Cord

P Fluid Inlet

+

(

WLD

%

-

)

10 3A5743C

Controls and Indicators

Controls and Indicators

Motor/Pump Control Function Knob

Status

Codes

+

-

Status Indicator

Power

Switch

-

-

TI17123b

F IG . 2: Controls and Indicators

Power Switch

Powers the system on and off.

Motor/Pump Control Function Knob

Use the knob to select desired function.

Icon Setting

Park

Function

Stops motor and automatically parks pumps.

Slow Recirc Slow recirculation speed.

Fast Recirc Fast recirculation speed.

Static Mix

Spray

Use fluid flow settings 1-5 to dispense polyurea joint-fill materials through a static mixer.

Use fluid pressure settings

6-10 to spray polyurethane foam.

STATUS Indicator

Indicates the system status, including power and error codes.

• Indicator steady on: power switch is turned on.

• Indicator blinking: If an error occurs, the status indicator light will blink one to seven times to indicate a specific status code, pause, and then repeat. The following table provides a brief description of each status code. For more detailed

information and corrective action, see Status

Codes on page 21.

Table 1: Status Codes

(also located on the front of the Reactor)

Code Code Name

6

7

4

5

1

2

3

Pressure imbalance between A and B sides

Unable to maintain pressure setpoint

Pressure transducer A failure

Pressure transducer B failure

Excessive current draw

High motor temperature

No cycle counter switch input

NOTE: The default is to shut down if a status code indication occurs. Codes 1 and 2 may be set to disable automatic shutdown if desired; see page 22. You cannot set the other codes.

3A5743C 11

Setup

Setup

Location

• The system should always be used on a level surface.

• Do not expose the system to rain.

Grounding

Electrical Requirements

• Required power source: single dedicated circuit that is rated at a minimum of 15A.

NOTE: Cords must be 3-conductor grounded, rated for your environment.

• Power cord connector (120V):

One NEMA 5-15T

• Extension cord requirements:

Required Wire Size

Up to 50 ft (15 m)

AWG 14

Up to 100 ft (30 m)

AWG 12

The equipment must be grounded to reduce the risk of static sparking and electric shock. Electric or static sparking can cause fumes to ignite or explode.

Improper grounding can cause electric shock.

Grounding provides an escape wire for the electric current.

System: grounded through power cord.

Generator (if used): follow your local code and manufacturer’s recommendations. Start and stop the generator with power cord(s) disconnected.

Spray gun: ground through connection to a properly grounded fluid hose and system.

Fluid supply container: follow local code.

Object being sprayed: follow local code.

Solvent pails used when flushing: follow local code.

Use only conductive metal pails, placed on a grounded surface. Do not place the pail on a nonconductive surface, such as paper or cardboard, which interrupts grounding continuity.

To maintain grounding continuity when flushing or relieving pressure: hold metal part of the spray gun firmly to the side of a grounded metal pail, then trigger the gun.

12 3A5743C

Setup

Connect Fluid Hoses

Connect the fluid supply hoses to outlet hose connections (F IG . 3). Red hoses for component A (ISO), blue for component B (RES). Fittings are sized to prevent connection errors. Connect the other end of hoses to A and B inputs of the gun.

NOTICE

To prevent pressure fluctuations and equipment damage, only operate equipment with fluid supply hoses longer than 25 ft.

Connect Gun to Air Hose

(Air-Operated Guns Only)

Connect the gun air hose to the gun air input and to the air filter outlet. If you are using more than one hose bundle, join the air hoses with the nipple provided with the hose bundle.

Connect Main Air Supply

The system requires 4 scfm (0.112 m 3 /min) compressed air for the air operated spray guns to work correctly.

Connect the main air supply to the quick disconnect fitting on the unit. The air supply hose must be at least

5/16 in. (8 mm) ID up to 50 ft (15 m) or 3/8 in. (10 mm)

ID up to 100 ft (30 m).

Flush Before Using Equipment

The equipment was tested with lightweight oil, which is left in the fluid passages to protect parts. To avoid contaminating your fluid with oil, flush the equipment with a compatible solvent before using the equipment.

See

Flushing , page 19.

B (RES) Blue

A (ISO) Red

Compressed Air Line

WLD

A (ISO) Red

Air

B (RES) Blue

F IG . 3 Hose and Air Connections

3A5743C 13

Setup

Fill Wet-cups

Keep the felt washers in the pump wet-cups saturated with ISO pump oil. The lubricant creates a barrier between the ISO and the atmosphere.

Fill wet-cups through the slots in the plate, or remove a screw and swing the plate to the side.

Slots

The pump rod and connecting rod move during operation. Moving parts can cause serious injury such as pinching or amputation. Keep hands and fingers away from the wet-cup during operation. Shut off power before filling the wet-cup.

F IG . 4 Fill Wet Cup

TI17124a

14 3A5743C

Setup

Recirculate Material

The system circulates material from the fluid manifold back to the supply container.

5. Set the Spray valves to Recirc.

1. Insert inlet tubes into the pails.

2. Set the function knob to Park .

+

-

F IG . 5 Set the Function Knob to Park

TI17127b

3. Plug in the power cord.

4. Turn on the power.

F IG . 7 Set the Spray Valves to Recirc.

TI17133a

6. Set the function knob to Slow Recirc

Recirc .

or Fast

+

-

OR +

-

TI17128b

F IG . 8 Set the Function Knob to Slow or Fast Recirc.

7. When material exits both recirculation tubes, set the function knob to Park .

8. Set the Spray valves to Spray.

F IG . 6 Turn on the Main Power

TI17134a

F IG . 9 Set the Spray Valves to Spray

TI17132a

3A5743C 15

Setup

Flush Fluid

1. Insert inlet tubes into pails of solvent.

2. Insert recirculation tubes into waste containers.

3. Set the function knob to Park. See F IG . 5, page 15.

4. Plug in the power cord.

5. Turn on the power. See F IG . 6, page 15.

6. Set the Spray valves to Recirc. See F IG . 7, page 15.

7. Set the function knob to Slow Recirc or Fast

8. When clean solvent exits both recirculation tubes, set the function knob to Park .

9. Insert inlet tubes into the material containers.

10. Set the Spray valves to Spray. See F IG . 9, page 15.

11. Run until material exits the gun manifold.

16 3A5743C

Spraying

Spraying

For air operated guns , air is supplied to spray gun with the gun piston safety lock engaged and gun fluid manifold valves A and B closed (if present).

In this example, the B side pressure is higher, so use the B side valve to balance pressures.

Ti17137a

F IG . 12 Balance the Pressure

NOTE: Watch the gauges for 10 seconds to ensure pressure holds on both sides and pumps are not moving.

7. Open the gun fluid manifold valves A and B

(impingement mix guns only).

F IG . 10 Engage the Safety Lock and Fluid Manifold

1. Set the function knob to Park. See F IG . 5, page 15.

2. Engage the piston safety lock.

3. Open the gun manifold.

4. Set the Spray valves to Spray. See F IG . 9, page 15.

5. Turn the pressure control knob to the right until the fluid pressure gauges show desired pressure.

NOTE: Use lower pressure for joint filling applications.

F IG . 13 Open the Fluid Manifold

NOTICE

On impingement guns, never open the fluid manifold valves or trigger the gun while pressures are imbalanced. Opening the valves or triggering the gun during a pressure imbalance can cause material crossover in the gun, leading to equipment damage.

+

-

TI17129b

F IG . 11 Lower the Pressure

6. Check fluid pressure gauges to ensure proper pressure balance. If imbalanced, reduce the pressure of the higher component by slightly turning the Spray valve for that component toward Recirc, until the gauges show balanced pressures.

NOTE: The pressure imbalance alarm (Status Code 1) is inactive for 10 seconds after entering spray pressure mode, to allow time to balance pressures.

8. Disengage the piston safety lock.

F IG . 14 Disengage the Safety Lock

9. Test spray onto cardboard or a plastic sheet. Verify that the material fully cures in the required length of time, and is the correct color. Adjust the pressure and temperature to get desired results. The equipment is ready to spray.

3A5743C 17

Pressure Relief Procedure

Pressure Relief

Procedure

Follow the Pressure Relief Procedure whenever you see this symbol.

Shutdown

For longer breaks (more than 10 minutes), use the following procedure. If the equipment will be shut down for more than three days, perform the

Flushing procedure, page 19, first.

1. Relieve the pressure. Follow the

Pressure Relief

Procedure , page 18.

2. Close gun fluid valves A and B. Doing this will keep the internal parts of the gun cleaner and prevent crossover.

This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from pressurized fluid, such as skin injection, splashing fluid and moving parts, follow the Pressure Relief

Procedure when you stop spraying and before cleaning, checking, or servicing the equipment.

1. Perform the gun pressure relief procedure. Refer to your separate spray gun manual.

2. Set the function knob to Park

.

See

F IG . 5, page 15.

3. Turn the Spray valves to Recirc. See F IG . 7, page

15. Fluid will be returned to the material pails. The

pumps will move to the bottom of their stroke.

Ensure that the gauges drop to 0.

F IG . 15 Close the Fluid Valves

3. Shut off the power.

TI17135a

F IG . 16 Turn off the Power

4. Perform the gun shutdown procedure. Refer to your separate spray gun manual.

5. Wrap the hoses around the sprayer.

18 ti33432a

F IG . 17 Wrap the Hoses Around the Sprayer

6. Disconnect the power cord before moving.

3A5743C

Maintenance

Maintenance

• Check the pump wet-cups fluid level daily. Refer to

Fill Wet-cups , page 14.

• Do not overtighten the packing nut/wet-cup. The throat u-cup is not adjustable.

• Keep component A from exposure to moisture in the atmosphere to prevent crystallization.

• Generally, flush if you will shutdown for more than three days. Flush more often if material is moisture sensitive and humidity is high in the storage area, or if material may separate or settle out over time.

• Close gun fluid valves A and B when not spraying.

See F IG . 15, page 18. Doing this will keep the

internal parts of the gun cleaner and prevent crossover. See spray gun manual.

• Always grease the gun after use. See your spray gun manual.

Flushing

Flush equipment only in a well-ventilated area. Do not spray flammable fluids.

• Generally, flush if you will be shut down for more than three days. Flush more often if material is moisture sensitive and humidity is high in the storage area, or if material may separate or settle out over time.

• Flush out old fluid with new fluid, or flush out old fluid with a compatible solvent before introducing new fluid.

• Use the lowest possible pressure when flushing.

• Always leave some type of fluid in system. Do not use water.

• For long term storage, flush out the solvent with a storage fluid or, at minimum, clean motor oil.

1. Engage the piston safety lock or trigger safety lock.

Close fluid valves A and B. See F IG . 10, page 17.

Leave air on.

2. Set the function knob to Park. See F IG . 5, page 15.

3. Remove both recirculation tubes from the material containers and secure each one to a dedicated waste container.

4. In the material containers, pull the fluid inlet tubes out of the material.

5. Turn the Spray valves to Recirc. See F IG . 7, page

15.

6. Set the function knob to Fast Recirc

. See F IG .

8, page 15. Pump material from the fluid inlet tubes

until no more comes out.

7. Set the function knob to Park

page 15.

. See F IG . 5,

3A5743C 19

Maintenance

8. Remove the fluid inlet tubes from the material containers and place the tubes in the solvent containers.

9. Set the function knob to Fast Recirc

. See F IG .

8, page 15. Pump solvent through system into the

waste containers.

10. When nearly clear solvent exits the recirculation tubes, set the function knob to Park

5, page 15.

. See F IG .

NOTE: To flush the spray gun, refer to your separate spray gun instruction manual.

11. Purge the gun hoses.

a. Disconnect the hoses from the gun and secure to a pail of solvent.

b. Turn Spray valve A to Spray. See F IG . 9, page

15.

c. Open the gun into waste container A.

d. Set the function knob to Slow Recirc

the hose is flushed. See F IG . 9, page 15.

until e. Set the function knob to Park

page 15.

f.

Repeat for B side.

. See F IG . 5,

12. Set the function knob to Park

page 15.

. See F IG . 5,

13. Solvent flushing is a two step process. Go back to step 3, drain solvent, and flush again with fresh solvent.

14. Place the fluid inlet tubes in a pail of plasticizer or clean motor oil and circulate fluid through the system. Leave fluid in the unit.

NOTE: Never leave the unit dry unless it has been disassembled and cleaned. If fluid residue dries in the pumps, the ball checks may stick the next time you use the unit.

20 3A5743C

Troubleshooting

Troubleshooting

Status Codes

Determine the status code by counting the number of times the status indicator blinks.

-

-

STATUS Indicator

TI17123b1

F IG . 18 The Status Indicator

Status Code 1: Pressure Imbalance

NOTE: The unit does not check for pressure imbalance at setpoints less than 250 psi (1.75 MPa, 17.5 bar). The unit does not check for pressure imbalance for 10 seconds after entering pressure mode.

The unit senses pressure imbalance between components A and B, and warns or shuts down, depending on settings of DIP switches 1 and 2. To turn off automatic shutdown and/or tighten pressure tolerances for status code 1, see Status Code 1 and 2

Settings .

1. Check the fluid supply of the lower pressure component and refill if necessary.

2. Reduce the pressure of the higher component by slightly turning the Spray valve for that component toward Recirc, until the gauges show balanced

pressures. See F IG . 12, page 17.

NOTE: Turn the Spray valve only enough to balance pressure. If turned completely, all pressure will bleed off.

3. Check the fluid inlet strainers and fluid filters at the gun.

Status Code 2: Pressure Deviation from

Setpoint

The unit does not check for pressure deviation at setpoint less than 400 psi (2.8 MPa, 28 bar).

The unit senses pressure deviation from a setpoint, and warns or shuts down, depending on settings of DIP switches 3 and 4. If equipment cannot maintain enough pressure for a good mix at the gun, try using a smaller mix chamber or nozzle.

To turn off automatic shutdown and/or tighten pressure tolerances for status code 2, see Status Code 1 and 2

Settings .

3A5743C 21

Troubleshooting

Status Code 1 and 2 Settings

1. Locate switch SW2 on the control board.

2. Set the four DIP switches to the desired positions.

See F IG . 19 and Table 2.

OFF

3

4

1

2

TI7023a

3

4

1

2

F IG . 19 DIP Switch (SW2) Settings

ON

(Default)

TI7024a

Table 2: Status Code 1 and 2 Settings

DIP Switch and Function

DIP Switch 1

If selected, causes shutdown or displays an advisory if the pressure imbalance exceeds selection made in DIP Switch 2

DIP Switch 2

If selected, causes shutdown if A and B pressure imbalance is greater than

If selected, causes greater than advisory if A and B pressure imbalance is

Left

ADVISORY

500 psi (3.5 MPa, 35 bar)

(60% if < 800 psi [5.6

MPa, 56 bar] running)

300 psi (2.1 MPa, 21 bar)

(50% if < 800 psi [5.6

MPa, 56 bar] running)

DIP Switch 3

If selected, causes shutdown or displays an advisory due to deviation of pressure from setpoint exceeds selection made in

DIP Switch 4

DIP Switch 4

Causes advisory if deviation of pressure from setpoint is greater than

ADVISORY

300 psi (2.1 MPa, 21 bar)

(25% if < 800 psi [5.6

MPa, 56 bar])

Right (default setting)

SHUTDOWN

800 psi (5.6 MPa, 56 bar)

(70% if < 800 psi [5.6

MPa, 56 bar] running)

500 psi (3.5 MPa, 35 bar)

(60% if < 800 psi [5.6

MPa, 56 bar] running)

SHUTDOWN

500 psi (3.5 MPa, 35 bar)

(40% if < 800 psi [5.6

MPa, 56 bar])

Status Code 3: Transducer A Failure

1. Check transducer A electrical connections (J3) at

the board, page 25.

2. Reverse A and B transducer electrical connections

at the board, F IG . 21, page 25. If the error moves to

transducer B (Status Code 4), replace transducer A,

Control Board , page 24.

Status Code 4: Transducer B Failure

1. Check transducer B electrical connections (J8) at

the board, F IG . 21, page 25.

2. Reverse A and B transducer electrical connections

at the board, F IG . 21, page 25. If the error moves to

transducer A (Status Code 4), replace transducer B,

Control Board , page 24.

Status Code 5: Excessive Current Draw

Shut off the unit and contact your distributor before resuming operation.

1. Locked rotor: motor unable to turn. Replace the motor.

2. Short on control board. Replace the board,

Control

Board Replacement , page 24.

3. Worn or hung up motor brush causing arching of brush at commutator. Replace the brushes.

22 3A5743C

Troubleshooting

Status Code 6: High Motor Temperature

The motor is running too hot.

1. The motor temperature too high. Reduce pressure duty cycle, gun tip size, or move system to a cooler location. Allow 1 hour for cooling.

2. Check fan operation. Clean the fan and motor housing.

Status Code 7: No Cycle Counter Switch

Input

Have not received input from the cycle counter switch for 10 seconds after selecting Recirculation Mode.

1. Check the cycle counter switch connection to the

board (J10, pins 5, 6), F IG . 21, page 25 (figure

control module wiring connections).

2. Check that the magnet (224) and cycle counter switch (223) are in place under the B side motor end cover (227). Replace if necessary.

3A5743C 23

Repair

Repair

Control Board

Power Bootup Check

There is one red LED (D11) on the board. Power must

be on to check. See F IG . 21 for location. Function is:

• Startup: 1 blink for 60 Hz, 2 blinks for 50 Hz.

• Motor running: LED on.

• Motor not running: LED off.

• Status code (motor not running): LED blinks status code

Control Board Replacement

Check motor before replacing board.

1. Relieve the pressure. Follow the Pressure Relief

Procedure , page 18.

2. Carefully lay the sprayer on its side on a level surface. Rotate the sprayer and rest upside-down on blocks.

NOTE: Always use two people when lifting the sprayer on to a workbench.

3. Remove the four screws (10) and control board cover (61) to expose the control board (12).

4. Disconnect all cables and connectors from the board.

5. Remove the seven screws (13) and remove the board.

6. Install the new board in reverse order.

NOTE: Apply thermal compound between the square steel piece on the back of the board and the main aluminum plate.

Board

Jack

J1

J2

J3

J4

J7

J8

J9

J10

J11

Table 3: Control Board Connectors

(see F IG . 21)

Pin Description n/a Main power from breaker n/a n/a

Function knob

Transducer A n/a Motor power (230 V units)

1, 2 Motor thermal overload signal n/a n/a

Transducer B

Fan

1, 2 Status Indicator

3, 4 Not used

5, 6

7, 8

Cycle switch signal

Jumpered

9, 10 Jumpered n/a Motor power (120 V)

10 (x4)

61

12

13 (x7)

WLD

F IG . 20 Control Board Removal

24 3A5743C

Repair

LINE

P1

P2

Motor

Fan

Black Twin Flat Cable

Red

Black

J9

Yellow

Cycle

Counter

Yellow

Red

Black

Status

Indicator

Black

Black Sheath

Jumper

White

Jumper

1

9

10

6

7

8

4

5

2

3

J1

J7

J10

OFF

1

2

3

4

J11

(120 V Board)

CONTROL

BOARD

25N033 (120 V)

ON

SW2 (see page 22 to adjust settings) not used

Black

Red

White

J2

J8 J3

Black Sheath

Function

Knob

Pressure Transducer A

Black Phone Cable and Plug

Pressure Transducer B

F IG . 21 Control Module Wiring Connections

3A5743C 25

Repair

26 3A5743C

Parts

120 V Fusion Air Purge System Packages

Parts

WLD

101

System

Package Volts Description

25N014

25N015

120 V

Fusion Air Purge Proportioner Packages for E-8p

Fusion Air Purge Proportioner Packages for E-15p

Bare Proportioner

(101)

25A836

26C023

Gun

(103)

247124

103

3A5743C 27

Parts

25A836 and 26C023, Bare Proportioner

WLD

28

1

2

3

Apply sealant to threads.

Apply sealant to all non-swiveling pipe threads.

Apply lubricant to all o-rings and bolt-wheel connection (3, 91).

4

5

Cover entire surface of sensor probe with lubricant before assembling onto motor plate (8).

Torque to 5-6 ft-lb (6.7-8 N•m).

3A5743C

25A836 and 26C023, Bare Proportioner (continued)

A

Parts

A

WLD

3A5743C

WLD

29

Parts

25A836 and 26C023, Bare Proportioner (continued)

0$1,)2/'$&&25',1*/<

25,(1735(6685(

0$1,)2/'$&&25',1*/<

( )

25,(1735(6685(

'(7$,/&

6(('(7$,/%

'(7$,/%

D

6(('(7$,/

&

A

D

B

E 6

6(('(7$,/

$

35(6685($

327(17,20(7(5

35(6685(%

32:(5

PIN 1 - J UMPER

PIN 2 - J UMPER

PIN 3 - J UMPER

PIN 4 - J UMPER

PIN 5 - CYCLE COUNTER

PIN 6 - CYCLE COUNTER

PIN 7 - NOT USED

PIN 8 - NOT USED

PIN 9 - DISPLAY LED

PIN 10 - DISPLAY LED

B

LA

C

K W

IRE

RED

W

IRE

*5281'

027257+(50$/

<(//2:

0272532:(5287

5('$1'%/$&.

8

02725)$1

WLD

'(7$,/$

30 3A5743C

Parts

25A836 and 26C023, Bare Proportioner (continued)

Ref. Part Description

3

4

1

2

5

24J139 CART, painted

16H888 GROMMET, push-in, 7/8 id

16F820 WHEEL, caster

16H352 SPACER, axle

7

121573 BUMPER, urethane, 3/8-16, 80-90 dur

120454 WASHER, flat

8 16G939 PLATE, motor mount

10 117493 SCREW, mach, hex washer hd

11 102040 NUT, lock, hex

12 25N033 BOARD, circuit assy

13 107156 SCREW, mach, pan hd

14 24K983 SWITCH, rocker, w/breaker, 240V,

20A

15 119930 DIODE, light-emitting

16 24L002 POTENTIOMETR, adjustment, pressure

17 119897 FITTING, bulkhead, cable, 0.250

18 24K995 CORD SET, power, 125V

19 15G230 CABLE, harness, power

20 15C866 WIRE, jumper

21 116773 CONNECTOR, plug, 3.81 mm (10 position)

22 15G053 PLATE, detent, display

23 24L001 KNOB, control, w/ball plunger

27 24J147 MANIFOLD, recirculation

28 24J140 BRACKET, recirc mnfld, painted

29 115492 SCREW, mach, slot hex wash hd

30 108296 SCREW, mach, hex wash hd

31 156971 FITTING, nipple, short

32 155541 FITTING, swivel, 90 degree

33 15G292 MANIFOLD, pressure transducer

34 116704 ADAPTER, 9/16-18 jic x 1/4 npt

Qty.

2

1

1

1

2

1

1

1

1

1

1

1

7

1

6

1

4

1

8

1

10

2

2

1

1

1

2

2

2

Ref. Part Description

35 24K999 TRANSDUCER, pressure, control

36 16H530 TUBE, fluid

45 249629 HOSE, cpld, 1/4" x 48", moistgard

46 249630 HOSE, cpld, 1/4" x 48", resin

58 103473 STRAP, tie, wire

61 24J141 COVER, electronics, painted,

E-8P

62 24J151 COVER, shroud, front, painted

63 24J152 COVER, shroud, back, painted

67  16H569 LABEL, warning

85 16H543 HANDLE, pull

86 121114 NUT, hex, self locking

87 261866 WASHER, flat

90 112154 PIN, straight, slotted

91 15M314 SCREW, cap

92  189930 LABEL, caution

93  16H902 TAG, informational

94 15G458 CABLE, fan, 46" w/plug/board conn

96 217374 LUBRICANT, ISO pump

98 113505 NUT, keps, hex hd

99 26A503 PROPORTIONER, 120V, E-15P,

OEM

25A835 PROPORTIONER, 120 V, E-8p,

OEM

102 17L272 PLUG, rubber

103* 119992 FITTING, pipe, nipple, 3/4 x 3/4 npt

Qty.

1

1

2

2

4

1

1

2

2

1

1

1

2

2

2

1

1

1

1

1

1

1

1

 Replacement safety labels, tags, and cards are available at no cost.

* Only used with Reactor E-8p (25A836).

3A5743C 31

Parts

25A836 and 26C023, Bare Proportioner

LQPP

IURPLQVLGHERWWRPHGJH

LQPP

IURPLQVLGHHGJH

WLD

1 Apply lubricant to all gear teeth, motor pinion, and motor end bell on both sides of the motor.

2 Apply lubricant to rectangular cavity on connecting link.

3 Apply lubricant to threads of cylinder before assembly into housing.

4 Torque to 150+/-10 in-lb.

5 Tighten by hand only.

6 Torque fasteners to 30-35 in-lb. Applies only when fasteners are assembled in plastic housings (215).

7 Switch mounts to cover opposite brush end of motor only.

8

9

10

Housing must be installed on motor with crankshafts aligned with each other.

Assemble magnet to center of offset crankshaft on switch cover side of motor and adjust for park location.

Affix switch to motor cover with double-sided tape. Cut to 2 in.

(51 mm). Mount cover on side opposite the brush end of motor.

32 3A5743C

Parts

Ref. Part Description

201 24E355 MOTOR, 120V

202 24K985 FAN, cooling, 120 VAC

203 115836 GUARD, finger

204 103646 RIVET, blind

205 120094 SCREW, pan hd, phil, zinc

207‡ 115492 SCREW, mach, slot hex wash hd

208* 116074 WASHER, thrust

209* 107434 BEARING, thrust

210* 248231 CRANK, 595

211* 180131 BEARING, thrust

212 116073 WASHER, thrust

213 116079 BEARING, thrust

214 249194 GEAR, reducer (first stage)

215 26A505 HOUSING, drive, assembly,

E-15p

‡ 287000 HOUSING, drive, assembly, E-8p

216  287053 ROD, connecting

217  196762 PIN, straight

218 17A257 NUT, jam, pump, E-15p

Qty.

2

4

2

2

2

2

2

2

3

8

1

1

1

1

2

2

2

2

Ref. Part Description

195150 NUT, jam, pump, E-8p

219 245970 PUMP, displacement, E-15p

24L006 PUMP, displacement, E-8p

220‡ 117493 SCREW, mach, hex washer hd

221 15B254 COVER, front, Graco, paint

222‡ 15B589 COVER, pump rod

223 117770 SWITCH, reed w/cable

224 24K982 MAGNET, disc, 0.38 dia, 0.100 thick

227 115711 TAPE, foam, 1/2 wide

228 119997 INSERT, thread, knock-in, 8/32 unc

229 15F849 LABEL, side, Reactor, Graco

* Included in 248231 Crankshaft Kit.

‡ Included in 287055 Drive Housing Kit.

 Included in 287053 Connecting Rod Kit.

Qty.

1

1

2

2

2

8

2

2

1

1

2

3A5743C 33

Parts

Recirculation Manifold, 24J147

507

3

506

505a 3

505b

3

504

3

503

1 2 3

503a

4

503b

4

501

502

Ref. Part Description

501 24K993 MANIFOLD, recirculation

502 111763 ELBOW; 1/4 npt (mbe)

503 239914 VALVE, Spray; includes items

503a, 503b

503a 15E022 SEAT, valve

503b 111699 GASKET, seat, valve

504 224807 BASE, valve

505a 17X499 HANDLE, valve, drain (Red)

505b 17X521 HANDLE, valve, drain (Blue)

506 111600 PIN, grooved

507 113641 GAUGE, pressure, fluid

508 116504 TEE; 1/4 npt(m) x 1/4 npt(f) run;

1/4 npt(f) branch

509 119998 ADAPTER; 5/16 JIC x 1/4 npt(m)

510 116704 ADAPTER; 3/8 JIC x 1/4 npt(m)

511 556765 ELBOW, tube; 1/4 npt(m) x 3/8 in.

(10 mm) OD tube

515 156823 UNION, swivel; 1/4-18 npt

Qty.

1

4

2

2

1

1

2

2

2

1

2

2

1

1

1

510

508

511 515

509

TI17460a

3

4

1

2

Torque to 250 in-lb (28 N•m).

Use blue threadlocker on valve cartridge threads into manifold.

Apply lubricant to mating surfaces.

Part of item 503.

34 3A5743C

Suggested Spare

Replacement Parts

Part Description

24K983 SWITCH, motor power, with circuit breaker

113641 GAUGE, pressure, fluid; sst

239914 VALVE, Spray; includes seat and gasket

24L002 POTENTIOMETER, control knob

24K999 TRANSDUCER, pressure

24L006 PUMP, displacement; fits either side, E-8p only

249855 REPAIR KIT, displacement pump; includes seals, balls, bearings, intake valve seat)

Suggested Spare Replacement Parts

Accessories

Fusion Air Purge Gun

Air purge gun, available in round or flat patterns. See your gun manual.

3A5743C 35

Dimensions

Dimensions

LQ

FP

LQ

FP

WLD

LQ

FP

36 3A5743C

Technical Specifications

Technical Specifications

Reactor E-8p and E-15p

Maximum fluid working pressure

Electrical requirements

Generator Size

Minimum hose length

Maximum Ambient Temperature

Overpressure Relief

Maximum Output at 340 cycles/min

E-8p

E-15p

Output per Cycle (A and B)

E-8p

E-15p

Sound Pressure

In fast circulation mode

At 2000 psi (14 MPa, 138 bar), 0.72 gpm (2.7 lpm)

Sound Pressure per ISO 9614-2

In fast circulation mode

At 2000 psi (14 MPa, 138 bar), 0.72 gpm (2.7 lpm)

Inlet/Outlet Sizes

Fluid Outlet - Component A (ISO)

Fluid Outlet - Component B(RES)

Fluid Circulation Return - Component A (ISO)

Fluid Circulation Return - Component B(RES)

Air Inlet

Air Outlet

Hose Markings

A Side

B Side

Weight (empty), without gun and hose

Wetted Parts

Maximum Hose Length

US

2000 psi

Metric

14 MPa, 138 bar

120 Vac, 1 phase, 50/60 Hz, 1800 W; requires a single dedicated 15 A circuit

2500 W minimum

25 ft

110°F

7.6 m

43°C

Spray valves automatically relieve excessive fluid pressure back to supply tanks

12 lb/min

15 lb/min

0.00352 gal.

0.0044 gal.

78.7 dB(A)

84.5 dB(A)

88.6 dB(A)

94.4 dB(A)

-5 JIC male

-6 JIC male

-5 JIC male

-6 JIC male

1/4 in. quick-disconnect industrial type pin fitting

1/4 npsm(m)

Red

5.4 kg/min

6.8 kg/min

0.0133 liter

0.0167 liter

Blue

95 lb.

43.1 kg

Aluminum, stainless steel, carbon steel, brass, carbide, chrome, chemically resistant o-rings, PTFE, ultra-high molecular weight polyethylene

105 ft 32 m

3A5743C 37

Graco Standard Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by

Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT

LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE .

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy

(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT

MANUFACTURED BY GRACO . These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.

Graco Information

For the latest information about Graco products, visit www.graco.com

.

For patent information, see www.graco.com/patents .

TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.

Phone: 612-623-6921 or Toll Free: 1-800-328-0211, Fax: 612-378-3505

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

Original instructions.

This manual contains English. MM 3A5743

Graco Headquarters: Minneapolis

International Offices: Belgium, China, Japan, Korea

GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA

Copyright 2018, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.

www.graco.com

Revision C , June 2019

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals