GIGABIT ROUTER WIRELESS 300N

GIGABIT ROUTER WIRELESS 300N
GIGABIT ROUTER
WIRELESS 300N
300 MBPS WITH USB PORT
manual N I - 7 0 7 5 3 3
1
ENGLISH
2
C ontents o f the pac k age
5
T echnical S peci f ications
5
R ange o f applications
5
H ar d ware installation
6
R outer con f iguration
9
C onnecting to the internet
10
W P s
13
CE/FCC
14
W arrant y 17
3
ENGLISH
GIGABIT ROUTER
WIRELESS 300N
300 MBPS WITH USB PORT
Thank you for buying this 300N router. If you want to
interconnect several PC’s for shared Internet access,
you will need an additional component to connect
the PCs. This router allows you to set up a wireless
network, quickly and efficiently. The USB port
enables NAS functionality when connecting an
external hard disk.
C ontents o f the pac k age
Before starting the installation first check that all necessary
parts are present. The box should contain:
-
-
-
-
Gigabit Wireless Router 300N
Power adapter 12V 1.5A
CD with full manual
User manual
T echnical S peci f ications
-
802.11n wireless protocol
-
Maximum wireless data transfer speed: 300Mbps
-
Gigabit LAN, Gigabit WAN
-
Mimo (Multi In - Multi Out)
-
USB port for NAS functionality
-
Supports: IEEE 802.11b, and IEEE 802.11g
-
Supports: WEP/WPA/WPA2/TKIP/AES
-
3x Aerial 3dBi
-
Supports: 64/128/152 bit WEP encryption security
-
Maximum wired data transfer speed: 1Gbps
-
Web Based Management
-
Supports: Dynamic IP, Static IP, PPPoE
-
1 x WAN, 4 x LAN RJ-45 UTP ports
-
Built-in NAT and DHCP server
-
Supports: VPN pass through
-
Independent of operating system
R ange o f applications
This router allows you to set up a wireless broadband Internet
connection on multiple computers. On top of a shared Internet
4
5
connection, you can also set up a network between several PCs. Connect the ADSL or cables modem to the WAN port of the router and after
a few seconds the WAN LED will light up. You can now connect the PCs.
Once the PCs have been started up, the relevant LED will light up.
H ar d ware installation
As soon as you have connected the router to the power adapter, the power
LED (Green) will light up once. The other LEDs (Green) will light up as soon
as one of the UTP ports are connected to the computer. When data is
transferred from one computer to another the LEDs will start to flash.
LED Indicators
Name
Status
Indication
Power
Off
Power is off.
On
Power is on.
System
On
The Router is initializing or maybe has a system error.
Flashing
The Router is working properly.
Off
The Router has a system error.
WLAN, Off
The Wireless function is disabled.
Flashing
The Wireless function is enabled.
WAN
LAN
1-4
Off
There is no device linked to the corresponding port.
On
There is a device linked to the corresponding port but there is no activity.
There is an active device linked to the
Flashing
corresponding port.
USB
Off
There is no connected storage device
On
There is a device linked to the corresponding port
WPS
Slow Flash A wireless device is connecting to the network by WPS function. This process will last in the first 2 minutes.
A wireless device has been successfully added to On
6
the network by WPS function.
Quick Flash A wireless device failed to be added to the network by WPS function.
7
Overview of connections at the back of the router
R outer con f iguration
After you have correctly connected the router, you can start
to configure it. For some providers you will need addition
information, such as your username and a password.
Start up the Internet browser and enter the following address
in the address bar http://192.168.1.1 and press “Enter”
The following screen is displayed. To access the router enter
“admin” for username and “admin” for password and then
click “OK”
8
9
C onnecting to the internet
After successful login, you can configure the router using the
web browser. Please click the Quick Setup link on the left of
the main menu and the Quick Setup screen will appear. Click
Next to continue.
After you complete the above, click Next, the Wireless
settings screen will appear as the following:
The Choose WAN Connection Type screen will appear. Please
select one compatible with your ISP. Click Next to configure
the necessary network parameters.
If you have a Dynamic IP (or automatic IP) account, select
Dynamic IP and click Next, the router will automatically get IP
parameter from your ISP without entering any parameters.
If you have a fixed IP (or static IP) account, select Static IP
and click Next to load the following figure, and fill the blanks
with the parameters provided by your ISP.
10
At the end of the Quick Setup, click the Finish button to exit
this Quick Setup. The router should now be connecting you to
the Internet.
11
Use this space to write down your router’s settings.
Wireless Settings
SSID
: ……………………………..
PSK Passphrase: ……………………………..
NB
To get the most out of your router, please see the complete
manual on the CD-ROM.
W P S C on f iguration
WPS (Wi-Fi Protected Setup) function allows you to add a new
wireless device to an existing network quickly. WPS can only
be used if the router also supports this feature.
Push the button on the router and on the adapter and wait
until the following screen appears. Then click “Finish”.
The WPS connection can also be established by making the
connection in the software utility. This will also enable you to
use a PIN code. For more information on WPS, please read the
full manual on the CD.
12
13
C E M ar k W arning
This is a class B product. In a domestic environment, this
product may cause radio interference, in which case the user
may be required to take adequate measures.
National restrictions
This device is intended for home and office use in all EU
countries (and other countries following the EU directive 1999/5/
EC) without any limitation except for the countries mentioned
below:
Country Restriction
Reason/remark
Bulgaria
None
General authorization required for outdoor use and public service
France
Outdoor use limited to
10 mW e.i.r.p. within the
band 2454-2483.5 MHz
Military Radiolocation use.
Refarming of the 2.4 GHz band has
been ongoing in recent years to
allow current relaxed regulation.
Full implementation planned 2012
Italy
None
If used outside of own premises, general authorization is required
Luxembourg None
General authorization required for network and service supply(not for spectrum)
Norway
Implemented
This subsection does not apply for the geographical area within a
radius of 20 km from the centre of Ny-Ålesund
Russian Federation
Only for indoor applications
None
Please don’t use the product outdoors in France
14
F C C S TAT E M E N T
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
-
-
-
-
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions:
1)
2)
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.
15
Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
F C C R F R a d iation E x posure
S tatement:
This device has been tested for compliance with FCC RF
Exposure (SAR) limits in the typical laptop computer
configuration and this device can be used in desktop or
laptop computers. This device cannot be used with handheld
PDAs (personal digital assistants). This device and its
antenna must not be co-located or operated in conjunction
with any other antenna or transmitter. SAR measurements
are based on a 5mm spacing from the body and that
compliance is achieved at that distance.
WA R R A N T Y
Unless specified otherwise, all items sold under the ICIDU
name are covered by a 10-year warranty. No warranty or
support is provided for the software and rechargeable
batteries that are provided. Claims under warranty can
be made only via the dealer from whom the item was
purchased.
Specifications can be changed without notice.
All ICIDU products comply with current European safety and
environmental standards and legislation. For further details,
visit our website www.icidu.com
ICIDU is a registered trademark. All other brand names and rights in
connection with them are and remain the property of the rightful owner.
© Copyright 2011 ICIDU
All rights expressly reserved
16
17
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement