Graco 334146A - Double Bead Box Kit 17B587 (8") or 17B361 (12"), Kit Instructions

Add to my manuals
8 Pages

advertisement

Graco 334146A - Double Bead Box Kit 17B587 (8

Kit Instructions

Double Bead Box Kit

17B587 (8”) or 17B361 (12”)

For adding a second bead box to the ThermoLazer 200 or 200TC.

To be used on 200/200TC models only.

334146A

EN

Models

17B587 – 8” (20cm), 17B361 – 12” (30cm)

IMPORTANT SAFETY INSTRUCTIONS

Read all warnings and instructions in ThermoLazer Operation manual.

Be familiar with the controls and the proper usage of the equipment.

Save these instructions.

Follow these instructions when adding the second bead box to an existing 8-inch (20cm) or 12-inch (30cm) bead box on the ThermoLazer 200 or 200TC. Refer to the ThermoLazer Repair and Operation manuals as need for additional information.

Related Manuals:

3A1319

3A1320 ti24490a

Preparation

Preparation

1. Close manual gas shut-off valve on propane tank.

2. Disconnect hose from tank.

ti24109a ti24499a

5. Loosen screws on hose clamps and remove bead hose from dispenser and bead hopper. Save for reuse.

ti24489a

3. Remove propane tank from unit.

4. Cut tie wrap that secures propane line to bead hose.

ti24502a

2 334146A

Preparation

6. Remove screws from bead hopper. Save for reuse.

Screws are accessible from the propane tank side of the box.

7. Remove bead hopper. Dispose of bead hopper.

9. Install two angular inserts (A) on bead dispenser with screws provided and tighten screws.

ti24514a ti24504a

8. Loosen screw and remove bead dispenser engagement wheel. Dispose of wheel and screw.

ti24506a

334146A 3

4

Installation

Installation

1. Slide rear bead box down through slots on angular brackets to lock into place.

3. Slide bead dispenser engagement wheel pulley onto long axle.

2. Slide single pulley over long axle.

ti24519a ti24523a

4. Secure pulley and wheel into place with retaining ring (engagement wheel with pulley will rotate freely).

ti24524a

5. Slide pulley onto short axle.

ti24522a ti24521a

334146A

6. Install belts onto pulleys.

Installation

8. Attach pulley guard and tighten two screws.

ti24520a

7. Align pulleys as shown below and tighten screws.

ti24528a

9. Install new dual compartment bead box using

screws saved in Preparation Step 6.

334146A ti24525a ti24527a

10. Attach bead hose (Saved in Preparation Step 5.)

from rear bead box to rear dispenser and tighten hose clamps.

5

Installation

11. Attach bead hose from front bead box to front dispenser and tighten hose clamps.

The rear bead dispenser has a higher drop rate than the front bead dispenser.

6 ti24529a

334146A

Parts 17B361, 17B587

Parts 17B361, 17B587

1

5

4

6

21

2

20

19

7 8

41

42

31

17

19 15

16

18

32

33

27

29

4

16

12

19

26

5

25

13 10 11

10

9

34

21

20

30

31

56

57

54 ti24530a

334146A 7

Parts List 17B361, 17B587

Ref. Part

7

8

5

6

3

4

1

2

9

10

11

12

13

14

15

16

17

18

Description

123261 SCREW, thumb

123481 SCREW, shoulder, screw, 1/4-20

295709 SCREW, cap, socket head

15X282 HANDLE, adjuster

110631 SCREW, socket head

16Y163 BRACKET, left, bead dispenser

123304 BEARING, double sealed

114797 GASKET

15X274 GATE, poly

15X275 GATE, bar

SCREW, cap, shoulder

112310 Kit 17B587

112310 Kit 17B361

SHAFT, adjuster

16Y166 Kit 17B587

15X281 Kit 17B361

PLATE, slide, 1"

16U612 Kit 17B587

16U612 Kit 17B361

SPRING, compression

114708 Kit 17B587

114708 Kit 17B361

104034 WASHER, plain

Kit 17B587

Kit 17B361

119872 SCREW, shoulder

Kit 17B587

Kit 17B361

SHAFT, knurled

16Y161 Kit 17B587

16A333 Kit 17B361

16Y162 BRACKET, right, bead dispenser

Qty.

2

2

8

1

1

1

1

1

1

2

3

4

1

8

12

8

12

16

24

8

12

1

1

Ref. Part Description Qty.

19

20

38

39

40

41

34

35

36

37

30

31

32

33

21

22

23

29

16A805 SHAFT, short

HOUSING, dispenser

16Y160 Kit 17B587, 8” (20cm)

16Y172 Kit 17B361, 12” (30cm)

16Y168 GASKET, cover

16Y169 MANIFOLD, cover

106084 SCREW, machine, pan head

104705 SCREW, cap, shoulder

100050 SCREW, set, shoulder

113983 RING, retaining, ext.

16Y230 CLAMP, hose

17B456 BOX, double bead box

17B463 WHEEL, drive bead, assembly

17C509 HOSE, bead hose 20.5"

17B555 COVER, belt

514930 SCREW, cap, socket head

123526 BELT, outer

123527 BELT, inner

16A802 PULLEY, double

16A803 PULLEY, large

42 16A804 INSERT, bead box 2

44  16A276 LABEL, ISO symbols warn & instru 1

45

46

16E335 LABEL, brand, GRACO

16X975 LABEL, brand, THERMOLAZ-

2

1

1

1

1

1

1

2

1

1

2

1

4

1

6

2

1

1

1

1

47

ER200TC, FR

16Y468 GASKET, beads box 1

 Replacement Danger and Warning labels, tags, and cards are available at no cost.

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

Original instructions.

This manual contains English. MM 334146

Graco Headquarters: Minneapolis

International Offices: Belgium, China, Japan, Korea

GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA

Copyright 2014, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.

www.graco.com

Revision A, October 2014

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement