Graco 332456D, Pump Expansion Kits Owner's Manual

Add to my manuals
40 Pages

advertisement

Graco 332456D, Pump Expansion Kits Owner's Manual | Manualzz

Installation-Parts

To includes

Important

Read all warnings and instructions in this manual and in your PD2K manual. Save these instructions.

See page 3 for model part numbers and approvals information.

332456D

EN

PROVEN QUALITY. LEADING TECHNOLOGY.

Related Manuals ................................................ 2

Models............................................................... 3

Warnings ........................................................... 3

Important Isocyanate (ISO) Information ................ 6

Isocyanate Conditions .................................. 6

Material Self-ignition..................................... 6

Keep Components A and B Separate ............ 6

Moisture Sensitivity of Isocyanates................ 6

Changing Materials ...................................... 7

Important Acid Catalyst Information ..................... 8

Acid Catalyst Conditions............................... 8

Moisture Sensitivity of Acid Catalysts ............ 8

Installation.......................................................... 9

Before Installing the Kit................................. 9

Install the Frame .......................................... 10

Install the Wall Bracket ................................. 11

TSL Cup Kit ................................................. 12

Fluid Connections ........................................ 15

Electrical Connections .................................. 16

Grounding ................................................... 18

Complete the Installation .............................. 19

Repair................................................................ 21

Dose Valve Tubing Connections ................... 21

Replace Pump Control Module ..................... 23

Electrical Schematics .......................................... 24

Standard Models (MC1000, MC2000,

MC3000, MC4000) ......................... 24

Dual Panel Models (MC1002, MC2002,

MC4002)........................................ 30

Pump Expansion Kit Parts................................... 36

Technical Data ................................................... 39

California Proposition 65 ..................................... 39

Manual No.

Description

3A2800 PD2K Proportioner Repair-Parts

Manual, Manual Systems

332457

332562

3A2801

PD2K Proportioner Installation

Manual, Manual Systems

PD2K Proportioner Operation

Manual, Manual Systems

Mix Manifold Instructions-Parts

Manual

332709

332458

332564

PD2K Proportioner Repair-Parts

Manual, Automatic Systems

PD2K Proportioner Installation

Manual, Automatic Systems

PD2K Proportioner Operation

Manual, Automatic Systems

Manual No.

Description

3A4186

3A4486

332339

332454

PD2K Proportioner Dual Fluid

Panel Operation Manual, Manual

Systems

PD2K Proportioner Dual Fluid

Panel Operation Manual, Automatic

Systems

Pump Repair-Parts Manual

Color Change Valve Repair-Parts

Manual

332455 Color Change Kits Instructions-

Parts Manual

2 332456D

Models

24R968

24R969

24R970

24R971

25M268

26A048

A

A

A

A

A

A

70 cc Low Pressure Color Pump Kit

70 cc High Pressure Color Pump Kit

35 cc Low Pressure Color or

Catalyst Pump Kit

35 cc High Pressure Color or

Catalyst Pump Kit

35 cc Low Pressure Acid Catalyst

Pump Kit

35 cc High Pressure Acid

Catalyst Pump Kit

300 psi (2.068 MPa, 20.68 bar)

1500 psi (10.34 MPa, 103.4 bar)

300 psi (2.068 MPa, 20.68 bar)

1500 psi (10.34 MPa, 103.4 bar)

300 psi (2.068 MPa, 20.68 bar)

1500 psi (10.34 MPa, 103.4 bar)

Figure 1 . Pump Expansion Kit Identification Label

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual, refer back to these Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable.

332456D 3

4

Warnings

prevent fire and explosion:

• Use equipment only in well ventilated area.

• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop cloths (potential static arc).

• Keep work area free of debris, including solvent, rags and gasoline.

• Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes are present.

• Use only grounded hoses.

• Hold gun firmly to side of grounded pail when triggering into pail. Do not use pail liners unless they are antistatic or conductive.

you identify and correct the problem.

• Keep a working fire extinguisher in the work area.

High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like

• Do not spray without tip guard and trigger guard installed.

• Engage trigger lock when not spraying.

• Do not point gun at anyone or at any part of the body.

• Do not put your hand over the spray tip.

• Do not stop or deflect leaks with your hand, body, glove, or rag.

checking, or servicing equipment.

• Tighten all fluid connections before operating the equipment.

• Check hoses and couplings daily. Replace worn or damaged parts immediately.

Moving parts can pinch, cut or amputate fingers and other body parts.

• Keep clear of moving parts.

• Do not operate equipment with protective guards or covers removed.

• Pressurized equipment can start without warning. Before checking, moving, or servicing equipment,

Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swallowed.

• Read MSDSs to know the specific hazards of the fluids you are using.

• Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.

• Always wear chemically impermeable gloves when spraying, dispensing, or cleaning equipment.

332456D

332456D

Warnings

Wear appropriate protective equipment when in the work area to help prevent serious injury, including eye injury, hearing loss, inhalation of toxic fumes, and burns. This protective equipment includes but is not limited to:

• Protective eyewear, and hearing protection.

• Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufacturer.

Misuse can cause death or serious injury.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.

• Do not exceed the maximum working pressure or temperature rating of the lowest rated system equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information about your material, request MSDS from distributor or retailer.

• Do not leave the work area while equipment is energized or under pressure.

• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufacturer’s replacement parts only.

• Do not alter or modify equipment. Alterations or modifications may void agency approvals and create safety hazards.

• Make sure all equipment is rated and approved for the environment in which you are using it.

• Use equipment only for its intended purpose. Call your distributor for information.

• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

• Do not kink or over bend hoses or use hoses to pull equipment.

• Keep children and animals away from work area.

• Comply with all applicable safety regulations.

5

Important Isocyanate (ISO) Information

Isocyanates (ISO) are catalysts used in two component materials.

Spraying or dispensing fluids that contain isocyanates creates potentially harmful mists, vapors, and atomized particulates

• Read and understand the fluid manufacturer’s warnings and Safety Data Sheet (SDS) to know specific hazards and precautions related to isocyanates.

• Use of isocyanates involves potentially hazardous procedures. Do not spray with the equipment unless you are trained, qualified, and have read and understood the information in this manuals and in the fluid manufacturer’s application instructions and SDS.

• Use of incorrectly maintained or mis-adjusted equipment may result in improperly cured material. Equipment must be carefully maintained and adjusted according to instructions in the manual.

• To prevent inhalation of isocynate mists, vapors, and atomized particulates, everyone in the work area must wear appropriate respiratory protection. Always wear a properly fitting respirator, which may include a supplied-air respirator. Ventilate the work area according to instructions in the fluid manufacturer’s SDS.

• Avoid all skin contact with iscocyanates.

Everyone in the work area must wear chemically impermeable gloves, protective clothing and foot coverings as recommended by the fluid manufacturer and local regulatory authority.

Follow all fluid manufacturer recommendations, including those regarding handling of contaminated clothing. After spraying, wash hands and face before eating or drinking.

Cross-contamination can result in cured material in fluid lines which could cause serious injury or damage equipment. To prevent cross-contamination:

B wetted parts.

• Never use solvent on one side if it has been contaminated from the other side.

Exposure to moisture (such as humidity) will cause

ISO to partially cure; forming small, hard, abrasive crystals, which become suspended in the fluid.

Eventually a film will form on the surface and the ISO will begin to gel, increasing in viscosity.

Partially cured ISO will reduce performance and the life of all wetted parts.

• Always use a sealed container with a desiccant dryer in the vent, or a nitrogen atmosphere.

• Keep the ISO pump wet cup or reservoir (if installed) filled with appropriate lubricant. The lubricant creates a barrier between the ISO and the atmosphere.

• Use only moisture-proof hoses compatible with

ISO.

• Never use reclaimed solvents, which may contain moisture. Always keep solvent containers closed when not in use.

• Always lubricate threaded parts with an appropriate lubricant when reassembling.

crystallization varies depending on the blend of ISO, the humidity, and the temperature.

6

Some materials may become self-igniting if applied too thick. Read material manufacturer’s warnings and material MSDS.

332456D

Changing the material types used in your equipment requires special attention to avoid equipment damage and downtime.

• When changing materials, flush the equipment multiple times to ensure it is thoroughly clean.

• Always clean the fluid inlet strainers after flushing.

• Check with your material manufacturer for chemical compatibility.

• When changing between epoxies and urethanes or polyureas, disassemble and clean all fluid components and change hoses. Epoxies often have amines on the B (hardener) side. Polyureas often have amines on the A (resin) side.

Important Isocyanate (ISO) Information

332456D 7

Important Acid Catalyst Information

Pump Expansion Kit 26A048 is designed for acid catalysts (“acid”) currently used in two-component, wood-finishing materials. Current acids in use (with pH levels as low as 1) are more corrosive than earlier acids. More corrosion-resistant wetted materials of construction are required, and must be used without substitution, to withstand the increased corrosive properties of these acids.

Acid is flammable, and spraying or dispensing acid creates potentially harmful mists, vapors, and atomized particulates. To help prevent fire and explosion and serious injury:

• Read and understand the acid manufacturer’s warnings and Safety Data Sheet (SDS) to know specific hazards and precautions related to the acid.

• Use only genuine, manufacturer’s recommended acid-compatible parts in the catalyst system (hoses, fittings, etc). A reaction may occur between any substituted parts and the acid.

• To prevent inhalation of acid mists, vapors, and atomized particulates, everyone in the work area must wear appropriate respiratory protection. Always wear a properly fitting respirator, which may include a supplied-air respirator. Ventilate the work area according to instructions in the acid manufacturer’s SDS.

• Avoid all skin contact with acid. Everyone in the work area must wear chemically impermeable gloves, protective clothing, foot coverings, aprons, and face shields as recommended by the acid manufacturer and local regulatory authority. Follow all acid manufacturer recommendations, including those regarding handling of contaminated clothing. Wash hands and face before eating or drinking.

• Regularly inspect equipment for potential leaks and remove spills promptly and completely to avoid direct contact or inhalation of the acid and its vapors.

• Keep acid away from heat, sparks, and open flames. Do not smoke in the work area. Eliminate all ignition sources.

• Store acid in the original container in a cool, dry, and well-ventilated area away from direct sunlight and away from other chemicals in accordance with acid manufacturer’s recommendations. To avoid corrosion of containers, do not store acid in substitute containers. Reseal the original container to prevent vapors from contaminating the storage space and surrounding facility.

Acid catalysts can be sensitive to atmospheric moisture and other contaminants. It is recommended the catalyst pump and valve seal areas exposed to atmosphere are flooded with ISO oil, TSL, or other compatible material to prevent acid build-up and premature seal damage and failure.

Acid build-up will damage the valve seals and reduce the performance and life of the catalyst pump. To prevent exposing acid to moisture:

• Always use a sealed container with a desiccant dryer in the vent, or a nitrogen atmosphere.

Never store acids in an open container.

• Keep the catalyst pump and the valve seals filled with the appropriate lubricant. The lubricant creates a barrier between the acid and the atmosphere.

• Use only moisture-proof hoses compatible with acids.

• Always lubricate threaded parts with an appropriate lubricant when reassembling.

8 332456D

Installation

• Servicing the electrical control box exposes you to high voltage. To avoid electric shock, turn off power at the main circuit breaker before opening the enclosure.

• All electrical wiring must be done by a qualified electrician and comply with all local codes and regulations.

• Do not substitute or modify system components as this may impair intrinsic safety.

Follow the Pressure Relief Procedure in your PD2K manual whenever you see this symbol.

1.

Flush the system as explained in your PD2K

Operation Manual. Follow the Pressure Relief

Procedure in your PD2K manual.

2.

Close the main air shutoff valve on the air supply line.

3.

Remove electrical power from the system.

directly on the PD2K stand, or mounted onto a wall.

Install using the steps in

Install the Frame, page 10

or the steps in

Install the Wall Bracket, page 11

.

This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from pressurized fluid such as skin injection, splashing fluid, and moving parts, follow the when you stop spraying and before cleaning, checking, or servicing the equipment.

332456D 9

Installation

Use these steps if you want to install the kit onto the

PD2K stand using frame (13).

1.

Follow the steps in

Before Installing the Kit, page 9 .

2.

Install the frame (13) to the upright of the PD2K stand (A) using three screws (16) and nuts (18).

3.

Install the back panel/bracket assembly (B) in the outermost position on the frame (13), to allow clearance for the color change manifold (C).

Fasten the panel to the frame (13) using four screws (15) and nuts (18). Install the top screws from the front and the bottom screws from the back.

expansion kit being installed on the left (color) side of the PD2K proportioner. The pump control module and dual grommet (11) are preassembled at the factory so the cable (8) is facing to the right, allowing easier access to connections inside the PD2K electrical control box (D).

Install a catalyst (35cc) pump expansion kit on the right side of the proportioner, with the pump control module and dual grommet (11) preassembled in the opposite direction so the cable (8) is facing to the left.

Figure 2 Install the Frame and Pump

10 332456D

Use these steps if you want to install the kit away from the PD2K or PD1K stand using wall bracket (47).

1.

Follow the steps in

Before Installing the Kit, page 9 .

2.

Install wall bracket (47) to a wall or other suitable vertical surface using four screws or bolts (user provided).

Installation

3.

Install the back panel/bracket assembly (B) to wall bracket (47) using six screws (15) and six nuts (18).

pump expansion kit being installed on the left

(color) side of the PD1K proportioner. The pump control module and dual grommet (11) are preassembled at the factory so the cable (8) is facing to the right, allowing easier access to connections inside the PD1K electrical control box (D).

Install a catalyst (35cc) pump expansion kit on the right side of the proportioner, with the pump control module and dual grommet (11) preassembled in the opposite direction so the cable (8) is facing to the left.

Figure 3 Install the Wall Bracket and Pump

332456D 11

Installation

The cup is used for either Throat Seal Liquid (TSL) or ISO oil. These liquids prevent exposure of air or moisture with the resin or catalyst at the pump throat packings and dosing valves. The PD2K Proportioner includes two TSL Cup Kits, one for each pump. The cups supply TSL to the upper throat cartridge of the color (70 cc) pump, to the upper and lower throat cartridges of the catalyst (35 cc) pump, and to the four pump dosing valves. When using isocyanate catalysts, the cup attached to the catalyst side of the

PD2K Proportioner is used to supply ISO oil to the upper and lower throat cartridges of the catalyst (35 cc) pump and the catalyst dosing valves.

For TSL, order Part No. 206995, one quart (0.95

liter). For ISO oil, order Part No. 217374, one pint

(0.48 liter).

1.

Slide the kit mounting bracket onto any side of the pump’s hex nut.

2.

Place the TSL cup (73) into the bracket (73a).

permanent black marker to mark a horizontal line on the front of the cup approximately half way between the top and bottom of the cup. Mark a second horizontal line approximately 1/4 in. (3 mm) above the first line. Shining a strong light towards these lines will provide a shadow that will be visible from inside the TSL cup.

Figure 4 Install TSL Cup Kit three ports (two are plugged). Move a plug (73d) if necessary so the barbed fitting (73b) can be put in the port closest to the TSL cup.

3.

Check that the o-ring is in place on the barbed fitting (73b). Apply low strength thread adhesive and install the fitting in the upper throat cartridge port. Be sure the other two ports are plugged

(73d).

12 332456D

4.

Catalyst (35 throat cartridge.

5.

If you are lubricating the dosing valves, remove the plug (73d) and gasket from the valve port (V) closest to the TSL cup.

facing position. This will allow liquid to flow into the valve while allowing air to rise out of the valve.

Check that the o-ring is in place on the barbed fitting (73b). Apply low strength thread adhesive and install the fitting in the valve port (V).

air port (W).

Installation

6.

Cut the tubing (73c) to length as required.

Connect the TSL cup fittings to the fittings on the pump and valves. TSL is gravity-fed from the cup to the pump and valves; position the fittings and tubing to prevent kinks and enable the TSL to flow freely down to the valve and air to rise up and out of the valve.

7.

Fill the cup to the level of the lower black horizontal line with either TSL or ISO oil, as appropriate for the resin and catalyst materials being used.

color (70 cc) pump, be sure the lower u-cup seal is installed in the lower throat cartridge.

checked daily. Fluid levels should remain static for an extended period of time. Rising or falling fluid levels in a TSL cup can be an indication of a condition which needs immediate attention. Refer to the troubleshooting steps in the repair manual for guidance.

When using polyurethane coatings with isocyanate catalysts in high-humidity environments, use of ISO oil on the catalyst pump TSL cup is recommended instead of TSL. The ISO oil will present a barrier that will prevent catalyst hardening from contact with moisture. When performing the first fill of a cup with

ISO oil, it will be necessary to bleed the air out of the feed line.

the two horizontal lines at, and slightly above, the vertical center of the front of the cup before filling.

To bleed air:

1.

Fill the catalyst pump TSL cup to the lower horizontal line.

2.

Remove one plug (73d) from the upper throat cartridge and allow air in that area to flow until no air is being expelled. Replace the plug.

3.

Repeat step 2 at the lower throat cartridge.

4.

Use absorbent rags to clean up excess ISO oil that escaped from the plug holes.

5.

Replenish the ISO oil level in the TSL cup to the lower horizontal line.

valves, remove the unused barbed fittings (73b) from the bottom of the TSL cup (73). Apply low strength thread adhesive and install the plugs and gaskets supplied with the kit.

332456D 13

Installation

For PD2K installations: Follow the steps below.

For PD1K installations: For the first expansion kit, connect the air supply tube (35) directly to the electrical control box (Z). For the second through fourth expansion kits, follow steps 2–4 below.

polyethylene tubing (35) is supplied with the kit to supply air to the expansion pump’s solenoid manifold

(3).

1.

See the PD2K Repair-Parts Manual. Remove the

PD2K fluid panel cover to expose the air supply tubing to the two existing solenoid manifolds.

2.

Cut the air supply tubing upstream of the Y-fitting.

3.

Install the Y-fitting (36) supplied in the kit as shown, to restore the air supply to the two existing solenoid manifolds.

4.

Connect the supplied 1/4 in. (6 mm) OD tubing

(35) between the open branch of the Y-fitting

(36) and the air inlet of the solenoid manifold (3).

This supplies air to the expansion pump solenoid manifold, as shown in the detail of the illustration.

a second splice in the main solenoid air supply line and plumb as explained above.

Figure 5 Air Connection for PD1K First Expansion Kit

Figure 6 Supplying Air to the Expansion Pump

Solenoid Manifold

14 332456D

1.

Connect a 1/4 npt(f) fluid hose from the fluid source to the pump’s fluid inlet fitting (S).

2.

Connect a 1/4 npt(f) fluid outlet hose from the pump’s fluid outlet fitting (R) to the gun’s fluid supply.

Installation

Figure 7 Pump Fluid Connections

332456D 15

Installation

To avoid electrical component damage, remove all system power before plugging any connectors.

NOTE:

Electrical Schematics, page 24 .

1.

Verify that electrical power is removed from the system.

2.

Remove the cover from the PD2K/PD1K electrical control box.

3.

Remove the knockout (K) from the side of the electrical control box.

4.

Thread the cable into the electrical control box and connect to the appropriate connection port on the enhanced fluid control module. For example, connect Pump 1 to P1 and Pump 2 to

P2 (PD1K only); Pump 3 to P3, Pump 4 to P4, and so on.

Figure 8 Install Grommet in Electrical Control

Box

Figure 9 Enhanced Fluid Control Module

Connection Points

16 332456D

Be sure to keep 48 volt cables isolated from the low voltage wiring. All 48 VDC wiring must use the right-hand wireway (X) inside the electrical control box. Use grommet (Y) marked in Figure

9 to install the Pump Expansion Kit wiring.

Installation

5.

The PD2K/PD1K fluid panel cover was previously removed in

Air Connections, page 14 . Thread

the 2–wire cable (22) through the grommet (42) on the bottom of the fluid panel and up into the electrical box through an existing grommet and the wireway. Connect the cable (22) to the appropriate terminals on the top of the 48 VDC power supply: P1 for Pump 1 and P2 for Pump

2 (PD1K only); P3 for Pump 3, P4 for Pump 4.

Connect the red wire to + terminal, black wire to

- terminal.

Figure 10 48 VDC Grommet and Wireway

Figure 11 48 VDC Power Supply Connection

Points

6.

Install the dual grommet (11, shipped loose) on the free end of the D-SUB cable (8).

7.

Fasten the grommet (11) to the side of the electrical control box, using two screws (31).

8.

Reinstall the covers on the PD2K electrical control box and on the fluid panel.

332456D 17

Installation

This equipment must be grounded to reduce the risk of static sparking and electric shock. Electric or static sparking can cause fumes to ignite or explode. Improper grounding can cause electric shock. Grounding provides an escape wire for the electric current.

1.

Verify that the PD2K base unit is properly grounded. See the PD2K installation manual for complete grounding instructions.

2.

Ground the expansion kit pump(s) as follows: a.

If grounded by taking a resistance reading from the ground screw (7) on the added pump kit’s back panel (2) to the system’s true earth ground. Resistance must be less than 1 ohm.

b.

If the the ground screw (7) on the added pump kit’s back panel (2). Connect the other end of the that the main PD2K unit is connected to.

Verify that the added pump is grounded by taking a resistance reading from the ground screw (7) on the added pump kit’s back panel (2) to the system’s true earth ground.

Resistance must be less than 1 ohm.

Figure 12 Grounding the Pump Expansion Kit

18 332456D

1.

Install the cover (12) on the expansion kit, using the screw (37) and nut (18).

Installation

4.

Press and navigate to System Screen 1 on the Advanced Display Module. Change the number of Color Pumps and Catalyst Pumps as needed, based on the kit installation.

Figure 13 Install Expansion Kit Cover (Frame)

Figure 15 System Screen 1

Figure 14 Install Expansion Kit Cover (Wall

Mount)

2.

Restore electrical power to the PD2K/PD1K.

3.

Turn on the control box power switch.

332456D 19

Installation

5.

Go to the Pump Screens. The menu bar at the top of the screen will now show separate tabs for the added pump(s) 3 and 4. Each pump has three screens. Enter the required information, as explained in the PD2K Operation Manual.

Pump Size on Pump Screen 1 and transducer calibration data “Outlet Offset Factor” and “Outlet

Sensitivity Factor” on Pump Screen 2 (see your

PD2K Operation Manual). Also, create a recipe using the new material number, which can be found on Pump Screen 1 under Available Colors

(or Catalysts).

6.

The Home Screen will now show animations and information for the added pumps.

Figure 18 PD2K Home Screen (Advanced

Display Module)

7.

See the PD2K Operation Manual to return the system to service.

Figure 16 Third (Color) Pump Screen

Figure 17 Fourth (Catalyst) Pump Screen

20 332456D

Repair

manifold to the pump’s dosing valves. See the Pump

Tubing Schematic on the next page. Tubing lengths must be 18 in. ± 1/2 in. (457 mm ± 13 mm) for all connections. Always use equal lengths of tubing, to balance the timing of the valves. Lengths longer than

18 in. (457 mm) will increase valve response time.

1.

On the bottom of the solenoid manifold are four ports with tube fittings: UP OPEN, UP CLOSED,

DOWN OPEN, and DOWN CLOSED. These ports provide air to open and close the pump’s inlet dosing valves.

2.

On the side of the solenoid manifold are four ports with 90° tube fittings (not shown): UP

OPEN, UP CLOSED, DOWN OPEN, and DOWN

CLOSED. These ports provide air to open and close the pump’s outlet dosing valves.

Figure 21 Tubing Connections at Solenoid

Manifold, to Pump Outlet Manifold a.

Connect blue tubing (B) from the UP OPEN fitting to the 90° tube fitting on the side of the

OUTLET UP dosing valve.

b.

Connect red tubing (R) from the UP CLOSED fitting to the 90° tube fitting on the end of the

OUTLET UP dosing valve.

Figure 19 Tubing Connections at Solenoid

Manifold, to Pump Inlet Manifold a.

Connect green tubing (G) from the UP OPEN fitting to the 90° tube fitting on the side of the

INLET UP dosing valve.

b.

Connect red tubing (R) from the UP CLOSED fitting to the 90° tube fitting on the end of the

INLET UP dosing valve.

c.

Connect black tubing (K) from the DOWN

OPEN fitting to the 90° tube fitting on the side of the INLET DOWN dosing valve.

d.

Connect red tubing (R) from the DOWN

CLOSED fitting to the 90° tube fitting on the end of the INLET DOWN dosing valve.

Figure 22 Outlet Manifold Tubing

Connections

Figure 20 Inlet Manifold Tubing Connections

332456D 21

Repair

c.

Connect yellow tubing (Y) from the DOWN

OPEN fitting to the 90° tube fitting on the side of the OUTLET DOWN dosing valve.

d.

Connect red tubing (R) from the DOWN

CLOSED fitting to the 90° tube fitting on the end of the OUTLET DOWN dosing valve.

3.

Repeat these steps for each pump in your system.

UP

EXH

See the following table to understand the relationship between pump stroke and dose valve actuation.

Up

Down

Open

Closed

Closed

Open

Open

Closed

Closed

Open

Gre e n (G)

Re d (R)

Blue (B)

Re d (R)

CLOS ED

OP EN

INLET UP

OP EN

OUTLET UP

CLOS ED

DOWN EXH

Bla ck (K)

Re d (R)

Ye llow (Y)

Re d (R)

CLOS ED

OP EN

INLET DOWN

OP EN

OUTLET DOWN

CLOS ED

Figure 23 Pump Tubing Schematic

22 332456D

Repair

If the pump control module needs replacement, install a new module as follows.

To avoid electrical component damage, remove all system power before plugging any connectors.

NOTE:

Electrical Schematics, page 24 .

1.

Connect the motor cable connectors (25) to connection ports 2 and 3 on the pump control module (5) and to the pump motor (N).

for the motor control and the other for encoder feedback. The connectors are keyed differently to ensure correct installation. Attach the two ground wires to the ground screw on the pump motor (N).

Figure 25 Pump Control Module Connections

2.

Connect the 2–wire cable (22) to connection port

8 on the pump control module (5); red wire to pin

1 and black wire to pin 2.

3.

Ensure that the pre-installed D-SUB Cable (8) is securely attached to connection port 1 on the pump control module (5).

4.

Connect the pump’s outlet pressure transducer

(T) to port 5.

5.

Connect the inlet pressure transducer to port 4.

6.

Install the valve wiring (V) in port 7. See

Electrical Schematics, page 24 .

Figure 24 Pump Control Module Connection

Points

332456D 23

Electrical Schematics

FAN

(24P658)

(16P036, 16P037)

WIRE HARNESS

(24P684, 24P685)

PUMP INLET

TRANSDUCER

(16P289, 16P290)

PUMP OUTLET

TRANSDUCER

(16P289, 16P290)

PUMP V/P FOR

FLUID REG.

UP

DOWN

FLOW SENSOR

(120278)

OR G3000 METER

(239716, 258718

16M510, 16M519) wiring expansions in a ProMix PD2K system; models

MC1000, MC2000, and MC4000. Some components shown are not included with all systems.

NOTE: Optional Cables and Modules for a list of cable options.

2 POSITION

SWITCH

(16U725)

CABLE

16T658

LINE FILTER

(16V446)

CABLE

16H078

TERMINAL BLOCK

(114095)

24V

POWER

SUPPLY

(16T660)

POWER IN

RELAY

POWER MODULE

(24R257)

48V-10A POWER SUPPLY

(16U820)

065161, 065159

TION

GATEWAY

5

AWI

GATEWAY

(24R910)

5

16T072

CAN

IS BOARD

(24M485)

FAN

(24P658)

(16P036, 16P037)

WIRE HARNESS

(24P684, 24P685)

PUMP INLET

TRANSDUCER

(16P289, 16P290)

PUMP OUTLET

TRANSDUCER

(16P289, 16P290)

PUMP V/P FOR

FLUID REG.

UP

DOWN

FLOW SENSOR

(120278)

OR G3000 METER

(239716, 258718

16M510, 16M519)

SPLITTER

(16P243)

BARRIER

BOARD

(248192)

4

CABLE (16T659)

CABLE (16T659)

CABLE (16T659)

CABLE (16T659)

FAN

(24P658)

(16P036, 16P037)

WIRE HARNESS

(24P684, 24P685)

PUMP INLET

TRANSDUCER

(16P289, 16P290)

PUMP OUTLET

TRANSDUCER

(16P289, 16P290)

PUMP V/P FOR

FLUID REG.

FAN

(24P658)

(16P036, 16P037)

WIRE HARNESS

(24P684, 24P685)

PUMP INLET

TRANSDUCER

(16P289, 16P290)

PUMP OUTLET

TRANSDUCER

(16P289, 16P290)

PUMP V/P FOR

FLUID REG.

UP

DOWN

UP

DOWN

FLOW SENSOR

(120278)

OR G3000 METER

(239716, 258718

16M510, 16M519)

FLOW SENSOR

(120278)

OR G3000 METER

(239716, 258718

16M510, 16M519)

Figure 26 Electrical Schematic, Sheet 1

2 CABLE

(15V206)

2

CABLE

(15V206)

2

CABLE

(15V206)

GCA

MODULE

EFCM

(24N913)

2

CABLE

(15V206)

2

GUN TRIGGER INPUTS

119159

119159

119159

119159

CABLE

(15V206)

SOLENOID (121324)

PRESSURE SW (121323)

GFB

SWITCH (120278)

SWITCH (120278)

SOLVENT METER (258718)

SOLVENT

FLOW

INPUTS

3

CABLE

(121003)

ADVANCED

DISPLAY MODULE

(24E451)

LIGHT

TOWER

(15X472)

1

CABLE (16V429)

(24R219)

7

(24R219)

7

NON-HAZARDOUS LOCATION

24 332456D

Electrical Schematics

SPLITTER

(16P243)

5 4 3 2 1

UNUSED

1

2

3

3

CABLE (121227)

1 2 3 4 5

2

4

1 2 3 4 5

16T072

1 2 3 4 5

CAN IS BOARD

(NON IS)

(IS)

(24M485)

3

1 2 3 4 5

1

1 2 3

BARRIER

BOARD

(248192)

3

4

5

1

2

P3 P4

AWI

GATEWAY

(24R910)

3

4

1

2

5

5

CABLE

(121227)

3

SOLVENT CUTOFF (121324)

PWR (RED)

SIG (WHITE)

COM (BLACK)

SHIELD/GRN

SOLVENT

METER

(258718)

UNUSED

UNUSED

3

4

5

1

2

P3 P4 3

4

1

2

5

UNUSED

CABLE

(121001)

3

GATEWAY

GFB INTERFACE

(121324)

5

+24VDC

COM

UNUSED

UNUSED

+24VDC

COM

+24VDC

COM

UNUSED

3

2

5

4

1

3

4

1

2

5

10

8

GCA MODULE

EFCM

(24N913)

7

8

5

6

3

4

1

2

9

10

11

12

5

1

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

2

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

GROUND BAR

4

25 PIN D-SUB CABLE

(16T659)

24V

POWER

SUPPLY

(16T660)

N03 N03

2 POSITION

H

(16U725)

N04 N04

CABLE

(16T658)

L N

LINE

FILTER

(16V446)

L GRND N

CABLE

(16H078)

L N GRND

TERMINAL

BLOCK

(114095)

L N GRND

GRND (GRN/YEL)

13 A1(+) A2(-)

RELAY

14

N L GRND

48V-10A

POWER SUPPLY

(16U820)

+ -

+ - + - + - + -

+ - + - + - + -

2

1 2 3 4 5

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

1

3

1 2 3 4

4

1 2 3 4 5

5

1 2 3 4 5

6

1 2 3 4 1 2 3 4

7

5 6 7 8

8

1 2 3 4

2

1 2 3 4 5

3

1 2 3 4

4

1 2 3 4 5

5

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

1

1 2 3 4 5

6

1 2 3 4 1 2 3 4

7

5 6 7 8

8

1 2 3 4

DETAIL A, LOW PRESSURE PUMPS

(24M706, 24M714, 24T799)

2

BREAKOUT MODULE

(24N527)

3

1 2 3 4 5 1 2 3 4

DRAIN/FOIL

(24P684)

AND

PUMP 1

G3000

METER

PUMP 1

(EITHER, 239716,

258718,16M510,

OR 16M519)

GRND

SCREW

DETAIL B, HIGH PRESSURE PUMPS

2

BREAKOUT MODULE

(24N527)

1 2 3 4 5

3

1 2 3 4

(24P685)

DRAIN/FOIL

AND

PUMP 2

MANIFOLD

G3000

METER

PUMP 2

(EITHER, 239716,

258718,16M510,

OR 16M519)

GRND

SCREW

MOTOR

GROUND

SCREW

MOTOR

MOUNTING

SCREW

1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 6 7 8 9

PUMP ENCODER AND MOTOR

(16P037)

10

MOTOR

MOUNTING

SCREW

1 2

Figure 27 Electrical Schematic, Sheet 2, Part 1

1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 6 7 8 9

PUMP ENCODER AND MOTOR

(16P036)

CONTINUED ON THE NEXT PAGE

10

332456D 25

Electrical Schematics

3

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

6

7

8

5

6

3

4

1

2

9

10

11

12

GUN TRIGGER INPUTS

SIG

COM

SIG

COM

SIG

COM

SIG

COM

SIG

COM

SIG

COM

GFB PRESSURE SWITCH (121323)

SOLVENT FLOW SWITCH 1 (120278)

GCA MODULE

EFCM

(24N913)

9

4

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

7

7

8

5

6

3

4

1

2

9

10

11

12

3

4

1

2

5

FLOW RATE ANALOG IN 1

FLOW RATE ANALOG COMMON 1

FLOW RATE ANALOG IN 2

FLOW RATE ANALOG COMMON 2

FLOW RATE ANALOG IN 3

FLOW RATE ANALOG COMMON 3

FLOW RATE ANALOG IN 4

FLOW RATE ANALOG COMMON 4

SIG

COM

SIG

COM

SOLVENT FLOW SWITCH 2 (120278)

SAFETY INTERLOCK SWITCH

CABLE

(121003)

3

3

4

1

2

5

ADVANCED

DISPLAY MODULE

(24E451)

3

4

1

2

5

LIGHT

TOWER

(15X472)

4

25 PIN D-SUB CABLE

(16T659)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

1

BREAKOUT MODULE PUMP 3 (24N527)

2

1 2 3 4 5

3

1 2 3 4

4

1 2 3 4 5

5

1 2 3 4 5

6

1 2 3 4 1 2 3 4

7

5 6 7 8

8

1 2 3 4

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

1

BREAKOUT MODULE PUMP 4 (24N527)

2

1 2 3 4 5

3

1 2 3 4

4

1 2 3 4 5

5

1 2 3 4 5

6

1 2 3 4 1 2 3 4

7

5 6 7 8

8

1 2 3 4

ENCODER/MOTOR

AND

WIRE HARNESS

PUMP 3

SEE DETAIL A OR B

MANIFOLD

G3000

METER

PUMP 3

(EITH ER, 239716,

258718,16M510,

OR 16M519)

GRND

SCREW

TWISTED PAIR CABLE (16W159)

Figure 28 Electrical Schematic, Sheet 2, Part 2

CONTINUED ON THE NEXT PAGE

ENCODER/MOTOR

AND

WIRE HARNESS

PUMP 4

SEE DETAIL A OR B

TWISTED PAIR CABLE (16W159)

MANIFOLD

G3000

METER

PUMP 4

ER, 239716,

258718,16M510,

OR 16M519)

GRND

SCREW

26 332456D

Electrical Schematics

FROM CAN IS BOARD (24M485)

2

FLUSH

MANIFOLD

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

4

5

6

1

2

3

J8

1 2 3 4 5

COLOR

CHANGE

MODULE 1

(COLORS

1 THRU 8)

J9

6

3

4

5

1

2

6

J15 J16 4

3

2

6

5

1

4

3

2

6

5

1

4

5

6

1

2

3

J14 J10

6

5

4

3

2

1

1 2 3 4 5

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

MANIFOLD

DUMP

*FLUSH

MANIFOLD

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

1 2 3 4 5

1

2

3

4

5

6

J8

COLOR

CHANGE

MODULE 2

(COLORS

9 THRU 16)

J9

6

3

4

5

1

2

6

J15 J16 4

3

2

6

5

1

4

3

2

6

5

1

4

5

6

1

2

3

J14 J10

6

5

4

3

2

1

1 2 3 4 5

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

MANIFOLD

DUMP* FLUSH

CATALYST 1

CATALYST 2

CATALYST 3

CATALYST 4

MANIFOLD

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

1

2

3

4

5

6

CATALYST

CHANGE

MODULE 5

(CATALYST

1 THRU 4)

J8

6

J9

4

3

2

6

5

1

3

4

5

1

2

6

J15 J16 4

3

2

6

5

1

4

5

6

1

2

3

J14 J10

6

5

4

3

2

1

1 2 3 4 5

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

MANIFOLD

DUMP

CATALYST 1

CATALYST 2

CATALYST 3

CATALYST 4

*FLUSH

MANIFOLD

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

1 2 3 4 5

COLOR

CHANGE

MODULE 3

(COLORS

17 THRU 24)

1

2

3

4

5

6

J8

3

4

5

1

2

6

J15

6

J9

J16

2

1

4

3

6

5

4

3

2

6

5

1

4

5

6

1

2

3

J14 J10

6

5

4

3

2

1

5 4 3 2 1

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

MANIFOLD

DUMP*

2

Figure 29 Electrical Schematic, Sheet 3

* May be unused in some configurations.

CONTINUED ON THE NEXT PAGE

*FLUSH

MANIFOLD

+24VDC

COM

+24VDC

COM

+12VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

UNUSED

UNUSED

UNUSED

UNUSED

1 2 3 4 5

1

2

3

4

5

6

COLOR

CHANGE

MODULE 4

(COLORS

25 THRU 32)

J8 J9

4

3

2

6

5

1

6

3

4

5

1

2

6

J15 J16

2

1

4

3

6

5

4

5

6

1

2

3

J14 J10

6

5

4

3

2

1

1 2 3 4 5

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

UNUSED

UNUSED

UNUSED

UNUSED

MANIFOLD

DUMP*

332456D 27

Electrical Schematics

FLUSH

CATALYST 3

CATALYST 4

MANIFOLD

+24VDC

COM

+24VDC

COM

+24VDC

COM

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

3

4

1

2

5

6

J8

CATALYST

CHANGE

MODULE 6

(CATALYST

3 THRU 4)

J9

6

3

4

1

2

5

6

J15 J16 4

3

6

5

2

1

4

3

6

5

2

1

3

4

1

2

5

6

J14

1 2 3 4 5

J10

4

3

6

5

2

1

COM

+24VDC

COM

+24VDC

COM

+24VDC

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

MANIFOLD

DUMP

CATALYST 3

CATALYST 4

FLUSH

CATALYST 1

CATALYST 2

MANIFOLD

+24VDC

COM

+24VDC

COM

+24VDC

COM

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

5 4 3 2 1

3

4

1

2

5

6

3

4

1

2

5

6

CATALYST

CHANGE

MODULE 5

(CATALYST

1 THRU 2)

J8

6

J9

4

3

6

5

2

1

J15 J16 4

3

6

5

2

1

3

4

1

2

5

6

J14

1 2 3 4 5

J10

4

3

6

5

2

1

COM

+24VDC

COM

+24VDC

COM

+24VDC

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

MANIFOLD

DUMP

CATALYST 1

CATALYST 2

1 2 3 4 5

COLOR

CHANGE

MODULE 4

(COLORS

ALTERNATE CONFIGURATION

FOR CATALYST CHANGE CONTROL

Figure 30 Electrical Schematic, Sheet 3, Alternate

Configuration for Catalyst Change Control

CONTINUED ON THE NEXT PAGE

28 332456D

FROM CAN IS BOARD (24M485)

NON-HAZARDOUS LOCATION

HAZARDOUS LOCATION

COLOR FLUSH

COLOR 1

COLOR 2

COLOR 3

COLOR 4

COLOR 5

COLOR 6

COLOR 7

COLOR 8

MANIFOLD

+12VDC

COM

+12VDC

COM

+12VDC

COM

+12VDC

COM

+12VDC

COM

+12VDC

COM

+12VDC

COM

+12VDC

COM

+12VDC

COM

1 2 3 4 5

COLOR

3

4

1

2

5

6

3

4

1

2

5

6

MODULE 7

(COLORS

33 THRU 40)

J8 J9

4

3

6

5

2

1

7

J15 J16

4

3

6

5

2

1

3

4

1

2

5

6

J14 J10

4

3

6

5

2

1

1 2 3 4 5

COM

+12VDC

COM

+12VDC

COM

+12VDC

COM

+12VDC

COM

+12VDC

COM

+12VDC

COM

+12VDC

COM

+12VDC

COM

+12VDC

MANIFOLD

CATALYST FLUSH

CATALYST 1

CATALYST 2

CATALYST 3

CATALYST 4

COLOR 9

COLOR 10

COLOR 11

COLOR 12

COLOR 13

COLOR 14

COLOR 15

COLOR 16

COLOR 17

COLOR 18

COLOR 19

COLOR 20

COLOR 21

MANIFOLD

+12VDC

COM

+12VDC

COM

+12VDC

COM

+12VDC

COM

+12VDC

COM

+12VDC

COM

+12VDC

COM

+12VDC

COM

+12VDC

COM

1 2 3 4 5

COLOR

3

4

1

2

5

6

MODULE 8

(COLORS

41 THRU 48)

J8 J9

7

3

4

1

2

5

6

J15 J16 4

3

6

5

2

1

4

3

6

5

2

1

3

4

1

2

5

6

J14

5 4 3 2 1

J10

4

3

6

5

2

1

COM

+12VDC

COM

+12VDC

COM

+12VDC

COM

+12VDC

COM

+12VDC

COM

+12VDC

COM

+12VDC

COM

+12VDC

COM

+12VDC

MANIFOLD

COLOR 22

COLOR 23

COLOR 24

COLOR 25

COLOR 26

COLOR 27

COLOR 28

COLOR 29

COLOR 30

Figure 31 Electrical Schematic, Sheet 3, Hazardous

Location

5 4 3 2 1

BOOTH CONTROL

(24M731)

Electrical Schematics

332456D 29

Electrical Schematics

wiring expansions in a ProMix PD2K system; models

MC1002, MC2002, and MC4002. Some components shown are not included with all systems.

NOTE: Optional Cables and Modules for a list of cable options.

POWER MODULE

(26A189)

2 POSITION

SWITCH

(16U725)

CABLE

16T658

(16V446)

CABLE

16H078

POWER IN

(114095)

24V

POWER

SUPPLY

(16T660)

48V-10A POWER SUPPLY

(16U820)

RELAY 1 RELAY 2

TERMINAL BLOCK WITH FUSES

GATEWAY

5

AWI

GATEWAY

(24R910)

5

16T072

CAN

IS BOARD

(24M485)

17L058 FAN

(24P658)

AND MOT

(16P036, 16P037)

WIRE HARNESS

(24P684, 24P685)

PUMP INLET

TRANSDUCER

(16P289, 16P290)

PUMP OUTLET

TRANSDUCER

(16P289, 16P290)

CABLE 126232

OR 17N315

UP

DOWN

SOLVENT

METER 1

(258718)

FAN

(24P658)

(16P036, 16P037)

WIRE HARNESS

(24P684, 24P685)

PUMP INLET

TRANSDUCER

(16P289, 16P290)

PUMP OUTLET

TRANSDUCER

(16P289, 16P290)

CABLE 126232

OR 17N315

UP

DOWN

SOLVENT

METER 2

(258718)

SPLITTER

(16P243)

BARRIER

BOARD

(248192)

2

CABLE

(15V206)

2 CABLE

(15V206)

2

CABLE

(15V206)

GCA

EFCM

(24N913)

2

CABLE

(15V206)

2

CABLE

(15V206)

CABLE

15V819

AIR FLOW SW. 1 (119159)

AIR FLOW SW. 2 (119159)

GFB PRESS. SW. 1 (121323)

GFB PRESS. SW. 2 (121323)

GFB VALVE 1 (121324)

GFB VALVE 2 (121324)

AIR

CONTROL

MODULE

(26A231)

SOLVENT CUTOFF VALVE (121324)

SOLVENT CUTOFF VALVE (121324)

SWITCH (120278)

SWITCH (120278)

SWITCH (120278)

SWITCH (120278)

SOLVENT

FLOW

INPUTS

SAFETY INTERLOCK SWITCH

CABLE

(121003)

3

(24E451)

TOWER

(15X472)

1

CABLE (16V429)

COLOR CHANGE

MODULE 7

(24R219)

7

1

CABLE

(16V426)

(24M731)

WITH SHUNT

(17M540)

COLOR CHANGE

MODULE 8

(24R219)

7

1

CABLE

(16V426)

BOOTH

CONTROL

(24M731) FAN

(24P658)

(16P036, 16P037)

WIRE HARNESS

(24P684, 24P685)

PUMP INLET

TRANSDUCER

(16P289, 16P290)

PUMP OUTLET

TRANSDUCER

(16P289, 16P290)

PUMP V/P FOR

FLUID REG.

UP

DOWN

FAN

(24P658)

(16P036, 16P037)

WIRE HARNESS

(24P684, 24P685)

PUMP INLET

TRANSDUCER

(16P289, 16P290)

PUMP OUTLET

TRANSDUCER

(16P289, 16P290)

PUMP V/P FOR

FLUID REG.

UP

DOWN

(120278) (120278)

(239716, 258718

16M510, 16M519)

(239716, 258718

16M510, 16M519)

Figure 32 Electrical Schematic, Sheet 1

4

CABLE (16T659)

30 332456D

Electrical Schematics

SPLITTER

(16P243)

5 4 3 2 1

3

4

5

1

2

1

2

3

4

5

16T072

1 2 3 4 5

2

CAN IS BOARD

(NON IS)

1 2 3 4 5

1

4

1 2 3 4 5

(IS)

(24M485)

3

1 2 3 4 5

UNUSED

1

2

3

J4

3

CABLE (121227)

1 2 3

J5

BOARD

(248192)

3

4

1

2

5

P3 P4

AWI

GATEWAY

(24R910)

3

4

1

2

5

5

CABLE

(121227)

3

UNUSED

UNUSED

3

4

1

2

5

P3

GATEWAY

5

P4 3

4

1

2

5

UNUSED

CABLE

(121001)

3

3

2

5

4

1

3

4

1

2

5

10

8

GFB OUTPUT VALVE 1

GFB OUTPUT VALVE 2

+24VDC

COM

+24VDC

COM

GREEN/BLACK +24VDC

ORANGE/BLACK COM

BLUE/BLACK +24VDC

RED/WHITE COM

UNUSED

SIG

COM

UNUSED

7

8

5

6

3

4

1

2

9

10

11

12

5

25 PIN D-SUB

4

1

GCA MODULE

EFCM

(24N913)

2 3 4

24V

POWER

SUPPLY

(16T660)

GROUND

BAR

2

1 2 3 4 5

1

3

1 2 3 4

4

1 2 3 4 5

5

1 2 3 4 5

6

1 2 3 4 1 2 3 4

7

5 6 7 8

8

1 2 3 4

2

1 2 3 4 5

1

3

1 2 3 4

4

1 2 3 4 5

5

1 2 3 4 5

6

1 2 3 4 1 2 3 4

7

5 6 7 8

8

1 2 3 4

N03 N03

2 POSITION

SWITCH

(16U725)

N04 N04

CABLE

(16T658)

L N

LINE

FILTER

(16V446)

L GND N

CABLE

(16H078)

L N GND

NAL

BLOCK

(114095)

L N GND

GRND (GRN/YEL)

N L GRND

48V-10A

POWER SUPPLY

(16U280)

- - + +

15

18

2

A1

A2

15

18

RELA

1

A1

A2

AND

WIRE HARNESS

PUMP 1

BROWN (UNUSED)

DRAIN (UNUSED)

BLUE

BLACK

BROWN (UNUSED)

DRAIN (UNUSED)

BLUE

BLACK

CABLE (126232 OR 17N315)

PUMP 1

SOLVENT

1

(258718)

- + -

4 3 2 1

GND

SCREW

DETAIL A, LOW PRESSURE PUMPS

(24M706, 24M714, 24T799)

2

1 2 3 4 5

(24N527)

WIRE HARNESS

(24P684)

3

1 2 3 4

DRAIN/FOIL

TWISTED PAIR CABLE (16W159)

DETAIL B, HIGH PRESSURE PUMPS

(24M707, 24M715, 24T800)

2

1 2 3 4 5

(24N527)

WIRE HARNESS

(24P685)

3

1 2 3 4

DRAIN/FOIL

AND

WIRE HARNESS

PUMP 2

CABLE (126232 OR 17N315)

TWISTED PAIR CABLE (16W159)

PUMP 2

MANIFOLD

SOLVENT

2

(258718)

GND

SCREW

7

7

8

5

6

3

4

1

2

9

10

11

12

9 3

4

1

2

5

6

7

8

5

6

3

4

1

2

9

10

11

12

MOTOR

GROUND

SCREW

MOTOR

MOUNTING

SCREW

1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 6 7 8 9

PUMP ENCODER AND MOTOR

(16P037)

10

MOTOR

MOUNTING

SCREW

1 2

Figure 33 Electrical Schematic, Sheet 2, Part 1

1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 6 7 8 9

PUMP ENCODER AND MOTOR

(16P036)

CONTINUED ON THE NEXT PAGE

10

332456D 31

Electrical Schematics

5

4

3

2

1

1

2

3

4

5

10

8

7

8

5

6

3

4

1

2

9

10

11

12

5

1

GCA MODULE

EFCM

(24N913)

2 3 4

6

9

10

11

12

6

7

8

1

4

5

2

3

SIG

COM

SIG

COM

SIG

COM

SIG

COM

SIG

COM

SIG

COM

BLACK

WHITE

RED

GREEN

AIR FLOW SWITCH 1

AIR FLOW SWITCH 2

SOLVENT FLOW SW. 1 (120278) LEFT BRKT

SOLVENT FLOW SW. 2 (120278) LEFT BRKT

SOLVENT FLOW SW. 3 (120278) RIGHT BRKT

SOLVENT FLOW SW. 4 (120278) RIGHT BRKT

7

10

11

12

8

9

6

7

3

4

5

1

2

9

1

2

3

4

5

PLC DISCRETE 4-20mA INPUT 1

PLC DISCRETE 4-20mA COMMON 1

PLC DISCRETE 4-20mA INPUT 2

PLC DISCRETE 4-20mA COMMON 2

UNUSED

UNUSED

UNUSED

UNUSED

SIG ORANGE

COM

SIG

COM

BLUE

WHITE/BLACK

RED/BLACK

CABLE

(121003)

3

3

4

1

2

5

ADVANCED

DISPLAY MODULE

(24E451)

GFB INPUT PRESSURE SWITCH 1

GFB INPUT PRESSURE SWITCH 2

1

4

5

2

3

LIGHT

TOWER

(15X472)

CABLE

15V819

AIR CONTROL MODULE (26A231)

WHITE

RED

GREEN

ORANGE

BLUE

WHITE/BLACK

RED/BLACK

GREEN/BLACK

ORANGE/BLACK

BLUE/BLACK

RED/WHITE

TERMINAL

BLOCKS

7

8

9

10

3

4

5

6

1

2

11

12

+ SIG

- COM

+ SIG

- COM

+ SIG

- COM

+ SIG

- COM

+ 24VDC

- COM

+ 24VDC

- COM

RED

RED

AIR FLOW SWITCH 1

119159

AIR FLOW SWITCH 2

119159

GFB INPUT PRESSURE SWITCH 1

121323

GFB INPUT PRESSURE SWITCH 2

121323

GFB OUTPUT VALVE 1

121324

GFB OUTPUT VALVE 2

121324

2

1 2 3 4 5

25 PIN D-SUB

CABLE (16T659)

4

3

1 2 3 4

1

BREAKOUT MODULE PUMP 3 (24N527)

4

1 2 3 4 5

5

1 2 3 4 5

6

1 2 3 4 1 2 3 4

7

5 6 7 8

8

1 2 3 4

2

1 2 3 4 5

3

1 2 3 4

1

BREAKOUT MODULE PUMP 4 (24N527)

4

1 2 3 4 5

5

1 2 3 4 5

6

1 2 3 4 1 2 3 4

7

5 6 7 8

8

1 2 3 4

AND

WIRE HARNESS

PUMP 3

SEE DET

ENCODER/M

AND

WIRE HARNESS

PUMP 4

PUMP 3

MANIFOLD

G3000

METER

PUMP 3

(EITHER, 239716,

258718,16M510,

OR 16M519)

GND

SCREW

PUMP 4

MANIFOLD

G3000

METER

PUMP 4

(EITHER, 239716,

258718,16M510,

OR 16M519)

GND

SCREW

Figure 34 Electrical Schematic, Sheet 2, Part 2

CONTINUED ON THE NEXT PAGE

TWISTED PAIR CABLE (16W159)

TWISTED PAIR CABLE (16W159)

32 332456D

Electrical Schematics

FROM CAN IS BOARD (24M485)

FLUSH

COLOR 1

COLOR 2

COLOR 3

COLOR 4

COLOR 5

COLOR 6

COLOR 7

COLOR 8

2

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

4

5

6

1

2

3

J8

1 2 3 4 5

COLOR

CHANGE

MODULE 1

(COLORS

1 THRU 8)

6

J9

3

4

5

1

2

6

J15 J16 4

3

2

6

5

1

4

3

2

6

5

1

4

5

6

1

2

3

J14 J10

6

5

4

3

2

1

1 2 3 4 5

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COLOR 1

COLOR 2

COLOR 3

COLOR 4

COLOR 5

COLOR 6

COLOR 7

COLOR 8

*FLUSH

COLOR 9

COLOR 10

COLOR 11

COLOR 12

COLOR 13

COLOR 14

COLOR 15

COLOR 16

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

1 2 3 4 5

1

2

3

4

5

6

J8

COLOR

CHANGE

MODULE 2

(COLORS

9 THRU 16)

J9

6

3

4

5

1

2

6

J15 J16

3

2

1

6

5

4

4

3

2

6

5

1

4

5

6

1

2

3

J14 J10

6

5

4

3

2

1

1 2 3 4 5

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COLOR 9

COLOR 10

COLOR 11

COLOR 12

COLOR 13

COLOR 14

COLOR 15

COLOR 16

FLUSH

CATALYST 1

CATALYST 2

CATALYST 3

CATALYST 4

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

3

4

5

1

2

6

1

2

3

4

5

6

CATALYST

CHANGE

MODULE 5

(CATALYST

1 THRU 4)

J8

6

J9

4

3

2

6

5

1

J15 J16

3

2

1

6

5

4

4

5

6

1

2

3

J14 J10

6

5

4

3

2

1

1 2 3 4 5

COM

+24VDC

COM

+24VDC

COM

+12VDC

COM

+24VDC

COM

+24VDC

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

CATALYST 1

CATALYST 2

CATALYST 3

CATALYST 4

*FLUSH

COLOR 17

COLOR 18

COLOR 19

COLOR 20

COLOR 21

COLOR 22

COLOR 23

COLOR 24

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

1 2 3 4 5

COLOR

CHANGE

MODULE 3

(COLORS

17 THRU 24)

1

2

3

4

5

6

J8

3

4

5

1

2

6

J15

6

J9

J16

3

2

1

6

5

4

3

2

1

6

5

4

4

5

6

1

2

3

J14 J10

4

3

2

6

5

1

5 4 3 2 1

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

Figure 35 Electrical Schematic, Sheet 3, Part 1

* May be unused in some configurations.

CONTINUED ON THE NEXT PAGE

2

COLOR 17

COLOR 18

COLOR 19

COLOR 20

COLOR 21

COLOR 22

COLOR 23

COLOR 24

*FLUSH

COLOR 25

COLOR 26

COLOR 27

COLOR 28

COLOR 29

COLOR 30

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

UNUSED

UNUSED

UNUSED

UNUSED

1

2

3

4

5

6

J8

1 2 3 4 5

COLOR

CHANGE

MODULE 4

(COLORS

25 THRU 32)

J9

6

3

4

5

1

2

6

J15 J16

3

2

1

6

5

4

3

2

1

6

5

4

4

5

6

1

2

3

J14 J10

4

3

2

6

5

1

1 2 3 4 5

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

COM

+24VDC

UNUSED

UNUSED

UNUSED

UNUSED

COLOR 25

COLOR 26

COLOR 27

COLOR 28

COLOR 29

COLOR 30

332456D 33

Electrical Schematics

FROM CAN IS BOARD (24M485)

1

CABLE (16V429)

NON-HAZARDOUS LOCATION

HAZARDOUS LOCATION

COLOR FLUSH

COLOR 1

COLOR 2

COLOR 3

COLOR 4

COLOR 5

COLOR 6

COLOR 7

COLOR 8

MANIFOLD

RED

RED

+12VDC

BLACK

RED

BLACK

COM

+12VDC

COM

+12VDC

BLACK COM

RED

BLACK

RED

BLACK

RED

BLACK

+12VDC

COM

+12VDC

COM

+12VDC

COM

RED

BLACK

RED

BLACK

RED

BLACK

+12VDC

COM

+12VDC

COM

+12VDC

COM

3

4

1

2

5

6

3

4

1

2

5

6

1 2 3 4 5

COLOR

CHANGE

MODULE 7

(COLORS

33 THRU 40)

J8 J9

4

3

6

5

2

1

7

J15 J16

4

3

6

5

2

1

3

4

1

2

5

6

J14 J10

4

3

6

5

2

1

5 4 3 2 1

COM

+12VDC

COM

+12VDC

COM

+12VDC

BLACK

RED

BLACK

RED

BLACK

RED

COM

+12VDC

COM

+12VDC

COM

+12VDC

BLACK

RED

BLACK

RED

BLACK

RED

COM

+12VDC

COM

+12VDC

COM

+12VDC

BLACK

RED

BLACK

RED

BLACK

RED

MANIFOLD

CATALYST FLUSH

CATALYST 1

CATALYST 2

CATALYST 3

CATALYST 4

COLOR 9

COLOR 10

COLOR 11

COLOR 12

5 4 3 2 1

BOOTH CONTROL

(24M731)

WITH SHUNT

(17M540)

1 2 3 4 5

J1

COLOR 13

COLOR 14

COLOR 15

COLOR 16

COLOR 17

COLOR 18

COLOR 19

COLOR 20

COLOR 21

MANIFOLD

RED

BLACK

RED

BLACK

RED

BLACK

+12VDC

COM

+12VDC

COM

+12VDC

COM

RED

BLACK

RED

BLACK

RED

BLACK

+12VDC

COM

+12VDC

COM

+12VDC

COM

RED

BLACK

RED

BLACK

RED

BLACK

+12VDC

COM

+12VDC

COM

+12VDC

COM

1 2 3 4 5

COLOR

CHANGE

MODULE 8

(COLORS

41 THRU 48)

3

4

1

2

5

6

J8

3

4

1

2

5

6

J15

7

J9

J16 4

3

6

5

2

1

4

3

6

5

2

1

3

4

1

2

5

6

J14

5

4 3

2

1

J10

4

3

6

5

2

1

COM

+12VDC

COM

+12VDC

COM

+12VDC

BLACK

RED

BLACK

RED

BLACK

RED

COM

+12VDC

COM

+12VDC

COM

+12VDC

BLACK

RED

BLACK

RED

BLACK

RED

COM

+12VDC

COM

+12VDC

COM

+12VDC

BLACK

RED

BLACK

RED

BLACK

RED

MANIFOLD

COLOR 22

COLOR 23

COLOR 24

COLOR 25

COLOR 26

COLOR 27

COLOR 28

COLOR 29

COLOR 30

5 4 3 2 1

BOOTH CONTROL

(24M731)

Figure 36 Electrical Schematic, Sheet 3, Part 2

CONTINUED ON THE NEXT PAGE

34 332456D

FLUSH

CATALYST 3

CATALYST 4

MANIFOLD

+24VDC

COM

+24VDC

COM

+24VDC

COM

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

CATALYST

CHANGE

1

2

3

4

5

6

(CATALYST

3 THRU 4)

J8

6

J9

1

2

3

4

5

6

J15 J16

6

5

4

3

2

1

3

2

1

6

5

4

1

2

3

4

5

6

J14

1 2 3 4 5

J10

6

5

4

3

2

1

COM

+24VD

COM

+24VD

COM

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

MANIFOLD

DUMP

CATALYST 3

CATALYST 4

Electrical Schematics

FLUSH

CATALYST 1

CATALYST 2

MANIFOLD

+24VDC

COM

+24VDC

COM

+24VDC

COM

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

5 4 3 2

CATALYST

CHANGE

1

4

5

6

1

2

3

(CATALYST

1 THRU 2)

J8 J9

6

5

4

3

2

1

6

1

2

3

4

5

6

J15 J16

3

2

1

6

5

4

1

2

3

4

5

6

J14 J10

6

5

4

3

2

1

1 2 3 4 5

COM

C

COM

C

COM

MANIFOLD

DUMP

CATALYST 1

CATALYST 2

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

UNUSED

1 2 3 4 5

COLOR

CHANGE

(COLORS

25 THRU 32)

ALTERNATE CONFIGURATION

FOR CATALYST CHANGE CONTROL

Figure 37 Electrical Schematic, Sheet 4, Alternate

Configuration for Catalyst Change Control

332456D 35

Pump Expansion Kit Parts

36 332456D

Pump Expansion Kit Parts

7

8

9

2

3

4

5

Ref Part

1

— — —

6

— — —

24T772

24T770

24N527

— — —

— — —

16V659

24T790

24T791

24T788

24T789

24T818

24T819

10

— — —

11

— — —

12 16V858

13

— — —

14 C19798

15

— — —

16 — — —

BRACKET, mounting, pump

PANEL, back

1

1

MANIFOLD, solenoid 1

1 KIT, fan

MODULE, control, pump

SCREW, cap, socket head; 10–32 x 1.5 in.

(38 mm)

SCREW, ground; M5 x 0.8

CABLE, D-SUB; 25 pin; 6 ft (1.83 m)

PUMP, 70 cc, A side, low pressure; for Kit

24R968; see manual

332339

PUMP, 70 cc, A side, high pressure; for Kit

24R969; see manual

332339

PUMP, 35 cc, B side, low pressure; for Kit

24R970; see manual

332339

PUMP, 35 cc, B side, high pressure; for Kit

24R971; see manual

332339

PUMP, 35 cc, B side, low pressure; for Kit

25M268; see manual

332339

PUMP, 35 cc, B side, high pressure; for Kit

26A048; see manual

332339

BRACKET, mounting, pump

GROMMET, dual cable

COVER

1

4

1

1

1

1

1

1

1

1

1

2

1

FRAME

SCREW, cap, socket head; 1/4–20 x 3/8 in.

(10 mm)

SCREW, cap, hex head; 3/8–16 x 7/8 in.

(22 mm)

SCREW, cap, hex head; 3/8–16 x 3.75

in. (95 mm)

1

6

7

3

332456D

Ref Part

18

— — —

19 — — —

22

— — —

25 24P684

24P685

27

— — —

30 101550

31 105209

32 114231

33

— — —

34

— — —

35

— — —

36 115287

37

— — —

41 16X048

42

— — —

46

— — —

47

— — —

48

— — —

49

— — —

50

— — —

NUT, lock; 3/8–16 10

PLUG, tube, square 4

CABLE, 2–wire

WIRE HARNESS; for Kits 24R968 and

24R970

WIRE HARNESS; for Kits 24R969,

24R971, and 26A048

TIE WRAP (not shown)

SCREW, cap, socket head; 1/4–20 x 1/2 in.

(13 mm)

SCREW, cap, socket head; 10–32 x 7/8 in.

(22 mm)

NUT, lock; 10–32

1

1

1

3

2

4

4

6 ft

(1.83

m)

TUBE, nylon, red; for control air to turn inlet and outlet valves off;

5/32 in. (4 mm) OD

TUBE, nylon, green; for control air to turn inlet up valve on; 5/32 in. (4 mm) OD

TUBE, polyethylene;

1/4 in. (6 mm) OD x 6 ft (1.83 m)

Y-FITTING; 1/4 in. (6 mm) OD tubing

SCREW, cap, hex head; 3/8–16 x 2.75

in. (70 mm)

LABEL, notice

1.5 ft

(457 mm)

6 ft

(1.83

m)

1

1

2

GROMMET

WASHER; 3/8

BRACKET, wall (use with PD1K)

TUBE, nylon, black; for control air to turn inlet down valve on;

5/32 in. (4 mm) OD

TUBE, nylon, blue; for control air to turn outlet up valve on;

5/32 in. (4 mm) OD

TUBE, nylon, yellow; for control air to turn outlet down valve on;

5/32 in. (4 mm) OD

3

3

1

1.5 ft

(457 mm)

1.5 ft

(457 mm)

1.5 ft

(457 mm)

37

Pump Expansion Kit Parts

Ref Part

73 24T302

73a

73b 24U617

73c

— — —

— — —

KIT, cup, TSL; includes items

73a-73e

BRACKET

KIT, barbed fittings; includes o-rings; package of 12

TUBE, polyurethane;

1/4 in. (6 mm) OD; 10 ft (3.05 m); cut to fit

1

1

1

1

Ref Part

73d

73e

— — —

— — —

PLUG, screw; 10–32; to replace unused item 73b at TSL cup; not shown

GASKET; for item

73d; not shown

4

4

Items marked — — — are not available separately.

38 332456D

Technical Data

Maximum fluid working pressure:

Kits 24R968, 24R970, and 25M268

Kits 24R969, 24R971, and 26A048

Maximum working air pressure:

Wetted parts:

300 psi

1500 psi

100 psi

2.1 MPa, 21 bar

10.5 MPa, 105 bar

0.7 MPa, 7.0 bar

See Pump manual 332339.

332456D 39

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by

Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall

Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS

IMPLIED,

OF

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

GRACO

AND

MATERIALS not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from

Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.

For the latest information about Graco products, visit www.graco.com.

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

For patent information, see www.graco.com/patents.

Original Instructions. This manual contains English. MM 332456 www.graco.com

Revision D, May 2020

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals