Advertisement
Advertisement
1-800-779-2102
DZ 960050B
Mon - Thurs 7:30am - 5:00pm | Friday 7:30am - 4:00pm CST
PLEASE INSPECT YOUR PRODUCT FOR DAMAGE
BEFORE PROCEEDING TO INSTALLATION
INSTRUCTIONS FOR RETURNS:
ALL PRODUCTS NEED RETURNED TO THE ORIGINAL POINT OF
PURCHASE FOR RETURNS, WARRANTY DEFECTS, OR DAMAGE.
FOR MISSING HARDWARE & PARTS,
PLEASE CONTACT DEE ZEE DIRECTLY.
WWW.DEEZEE.COM
REGISTER YOUR PRODUCT ONLINE: www.deezee.com/registration
VIEW INSTRUCTIONS ONLINE: www.deezee.com/instructions
Page 1 of 24
04/18/18
Thank you for choosing Dee Zee to add function and accessorize your vehicle. Dee Zee has been a staple brand in the truck accessory market since 1977 and we hold a reputation of quality manufacturing based in America’s Heartland. Our products are born through careful engineering and backed by industry leading warranty programs. We appreciate the opportunity to serve you and your vehicle!
Review the instruction pages in their entirety to prepare the required tools
Note: This product is an appearance accessory and should not be relied upon as protection for the vehicle occupants in the event of an accident. Buyer assumes all risk, liability, and costs for vehicle impact operations.
Any modifications or unintended use of this product shall immediately void all manufacturers’ warranties. Dee Zee, Inc. disclaims all liability for injuries to persons or property resulting from modifications or unintended use of this product.
You can review the full warranty policy at www.deezee.com.
Cleaning: To be entitled to all warranty rights offered with the product, Dee Zee sport bars need to be cleaned regularly with a mild detergent. Do NOT use abrasive cleaners.
DZ 960050B
Page 2 of 24
04/18/18
A Front Bar
Sport Bar DZ 960050B
Installation Instructions
B Back Bar C Top Bracket
D Bed Bracket
G Rear Brake Light
X1
E
Driver Side Plate
X2
H
Rubber Boot
X1
F
Passenger Side Plate
X1
X1
I
Rubber Grommet
X1
J 4mm Allen Head
Bolt
X1
K 4mm Lock
Washer
X2
N 8mm Flat Washer O Steel block
X2
X4
L
4mm Flat
Washer
P 8mm Lock
Washer
X2
X3
M 8mm Allen Head
Bolt
X2
Q 8mm Nut
DZ 960050B
X4
X2
Page 3 of 24
X2 X2
04/18/18
R 12mm -1.75
Flat Socket
Bolt
V
6mm Nut
S 6mm Allen Head
Bolt
T
6mm Lock Washer
U
6mm Flat Washer
X4
W 12mm Welded
Bolt
X10 X10
X
12mm Flat Washer
Y
12mm Lock
Washer
X20
Z
12mm Nut
X10 X4
AA 12mm Rubber
Cover
AB
12mm Plastic
Washer
X4
X4 X4
Tools Required
X8
Allen Wrench
SUPPLIED
Ratchet and Socket or Wrench
10mm
13mm
Drill
1/2” Drill Bit
DZ 960050B
Page 4 of 24
X4
04/18/18
1
Install the rubber grommet (I) in the back bar (B) then feed the wires for the third brake light though the grommet. Then install the third brake light (G) using bolt (J), lock washer (L) and lock washer (K). Fully tighten hardware. Install rubber grommets (I) into the front bar (A) as shown.
L
K J
G B
I
A
2
Next the front bar (A) and the rear bar (B) need to come together. The rear bar tabs will go underneath the front bar tabs. Place the steel blocks (O) on top of the tabs then install the top bracket (C). Use bolts (M), washers (N), lock washers (P) and nuts (Q) to secure the front bar, rear bar, and top bracket together. Center top bracket and Fully tighten hardware.
B
DZ 960050B
A
Page 5 of 24
N
P
Q
M
N
C
O
04/18/18
DZ 960050B
3 Feed the wires from the third brake light to the upper hole of the front bar where the grommet was installed in step 1. Run the wires into the front bar, down to the lower hole of the front bar and bring the wires out of the lower hole.
4
Wires come out here
Wires coming through rear bar
Wires go into front bar
Wires in front bar
Install rubber boots (H) on the ends of the front and rear bars. Then install the bed brackets (D) using bolts (R). Bends on the bed brackets are on the outside of the sport bar and facing down. Do not fully tighten hardware at this time.
Page 6 of 24
R
H
D
04/18/18
5 Install driver side plate (E) by using bolts (S), lock washers (T) flat washers (U) and nuts (V). Then repeat on passenger side using the passenger side plate (F). Fully tighten hardware.
E
S
T
U
V
U
6
Place the sport bar assembly on the bed and adjust the bed brackets to desired position. Mark the bed caps in the inner slots of the bed brackets to locate where the holes need to be drilled. Remove the sport bar and fully tighten the bed brackets to the front and rear bars
DZ 960050B
Page 7 of 24
04/18/18
7 Drill holes in the middle of the marks that were made in step 6. Once the holes are drilled, place the sport bar back onto the truck bed and line up the holes with the slots.
Drill Holes
8
Install sport bar assembly using bolts (W), plastic washers (AB), washers (X), lock washers (Y) and nuts (Z). Center the sport bar and fully tighten hardware at this time.
Then install the rubber cover (AA) onto nut (Z).
Z
Y
X
Z
AA
DZ 960050B
Page 8 of 24
04/18/18
Sport Bar Wiring Instructions
Find your make and model year then go to the page listed. For the most recent revision of color instructions visit www.deezee.com/instructions/
Make Year Go to Page
Chevy/GMC
Chevy/GMC
1999-2007
2007-2013
10
12
Chevy/GMC
Ford F150
Ford F150
2014+
2009-2014
2015+
Nissan Titan 2017+
Toyota Tundra 2007-2016
14
16
18
21
23
A
¼” Eyelet
X1
D Mini Add-A-Fuse (Bigger)
X1
G Zip-ties and wire loom
E
B
Sport Bar Wiring
Hardware
3/8” Eyelet
X1
Micro Add-A-Fuse
(Smaller)
X1
Tools Required
Wire Crimper
C Scotch lock
F
10 amp Micro and Mini fuses
X1 X1
Wire Stripper
X1
X8
DZ 960050B
X15 Ft
Page 9 of 24
04/18/18
Chevy/GMC 1999-2007 Wiring Instructions
1 Run the Red wire of the CHMSL light through the stake pocket and back to the driver side brake light. Remove the brake light and locate the Blue wire in the top light socket.
Blue wire
2 Run the Black wire of the CHMSL light through the stake pocket down towards the frame of the truck and locate the ground bolt as shown.
Bolt
DZ 960050B
Page 10 of 24
04/18/18
3 Use the scotch lock (C) to connect the Blue wire of the tail light and the Red wire of the
CHMSL light. Insert the Blue wire into the outer slot of the scotch lock and insert the
Red wire into the blunt end of the Scotch lock. Then fold over the plastic cover and crimp the Scotch lock together.
Red wire
C
Blue wire
Open Closed
4 Strip the end of the Black wire of the CHMSL light and crimp the ¼” eyelet (A) onto the
Black wire. Remove the ground bolt from step 2 and add the eyelet. Reinstall the bolt.
Black wire
A
Use Wire Loom (G) and Zip-ties (G) to cover and hold up wires where preferred.
DZ 960050B
Page 11 of 24
04/18/18
Chevy/GMC 2007-2013 Wiring Instructions
1 Run the Red wire of the CHMSL light through the stake pocket towards the frame and run the wire up to the fuse box under the hood. Remove the fuse box cover and locate the CHMSL fuse.
2 Run the Black wire of the CHMSL light through the stake pocket down towards the frame of the truck and locate the ground bolt as shown.
Bolt
DZ 960050B
Page 12 of 24
04/18/18
3 Remove the CHSML fuse and install the Mini Add-A-Fuse (D) in its place reinstall the original fuse into the bottom slot of the Add-A-Fuse. Strip and crimp the Red wire into the wire coming out of the Add-A-Fuse and add a 10 amp Mini fuse (F) into the top slot of the Add-A-Fuse.
New Fuse
D F
Original
Fuse
Red Wire
4 Strip the end of the Black wire of the CHMSL light and crimp the ¼” eyelet (A) onto the
Black wire. Remove the ground bolt from step 2 and add the eyelet. Reinstall the bolt.
Black wire
A
After done wiring, confirm the third brake light works. If it does not light up turn the Add-A-Fuse 180 degrees around in the Fuse box.
Use Wire Loom (G) and Zip-ties (G) to cover and hold up wires where preferred.
DZ 960050B
Page 13 of 24
04/18/18
Chevy/GMC 2014-Current Wiring Instructions
1 Run the Red wire of the CHMSL light through the stake pocket towards the frame and run the wire up to the fuse box under the hood. Remove the fuse box cover and locate the CHMSL fuse.
2 Run the Black wire of the CHMSL light through the stake pocket down towards the frame of the truck and locate the ground bolt as shown.
Bolt
DZ 960050B
Page 14 of 24
04/18/18
3
Original
Fuse
Remove the CHSML fuse and install the Micro Add-A-Fuse (E) in its place reinstall the original fuse into the bottom slot of the Add-A-Fuse. Strip and crimp the Red wire into the wire coming out of the Add-A-Fuse and add a 10 amp Micro fuse (F) into the top slot of the Add-A-Fuse.
New Fuse
D
F
Red Wire
4 Strip the end of the Black wire of the CHMSL light and crimp the ¼” eyelet (A) onto the
Black wire. Remove the ground bolt from step 2 and add the eyelet. Reinstall the bolt.
Black wire
A
After done wiring, confirm the third brake light works. If it does not light up turn the Add-A-Fuse 180 degrees around in the Fuse box.
Use Wire Loom (G) and Zip-ties (G) to cover and hold up wires where preferred.
DZ 960050B
Page 15 of 24
04/18/18
Ford F-150 2009-2014 Wiring Instructions
1 Run the Red wire of the CHMSL light through the stake pocket towards the frame and run the wire up under the hood. Locate the Blue with Orange Stripe wire that is between the coolant tank and the firewall, it is taped to a main wire loom.
2 Run the Black wire of the CHMSL light through the stake pocket down towards the frame of the truck and locate the ground bolt as shown.
Bolt
DZ 960050B
Page 16 of 24
04/18/18
3
Use the scotch lock (C) to connect the Blue with Orange Stripe wire and the Red wire of the CHMSL light. Insert the Blue with Orange Stripe wire into the outer slot of the scotch lock and insert the Red wire into the blunt end of the Scotch lock. Then fold over the plastic cover and crimp the Scotch lock together.
Red wire
Blue with
Orange
Stripe
C
Open Closed
4 Strip the end of the Black wire and crimp the 3/8” eyelet (B) onto the Black wire.
Remove the ground bolt from step 2 and add the eyelet. Reinstall the bolt.
B
Black wire
Use Wire Loom (G) and Zip-ties (G) to cover and hold up wires where preferred.
DZ 960050B
Page 17 of 24
04/18/18
Ford F-150 2015-Current Wiring Instructions
1 Run the Red wire of the CHMSL light through the stake pocket towards the frame and run the wire up under the hood. Run the wire through the firewall by cutting the zip tie on the rubber boot where the main wire loom goes through the firewall.
Cut zip tie
2 Remove the Driver side kick panel by first pulling straight up on the piece that is shown.
Pull up
DZ 960050B
Page 18 of 24
04/18/18
3 Remove the Driver side kick panel by pulling up towards the bottom then pulling towards the rear of the vehicle.
Then Pull
Rearward here
Pull up here first
4 Locate the Purple with a White Stripe wire in the Black Plug. Insert the Purple with White
Stripe wire into the outer slot of the scotch lock (C) and insert the Red wire into the blunt end of the Scotch lock. Then fold over the plastic cover and crimp the Scotch lock together. Then reinstall the driver side kick panel and the top piece.
Red
Purple wire with
White
Purple with Stripe
White Stripe
C
Open
Closed
DZ 960050B
Page 19 of 24
04/18/18
5 Run the Black wire of the CHMSL light through the stake pocket down towards the frame of the truck and locate the ground bolt as shown.
Bolt
6 Strip the end of the Black wire of the CHMSL light and crimp the 3/8” eyelet (B) onto the
Black wire. Remove the ground bolt from step 5 and add the eyelet. Reinstall the bolt.
Black wire
B
Use Wire Loom (G) and Zip-ties (G) to cover and hold up wires where preferred.
DZ 960050B
Page 20 of 24
04/18/18
Nissan Titan 2017-Current Wiring Instructions
1 Run the Red wire of the CHMSL light through the stake pocket and back to the driver side brake light. Remove the brake light and locate the Red wire in the top light socket.
2 Run the Black wire of the CHMSL light through the stake pocket down towards the frame of the truck and locate the ground bolt as shown.
Bolt
DZ 960050B
Page 21 of 24
04/18/18
3 Use the scotch lock (C) to connect the Red wire of the tail light and the Red wire of the
CHMSL light. Insert the Red wire of the Tail light into the outer slot of the scotch lock
(C) and insert the Red wire of the CHMSL light into the blunt end of the Scotch lock.
Then fold over the plastic cover and crimp the Scotch lock together.
Red wire of the Tail
Light
C
Red wire
CHMSL light
Open
Closed
4 Strip the end of the Black wire of the CHMSL light and crimp the 3/8” eyelet (B) onto the
Black wire. Remove the ground bolt from step 2 and add the eyelet. Reinstall the bolt.
Black wire
B
Use Wire Loom (G) and Zip-ties (G) to cover and hold up wires where preferred.
DZ 960050B
Page 22 of 24
04/18/18
Toyota Tundra 2007-2016 Wiring Instructions
1 Run the Red wire of the CHMSL light through the stake pocket and back to the driver side brake light. Remove the brake light and locate the Red wire in the bottom light socket.
Red wire
2 Run the Black wire of the CHMSL light through the stake pocket down towards the frame of the truck and locate the ground bolt as shown.
Bolt
DZ 960050B
Page 23 of 24
04/18/18
3 Use the scotch lock (C) to connect the Red wire of the tail light and the Red wire of the
CHMSL light. Insert the Red wire of the Tail light into the outer slot of the scotch lock
(C) and insert the Red wire of the CHMSL light into the blunt end of the Scotch lock.
Then fold over the plastic cover and crimp the Scotch lock together.
C
1
Red wire
CHMSL light
Red wire of the Tail
Light
Open Closed
4 Strip the end of the Black wire of the CHMSL light and crimp the 3/8” eyelet (B) onto the
Black wire. Remove the ground bolt from step 2 and add the eyelet. Reinstall the bolt.
Black wire
B
Use Wire Loom (G) and Zip-ties (G) to cover and hold up wires where preferred.
DZ 960050B
Page 24 of 24
04/18/18

Public link updated
The public link to your chat has been updated.
Advertisement