- Computers & electronics
- Audio & home theatre
- Video switches
- Analog way
- QuickVu QVU150-3G
- Quick start Guide
advertisement
▼
Scroll to page 2
of 4
QUICK START GUIDE QuickVu - Ref. QVU150-3G Thank you for choosing Analog Way and the QuickVu. By following these simple steps, you will be able to set up and use your powerful Dual Scaler Hi-Resolution Seamless Switcher based on Analog Way’s new Midra™ platform within minutes. Discover the QuickVu capabilities and intuitive interface while configuring your first show and unleash your creativity for a new experience in show and event management. WHAT’S IN THE BOX CAUTION! • 1 x QuickVu (QVU150-3G) • 1 x Power supply cord • 1 x Ethernet cross cable (for device update) • 1 x Remote Control Software (RCS²)* • 1 x Set of 6 audio 5-pin screw terminals • 1 x Front Rack Ears (the parts are stowed in the packaging foam) • 1 x User Manual (PDF)* • 1 x Quick Start guide* * User manual, quick start guide and the RCS² are available on www.analogway.com If required, front handles of the device can be dismantled, but with caution. The original screws removed must not be reintroduced to their location without handles in place. Substantial damages can occur, including risk of electric shock from the mains voltage. Only M4x12mm screws can be used. (They are supplied with the unit.) QUICK INSTALL AND SETUP Getting started: You may wish to reset the unit to factory settings to get started. Go to: Menu > Control > Reset/Erase > Default Values > Yes 1. Select the Output resolution that matches the native resolution of your display. You will next be prompted to choose enable follow mode if desired and output rate. Menu > Output > Output format > 1920x1080 > Internal Ref > 60 Hz 2. Inputs can be configured automatically using the Auto Set All function. Menu > Intputs > AutoSet All > Yes It will scan each input and detect the sync type that is plugged in. You can still do an Autoset or manual setup per input. The QuickVu has 2 layers available called: LAYER A and QUICK FRAME. 3. To display a source, select a source (it will blink). Press TAKE to transition your source from Preview to Program output. To view on Preview or change the contents of a different source, simply select it. Only 1 layer can be seen on the Preview. 4. To clear the layer select BLACK. Press TAKE to remove the layer from the Program output. TIP: If you would like the Program and Preview to toggle/ flipflop during each Take, enable this feature by going to Menu > Control > Functions > Preset Toggle. Once enabled, the old Program output will become the new Preview after each Take. 5. See the next page which describes the button lighting color code and other front panel features. QuickVu can be used to display: - sources seamlessly switched in the LAYER A. IMPORTANT: Simply selecting a menu item will not set it to that value. Be sure to press the ENTER button when setting the menu items. Universal Analog Computer/TV/HDTV: inputs #1 to #4 Power supply: 100-240 VAC 2.5A 50/60HZ / FUSE F4A 250 VAC; internal, autoswitchable; 110W On/Off Stand-by: Hold for 3 seconds for stand-by mode Menu scroll knob Input selection: 1 to 4: access source 1 to 4, HDMI 1/2: access HDMI 1 or HDMI 2 SDI 1 to SDI 2: access SDI 1 to SDI 2 S/PDIF: inputs #1 to #2 DVI connectors: DVI-D inputs #1 to #4. Capability to receive digital audio signal from HDMI connector via an adaptator (HDMI-compatible) HDMI connectors: HDMI inputs #3 to #6. Digital audio compliant Ethernet Plug MCO male connector: for inputs (balanced) #1 to #4 Shortcut: Effect: shortcut to transition menu Preset: recall a custom stored preset 3G/HD/SD-SDI: inputs #1 to #2 Control: Exit/Menu: Home menu or back one level Enter: validate the menu or command Front panel display: 4-line VFD Communication port: communication port with a DB9 female connector S/PDIF: outputs #1 to #2 Universal Analog Computer TV/HDTV: outputs #1 to #2 Quick Frame: allows to quickly display a foreground Frame CAUTION: The user should avoid disconnecting the power source (AC input) until the unit is in stand-by mode. DVI connectors: DVI-I outputs #1 to #2. Capability to transmit digital audio signal towards a HDMI connector via an adaptator (HDMI-compatible) Video output connector: 1 x BNC-F: 3G/HD/SD-SDI (with audio embedded) TAKE: Transition the pre-selected sources onto the Program output with the selected effects Layer: Black: clear the output Freeze: freeze the input linked to the current layer on Program MCO male connector: for outputs (balanced) #1 to #2 QUICKVU - REF. QVU150-3G / FRONT & REAR PANELS DESCRIPTION Contextual button Solid orange: 1- Select an input. On the preview screen, the input appears in the layer rectangle 2- Select a transition (open/close) or an effect into Layer menu [Home menu] 3- Press TAKE to view the result on the main screen 4- To remove layer, press BLACK then TAKE 5- For another layer setup, repeat from step #1 1- Press the EXIT/MENU button from the Home menu (all functions must be confirmed by the Enter button) 2- Press Input and Autoset ALL 3- If the acquisition is successful the source appears on Preview. 4- If the acquisition has failed, check all connections and perform a manual setup 5- For a comprehensive Input Setup, please refer to user’s Manual 6- For a manual input setup, press the EXIT/MENU button: a) Press Input, b) Select the right input from Input #1 up to SDI #2, then c) Select Active plug, d) Select Type and choose the input type. 1- Press the EXIT/MENU button from the Home menu (all functions must be confirmed by the ENTER button) 2- Select Output 3- Select Output format and then Output rate 4- On Format line, select the display’s native resolution 5- Control or adjust your display device (Monitor or Video Projector) 6- If necessary, select Test Pattern in the Output menu -O utput 1: select to set the output types and resolutions of Output #1 -O utput 2: select to set the output types and resolutions of Output #2 - I nput: select to configure the 8 individual input types and resolutions - Preset: select to store and use presets - Image: select to change source image settings of an input -K eying/Titling: select to access keying and titling controls and parameters when video layer is selected - S creen: setup your background color and your Quick Frame - L ayer: select to adjust layer size, position, border, transparency or transitions - F rames: select to store (record), use and manage logos and frames into the QuickVu - Audio: select to access all audio input and output parameters -C ontrol: select to access device software information, LAN settings, reset factory settings, amongst other user oriented functions (see next page) R+ R- GROUND(S) R+ R- Outputs #1 and #2: balanced & unbalanced connection Outputs SPDIF #1 and #2: digital audio outputs Output SDI: embedded SDI audio output Inputs # 1 & #2: DVI embedded audio HDMI Inputs #3 & #4: DVI and HDMI embedded audio HDMI Inputs SPDIF #1 and #2: digital audio inputs Inputs HDMI #1 and #2: embedded audio HDMI Inputs SDI #1 to #2: embedded audio SDI BALANCED L+ L- UNBALANCED R+ R- L+ L- L+ L- Left GROUND GROUND Right GROUND MCO male connectors Inputs #1 to #4 : balanced & unbalanced connection AUDIO INPUT/OUTPUT CONNECTIONS NOTE: To adjust layer Size or Pos, use the Layer Menus. To adjust Blanking, use the Auto Centering or Blanking adjustments in the Image menu. INPUT SETUP OUTPUT SETUP FRONT PANEL MENU Layer/source selected or is not currently active on the Program output Blinking green: WORKING WITH THE QUICKVU Layer/source selected or is currently active on the Program output #1 = Source is on Preview #2 = Function available for modification Solid green: Blinking red: #1 = Source is on the Program output #2 = Freeze enable Solid red: BUTTON COLOR USAGE OPERATION OVERVIEW HOW TO DO AN AUTOTAKE? HOME MENU (extract) CONTROL FUNCTIONS AUTOTAKE ENABLED OR DISABLED The Autotake function performs a TAKE automatically each time an input is selected. HOW TO RECORD & DISPLAY A QUICK FRAME? HOME MENU (extract) LOGOS/FRAME RECORD FRAMES FRAME #1 TO #8 The [Empty] term appears next to all unused slots QUICK FRAME: full and individual frame that can be displayed on top of every layer. It is possible to store up to 8 frames in the device non volatile memory. - Select RECORD FRAMES in the frames menu. - A white rectangle will appear on your Program display, indicating the frame which will be caught and saved. (The Frame can be captured in Preview too.) - To select the Quick frame, please go into the SCREEN menu, select QUICK FRAME menu and then choose a Frame slot. The selected frame will be your QUICK FRAME. Now to display it, simply press the front panel button QUICK FRAME. It becomes solid RED. - To remove the QUICK FRAME, press the QUICK FRAME button on the front panel. It becomes solid green. TIP: a long press on the BLACK button will clear all layers on Preview. Press TAKE to view your Program display turn to black. HOW TO DISABLE THE HDCP ENCRYPTION? HOME MENU (extract) INPUTS INPUT # HDMI OR DVI SETTINGS HDCP DETECTION DISABLED HDCP ENABLE ENABLED OR DISABLED HOME MENU (extract) OUTPUT #1 OUTPUT #2 AUTOMATIC The HDCP Encryption can be disabled on HDMI/DVI inputs or/and Program Output #1 / Program Output #2. This can be useful when you have a computer which is detecting the HDCP compliance of your switcher and protecting the content by encrypting the signal from this computer. This feature will disable the HDCP compliance on this specific HDMI/DVI input only. If you want to use HDCP content from your sources, be sure to use only HDCP compliant screens or projector. If it’s not the case, the output image could be disabled. Screen will go to black without displaying the HDCP input image, or partially layer out on HDCP content. The output status can provide you all information about the output in real time. This feature is particularly useful when HDCP is used with long cable to be sure the communication is well handled. HOW TO USE THE AUTO-LOCK FUNCTION? HOME MENU (extract) CONTROL FUNCTIONS AUTO-LOCK ENABLED OR DISABLED AUTO-LOCK allows to select an input only if a signal is valid. WARRANTY AND SERVICE This Analog Way product has a 3 year warranty on parts and labor, back to factory. This warranty does not include faults resulting from user negligence, special modifications, electrical surges, abuse (drop/crush), and/or other unusual damage. In the unlikely event of a malfunction, please contact your local Analog Way office for service. GOING FURTHER WITH THE QUICKVU For complete details and operations procedures, please refer to the QuickVu User’s Manual and our website for further information: www.analogway.com Technical support: Europe, Middle East & Africa Tel.: +33 (0)1 81 89 08 76 [email protected] The Americas Tel.: +1 212 269 1902 [email protected] Asia Pacific Tel.: +65 6292 5800 [email protected] 06/02/2014 - QVU150-3G-QSG Code: 140162
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project