Graco 332298H. G3 Pro Automatic Lubrication Pump Instructions

Add to my manuals
48 Pages

advertisement

Graco 332298H. G3 Pro Automatic Lubrication Pump Instructions | Manualzz

Instructions

G3 Pro Automatic

Lubrication Pump

332298H

EN

For dispensing of NLGI Grades #000 to #2 greases and oil with at least 40cSt. For

Professional Use Only.

Not approved for use in explosive atmospheres or hazardous locations.

Part Nos., page 3

5100 psi (35.1 MPa, 351.6 bar) Pump Output Pressure

5000 psi (34.4 MPa, 344.7 bar) Fill Inlet Pressure

Important Safety Instructions

Read all warnings and instructions in this manual. Save all instructions.

Conforms to ANSI/UL 73

Certified to CAN/CSA

Std. 22.2 No 68-09

3132066

24V and 110-240VAC Pumps ONLY

2

Table of Contents

Table of Contents

4Part / Model Numbers . . . . . . . . . . . . . . . . . . . . . . 3

2 Liter Models . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

4 Liter Models . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

8 Liter Models . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

12 Liter Models . . . . . . . . . . . . . . . . . . . . . . . . . . 3

16 Liter Models . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Understanding the Model Number . . . . . . . . . . . 4

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Typical Installation . . . . . . . . . . . . . . . . . . . . . . . . 9

Typical Installation - With Remote

Fill Manifold . . . . . . . . . . . . . . . . . . . . . . . . 10

Optional Installation - Without Remote

Fill Manifold . . . . . . . . . . . . . . . . . . . . . . . . 11

Choosing an Installation Location . . . . . . . . . . . 12

System Configuration and Wiring . . . . . . . . . . . 13

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Connecting to Auxiliary Fittings . . . . . . . . . . . . 17

Setting Pump Outlet Volume . . . . . . . . . . . . . . 18

Loading Grease . . . . . . . . . . . . . . . . . . . . . . . . . 18

Auto-Fill Shut Off . . . . . . . . . . . . . . . . . . . . . . . 21

Fill Oil Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Prime the pump . . . . . . . . . . . . . . . . . . . . . . . . 24

Quick Setup Guide . . . . . . . . . . . . . . . . . . . . . . . . . 25

Pro Model Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Control Panel Overview (F

IG

. 24) . . . . . . . . . . . 26

Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Advanced Programming . . . . . . . . . . . . . . . . . . . . 30

Models with Firmware 6.03 and later.

DMS Models with Firmware 7.07 and later. . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Models with Firmware 6.06 and later for non-DMS models. Models with

Firmware 7.09 and later for DMS models . . 35

Run Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Time Control . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Fault / Warning Scenarios . . . . . . . . . . . . . . . . . 38

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Parts - 2 Liter Models . . . . . . . . . . . . . . . . . . . . . . 41

Parts - 4 Liter and Larger Models . . . . . . . . . . . . 42

Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Mount Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Technical Specifications . . . . . . . . . . . . . . . . . . . . 47

California Proposition 65 . . . . . . . . . . . . . . . . . . 47

Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 48

332298H

Part / Model Numbers

Part / Model Numbers

The Part Number is a six-digit unique number that is only used to order the G3 Pump. Directly related to this six digit Part Number is the configured Graco Model Number. This configured number identifies the distinct features of a specific G3 Pump. To help you understand each component that makes up the Model Number see Understanding

Your Model Number, page 4. The tables below shows the relationship between each Part Number and its related

Model Number.

2 Liter Models

Part

Numbers

Model Number

96G011 G3-G-24PR-2L0L00-R0C00000 X

96G012 G3-G-24PR-2LFL00-R0C00000 X

96G013 G3-G-ACPR-2L0L00-0D000000 X

96G014 G3-G-ACPR-2LFL00-0D000000 X

96G027 G3-G-12PR-2L0000-00C00000

96G028 G3-G-24PR-2L0000-00C00000 X

96G029 G3-G-ACPR-2L0000-0D000000 X

96G033 G3-G-12PR-2L0L05-00C00000

96G034 G3-G-24PR-2L0L05-00C00000 X

96G070 G3-A-24PR-2L0L00-R0C00000 X

96G079 G3-A-ACPR-2L0L00-0D000000 X

96G255 G3-G-12PR-2L0L07-00C00000

8 Liter Models

Part

Numbers

Model Number

96G069 G3-G-24PR-8L0L00-R0C00000 X

96G072 G3-A-24PR-8L0L00-R0C00000 X

96G076 G3-G-ACPR-8L0L00-0D000000 X

96G081 G3-A-ACPR-8L0L00-0D000000 X

96G136 G3-G-12PR-8L0000-00C00000

96G138 G3-G-24PR-8L0000-00C00000 X

96G140 G3-G-ACPR-8L0000-0D000000 X

96G148 G3-G-12PR-8L0L05-00C00000

96G150 G3-G-24PR-8L0L05-00C00000 X

96G208 G3-G-ACPR-8LAL00-0D00000 X

96G214 G3-G-24PR-8LAL05-00C00000 X

96G257 G3-G-24PR-8L0L07-00C00000 X

96G268 G3-G-24PR-8LLL05-00C00000

96G270 G3-G-24PR-8LFL07-00C00000 X

4 Liter Models

Part

Numbers

Model Number

96G068 G3-G-24PR-4L0L00-R0C00000 X

96G071 G3-A-24PR-4L0L00-R0C00000 X

96G073 G3-G-24PR-4LFL00-R0C00000 X

96G075 G3-G-ACPR-4L0L00-0D000000 X

96G080 G3-A-ACPR-4L0L00-0D000000 X

96G082 G3-G-ACPR-4LFL00-0D000000 X

96G135 G3-G-12PR-4L0000-00C00000

96G137 G3-G-24PR-4L0000-00C00000 X

96G139 G3-G-ACPR-4L0000-0D000000 X

96G147 G3-G-12PR-4L0L05-00C00000

96G149 G3-G-24PR-4L0L05-00C00000 X

96G211 G3-G-24PR-4LAL05-00C00000 X

96G256 G3-G-24PR-4L0L07-00C00000 X

12 Liter Models

Part

Numbers

Model Number

96G077 G3-G-ACPR-120L00-0D000000 X

96G163 G3-G-24PR-120L05-00C00000 X

96G247 G3-G-24PR-120L00-R0C00000 X

16 Liter Models

Part

Numbers

Model Number

96G078 G3-G-ACPR-160L00-0D000000 X

96G167 G3-G-24PR-160L05-00C00000 X

332298H 3

Part / Model Numbers

Understanding the Model Number

Use the Code Sample provided below to identify each component’s location in the Model Number. The options for each component that make up the code are provided on the lists below.

NOTE: Some pump configurations are not available. Contact Graco Customer Service or your local Graco distribu tor for assistance.

Code Sample:

G 3 a

P R 0 0 0 0 0 0 b b c c - d d e f g g - h i j k m n p q

Code a: Pump Fluid Type

• G = Grease

• A = Oil

Code bb: Power Source

• 12 = 12 Volts DC

• 24 = 24 Volts DC

• AC = 100 - 240 Volts AC

Code cc: Operation Control

• PR = Pro (Timer) Control

Code dd: Reservoir Capacity (Liters)

• 2L = 2 Liters

• 4L = 4 Liters

• 8L = 8 Liters

• 12 = 12 Liters

• 16 = 16 Liters

Code e: Reservoir Feature

• F = Follower Plate Installed

• 0 = No Follower Plate

• A =Auto-Fill Shut Off

• L = Top Fill

Code f: Low Level Option

• L = Low Level with Controller

• 0 = No Low Level monitoring

Code gg: Options

• 00 = No Options

• 05 = 5 Pin CPC power cable

• 07 = No Power Cord

Code h, i, j, k, m, n, p, q

NOTE: Codes h - q relate to a specific location on the G3 pump. See F IG . 1 for these locations.

• C = CPC

• D = DIN

• R = Remote Manual Run

• 0 = Not populated h i j k m n p q

4

F IG . 1

332298H

Warnings

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-spe cific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable.

WARNING

ELECTRIC SHOCK HAZARD

This equipment must be grounded. Improper grounding, setup, or usage of the system can cause electric shock.

• Turn off and disconnect power at main switch before disconnecting any cables and before ser vicing or installing equipment.

• Connect only to grounded power source.

• All electrical wiring must be done by a qualified electrician and comply with all local codes and regulations.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.

• Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical Data in all equipment manuals.

• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Spec ifications in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For com plete information about your material, request MSDS from distributor or retailer.

• Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.

• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine man ufacturer’s replacement parts only.

• Do not alter or modify equipment. Alterations or modifications may void agency approvals and create safety hazards.

• Make sure all equipment is rated and approved for the environment in which you are using it.

• Use equipment only for its intended purpose. Call your distributor for information.

• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

• Do not kink or over bend hoses or use hoses to pull equipment.

• Keep children and animals away from work area.

• Comply with all applicable safety regulations.

332298H 5

6

Warnings

WARNING

SKIN INJECTION HAZARD

High-pressure fluid from dispensing device, hose leaks, or ruptured components will pierce skin.

This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.

• Do not point dispensing device at anyone or at any part of the body.

• Do not put your hand over the fluid outlet.

• Do not stop or deflect leaks with your hand, body, glove, or rag.

• Follow the Pressure Relief Procedure when you stop dispensing and before cleaning, checking, or servicing equipment.

• Tighten all fluid connections before operating the equipment.

• Check hoses and couplings daily. Replace worn or damaged parts immediately.

PRESSURIZED EQUIPMENT HAZARD

Over-pressurization can result in equipment rupture and serious injury.

• A pressure relief valve is required at each pump outlet.

• Follow the Pressure Relief Procedure in this manual before servicing.

PLASTIC PARTS CLEANING SOLVENT HAZARD

Many cleaning solvents can degrade plastic parts and cause them to fail, which could cause serious injury or property damage.

• Use only compatible solvents to clean plastic structural or pressure-containing parts.

• See Technical Specifications in all equipment manuals for materials of construction. Consult the solvent manufacturer for information and recommendations about compatibility.

332298H

332298H

Warnings

WARNING

MOVING PARTS HAZARD

Moving parts can pinch, cut or amputate fingers and other body parts.

• Keep clear of moving parts.

• Do not operate equipment with protective guards or covers removed.

• Equipment can start without warning. Before checking, moving, or servicing equipment, follow the Pressure Relief Procedure and disconnect all power sources.

PERSONAL PROTECTIVE EQUIPMENT

Wear appropriate protective equipment when in the work area to help prevent serious injury, including eye injury, hearing loss, inhalation of toxic fumes, and burns. Protective equipment includes but is not limited to:

• Protective eyewear, and hearing protection.

• Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufacturer.

7

Installation

Installation

Component Identification

N

A

Top Fill Models

O

N

Grease Models

Oil Models

E

L

M

I Grease Models with Follower

Plate

R

D

J

H

96GXXX

G3-G-24PR-2LFL00-R0C00000

Auto-Fill Shut Off Models

F

IG

. 2:

Key:

A Reservoir

B Pump Element (1 included. Can accommodate 3 total)

C Pressure Relief Valve (Not included / required for each

outlet - Available from Graco. See Parts, page 45.)

D Zerk Inlet Fill Fitting (1 included / grease models only)

E Pump Outlet Plug (2 included)

F Volume Control Spacers (2 included. More spacers = less output volume per stroke) (also see F IG . 11, page 18)

G Fuse (DC models only - Not included, not shown.

Available from Graco. See Parts, page 44.)

H Control Panel

I Power / Sensor Panel (both sides; only one side shown)

J Part Number / Model Number example only shown, (see

pages 4, Understanding the Model Number, for details)

K Power Cord (Not shown)

8

F

B

L Follower Plate (grease models only / not available on all grease models)

M Vent Hole for Follower Plate (grease models only / not available on all grease models)

N Fill cap (oil models only)

O Top Fill Lid

R Auto-Fill Shut Off

332298H

Installation

Typical Installation

Series Progressive Divider Valve Installations

B

A

F

IG

. 3

A Connected to fused power source

B Pressure relief valve (Not included/required for each outlet - user supplied. See Parts, page 45)

C Series progressive divider valves (Divider Installations)

D To lube points

C

D

332298H 9

Installation

Typical Installation - With Remote Fill Manifold

The installation shown is only a guide for selecting and installing system components. Contact your Graco distributor for assistance in planning a system to suit your needs.

E

H

F

S

N R

J

T

M

K

L

P

Q

A

B

D

C

F IG . 4

Key:

A G3 Pump

B Auto-Fill Shut Off Valve

C Auto-Fill Inlet

D G3 Reservoir

E Remote Fill Reservoir

F Remote Fill Pump

G Supply Hose (user supplied)

H Air Supply to Refill Pump

J Supply Hose (user supplied)

K Pressure Relief Valve

L Drain Hose

M Fill Coupler/Inlet (quick disconnect)

N Fill Manifold ❖

P Fill Manifold Outlet

Q Fill Manifold Vent Port

R Pressure Gauge

S Pressure Regulator and Gauge

T Pressure Relief Knob

To relieve the stall pressure in the fill line a fill mani fold (N) must be installed in the system.

10 332298H

Installation

Optional Installation - Without Remote Fill Manifold

The installation shown is only a guide for selecting and installing system components. Contact your Graco distribu tor for assistance in planning a system to suit your needs.

NOTE: The remote filling station pump stalls (dead-heads) when the reservoir is full. If the pump does not stall

(dead-head) there is a leak in the system.

B

H

F

U J

C

S

V

Y

L

D

A

E

L1

L2

W

F IG . 5

Key:

A G3 Pump

B Auto-Fill Shut Off Valve

C Auto-Fill Inlet

D G3 Reservoir

E Remote Fill Reservoir

F Remote Fill Pump

H Relief Valve

J Supply Hose (user supplied)

L Drain Tube

L1 Option - To reservoir

L2 Option - To overflow container

S Pressure Regulator and Gauge

U Pressure Relief Valve

V Quick Disconnect

W Overflow Container

Y Supply Hose Pressure Relief Valve ❖

To relieve the stall pressure in the fill line a ball valve

(Y) must be installed in the system.

332298H 11

Installation

Choosing an Installation Location

AUTOMATIC SYSTEM ACTIVATION HAZARD

If the system is equipped with has an automatic timer (user supplied) that activates the pump lubrica tion system when power is connected or when exit ing the programming function, unexpected activation of the system could result in serious injury, including skin injection and amputation.

Before you install or remove the lubrication pump from the system, disconnect and isolate all power supplies and relieve all pressure.

• Select a location that will adequately support the weight of the G3 Pump and lubricant, as well as all plumbing and electrical connections.

• Refer to the mounting hole layouts provided in the Mounting Pattern section of this manual,

page 46. No other installation configuration

should be used.

• Use designated mounting holes and provided configurations only.

• Always mount the G3 oil models upright.

• Mount top fill G3 pump so that there is a mini mum clearance of four inches (4.0 in.) (10.2 cm) above the reservoir to allow for lid removal and filling.

• If the G3 grease model is going to be operated in a tilted or inverted position for any period of time, you must use a model that includes a fol lower plate, otherwise the G3 must be mounted upright. Refer to your model number to confirm if a follower plate was installed on your pump.

See page 4, Understanding the Model Number

to identify this character in your model number.

• Use the three fasteners (included) to secure the

G3 to the mounting surface.

• Some installations may require an additional reservoir support bracket. See table below for bracket information.

• In high vibration environments, additional isola tion at mounting point is necessary. See table below.

• AC pumps are not recommended when high vibration or shock is present.

Part No Description

571159 Reservoir bracket and strap

125910 L-Bracket for pump

127665 USP to G-Series mounting bracket

132187 Isolator mounting kit

12 332298H

Installation

System Configuration and Wiring

Grounding

The equipment must be grounded to reduce the risk of static sparking and electric shock. Electric or static sparking can cause fumes to ignite or explode.

Improper grounding can cause electric shock.

Grounding provides an escape wire for the electric current.

Improper installation of the grounding conductor may result in a risk of electric shock. This product must be installed by a qualified electrician in compli ance with all state and local codes and regulations.

If the product is permanently connected:

• It must be installed by a qualified electrician or ser viceman.

• It must be connected to a grounded, permanent wiring system.

If an attachment plug is required in the end use application:

• It must be rated for the product electrical specifica tions.

• It must be an approved, 3-wire grounding type attachment plug.

• It must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.

• When repair or replacement of the power cord or plug is required, do not connect the grounding wire to either flat blade terminal.

Fuses

NOTICE

Fuses (user supplied) are required on all DC mod els. To avoid equipment damage:

• Never operate G3 Pump DC models without a fuse installed.

• A fuse of the correct voltage must be installed in line with the power entry to the system.

Fuse Kits are available from Graco. The following Table identifies the correct fuse to use for your input voltage and the corresponding Graco Kit number.

Input Voltage Fuse Value Graco Kit No.

12 VDC

24 VDC

7.5 A

4 A

571039

571040

Recommendations for Using Pump in

Harsh Environments

• Use pump with CPC style power cable.

• If using a DIN style power or alarm harness with a right angle mating connector, make sure the con nector does not exit the unit in the UP direction.

• Use a corrosion preventative electrical grease on all contacts.

332298H 13

Installation

Remote Illumination Response

The following tables include graphical representations of the connector as it appears on the unit, a pin-out associ ated with the connector and a typical installation wiring diagram. An internal representative wiring diagram is included where it is deemed useful.

Wire colors provided on these pages only refer to the power cable provided by Graco with this product.

Unit in OFF Mode

Unit in ON Mode

Warning Condition

Fault Condition

Off

On

Standard Remote Illumination

(via 5 wire CPC power cable)

Tri-Color Remote Illumination

Off

Green

Toggles On and Off once per second Yellow

Toggles On and Off once per second Red

(M12 Connector)

Wiring and Installation Diagrams

The following Table identifies the wiring and installation diagrams provided in this manual.

Diagram Symbol Page #

Power DIN AC

15

Power DIN DC

Power CPC DC

Illuminated Manual Run Input

15

16

Kits: 571030, 571031,

571032, 571033

14 332298H

Power DIN AC - 15 foot

4

Pin and Related Wire Color (F

IG

. 6)

Pin Pin Name

1 Line

Neutral

Color

Black

2 White

3 Not Used Not Used

Ground Green

Installation

Power DIN DC - 15 Foot

4

Pin and Related Wire Color (F

IG

. 7)

Pin

1

2

3

Pin Name

-VDC

+VDC

Not Used

Not Used

Color

Black

White

Not Used

Green

F

IG

. 6

332298H

F IG . 7

15

Installation

Power CPC DC - 2 Wire

Part No.: 127783: 15 ft. (4.5 m)

Pin and Related Wire Color (F

IG

. 8)

Pin Pin Name

1

4

5

2

3

6

7

Not Used

-VDC

+VDC

Not Used

Not Used

Not Used

Not Used

Color

Not Used

Black

White

Not Used

Not Used

Not Used

Green

Power CPC DC - 5 Wire

Part No.: 127780: 15 ft (4.5 m)

Part No.: 127781: 20 ft (6.1 m)

Part No.: 127782: 30 ft (9.1 m)

An Illuminated Remote Run Button Kit: 571030, 571031 for starting a manual run cycle if used in conjunction with a 5-wire CPC cable, is available from Graco. Con tact your local Graco distributor or Graco Customer

Service for additional information about these kits.

Pin and Related Wire Color (F

IG

. 9)

2

3

4

Pin Pin Name

1 Not Used

-VDC

5

6

7

+VDC

LIGHT

Manual Run

Switch

Not Used

Not Used

Color

Not Used

Black

Red

White

Orange

Not Used

Green

F IG . 9

F IG . 8

16 332298H

Setup

Setup

Pressure Relief

Follow the Pressure Relief Procedure whenever you see this symbol.

Connecting to Auxiliary Fittings

This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from pressurized fluid, such as skin injection, splash ing fluid and moving parts, follow the Pressure Relief

Procedure when you stop dispensing and before cleaning, checking, or servicing the equipment.

Relieve pressure in system using two wrenches working in opposite directions on pump element and pump element fitting to slowly loosen fitting only until fitting is loose and no more lubricant or air is leaking from fitting.

NOTE: When loosening pump element fitting, do NOT loosen pump element . Loosening pump element will change the output volume.

NOTICE

Do not attach unsupported equipment to auxiliary fit tings such as fill ports and pump element. Attaching unsupported equipment to these fitting can result in irreparable housing damage.

• Always use two wrenches working in opposite directions when connecting anything to pump ele -

ment or auxiliary fittings. See F IG . 10 for an exam

ple.

• Torque pump element fittings to 50 in. lbs (5.6

N•m).

• When connecting pump element into housing torque to 50 in. lbs (5.6 N•m).

Pressure Relief Valves

To prevent over-pressurization, which can result in equipment rupture and serious injury, a pressure relief valve appropriate for the lubrication system must be installed close to every pump outlet to alle viate unintended pressure rises in the system and protect the G3 pump from damage.

• Only use a pressure relief valve that is rated for no more than the working pressure of any com ponent installed in the system. See Technical

Data, page 42.

• Install a pressure relief valve close to every pump outlet; before any auxiliary fitting.

NOTE: A pressure relief valve can be purchased from

Graco. See Parts, page 45.

F IG . 10

332298H 17

Setup

Setting Pump Outlet Volume

NOTE:

• Before making any adjustments to pump volume,

Relieve Pressure

following procedure on page 17.

• Only use Graco supplied spacers to control output volume.

1. Use a wrench to turn pump element counter-clock wise to loosen. Do not remove entire pump ele ment. Only back pump element out enough to allow spacer to be slid on or off.

2. If needed, remove or insert spacers to achieve required pump output volume. A tool may be needed to facilitate removal.

Pump volume control is set using either no (0) spacers, 1 or 2 spacers (F IG . 11).

Do not use more than 2 spacers to adjust output volume.

No. Spacers

2

1

0

Output Volume / Minute cubic inches cubic cm

0.12

0.18

0.25

2

3

4

NOTE:

• The amount of dispensed volume can vary depend ing on external conditions such as lubricant tem perature and back pressure from downstream connections.

• Use of these volume adjustment in conjunction with setting the ON time of the pump will allow for con trol of the output volume.

• Use these volume adjustments as a starting point and adjust as necessary to ensure desired lubrica tion dispense.

• Tighten pump element fitting. Torque fitting to 50 in. lbs (5.6 N•m).

F IG . 11

Loading Grease

To ensure optimal performance from the G3:

• Only use NLGI #000 - #2 greases appropriate for your application, automatic dispensing, and the equipment’s operating temperature. Consult with machine and lube manufacturer for details.

• The reservoir can be filled using a hand operated pump, pneumatic pump or electric transfer pump.

• Do not overfill (F

IG

. 14).

• Do not operate G3 without reservoir attached.

NOTICE

• Always clean inlet fitting (D) (F IG . 12) with a clean dry cloth prior to filling reservoir. Dirt and/or debris can damage pump and/or lubri cation system.

• Care must be used when filling the reservoir using a pneumatic or electric transfer pump to not pressurize and break the reservoir.

D

F

IG

. 12

18 332298H

Setup

Models without a follower plate:

1. Connect fill hose to Zerk inlet fitting (D) (F

IG

. 13).

Models with Top Fill

E

D

F IG . 13

2. For higher viscosity fluids, start pump to rotate stir ring paddle during fill to prevent air pockets from forming in grease.

Start pump by pressing the manual run button.

3. Fill reservoir with NLGI grease to max fill line.

NOTE: Vent port, located in rear of reservoir, should not be used as an overfill port/indicator.

MOVING PARTS HAZARD

Moving parts can pinch, cut or amputate fingers and other body parts.

• Keep clear of moving parts.

• Do not operate equipment with lid removed.

• Disconnect power before removing lid.

1. Disconnect the power from the equipment.

NOTE : If battery disconnect is not available, remove the power cord (F IG . 15).

F IG . 14

4. Remove fill hose.

332298H max fill line F IG . 15

2. Clean the top of the lid and the area around the top of the reservoir to ensure that no debris falls into the reservoir when the lid is removed.

3. Turn the lid counterclockwise to remove.

4. Place the lid in a clean area to avoid debris getting into the inside of the lid or threads.

5. Fill the reservoir with new clean grease.

6. Make sure that no contaminants enter the reservoir.

19

Setup

NOTICE

Any debris or dirt accidentally introduced into the res ervoir should be removed immediately. Do not allow the pump to operate until any debris or dirt are removed.

Operating the pump with debris or dirt in the reservoir, may damage the pump, down stream equipment, and bearings.

7. Clean the threads on the reservoir and the lid.

8. Replace the lid onto the reservoir, turning clockwise

(approximately 1 3/4 turns).

9. Reconnect the power to the equipment.

Models with a follower plate:

1. Connect fill hose to Zerk inlet fitting (D) (F

IG

. 13).

2. For higher viscosity fluids, start pump to rotate stir ring paddle during fill to prevent air pockets from forming in grease.

Start pump by pressing the manual run button.

3. Fill reservoir with grease until seal of follower plate breaches the vent hole (F

IG

. 16) and the majority of air is expelled from the reservoir.

vent hole

F IG . 16

NOTE: Vent port, located in rear of reservoir, should not be used as an overfill port/indicator.

4. Remove fill hose.

Changing Greases

When changing greases, always use compatible fluids or greases.

20 332298H

Setup

Auto-Fill Shut Off

Load Grease

To ensure optimal performance from the G3:

• Only use NLGI #000 - #2 greases appropriate for your application, automatic dispensing, and the temperature. Consult with machine and lube manu facturer for details.

• Do not overfill.

• Do not operate G3 without reservoir attached.

NOTICE

Care must be used when filling the reservoir using a pneumatic or electric transfer pump to not pressur ize and break the reservoir.

Change Greases

When changing greases, always use compatible fluids or greases.

The Auto-Fill Shut Off is used for refilling the G3 reser voir in an automatic lubrication system. As fluid is added to the reservoir, it pushes the plate valve up to the top of the reservoir. The plate valve then pushes the valve pin and closes the inlet fluid path.

When the fluid refilling path closes, the refilling line pressurizes and brings the refilling pump to a pressur ized stall condition.

NOTE: The operator must monitor system while filling the reservoir to prevent overfilling.

COMPONENT RUPTURE HAZARD

The maximum working pressure of each component in the system may not be the same. To reduce the risk of over-pressurizing any component in the sys tem, be sure you know the maximum working pres sure of each component. Never exceed the maximum working pressure of the lowest rated com ponent in the system. Over-pressurizing any compo nent can result in rupture, fire, explosion, property damage and serious injury.

Regulate input pressure to the remote fill pump so that no fluid line, component or accessory is over pressurized.

Remote Fill with Remote Fill Manifold

The reference letters used in the following instructions

refer to the Typical Installation diagram, page 10.

The fill valve is used to relieve pressure in the refill line and to reset the Auto Fill Shut Off. See Fill Valve instruc tion manual 333393. Graco fill valve, part no. 77X542 is available. Contact your local Graco distributor.

1. Pull out and hold the Pressure Relief Knob (T) long enough to relieve line pressure between Fill Mani fold (N) and Auto-Fill Shut Off Valve (B).

2. Verify the Auto-Fill Shut Off (B) pin is down, indicat ing it is reset (F IG . 17). pin down

The remote filling station pump stalls (dead-heads) when the reservoir is full, causing the supply system pressure to rise to the maximum output pressure of the filling station pump. To help prevent equipment damage or serious injury caused by pressurized fluid, such as skin injection or injury from splashing fluid, always use a remote filling station pump with a maxi mum output pressure of 5100 psi (35.1 MPa,

351.6 bar) and use supply hoses with a minimum pressure rating of 5100 psi (35.1 MPa, 351.6 bar).

F IG . 17

3. Remove yellow Dust Cover from Fill Coupler (M).

332298H 21

Setup

4. Connect Supply Hose (J) between the Remote Fill ing Station Pump (F) and Fill Coupler port marked with an “I”.

5. Start Remote Filling Station Pump (F).

6. When the G3 Reservoir (D) is filled:

• the Remote Filling Station Pump (F) stalls

(dead-heads),

• the Auto-Fill Shut Off (B) pin pops up as shown in F IG . 18,

• the Pressure Gauge (R) rises to the fill pump’s set pressure.

NOTE: If the pump does not stall (dead-head) there is a leak in the system.

pin up

Remote Fill without Remote Fill Manifold

The reference letters used in the following instructions

refer to the Typical Installation diagram, page 11.

1. A supply hose pressure relief valve (Y) and overflow container (W) (for collecting excess fluid that drains during pressure relief) must be installed in an easily accessible location between the remote filling sta tion pump (F) and the Auto-Fill Shut Off (B). This pressure relief valve is used to relieve pressure in the refill line and to reset the Auto-Fill Shut Off. See

Typical Installation, starting on page 9.

A Pressure Relief Kit: 247902 is available from

Graco. Contact your distributor or Graco Customer

Service for additional information about this kit.

2. Connect Supply Hose (J) at Quick Connect (V).

3. Turn on remote filling station pump (F) and fill the

G3 reservoir (D) until the indicator pin on the

Auto-Fill Valve pushes up as shown in F

IG

. 19. The pressure in the refill pump (F) builds and the pump stalls.

pin up

F IG . 18

NO

7. Turn off the Remote Filling Station Pump (F).

8. Pull out and hold the Pressure Relief Knob (T) long enough to relieve line pressure between Fill Mani fold (N) and Auto-Fill Shut Off Valve (B) and between Remote Filling Station Pump (F) and Fill

Manifold (N).

NOTE: The length of time it takes to vent varies depending on the system design and installation. In some installations it may be necessary to repeat Step 8 to ensure pressure is relieved.

9. Disconnect Supply Hose (J) at Fill Coupler (M).

10. Replace yellow Dust Cover over Fill Coupler (M).

F IG . 19

4. Turn off the air supply (H) to pump (F).

5. Relieve remote filling station pump pressure using the following Remote Filling Station Pressure Relief procedure:

22 332298H

Setup

Remote Filling Station Pressure Relief

The reference letters used in the following instructions refer to the Typical Installation diagrams starting on

page 9.

The following Pressure Relief Procedure is only used with the Auto-Fill Shut Off Valve to relieve remote filling station and lubricant supply line pressure.

Fill Oil Unit

• Only use oil appropriate for your application, auto matic dispensing, and the equipment’s operating temperature. Consult with machine and lube manu facturer for details.

• Do not overfill (F IG . 21).

• Do not operate G3 without reservoir attached.

• Only use oils with viscosity at least 40 cSt.

a

This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from pressurized fluid, such as skin injection, splash ing fluid and moving parts, follow the Pressure Relief

Procedure when you stop dispensing and before cleaning, checking, or servicing the equipment.

a. To relieve pressure between the Refill Pump (F) and Auto-Fill Shut Off (B), open ball valve (bv)

(F IG . 20). Pressure will be released and excess fluid will drain out of the drain tube (L) and into the lubrication overflow container (W).

F IG . 21

1. Remove fill cap (a).

2. Pour oil into reservoir to max fill line (b).

3. Replace fill cap. Hand tighten cap, securely.

b

Y

L

W

F IG . 20: b. Close supply hose pressure relief valve (Y) when all pressure has been relieved.

6. Disconnect the supply hose (J) from Quick Connect

(V).

332298H 23

Setup

Prime the pump

NOTE: It is not necessary to prime pump every time pump is filled with lubricant.

Pump only requires priming the first time it is used or if it is allowed to run dry.

1. Loosen pump element fitting (F IG . 22).

NOTE: When loosening pump element fitting, do NOT loosen pump element . Loosening pump element will change the output volume

2. Only run pump until air is no longer dispensed with the lubricant coming out of element fitting (F

IG

. 23).

F IG . 23

3. Tighten pump element fitting using two wrenches working in opposite directions (F IG . 22).

F IG . 22

24 332298H

Quick Setup Guide

!!

%#

Quick Setup Guide

332298H 25

Pro Model Setup

Pro Model Setup

Control Panel Overview (F

IG

. 24)

NOTE: Programming instructions begin on page 27.

DISPLAY

• A blinking LED under HH, MM, SS or ## indicates type of measurement unit you are setting; i.e., HH is hours.

• A blinking number on the display indi cates the G3 is in SETUP MODE.

• In RUN MODE displayed numbers count up or down. See Time ON and Time

OFF.

ON TIME

• LED lights when ON Time sequence is running.

• Display shows time as MM:SS

(minutes and seconds).

i.e., 08:30 is 8 minutes: 30 sec onds.

• Times lubrication cycle.

OFF TIME

• LED lights when OFF Time sequence is running.

• Value is entered in HH:MM.

• Displays in HH:MM (hours and minutes) when > 1 hour.

• Displays in MM:SS (minutes and second)

HH MM SS ##

!

ON

MM : SS

OFF

HH : MM

ALARM ICONS

LED next to icon lights when a fault / warning event occurs

during a run cycle. See page 38

for a complete description of these alarm scenarios.

LEFT DIRECTION ARROW /

RESET

• In SETUP MODE: moves cursor in display one field to the left.

• In RUN MODE: single press clears warning.

• In RUN MODE: pressing for one second ends run cycle if there are no warnings.

• In ALARM MODE: pressing and holding for 3 seconds clears fault / warning and switches cycle to OFF MODE.

UP and DOWN ARROW

• Hold both the UP and DOWN ARROW but tons down together for 3 seconds to enter

SETUP MODE.

• In SETUP MODE, increases or decreases number values shown in display.

LOCK ICON

• LED next to icon lights indicating PIN is required to enter setup.

• In SETUP MODE LED lights when setting up the

PRELUBE

LED next to icon lights indicat ing Prelube function is en abled.

RIGHT DIRECTION ARROW /

MANUAL RUN / ENTER:

• In SETUP MODE: saves entry, moves cursor in display one field to the right or to the next setup step.

• In RUN MODE: starts a man ual run cycle.

F IG . 24

26 332298H

Pro Model Setup

Instructions

Powering Units With Controllers

By default, units with controllers are set to operate in a timed mode with 1 minute of

ON time and 8 hours of OFF time. The unit should be powered up in OFF mode, counting down from the 8 hours. If the unit powers up in ON mode and has not been primed, hold the reset button located on the control panel (example shown on the right) for 1 second to move to the OFF mode.

The Pro Model uses a timer to regulate how long a pump cycle runs and the length of time the pump rests between cycles.

NOTE:

• A blinking number on the display indicates the G3 is in SETUP MODE.

• In RUN MODE numbers on the display do not blink.

• After 60 seconds of no activity, the device returns to RUN MODE in the OFF Time cycle and the OFF

Time restarts counting down the total programmed amount of time. It does not resume the countdown from the point where the cycle was interrupted when you entered SETUP MODE.

Entering Setup Mode

Press both the UP and DOWN

ARROW buttons together for 3 seconds to enter the SETUP

MODE.

NOTE: If the lock LED is lit after entering Setup

Mode and four 0000’s are displayed, the unit has a PIN Code lock out enabled. See Entering a

PIN Code to Access

Setup Mode for instruc tions on entering a value.

Entering a PIN Code to Access Setup Mode

The G3 controller does not require a user to provide a

PIN code to access the programming features of the unit. However, Graco understands that some users may want to protect the program settings and therefore, an option for adding PIN Code authorization is available.

The instructions for setting a PIN Code are provided in the Advanced Programming section of this manual. See

page 31.

To enter the PIN Code:

1. Press both the UP and

DOWN ARROW buttons for 3 seconds.

2. The LED next to the LOCK ICON on the display lights and the 4 zeros appear on the display indicating the system requires a PIN Code entry to access the G3 in SETUP MODE.

3. The cursor is automatically positioned to enter the first character of the PIN Code.

Use the UP and DOWN

ARROW buttons to move up and down through the numbers 0-9 until the first number in the PIN code is displayed in the field.

4. Press the ENTER button to set the number. The cursor automatically moves to the next number field.

5. Repeat steps 3 and 4 for each PIN Code prompt field.

If the PIN Code you entered is correct, the first editable character on the display will flash.

NOTE: A blinking field on the display indicates the G3 is in SETUP MODE. In RUN MODE numbers on the dis play will not blink.

ON Time

• The LED next to the clock in the ON field lights, indicating you are setting the ON Time parameters.

• ON Time is set in Minutes and Seconds (MM: SS).

332298H 27

Pro Model Setup

• An LED flashes under either MM when pro gramming minutes

OR SS when pro gramming seconds.

OR

• In SETUP MODE, the number displayed in the first field, on the left side of display blinks, indicating the device is ready to pro gram the ON Time minutes.

• The total amount of ON Time cannot exceed 30 minutes. If a value greater than 30 minutes is entered, the RED alarm LED lights and the value must be updated.

If this time does not meet the application needs, contact Graco Customer Support.

Programming ON Time

NOTE: When programming a time of less than 10 min utes you must program a leading zero in the first num ber field and press the ENTER button to save the zero selection.

1. To set the ON Time use the

UP or DOWN ARROW button to scroll through numerals 0 to 5 until the desired number appears in the first MM (min utes) field.

2. Press the ENTER button to lock in the selection. The next MM number field to the right flashes indicating it is ready for programming.

3. Use the UP or DOWN

ARROW button to scroll through numerals 0 to 9 until the desired number appears in the second MM number field.

4. Press the ENTER button to lock in the selection.

The next number field to the right flashes and the LED lights under SS; indicating it is ready to program the seconds fields.

5. Repeat steps 1 - 4 to set the SS (seconds) fields.

6. After pressing the ENTER button to set the last SS field, all the programmed ON

Time information is saved.

The G3 automatically switches to the OFF Time

SETUP MODE.

OFF Time

• The LED next to the clock in the OFF field lights, indicating you are setting the OFF Time parameters.

• OFF Time is set in Hours and Minutes

(HH: MM).

• An LED flashes under either HH when pro gramming hours OR

MM when program ming minutes.

OR

• In SETUP MODE the number displayed in the first field, on the left side of display blinks, indicating the device is ready to pro gram the OFF Time hours.

• The total amount of OFF Time must be at least twice as long as the pro grammed ON Time. If a value less than twice the ON Time is entered, the RED alarm LED lights and the value must be updated.

If this time does not meet the application needs, contact Graco Customer Support.

Programming OFF Time

NOTE: When programming a time of less than 10 hours you must program a leading zero in the first number field and press the ENTER button to save the zero selection.

1. To set the OFF Time use the

UP or DOWN ARROW button to scroll through numerals 0 to 9 until the desired number appears in the first HH (hour) field.

28 332298H

Pro Model Setup

2. Press the ENTER button to lock in the selection. The next HH number field to the right flashes indicating it is ready for programming.

3. Use the UP or DOWN

ARROW button to scroll through numerals 0 to 9 until the desired number appears in the second HH number field.

4. Press the ENTER button to lock in the selection.

The next number field to the right flashes and the LED lights under MM; indicating it is ready to program the minutes fields.

5. Repeat steps 1 - 4 to set the next MM (minutes) fields.

6. After pressing the ENTER button to set the last MM field, the OFF Time informa tion is saved.

Prelube

The Prelube function determines operation of the pump when power is applied. It can be set to OFF or ON.

OFF (default) - The unit resumes its lubrication cycle at the point it was at when power was removed.

ON - The unit begins a pump cycle.

Setting Prelube

1. After you set the OFF Time information and press the ENTER button, the G3 automatically switches to the Prelube setup.

Notice the LED next to the prelube icon on the G3 display lights indicat ing you are now in the Prelube setup mode.

2. OFF displays. If you want the prelube cycle to begin imme diately, leave this set to OFF.

3. Press the ENTER button to set the selection.

4. If you want to set a prelube delay time, press the DOWN

ARROW button to change OFF to ON on the display.

Prelube Delay

Prelube Delay can be entered to delay the start of the pump’s cycle on power up. If prelube is set to ON, a prelube delay time in MM:SS must be entered. By default, the delay is set to 0 (begin an ON cycle immedi ately).

Delaying the prelube function may be desired if other critical functions or systems of your machine or vehicle are also coming on line during power up.

1. Prelube Delay is set in

MM:SS (minutes and sec onds). To set the time use the

UP or DOWN ARROW button to scroll through numerals 0 to 5 until the desired number appears in the first MM (minutes) field.

The maximum length of time Prelube Delay can be set to is 59:59 (59 minutes:59 seconds).

2. Press the ENTER button to lock in the selection. The next MM number field to the right flashes indicating it is ready for programming.

3. Use the UP or DOWN

ARROW button to scroll through numerals 0 to 9 until the desired number appears in the second MM number field.

4. Press the ENTER button to lock in the selection.

The next number field to the right flashes and the LED lights under SS; indicating it is ready to program the seconds fields.

5. Repeat steps 1 - 4 to set the SS (seconds) fields.

6. After pressing the ENTER button to set the last SS field the G3 automatically switches to the RUN MODE.

332298H 29

Advanced Programming

Advanced Programming

There are several Advanced Programming options. The following Table identifies each option and when it is used.

Advanced

Option

A1

A2

A5

Setting

Lockout

Code (Optional)

Low Level Alarm

Time

Active Alarm

Format/ Description

Secures setup modes with

PIN

MM:SS (minutes:seconds) sets amount of time between Low Level Warning to Low Level Fault.

Default = 3 minutes

Changes alarm output behavior.

Why Use This?

Prevents unauthorized users to adjusting settings.

To accommodate most lubrication situations, a con servative amount of time is programmed between the low level warning and fault to help protect unit from running dry. If necessary the amount of time the unit runs before stopping due to a low level fault can be adjusted.

Uses alarm output to determine if a unit has an alarm AND/OR loses power.

Default = OFF The output turns ON when power is applied. It turns

OFF when power is lost or an alarm occurs.

Normal operation (OFF) will only activate alarm out put in an alarm condition when power is on.

Can change (set to ON) to activate alarm with power

ON and deactivate with power OFF OR warning.

A7 Constant Alarm

Output on Fault

Changes alarm output behavior.

Used to manage power outage.

This function changes the behavior of the alarm out put in a fault from either toggling once every second or steady on.

Default = OFF

Firmware 6.02 and later

A8 4 Digit Hour Off

Time

Changes maximum OFF time.

This function changes OFF time from HH:MM to

HHHH. It allows a maximum of 9999 hours of OFF time.

Default = OFF

Firmware 6.04 and later for non-DMS models and 07.07 and later for DMS models

A10 Low Level Reset

Upon power ON

Changes low level fault upon power ON.

This function changes the behavior of the low level fault upon power ON.

A11

A12

A13

Warning OFF through alarm relay

Prelube

Sequences

Default = OFF

Changes alarm output behavior.

Default = OFF

Firmware 6.06 and later for non-DMS models and 07.09 and later for DMS models

Changes the number of the

Prelube sequences.

MM:SS Off Time Changes the OFF time pro gramming from HH:MM to

MM:SS

-

This function changes the behavior of the alarm out put in a warning condition to always OFF.

This function changes the behavior of the prelube function to add more lubrication sequences upon pump start up.

This function changes the programming of the OFF time.

-

Default = OFF

30 332298H

Advanced Programming

Entering a PIN Code for the First Time

A1-Setting Up PIN Code

A PIN Code can be programmed into the G3 to protect the settings from inadvertently being changed by unau thorized users.

1. Press the UP ARROW button for 10 seconds.

The LED next to the LOCK ICON on the display lights, indicating you have entered the PIN Mode.

2. The word OFF appears in the display. Press the UP or

DOWN ARROW button to change this to ON.

3. Press the ENTER button to enter the

PIN Code.

4. The cursor automatically is positioned to entered the first character of the PIN Code.

Use the UP and DOWN

ARROW buttons to move up and down through the numbers 0-9 until the first number in the PIN code is displayed in the field.

5. Press the ENTER button to set the number. The cursor automatically moves to the next number field.

1. The cursor is automatically positioned to enter the first character of the PIN Code.

Use the UP and DOWN

ARROW buttons to move up and down through the numbers 0-9 until the first number in the PIN code is displayed in the field.

2. Press the ENTER button to set the number. The cursor automatically moves to the next number field.

3. Repeat steps 1 and 2 for each PIN Code prompt

field.

If the PIN Code you entered is correct, the first editable character on the display will flash.

Selecting Advanced Setup Options

1. Press the UP or DOWN

ARROW button to move up or down through Advanced

Options A1 and A2.

2. Press the ENTER button to set the selection.

A2 - Low Level Alarm Time

Pump ON mode only.

Programs the amount of time in MM: SS (minutes and seconds) the pump can run between a Low Level Warn ing and a Low Level Fault to help protect unit from run ning dry.

The maximum recommended length of time is 3:00 minutes.

6. Repeat steps 4 and 5 for each PIN Code prompt field.

7. Press the ENTER button to save the

PIN Code and exit Advanced Setup.

Entering Advanced Setup

Press the UP ARROW button for 10 sec onds.

If the G3 was previously set up to require a

PIN Code, the LED next to the LOCK ICON lights, indi cating a PIN Code is required.

332298H 31

Advanced Programming

Fault, and Low Level LED illuminate.

HH MM SS ##

ON

MM : SS

OFF

HH : MM

!

flashes and the LED lights under SS; indicating it is ready to program the seconds fields.

5. Repeat steps 1 - 4 to set the SS (seconds) fields.

6. After pressing the ENTER button to set the last SS field, all the programmed ON

Time information is saved.

Unit exits Advanced Programming.

A5 - Active Alarm

Changes the alarm output behavior. Uses output to determine if a fault has occurred.

Fault and ON LED’s illuminate.

F IG . 25

NOTE: When programming a time of less than 10 min utes you must program a leading zero in the first num ber field and press the ENTER button to save the zero selection.

1. To set the time use the UP or

DOWN ARROW button to scroll through numerals 0 to

9 until the desired number appears in the first MM (min utes) field.

2. Press the ENTER button to lock in the selection. The next MM number field to the right flashes indicating it is ready for programming.

3. Use the UP or DOWN

ARROW button to scroll through numerals 0 to 9 until the desired number appears in the second MM number field.

4. Press the ENTER button to lock in the selection.

The next number field to the right

F IG . 26

1. The default OFF dis plays.

2. Press the UP or DOWN

ARROW button to change

OFF to ON on the display to activate alarm condition.

32 332298H

Advanced Programming

3. Press the ENTER button to exit

Advanced Programming.

A7- Constant Alarm Output ON Fault

This function changes the behavior of the alarm output in a fault from either toggling once every second

(default) or steady on.

Fault and Warning LEDs Illuminate

A8 - 4 Digit Hour OFF Time

Changes the OFF time from HH:MM to HHHH. Allows for a maximum of 9999 hours of OFF time.

OFF LED illuminates.

HH MM SS ##

!

ON

MM : SS

OFF

HH : MM

C

P

1

C

P

2

C

C

P

3 P

1 2 3

F IG . 28

1. The default OFF dis plays.

F IG . 27

1. The default OFF is displayed. The alarm output will toggle once a second.

2. Press the UP or DOWN

ARROW button to change

OFF to ON on the display to activate alarm condition.

3. Press the ENTER button to exit

Advanced Programming.

2. Press the UP or DOWN

ARROW to change OFF to

ON on the display to change the alarm output to be on steady

3. Press the ENTER button to exit

Advanced Programming.

332298H 33

Advanced Programming

Models with Firmware 6.03 and later. DMS Models with

Firmware 7.07 and later.

A10 - Low Level Reset Upon Power On.

This function changes the behavior of the low level upon pump power on. When A10 is on, a low level fault clears when the pump power is cycled. The pump will revolve 5 revolu tions, checking to see if the low level condition is still present.

If not, it will self clear and continue. If a low level condition exists during the 5 revolutions, it will go into a low level fault.

Low Level ON LED illuminates (F IG . 29).

A11- Warning Off Through Alarm Relay

This function changes the behavior of the alarm output in a warning condition to always off.

Fault and Warning LEDs Illuminate

F IG . 29

1. The default OFF is displayed.

The alarm output will toggle once a second.

2. Press the UP or DOWN

ARROW button to change OFF to ON on the display to change the low level reset upon power on.

3.

Press the ENTER button.

34

F

IG

. 30

1.

The default OFF is dis played. The alarm out put will turn on during a warning condition.

2.

Press the UP or DOWN ARROW to change OFF to ON on the dis play to change the alarm output to be off during a warning condi tion.

3. Press the ENTER button to exit Advanced

Programming.

332298H

Advanced Programming

Models with Firmware 6.06 and later for non-DMS models.

Models with Firmware 7.09 and later for DMS models

A12 - Prelube Sequences

This function changes the behavior of the prelube function to add more lubrication sequences upon pump start up. While running multiple sequences, after the initial sequence, PL:xx will be displayed showing how many sequences are left.

Note: if pump has option “08” and using a pressure switch with multiple sequences, a vent delay time must be pro grammed under Advanced Programming Option A3.

Prelube LED illuminates (F IG . 29)

3. Press the ENTER button to exit Advanced

Programming after the last digit of the pre lube sequence is displayed.

A13- MM:SS OFF Time

This function changes the programming of the OFF Time.

OFF and Warning LEDs Illuminate

F IG . 32

F IG . 31

1. The default 0001 is displayed.

When Prelube is on, it will run one sequence.

2.

Press the UP or DOWN ARROW button until desired number of prelube sequences displays.

NOTE: When prelube is on, and the pump is pow ered-up, the pump will run this amount of lubrication ON sequences.

1.

The default OFF is dis played. OFF/Backup time in setup mode is displayed in HH:MM

(Hours/Minutes).

2.

Press the UP or DOWN ARROW to change OFF to ON on the dis play. The OFF/Backup Time in setup mode will be displayed in

MM:SS (Minutes/Seconds).

3. Press the ENTER button to exit Advanced

Programming.

332298H 35

Run Mode

Run Mode

Time Control

After setup is complete, the G3 automatically begins to run the OFF Time sequence (F

IG

. 33).

• The G3 runs the programmed OFF sequence.

(Notice the OFF Time LED on the display lights and the OFF Time counts down on the display.)

• The example shown in F

IG

. 33 shows an OFF Time of 1 hour and 32 minutes before the lubrication cycle begins.

• When the OFF Time count reaches zero, the G3

Automatic Lubrication Pump turns the pump on and it runs for the programmed ON Time cycle (F

IG

.

34).

(Notice the ON Time LED is now illuminated on the display.)

• The example shown in F

IG

. 34 shows an ON Time of 8 minutes and 42 seconds before the lubrication cycle ends.

HH MM SS ##

!

ON

MM : SS

OFF

HH : MM HH MM SS ##

!

ON

MM : SS

OFF

HH : MM

F IG . 33

F IG . 34

• When the ON Time count reaches zero, the pump shuts off again and the system again runs OFF

Time cycle and the OFF Time LED is now again illu minated (F IG . 33).

This sequence repeats itself until the device is reprogrammed or an alarm occurs.

Manual Run Cycle

To run an extra (non-programmed) lubrica tion cycle, push the Manual Start button.

36 332298H

Run Mode

Additional Controls

Prelube / Prelube Delay

In all models a power OFF/ON cycle can be controlled with the Prelube and Prelube Delay functions.

Prelube

The Prelube function has been selected. Prelube delay is set to 00:00:

• Power to the unit cycles OFF then ON.

• Unit immediately begins a lubrication cycle.

• Pro Model - display shows ON Time (See Time

Control, page 36).

Prelube Delay

The Prelube function has been selected. Prelube delay is set to something other than 00:00:

• Power to the unit cycles OFF then ON.

• Unit immediately begins the Prelube Delay count down until the lubrication cycle begins.

• The LED next to the clock in the OFF field is illuminated (F

IG

. 35).

• The Prelube LED lights (F

IG

. 35).

• The display shows time remaining until lubrica tion cycle begins. The example shown in F

IG

.

35 shows 8 minutes and 14 seconds left until a lubrication cycle begins.

F IG . 35

HH MM SS

ON

MM : SS

##

OFF

HH : MM

!

Manual Run Cycle

To run an extra (non-programmed) lubrica tion cycle, push the Manual Start button.

NOTE: Manual Run option is not available while unit is in Vent Mode.

332298H 37

Alarms

Alarms

Any time a Fault / Warning occurs, a combination of LED’s will illuminate to notify you there is a problem and help identify the kind of Fault / Warning has occurred.

• Faults will not automatically clear. Warnings will clear after a set time, if condition was fixed.

• To clear an fault, press and hold the RESET button on the display button pad for 3 seconds.

• To clear a warning instantly press and immediately release the RESET button.

Fault / Warning Scenarios

The following pages describe the most likely fault / warnings you could receive.

Alarm Type

Low Level

Warning

What it Looks Like

HH MM SS ##

ON

MM : SS

OFF

HH : MM

!

What it Indicates

Level of lubricant in reservoir is low and addi tional lubricant needs to be added.

Unit continues to operate as normal for a limited period of time until a low level alarm is triggered.

Solution

Add lubricant to reservoir.

After lubricant is added, press the

RESET but ton to clear the warning.

Low Level

Fault

38

HH MM SS ##

!

ON

MM : SS

OFF

HH : MM

Level of lubricant in reservoir is low and addi tional lubricant needs to be added.

Unit stops pumping and displays amount of accu mulated time since the alarm was triggered.

-

Add lubricant to reservoir.

After lubri cant is

added press and hold the

RESET button to clear fault.

If repriming pump is required, the low level alarm time should be decreased. See A-2:

Advanced Programming,

Low Level Alarm Time

page 31.

332298H

Troubleshooting

Troubleshooting

Problem

Unit does not power on

Cause

Incorrect/loose wiring

Solution

Refer to Installation instructions, page

8.

Unit does not power on (DC models only)

Tripped external fuse due to internal component failure

Tripped external fuse due to pumping non-cold weather lubricant in cold weather -13°F (-25°C)

Contact Graco Customer Service.

Replace lubricant with pumpable lubri cant, rated for environmental condi tions and application.

Replace fuse.

Unit does not power on (AC models only)

Can’t set desired ON/OFF times

Unit is not operating based on the time that was programmed

Lubricant leaks past seal located on the bottom of the reservoir

Tripped internal power supply fuse due to power supply failure

Maximum duty cycle is 33% (2 min utes OFF for each minute ON)

Time entered was misinterpreted as

MM:SS instead of HH:MM (or visa versa)

Reservoir retaining tabs are cracked or broken

Reservoir is being pressurized during filling

Contact Graco Customer Service.

Adhere to allowable duty cycle. Con tact Graco Customer Support if other duty cycles are required for applica tion.

-

Verify the unit was programmed as intended, referencing programming instructions. Note the dot designation for hours, minutes, seconds on the top row of the display.

Replace reservoir.

Ensure vent hole is not plugged.

If problem persists, contact Graco

Customer Service or your local Graco distributor for assistance.

Replace unit.

Unit not pumping during ON cycle, but controller lights and functions

Failed motor

Follower plate is not going down

Air is trapped in the reservoir between the follower plate and lubricant

Pump takes several minutes before it begins pumping at the highest pump volume setting (no stroke adjust spac ers installed)

-

Pumping non-cold weather lubricant in cold weather -13°F (-25°C)

Add grease following Loading Grease

instructions, page 18. Ensure air is

purged.

Add 1 stroke adjust spacer and adjust lube cycle time to accommodate the difference in pump volume per stroke.

Dim display, unit is not operating

Tripped internal, resettable fuse due to internal component failure or sensor short circuit condition

Verify sensor and manual run inputs have not created a short circuit condi tion. Cycle power.

332298H 39

Maintenance

Maintenance

Frequency

Daily and at refill

Daily

Daily

Monthly

Zerk Fittings

Component

G3 Pump Unit and Reservoir

Display

External Wiring Harness

Required Maintenance

Keep all fittings clean using a clean dry cloth. Dirt and/or debris can damage pump and/or lubrication system.

Keep pump unit and reservoir clean using a clean dry cloth.

Keep display clean using a clean dry cloth.

Verify external harnesses are secure.

40 332298H

Parts - 2 Liter Models

Parts - 2 Liter Models

Follower Plate Models

43

44

42

41

40a

12

13

31

3 37

21

332298H

34

30

2 4 3

35

40b

Low Level Grease Models

45

57

27 1

16

36

15

14

15

60

23

18

Low Level Oil Models Only

67

1

66

17 3

33

1

2

3

Torque to 4 in. lbs (0.45 N.m)

Torque to 30 in. lbs (3.4 N.m)

Torque to 50 in. lbs (5.6 N.m)

41

Parts - 4 Liter and Larger Models

Parts - 4 Liter and Larger Models

Follower Plate Models

43

44

40a

41

42

Auto-Fill Shut Off Models

82

83

85

81

84

40c

42

36

89

45

74

87

88

62

13

31

3 37

21

73

72

34

30

40b 4L Top Fill Reservoir

75

36

61

56

Low Level Grease Models Only

45

35

57

27 1

16

14

12

1

18

15

60 23

Low Level Oil Models

67

4 2

66

33

3

17 3

1

2

3

Torque to 4 in. lbs (0.45 N.m)

Torque to 30 in. lbs (3.4 N.m)

Torque to 50 in. lbs (5.6 N.m)

332298H

Parts

Parts

36

37

40a

17

18

21

23 ❖

27

30

‡ ✺

31

33 ▲

34

13

14

15

1

3

4

Ref Part Description

BASE, three pump housing

278142 COVER, bottom, with seal

115477 SCREW, mach, torx pan hd

12

16

278144 PLATE, ricer

120822 BEARING, ball

PADDLE, stirring, 2 Liter models and larger without follower plate, included in Kit 571046

PADDLE, stirring, 4 Liter and Larger models without follower plate

PADDLE, stirring, 2 Liter models and larger without follower plate, included in Kit 571047

PADDLE, stirring, 4Liter models with follower plate

PUMP, element, included in Kit

571041

34

278145 PLUG, pump, 3/4-16

278942 PADDLE, low level models

123025 SCREW, M6

258760 BOARD, circuit, Pro

119228 SCREW, machine, flat head

16A579 LABEL, safety

16A578 LABEL, overlay

WIPER, stirring, models without fol lower plate, included in Kits 571044,

571046, and 571047

LABEL, brand

Qty

1

1

9

1

1

1

1

1

2

1

1

1

1

1

1

1

2

2

1

1

1

2

1

1

42

43

44

56

57

58 ▲

60

62

66

67

72

73

Ref Part

40b

40a

40b

40c

41

45†

61

Description

1

1

17F484 RESERVOIR, 4 Liter, G3 AFSO 1

278139 SEAL, follower plate, 2 Liter models 1

16F472 SEAL, follower plate, 4 Liter models 2

PLATE, follower

ROD, follower plate

SPRING, compression

24D838 BAFFLE, low level, 2 Liter models

24E246 BAFFLE, low level, 4 Liter models

1

1

1

1

1

24F836 BAFFLE, low level, 8 Liter models

24F923 BAFFLE, low level, 12 Liter models

24F924 BAFFLE, low level, 16 Liter models

127144 SEAL, oval

117156 BEARING, sleeve

196548 LABEL 1

16D984 WASHER, low level models

RESERVOIR, mid-section kit, with o-ring

(see quantity by size / model below)

8 Liter models

2

1

25C764

2 Liter models 2

16 Liter 3

1

1

1

1

1

1

126417 NUT, oil

24N806 FLOAT, oil

PLATE, baffle, low level

SCREW, machine

1

2

Qty

1

332298H 43

Parts

Ref Part Description Qty

82

83

84

85

87

74

75

81

SPRING, plate, valve, reset

15H108 LABEL, safety, pinch 1

VALVE, AFSO

BOLT, mounting

PACKING, o-ring

PACKING, o-ring

SEAL, upper, reservoir

SEAL, lower, reservoir

88

89

200

201

SPACER, seal, base

PLATE, valve

127783

127780

124333

CABLE,15 ft (4.5 m), SOOW w/7pos,

3 pin, 90 deg (See Wiring Diagram,

page 15)

CABLE, 15 ft (4.5 m), SOOW w/7 pos,

5 pin, 90 deg, (See Wiring Diagram,

page 16)

CABLE, 20 ft (6.1 m), SOOW, w/7 pos, 5 pin, 90 deg, (See Wiring Dia 127781

127782

16U790 CABLE, DIN, bare, (See Wiring Dia

CABLE, M12, 16.5 ft. (5 m), 4 wire,

-

124300

gram, page 16)

CABLE, 30 ft (9.1m) SOOW, w/7 pos,

5 pin, 90 deg, (See Wiring Diagram,

page 16)

straight male to flying leads (See Wir -

ing Diagram, page 15)

CABLE, M12, 6.5 ft. (5 m), 4 wire, straight male to female (See Wiring

Diagram, page 15)

1

1

202

124594

124595

4 Pin

CONNECTOR, straight, M12 male, 4

Pin

(see wiring diagram, page 16)

CONNECTOR, straight, M12 male, 5

Pin

(see wiring diagram, page 16)

Replacement Danger and Warning labels, tags and cards are available at no cost.

Also order Ref 27, Part No. 123025 and Ref 60, Part No.

16D984

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

‡ ✺ For Pro Models Only - Also order Ref 31, Part No. 119228 and Ref 34, Part No. 16A578

† Also order Ref. 57, Part No. 117156 when ordering this part.

Installation and Repair Kits

Kit No.

Description

571026 KIT, output union, 3 pump

571063 KIT, output union, 2 pump

Manual

Number

3A0523 includes pressure relief valve 16C807

571030 KIT, remote manual run, 12 volt DC

571031 KIT, remote manual run, 24 volt DC

3A0525

3A0528 with cable

571036 KIT, cover with “G” label NA

3A0533

571069

571044

571045

571046

571047

Ref 13, 36, 40

KIT, repair, 2 liter reservoir, for models with follower plate, includes Ref 13,

36, 40

KIT, replacement, paddle, 2 liter, for models without follower plate, includes Ref 13, 16, 35, 57

KIT, replacement, paddle, 2 liter, for models with follower plate, includes

Ref 13, 16, 35,40a, 42, 57

KIT, replacement, paddle, 4-16 liter, for models without follower plate, includes Ref 13, 16, 35, 57

KIT, replacement, paddle, 4 liter, for models with follower plate, includes

Ref 13, 16, 35, 57

571058 KIT, output adapter, NPT

571070 KIT, output, adapter, BSPP

571060 KIT, fill, zerk, leakproof els, includes Ref 13, 36, 40b

els, includes Ref 13, 36, 40b

-

3A0534

3A0535

3A0522

NA

3A0534

44 332298H

Parts

Pressure Relief Valves

Important Information regarding Pressure Relief

Valve 16C807.

Pressure Relief Valve 16C807 can only be used on the G3, G1, or G-Mini Pumps.

It is not intended for use with any other products.

The pressure relief valve uses a pressure adjustment screw (a) to set the pressure release point. It is not intended as a way to relieve pressure during normal operation, but as a protective measure in the event there is an unintended pressure increase in the system. Do not use this pres sure relief valve a means of relieving pressure in day-to-day, normal cycle operation. a b ti15644

The pressure adjustment screw may require periodic adjust a = adjustment screw b = locking nut ments. Whenever the valve is set/adjusted (after the set point is found) it is important to ensure that the valve is not bottomed out and there is at least 1/2 turn of adjustment remaining. This is determined by turning the screw (a) 1/2 turn and then back turning it out again.

NOTE: Turning adjustment screw (a) clockwise increases pressure.

NOTE: Each pressure relief valve requires banjo kit p/n

571058. (Except 16C807 because the banjo is already included in kit 571028.)

Part

16C807 ◆

Description

VALVE, pressure relief, 500-3500 psi (3.44

MPa, 34.4 bar - 24.1 MPa, 241 bar), Set pressure 3000 psi + 10% (20.68 MPa,

206.8 bar + 10%) Included in Kit 571028,

571071

Qty

1

1

1

1

1

1

1

Fuses

Part Description

571039 FUSE, 7.5 A for 12 volt DC

571040 FUSE, 4A for 24 volt DC

Qty

1

1

Reservoir Conversion Kits

Kit No.

Description

571155 KIT, reservoir conversion, 4 Liter

571156 KIT, reservoir conversion, 8 Liter

571157 KIT, reservoir conversion, 12 Liter

571158 KIT, reservoir conversion, 16 Liter

571229 KIT, reservoir conversion, 4L Top

Fill

Manual

Number

3A1260

3A8295

332298H 45

Parts

Mount Pattern

(For correct mounting configuration, choose either Option 1 or Option 2). See P/N 126916 template.

Option 1

0.

3 67inch

9.

3 mm

7.087 inch

1 80.0 mm

2 x Ø 0.

3 66 inch

9.

3 mm

1 .

1 80 inch

3 0.0 mm

3 .

2 68 inch

8 3 .0 mm

Option 2

2 x Ø 0.

3 66 inch

9.

3 mm

0.7

22 inch

1 8.

3 mm

3 .544 inch

90.0 mm

6.

3 78 inch

1 6 2 .0 mm

0.708 inch

1 8.0 mm

3 .740 inch

95.0 mm

3 .

1 89 inch

8 1 .0 mm

F IG . 36

46 332298H

Technical Specifications

Technical Specifications

G3 Pro Automatic Lubrication Pump

US

Pump output pressure

Fill inlet pressure

Power

100 - 240 VAC

5100 psi

5000 psi

Metric

35.1 MPa, 351.6 bar

34.4 MPa, 344.7 bar

88 - 264 VAC; 0.8 A current, 90 VA Power, 47/63 Hz, Single phase, inrush/locked rotor, max 40 A (1ms)

12 VDC

24 VDC

Fluid

Grease Models

Oil Models

Pumps

Pump Output

9 - 16 VDC; 5A current, 60 W, inrush/locked rotor 12 A

18 - 32 VDC; 2.5 A current, 60 W, inrush/locked rotor 6 A

Grease NLGI #000 - #2

At least 40 cSt. oil

Up to 3

0.12 in.

3 (2 cm 3 ) / minute per outlet - 2 spacers

0.18 in.

3 (3 cm 3 ) / minute per outlet - 1 spacer

0.25 in.

3 (4 cm 3 ) / minute per outlet - 0 spacers

Pump Outlet

Reservoir Size

1/4 -18 NPSF. Mates with 1/4 - 18 NPT male fittings

2, 4, 8, 13, 16 Liters

IP Rating

Sensor Inputs

IP69K

3 (any of pressure or cycle)

1 (machine count)

Ambient Temperatures

-40°F to 158°F -40°C to 70°C

Noise (dBa)

Maximum sound pressure

Materials of Construction

Wetted Parts

<70dBa nylon 6/6 (PA), amorphous polyamide, zinc plated steel, carbon steel, alloy steel, stainless steel, nitrile rub ber (buna-N), bronze, nickel plated alnico, chemically lubricated acetal, aluminum, PTFE

All trademarks or registered trademarks are the property of their respective owners.

Pump Maximum Weight lb (kg)

Model

2L

4L

8L

12L

16L

With follower plate

12.4 (5.6)

15.3 (6.9)

16.8 (7.6)

18.4 (8.3)

19.9 (9.0)

Without follower plate

11.4 (5.2)

13.1 (5.9)

14.6 (6.6)

16.1 (7.3)

17.6 (8.0)

With auto-fill shut off

N/A

17.9 (8.1)

19.7 (8.9)

21.6 (9.8)

23.4 (10.6)

California Proposition 65

WARNING: This product can expose you to chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65warnings.ca.gov.

332298H 47

Graco Standard Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by

Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT

LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE .

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy

(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT

MANUFACTURED BY GRACO . These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés,

à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.

Graco Information

For the latest information about Graco products, visit www.graco.com

.

For patent information, see www.graco.com/patents

.

TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.

Phone: 612-623-6928 or Toll Free: 1-800-533-9655, Fax: 612-378-3590

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

Original instructions. This manual contains English. MM 332298

Graco Headquarters: Minneapolis

International Offices: Belgium, China, Japan, Korea

GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA

Copyright 2013, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.

www.graco.com

Revision H, August 2021

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals