Graco 3A5205A, Bead Dispenser Kit, LineLazer 3400, Airlessco 3350, 4350, Pioneer 3500, 3500SP Owner's Manual


Add to my manuals
8 Pages

advertisement

Graco 3A5205A, Bead Dispenser Kit, LineLazer 3400, Airlessco 3350, 4350, Pioneer 3500, 3500SP Owner's Manual | Manualzz

Installation

Kit, Bead Dispenser

LineLazer 3400

Airlessco 3350, 3350

SP

, 4350

Pioneer 3500, 3500

SP

3A5205A

EN

For application of line striping materials. Not approved for use in European explosive atmosphere locations.

Important Safety Instructions

Read all warnings and instructions in this manual and related manuals.

Be familiar with the controls and the proper usage of the equipment.

Save these instructions.

LineLazer 3400

Airlessco 3350, 3350 SP , 4350

Pioneer 3500, 3500 SP

Glass bead system with one 6-in.

(152 mm) dispenser

Glass bead system with 12-in.

(305 mm) dispensers

6-in. (152 mm) dispenser and hose

6-in. (152 mm) wind deflector kit with aluminum dispenser

6-in. (152 mm) wind deflector with plastic dispenser

12-in. (305 mm) dispenser and two hoses

12-in. (305 mm) wind deflector with aluminum dispenser

Model

24Z726

24Z727

277067

277066

245519

245516

245520

Series

A

A

A

A

A

A

A ti31501a

2

Bead Dispenser Kit

Bead Dispenser Kit

Setup

NOTE: Glass bead system and paint guns can be mounted on either side of sprayer.

1. Perform Pressure Relief Procedure (see sprayer manual).

2. Attach bead mounting bracket (20) to frame.

3. Bolt bead hopper frame legs (1, 3) to bracket (20) with four flange head cap screws (9) and lock nuts

(10).

4. Place bead hopper ring (14) into holes in bead hopper legs.

5. Bolt bead hopper and bead hopper ring together with washers (15) and lock nuts (4) from kit bag.

6. Install bead hopper (7) on gun side on top of beads hopper frame.

7. Remove collar from mounting block of dispenser

(8). Locate dispenser on gun support and reconnect collar to attach dispenser to support.

8. Move bead dispenser to desired location on rod.

Loosen screw (4) and position link (3) to connect to gun trigger actuator (C). Tighten screw (4) and attach dispenser connecting rod (B) to gun trigger with bridge pin (2).

9. Position spray gun and bead dispenser assembly

(D) to position to be used in bead application and tighten.

10. Attach bead hose(s) (12). a. 6-inch: Attach bead hose (12) to bead hopper outlet with hose clamp (11). Plug other bead hopper outlet with cap (13) and clamp (11). b. 12-inch: Attach two bead hoses (12) to bead hopper outlets with hose clamps (11).

11. Route bead hose down to bead dispenser inlet.

NOTE: To avoid bead stoppage in hose during use, make sure bead hose is in an arc curved downward with no kinks or high spots.

12. Mark on bead hose where it will connect to bead dispenser inlet.

13. Cut bead hose on mark and attach to bead dispenser inlet using clamp (11). Hoses must be cut as short as possible to allow good bead flow.

3A5205A

Bead Dispenser Kit

Bead Dispenser Kit

3A5205A

24

23

12

22

1

13

11

3

10

9

3

20

21

7

8 ti31502a

3

4

Bead Dispenser Kit

Dispenser Adjustments

Adjust dispenser plates up or down for desired bead flow. Typical flow rates range between 6 - 8 lb of glass beads per gallon of paint.

Bead dispensers (A) are located behind paint guns. If not adjusted properly, dispensers may miss a short area at end of each paint stripe. Adjust gun cables so guns trigger at midpoint of handle bar trigger. Adjust bead dispensers (A) so beads flow immediately when trigger is pulled. This ensures independent control to keep beads flowing after paint is turned off.

Operation

Operate the striper as in normal striper operation. Refer to LineLazer Repair manual for paint spray tip recommendations.

Only use dry, clean beads. Any moisture or contamination with beads will cause poor bead flow. A window type screen can be used to remove unwanted debris before filling glass bead hopper.

NOTE: To avoid bead stoppage, do not use wet beads or beads that have absorbed moisture. If bead stoppage is occurring, replace with dry beads.

NOTICE

Do not get beads in paint. Beads contaminating the paint supply can damage the pump. Make sure paint supply is covered during bead filling and handling.

Requires two guns and one 12 in. bead dispenser

(see following page for 8 - 10 in. stripe gun orientation).

6 inch stripe

(15 cm)

4 inch stripe

(10 cm) ti6590a

4" 4"

4-12 inch stripe

(10-30 cm)

4"

3A5205A

Bead Dispenser Kit

Gun Orientation for 8 - 12 in.

Stripe Operation

C

B A

For 8 - 10 in. stripe, adjust line width, loosen set screws at (A) and loosen gun adjuster

(B). Tilt guns in for desired line width and tighten. Keep bead dispensers together and parallel to the ground.

NOTE: To avoid glass beads clumping, do NOT store beads in hopper when not in use. Make sure to run beads out of system when done.

8 - 10 in. stripe ti6591a

3A5205A 5

Bead Dispenser Kit - Parts List

Bead Dispenser Kit - Parts List

2

3

7

1

13

11

1

5

14

6

5

10

22

9

12

11

9

20

24 8

21

1

Remove cap (13) and install second hose (12) and clamp (11) for 12-inch bead dispenser

3

5

1

2

6 

7

8

Ref. Part

9

10

11

Description

24Z726 KIT, bead system

15F581 . LEG, hopper, RH (painted)

115087 . PLUG, tubing

15F582 . LEG, hopper, LH (painted)

194666 . LABEL, identification

194668 . LABEL, warning

241437 . HOPPER, beads

. DISPENSER ASSY KIT

(includes 8, 11, 12)

277067 . 6-in. Dispenser Assy

(Parts List, page 7)

245516 . 12-in. dispenser Assy

(Parts List, page 8)

121488 . SCREW, cap, flng hd

101566 . NUT, lock

101818 . CLAMP, hose

6

Qty.

Ref

1

2

1

2

2

1

1

1

4

6

3

23 ti31503a

17

18

19

20

12

13

14

15

21

22

23

Ref. Part Description

194682 . HOSE, beads

403237 . CAP

287680 RING, hopper, frame

100731 WASHER

114988 SCREW, cap, hex hd

100527 WASHER, plain

102040 NUT, lock, hex

17N513 FRAME, mount, bead kit, painted

125626 SCREW, hex hd, flanged

24

WIND DEFLECTOR

277066 6” deflector

245520 12” deflector

198572 WASHER

 Replacement Warning labels are available at no cost.

Qty.

1

1

1

1

1

2

1

1

2

2

1

1

1

3A5205A

6-Inch Dispenser Assembly - Parts List

6-Inch Dispenser Assembly - Parts List

4

14

15

2

3

19

21

1 12

20

13

5

12

17

18

9

16

20

6

12

10

19

8 ti6593a

7

11

7

8

5

6

9

3

4

1

2

Ref.

Part Description

277067 DISPENSER ASSY KIT, beads (see item 8, Bead Dispenser Kit Parts List)

198379 . ROD, connecting

114814 . PIN, bridge

15A264 . LINK, mounting, adjustable

198058 . SCREW, cap, schd, 10-24 x 3/8

15F363 . HOUSING, dispenser, 6 in.

117155 . SPRING, compression

15F357 . DOOR, dispenser, 6 in.

15F366 . PAD, foam, 6 in.

117576 . SCREW, machine, hex wash hd

Qty.

1

1

1

2

8

1

1

1

1

Ref.

Part

14

15

16

17

10

11

12

13

18

19

20

21

Description

198376 . CAP, end, bead dispenser

102598 . SCREW, cap, sch

115483 . NUT, lock

116998 . FITTING, hose, barb

101885 . SCREW, cap, sch

245679 . BLOCK, mounting

198380 . PLATE, slide

100085 . SCREW, thumb

100086 . WASHER

117275 . STUD, button, snap

15F367 . PLATE, slide

166362 . LABEL, identification

Qty.

1

4

2

2

5

1

2

2

2

1

4

3

3A5205A 7

Graco Standard Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by

Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT

LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE .

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy

(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT

MANUFACTURED BY GRACO . These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.

Graco Information

For the latest information about Graco products, visit www.graco.com

.

For patent information, see www.graco.com/patents .

TO PLACE AN ORDER, contact your Graco distributor or call 1-800-690-2894 to identify the nearest distributor.

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

Original instructions.

This manual contains English. MM 3A5205

Graco Headquarters: Minneapolis

International Offices: Belgium, China, Japan, Korea

GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA

Copyright 2017, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.

www.graco.com

Revision A , May 2017

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Key Features

  • Compatible with a wide range of line striping equipment
  • Durable construction for long-lasting use
  • Easy-to-use design for quick and easy setup
  • Hopper capacity of 50 pounds
  • Adjustable flow rate for precise application
  • Optional deflector for increased accuracy
  • Beads can be applied in a variety of widths, from 4 to 12 inches

Related manuals

Frequently Answers and Questions

What is the hopper capacity of the Graco 3A5205A Bead Dispenser Kit?
The hopper capacity is 50 pounds.
What is the adjustable flow rate range of the Graco 3A5205A Bead Dispenser Kit?
The adjustable flow rate range is 6 to 8 pounds of glass beads per gallon of paint.
What is the maximum bead width that can be applied with the Graco 3A5205A Bead Dispenser Kit?
The maximum bead width that can be applied is 12 inches.
Is the Graco 3A5205A Bead Dispenser Kit compatible with the LineLazer 3400?
Yes, the Graco 3A5205A Bead Dispenser Kit is compatible with the LineLazer 3400.

advertisement