e-Tender no. & Bid Closing date Material
OIL INDIA LIMITED
( A Government of India Enterprise )
P.O. Udayan Vihar -781171
Guwahati, Assam(India)
A. OIL INDIA LIMITED invites Indigenous Competitive Bid under single stage composite bid system
through its e-Procurement portal https://etender.srm.oilindia.in/irj/portal for the following item:
e-Tender no. &
Material Description
Bid Closing date
Procurement, Installation & Commissioning and Training of 5KVA
SGI5018P15
BC
date: UPS for Pump Station SCADA
20.11.2014
Application showing full address/ e-mail address with tender fee (Non-refundable) of Rs. 1000.00 only
(Excepting PSUs and SSI units registered with NSIC) in favour of M/s. Oil India Limited and payable
at Guwahati is to be sent to Chief Materials Manager (PL), Oil India Limited, P.O. Udayan Vihar ,
Assam-781171 only between 10.10.2014 and one week prior to bid closing date. The envelope containing
the application for participation should clearly indicate “Request for participation” for easy identification
and timely issue of authorization. No physical tender documents will be provided. On receipt of requisite
tender fee USER-ID and initial PASSWORD will be communicated to the bidder (through e-mail) and will be
allowed to participate in the tender through OIL’s e-procurement portal. Bidders who are already having
vendor code / user Id are advised to log in using user Id. & password and register against the respective etender and indicate the same while making application along with tender fee for participation. Details of
bidding document can be viewed using “Guest Login” provided in the e-procurement portal. The link to
e-procurement portal has been provided through OIL’s website www.oil-india.com .
B. CORRIGENDUM
Bid Closing Date against E –tender no SGI4028P15 for procurement of stiff telescopic boom truck
mounted hydraulic full slewing crane with hydraulically operated winch has been extended upto
13.11.2014 (upto 11.00 hrs). Application for issue of user id and password will be accepted
upto 07.11.2014 (upto 15.30 hrs). Some changes have been made in the bidding document
(details available in Amendment to tender document in OIL’s e-procurement portal). All
other terms and conditions of the e-tender shall remain unchanged
Page 1 of 17
of tender SGI5018P15 of 30.09.2014
OIL INDIA LIMITED
(A Government of India Enterprises)
PO : Udayan Vihar – 781171
Assam (India)
TELEPHONE NO. (91-361)2643685/688
FAX NO: (91-361) 2643686
Email: panchali@oilindia.in ; erp_mm@oilindia.in
FORWARDING LETTER
Tender No & Date
: SGI5018P15 dated 30.09.2014
Tender Fee
: Rs 1,000.00
Bid Security Amount
: Rs. 26, 400.00
Bidding Type
: SINGLE STAGE COMPOSITE BID SYSTEM
Bid Closing on
: As mentioned in the Basic Data of e-portal
Bid Opening on
:
-do-
Performance Guarantee
:
Applicable
Integrity Pact
: Applicable
OIL invites Bids for Supply, Installation and Commissioning of 5KVA UPS for Pump
Station SCADA through its e-Procurement site under SINGLE STAGE COMPOSITE BID
SYSTEM.
The general details of tender can be viewed by opening the eRFx [Tender] under RFx and
Auctions. The details of items tendered can be found in the Item Data and details uploaded under
Technical RFX. The bidding document is available in the Technical RFx -> External Area - >
Tender Documents
Standard Notes:
1.0 The tender will be governed by “General Terms & Conditions” for e-Procurement as per
Booklet No. MM/LOCAL/E-01/2005 for E-Procurement LCB Tenders.
2.0 This Bidding document consists of :
Technical specifications and Quantity as per Annexure – AAA,
Bid Rejection & Bid Rejection Criteria as per Annexure-BBB
Technical bid check list as per Annexure –EEE ,
Page 2 of 17
of tender SGI5018P15 of 30.09.2014
Response sheet as per Annexure -FFF and
Bank Details as per Annexure-GGG.
Vendor User Manual and LCB Doc Booklet (revised) have been uploaded separately in the
Technical RFx -> External Area - > Tender Documents
3.0 The tender shall also be governed by the Bid Rejection & Bid Evaluation Criteria given in
enclosed Annexure-BBB. However, if any of the Clauses of the Bid Rejection Criteria / Bid
Evaluation Criteria (as per Annexure-BBB) contradict the Clauses of the tender and / or
“General Terms & Conditions” as per Booklet No. MM/LOCAL/E-01/2005 for E-procurement
(LCB Tenders) elsewhere, those in the BEC / BRC shall prevail.
Bidder are advised to fill up the Technical bid check list (Annexure EEE) , Response sheet
(Annexure FFF) and Bank Details (Annexure GGG) given in the bidding document uploaded
in Technical RFx -> External Area - > Tender Documents. The above filled up documents to be
uploaded in the Technical RFX Response.
4.0
5.0 Please do refer the User Manual provided on the portal on the procedure ‘How to create
Response’ for submitting offer.
6.0
Bidders shall prepare and shall upload through electronic form in the OIL’s e-Tender
portal within the Bid Closing Date and Time stipulated in the e-Tender. The “Technocommercial Bid” shall contain all technical and commercial details. Details of prices as per
price format in Appendix-I to be uploaded as attachment in the Attachment Tab “Notes
and Attachments”.
6.1
A screen shot in this regard is given below.
Any offer not complying with above submission procedure will be rejected as per Bid Rejection
Criteria mentioned in the tender.
Go to this Tab “Technical RFx
Response” for Uploading “Technocommercial Bid”.
Go to this Tab “Notes and
Attachments” for Uploading
“Priced Bid” files.
On “EDIT” Mode- The following screen will appear. Bidders are advised to Upload “TechnoCommercial Unpriced Bid” and “Priced Bid” in the places as indicated above:
Page 3 of 17
of tender SGI5018P15 of 30.09.2014
Bid on “EDIT” Mode
Area for uploading TechnoCommercial Bid*
Area for uploading Priced
Bid**
7.0 General Qualification Criteria:
In addition to the General BRC/BEC, following criteria on Bidders' Experience and their
financial capabilities shall be considered (documentary evidence to be provided along with
the bid in Technical RFx -> External Area - > Tender Documents) as on the Bid Closing Date:
i). Successful execution of a single order of value not less than Rs. 7.92 Lakhs for supply of
similar items during last 3 years .
ii). Annual turnover of the firm in any of the last 3 financial years or current financial year
should not be less than Rs. 26.40 Lakhs.
8.0
Application showing full address/email address with Tender Fee (Non-refundable) of
Rs. 1,000.00 in favour of M/s Oil India Limited and payable at Guwahati is to be sent to Chief
Material Manager , Oil India Limited (Pipeline Headquarter ), P.O. Udayan Vihar, Guwahati
-781171. Application shall be accepted only upto one week prior to Bid Closing date. The
envelope containing the application for participation should clearly indicate “REQUEST FOR
ISSUE OF USER ID AND PASSWORD FOR E TENDER NO …” for easy identification and
timely issue of user ID and password. On receipt of requisite tender fee, USER ID and initial
PASSWORD will be communicated to the bidder (through e-mail) and will be allowed to
participate in the tender through OIL’s e- Procurement portal. No physical tender documents
will be provided. Details of bidding document can be viewed using “Guest Login” provided in
the e-Procurement portal. The link to e-Procurement portal has been also provided through
OIL’s web site www.oil-india.com.
NOTE: PSUs and SSI units are provided bidding documents Free of Cost (as per govt
guidelines), however they have to apply to OIL's designated office to issue the tender documents
before the last date of sale of bidding document mentioned in the tender.
9.0 Please note that all tender forms and supporting documents are to be submitted through
OIL’s e-Procurement site only except following documents which are to be submitted manually
in sealed envelope super scribed with Tender no. and Due date to Chief Material Manager ,
Oil India Limited (Pipeline Headquarter ), P.O. Udayan Vihar, Guwahati -781171 on or
before the Bid Closing Date and Time mentioned in the Tender.
a) Original Bid Security
b) Detailed Catalogue (if any)
c) Any other document required to be submitted in original as per tender
requirement
Page 4 of 17
of tender SGI5018P15 of 30.09.2014
All documents submitted in physical form should be signed on all pages by the authorised
signatory of the bidder and to be submitted in triplicate.
10.0 Bidders are requested to examine all instructions, forms, terms and specifications in the
bid.Failure to furnish all information required as per the bidding document or submission of
offers not substantially responsive to the bidding document in every respect will be at the bidders
risk and may result in rejection of its offer without seeking any clarifications.
11.0 Bidders must ensure that their bid is uploaded in the system before the Bid closing date
and time. Also, they must ensure that above documents which are to be submitted in a sealed
envelope are also submitted at the above mentioned address before the bid closing date and time
failing which the offer shall be rejected.
12.0 Bid must be submitted electronically only through OIL’s e-procurement portal. Bid
submitted in any other form will be rejected. All the Bids must be Digitally Signed using “Class
3” digital certificate (e-commerce application) as per Indian IT Act obtained from the licensed
Certifying Authorities operating under the Root Certifying Authority of India (RCAI), Controller
of Certifying Authorities (CCA) of India. The bid signed using other than “Class 3” digital
certificate, will be rejected.
13.0 Any sum of money due and payable to the contractor (including Security Deposit
refundable to them) under this or any other contract may be appropriated by Oil India Limited
and set-off against any claim of Oil India Limited (or such other person or persons contracting
through Oil India Limited) for payment of sum of money arising out of this contract or under any
other contract made by the contractor with Oil India Limited (or such other person or persons
contracting through Oil India Limited).
14.0 In the event of receipt of only a single offer against the tender within B.C. date, OIL
reserves the right to extend the B.C. date as deemed fit by the Company. During the extended
period, the bidders who have already submitted the bids on or before the original B.C. date, shall
not be permitted to revise their quotation.
15.0 To ascertain the substantial responsiveness of the bid OIL reserves the right to ask the
bidder for clarification in respect of clauses covered under BRC also and such clarifications
fulfilling the BRC clauses in toto must be received on or before the deadline given by the
company, failing which the offer will be summarily rejected.
Yours Faithfully
Sd(P.THAKURIA)
DEPUTY MANAGER MATERIALS (PL)
FOR CHIEF MANAGER MATERIALS
(PL)
FOR : GENERAL MANAGER (PLS)
Page 5 of 17
of tender SGI5018P15 of 30.09.2014
ANNEXURE AAA
Item
no.
10
Material Description & Material code No.
Quantity
Unit
Supply of material at Pump Station 1, Duliajan,
Pin-786602) having the following material specification
(Material code: 0C000627)
1
NO.
Technical Specification of 5 KVA / 4.5 KW UPS System
1.
Capacity:
Min 5 KVA / 4.5 KW @ 0.9 p.f.
2.
Technology:
True
On-Line
Double
Conversion UPS with PWM-IGBT technology. UPS
should have both IGBT based Rectifier and IGBT based
Inverter.
3.
Configuration: To
operate
in
Parallel
Redundant Load Sharing configuration. Also to be able to
operate as /in stand alone mode / configuration.
4
Input:
4.1
Phase: Single Phase with Ground
(L-N-G)
4.2
Voltage Range: 180 - 275 V AC,
Single Phase
4.3
Frequency:
50 Hz ± 10 %
4.4
Power Factor:
0.9 or higher
4.5
THDi (Input Current Distortion):
<5 % with full load
5.0
Galvanic Isolation:
Isolation Transformer
for providing galvanic isolation between input & output.
The isolation transformer should be inbuilt and placed
within the UPS cabinet itself. External transformer shall
not be considered.
6.
Output:
6.1
Voltage: 230 V AC, Single phase
6.2
Frequency (Free Running Mode): Within 50
Hz ± 0.25 Hz
6.3
Frequency (Synchronization Range):
Up
to 50 Hz ± 5%
6.4
Voltage Regulation (Both Line and
Load):
Less than ± 1%
6.5
Output waveform:
Pure Sine wave
6.6
THDv
(Total
Harmonic
Distortion):
Less than 5% (non-linear load)
6.7
Crest Factor :
3:1 or better (higher)
6.8
Power Factor:
0.9 or higher.
6.9
Overload Rating: 110 % for 10
minutes (Both minimum)
7.
Efficiency (AC-AC, Inverter and
Converter):
All Minimum 90%
8.1
Transient Voltage:
Dip < 3%,
Peak < 3% of output Voltage
8.2
Transient Recovery:
Within 3 Cycles
9.
Bypass Facility: Both Static &
Manual Bypass
10.
Protections:
Advanced protections for
device safety backed with MCB and fast acting fuses,
high speed pulse blanking, over voltage and under
voltage.
11
Load transfer:
11.1
Inverter to Bypass & Bypass to Inverter:
Page 6 of 17
of tender SGI5018P15 of 30.09.2014
Both < 5 ms
12
Display & Indication :
The UPS should have
a graphical LCD with backlight. It should provide useful
information about the UPS itself with the following
display and indication nominally.
12.1
Measurement: Input voltage, Input current,
Input Frequency, Battery voltage & Level in %, Output
voltage, Output current, Battery Charging / Discharging
current, Output Frequency, Load Level in %, Internal DC
Bus voltage, Internal Temperature etc.
12.2
UPS status:
Operating Mode/ Warning /
Fault / Codes (Faults & Warnings), Normal Mode/ Load
on Bypass mode etc.
12.3
UPS Setting:
Output Voltage / Frequency/
Bypass Enable / Disable etc.
13.
Audible Alarm: Mains Failure alarm / Low
Battery alarm, UPS Warning, Overload, Fault & Bypass
mode etc.
14.1
Enclosure IP and material:
IP21
or
higher.
Material of enclosure is to be steel.
14.2
Enclosure size: Size should nominally be
smaller than the existing UPS which is 660 (H) X 360
(W) X 1030 (D) in mm.
15.
Communication : Network Connectivity: Should
have SNMP hardware and software connectivity facility
for remote monitoring, administration and management
of UPS systems.
16.
Battery brand: The battery should be a
reputed brand having ISO9001:2008 & ISO 14001 : 2004
Certifications for quality & environment.
16.1
Battery Type & Capacity: 12 V VRLA Sealed
Maintenance Free Batteries of requisite capacity to
provide back up time of minimum 30 min at full load.
Capacity calculation for 30 min back up time should be
shown in details.
16.2
Batteries Warranty:
2 Years
minimum.
16.3
Battery Rack: Rack of proper size and
material is to be provided. Size of rack which will be
suitable for the individual site should be confirmed from
customer before supply of the same.
17.
Cold Start Feature:
Should allow UPS to
start on Batteries without utility input.
18.
Environment:
18.1
Ambient Operating Temperature :
0 to 40 deg C
18.2
Relative Humidity :
5% - 90% RH
18.3
Audible Noise : <65 dB @ 1
Meter
19.
Quality:ISO 9001
20.
Compliances to Standards:
20.1
General & safety requirements for UPS used in
operator access areas:
Ensure safety for the operator,
layman & service persons that may come into contact
with the equipment. Compliance to IEC 62040-1-1 or its
equivalent.
20.2
UPS EMC requirements: Ensure satisfactory
functioning in its environment without introducing
intolerable electromagnetic disturbances to other
electronic devices in that environment . Compliance to
IEC 62040-2 or its equivalence.
20.3
RoHS and WEEE:
Compliance to RoHS
Page 7 of 17
of tender SGI5018P15 of 30.09.2014
20
30
40
50
60
70
80
90
100
110
120
130
140
and WEEE.
21. 100 meter of high quality armoured insulated
copper cable of suitable capacity for connecting the
two battery banks at each location at a distance of
about 25 meter from the UPS, is to be supplied along
with the UPS.
22. Supplier to buyback the existing UPS (VINITEC
make 3KVA UPS with 10 nos. of SMF 26 AH batteries
in each UPS ) along with the batteries and should submit
their offer with buyback option.
Material Specification same as that in item no 10 above
without the cable for battery mentioned in specification
sl. No. 21. (For Parallel Redundant Load Sharing
Configuration with that of Item No. 10 above) for PUMP
STATION 1, DULIAJAN,PIN-786602)
Supply of material at Pump Station 2, MORAN, PIN785669 having material specification same as that in item
No. 10.
Material Specification same as that for item No. 10
without the cable for battery mentioned in specification
sl. No. 21. (For Parallel Redundant Load Sharing
Configuration with that of Item No. 30 above) for PUMP
STATION 2, MORAN, PIN-785669
Supply of material at Pump Station 3, JORHAT, PIN785010 having material specification same as that in item
No. 10.
Material Specification same as that in item No. 10
without the cable for battery mentioned in specification
sl. No. 21.(For Parallel Redundant Load Sharing
Configuration with that of Item No. 50 above) for PUMP
STATION 3, JORHAT, PIN-785010.
Supply of material at Pump Station 4, SEKONI, PIN782136 having material specification same as that in item
No. 10.
Material Specification same as that in item No. 10
without the cable for battery mentioned in specification
sl. No. 21.(For Parallel Redundant Load Sharing
Configuration with that of Item No. 70 above) PUMP
STATION 4, SEKONI, PIN-782136.
Supply of material at Pump Station 5, GUWAHATI,
PIN-781171 having material specification same as that in
item No. 10.
Material Specification same as that in item No. 10
without the cable for battery mentioned in specification
sl. No. 21.(For Parallel Redundant Load Sharing
Configuration with that of Item No. 90 above) for PUMP
STATION 5, GUWAHATI, PIN-781171.
Supply of material at Pump Station 6, BONGAIGAON,
PIN-783380 having material specification same as that in
item No. 10.
Material Specification same as that in item No. 10
without the cable for battery mentioned in specification
sl. No. 21.(For Parallel Redundant Load Sharing
Configuration with that of Item No. 110 above) for
PUMP STATION 6, BONGAIGAON, PIN-783380
Supply of material at Pump Station 7, MADARIHAT,
WEST BENGAL, PIN-735220 having material
specification same as that in item No. 10.
Material Specification same as that in item No. 10
without the cable for battery mentioned in specification
sl. No. 21.(For Parallel Redundant Load Sharing
Configuration with that of Item No. 130 above) for
PUMP STATION 7, MADARIHAT, WEST BENGAL,
Page 8 of 17
1
No.
1
No.
1
No.
1
No.
1
No.
1
No.
1
No.
1
No.
1
No.
1
No.
1
No.
1
No.
1
No.
of tender SGI5018P15 of 30.09.2014
150
160
170
180
190
200
210
220
230
240
250
260
270
280
290
300
310
PIN-735220
Supply of material at Pump Station 8, SONAPUR,
WEST BENGAL, PIN-733202 having material
specification same as that in item No. 10.
Material Specification same as that in item No. 10
without the cable for battery mentioned in specification
sl. No. 21.(For Parallel Redundant Load Sharing
Configuration with that of Item No. 150 above for PUMP
STATION 8, SONAPUR, WEST BENGAL, PIN-733202
Supply of material at Pump Station 9, DUMAR, BIHAR,
PIN-854104 having material specification same as that in
item No. 10.
Material Specification same as that in item No. 10
without the cable for battery mentioned in specification
sl. No. 21.(For Parallel Redundant Load Sharing
Configuration with that of Item No. 170 above for PUMP
STATION 9 , DUMAR, BIHAR, PIN-854104.
Supply of material at Pump Station 10 , BARAUNI,
BIHAR, PIN-851114 having material specification same
as that in item No. 10.
Material Specification same as that in item No. 10
without the cable for battery mentioned in specification
sl. No. 21.(For Parallel Redundant Load Sharing
Configuration with that of Item No. 190 above for PUMP
STATION 10 , BARAUNI, BIHAR, PIN-851114.
Installation and Commissioning at PS-1, DULIAJAN,
ASSAM, PIN-786602 and dismantling of old UPS and
batteries from site.
Installation and Commissioning at PS-2, MORAN,
ASSAM, PIN-785669 and dismantling of old UPS and
batteries from site.
Installation and Commissioning at PS-3, JORHAT,
ASSAM, PIN-785010 and dismantling of old UPS and
batteries from site.
Installation and Commissioning at PS-4, SEKONI,
ASSAM, PIN-782136 and dismantling of old UPS and
batteries from site.
Installation and Commissioning at PS-5, GUWAHATI,
ASSAM, PIN-781171 and dismantling of old UPS and
batteries from site.
Installation
and
Commissioning
at
PS-6,
BONGAIGAON and OIL’s Terminal at BRPL ASSAM
and dismantling of old UPS and batteries from site.
Installation and Commissioning at PS-7, MADARIHAT,
WEST BENGAL, PIN-735220 and dismantling of old
UPS and batteries from site.
Installation and Commissioning at PS-8, SONAPUR,
WEST BENGAL, PIN-733202 and dismantling of old
UPS and batteries from site.
Installation and Commissioning at PS-9, DUMAR,
BIHAR, PIN-854104 and dismantling of old UPS and
batteries from site.
Installation and Commissioning at PS-10, BARAUNI,
BIHAR, PIN-851114 and dismantling of old UPS and
batteries from site.
Material specification same as that for Item No. 10
except buyback as mentioned in serial no. 22 and except
that battery Capacity should be for a back up time of 4
(Four) hours each and warranty for the supplied batteries
should be 3 (three years). The two units are for Parallel
Redundant Load Sharing Configuration.
(Tengakhat Pump Station, Dibrugarh district, Assam,
Page 9 of 17
1
No.
1
No.
1
No.
1
No.
1
No.
1
No.
1
AU
1
AU
1
AU
1
AU
1
AU
1
AU
1
AU
1
AU
1
AU
1
AU
2
No.
of tender SGI5018P15 of 30.09.2014
PIN-786103)
Installation and Commissioning at Tengakhat Pump
Station, Dibrugarh district, Assam, PIN-786103.
320
1
AU
NOTE:
1. Installation and commissioning: Supplier has to install and commission the UPS and batteries at all the required
places namely PS1 (Duliajan, Assam), PS2 (Moran, Assam), PS3 (Jorhat, Assam), PS4 (Sekoni, Assam), PS5
(Guwahati, Assam), PS6 (Bongaigoan, Assam), PS7 (Madarihat, West Bengal), PS8 (Sonapur, West Bengal), PS9
(Dumar, Bihar), PS10 (Barauni, Bihar) and Tengakhat, Assam. All materials required for installation of UPS and
batteries to be provided by the supplier including proper armoured cable for batteries which may have to be installed
at an average of 25 meters away from the UPS units.
2. Test Certificates from government recognised testing agency should be submitted for the quoted product
confirming the technical specification parameters.
3. Pre- Despatch Inspection and Testing: Supplier will provide facility for inspection & testing of UPS and
batteries by OIL personnel before dispatch and inform at least two weeks in advance.
4. Training : Supplier has to give training as detailed below.
(i)During installation at each site, minimum half day training to the OIL personnel of the site (Pump Station) on
Operation and Maintenance of the UPS to be supplied.
(ii)Minimum one-day class room training at each of these Base Stations viz. PS3 (Jorhat, Assam), PHQ
(Guwahati, Assam) and PS8 (Sonapur, West Bengal) and at Pump Station PS1(Duliajan, Assam)
explaining full operation, logic, operating and maintenance procedures of the UPS to be supplied by competent
personnel(s) of the supplier/ OEM at mutually agreeable dates. OIL will provide only the class room facility for
this.
5. Buyback of old UPS and batteries (for Pumpstation 1 to Pumpstation 10 (except Tengakhat Pump Station
as mentioned in item no. 310 above): Presently there are 20 nos. of VINITEC make 3KVA UPS with 10 nos. of
SMF 26 AH batteries in each UPS. They are at different locations / Pump station from Duliajan in Assam to Barauni
in Bihar. Supplier to buyback the existing UPS from different locations along with the batteries and should
submit their offer with buyback option. Parties have to make their own arrangement of dismantling and collection
of the old UPS and batteries from the respective locations after installation of the new one. Supplier to make their
own arrangement for disposal of the old batteries following Pollution Control Board guidelines and Environment
Protection Act 1986. Supplier should deposit proof of disposal done as per the guidelines and Act.
6. Documentation: Two sets of complete documentation including block diagram, detail description of UPS system,
card level description, component level circuit diagram of UPS system and electronic cards, fault diagnosis
procedure & rectification will be provided by the manufacturer for each unit.
7. Maintenance spares: Suppliers to quote for the minimum required maintenance spares optionally, which will
not be considered for price comparison of the main UPS and purchase of which will be at OIL’s discretion.
8. Warranty: Onsite warranty of minimum one year after installation and commissioning of UPS to be provided by
the supplier.
9. Annual Maintenance Contract: Supplier to provide on-site Comprehensive AMC services of the UPS after
expiry of the warranty for a period of minimum 5 (five) years. Charges of the comprehensive on-site Annual
Maintenance Contract of the UPS is to be quoted by the supplier which will be considered for price comparisons
but for which a separate contract agreement will be entered into at the quoted rate after expiry of the
warranty period.
10. All materials supply, Installation and Commissioning charges to be made at sites as mentioned above. Supplier
to quote freight charges, Installation and Commissioning charges accordingly.
*******************
Page 10 of 17
of tender SGI5018P15 of 30.09.2014
ANNEXURE BBB
Bid Rejection Criteria (BRC) & Bid Evaluation Criteria (BEC)
1.0 BID REJECTION CRITERIA (BRC)
The bid shall conform generally to the specifications and terms and conditions given in this bidding document. Bids
shall be rejected in case the goods/materials offered do not conform to required parameters stipulated in the
technical specifications. Notwithstanding the general conformity of the bids to the stipulated specifications, the
following mandatory requirements will have to be particularly met by the Bidders without which the same will be
considered as non-responsive and rejected. All the documents related to BRC must be uploaded along with the
Technical Bid.
(A)
Technical
The Bidder must meet the following requirements:1. Bidder should be Original Equipment Manufacturer (OEM) of the UPS system.
OR
Bidder should be an authorized dealer / service provider of the UPS system. Authorized dealer / service provider
shall submit documentary evidence of authorization from the OEM, along with their bid.
2. Bidder should have a fully equipped service centre and office at Guwahati and should be able to provide
maintenance service within 3 working days from the receipt of complain through email / fax etc in all the pump
stations from PS1 (Duliajan) to PS10 (Barauni). Bidder must confirm this in their bid.
3. Bidder should have the experience of successfully supplying, commissioning and maintaining at least 5 nos. of
UPS systems in a single order of at least 3KVA or above within the last seven years from Bid Closing Date of this
bidding document.
4. Bidder must undertake and confirm from OEM that provisioning of spares and maintenance service should be
available for at least next 7 years.
5. Manufacture of the UPS should be in accordance to international quality standard ISO 9000 series of standard, for
which the manufacturer should be duly certified under ISO 9001 quality certification.
6. Test Certificates from government recognised testing agency should be submitted for the quoted product
confirming the technical specification parameters.
(B)
COMMERCIAL :
i) The Bidder shall furnish requisite Bid Security by way of a Bank Guarantee/Bank Draft in the manner and as
specified in Section ‘Bid Security’ which shall be furnished along with the Bid. Any bid not accompanied by a
proper bid security will be rejected.
ii) Validity of the bid shall be minimum 120 days from the Bid Closing Date, otherwise the bid shall be rejected.
iii) The prices offered will have to be firm through delivery and not subject to variation on any account. A bid
submitted with an adjustable price will be treated as non-responsive and rejected.
iv) Bids received after the bid closing date and time will be rejected.
v) All the Bids must be Digitally Signed using #Class 3# digital certificate (e-commerce application) as per Indian
IT Act obtained from the licensed Certifying Authorities operating under the Root Certifying Authority of India
(RCAI), Controller of Certifying Authorities (CCA) of India. The bid signed using other than #Class 3# digital
certificate, will be rejected.
Page 11 of 17
of tender SGI5018P15 of 30.09.2014
vi) The User ID & Password are not transferable. Bids submitted by parties to whom the User ID & Password was
not issued by the Company will be rejected.
vii)
Conditional offers will be rejected.
viii)
Bids received in any form or media other than through OIL’s e-Procurement portal will not be accepted.
ix)
Bid documents uploaded in the e-Procurement Portal shall be typed/written and scanned clearly and contain
no inter lineation, erasures or overwriting except as necessary to correct errors made by bidder, in which case such
corrections must be initialed by the person(s) signing the bid. Any bid not meeting this requirement shall be rejected.
x) Bidder must accept and comply with the following clauses as given in the Bidding document in toto, failing
which offer will be rejected:
a.
b.
c.
d.
e.
Performance Bank Guarantee clause
Force Majeure Clause
Tax Liabilities clause
Arbitration clause
Liquidated damage clause
C. GENERAL:
i) In case bidder takes exception to any clause of Bidding Document not covered under
BEC/BRC, then the Company has the discretion to load or reject the offer on account of such exception if the
bidder does not withdraw/modify the deviation when/as advised by the Company. The loading so done by the
Company will be final and binding on the Bidders. No deviation will however, be accepted in the clauses
covered under BRC.
ii) In case any of the clauses in the BRC contradict with other clauses of Bidding Document
elsewhere, then the clauses in the BRC will prevail.
iii) Any exceptions/deviations to the Bidding Document and applicable statutory duties and levies
must be spelt out by bidder in their bid only.
iv) The originals of such documents (furnished by bidder(s)) shall have to be produced by
bidder(s) to OIL as and when asked for.
2.0 BID EVALUATION CRITERIA (BEC):
i) The bids confirming to the technical specifications, terms and conditions stipulated in the bidding documents and
considered to be responsive after subjecting to Bid Rejection Criteria will be considered for further evaluation as per
the Bid Evaluation Criteria.
ii) To evaluate the inter-se-ranking of the offers, Assam entry tax on purchase value will be loaded as per prevailing
Govt. of Assam guidelines as applicable on bid closing date. Bidders may check this with the appropriate authority
while submitting their offer.
iii) Other terms and conditions of the enquiry shall be as per General Terms and Conditions vide MM/LOCAL/E01/2005 for E-Procurement LCB Tenders. However, if any of the Clauses of the Bid Rejection Criteria / Bid
Evaluation Criteria (BRC / BEC) contradict the Clauses of the Bidding document or MM/LOCAL/E-01/2005
elsewhere, those in the BRC / BEC shall prevail.
iv) To ascertain the inter-se-ranking, the comparison of the responsive bids will be made as per price format given
in Appendix-I.
Page 12 of 17
of tender SGI5018P15 of 30.09.2014
Appendix-I
Bidders are required to submit the summary of the prices in their commercial bids as per bid format
(Summary), given below :
Priced Bid Format ( SUMMARY ):
Sl.
No.
1
2
3
4
5
Material Description & Material code No.
Qty.
Unit
Cost of 5 KVA / 4.5 KW UPS System without the cable for
battery mentioned in specification sl. No. 21. (Details as in
technical specification of item no. 10 in Annexure AAA)
20
Nos.
Cost of 5 KVA / 4.5 KW UPS System without the cable for
battery mentioned in specification sl. No. 21. (Details as in
technical specification Item no. 310 in Annexure AAA)
100 meter of high quality armoured insulated copper cable of
suitable capacity for connecting the two battery banks at each
location at a distance of about 25 meter from the UPS, is to be
supplied along with the UPS.
Installation and Commissioning charges including dismantling
and collection of the old UPS and batteries from the respective
locations as mentioned in Item nos. 210 to 300 of Annexure
AAAabove.
Installation and Commissioning charges as mentioned in Item no.
320 in Annexure AAA above
02
Nos.
12
(1 no. of
100
meters)
10
No.
1
AU
(A)
(B)
(C)
(D)
(E)
(F)
(G)
(H)
(I)
(J)
(K)
(L)
(M)
(N)
(O)
(P)
(Q)
(R)
(S)
(T)
Unit
Price
Total
Price
AU
Total material value ( as in Serial no. 1, 2 and 3 above)
Packing and Forwarding Charges
Total Ex-works value ( A+B)
Excise Duty including Cess, (Please indicate applicable rate of Duty)
Total Ex-works value including Excise Duty & Cess (C+D)
Sales Tax, (Please indicate applicable rate of Tax)
Total FOR Despatching station value ( E+F)
Transportation charges to sites (Lumpsum)
Transit Insurance Charges
Inter State Entry tax
Total FOR Destination value (G+H+I+J)
Pre-despatch inspection and testing Charges (Lumpsum)
Total Installation and Commissioning charges (Lumpsum)
(item nos. 210 to 300 and 320 of Annexure AAA)
Service tax on Commissioning charges, if any
(please indicate the percentage)
Training Charges (Lumpsum)
Service tax on Training charges, if any
(please indicate the percentage)
Buy Back Price of old Batteries inclusive of taxes, (Presently there are 20 nos. of
VINITEC make 3KVA UPS with 10 nos. of SMF 26 AH batteries in each UPS)
AMC charges (Lumpsum)
Service Tax on AMC Charges:
(please indicate the percentage)
Total Value for evaluation of offer (K+L+M+N+O+P +R+S-Q)
Page 13 of 17
of tender SGI5018P15 of 30.09.2014
(U)
(V)
(W)
Total value in words :
Gross Weight :
Gross Volume :
1.0
Pre-despatch Inspection charges and testing charges, Installation &Commissioning
charge and Training Charges must be quoted separately (not to include in materials
cost) which shall be considered for evaluation of the offers. These charges should
include amongst others to and fro fares, boarding/lodging, local transport and other
expenses of supplier’s commissioning personnel during their stay at the site. In
case, Installation & commissioning charge is different for different sites, to quote
site wise separately.
2.0
Bidders must categorically indicate the Pre-despatch Inspection charges , testing
charges Installation & Commissioning charges & Training charges in their offers
as mentioned in Price format in Appendix I above and must confirm about
providing the same in their bids. In case Pre-despatch Inspection charges, testing
charges, Installation & Commissioning charges and training charges are
NIL/inclusive, bidder must categorically mention the same in their offer. Please
note that if these charges are not quoted separately, it will be considered as
inclusive. In case, you mention that these charges are extra and donot quote these
charges separately, your offer will be considered as incomplete and will be rejected.
3.0
All materials, pre-despatch inspection, testing, Installation & Commissioning and
Training to be procured from same source.
*************
Page 14 of 17
of tender SGI5018P15 of 30.09.2014
Tender No.
SGI5018 P15 dated 30.09.2014
Annexure
EEE
Matrix for Technical & Commercial
Evaluation
Note :- Only Grey coloured boxes are to be
filled by the bidder
Name of Bidder :
Compliance by Bidder
SL. NO.
1
BEC / TENDER REQUIREMENTS
Bidder to confirm that they have not taken
any exception/deviations to the bidding
document .
Indicate 'Confirmed' /
'Not Confirmed' / Not
applicable
2
Confirm that the product offered strictly
conform to the technical specifications.
3
4
5
6
Confirm that the Offer has been made with
Bid Security along with the offer ?
Confirm unconditional validity of the bid
for 120 days from the date of opening of
techno-commercial bid.
Confirm that the prices offered are firm.
Conditional offer will be liable for
rejection?
Confirm that all relevant fields in the online biding format been filled in by the
bidders for the items quoted by them.
7
8
9
10
Confirm that the price bid is in conformity
with OIL’s online bidding format ?
Confirm that the Bid comply with all the
terms & conditions ?
Confirm that the offers and all attached
documents are digitally signed using digital
signatures issued by an acceptable
Certifying Authority (CA) as per Indian IT
Act 2000.
CONFIRM THAT YOU HAVE SHALL
SUBMIT PERFORMANCE BANK
GUARANTEE AS PER bidding document
IN THE EVENT OF PLACEMENT OF
ORDER ON YOU
Page 15 of 17
of tender SGI5018P15 of 30.09.2014
Indicate
Corresponding
page ref. of bid
Annexure FFF
Bidders Response Sheet
Sl
No.
1
2
3
4
Description
Remarks
Name of Bidder
Place of Despatch (Ex- Works)
Whether Freight charges have been included in your quoted
prices
Whether Transit Insurance charges have been included in your
quoted prices
5
6
7
Make of quoted Product
Offered Validity of Bid from Bid Closing Date
Delivery Period in days/weeks/months from placement of
order
8
Complied to Standard Payment Terms of OIL or not.
(Please refer to clause 23.2 of LCB Doc Booklet)
Bid Security Submitted (if applicable)
Details of Bid Security Submitted to OIL (if applicable)
a) Bid Security Amount (In Rs):
b) Bid Security Valid upto:
c) Name and Full Address of Issuing Bank:
Confirm that the Bid Security submitted (In case of Bank
Guarantee) is in toto as per format provided in the bidding
document.
Bid Security if Not submitted, reasons thereof
9
10
11
12
13
14
15
Whether you shall submit Performance Security in the event of
placement of order on you.
Whether submitted documents in support of General
qualification criteria of bidding document.
If bidder is Small scale unit whether you have quoted your own
product.
If bidder is Small scale unit , whether you are owned by SC/ST
entrepreneur.
Page 16 of 17
of tender SGI5018P15 of 30.09.2014
ANNEXURE - GGG
(TO BE FILLED UP BY ALL THE VENDOR IN THEIR OWN LETER HEAD)
(ALL FIELDS ARE MANDATORY)
Tender No.
Name of Beneficiary
Vendor Code
:……………………………………………………………………
:M/s……………………………………………………………………
:………………………………………………………………………...
Address
:..……………………………………………………………………….
..………………………………………………………………………..
Phone No. (Land Line)
:..……………………………………………………………………….
Mobile No.
:..……………………………………………………………………….
E-mail address
:..……………………………………………………………………….
Bank Account No. (Minimum
Eleven Digit No.)
:..……………………………………………………………………….
Bank Name
:..……………………………………………………………………….
Branch
:..……………………………………………………………………….
Complete Address of your
:..……………………………………………………………………….
Bank
:..……………………………………………………………………….
IFSC Code of your Bank
a) RTGS
:………………………………………………………………………...
b) NEFT
:………………………………………………………………………...
PAN
:………………………………………………………………………...
VAT Registration No.
:………………………………………………………………………...
CST Registration No.
:………………………………………………………………………...
Service Tax Registration No.
:………………………………………………………………………...
Provident Fund Registration
:………………………………………………………………………...
I/We confirm and agree that all payments due to me/us from Oil India Limited can be remitted to
our above mentioned account directly and we shall not hold Oil India Limited responsible if the
amount due from Oil India Limited is remitted to wrong account due to incorrect details furnished
by us.
………………………………
Office Seal
Signature of Vendor
Counter Signed by Banker:
Seal of Bank:
Enclosure: Self attested photocopies of the following documents1)
2)
3)
4)
5)
6)
7)
PAN Card
VAT Registration Certificate
Service Tax Registration
CST Registration
Provident Registration Certificate
Cancelled cheque of the bank account mentioned above (in original).
Bank Statement not older than 15 days on the date of submission.
Page 17 of 17
of tender SGI5018P15 of 30.09.2014
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising