Graco 334145B, Glass Beap Dispense Kits Instruction

Add to my manuals
8 Pages

advertisement

Graco 334145B, Glass Beap Dispense Kits Instruction | Manualzz

Instruction

Glass Bead Dispense Kits

334145B

EN

For professional application of traffic marking reflective beads. Not approved for use in

European explosive atmosphere locations.

Models

17B190 Kit: Replaces 12” bead box with 16” bead box

26D112 Kit: Replaces 12” bead box with 18” bead box

IMPORTANT SAFETY INSTRUCTIONS

Read all warnings and instructions in ThermoLazer Operation manual.

Be familiar with the controls and the proper usage of the equipment.

Save these instructions.

Follow these instructions when removing a smaller bead box and installing the larger 16-inch (40cm) or 18-inch

(45cm) bead box on the ThermoLazer 300TC and ProMelt. Refer to the ThermoLazer Repair and Operation manuals as needed for additional information.

Related Manuals

Manual in

English

Description

3A1319 ThermoLazer Operation

3A1320 ThermoLazer Repair ti24093a

2

Removal

Removal

Remove Gas Line

Close manual gas shut-off valve on propane tank.

2. Disconnect gas tube (373) at valve fitting (151).

Discard the hose assembly.

151

373 ti24109a

1. Disconnect gas hose at the tee on the frame above the drive axle. This hose assembly goes to the rear screed burner manifold.

ti24134a

Remove Shroud Door

1. Remove four screws (105) that secure die shroud door (66) to die shroud. Remove and discard the door.

ti24110a ti24159a

66 105

334145B

2. Remove three screws that hold die support rod to die shroud.

105

Removal

2. Remove torch holder (204), mounting screw (141), flatwasher (123), and locknut (97). Save for reuse.

123 97

34 ti24165a

3. Remove die support rod. Save for reuse.

Remove Bead Box Assembly

1. Loosen bead hose retaining clamps (160) and remove hose (189) from manifold (69a) and from bead hopper. Discard the hose assembly.

ti24168a

3. Separate bead dispenser link from bead dispenser box by removing clevis cotter hair pin (268). Save for reuse.

189 160 69a ti24167a

268

4. Loosen screws (6) and slide bead dispenser assembly off the mounting tube.

ti24173a

6 ti24177a

334145B 3

Installation

Installation

Install Bead Box

1. Loosen screws and slide bead dispenser onto bead box support tube. Align bead box drive wheel with center of unit wheel.

3. Install torch holder.

ti24189a

2. Secure to the support tube using the bolts in the two bead box clamps.

4. Slide hose clamps onto bead hoses.

5. Connect hoses to bead hopper and manifolds. Use a screw driver to tighten hose clamps. ti24200a ti24201a

4 334145B

Installation

6. Connect bead dispenser link to bead dispenser box by installing clevis cotter hair pin (268) removed earlier.

Install Shroud Door

1. Slide die support rod (34) removed earlier into die shroud. Secure die support rod to die shroud with three new screws (105) provided.

105 ti24203a

7. Use a cable tie to secure outer bead hose to bead dispenser link.

34 ti24185a

2. Position die shroud door (66) on die shroud and secure with four new screws provided.

ti24208a

66

334145B ti24204a

5

6

Installation

Install Screed Burner Gas Line

1. Apply pipe sealant to hose fitting.

2. Connect gas hose at the tee on the frame above the drive axle.

Checks and Adjustments

Check gas lines and fittings for gas leaks. Use soap and water mixture or LP-gas leak detector to detect gas leaks.

ti24209a

3. Connect gas tube (373) to fittings at both ends.

ti24210a

Refer to Operation and Repair manuals for operation and adjustments.

334145B

17B190 Parts

17B190 Parts

Ref. Part Description

4

5

2

3

1

6

7

8

17B254 BOX, bead, 16” (40 cm), complete

26D108 BOX, bead, 18” (45 cm), complete

15X765 WHEEL, drive, bead

100664 SCREW, set, sch

257399 CLAMP, beadbox

17B264 BRACKET, pivot, mount, 16” bead

26D113 BRACKET, pivot, mount, 18” bead

100101 SCREW, cap, hex hd

111195 SCREW, cap, flnghd

17B915 SCREW, cap, flnghd, 1/2-13

18F299 BOLT, socket head, 1/2-13

119547 NUT, hex, lock, nylon, thin 9

10 17B916 HOSE, bead

11 116789 CLAMP, hose

12 17B917 DOOR, chamber, die, 16” bead

18F263 DOOR, chamber, die, 18” bead

13 112798 SCREW, thread forming, hex hd (not shown)

14 16J469 LABEL, rear burner lighting inst

15 16J468 LABEL, torch lighting inst

16 16H841 LABEL, instructions, SMARTDIE II

334145B

Qty.

1

1

2

4

7

1

2

1

1

1

2

1

1

1

1

1

1

1

1

1

Ref. Part Description

17 17B263 MANIFOLD, torch, die, rear, 16”

18F292 MANIFOLD, torch, di e, rear, 18”

18 555458 FITTING, 1/8M BSPT X 1/8F NPTF

19 16T921 FITTING, flow control, assembly

20 16W411 HOUSING, burner, GEN II

21 16H104 INDICATOR, burner

22 104765 PLUG, pipe headless

23 16H192 BRACKET, support, manifold, rear, L

24 16H107 BRACKET, support, manifold, rear, R

25 113958 RING, retaining, external

26 101550 SCREW, cap, sch

27 159840 ADAPTER

28 16Y844 TUBE, formed, gas

29 118484 FITTING, connector

30 113093 CONNECTOR, pipe

31 125064 VALVE, needle, gas, 1/4 NPT

32 16Y249 HOSE, gas, die back

33 26D622 BRACKET, torch

34 802127 SCREW, cap, hex hd

35 104541 NUT, lock

Qty.

1

1

1

2

4

1

1

2

2

2

1

1

2

1

5

5

5

5

1

1

7

17B254 Parts

16 8

15

17 18

8

1

2

6

11

7

23

24

23

25

3

10

22

4

5 21

9

19 20

10

13

8

9

4

5

2

3

6

Ref. Part

1

7

10

Description

17B256 HOUSING, dispenser, 16” (40 cm)

18F257 HOUSING, dispenser, 18” (45 cm)

SHAFT, knurled (not sold separately)

16H293 BRACKET, left, bead dispenser

16H292 BRACKET, right, bead dispenser

123304 BEARING, sealed

17B258 GATE, poly, 16”

18F256 GATE, poly, 18”

17B259 GATE, backer bar, 16”

18F252 GATE, backer bar, 18”

110631 SCREW, socket head

17B260 ADJUSTER, bead dispenser, 16”

18F255 ADJUSTER, bead dispenser, 18”

123481 SCREW, shoulder, 1/4-20

Qty.

8

1

1

1

1

2

1

1

1

2

1

1

1

1

Ref. Part

17

18

19

20

11

13

15

16

21

22

23

24

25

Description

16U612 PLATE, slide, 1-inch

112310 SCREW, cap sch

17B261 MANIFOLD, assembly

112788 SCREW, cap sch

121112 SCREW, cap socket head

16U614 BRACKET, bead box linkage

295709 SCREW, cap, socket head

15X282 HANDLE, adjuster

114797 GASKET

123261 SCREW, thumb

104034 WASHER, flat

114708 SPRING, compression

119872 SCREW, shoulder ti24105a

Qty.

1

1

2

1

16

5

2

8

32

16

2

1

16

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

Original instructions. This manual contains English. MM

Graco Headquarters: Minneapolis

International Offices: Belgium, China, Japan, Korea

GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA

Copyright 2021, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.

www.graco.com

Revision B , May 2022

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Key Features

  • Enhanced visibility and safety on roads
  • Compatible with ThermoLazer 300TC and ProMelt machines
  • Easy installation and removal
  • Durable construction for long-lasting performance
  • Adjustable bead flow rate for customized application

Related manuals

Frequently Answers and Questions

What are the benefits of using Graco 334145B Glass Bead Dispense Kits?
Improved visibility and safety on roads, especially at night or in low-light conditions
Is the 334145B kit compatible with my existing pavement marking equipment?
Yes, the 334145B kit is designed to work with ThermoLazer 300TC and ProMelt machines.
How do I install the 334145B kit on my machine?
Refer to the included instruction manual for detailed installation instructions.
Can I adjust the amount of beads dispensed?
Yes, the 334145B kit allows for adjustable bead flow rate to meet specific application requirements.
How do I maintain the 334145B kit?
Regular cleaning and inspection are recommended to ensure optimal performance. Refer to the instruction manual for maintenance guidelines.
Download PDF

advertisement