Graco 310743A.fm, XTR 7 Airless Spray Gun Owner's Manual

Instructions
Read warnings and instructions.
XTR™ 7 Airless
Spray Gun
310743A
For use with Protective Coating Materials
XTR 7, Part No. 248609
Heavy Duty RAC tip guard, no tip
7250 psi (50 MPa, 500 bar) Maximum Working Pressure
XTR 7, Part No. 248610
Standard (non-reversing) Dripless™ Tip Guard, 519 Flat Tip
7250 psi (50 MPa, 500 bar) Maximum Working Pressure
XTR 7, Part Nos. 248611, 248612, 248613, 248614
Heavy Duty RAC tip guard, 519 SwitchTip™
7250 psi (50 MPa, 500 bar) Maximum Working Pressure
Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441
Copyright 2004, Graco Inc. is registered to I.S. EN ISO 9001
TI5045A
ll 2 G
Contents
Manual Conventions . . . . . . . . . . . . . . . . . . . . . . . . 3
System Requirements . . . . . . . . . . . . . . . . . . . . . . . 6
Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Gun Trigger Safety . . . . . . . . . . . . . . . . . . . . . . . . . 8
Important . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Pressure Relief Procedure . . . . . . . . . . . . . . . . . . 10
Operating Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Adjusting Spray Pattern . . . . . . . . . . . . . . . . . . 14
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Flushing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Cleaning Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2
Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
XTR 7 Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
XTR 7 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Part Nos. 248609, 248611, 248612, 248613,
248614 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
XTR 7 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Part No. 248610 . . . . . . . . . . . . . . . . . . . . . . . . 32
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
XTR 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 34
Graco Phone Numbers . . . . . . . . . . . . . . . . . . . . . 34
310743A
Manual Conventions
Manual Conventions
Warning
Caution
CAUTION
WARNING
A caution alerts you to possible equipment damage or
destruction if you do not follow instructions.
A warning alerts you to possible serious injury or
death if you do not follow instructions.
Symbols, such as fire and explosion (shown), alert you
to a specific hazard and direct you to read the indicated hazard warnings on pages 4-5.
310743A
Note
A note indicates additional helpful information.
3
Manual Conventions
Warning
Injection Hazard
High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just
a cut, but it is a serious injury that can result in amputation. Get immediate medical attention.
•
Do not point the gun at anyone or at any part of the body.
•
Do not put your hand or fingers over the gun fluid nozzle.
•
Do not stop or deflect leaks with your hand, body, glove, or rag.
•
Do not “blow back” fluid; this is not an air spray system.
•
Follow Pressure Relief Procedure, page 10, when you stop spraying and before cleaning, checking,
or servicing equipment.
•
Use lowest possible pressure when flushing, priming, or troubleshooting.
•
Never spray without tip guard and trigger guard installed.
•
Engage trigger lock when not spraying.
•
Tighten all fluid connections before operating the equipment.
•
Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately. High pressure hose cannot be recoupled; replace the entire hose.
Fire and Explosion Hazard
Solvent and paint fumes in work area can ignite or explode. To help prevent fire and explosion:
•
Use equipment only in well ventilated area.
•
Eliminate all ignition sources, such as pilot lights, cigarettes and plastic drop cloths (potential static
arc).
•
Do not plug or unplug power cords or turn lights on or off when flammable fumes are present.
•
Keep the work area free of debris, including solvent, rags, and gasoline.
•
Ground equipment and conductive objects. See Grounding, page 7.
•
Hold gun firmly to side of grounded pail when triggering into pail.
•
Use only grounded hoses.
•
If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment
until you identify and correct the problem.
Burn Hazard
This equipment is used with heated fluid, which can cause equipment surfaces to become very hot. To
avoid severe burns:
• Do not touch hot fluid or equipment.
4
•
Allow equipment to cool completely before touching it.
•
Wear gloves if fluid temperature exceeds 110° F (43° C).
310743A
Manual Conventions
Warning
Equipment Misuse Hazard
Misuse can cause serious injury or death.
•
For professional use only.
•
Use equipment only for its intended purpose. Call your Graco distributor for information.
•
Read manuals, warnings, tags, and labels before operating equipment. Follow instructions.
•
Check equipment daily. Repair or replace worn or damaged parts immediately.
•
Do not alter or modify equipment. Use only Graco parts and accessories.
•
Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Repair in all equipment manuals.
•
Use fluids and solvents that are compatible with equipment wetted parts. See Repair in all equipment manuals. Read fluid and solvent manufacturer’s warnings.
•
Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
•
Do not use hoses to pull equipment.
•
Comply with all applicable safety regulations.
Toxic Fluid or fumes Hazard
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swallowed.
•
Read Material Safety Data Sheet (MSDS) to know the specific hazards of the fluids you are using.
•
Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.
PERSONAL PROTECTIVE EQUIPMENT
You must wear proper protective equipment when operating, servicing, or when in the operating area of
the equipment to help protect you from serious injury, including eye injury; inhalation of toxic fumes, and
hearing loss. This equipment includes but is not limited to:
•
Protective eye wear
•
Gloves, clothing, and respirator as recommended by the fluid and solvent manufacturer
•
Hearing protection
Recoil Hazard
The gun can recoil when triggered at very high pressure. If unprepared, this could force your hand back
or cause you to fall and injure yourself. Be sure you have firm footing and hold the gun securely.
310743A
5
System Requirements
System Requirements
6
•
Install a bleed-type master air valve on a pneumatic pump air supply line to relieve air trapped between this valve and
the pump after air regulator is shut off. Trapped air can cause the pump to cycle unexpectedly.
•
Install a fluid drain valve between the pump and gun to relieve pressure in displacement pump, hose, and gun. Triggering gun to relieve pressure may not be sufficient. See Pressure Relief Procedure, page 10.
310743A
Grounding
Grounding
WARNING
Read warnings, page 3.
Check your local electrical code and pump/sprayer manual for detailed grounding instructions.
•
Spray gun: ground through connection to a grounded fluid hose and pump/sprayer.
•
Fluid hose: use only grounded hoses.
•
Fluid supply container: follow local code.
•
Object being sprayed: follow local code.
•
Solvent flushing pails: follow local code. Use only conductive metal pails placed on a grounded surface. Do
not place pail on a non conductive surface, such as
paper or cardboard, which interrupts grounding continuity.
•
TI11021
TI11022
To maintain grounding continuity when flushing or
relieving pressure: hold metal part of gun firmly to side
of grounded metal pail, then trigger gun.
TI5047A
TI5046A
310743A
7
Gun Trigger Safety
Gun Trigger Safety
WARNING
Read warnings, page 3.
A wallet-sized warning card with important injection treatment information is included with the gun.
Additional cards are available at no charge. Provide a card to all operators.
1.
To engage trigger lock: turn it to position A. If engaged,
gun will not trigger. Engage trigger lock whenever you stop
spraying to avoid accidental triggering
A
Ti1950A
2.
To disengage trigger lock: turn it to position B.
B
Ti1949A
8
310743A
Important
Important
Do not try to unscrew the gun housing from the handle. Do not use a vice grips or place the gun in a vice to separate the
gun handle from the head. Separating the gun head from the handle in this way may damage or break off the alignment
notch on the gun handle.
Trigger Lock Positions
Ti1948A
Unlocked
310743A
Ti1949A
(Disengaged)
Locked (Engaged)
9
Pressure Relief Procedure
Pressure Relief Procedure
WARNING
Read warnings, page 3.
1.
Engage trigger lock.
TI5049A
2.
Shut off pump.
3.
Disengage trigger lock.
TI5048A
4.
Hold a metal part of the gun firmly to a grounded metal pail.
Trigger gun to relieve pressure.
T12178A
10
310743A
Pressure Relief Procedure
5.
Engage trigger lock.
TI5049A
6.
Open drain valve. Leave drain valve open.
TI5175A
7.
If pressure is not fully relieved:
•
Spray tip is clogged
SwitchTip: Follow procedure on page 16.
Flat Tip: Slowly loosen tip guard retaining nut to relieve pressure. Remove and clear tip.
•
Hose is clogged
Slowly loosen hose end coupling to relieve pressure. Clean hose obstruction.
310743A
11
Operating Gun
Operating Gun
WARNING
Read warnings, page 3.
Strain the fluid if it contains particles that could clog the fluid tip.
1.
Connect a grounded fluid hose.
2.
Without spray tip, flush pump. Use lowest pressure possible.
Solvent
3.
TI5047A
Prime.
Paint
12
310743A
Operating Gun
4.
Follow Pressure Relief Procedure, page 10.
TI5047A
5.
Install spray tip and tip guard.
TI5047A
6.
Start pump and spray onto test paper.
a. Adjust fluid pressure until spray is completely
atomized.
b.
7.
If adjusting pressure does not give a good spray
pattern, follow Pressure Relief Procedure, page
10, then try another tip size.
Trigger gun full-open or full-close.
310743A
13
Operating Gun
Adjusting Spray Pattern
Spray Pattern Size
The spray tip orifice and spray angle determine pattern coverage and size. When you need more coverage, use a
larger spray tip rather than increasing fluid pressure.
Spray Pattern Direction
1.
Follow Pressure Relief Procedure, page 10. Engage trigger lock.
TI5046A
2.
Loosen tip guard retaining nut (C).
C
TI5177A
3.
For a vertical pattern, turn tip guard to position E. For a
D
E
horizontal pattern turn to position D.
TI5179A
TI5178A
4.
Tighten nut (C).
C
TI5180A
14
310743A
Maintenance
Maintenance
Cleaning Spray Tip and Tip Guard
WARNING
Read warnings, page 3.
CAUTION
•
To avoid ruining packings, do not soak entire gun
in solvent.
•
Never hang gun by the tip guard. Damaging tip
guard edges causes paint to collect there.
1.
Follow Pressure Relief Procedure, page 10. Engage
trigger lock.
TI5046A
2.
Clean spray tip with a solvent-soaked brush.
•
Clean front of tip frequently to reduce fluid buildup.
•
Clean tip and tip guard at end of each work day.
310743A
15
Maintenance
If RAC Spray Tip Clogs
WARNING
Read warnings, page 3.
1.
If spray tip clogs while spraying, stop spraying immediately.
2.
Engage trigger lock.
TI5049A
3.
Rotate (G) 180° (arrow points back).
G
TI5181A
TI5181A
4.
Disengage trigger lock.
TI5049A
5.
To remove clog, trigger gun into a pail or onto the ground.
TI5046A
16
310743A
Maintenance
6.
Engage trigger lock.
TI5049A
7.
Rotate (G) 180° to spraying position (arrow points
forward).
G
TI5182A
8.
If tip is still clogged:
a. Engage trigger lock.
TI5048A
b.
Shut off sprayer and disconnect power source.
c.
Open fluid drain valve to relieve pressure.
310743A
17
Flushing
d.
Remove and clean GHD RAC spray tip.
TI5183A
Flushing
WARNING
Read warnings, page 3.
Flush pump and gun before fluid can dry in it. If available, use flushing procedure provided in your pump or sprayer
manual instead of this procedure.
1.
Follow Pressure Relief Procedure, page 10. Engage trigger lock.
TI5046A
2.
TI5049A
Remove tip guard and spray tip. Clean with solvent. See
page 15.
TI5183A
18
310743A
Flushing
3.
Put the pump intake in a grounded pail of compatible
solvent.
4.
Start pump at its lowest pressure.
5.
Disengage trigger lock, then trigger gun into the
paint pail. When solvent appears, release trigger.
TI5048A
6.
TI5047A
Trigger gun into solvent pail. Circulate fluid until system is thoroughly flushed.
310743A
19
Cleaning Filter
7.
Follow Pressure Relief Procedure, page 10.
Engage trigger lock.
TI5046A
TI5049A
Cleaning Filter
WARNING
Read warnings, page 3.
1.
Follow Pressure Relief Procedure, page 10.
2.
Engage trigger lock.
TI5049A
20
310743A
Cleaning Filter
3.
Disconnect trigger guard from gun body beneath diffuser by pushing up on guard hook and pulling it out
of notch.
TI5052A
TI5057A
TI5058A
TI5053A
4.
The trigger guard beneath the gun handle can then
be used as a wrench to loosen the nut.
***See Important note on page 9.***
TI5054A
TI5059A
TI5055A
TI5060A
Loosen
310743A
21
Cleaning Filter
5.
When alignment notches (A) are no longer engaged, use
your hand to twist handle and remove it from gun head.
A
TI5061A
6.
Remove filter.
TI5062A
7.
Clean filter using a soft brush.
TI5063A
8.
Replace filter.
TI5064A
22
310743A
Cleaning Filter
9.
Attach handle to gun head by hand twisting handle
until notches (A) on the gun head and handle meet
and are aligned.
A
TI5065A
10.Use trigger guard to tighten the nut.
TI5066A
11.Reattach the trigger guard to the gun.
TI5067A
310743A
23
Repair
Repair
Repair Kit 248837 is available. Parts included with the kit are marked with *.
Disassembly
WARNING
Read warnings, page 3.
Follow Pressure Relief Procedure, page 10.
1.
Engage trigger lock.
TI5049A
2.
Disconnect fluid hose. Remove tip and tip guard (20).
20
TI5184A
3.
Using a wrench, remove the cap (4) with spring (5)
(releases spring tension on needle).
4
5
T15185A
24
310743A
Repair
4.
Remove the valve seat (10*) and gasket (9*).
10*
9*
T15186A
5.
Holding the needle with tool (A*) remove the needle
retainer (6).
A*
6
T15187A
6.
Pull the needle (8*) out.
8*
TI5188A
7.
Using a socket wrench, remove the seal retainer (2*)
from the back of the gun. Use a pick to remove the gasket (3*).
2*
3*
T15189A
310743A
25
Repair
8.
Clean and replace parts as needed.
If you need to remove the trigger
1.
Using a wrench, remove screw (12) from the trigger stud (11).
To avoid losing parts, be ready for two actuator pins (7) to fall out of the gun body (1) when the trigger (16) is
removed.
2.
Slide the trigger stud (11) out of the gun body, and
remove the trigger (16).
3.
Before installing trigger grease the actuator pins (7) and
12
trigger stud (11).
7
1
11
16
T15190A
26
310743A
Repair
Assembly
Use clean, petroleum jelly where grease is indicated.
1.
Press a new gasket (3*) into the gun body. Lightly
grease the seal retainer (2*) and install. Torque to
48-72 in-lbs (5-8 N•M).
2*
3*
TI5189A
2.
Lightly grease and replace the needle (8*). Press the
8*
needle through the seal retainer.
TI5188A
3.
Apply light-strength Loctite™ to needle threads. Hold-
A*
ing the needle with tool (A*), install needle retainer
(6). Tighten until it bottoms out.
6
TI5187A
310743A
27
Repair
4.
9*
Lightly grease valve seat (10*) threads. Squeeze the trigger to retract the needle and install gasket (9*) and valve
seat (10*). Torque valve seat to 26-32 ft-lbs (35-43 N•M).
10*
TI5186A
5.
Grease and install the spring (5) and cap (4). Tighten the
cap to 10-13 ft-lbs (8-10 N•M)
4
5
TI5185A
Test Gun Before Using
1.
Engage trigger lock. Connect fluid hose to gun.
TI5049A
28
TI5175A
310743A
Repair
2.
Start and prime the pump.
3.
Disengage the trigger lock and trigger the gun into a
metal waste container.
T5047A
TI5048A
4.
Release the trigger; the gun should immediately stop spraying and there should not be any leaks. If there is a
problem, follow the Pressure Relief Procedure on page 10. Check through Assembly procedure and correct
problem.
5.
Install tip and tip guard before regular use.
TI5176A
310743A
29
XTR 7 Parts
XTR 7 Parts
22
2*
1
12
21
19b
19d
8*
4
7
9*
20
3*
5
10*
6
11
19a
15b
14*
18
19c
26
24
15a
16b
16a
16c
13
TI5192B
30
310743A
XTR 7 Parts List
XTR 7 Parts List
Part Nos. 248609, 248611, 248612, 248613, 248614
Ref.
No.
Part No. Description
1
15E178 BODY, gun
Qty.
1
Ref.
No.
Part No. Description
16c
287451 TRIGGER (see table below)
1
18
245994 RETAINER, RAC tip
1
19
GHDxxx SWITCH, tip 519 size included
(includes items 19a - 19d)
(see table below)
1
Qty.
2*
----
SEAL, retainer assembly
1
3*
----
GASKET
1
4
15A864 CAP, end
1
5
117350 SPRING, compression
1
19a
----
SEAL, fluid
1
6
15E088 RETAINER, needle
1
19b
----
GASKET
1
7
15E085 PIN, actuator
2
19c
----
TIP, spray hd RAC
1
1
19d
----
SCREW, mach pn h
1
1
24
15B958 O-RING, packing (included with
item 13)
1
26
287032 FILTER, 60 mesh (included with
gun)
1
8*
9*
----
STEM, valve
156766 GASKET
10*
----
SEAT, valve
1
11
----
PIN, pivot (included with items 16a, 1
16b, 16c)
12
----
SCREW, cap hex hd (included with 1
items 16a, 16b, 16c)
13
248952 HANDLE, tube assembly (includes
item 24)
1
14*
179733 SEAL, sleeve
1
15a
276997 HANDLE, gun (see table below)
1
15b
15E083 HANDLE, gun (see table below)
1
16a
287449 TRIGGER (see table below)
1
16b
287450 TRIGGER (see table below)
1
287033 FILTER, 100 mesh
287034 FILTER, 60 and 100 mesh combo
29▲
222385 WARNING CARD
1
34▲
187346 WARNING TAG
1
*
Parts included in Repair Kit 248837, purchased separately. Installation tool included.
▲
Replacement Danger and Warning labels, tags, and
cards are available at no cost.
Reference Nos.
Gun Part No.
15a
248609
310743A
248611
✔
248612
✔
15b
16a
✔
✔
16b
✔
248613
✔
248614
✔
✔
16c
19
✔
✔
✔
✔
✔
✔
31
XTR 7 Parts List
XTR 7 Parts List
Part No. 248610
Ref.
No.
Part No. Description
1
15E178 BODY, gun
Qty.
1
Ref.
No.
Part No. Description
16a
287449 TRIGGER
1
20†
220222 TIP, guard
1
21
163519 SPRAY TIP, flat, 519 size
1
22†
166969 TIP, gasket
1
24
15B958 O-RING, packing (included with
item 13)
1
26
1
Qty.
2*
----
SEAL, retainer assembly
1
3*
----
GASKET
1
4
15A864 CAP, end
1
5
117350 SPRING, compression
1
6
15E088 RETAINER, needle
1
7
15E085 PIN, actuator
2
287032 FILTER, 60 mesh (included with
gun)
1
287033 FILTER, 100 mesh
1
287034 FILTER, 60 and 100 mesh combo
8*
9*
----
STEM, valve
156766 GASKET
10*
----
SEAT, valve
1
29▲
222385 WARNING CARD
1
11
----
PIN, pivot (included with item 16a)
1
34▲
187346 WARNING TAG
1
12
----
SCREW, cap hex hd (included with 1
item 16a)
13
248952 HANDLE, tube assembly (includes
item 24)
1
*
Parts included in Repair Kit 248837, purchased separately. Installation tool included.
14*
179733 SEAL, sleeve
1
▲
15b
15E083 HANDLE, gun
1
Replacement Danger and Warning labels, tags, and
cards are available at no cost.
†
Parts included in Kit 240251, purchased separately.
32
310743A
Technical Data
Accessories
Part No. 246297: 180° Spray Nozzle
Part No. 194744: Packing Repair Tool
7/8-14 UNC-2B
Included in Repair Kit 248837
Front Extension: 7/8-14 UNF-2B (tip guard and tip not
included)
TI235028
Part No. 246294:10” (0.25 m)
Part No. 246295:15” (0.4 m)
Part No. 246296: 18” (0.5 m)
TI243295A
Technical Data
XTR 7
Maximum Working Pressure. . . . . . . . . . . . . . . . . . . . . . .
Fluid Orifice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fluid Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum Fluid Temperature . . . . . . . . . . . . . . . . . . . . . .
Sound Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sound Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7250 psi (50 MPa, 500 bar)
0.090" (2.3 mm)
1/4 npsm(m)
160°F (71°C)
103 dB(A)*
111.6 dB(A)*
stainless steel, polyethylene, nylon, polypropylene, acetal,
Wetted Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
carbide, polyurethane
*Results are maximum readings taken at 6000 psi (41 MPa, 414 bar), with HD427 tip, using water. Sound power level
was tested to ISO 3744-1981.
310743A
33
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material
and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by
Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be
defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance
of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Phone Numbers
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.
Phone: 612-623-6921 or Toll Free: 1-800-328-0211, Fax: 612-378-3505
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
This manual contains these languages: English, French, German, Spanish
Corporate Office: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441
www.graco.com
Printed in USA 310743A
8/ 2004

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project