Graco 311440D, Replacement PC Board Kit Instructions

Add to my manuals
2 Pages

advertisement

Graco 311440D, Replacement PC Board Kit Instructions | Manualzz

Instructions - Parts List

Replacement PC Board Kit for:

Ultra Max II 695/795/1095/1595

Ultimate Mx II 695/795/1095/1595

TexSpray

Mark IV, Mark V

311440D

EN

VAC

120 North

America

Model

240 Europe

240 Europe

Multi-cord

110 UK

240 Australia

240 Asia

100 Japan &

Taiwan

Mark IV

Mark V

695

795

1095

Mark V

695

795

1095

Mark V

695

795

1095

Mark V

695

795

1095

695

795

1095

695

795

1095

* Not ETL approved

All models not available in all countries.

695

795

1095

1595

Standard /

Premium

Standard

Premium

Standard

Premium

Standard

Premium

Standard

Premium

Low Boy High Boy

Ultra Max II

249643

248645

249647

249649

249665

249669

249642

249644

249646

249648

249651

249653

249658*

253060

249659*

253059

249636*

249903*

249904

249663

249666

249667

249905

249668

249671

249672

249907

249686

249682

249677

249679

249673

249674

249675

249906

249685

249687

249688

249681

249683

249684

249676

249678

249680

Low Boy High Boy

Ultimate Mx II

826068

826070

826067

826069

826071

826072

826073

826074

826075*

826082

826076*

826081

Pressure Relief Procedure

WARNING

INJECTION HAZARD

System pressure must be manually relieved to prevent system from starting or spraying accidentally. Fluid under high pressure can be injected through skin and cause serious injury. To reduce risk of injury from injection,

splashing fluid, or moving pars, follow Pressure Relief

Procedure

whenever you:

• are instructed to relieve pressure,

• stop spraying,

• check or service any system equipment,

• install or clean spray tip.

Installation

1.

Turn pressure to zero.

2.

Turn ON/OFF switch to OFF.

3.

Unplug power supply cord.

4.

Hold metal part of gun firmly to grounded metal pail.

Trigger gun to relieve pressure.

5.

Lock gun safety latch.

6.

Open pressure drain valve. Leave pressure drain valve open until ready to spray again.

If suspected that spray tip or hose is completely clogged, or that pressure has not been fully relieved after following steps above, VERY SLOWLY loosen tip guard retaining nut or hose end coupling to relieve pressure gradually, then loosen completely. Now clear tip or hose obstruction.

Cutting Instructions

X = Remove

287941

North America, UK, Japan

120 VAC R125 R126 R127

695 X X

795

1095

1595

Mark IV

X

X

X

X

X

X

X

X

Mark V X

287942

International

240 VAC R130 R131 R132

695 X X

795

1095

Mark V

X

X

X

X

X

X

X

CAUTION

Electrostatic discharges can damage components on

PC board. Use a ground strap when handling or installing PC board. Using configurations other than those specified in the image above results in poor sprayer performance.

1.

Follow

Pressure Relief Procedure

.

2.

Remove PC board. See manual 311365 or 311287 (Mark

IV) for procedure.

3.

Cut resistors from PC board (see image above).

4.

Install PC board. See manual 311365 or 311287 (Mark

IV) for procedure.

TO PLACE AN ORDER OR FOR SERVICE, contact your Graco distributor, or call 1-800-690-2894 to identify nearest distributor.

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

Original instructions. This manual contains English. MM 311440

Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea

GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA

Copyright 2004, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.

www.graco.com

Revision D , June 2021

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents