Graco 312761D, PR70 and PR70v Integrated Heat Instructions


Add to my manuals
20 Pages

advertisement

Graco 312761D, PR70 and PR70v Integrated Heat Instructions | Manualzz

Instructions - Parts

PR70 and PR70v

Integrated Heat

For controlling material temperature in heated tanks and hoses.

Models LC0250, LC0251,

LC0252, LC0253

Important Safety Instructions

Read all warnings and instructions in all sup plied manuals. Save these instructions.

312761D

EN

Assembly LC0252 Shown ti12577a

2

Supplied Manuals

Contents

Supplied Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Component Identification . . . . . . . . . . . . . . . . . . . . 4

Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Connect Electrical Cord . . . . . . . . . . . . . . . . . . . 5

Install Low Power Temperature Control Modules 6

Connect 3-wire Module Power . . . . . . . . . . . . . . 6

Adjust Rotary Switch . . . . . . . . . . . . . . . . . . . . . . 7

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Cable Connections . . . . . . . . . . . . . . . . . . . . . . . 8

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Install Upgrade Token . . . . . . . . . . . . . . . . . . . . 10

Clean . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Circuit Breaker . . . . . . . . . . . . . . . . . . . . . . . . . 11

Diagnostic Information . . . . . . . . . . . . . . . . . . . 11

Simplified Wiring Schematic . . . . . . . . . . . . . . . 11

Wiring Schematic . . . . . . . . . . . . . . . . . . . . . . . 12

Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Circuit Breakers . . . . . . . . . . . . . . . . . . . . . . . . 17

Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Graco Ohio Standard Warranty . . . . . . . . . . . . . . 20

Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . 20

Supplied Manuals

Assemblies with a Standard Display Module include manual 312393. Assemblies with an

Advanced Display Module include manuals 312759 and 312760.

PR70 and PR70v Operation and Parts Manuals

Part Description

312393 PR70 with Standard Display Module Opera tion and Maintenance Manual

312759 PR70 and PR70v with Advanced Display

Module Operation and Maintenance Manual

312760 PR70 and PR70v with Advanced Display

Module Repair and Parts Manual

MD2 Dispense Valve Manual

Part Description

312185 MD2 Dispense Valve Instructions and Parts

Manual

PR70 and PR70v Feed Systems Manual

Part Description

312394 PR70 and PR70v Feed Systems Manual

PR70 and PR70v Integrated Heat Manual

Part Description

312761 PR70v Integrated Heat Instructions - Parts

Manual

312761D

Warnings

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama tion point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applicable.

WARNING

ELECTRIC SHOCK HAZARD

This equipment must be grounded. Improper grounding, setup, or usage of the system can cause elec tric shock.

Equipment With Grounding Plug

• Turn off and disconnect power cord before servicing equipment.

• Use only grounded electrical outlets.

• Use only 3-wire extension cords.

• Ensure ground prongs are intact on power and extension cords.

• Do not expose to rain. Store indoors.

Hard-Wired Equipment

• Turn off and disconnect power at main switch before disconnecting any cables and before servicing equipment.

• Connect only to grounded power source.

• All electrical wiring must be done by a qualified electrician and comply with all local codes and regu lations.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.

• Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical Data in all equipment manuals.

• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information about your material, request MSDS forms from distributor or retailer.

• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manu facturer’s replacement parts only.

• Do not alter or modify equipment.

• Use equipment only for its intended purpose. Call your distributor for information.

• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

• Do not kink or over bend hoses or use hoses to pull equipment.

• Keep children and animals away from work area.

• Comply with all applicable safety regulations.

312761D 3

4

Component Identification

Component Identification

AF

AE

AK

Assembly LC0253 Shown

F IG . 1: Heat Control Box

Key:

AA Zone 1

AB Zone 2

AC Zone 3

AD Zone 4

AE Electrical Disconnect Switch

AF Fan

AH

AG ti12577a

AJ

AG Integrated Heat Power Inlet

AH Integrated Heat Power Outlet to Machine

AJ CAN Connection Output to

Machine

AK Heat Control Box

AD

AC

AB

AA

312761D

Grounding

Grounding

This product must be grounded. In the event of an elec trical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric cur rent. This product is equipped with a chord having a grounding wire. A 3-blade grounding plug must be installed or the machine may be hard wired. The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Improper installation of the grounding plug is able to result in a risk of electric shock. The wire with insulation having an outer surface that is green with or without yel low stripes is the grounding wire. Do not modify the plug provided; if it does not fit the outlet, have the proper out let installed by a qualified electrician. Only connect the product to an outlet having the same configuration as the plug. Do not use an adapter with this product.

appropriate gauge wire for the machine amperage.

See the following table.

Number of Zones installed in Heat

Control Box

3

4

1

2

Rating

(Amps)

30

30

40

40

Install Plug

Gauge (mm 2 ) /

Number of Wires

10 (2.59) / 3

10 (2.59) / 3

8 (3.26) / 3

8 (3.26) / 3

The equipment must be grounded. Grounding reduces the risk of static and electric shock by provid ing an escape wire for the electrical current due to static build up or in the event of a short circuit.

Improper installation of the grounding plug is able to result in a risk of electric shock. The wire with insula out yellow stripes is the grounding wire.

tion having an outer surface that is green with or with

-

-

Installation

2.

For machines that will not be hard-wired, install a

3-blade 240V, 1-phase grounding plug onto cord (129). The machine must use a receptacle that accepts the plug on the product.

For machines that will be hard-wired, hard-wire the machine. The grounding wire must be used.

Connect Electrical Cord

Machine may be hard-wired or installed using a plug.

Improper wiring may cause electric shock or other serious injury if work is not performed properly. Have a qualified electrician perform any electrical work. Be sure your installation complies with all National, State and Local safety and fire codes.

1. Each machine comes with a permanent 10 ft power cable without a plug. If a permanent extension cable must be installed onto the existing cable or if an extension cord is necessary, be sure to use the

312761D 5

Installation

Install Low Power Temperature

Control Modules

The low power temperature control modules are installed in the Heat Control box at the factory. If a low power temperature control module must be replaced, perform the following procedure.

124a

124

8. Use two hex head cap screws (124a) to install low power module (124) onto base module (125).

9. Change rotary switch position on new low power temperature control module. See

Adjust Rotary

Switch on page 7.

10. Reconnect CAN cables (113, 130) and power cables.

Connect 3-wire Module Power

120

119

125

Connecting the power must be performed by a quali fied electrician. The equipment must be grounded.

Grounding reduces the risk of static and electric shock by providing an escape wire for the electrical current due to static build up or in the event of a short circuit.

The wire with insulation having an outer surface that is green with or without yellow stripes is the grounding wire.

116 ti12703a

F IG . 2

Remove Old Low Power Temperate Control Module

1.

On units with a grounding plug, unplug unit from wall.

On hard-wired units, use facility power switch to turn off incoming power.

2. Unplug data connection and power cables from low power temperature control modules. Do not discon nect other end of cables.

3. Remove hex head cap screws (124a) from low power temperature control module.

4. Remove low power module (124).

5. Remove four socket head cap screws (119).

6. Remove base module (125).

Install New Low Power Temperate Control Module

7. Use four socket head cap screws (119) to install base module (125) onto enclosure back panel (120).

4

3

2

1 ti12627b

Main Power

Breaker

F IG . 3: Breaker Numbering

141

141a

6 312761D

Installation

There is one breaker for each heated hose or heated tank. The lower number breakers are used for the

heated tanks if installed. See F IG . 3. For example, if

there are two heated tanks installed and two heated hoses, breakers #1 and #2 are used for the heated tanks and breakers #3 and #4 are used for the heated hoses. If there is one heated tank and one heated hose, then breaker #1 is used for the heated tank and breaker

#2 is used for the heated hose. Each breaker has a dif ferent rating so it is important that the correct breaker is used.

The 3-wire module power is connected in the Heat Con trol box at the factory. The power cord (118) for each low power temperature control module has a connector on one end and three power leads on the other. The three power leads must be connected to the appropriate breaker (114) and ground terminal (116).

1. Connect the power cord connector to the low power temperature control module.

2. Connect the green wire to any unused ground termi nal block (116).

3. Find the breaker with the same number as the mod -

ule as shown in F IG . 3 on page 6 and F

IG . 6 on page 9.

4. Connect the black and white wires to the breaker (141) labeled with the same number as the module. The black and white wires can connect to either terminal (141a) in the same breaker (141).

Set the rotary switch (S) to the specific selection accord ing to the settings listed in the following table.

F IG . 4

Low Power Temperature Control Module

S

Low Power Temperature Control Module

Rotary Switch Settings

The modules must always be set to the zone num ber shown on the label above the module.

Switch

Setting

3

4

1

2

Rotary Switch Location

Zone

3

4

1

2 ti12361a

Adjust Rotary Switch

The rotary switch setting must only be adjusted on new low power temperature control modules after installation.

The rotary switch setting indicates which zone number the low power temperature control module will control in the system. The low power temperature control module uses a 16-position rotary switch.

312761D 7

8

Setup

Setup

Cable Connections

2

1

3 ti12356a

4

7

F IG . 5: Low Power Temperature Control Module Cable Connections

1 Overtemperature Switch Connection

2 RTD Temperature Sensor Connection

3 Output Power Connection

4 DC Output Connection

5 Input Power Connection

6 CAN Connections

7 Base

The overtemperature switch connection (1), RTD tem perature sensor connection (2), and output power connection (3) connect to the respective components of a temperature control option. The display module must be updated to specify which zone number is used with which temperature control option. See the PR70 and

PR70v Operation manual referenced at the beginning of this manual for more information.

ti12357a

5

6

312761D

Data Cable Connections

4

130

130

3

2

130

1 ti12625a

113

F IG . 6: Data Cable Connections

The low power temperate control modules must be con nected together using the female-female CAN cables (130) as shown in F IG . 6. Then they must be con nected to the display module using the female-male

CAN cable (113).

Setup

312761D 9

Operation

Operation

See the PR70 and PR70v Operation manual referenced at the beginning of this manual for operating instruc tions.

Maintenance

Install Upgrade Token

1. Ensure system is inactive and control power is on.

2. Remove access cover (C).

C

4. Press and hold the left red token upload button (M) for three seconds. The red indicator light (L) will flash up to three seconds after the software is uploaded.

5. Remove token (T).

6. Replace access cover (C).

7. Repeat procedure for all low power temperature control modules.

8. Turn machine power off then on after all modules are upgraded.

Clean

Keep heat sink fins clean at all times. Wipe the fins clean with a dry cloth or clean them using compressed air.

Do not use conductive cleaning solvents on the low power temperature control modules.

Heat Sink Fins ti12358a

F IG . 7: Remove Access Cover

3. Insert and press token (T) firmly into slot.

There is no preferred orientation of token.

ti12357a

F IG . 9: Clean Heat Sink Fins

S

L

F IG . 8: Install Token

T

10 ti12359a

M

312761D

Troubleshooting

Troubleshooting

Circuit Breaker

If the circuit breaker is tripped, manually flip the breaker back to the “on” position. Find and correct the problem before continuing operation.

Diagnostic Information

7

Module Status LEDs

Table 1: LED Status Signal

Signal Description

Green on Low power temperature control mod ule is powered up.

Internal communication in progress.

Yellow

Red solid Low power temperature control mod ule failure.

Red flashing Software is updating.

F IG . 10: LED Signals

Simplified Wiring Schematic

208-240V

50/60 Hz

1 phase

312761D ti12357a

LED

Signals

Fan

GFEP

Circuit

Breaker #1

Circuit

Breaker #2

Circuit

Breaker #3

Circuit

Breaker #4

Circuit

Breaker #5

Low Power

Temp Cont

Module #1

Low Power

Temp Cont

Module #2

Low Power

Temp Cont

Module #3

Low Power

Temp Cont

Module #4

Machine

Power

11

Troubleshooting

Wiring Schematic

F IG . 11: Wiring Schematic, Page 1 of 2

12 312761D

Troubleshooting

F IG . 12: Wiring Schematic, Page 2 of 2

312761D 13

Parts

Parts

108, 107

121

118

105

124

117

130

144

102

119

125

120

132

129

115

135

134

133

135

116

102

106

146

145

1

1

1

141

116

115

123

131

101

104

103

127

128

126

113

114

122

117

110

136

14

198 ti12471b

121

111 112

Assembly LC0252 Shown

109 102

1 Heated hose and heated tank circuit breakers shown for reference only. See

Circuit Breakers on page 17 for part numbers.

312761D

Parts

Ref

101

102

103

104

105

106

107

114

115

116

117

108

109

110

111

112

113

118

119

120

121

122

123

124

125

Description

GUARD, fan,

80 mm x 80 mm

SCREW, panhead machined

NUT, lock, hex

FAN, brushless,

80 x 80 x 25, 24 VDC

CONNECTOR, straight,

M8, 3-PIN, solder

SWITCH, disconnect,

3-pole, 40A

SHAFT, disconnect, elec

tric

HANDLE, disconnect, electric

FILTER, screen, fan, 80 mm x 80 mm

SCREW

FOOT, BUMPER

SCREW

CABLE, CAN, male / female, 0.4 m

CONNECTOR, thru,

M12, male / female

BLOCK, end stop, termi

nal, tan, 35 mm RA

BLOCK, terminal, spg,

4P, ground, 600V/20A

CORD, power, v-lock,

C14/C13, 10A

CORD, power, v-lock,

15P/C13, 10A

SCREW, socket head cap, 10-32 x 0.62, stain

less steel

PANEL, back, enclosure,

12 in.

PANEL, back, enclosure,

20 in.

ENCLOSURE,

12 x 12 x 6, 2 load

ENCLOSURE,

20 x 12 x 6, 4 load

GRIP, cord,

0.51 - 0.71, 3/4

GRIP, cord,

0.35 - 0.63, 3/4

SCREW, pan head machined,

M5 - 0.8 x 12 mm

MODULE, low power,

Graco Control Architec

ture

MODULE, Graco Control

Architecture, base

LC0250

Control Box, Heat,

1 Load, 240V

LC0251

Control Box, Heat,

2 Load, 240V

LC0252

Control Box, Heat,

3 Load, 240V

121560

105676

105334

121556

121590

121568

121149

121148

121559

120916

123698

120885

121226

121612

123384

123686

(Qty 3)

121599

(Qty 2)

121598

(Qty 1)

113003

(Qty 4)

121584

121563

121603

121725

256270

(Qty 1)

289697

(Qty 1)

121560

105676

105334

121556

121590

121568

121149

121148

121559

120916

123698

120885

121226

121612

123384

123686

(Qty 3)

121599

(Qty 3)

121598

(Qty 2)

113003

(Qty 8)

121584

121563

121603

121725

256270

(Qty 2)

289697

(Qty 2)

121560

105676

105334

121556

121590

121568

121149

121148

121559

120916

123698

120885

121226

121612

123384

123686

(Qty 4)

121599

(Qty 4)

121598

(Qty 3)

113003

(Qty 12)

121585

121565

121171

121725

256270

(Qty 3)

289697

(Qty 3)

121559

120916

123698

120885

121226

121612

123384

123686

(Qty 4)

121599

(Qty 5)

121598

(Qty 4)

113003

(Qty 16)

LC0253

Control Box,

Heat, 4 Load,

240V

121560

Qty

1

105676

105334

121556

10

4

1

121590

121568

121149

121148

1

1

1

2

4

4

1

1

1

1

2

121585

121565

121171

1

1

1

1

1

1

121725

256270

(Qty 4)

289697

(Qty 4)

2

312761D 15

Parts

Ref Description

126 † COVER, heat box

127 NUT, hex

128 WASHER, plain #10

129 CORD, 10/3, 40A,

SOOW, CU, 600V

CORD, 8/3, 30A, SOOW,

130

131

CU, 600V

CABLE, CAN, 90 female /

90 female

RAIL, DIN

LC0250

Control Box, Heat,

1 Load, 240V

15U672

110911

120907

065054

514014

(Qty 0.6)

132

133

GASKET, enclosure, heat, Graco Control

Architecture

CONNECTOR, bus bar, 2 phase, 4 poles

CONNECTOR, bus bar, 2 phase, 6 poles

CONNECTOR, bus bar, 2 phase, 8 poles

CONNECTOR, bus bar, 2

134

135

136 phase, 10 poles

TERMINAL

CAP

CONNECTOR, power, panel mount

LABEL, zone1 137

138

139

140

LABEL, zone2

LABEL, zone3

LABEL, zone4

141 CIRCUIT, breaker,

2-pole, 10A, C type

142 † ENCLOSURE, Graco

143

144

145

146

Control Architecture, door

CABLE, CAN, M12 x

M12, 5P, female / female, straight x right angle

TERMINAL, ring, #8

AWG, 1/4 in. stud

CIRCUIT, breaker, 63A,

GFI

BRACKET, disconnect,

197

40A

† LABEL, electric shock

198 PLATE, legend, serial number

199 † PLUG, retainer

121566

(Qty 1)

15U740

121648

121649

121558

15V283

121634

277674

(Qty 1)

121685

123421

123687

16C235

XXXXX

293564

123699

LC0251

Control Box, Heat,

2 Load, 240V

LC0252

Control Box, Heat,

3 Load, 240V

15U672

110911

120907

065054

121597

(Qty 1)

514014

(Qty 0.83)

121566

(Qty 2)

15U741

121648

121649

121558

15V283

15V284

121634

277674

(Qty 2)

121685

123421

123687

16C235

XXXXX

293564

123699

121158

121597

(Qty 2)

514014

(Qty 0.83)

121566

(Qty 3)

15U742

121648

121649

121558

15V283

15V284

15V285

121634

277674

(Qty 3)

121685

123421

123687

16C235

XXXXX

293564

123699

† Part not shown.

Replacement Danger and Warning labels, tags, and cards are available at no cost.

15U743

121648

121649

121558

15V283

15V284

15V285

15V286

121634

277674

(Qty 4)

121685

LC0253

Control Box,

Heat, 4 Load,

240V Qty

1

2

2

12

121158

121597

(Qty 3)

514014

(Qty 0.83)

121566

(Qty 4)

12

1

1

1

1

1

1

1

2

2

1

1

1

1

123421

123687

16C235

XXXXX

293564

123699

1

1

1

1

1

1

16 312761D

Circuit Breakers

See the PR70 and PR70v Repair - Parts manual refer enced at the beginning of this manual to find the heated hose and heated tank assembly numbers for your sys tem.

Heated Hose Circuit Breakers

Installed Heated

Hose Package

LC0195

LC0196

LC0197

LC0198

LC0199

LC0200

LC0201

LC0202

LC0203

LC0204

LC0205

LC0206

LC0207

LC0208

LC0209

LC0210

LC0211

LC0881

LC0882

LC0883

LC0884

LC0885

LC0886

LC0887

LC0888

LC0889

LC0890

LC0891

LC0190

LC0191

LC0192

LC0193

LC0194

Circuit Breaker

121632

121630

121631

121632

121632

121633

121630

121631

121632

121630

121631

121632

121630

121631

121632

121632

121633

121630

121631

121632

121630

121631

121632

121630

121631

121632

121632

121633

121630

121631

121632

121630

121631

Heated Tank Assembly Circuit Breakers

Installed Heated

Tank Assembly

LC0237

LC0238

LC0254

LC0255

LC0259

LC0260

Circuit Breaker

121633

121635

Parts

312761D 17

Parts

18 312761D

Technical Data

Technical Data

Electrical Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208-240V 50/60 Hz, 1 phase for heat - 10 kW max.

(Qty 4) 2500W outputs

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 lb (13.6 kg) - 1 and 2 Zone Models

50 lb (22.7 kg) - 3 and 4 Zone Models

Dimensions

C

A ti12626a

B

Assembly LC0253 Shown

F IG . 13: Dimensions

Ref

A (height)

B (width)

C (depth)

1 and 2 Zone

Assemblies in. (mm)

12 (305)

12 (305)

6 (152)

3 and 4 Zone

Assemblies in. (mm)

20 (508)

12 (305)

6 (152)

California Proposition 65

CALIFORNIA RESIDENTS

WARNING: Cancer and reproductive harm – www.P65warnings.ca.gov.

ti12628a

312761D 19

Graco Ohio Standard Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by

Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT

LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE .

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy

(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT

MANUFACTURED BY GRACO . These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.

Graco Information

Sealant and Adhesive Dispensing Equipment

For the latest information about Graco products, visit www.graco.com

.

For patent information, see www.graco.com/patents .

TO PLACE AN ORDER, contact your Graco distributor, go to www.graco.com, or call to identify the nearest distributor.

If calling from the USA: 1-800-746-1334

If calling from outside the USA: 0-1-330-966-3000

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

Original instructions.

This manual contains English. MM 312761

Graco Headquarters: Minneapolis

International Offices: Belgium, China, Japan, Korea

GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA

Copyright 2008, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.

www.graco.com

Revision D, July 2021

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals