Digital Projector User Manual MS513/MX514/MW516

Digital Projector User Manual MS513/MX514/MW516
MS513/MX514/MW516
Digital Projector
User Manual
http://www.pureglare.com.au
Table of contents
Important safety
instructions ................... 3
Introduction.................. 7
Projector features.....................................7
Shipping contents ......................................8
Projector exterior view...........................9
Positioning your
projector ..................... 15
Choosing a location................................15
Obtaining a preferred projected image
size..............................................................16
Connection ................. 19
Connecting a computer or monitor...20
Connecting Video source devices.......21
Operation ................... 25
Personalizing the projector menu display
.................................................................... 45
Select the lamp saver mode ................. 45
Shutting down the projector ............... 46
Menu operation ...................................... 47
Maintenance ............... 59
Care of the projector............................ 59
Lamp information ................................... 60
Troubleshooting......... 66
Specifications.............. 67
Dimensions .............................................. 68
Ceiling mount installation ..................... 68
Timing chart............................................. 69
Warranty and Copyright
information................. 72
Starting up the projector ......................25
Adjusting the projected image .............26
Using the menus......................................29
Securing the projector...........................30
Switching input signal .............................33
Magnifying and searching for details ...34
Selecting the aspect ratio ......................34
Optimizing the image .............................36
Creating your own startup screen......39
Setting the presentation timer.............40
Remote paging operations ....................41
Hiding the image......................................42
Freezing the image ..................................42
Operating in a high altitude environment
.....................................................................43
Adjusting the sound................................43
Use Teaching Template .........................44
2
Table of contents
http://www.pureglare.com.au
Important safety instructions
Your projector is designed and tested to meet the latest standards for safety of information
technology equipment. However, to ensure safe use of this product, it is important that
you follow the instructions mentioned in this manual and marked on the product.
Safety Instructions
1.
Please read this manual before
you operate your projector. Save
it for future reference.
2.
Do not look straight at the
projector lens during operation.
The intense light beam may damage
your eyes.
3.
Refer servicing to qualified
service personnel.
4.
Always open the lens shutter or
remove the lens cap when the
projector lamp is on.
5.
In some countries, the line voltage is
NOT stable. This projector is
designed to operate safely within a
mains voltage between 100 to 240
volts AC, but could fail if power cuts
or surges of ±10 volts occur. In
areas where the mains voltage
may fluctuate or cut out, it is
recommended that you connect
your projector through a power
stabilizer, surge protector or
uninterruptible power supply
(UPS).
6.
Do not block the projection lens with
any objects when the projector is
under operation as this could cause
the objects to become heated and
deformed or even cause a fire.
Important safety instructions 3
http://www.pureglare.com.au
Safety Instructions (Continued)
4
7.
The lamp becomes extremely hot
during operation. Allow the
projector to cool for approximately
45 minutes prior to removing the
lamp assembly for replacement.
8.
Do not operate lamps beyond the
rated lamp life. Excessive operation
of lamps beyond the rated life could
cause them to break on rare
occasions.
9.
Never replace the lamp assembly or
any electronic components unless
the projector is unplugged.
10.
Do not place this product on an
unstable cart, stand, or table. The
product may fall, sustaining serious
damage.
11.
Do not attempt to disassemble this
projector. There are dangerous high
voltages inside which may cause
death if you should come into
contact with live parts. The only
user serviceable part is the lamp
which has its own removable cover.
Under no circumstances should you
ever undo or remove any other
covers. Refer servicing only to
suitably qualified professional
service personnel.
12.
When the projector is under
operation, you may sense some
heated air and odor from its
ventilation grill. It is a normal
phenomenon and not a product
defect.
Important safety instructions
http://www.pureglare.com.au
Safety Instructions (Continued)
13.
Do not place this projector in any of
the following environments.
14.
Do not block the ventilation holes.
- Do not place this projector on a blanket,
bedding or any other soft surface.
- Do not cover this projector with a cloth
or any other item.
- Do not place inflammables near the
projector.
- Space that is poorly ventilated or
confined. Allow at least 50 cm clearance
from walls and free flow of air around
the projector.
- Locations where temperatures may
become excessively high, such as the
inside of a car with all windows rolled up.
- Locations where excessive humidity,
dust, or cigarette smoke may
contaminate optical components,
shortening the projector's life span and
darkening the image.
15.
If the ventilation holes are seriously
obstructed, overheating inside the
projector may result in a fire.
Always place the projector on a level,
horizontal surface during operation.
- Do not use if tilted at an angle of more
than 10 degrees left to right, nor at angle
of more than 15 degrees front to back.
Using the projector when it is not fully
horizontal may cause a malfunction of, or
damage to, the lamp.
- Locations near fire alarms
- Locations with an ambient temperature
above 40°C / 104°F
- Locations where the altitudes are higher
than 3000 m (10000 feet).
3000 m
(10000 feet)
0m
(0 feet)
Important safety instructions 5
http://www.pureglare.com.au
Safety Instructions (Continued)
16.
18.
Do not stand the projector on end
vertically. Doing so may cause the
projector to fall over, causing injury or
resulting in damage to the projector.
17.
Do not step on the projector or place
any objects upon it. Besides probable
physical damage to the projector,
doing so may result in accidents and
possible injury.
19.
Do not place liquids near or on the
projector. Liquids spilled into the
projector may cause it to fail. If the
projector does become wet,
disconnect it from the power supply's
wall socket and call BenQ to have the
projector serviced.
This product is capable of displaying
inverted images for ceiling mount
installation.
Use only BenQ's Ceiling Mount Kit for
mounting the projector and ensure it is
securely installed.
6
Important safety instructions
http://www.pureglare.com.au
Introduction
Projector features
The model MS513, MX514, MW516 are projectors with the feature of high-performance
projection, power- saving and user-friendly design to deliver the user benefit of high
reliability, environment-friendly and ease of use.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Eco Blank - With Philips ImageCare® technology,the Eco Blank function will save up
to 70% of your lamp power at the same time your image is hiding.
Smart Eco mode - With Philips ImageCare® technology, lamp power consumption
will save from 30% to 100% dynamically by detecting the content brightness level when
Smart Eco mode is selected.
Instant restart - Turn on the power to have the image back immediately within a
short time after turning it off .
HDMI - Connecting a variety of audio/video components from digital signal.
Long lamp life - low ownership with up to 6500 hours lamp life.
High brightness projection - Suitable for conference meeting and classroom used.
<1W standby mode - Less than 1 W power consumption in standby mode
2W speaker - Built-in speaker providing mixed mono audio.
Multi-language - 28 languages On-Screen Display (OSD) menus
Quick auto search - speeding up the signal detecting process.
One-key auto-adjustment - Automatically determines the best picture timings for
the displayed image.
Wall color correction - Allowing projection on surfaces of several predefined colors
Color balance control - Adjustable for data/video display
3D color management - allowing color adjustments to your liking
Quick cooling - Selectable to makes the projector cool in a shorter time
Presentation timer - For better control of time during presentations
Selectable password protected function
Component HDTV compatibility (YPbPr)
•
The apparent brightness of the projected image will vary depending on the ambient lighting
conditions, selected input signal contrast/brightness settings, and is proportional to
projection distance.
•
The lamp brightness will decline over time and may vary within the lamp manufacturers
specifications. This is normal and expected behavior.
Introduction 7
http://www.pureglare.com.au
Shipping contents
Carefully unpack and verify that you have all of the items shown below. If any of these items
are missing, please contact your place of purchase.
Standard accessories
The supplied accessories will be suitable for your region, and may differ from those illustrated.
*The warranty card is only supplied in some specific regions. Please consult your dealer for
detailed information.
Projector
Power cord
VGA cable
User manual CD
Warranty card*
Digital
Quick Projector
Start
Guide
Quick start guide
Remote control with battery
Optional accessories
1.
2.
8
Spare lamp kit
Ceiling mount kit
3.
4.
5.
Carry bag
RS232 cable
Presentation plus
Introduction
http://www.pureglare.com.au
Projector exterior view
1.
Front/upper side
1
2
3
4
5
6
7
8
Rear/lower side
9 10 11 12
16 17
13 14
18 19
15
20
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
External control panel
(See "Projector" on page 10 for
details.)
Lamp cover
Zoom ring
Focus ring
Vent (heated air exhaust)
Front IR remote sensor
Projection lens
Quick-release button
USB input jack
HDMI input jack
S-Video input jack
RGB (PC)/Component video
(YPbPr/ YCbCr) signal input jack
RS-232 control port
Audio input jack
Kensington anti-theft lock slot
AC power cord inlet
Video input jack
RGB signal output jack
Audio output jack
Ceiling mount holes
Rear adjuster foot
21 8
Introduction 9
http://www.pureglare.com.au
Controls and functions
Projector
7.
1
2
3
9
4
5
10
11
7
6
7
12
8
13
8.
9
9.
1.
2.
3.
4.
5.
6.
10
Focus ring
Adjusts the focus of the projected image.
See "Fine-tuning the image size and clarity"
on page 27 for details.
Zoom ring
Adjusts the size of the image. See "Finetuning the image size and clarity" on page
27 for details.
POWER indicator light
Lights up or flashes when the projector is
under operation. See "Indicators" on page
65 for detail.
TEMP(temperature) warning light
Lights up red if the projector's
temperature becomes too high. See
"Indicators" on page 65 for details.
MENU/EXIT
Turns on the On-Screen Display (OSD)
menu. Goes back to previous OSD menu,
exits and saves menu settings.
I
I
POWER
Toggles the projector between standby
mode and on.See "Starting up the
projector" on page 25 and "Shutting down
the projector" on page 46 for details.
10.
11.
12.
13.
Volume /Arrow keys ( /
Left,
/
Right)
Adjusts the sound level.
When the On-Screen Display (OSD)
menu is activated, the #7 and #9 keys are
used as directional arrows to select the
desired menu items and to make
adjustments. See "Using the menus" on
page 29 for details.
ECO BLANK
Used to hide the screen picture. See
"Hiding the image" on page 42 for details.
Keystone/Arrow keys ( / Up,
/
Down)
Manually corrects distorted images
resulting from an angled projection. See
"Correcting keystone" on page 28 for
details.
LAMP indicator light
Indicates the status of the lamp. Lights up
or flashes when the lamp has developed a
problem. See "Indicators" on page 65 for
details.
AUTO
Automatically determines the best
picture timings for the displayed image.
See "Auto-adjusting the image" on page
26 for details.
SOURCE
Displays the source selection bar. See
"Switching input signal" on page 33 for
details.
MODE/ENTER
Selects an available picture setup mode.
See "Selecting a picture mode" on page
36 for details.
Activates the selected On-Screen Display
(OSD) menu item. See "Using the menus"
on page 29 for details.
Introduction
http://www.pureglare.com.au
Ceiling mounting the projector
We want you to have a pleasant experience using your BenQ projector, so we need
to bring this safety matter to your attention to prevent possible damage to person
and property.
If you intend to mount your projector on the ceiling, we strongly recommend that
you use a proper fitting BenQ projector ceiling mount kit and that you ensure it is
securely and safely installed.
If you use a non-BenQ brand projector ceiling mount kit, there is a safety risk that
the projector may fall from the ceiling due to an improper attachment through the
use of the wrong gauge or length screws.
You can purchase a BenQ projector ceiling mount kit from the place you purchased
your BenQ projector. BenQ recommends that you also purchase a separate
Kensington lock compatible security cable and attach it securely to both the
Kensington lock slot on the projector and the base of the ceiling mount bracket. This
will perform the secondary role of restraining the projector should its attachment to
the mounting bracket become loose.
Introduction 11
http://www.pureglare.com.au
Remote control
5.
1
11
12
2
13
3
3
4
5
14
12
6
15
7
16
17
8
18
19
9
20
10
21
22
1.
2.
3.
4.
12
Eco Blank
Press the Eco Blank button to turn off
the image for a period of time with up to
70% lamp power saving. Press again to
restore the image. See "Hiding the
image" on page 42 for details.
6.
Smart Eco
Displays the lamp mode selection
bar(Normal/Economic/Smart Eco).
7.
Aspect
Selects the display aspect ratio. See
"About the aspect ratio" on page 35 for
details.
8.
Digital Zoom keys (+, -)
Magnifies or reduces the projected
picture size. See "Magnifying and
searching for details" on page 34 for
details.
9.
Timer On
Activates or displays an on-screen timer
based on your own timer setting. See
"Setting the presentation timer" on page
40 for details.
10. Timer Setup
Enters presentation timer setting
directly. See "Setting the presentation
timer" on page 40 for details.
Info
Showing the status information of the
projector.
Menu/Exit
Turns on the On-Screen Display (OSD)
I
I Power
menu. Goes back to previous OSD menu, 11.
Toggles
the projector between standby
exits and saves menu settings.
mode
and
on. See "Starting up the
See "Using the menus" on page 29 for details.
projector" on page 25 and "Shutting
Left/ Right
down the projector" on page 46 for
When the On-Screen Display (OSD) menu
details.
is activated, the #3 and #12 keys are used
12.
Keystone/Arrow keys ( / Up,
as directional arrows to select the desired
/ Down)
menu items and to make adjustments. See
Manually corrects distorted images
"Using the menus" on page 29 for details.
resulting from an angled projection. See
Mode/Enter
"Correcting keystone" on page 28 for
Selects an available picture setup mode.
details.
See "Selecting a picture mode" on page 36
13.
Auto
for details.
Automatically determines the best
Activates the selected On-Screen
picture timings for the displayed image.
Display (OSD) menu item. See "Using the
See "Auto-adjusting the image" on page
menus" on page 29 for details.
26 for details.
Introduction
http://www.pureglare.com.au
14. Source
Displays the source selection bar. See
"Switching input signal" on page 33 for
details.
15. Volume +/Adjusts the sound level. See "Adjusting
the sound" on page 43 for details.
16. Page Up/Down
Page up/down arrows when connected
through USB to a PC. See "Remote
paging operations" on page 41 for
details.
17. Mute
Toggles projector audio between on and
off.
18.
Freeze
Freezes the projected image. See
"Freezing the image" on page 42 for
details.
19. Capture
Captures current displayed screen to be
MyScreen. See "Creating your own startup
screen" on page 39 for details.
20. Test
Displays the test pattern. See "Use build-in
test pattern" on page 27.
21. Teaching Template
Displays the selectable bar for teachers
choosing the template as his/her suitable
teaching background. See "Use Teaching
Template" on page 44.
22. CC
Display the video term description on
screen which is provided for hard-ofhearing viewers.
Infra-Red (IR) remote control sensor is located on the front of the projector. The remote
control must be held at an angle within 15 degrees perpendicular to the projector's IR
remote control sensor to function correctly. The distance between the remote control
and the sensor should not exceed 8 meters (~ 26 feet).
Make sure that there are no obstacles between the remote control and the IR sensor on
the projector that might obstruct the infra-red beam.
•
Operating the projector from the front
Appr
o
x. 15
°
Introduction 13
http://www.pureglare.com.au
Replacing the remote control battery
1.
2.
3.
To open the battery cover, turn the remote control over to view its back, push on
the finger grip on the cover and slide it up in the direction of the arrow as illustrated.
The cover will slide off.
Remove any existing batteries (if necessary) and install two AAA batteries observing
the battery polarities as indicated in the base of the battery compartment. Positive
(+) goes to positive and negative (-) goes to negative.
Refit the cover by aligning it with the base and sliding it back down into position. Stop
when it clicks into place.
14
•
Avoid excessive heat and humidity.
•
There may be battery damage if the battery is incorrectly replaced.
•
Replace only with the same or equivalent type recommended by the battery manufacturer.
•
Dispose of the used battery according to the battery manufacturer’s instructions.
•
Never throw a battery into a fire. There may be danger of an explosion.
•
If the battery is dead or if you will not be using the remote control for a long time, remove
the battery to prevent damage to the remote control from possible battery leakage.
Introduction
http://www.pureglare.com.au
Positioning your projector
Choosing a location
Your room layout or personal preference will dictate which installation location you select.
Take into consideration the size and position of your screen, the location of a suitable
power outlet, as well as the location and distance between the projector and the rest of
your equipment.
Your projector is designed to be installed in one of four possible installation locations:
1.
Front Table
Select this location with the projector placed near the
floor in front of the screen. This is the most common
way to position the projector for quick setup and
portability.
2.
Front Ceiling
Select this location with the projector suspended upsidedown from the ceiling in front of the screen.
Purchase the BenQ Projector Ceiling Mounting Kit from
your dealer to mount your projector on the ceiling.
Set Front Ceiling in the SYSTEM SETUP: Basic >
Projector Position menu after you turn the projector
on.
3.
Rear Table
Select this location with the projector placed near the
floor behind the screen.
Note that a special rear projection screen is required.
Set Rear Table in the SYSTEM SETUP: Basic >
Projector Position menu after you turn the projector
on.
4.
Rear Ceiling
Select this location with the projector suspended upsidedown from the ceiling behind the screen.
Note that a special rear projection screen and the BenQ
Projector Ceiling Mounting Kit are required for this
installation location.
Set Rear Ceiling in the SYSTEM SETUP: Basic >
Projector Position menu after you turn the projector on.
Positioning your projector 15
http://www.pureglare.com.au
Obtaining a preferred projected image size
The distance from the projector lens to the screen, the zoom setting (if available), and the
video format each factors in the projected image size.
The projector should always be placed horizontally level (like flat on a table), and
positioned directly perpendicular (90° right-angle square) to the horizontal center of the
screen. This prevents image distortion caused by angled projections (or projecting onto
angled surfaces).
If the projector is mounted on a ceiling, it must be mounted upside-down so that it
projects at a slightly downward angle.
You can see from the diagram on page 18, that this type of projection causes the bottom
edge of the projected image to be vertically offset from the horizontal plane of the
projector. When ceiling mounted, this refers to the top edge of the projected image.
If the projector is positioned further away from the screen, the projected image size
increases, and the vertical offset also increases proportionately.
When determining the position of the screen and projector, you will need to account for
both the projected image size and the vertical offset dimension, which are proportional to
the projection distance.
BenQ has provided a table of screen sizes to assist you in determining the ideal location for
your projector. There are two dimensions to consider, the perpendicular horizontal
distance from the center of the screen (projection distance), and the vertical offset height
of the projector from the horizontal edge of the screen (offset).
16
Positioning your projector
http://www.pureglare.com.au
How to determine the position of the projector
for a given screen size
1.
2.
Select your screen size.
Refer to the table on page 18 and find the closest match to your screen size in the
left columns labelled "Screen size". Using this value, look across this row to the right
to find the corresponding average distance from screen value in the column labelled
"Average". This is the projection distance.
3.
On that same row, look across to the right column and make note of the "Vertical
offset (mm)" value. This will determine the final vertical offset placement of the
projector in relation to the edge of the screen.
4.
The recommended position for the projector is aligned perpendicular to the
horizontal center of the screen, at the distance from the screen determined in step 2
above, and offset by the value determined in step 3 above.
For example, if you are using the MX514/MS513 and a 120-inch screen, the average
projection distance is 5040 mm and with a vertical offset of 274 mm. if you are using the
MW516 and a 120-inch screen, the average projection distance is 3894 mm and with a
vertical offset of 251 mm.
How to determine the recommended screen size
for a given distance
This method can be used for situations where you have purchased this projector and
would like to know what screen size will fit in your room.
The maximum screen size is limited by the physical space available in your room.
1.
Measure the distance between the projector and where you want to position the
screen. This is the projection distance.
2.
Refer to the table on page 18 and find the closest match to your measurement in the
average distance from screen column labelled "Average". Check that your measured
distance is between the min and max distances listed on either side of the average
distance value.
3.
Using this value, look across that row to the left to find the corresponding "Screen
size" listed in that row. That is the projected image size of the projector at that
projection distance.
4.
On that same row, look across to the right column and make note of the "Vertical
offset (mm)" value. This will determine the final placement of the screen in relation
to the horizontal plane of the projector.
For example, if you are using the MX514/MS513 and measured projection distance was 5.0
m (5000 mm), the closest match in the "Average" column is 5040 mm. Looking across this
row shows that a 120-inch screen is required. If you are using the MW516 and your
measured projection distance is 5.0 m (5000 mm), the closest match in the column is 3894
mm. Looking across this row shows that a 120-inch screen is required.
If you place the projector in a different position (to that recommended), you will have to
tilt it down or up to center the image on the screen. In these situations, some image
distortion will occur. Use the Keystone function to correct the distortion. See "Correcting
keystone" on page 28 on page for details.
Positioning your projector 17
http://www.pureglare.com.au
Projection dimensions
Refer to "Dimensions" on page 68 for the center of lens dimensions of this projector
before calculating the appropriate position.
Maximum zoom
Minimum zoom
Screen
Center of lens
Vertical offset
Projection distance
MX514/MS513
Screen size
Distance from screen (mm)
Vertical offDiagonal
W
H
Min length Aver- Max length set (mm)
Inch
mm (mm) (mm) (max. zoom) age (min. zoom)
30
40
50
60
80
100
120
150
200
220
250
300
762
1016
1270
1524
2032
2540
3048
3810
5080
5588
6350
7620
610
813
1016
1219
1626
2032
2438
3048
4064
4470
5080
6096
457
610
762
914
1219
1524
1829
2286
3048
3353
3810
4572
1200
1600
2000
2400
3200
4000
4800
6000
8000
8800
10000
12000
1260
1680
2100
2520
3360
4200
5040
6300
8400
9240
10500
12600
1320
1760
2200
2640
3520
4400
5280
6600
8800
9680
11000
13200
69
91
114
137
183
229
274
343
457
503
572
686
MW516
Screen size
Distance from screen (mm)
Vertical
offset
Diagonal
W
H
Min length Aver- Max length
Inch
mm (mm) (mm) (max. zoom) age (min. zoom) (mm)
30
40
50
60
80
100
120
150
200
220
250
300
762
1016
1270
1524
2032
2540
3048
3810
5080
5588
6350
7620
646
861
1077
1292
1723
2153
2584
3230
4307
4738
5384
6461
403
538
673
807
1077
1346
1615
2019
2692
2961
3365
4038
1018
1273
1564
1871
2435
3014
3594
4465
5916
6496
7367
8818
1127
1420
1731
2047
2658
3276
3894
4823
6369
6987
7916
9462
1235
1567
1897
2223
2881
3538
4194
5180
6822
7478
8464
10106
61
83
105
126
164
205
251
313
416
457
521
624
There is 3% tolerance among these numbers due to optical component variations. BenQ
recommends that if you intend to permanently install the projector, you should physically test
the projection size and distance using the actual projector in situ before you permanently install
it, so as to make allowance for this projector's optical characteristics. This will help you
determine the exact mounting position so that it best suits your installation location.
18
Positioning your projector
http://www.pureglare.com.au
Connection
When connecting a signal source to the projector, be sure to:
1.
2.
3.
Turn all equipment off before making any connections.
Use the correct signal cables for each source.
Ensure the cables are firmly inserted.
•
In the connections shown below, some cables may not be included with the projector (see
"Shipping contents" on page 8). They are commercially available from electronics stores.
•
For detailed connection methods, see pages 20-24.
3
2
1
2
4
8 7 6 5
4
1. USB Cable
5. Component Video to VGA (DSub)
adapter cable
2. VGA cable
6. S-Video cable
3. VGA to DVI-A cable
7. Video cable
4. Audio Cable
8. HDMI cable
Connection 19
http://www.pureglare.com.au
Connecting a computer or monitor
Connecting a computer
The projector can connect to both IBM® compatibles and Macintosh® computers. A Mac
adapter is needed if you are connecting legacy version Macintosh computers.
To connect the projector to a notebook or desktop computer:
1.
2.
3.
Take the supplied VGA cable and connect one end to the D-Sub output socket of the
computer.
Connect the other end of the VGA cable to the COMPUTER IN-1 or
COMPUTER IN-2 signal input jack on the projector.
If you wish to make use of the projector speaker(s) in your presentations, take a
suitable audio cable and connect one end of the cable to the audio output jack of the
computer, and the other end to the AUDIO jack of the projector. When you
connect audio output signal from a computer, please balance out the volume control
bar to obtain an optimal sound effects.
Many notebooks do not turn on their external video ports when connected to a projector.
Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a
function key labeled CRT/LCD or a function key with a monitor symbol on the notebook. Press
FN and the labeled function key simultaneously. Refer to your notebook's documentation to find
your notebook's key combination.
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the screen, you
can connect the MONITOR-OUT signal output jack on the projector to an external
monitor following the instructions below:
To connect the projector to a monitor:
1.
2.
3.
20
Connect the projector to a computer as described in "Connecting a computer" on
page 20.
Take a suitable VGA cable (only one supplied) and connect one end of the cable to
the D-Sub input jack of the video monitor.
Or if your monitor is equipped with a DVI input jack, take a VGA to DVI-A cable and
connect the DVI end of the cable to the DVI input jack of the video monitor.
Connect the other end of the cable to the MONITOR-OUT jack on the projector.
•
The output signal for MONITOR-OUT jack only works when the input signal comes from
COMPUTER IN-1 or COMPUTER IN-2 jack. When the projector is powered on, the output
signal from MONITOR-OUT jack varies depending on the input signal from COMPUTER
IN-1 or COMPUTER IN-2 jack.
•
If you wish to use this connection method when the projector is in standby mode, make sure
the Standby Monitor Out function is turned on in the SYSTEM SETUP: Advanced menu.
See "Standby Settings" on page 57 for details.
Connection
http://www.pureglare.com.au
Connecting Video source devices
You need only connect the projector to a Video source device using just one of the above
connecting methods, however each provides a different level of video quality. The method
you choose will most likely depend upon the availability of matching terminals on both the
projector and the Video source device as described below:
Terminal
name
Terminal appearance
Reference
Picture quality
HDMI
"Connecting an
HDMI source device"
on page 22
Best
HDMI
COMPUTER
Component Video
S-VIDEO
S-Video
VIDEO
"Connecting a
Component Video
source device" on
page 23
"Connecting an SVideo/composite
source device" on
page 24
Video
Better
Good
Normal
Connection 21
http://www.pureglare.com.au
Connecting an HDMI source device
The projector provides a HDMI input jack that allows you to connect it to an HDMI
source device like a DVD player, a DTV tuner or a display.
HDMI (High-Definition Multimedia Interface) supports uncompressed video data
transmission between compatible devices like DTV tuners, DVD players and displays over a
single cable. It provides pure digital viewing and listening experience.
Examine your Video source device to determine if it has a set of unused HDMI output
jacks available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an HDMI source device:
1.
2.
22
Take an HDMI cable and connect one end to the HDMI output jack of the HDMI
source device. Connect the other end of the cable to the HDMI signal input jack on
the projector. Once connected, the audio can be controlled by the projector OnScreen Display (OSD) menus. See "Audio Settings" on page 56 for details..
Connect the other end of the HDMI cable to the HDMI jack on the projector.
•
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
•
In the unlikely event that you connect the projector to a DVD player via the projector's
HDMI input and the projected picture displays wrong colors, please change the color space
to YUV. See "Changing Color Space" on page 33 for details.
Connection
http://www.pureglare.com.au
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component Video
output jacks available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a Component Video source device:
1.
2.
3.
•
Take a Component Video to VGA (D-Sub) adaptor cable and connect the end with 3
RCA type connectors to the Component Video output jacks of the Video source
device. Match the color of the plugs to the color of the jacks; green to green, blue to
blue, and red to red.
Connect the other end of the Component Video to VGA (D-Sub) adaptor cable
(with a D-Sub type connector) to the COMPUTER IN-1 or COMPUTER IN-2
jack on the projector.
If you wish to make use of the projector speaker(s) in your presentations, take a
suitable audio cable and connect one end of the cable to the audio output jack of the
device, and the other end to the AUDIO jack of the projector.
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
Connection 23
http://www.pureglare.com.au
Connecting an S-Video/composite source device
Examine your Video source device to determine if it has an unused S-Video/composite
output jack available:
•
•
•
If it has both jacks, use the S-Video output jack for connection as the S-Video terminal
provides better picture quality than the Video terminal.
If it has either of the output jack, you can also continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an S-Video/Video source device:
1.
2.
3.
•
24
Take an S-Video/Video cable and connect one end to the S-Video/Video output jack
of the Video source device.
Connect the other end of the S-Video/Video cable to theS-Video/ Video jack on
the projector.
If you wish to make use of the projector speaker(s) in your presentations, take a
suitable audio cable and connect one end of the cable to the audio output jack of the
device, and the other end to the AUDIO jack of the projector.
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
Connection
http://www.pureglare.com.au
Operation
Starting up the projector
1.
Plug the power cord into the projector and into
a power outlet. Turn on the power outlet switch
(where fitted). Check that the POWER
indicator light on the projector lights orange
after power has been applied.
•
Please use the original accessories (e.g. power cable)
only with the device to avoid possible dangers such as
electric shock and fire.
•
If Direct power on function is activated in the SYSTEM SETUP: Basic > Operation Settings
menu, the projector will turn on automatically after the power cord has been connected and
power has been applied. See "Direct Power On" on page 55 for details.
2.
Press II POWER on the projector or
remote control to start the projector. The
POWER indicator light flashes and stays
green when the projector is on.
The start up procedure takes about 30
seconds. In the later stage of start up, a
startup logo is projected.
(If necessary) Rotate the focus ring to adjust
the image clearness.
If the projector is still hot from previous activity, it will run the cooling fan for approximately 90
seconds before energizing the lamp.
3.
4.
5.
6.
If the projector is activated for the first time,
select your OSD language following the onscreen instructions.
If you are prompted for a password, press the
arrow keys to enter a six digit password. See
"Utilizing the password function" on page 30
for details.
Switch all of the connected equipment on.
The projector will start to search for input
signals. The current input signal being scanned
displays in the screen. If the projector doesn't
detect a valid signal, the message 'No Signal'
will continue displaying until an input signal is
found.
You can also press Source on the projector or remote control to select your
desired input signal. See "Switching input signal" on page 33 for details.
Operation 25
http://www.pureglare.com.au
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot.
These adjusters change the image height and projection angle. To adjust the projector:
1.
Press the quick-release button and lift the
front of the projector. Once the image is
positioned where you want it, release the
quick-release button to lock the foot in
position.
2.
Screw the rear adjuster foot to fine tune the
horizontal angle.
To retract the foot, hold up the projector while
pressing the quick-release button, then slowly
lower the projector. Screw the rear adjuster foot
in a reverse direction.
1
2
If the projector is not placed on a flat surface or the screen and the projector are not
perpendicular to each other, the projected image becomes trapezoidal. To correct this
situation, see "Magnifying and searching for details" on page 34 for details.
•
Do not look into the lens while the lamp is on. The strong light from the lamp may cause
damage to your eyes.
•
Be careful when you press the adjuster button as it is close to the exhaust vent where hot air
comes from.
Auto-adjusting the image
In some cases, you may need to optimize the
picture quality. To do this, press AUTO on the
projector or remote control. Within 3
seconds, the built-in Intelligent Auto
Adjustment function will re-adjust the values of
Frequency and Clock to provide the best
picture quality.
26
•
The screen will be blank while Auto is
functioning.
•
This function is only available when PC signal (analog RGB) is selected.
Operation
http://www.pureglare.com.au
Use build-in test pattern
You can adjust the image shape and focus
status by observing the input signal content, or
using the test pattern build-in OSD manual
from OSD or remote control for better
observe the shape changed.
Open the OSD menu and go to the SYSTEM
SETUP: Advanced > Test Pattern > On.
Press MODE/ENTER. The Test Pattern
displays.
Fine-tuning the image size and clarity
1.
Adjust the projected image to the size that
you need using the zoom ring.
2.
Then sharpen the image by rotating the
focus ring.
Operation 27
http://www.pureglare.com.au
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either
the top or bottom. It occurs when the projector is not perpendicular to the screen.
To correct this, besides adjusting the height of the projector, you will need to manually
correct it following one of these steps.
• Using the remote control
Press
/
on the projector or remote
control to display the Keystone correction page.
Press
to correct keystoning at the top of the
image. Press
to correct keystoning at the
bottom of the image.
• Using the OSD menu
1.
Press MENU/EXIT and then press
/
until the DISPLAY menu is highlighted.
2.
Press
to highlight Keystone and press
MODE/ENTER. The Keystone correction
page displays.
3.
Press
to correct keystoning at the top
of the image or press
to correct
keystoning at the bottom of the image.
28
Press
Operation
http://www.pureglare.com.au
/
.
Press
/
.
Using the menus
The projector is equipped with On-Screen Display (OSD) menus for making various
adjustments and settings.
Below is the overview of the OSD menu.
Main menu icon
Main menu
Highlight
Status
Sub-menu
Press MENU/
EXIT to the
previous page
or to exit.
Current input signal
The following example describes how to set the OSD language.
1.
Press MENU/EXIT on the projector
or remote control to turn the OSD
menu on.
3.
Press
to highlight
Language and press
/ to
select a preferred language.
2.
Use
/ to highlight the SYSTEM
SETUP: Basic menu.
4.
Press MENU/EXIT twice* on
the projector or remote
control to leave and save the
settings.
*The first press leads you back to
the main menu and the second
press closes the OSD menu.
Operation 29
http://www.pureglare.com.au
Securing the projector
Using a security cable lock
The projector has to be installed in a safe place to prevent theft. Otherwise, purchase a
lock, such as the Kensington lock, to secure the projector. You can locate a Kensington
lock slot on the rear side of the projector. See item 15 on page 9 for details.
A Kensington security cable lock is usually a combination of key(s) and the lock. Refer to
the lock's documentation for finding out how to use it.
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an
option for setting up password security. The password can be set through the On-Screen
Display (OSD) menu.
WARNING: You will be inconvenienced if you activate the power-on lock functionality and
subsequently forget the password. Print out this manual (if necessary) and write the password
you used in this manual, and keep the manual in a safe place for later recall.
Setting a password
Once a password has been set, the projector cannot be used unless the correct password is
entered every time the projector is started.
1.
2.
3.
4.
Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security
Settings menu. Press MODE/ENTER. The Security Settings page displays.
Highlight Power on lock and select On by pressing / .
As pictured to the right, the four arrow keys
( ,
, , ) respectively represent 4 digits
(1, 2, 3, 4). According to the password you
desire to set, press the arrow keys to enter six
digits for the password.
Confirm the new password by re-entering the
new password.
Once the password is set, the OSD menu
returns to the Security Settings page.
IMPORTANT: The digits being input will display as asterisks on-screen. Write your selected
password down here in this manual in advance or right after the password is entered so that it is
available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this manual in a safe place.
5.
30
To leave the OSD menu, press MENU/EXIT.
Operation
http://www.pureglare.com.au
If you forget the password
If the password function is activated, you will be asked
to enter the six-digit password every time you turn on
the projector. If you enter the wrong password, the
password error message as pictured to the right
displays lasting for three seconds, and the message
'INPUT PASSWORD' follows. You can retry by
entering another six-digit password, or if you did not
record the password in this manual, and you absolutely do not remember it, you can use
the password recall procedure. See "Entering the password recall procedure" on page 31
for details.
If you enter an incorrect password 5 times in succession, the projector will automatically
shut down in a short time.
Entering the password recall procedure
1.
2.
3.
Press and hold Auto on the projector or
remote control for 3 seconds. The projector
will display a coded number on the screen.
Write down the number and turn off your
projector.
Seek help from the local BenQ service center to
decode the number. You may be required to
provide proof of purchase documentation to
verify that you are an authorized user of the
projector.
Changing the password
1.
2.
3.
4.
Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security
Settings > Change password menu.
Press MODE/ENTER. The message 'INPUT CURRENT PASSWORD' displays.
Enter the old password.
•
If the password is correct, another message 'INPUT NEW PASSWORD'
displays.
•
If the password is incorrect, the password error message displays lasting for three
seconds, and the message 'INPUT CURRENT PASSWORD' displays for
your retry. You can press MENU/EXIT to cancel the change or try another
password.
Enter a new password.
IMPORTANT: The digits being input will display as asterisks on-screen. Write your selected
password down here in this manual in advance or right after the password is entered so that it is
available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this manual in a safe place.
5.
Confirm the new password by re-entering the new password.
Operation 31
http://www.pureglare.com.au
6.
7.
You have successfully assigned a new password
to the projector. Remember to enter the new
password next time the projector is started.
To leave the OSD menu, press MENU/EXIT.
Disabling the password function
To disable password protection, go back to the SYSTEM SETUP: Advanced >
Security Settings > Power on lock menu after opening the OSD menu system. Select
Off by pressing
/ . The message 'INPUT PASSWORD' displays. Enter the current
password.
•
If the password is correct, the OSD menu returns to the Security Settings
page with 'Off' shown in the row of Power on lock. You will not have to enter
the password next time you turn on the projector.
•
If the password is incorrect, the password error message displays lasting for three
seconds, and the message 'INPUT PASSWORD' displays for your retry. You
can press MENU/EXIT to cancel the change or try another password.
Though the password function is disabled, you need to keep the old password in hand should you
ever need to re-activate the password function by entering the old password.
32
Operation
http://www.pureglare.com.au
Switching input signal
The projector can be connected to multiple devices at the same time. However, it can only
display one full screen at a time. When starting up, the projector automatically searches for
the available signals.
Be sure the Quick Auto Search function in the SOURCE menu is On (which is the
default of this projector) if you want the projector to automatically search for the signals.
You can also manually cycle through the
available input signals.
1.
2.
Press SOURCE on the projector or
remote control. A source selection bar
displays.
Press / until your desired signal is
selected and press MODE/ENTER.
Once detected, the selected source information will display on the screen for
seconds. If there is multiple equipment connected to the projector, repeat steps 1-2
to search for another signal.
•
The brightness level of the projected image will change accordingly when you switch
between different input signals. Data (graphic) "PC" presentations using mostly static
images are generally brighter than "Video" using mostly moving images (movies).
•
The input signal type effects the options available for the Picture Mode. See "Selecting a
picture mode" on page 36 for details.
For best display picture results, you should select and use an input signal which outputs at this
resolution. Any other resolutions will be scaled by the projector depending upon the 'aspect
ratio' setting, which may cause some image distortion or loss of picture clarity. See "Selecting
the aspect ratio" on page 34 for details.
Changing Color Space
In the unlikely event that you connect the projector to a DVD player via the projector's
HDMI input and the projected picture displays wrong colors, please change the color space
to YUV.
1.
2.
Press MENU/EXIT and then press
/
until the SOURCE menu is highlighted.
Press
to highlight Color Space Conversion and press
/
to select a
suitable color space.
This function is only available when the HDMI input port is in use.
Operation 33
http://www.pureglare.com.au
Magnifying and searching for details
If you need to find the details on the projected picture, magnify the picture. Use the
direction arrow keys for navigating the picture.
• Using the remote control
1.
Press Digital Zoom +/- to display the Zoom
bar.
2.
Press Digital Zoom + to magnify the center
of the picture. Press the key repeatedly until
the picture size is suitable for your need.
3.
Use the directional arrows ( , ,
,
)
on the projector or remote control to
navigate the picture.
4.
To restore the picture to its original size,
press AUTO. You can also press Digital
Zoom -. When the key is pressed again, the
picture is further reduced until it is restored to the original size.
• Using the OSD menu
1.
Press MENU/EXIT and then press
/ until the DISPLAY menu is highlighted.
2.
Press
to highlight Digital Zoom and press MODE/ENTER. The Zoom bar
displays.
3.
Repeat steps 2-4 in the section of "Using the remote control" above. Or if you are
using the projector control panel, continue to the following steps.
4.
Press
on the projector repeatedly to magnify the picture to a desired size.
5.
To navigate the picture, press MODE/ENTER to switch to the paning mode and
press the directional arrows ( , ,
,
) to navigate the picture.
6.
Use the directional arrows ( , ,
,
) on the projector or remote control to
navigate the picture.
7.
To reduce size of the picture, press MODE/ENTER to switch back to the zoom in/
out functionality, and press AUTO to restore the picture to its original size. You can
also press
repeatedly until it is restored to the original size.
The picture can only be navigated after the picture is magnified. You can further magnify the
picture while searching for details.
Selecting the aspect ratio
The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and
computers are in 4:3 ratio,and digital TV and DVDs are usually in 16:9 or 16:10 ratio.
With the advent of digital signal processing, digital display devices like this projector can
dynamically stretch and scale the image output to a different aspect than that of the image
input signal.
To change the projected image ratio (no matter what aspect the source is):
• Using the remote control
1.
Press ASPECT to show the current setting.
2.
Press ASPECT repeatedly to select an aspect ratio to suit the format of the video
signal and your display requirements.
•
34
Using the OSD menu
Operation
http://www.pureglare.com.au
1.
2.
3.
Press MENU/EXIT and then press
/
until the DISPLAY menu is highlighted.
Press
to highlight Aspect Ratio.
Press / to select an aspect ratio to suit the format of the video signal and your
display requirements.
About the aspect ratio
In the pictures below, the black portions are inactive areas and the white portions are active
areas. OSD menus can be displayed on those unused black areas.
1.
2.
3.
4.
5.
Auto: Scales an image proportionally to fit the projector's native resolution in its
horizontal or vertical width. This is suitable for the incoming image which is neither
in 4:3 nor 16:9 and you want to make most use of the screen without altering the
image's aspect ratio.
Real: The image is projected as its original resolution, and resized to fit within the
display area. For input signals with lower resolutions, the projected image will display
smaller than if resized to full screen. You could adjust the zoom setting or move the
projector towards the screen to increase the image size if necessary. You may also
need to refocus the projector after making these adjustments.
4:3: Scales an image so that it is displayed in the center of the screen with a 4:3
aspect ratio. This is most suitable for 4:3 images like computer monitors, standard
definition TV and 4:3 aspect DVD movies, as it displays them without aspect
alteration.
16:9: Scales an image so that it is displayed in the center of the screen with a 16:9
aspect ratio. This is most suitable for images which are already in a 16:9 aspect, like
high definition TV, as it displays them without aspect alteration.
16:10: Scales an image so that it is displayed in the center of the screen with a 16:10
aspect ratio. This is most suitable for images which are already in a 16:10 aspect, like
high definition TV, as it displays them with out aspect alteration.
Operation 35
http://www.pureglare.com.au
Optimizing the image
Selecting a picture mode
The projector is preset with several predefined
picture modes so that you can choose one to suit
your operating environment and input signal
picture type.
To select an operation mode that suits your need,
you can follow one of the following steps.
•
•
Press MODE/ENTER on the remote control
or projector repeatedly until your desired mode is selected.
Go to the PICTURE > Picture Mode menu and press
/
mode.
to select a desired
The picture modes are listed below.
1.
2.
3.
4.
5.
Dynamic mode: Maximizes the brightness of the projected image. This mode is
suitable for environments where extra-high brightness is required, such as using the
projector in well lit rooms.
Presentation mode (Default): Is designed for presentations. The brightness is
emphasized in this mode.
sRGB mode: Maximizes the purity of RGB colors to provide true-to-life images
regardless of brightness setting. It is most suitable for viewing photos taken with an
sRGB compatible and properly calibrated camera, and for viewing PC graphic and
drawing applications such as AutoCAD.
Cinema mode: Is appropriate for playing colorful movies, video clips from digital
cameras or DVs through the PC input for best viewing in a blackened (little light)
environment.
User 1/User 2 mode: Recalls the settings customized based on the current
available picture modes. See "Setting the User 1/User 2 mode" on page 36 for details.
Setting the User 1/User 2 mode
There are two user-definable modes if the current available picture modes are not suitable
for your need. You can use one of the picture modes (except the User 1/User 2) as a
starting point and customize the settings.
1.
2.
3.
4.
Press MENU/EXIT to open the On-Screen Display (OSD) menu.
Go to the PICTURE > Picture Mode menu.
Press
/
to select User 1 to User 2.
Press
to highlight Reference Mode.
This function is only available when User 1 or User 2 mode is selected up in the Picture Mode
sub-menu item.
5.
6.
7.
8.
36
Press
/
to select a picture mode that is closest to your need.
Press
to select a sub-menu item to be changed and adjust the value with
/
See "Fine-tuning the image quality in user modes" below for details.
When all settings have been done, highlight Save Settings and press MODE/
ENTER to store the settings.
The confirmation message 'Setting Saved' displays.
Operation
http://www.pureglare.com.au
.
Using Wall Color
In the situation where you are projecting onto a colored surface such as a painted wall
which may not be white, the Wall Color feature can help correct the projected picture’s
color to prevent possible color difference between the source and projected pictures.
To use this function, go to the DISPLAY > Wall Color menu and press
/ to select
a color which is the closest to the color of the projection surface. There are several
precalibrated colors to choose from: Light Yellow, Pink, Light Green, Blue, and
Blackboard.
Fine-tuning the image quality in user modes
According to the detected signal type, there are some user-definable functions available
when User 1 or User 2 mode is selected. Based on your needs, you can make
adjustments tothese functions by highlighting them and pressing
/
on the projector
or remote control
Adjusting Brightness
The higher the value, the brighter the image. And the
lower the setting, the darker the image. Adjust this
control so the black areas of the image appear just as
black and that detail in the dark areas is visible.
∫″‰
∫е‰
∫з‰
0
-30
Adjusting Contrast
The higher the value, the greater the contrast. Use this
to set the peak white level after you have previously
adjusted the Brightness setting to suit your selected
input and viewing environment.
+30
Adjusting Color
Lower setting produces less saturated colors. If the setting is too high, colors on the image
will be overpowering, which makes the image unrealistic.
Adjusting Tint
The higher the value, the more reddish the picture becomes. The lower the value, the
more greenish the picture becomes.
Adjusting Sharpness
The higher the value, the sharper the picture becomes. The lower the value, the softer the
picture becomes.
Adjusting Brilliant Color
This feature utilizes a new color-processing algorithm and system level enhancements to
enable higher brightness while providing truer, more vibrant colors in picture. It enables a
greater than 50% brightness increase in mid-tone images, which are common in video and
natural scenes, so the projector reproduces images in realistic and true colors. If you
prefer images with that quality, select On. If you don’t need it, select Off.
On is the default and recommended selection for this projector. When Off is selected, the
Color Temperature function is not available.
Operation 37
http://www.pureglare.com.au
Selecting a Color Temperature
The options available for color temperature* settings vary according to the signal type
selected.
1.
2.
3.
Cool: Makes images appear bluish white.
Normal: Maintains normal colorings for white.
Warm: Makes images appear reddish white.
*About color temperatures:
There are many different shades that are considered to be "white" for various purposes.
One of the common methods of representing white color is known as the “color
temperature”. A white color with a low color temperature appears to be reddish white. A
white color with a high color temperature appears to have more blue in it.
3D Color Management
In most installation situations, color management will not be necessary, such as in
classroom, meeting room, or lounge room situations where lights remain on, or where
building external windows allow daylight into the room.
Only in permanent installations with controlled lighting levels such as boardrooms, lecture
theaters, or home theaters, should color management be considered. Color management
provides fine color control adjustment to allow for more accurate color reproduction,
should you require it.
Proper color management can only be achieved under controlled and reproducible viewing
conditions. You will need to use a colorimeter (color light meter), and provide a set of
suitable source images to measure color reproduction. These tools are not provided with
the projector, however, your projector supplier should be able to provide you with suitable
guidance, or even an experienced professional installer.
The Color Management provides six sets (RGBCMY) of colors to be adjusted. When you
select each color, you can independently adjust its range and saturation according to your
preference.
If you have purchased a test disc which contains various color test patterns and can be
used to test the color presentation on monitors, TVs, projectors, etc. You can project any
image from the disc on the screen and enter the 3D Color Management menu to make
adjustments.
To adjust the settings:
1.
2.
3.
4.
38
Go to the PICTURE menu and highlight 3D Color Management.
Press MODE/ENTER and the 3D Color Management page displays.
Highlight Primary Color and press
/
to select a color from among Red,
Yellow, Green, Cyan, Blue, or Magenta.
Press
to highlight Hue and press
/
to select its range. Increase in the range
will include colors consisted of more proportions of its two adjacent colors.
Operation
http://www.pureglare.com.au
5.
6.
7.
8.
9.
Please refer to the illustration to the right
for how the colors relate to each other.
For example, if you select Red and set its
Yellow
GREEN
RED
range at 0, only pure red in the projected
picture will be selected. Increasing its range
will include red close to yellow and red close
to magenta.
Cyan
Magenta
Press
to highlight Saturation and adjust
its values to your preference by pressing
/
BLUE
. Every adjustment made will reflect to
the image immediately.
For example, if you select Red and set its
value at 0, only the saturation of pure red will be affected.
Saturation is the amount of that color in a video picture. Lower settings produce
less saturated colors; a setting of “0” removes that color from the image entirely. If
the saturation is too high, that color will be overpowering and unrealistic.
Press
to highlight Gain and adjust its values to your preference by pressing
/
. The contrast level of the primary color you select will be affected. Every
adjustment made will reflect to the image immediately.
Repeat steps 3 to 6 for other color adjustments.
Make sure you have made all of the desired adjustments.
Press MENU/EXIT to exit and save the settings.
Creating your own startup screen
In addition to selecting the projector preset startup screen from among BenQ logo, Black
or Blue screen, you can make your own startup screen that is an image projected from
your computer or video source.
1.
Project the image you want to use as your
startup screen from either a computer or
video source.
2.
Press CAPTURE on the remote control or
go to the SYSTEM SETUP: Basic >
MyScreen menu, press MODE/ENTER.
3.
A confirmation message displays. Press
CAPTURE or MODE/ENTER again.
4.
The message 'Screen Capturing...' displays while the projector is processing the
image. Please wait.
5.
If the action is successful, you see the message 'Captured Succeeded' on the
screen. The captured image is saved as MyScreen.
6.
To view the captured image displayed as the startup screen, set MyScreen in the
SYSTEM SETUP: Basic > Splash Screen menu and restart the projector.
In the unlikely event, the capturing action failed. If so, change your target image.
Operation 39
http://www.pureglare.com.au
Setting the presentation timer
The presentation timer can indicate the presentation
time on the screen to help you achieve better time
management when giving presentations. Follow these
steps to utilize this function:
1.
2.
3.
Press Timer Set up on the remote control or
go to the SYSTEM SETUP: Basic >
Presentation Timer menu and press MODE/
ENTER to display the Presentation Timer
page.
Highlight Timer period and decide the timer
period by pressing
/ . The length of time can be set from 1 to 5 minutes in 1minute increments and 5 to 240 minutes in 5-minute increments.
Press
to highlight Timer display and choose if you want the timer to show up
on the screen by pressing
/ .
Selection
Description
Always
Displays the timer on screen throughout the presentation time.
Last 1 min/Last 2
Displays the timer on screen in the last 1/2/3 minute(s).
min/Last 3 min
Never
4.
Press
5.
Top-Left
Bottom-Left
Top-Right
Bottom-Right
Press
to highlight Timer counting direction and select your desired counting
direction by pressing / .
to highlight Timer position and set the timer position by pressing
Selection
Description
Count Up
Increases from 0 to the preset time.
Count Down
Decrease from the preset time to 0.
6.
7.
8.
40
Hides the timer throughout the presentation time.
/
Press
to highlight Sound reminder and decide if you want to activate sound
reminder by pressing
/ . If you select On, a double beep sound will be heard at
the last 30 seconds of counting down/up, and a triple beep sound will be produced
when the timer is up.
To activate the presentation timer, press
and press / to select On and press
MODE/ENTER.
A confirmation message displays. Highlight Yes and press MODE/ENTER to
confirm. You will see the message “Timer is On” displaying on the screen. The
timer starts counting at the time the timer is on.
Operation
http://www.pureglare.com.au
.
To cancel the timer, perform the following steps.
• Using the remote control.
Press Timer On and press
/
to highlight Off and press MODE/ENTER.
• Using the OSD menu.
1.
Go to the SYSTEM SETUP: Basic > Presentation Timer menu and highlight
Off.
Press MODE/ENTER. A confirmation message displays.
2.
Highlight Yes and press MODE/ENTER to confirm. You will see the message
“Timer is Off!” displaying on the screen.
How to use the Timer On key?
Timer On is a multi-functional key.
•
•
If the presentation timer is off, pressing this key
displays a confirmation message. You can decide
whether to activate the timer or not by
following the on-screen instruction.
If the timer is already on, pressing this key
displays a confirmation message. You can decide
whether to restart, continue or turn off the
timer by following the on-screen instruction.
Remote paging operations
Connect the projector to your PC or notebook
with a USB cable prior to using the paging function.
You can operate your display software program (on
a connected PC) which responds to page up/down
commands (like Microsoft PowerPoint) by pressing
Page Up/Down on the remote control.
If remote paging function doesn't work, check if the
USB connection is correctly made and the mouse
driver on your computer is updated to the latest
version.
Operation 41
http://www.pureglare.com.au
Hiding the image
Press the Eco Blank button from projector or remote control to turn off the image for a
period of time with up to 70% lamp power saving. Press any key on the projector or
remote control to restore the image.
The word "Eco Blank" appears at the screen while
the image is hidden. When this function is activated
with an audio input connected,the audio can still be
heard.
The automatic switch to Eco Blank Mode after the
projector is turned on for over three minutes
without a display source, eliminating unnecessary
energy waste and prolonging the life of the projector
lamp
You can set the blank time in the SYSTEM SETUP: Basic > Operation Settings >
Eco Blank Timer menu to let the projector return the image automatically after a
period of time when there is no action taken on the blank screen. The length of time can
be set from 5 to 30 minutes in 5-minute increments.
Do not block the projection lens from projecting as this could cause the blocking object to
become heated.
No matter Eco Blank Timer is activated or not, you can press any key (except the Page
Down key) on the projector or remote control to restore the picture.
Freezing the image
Press
on the remote control to freeze the image.
The word 'FREEZE' will display in the screen. To
release the function, press any key (except the Page
Up/Down key) on the projector or remote control.
Even if an image is frozen on the screen, the pictures
are running on the video or other device. If the
connected devices have active audio output, you will
still hear the audio even though the image is frozen
on screen.
42
Operation
http://www.pureglare.com.au
Up/
Operating in a high altitude environment
We recommend you use the High Altitude Mode when your environment is between
1500 m –3000 m above sea level, and ambient temperature is between 0°C–35°C.
Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and ambient
temperature is between 0°C and 35°C. The projector will be over cooled, if you turn the mode
on under such a condition.
To activate the High Altitude Mode:
1.
Press MENU/EXIT and then press
/
until the SYSTEM SETUP:
Advanced menu is highlighted.
2.
Press
to highlight High Altitude Mode and press
/
to select On. A
confirmation message displays.
3.
Highlight Yes and press MODE/ENTER.
Operation under "High Altitude Mode" may cause a higher decibel operating noise level
because of increased fan speed necessary to improve overall system cooling and
performance.
If you use this projector under other extreme conditions excluding the above, it may
display auto shut-down symptoms, which is designed to protect your projector from overheating. In cases like this, you should switch to High Altitude mode to solve these
symptoms. However, this is not to state that this projector can operate under any and all
harsh or extreme conditions.
Adjusting the sound
The sound adjustments made as below will have an effect on the projector speaker(s). Be
sure you have made a correct connection to the projector audio input. See "Connection"
on page 19 for how the audio input is connected.
Muting the sound
To temporarily turn off the sound:
1.
2.
3.
Press MENU/EXIT and then press
/
until the SYSTEM SETUP:
Advanced menu is highlighted.
Press
to highlight Audio Settings and press MODE/ENTER. The Audio
Settings page displays.
Highlight Mute and press
/
to select On.
Adjusting the sound level
To adjust the sound level, press Volume +/- on the
remote control, or:
1.
2.
Repeat steps 1-2 above.
Press
to highlight Volume and press
to select a desired sound level.
/
Operation 43
http://www.pureglare.com.au
Use Teaching Template
Making writing on the board easier for teachers, you can use build-in template by OSD or
remote control.
Open the OSD menu and go to the DISPLAY > Teaching Template . Choice
Blackboard/ Whiteboard. > Off/ Letter Formation/ Musical Staff/ Worksheet/
Coordinate Chart. The Teaching Template displays.
Teaching
Template
Whiteboard
Letter
Formation
Musical Staff
Worksheet
Coordinate
Chart
44
Operation
http://www.pureglare.com.au
Blackboard
Personalizing the projector menu display
The On-Screen Display (OSD) menus can be set according to your preferences. The
following settings do not affect the projection settings, operation, or performance.
•
•
•
•
•
Menu display time in the SYSTEM SETUP: Advanced > Menu Settings menu
sets the length of time the OSD will remain active after your last key press. The time
length ranges from 5 to 30 seconds in 5-second increments. Use
/
to select a
suitable time frame.
Menu position in the SYSTEM SETUP: Advanced > Menu Settings menu sets
the OSD position in five locations. Use
/
to select a preferred position.
Language in the SYSTEM SETUP: Basic menu sets your familiar language for the
OSD menus. Use
/
to select your language.
Reminder Message in the SYSTEM SETUP: Advanced > Menu Settings menu
sets whether to display reminder messages on screen. Use
/
to select your
desired setting.
Splash Screen in the SYSTEM SETUP: Basic menu sets a preferred logo screen
to be displayed during projector start-up. Use
/
to select a screen.
Select the lamp saver mode
• Using the remote control.
Press Smart Eco and Highlight Lamp mode and press
Economic/Smart Eco.
/
to select Normal/
• Using the OSD menu.
1.
Press Menu/Exit and then press
/
until the SYSTEM SETUP: Advanced
menu is highlighted.
2.
Press
to highlight Lamp mode and press
Mode/Enter. The Lamp Settings page
displays.
3.
Highlight Lamp mode and press
/
to select Normal/Economic/Smart
Eco. The lamp brightness vary from the different lamp mode,see the description list
in table below.
Lamp mode
Description
Normal
100% lamp brightness.
Economic
80% lamp power consumption.
Smart Eco
This is default setting. Lamp power consumption will save from 30% to
100% dynamically by detecting the content brightness level.
If the Economic mode is selected, the light output will be reduced and result in darker projected
pictures.
Operation 45
http://www.pureglare.com.au
Shutting down the projector
1.
Press II POWER and a confirmation
message displays prompting you.
If you don't respond in a few seconds, the
message will disappear.
2.
Press II POWER a second time. The
POWER indicator light flashes orange, the
projection lamp shuts down, and the fans will
continue to run for approximately 90 seconds
to cool down the projector.
•
To protect the lamp, the projector will not respond
to any commands during the cooling process.
•
To shorten the cooling time, you can also activate
the Quick Cooling function. See "Quick Cooling"
on page 55 for details.
3.
4.
5.
46
Once the cooling process finishes, the POWER indicator light is a steady orange
and fans stop.
Disconnect the power cord from the power putlet if the projector will not be used
in an extended period of time.
When Instant Restart is On, users can restart projector immediately within 90
secs after turning off projector. (Projector will maintain 30% of power during the 90
secs)
When Instant Restart is Off, users need to wait lamp to cool down to restart the
projector. When instant restart is on, quick cooling item will be grey out
•
If the projector is not properly shut down, to protect the lamp, when you attempt to re-start
the projector, the fans will run for a few minutes to cool down. Press Power again to start
the projector after the fans stop and the POWER indicator light turns orange.
•
Actual lamp life may vary due to different environmental conditions and usage.
Operation
http://www.pureglare.com.au
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type
selected.
Main menu
Sub-menu
Options
Wall Color
Off/Light Yellow/Pink/Light
Green/Blue/Blackboard
Aspect Ratio
Auto/Real/4:3/16:9/16:10
Keystone
Position
Phase
1.
DISPLAY
H. Size
Digital Zoom
3D Sync
Off/Top-Bottom/Frame sequential
3D Sync Invert
On/Off
Blackboard
Off/Letter Formation/Musical
Staff/Worksheet/Coordinate
Chart
Whiteboard
Off/Letter Formation/Musical
Staff/Worksheet/Coordinate
Chart
Teaching
Template
Picture Mode
Dynamic/Presentation/sRGB/Cinema/User 1/User
2
Reference Mode Dynamic/Presentation/sRGB/Cinema
Brightness
Contrast
Color
Tint
2.
PICTURE
Sharpness
Brilliant Color
On/Off
Color
Temperature
Cool/Normal/Warm
Primary Color
3D Color
Management
R/G/B/C/M/Y
Hue
Saturation
Gain
Save Settings
3. SOURCE
Quick Auto Search
On/Off
Color Space Conversion
Auto/RGB/YUV
Operation 47
http://www.pureglare.com.au
Presentation
Timer
Timer period
1~240 minutes
Timer display
Always/Last 1 min/Last 2 min/
Last 3 min/Never
Timer position
Top-Left/Bottom-Left/TopRight/Bottom-Right
Timer counting
direction
Count Down/Count Up
Sound reminder
On/Off
On/Off
Yes/No
Language
4.
SYSTEM
SETUP:
Basic
Projector Position
Menu Settings
Operation
Settings
Menu display time
5 sec/10 sec/15 sec/20 sec/25
sec/30 sec
Menu position
Center/Top-left/Top-right/
Bottom-right/Bottom-left
Reminder message
On/Off
Direct power on
On/Off
Auto Power Off
Disable/5 min/10 min/15 min/
20 min/25 min/30 min
Eco Blank Timer
Disable/5 min/10 min/15 min/
20 min/25 min/30 min
Sleep Timer
Disable/30 min/1 hr/2 hr/3 hr/4
hr/8 hr/12 hr
Quick Cooling
On/Off
Instant Restart
On/Off
Panel Key Lock On/Off
Yes/No
Background
Color
BenQ/Black/Blue/Purple
Splash Screen
MyScreen
48
Front Table/Rear Table/Rear
Ceiling/Front Ceiling
BenQ/Black/Blue/MyScreen
Capture
Operation
http://www.pureglare.com.au
Yes/No
High Altitude
Mode
Audio Settings
Lamp Settings
Off/On
Yes/No
Mute
Off/On
Volume
Power on/off Ring
Tone
Off/On
Lamp mode
Normal/Economic/Smart Eco
Reset lamp timer
Reset/Cancel
Equivalent lamp hour
5.
SYSTEM Security
Settings
SETUP:
Advanced
Change password
Change Security
Settings
Power on lock
Splash Screen Lock
Baud Rate
2400/4800/9600/14400/19200/
38400/57600/115200
Test Pattern
On/Off
Closed Caption
Closed Caption Enable
Caption Version
Standby
Settings
Monitor Out
Off/On
CC1/CC2/CC3/CC4
On/Off
Reset All
Settings
6.
INFORMAT Current System Status
ION
•
•
•
•
•
•
Source
Picture Mode
Resolution
Color System
Equivalent Lamp Hour
Firmware Version
Note that the menu items are available when the projector detects at least one valid signal.
If there is no equipment connected to the projector or no signal detected, limited menu
items are accessible.
Operation 49
http://www.pureglare.com.au
Description of each menu
•
The default values listed in this manual, especially on pages 50-58, are for reference only.
They may vary between the projectors due to the continuous improvement to the
products.
FUNCTION
DESCRIPTION
Wall Color
Corrects the projected picture’s color when the projection surface is
not white. See "Using Wall Color" on page 37 for details.
There are four options to set the image's aspect ratio depending on
your input signal source. See "Selecting the aspect ratio" on page 34
for details.
Corrects any keystoning of the image. See "Correcting keystone" on
page 28 for details.
Displays the position adjustment page. To move the projected image,
use the directional arrow keys. The values shown on the lower
position of the page change with every key press you made until they
reach their maximum or minimum.
Aspect Ratio
Keystone
1. DISPLAY menu
Position
This function is only available when a PC signal (analog RGB) is
selected.
Adjusts the clock phase to reduce image
distortion.
Phase
H. Size
This function is only available when a
PC signal (analog RGB) is selected.
Adjusts the horizontal width of the image.
This function is only available when a PC signal (analog RGB) is
selected.
or reduces the projected image. See "Magnifying and
Digital Zoom Magnifies
searching for details" on page 34 for details.
50
Operation
http://www.pureglare.com.au
FUNCTION
DESCRIPTION
This projector features a 3D function which enables you to enjoy the
3D movies, videos, and sporting events in a more realistic way by
presenting the depth of the images. You need to wear a pair of 3D
glasses to view the 3D images.
• For a PC type signal:
When the vertical frequency is 120Hz, and the content being
projected is made with 3D technology, selecting On will present the
3D images.
1. DISPLAY menu
3D Sync
When the input signal is [email protected], 3D sync will be enabled
automatically.
• For a video type signal:
When the content being projected is made with 3D technology,
selecting On will present the 3D images.
When 3D Sync function is enabled, the projector will enter a special
picture mode and the current picture mode adjustment will be
disabled.
3D Sync
Invert
Teaching
Template
This function is only enabled when the input signal is
[email protected], [email protected] and S-video.
When you discover the inversion of the image depth, enable this
function to correct the problem.
This function is only enabled when the input signal is
[email protected], Video and S-video.
Provides some templates as teaching aids. Teachers can use them for
teaching. See "Use Teaching Template" on page 44 for details.
Operation 51
http://www.pureglare.com.au
FUNCTION
DESCRIPTION
Pre-defined picture modes are provided so you can optimize your
Picture Mode projector image set-up to suit your program type. See "Selecting a
Reference
Mode
Brightness
picture mode" on page 36 for details.
Selects a picture mode that best suits your need for the image quality
and further fine-tune the image based on the selections listed on the
same page below. See "Setting the User 1/User 2 mode" on page 36
for details.
This function is only available when User 1/2 is
selected.
Adjusts the brightness of the image. See "Adjusting Brightness" on
page 37 for details.
This function is only available when User 1/2 is selected.
2. PICTURE menu
Contrast
Adjusts the degree of difference between dark and light in the image.
See"Adjusting Contrast" on page 37 for details.
This function is only available when User 1/2 is selected.
Color
Adjusts the color saturation level -- the amount of each color in a
video image. See "Adjusting Color" on page 37 for details.
This function is only available when User 1/2 is selected.
This function is only available when a Video or S-Video signal
is selected and the system format is NTSC or PAL.
Adjusts the red and green color tones of the image. See "Adjusting
Tint" on page 37 for details.
Tint
Sharpness
This function is only available when User 1/2 is selected.
This function is only available when a Video or SVideo signal is selected and the system format is
NTSC or PAL..
Adjusts the image to make it look sharper or softer. See "Adjusting
Sharpness" on page 37 for details.
This function is only available when User 1/2 is selected.
This function is only available when a Video or S-Video signal
is selected and the system format is NTSC or PAL.
52
Operation
http://www.pureglare.com.au
FUNCTION
2. PICTURE menu
Brilliant
Color
DESCRIPTION
Adjusts white peaking while maintaining correct color presentation.
See "Adjusting Brilliant Color" on page 37 for details.
This function is only available when User 1/2 is selected.
See "Selecting a Color Temperature" on page 38 for details.
Color
This function is only available when User 1/2 is selected.
Temperature
3D Color
Management
Save Settings
See "3D Color Management" on page 38 for details.
This function is only available when User 1/2 is
selected.
Saves the settings made for User 1 or User 2 mode.
This function is only available when User 1/2 is selected.
3. SOURCE
menu
Quick Auto
Search
See "Switching input signal" on page 33 for details.
Color Space
Conversion
See "Changing Color Space" on page 33 for details.
Operation 53
http://www.pureglare.com.au
4. SYSTEM SETUP:
Basic menu
FUNCTION
DESCRIPTION
Presentation
Timer
Reminds the presenter to finish the presentation within a certain
time frame. See "Setting the presentation timer" on page 40 for
details.
Sets the language for the On-Screen Display (OSD) menus. See
"Using the menus" on page 29 for details.
The projector can be installed on a ceiling or behind a screen, or with
one or more mirrors. See "Choosing a location" on page 15 for
details.
Menu display time
Sets the length of time the OSD will remain active after your last key
press. The range is from 5 to 30 seconds in 5-second increments.
Language
Projector
Position
Menu
Settings
Menu position
Sets the On-Screen Display (OSD) menu position.
Reminder message
Sets whether to display the reminder message.
54
Operation
http://www.pureglare.com.au
FUNCTION
DESCRIPTION
Direct Power On
Selecting On enables the function. See "Starting up the projector" on
page 25 for details.
Auto Power Off
Allows the projector to turn off automatically if no input signal is
detected after a set period of time. See "Setting Auto Power Off" on
page 60 for details.
Eco Blank Timer
Sets the image blank time when the Blank feature is activated, once
elapsed the image will return to the screen. See "Hiding the image"
on page 42 for details.
4. SYSTEM SETUP:
Basic menu
Operation
Settings
Sleep Timer
Sets the auto-shutdown timer. The timer can be set to a value
between 30 minutes and 12 hours.
Quick Cooling
Selecting On enables the function and the projector cooling time will
be shortened to a few seconds.
If you attempt to restart the projector right after the
quick cooling process, it may not be turned on
successfully and will rerun its cooling fans.
Panel Key
Lock
Instant Restart
When instant restart is on, users can restart projector immediately
within 90 secs after turning off projector.
Disables or enables all panel key functions except Power on the
projector and keys on the remote control.
Allows you to select which background color will display when no
signal is input into the projector. Four options are available: BenQ
logo, Black, Blue, or Purple.
Allows you to select which logo screen will display during projector
Splash Screen start-up. Three options are available: BenQ logo, Black screen, or
Blue screen.
Captures and stores the projected picture as My Screen. See
"Creating your own startup screen" on page 39 for details.
Background
Color
MyScreen
In the unlikely event that the capturing action fails,
change your target picture.
Operation 55
http://www.pureglare.com.au
FUNCTION
DESCRIPTION
High Altitude A mode for operation in high altitude areas. See "Operating in a high
altitude environment" on page 43 for details.
Mode
Allows you to enter the audio setting menu.
Audio
Settings
Mute
Sets the mute function.
Volume
Adjusts the audio volume level.
5. SYSTEM SETUP: Advanced menu
power on/off ring tone
Lamp mode
See "Setting Lamp mode eco function as Economic or Smart Eco
mode" on page 60 for details.
Lamp
Settings
Equivalent lamp hour
See "Getting to know the lamp hour" on page 60 for details on how
the total lamp hour is calculated.
Change password
You will be asked to enter the current password before changing to a
new one.
Security
Settings
Change Security Settings
Power on lock
See "Securing the projector" on page 30 for details.
Baud Rate
Splash Sscreen On Lock
When Splash screen lock is activated, My Screen cannot be used
unless the correct password is entered every time when you attempt
to capture screen.
Selects a baud rate that is identical with your computer’s so that you
can connect the projector using a suitable RS-232 cable and update
or download the projector’s firmware. This function is intended for
qualified service personnel.
Selecting On enables the function and the projector displays the grid
test pattern. It helps you adjust the image size and focus and check
that the projected image is free from distortion. See "Use build-in
test pattern" on page 27 for details.
Test Pattern
56
Reset lamp timer
See "Resetting the lamp timer" on page 64 for details.
Operation
http://www.pureglare.com.au
FUNCTION
DESCRIPTION
Closed Caption Enable
Activates the function by selecting On when the selected input signal
carries closed captions.
5. SYSTEM SETUP: Advanced menu
Closed
Caption
Standby
Settings
•
Captions: An on-screen display of the dialogue, narration, and
sound effects of TV programs and videos that are closed
captioned (usually marked as "CC" in TV listings).
Caption Version
Selects a preferred closed captioning mode. To view captions, select
CC1, CC2, CC3, or CC4 (CC1 displays captions in the primary
language in your area).
Monitor Out
Selecting On enables the function. The projector can output a VGA
signal when it is in standby mode and the COMPUTER 1 and
MONITOR-OUT jacks are correctly connected to devices. See
"Connecting a monitor" on page 20 for how to make the connection.
Enabling this function slightly increases the standby power
consumption.
The Standby Monitor Out only works when an appropriate D-Sub
input is made to the COMPUTER 1 jack.
Reset All
Settings
Returns all settings to the factory preset values.
The following settings will still remain: Position, Phase, H. Size,
User 1, User 2, Language, Projector Position, High Altitude
Mode, Security Settings, Baud Rate.
Operation 57
http://www.pureglare.com.au
FUNCTION
DESCRIPTION
Source
Shows the current signal source.
6. INFORMATION menu
Picture Mode
Shows the selected mode in the PICTURE menu.
Current
System
Status
Resolution
Shows the native resolution of the input signal.
Color System
Shows input system format, NTSC, PAL, SECAM, or RGB.
Equivalent Lamp Hour
Displays the number of hours the lamp has been used.
Firmware Version
Shows firmware version.
58
Operation
http://www.pureglare.com.au
Maintenance
Care of the projector
Your projector needs little maintenance. The only thing you need to do on a regular basis
is to keep the lens and case clean.
Never remove any parts of the projector except the lamp. Contact your dealer if other
parts need replacing.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface.
•
•
•
Use a canister of compressed air to remove dust.
If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens
cleaner and gently wipe the lens surface.
Never use any type of abrasive pad, alkaline/acid cleaner, scouring powder, or volatile
solvent, such as alcohol, benzene, thinner or insecticide. Using such materials or
maintaining prolonged contact with rubber or vinyl materials may result in damage to
the projector surface and cabinet material.
Never rub the lens with abrasive materials.
Cleaning the projector case
Before you clean the case, turn the projector off using the proper shutdown procedure as
described in "Shutting down the projector" on page 46 and unplug the power cord.
•
•
To remove dirt or dust, wipe the case with a soft, lint-free cloth.
To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH
detergent. Then wipe the case.
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the
case.
Storing the projector
If you need to store the projector for an extended time, please follow the instructions
below:
•
•
•
•
Make sure the temperature and humidity of the storage area are within the
recommended range for the projector. Please refer to "Specifications" on page 67 or
consult your dealer about the range.
Retract the adjuster feet.
Remove the battery from the remote control.
Pack the projector in its original packing or equivalent.
Transporting the projector
It is recommended that you ship the projector with its original packing or equivalent.
Maintenance 59
http://www.pureglare.com.au
Lamp information
Getting to know the lamp hour
When the projector is in operation, the duration (in hours) of lamp usage is automatically
calculated by the built-in timer. The method of calculating the equivalent lamp hour is as
follows:
Total (equivalent) lamp hour
= 1 (hours used in Economic mode) + 4/3 (hours used in normal mode)
See "Setting Lamp mode eco function as Economic or Smart Eco mode" below for more
information on Economic mode.
The lamp hour in Economic mode is calculated as 3/4 of that in Normal mode. That is,
using the projector in Economic mode helps to extend the lamp hour by 1/3.
To obtain the lamp hour information:
1.
Press Menu/Exit and then press / until the SYSTEM SETUP: Advanced
menu is highlighted.
2.
Press to highlight Lamp Settings and press Mode/Enter. The Lamp Settings
page displays.
3.
You will see the Equivalent lamp hour information displaying on the menu.
4.
To leave the menu, press Menu/Exit.
You can also get the lamp hour information on the INFORMATION menu.
Extending lamp life
The projection lamp is a consumable item. To keep the lamp life as long as possible, you
can do the following settings via the OSD menu or remote control.
Setting Lamp mode eco function as Economic or Smart Eco mode
Using Economic /Smart Eco mode will reduces system noise and power consumption.
If the Economic/Smart Eco mode is selected, the light output will be reduced and result in
darker projected pictures, the projector protected for longer working life.
Setting the projector in Economic/Smart Eco mode also extends the lamp operation
life. To set Economic/Smart Eco mode, go into the SYSTEM SETUP: Advanced >
Lamp Settings > Lamp mode menu and press / . .
The lamp modes are defined as the chart below.
Lamp mode
Normal
Economic
Smart Eco
Description
100% lamp brightness.
80% lamp power consumption.
This is default setting. Lamp power consumption will save from 30% to
100% dynamically by detecting the content brightness level.
Setting Auto Power Off
This function allows the projector to turn off automatically if no input source is detected
after a set period of time to prevent unnecessary waste of lamp life.
To set Auto Power Off, go into the SYSTEM SETUP: Basic > Auto Power Off
menu and press / . The time period can be set from 5 to 30 minutes in 5-minute
increments. If the preset time lengths are not suitable for your presentation, select
Disable. The projector will not automatically shut down in a certain time period.
60
Maintenance
http://www.pureglare.com.au
Timing of replacing the lamp
When the Lamp indicator lights up red or a message appears suggesting it is time to
replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a
malfunction in the projector and in some instances the lamp may explode.
Do not attempt to replace the lamp yourself. Contact the qualified service personnel for
replacement.
The Lamp indicator light and Temperature warning light will light up if the lamp becomes too
hot. See "Indicators" on page 65 for details.
The following lamp warning displays will remind you to change the lamp.
The warning messages below are for reference only. Please follow the actual on-screen
instructions to prepare and replace the lamp.
Status
Message
Install a new lamp for optimal performance. If the
projector is normally run with Economic
selected ("Setting Lamp mode eco function as
Economic or Smart Eco mode" on page 60), you
may continue to operate the projector until the
next lamp warning appears.
A new lamp should be fitted to avoid the
inconvenience when the projector runs out of
lamp time.
It is strongly recommended that you replace the
lamp at this stage. The lamp is a consumable item.
The lamp brightness diminishes with use. This is
normal lamp behavior. You can replace the lamp
whenever you notice that the brightness level has
significantly diminished.
The lamp MUST be replaced before the projector
will operate normally.
"XXXX" shown in the above messages are numbers that vary depending on different models.
Maintenance 61
http://www.pureglare.com.au
Replacing the lamp
•
Hg - Lamp contains mercury. Manage in accordance with local disposal laws. See
www.lamprecycle.org.
•
If lamp replacement is performed while the projector is suspended upside-down from the
ceiling, make sure that no one is underneath the lamp socket to avoid any possible injury or
damage to the human eyes caused by fractured lamp.
•
To reduce the risk of electrical shock, always turn the projector off and disconnect the power
cord before changing the lamp.
•
To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before
replacing the lamp.
•
To reduce the risk of injuries to fingers and damage to internal components, use caution
when removing lamp glass that has shattered into sharp pieces.
•
To reduce the risk of injuries to fingers and/or compromising image quality by touching the
lens, do not touch the empty lamp compartment when the lamp is removed.
•
This lamp contains mercury. Consult your local hazardous waste regulations to dispose of
this lamp in a proper manner.
•
To assure optimal performance from the projector, it is recommended that you purchase a
BenQ projector lamp for lamp replacement.
1.
2.
62
Turn the power off and disconnect the projector from the power outlet. If the lamp
is hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled.
Loosen the screw on the lamp cover.
Maintenance
http://www.pureglare.com.au
3.
•
Remove the lamp cover by (a) sliding
the cover toward the side of the
projector and (b) lifting it off.
Do not turn the power on with the lamp
cover removed.
•
Do not insert your fingers between the
lamp and the projector. The sharp edges
inside the projector may cause injuries.
4.
Loosen the screws that secure the
lamp.
5.
Lift the handle so that it stands up. Use
the handle to slowly pull the lamp out
of the projector.
•
Pulling it too quickly may cause the lamp to
break and scatter broken glass in the
projector.
•
Do not place the lamp in locations where
water might splash on it, children can reach
it, or near flammable materials.
•
Do not insert your hands into the projector
after the lamp is removed. If you touch the
optical components inside, it could cause
color unevenness and distortion of the
projected images.
6.
Insert the new lamp into the lamp
compartment and make sure it fits in
the projector.
(b)
(a)
Maintenance 63
http://www.pureglare.com.au
7.
Tighten the screws that secure the
lamp.
•
Loose screw may cause a bad connection,
which could result in malfunction.
•
Do not over tighten the screws.
8.
Ensure the handle is fully laid flat and
locked in place.
9.
Replace the lamp cover by sliding it
into place.
(a)
(b)
10.
Tighten the screw that secures the
lamp cover.
•
Loose screw may cause a bad connection,
which could result in malfunction.
•
Do not over tighten the screw.
11.
Restart the projector.
Do not turn the power on with the lamp cover removed.
Resetting the lamp timer
12.
After the startup logo, open the On-Screen
Display (OSD) menu. Go to the SYSTEM
SETUP: Advanced > Lamp Settings
menu. Press Mode/Enter. The Lamp
Settings page displays. Press to highlight
Reset lamp timer and press Mode/Enter.
A warning message displays asking if you want to reset the lamp timer. Highlight
Reset and press Mode/Enter. The lamp time will be reset to '0'.
Do not reset if the lamp is not new or replaced as this could cause damage.
64
Maintenance
http://www.pureglare.com.au
Indicators
Light
Status & Description
POWER TEMP
LAMP
Power events
Orange
Off
Off
Stand-by mode
Green
Flashing
Off
Off
Powering up
Green
Off
Off
Orange
Flashing
Off
Off
Normal operation
1.
The projector needs 90 seconds to cool down as it
was abnormally shut down without the normal cooling
down process. Or
2.
The projector needs to cool for 90 seconds after the
power is turned off. Or
3.
The projector has shutdown automatically. If you try
to re-start the projector, it will shutdown again. Please
contact your dealer for assistance.
Lamp events
Off
Off
Off
Off
The projector has shutdown automatically. If you try to restart the projector, it will shutdown again. Please contact
your dealer for assistance.
1.
The projector needs 90 seconds to cool down. Or
Red
Flashing 2.
Please contact your dealer for assistance.
Red
Thermal events
Off
Red
Flashing
Off
Off
Red
Off
Orange
Flashing
Off
Off
The projector has shutdown automatically. If you try to restart the projector, it will shutdown again. Please contact
your dealer for assistance.
Maintenance 65
http://www.pureglare.com.au
Troubleshooting
The projector does not turn on.
Cause
Remedy
Plug the power cord into the AC inlet on the
projector, and plug the power cord into the
There is no power from the power cable.
power outlet. If the power outlet has a switch,
make sure that it is switched on.
Attempting to turn the projector on again Wait until the cooling down process has
during the cooling process.
completed.
No picture
Cause
Remedy
The video source is not turned on or
connected correctly.
Turn the video source on and check that the signal
cable is connected correctly.
The projector is not correctly connected
to the input signal device.
Check the connection.
The input signal has not been correctly
selected.
Select the correct input signal with the SOURCE
key on the projector or remote control.
The lens cover is still closed.
Open the lens cover.
Blurred image
Cause
Remedy
The projection lens is not correctly
focused.
Adjust the focus of the lens using the focus ring.
The projector and the screen are not
aligned properly.
Adjust the projection angle and direction as well
as the height of the unit if necessary.
The lens cover is still closed.
Open the lens cover.
Remote control does not work
Cause
Remedy
The battery is out of power.
Replace the battery with new one.
There is an obstacle between the remote
control and the projector.
Remove the obstacle.
You are too far away from the projector.
Stand within 8 meters (26 feet) of the projector.
The password is incorrect
66
Cause
Remedy
You do not remember the password.
Please see "Entering the password recall
procedure" on page 31 for details.
Troubleshooting
http://www.pureglare.com.au
Specifications
All specifications are subject to change without notice.
Optical
Output terminals
Resolution
(MX514)
1024 x 768 XGA
(MS513)
800 x 600 SVGA
(MW516)
1280 x 800 WXGA
Display system
1-CHIP DMD
Lens F/Number
(MX514/MS513)
F = 2.51 to 2.69,
f = 21.95 to 24.18 mm
(MW516)
F = 2.55
f = 2.55 to 3.06 mm
Offset: 130+-5%
Zoom ratio:manual zoom,
1.1X(MX514/MS513)1.2X(MW516)
Throw ratio:
1.97-2.17(60"@2.4m)(MX514/MS513)
1.2-1.5(38.7"@1m)(MW516)
Lamp
190 W lamp
Lamp life
(normal/economic mode/smart eco
mode)* 4500/6000/6500
RGB output
D-Sub 15-pin (female) x 1
Speaker
(Stereo) 2 watt x 1
Electrical
Environmental Requirements
Power supply
AC100–240V, 2.9 A,
50-60 Hz (Automatic)
Power consumption
265 W (Max); < 1 W (Standby)
Mechanical
Weight
2.45 Kg (5.4 lbs)
Control
RS-232 serial control
9 pin x 1
IR receiver x 1
USB Type B x 1
Input terminals
Computer input
RGB input
D-Sub 15-pin (female) x 2
Video signal input
S-VIDEO
Mini DIN 4-pin port x 1
VIDEO
RCA jack x 1
SD/HDTV signal input
Analog - Component RCA jack x 3
(through RGB input)
Digital-HDMI x 1
Audio signal input
Audio in
PC audio jack x 1
Audio out
PC audio jack x 1
Operating temperature
0°C-40°C at sea level
Operating relative humidity
10%-90% (without condensation)
Operating altitude
0-1499 m at 0°C-35°C
1500-3000 m at 0°C-30°C (with High
Altitude Mode on)
Lamp life results will vary depending on environmental conditions and usage
Specifications 67
http://www.pureglare.com.au
Dimensions
301.7 mm (W) x 123.4 mm (H) x 232.5 mm (D)
301.7
232.5
123.4
68.3
71.2
Ceiling mount installation
Ceiling mount screws:
M4 x 8 (Max. L = 8 mm)
65.4
149.5
228.0
Unit: mm
71.2
20.0
242.1
82.4
301.7
68
Specifications
http://www.pureglare.com.au
115.8
117.0
Timing chart
Supported timing for PC input
Resolution
720 x 400
640 x 480
800 x 600
1024 x 768
1024 x 576
1024 x 600
1024 x 600
1280 x 800
1280 x 1024
1280 x 960
1440 x 900
1400 x 1050
1600 x 1200
640 x [email protected]
832 x [email protected]
1024 x
[email protected]
1152 x
[email protected]
640 x 480
800 x 600
1024 x 768
Horizontal
Frequency
(kHz)
31.469
31.469
37.861
37.500
43.269
37.879
48.077
46.875
53.674
48.363
56.476
60.023
68.677
35.820
37.5
41.467
49.702
62.795
71.554
63.981
79.976
91.146
60.000
85.938
55.935
65.317
75.000
35.000
49.722
60.241
Vertical
Frequency
(Hz)
70.087
59.940
72.809
75.000
85.008
60.317
72.188
75.000
85.061
60.004
70.069
75.029
84.997
60.0
60.0
64.995
59.810
74.934
84.880
60.020
75.025
85.024
60.000
85.002
59.887
59.978
60.000
66.667
74.546
75.020
Pixel
Frequency
(MHz)
28.322
25.175
31.500
31.500
36.000
40.000
50.000
49.500
56.250
65.000
75.000
78.750
94.500
46.996
45.000
51.419
83.500
106.500
122.500
108.000
135.000
157.500
108
148.500
106.500
121.750
162.000
30.240
57.280
80.000
Mode
720 x 400_70
VGA_60
VGA_72
VGA_75
VGA_85
SVGA_60
SVGA_72
SVGA_75
SVGA_85
XGA_60
XGA_70
XGA_75
XGA_85
Netbook_1
Netbook_2
Netbook_3
WXGA_60
WXGA_75
WXGA_85
SXGA_60
SXGA_75
SXGA_85
1280 x 960_60
1280 x 960_85
WXGA+_60
SXGA+_60
UXGA
MAC13
MAC16
MAC19
68.680
75.060
100.000
MAC21
61.910
77.425
97.551
119.518
119.854
119.989
52.500
83.000
115.5
VGA_120*
SVGA_120*
XGA_120*
*Supported timing for 3D function.
Specifications 69
http://www.pureglare.com.au
Supported timing for HDMI input
Resolution
720 x 400
640 x 480
800 x 600
1024 x 768
1280 x 800
1280 x 1024
1280 x 960
1440 x 900
1400 x 1050
1600 x 1200
640 x [email protected]
832 x [email protected]
1024 x [email protected]
1152 x [email protected]
VIDEO
(HDCP)
Horizontal
Frequency
(kHz)
31.469
31.469
37.861
37.500
43.269
37.879
48.077
46.875
53.674
48.363
56.476
60.023
68.677
49.702
62.795
71.554
63.981
79.976
91.146
60.000
85.938
55.935
65.317
75.000
35.000
49.722
60.241
68.680
31.47
31.25
45.00
37.50
33.75
28.13
67.5
56.25
Vertical
Frequency
(Hz)
70.087
59.940
72.809
75.000
85.008
60.317
72.188
75.000
85.061
60.004
70.069
75.029
84.997
59.810
74.934
84.880
60.020
75.025
85.024
60.000
85.002
59.887
59.978
60.000
66.667
74.546
75.020
75.060
60
50
60
50
60
50
60
50
Pixel
Frequency
(MHz)
28.322
25.175
31.500
31.500
36.000
40.000
50.000
49.500
56.250
65.000
75.000
78.750
94.500
83.500
106.500
122.500
108.000
135.000
157.500
108
148.500
106.500
121.750
162.000
30.240
57.280
80.000
100.000
27
27
74.25
74.25
74.25
74.25
148.5
148.5
Mode
720 x 400_70
VGA_60
VGA_72
VGA_75
VGA_85
SVGA_60
SVGA_72
SVGA_75
SVGA_85
XGA_60
XGA_70
XGA_75
XGA_85
WXGA_60
WXGA_75
WXGA_85
SXGA_60
SXGA_75
SXGA_85
1280 x 960_60
1280 x 960_85
WXGA+_60
SXGA+_60
UXGA
MAC13
MAC16
MAC19
MAC21
480p
576p
720p_60
720_50
1080i_60
1080i_50
1080p
1080p
Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image
vibration.
70
Specifications
http://www.pureglare.com.au
Supported timing for Component-YPbPr input
Signal Format
480i(525i)@60Hz
480p(525p)@60Hz
576i(625i)@50Hz
576p(625p)@50Hz
720p(750p)@60Hz
720p(750p)@50Hz
1080i(1125i)@60Hz
1080i(1125i)@50Hz
[email protected]
[email protected]
Horizontal Frequency
(kHz)
15.73
31.47
15.63
31.25
45.00
37.50
33.75
28.13
67.5
56.25
Vertical Frequency (Hz)
59.94
59.94
50.00
50.00
60.00
50.00
60.00
50.00
60.00
50.00
Displaying a [email protected] or [email protected] signal may result in slight image vibration.
Supported timing for Video and S-Video inputs
Video mode
NTSC*
PAL
SECAM
PAL-M
PAL-N
PAL-60
NTSC4.43
Horizontal
Frequency (kHz)
15.73
15.63
15.63
15.73
15.63
15.73
15.73
Vertical
Frequency (Hz)
60
50
50
60
50
60
60
Color sub-carrier
Frequency (MHz)
3.58
4.43
4.25 or 4.41
3.58
3.58
4.43
4.43
*Supported timing for 3D function.
Specifications 71
http://www.pureglare.com.au
Warranty and Copyright information
Patents for MS513/MX514/MW516
This BenQ projector is covered by the following patents:
U.S. patents 6,837,608; 7,275,834; 7,181,318; TW patents 202690; 205470; I228635;
I259932; China Patents ( 中国发明专利 ) ZL01143168.7; ZL03119907.0;
ZL200510051609.2
Limited warranty
BenQ warrants this product against any defects in material and workmanship, under
normal usage and storage.
Proof of purchase date will be required with any warranty claim. In the event this product
is found to be defective within the warranty period, BenQ's only obligation and your
exclusive remedy shall be replacement of any defective parts (labor included). To obtain
warranty service, immediately notify the dealer from which you purchased the product of
any defects.
Important: The above warranty shall be void if the customer fails to operate the product in
accordance with BenQ's written instructions, especially the ambient humidity must be inbetween 10% and 90%, temperature in-between 0°C and 35°C, altitude lower than 4920
feet, and avoiding to operate the projector in a dusty environment. This warranty gives you
specific legal rights, and you may have other rights which vary from country to country.
For other information, please visit www.BenQ.com.
Copyright
Copyright 2011 by BenQ Corporation. All rights reserved. No part of this publication may
be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any
language or computer language, in any form or by any means, electronic, mechanical,
magnetic, optical, chemical, manual or otherwise, without the prior written permission of
BenQ Corporation.
Disclaimer
BenQ Corporation makes no representations or warranties, either expressed or implied,
with respect to the contents hereof and specifically disclaims any warranties,
merchantability or fitness for any particular purpose. Further, BenQ Corporation reserves
the right to revise this publication and to make changes from time to time in the contents
hereof without obligation to notify any person of such revision or changes.
*DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments. Others
are copyrights of their respective companies or organizations.
Warranty and Copyright information
http://www.pureglare.com.au
72
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement