Log - Aten
eco PDU PE Series
PE7216 / PE7324 / PE8216 / PE8324
Power Distribution Unit
User Manual
www.aten.com
eco PDU PE Series User Manual
FCC, CE Information
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE
STATEMENT: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment.
CE Warning: This is a class A product. In a domestic environment this product
may cause radio interference in which case the user may be required to take
adequate measures.
NOTE: The KJ and J model series do not meet or qualify for FCC or CE
certification, as they are produced for countries outside the FCC’s jurisdiction.
RoHS
This product is RoHS compliant.
SJ/T 11364-2006
The following contains information that relates to China.
ii
eco PDU PE Series User Manual
User Information
Online Registration
Be sure to register your product at our online support center:
International
http://eservice.aten.com
Telephone Support
For telephone support, call this number:
International
886-2-8692-6959
China
86-10-5255-0110
Japan
81-3-5615-5811
Korea
82-2-467-6789
North America
1-888-999-ATEN ext 4988
United Kingdom
44-8-4481-58923
User Notice
All information, documentation, and specifications contained in this manual are subject
to change without prior notification by the manufacturer. The manufacturer makes no
representations or warranties, either expressed or implied, with respect to the contents
hereof and specifically disclaims any warranties as to merchantability or fitness for any
particular purpose. Any of the manufacturer's software described in this manual is sold
or licensed as is. Should the programs prove defective following their purchase, the
buyer (and not the manufacturer, its distributor, or its dealer), assumes the entire cost of
all necessary servicing, repair and any incidental or consequential damages resulting
from any defect in the software.
The manufacturer of this system is not responsible for any radio and/or TV interference
caused by unauthorized modifications to this device. It is the responsibility of the user
to correct such interference.
The manufacturer is not responsible for any damage incurred in the operation of this
system if the correct operational voltage setting was not selected prior to operation.
PLEASE VERIFY THAT THE VOLTAGE SETTING IS CORRECT BEFORE USE.
If any bodily injury or property damage with respect to operation of the product results
from users not having installed the product in accordance with the instructions provided
in the product’s user manual, or the product is used in an environment with a current
load over the designed specifications of the product, ATEN is not liable for any loss or
damage.
iii
eco PDU PE Series User Manual
PE Device Safety Notice
Š Set the maximum permissible breaker protection in the building circuitry to the
current rating specified on the rating plate. Observe all national regulations and
safety codes as well as deviations for breakers.
Only connect the PE Device to a grounded power outlet or a grounded system!
Š
Š Make sure that the total current input of the connected systems does not exceed
the current rating specified on the rating plate of the PE Device.
Š There is a risk of explosion if the battery is replaced with an incorrect type.
Dispose of used batteries according to the relevant instructions.
iv
eco PDU PE Series User Manual
Package Contents
The eco PDU PE Series package consists of:
1 PE7216 / PE7324 / PE8216 / PE8324 Power Distribution Unit
1 Power Cord (16-port models only)
1 Mounting Kit
1 CD-ROM
1 User Instructions*
Check to make sure that all of the components are present and in good order.
If anything is missing, or was damaged in shipping, contact your dealer.
Read this manual thoroughly and follow the installation and operation
procedures carefully to prevent any damage to the switch or to any other
devices on the eco PDU installation.
* Features may have been added to the eco PDU since this manual was
published. Please visit our website to download the most up-to-date version.
Copyright © 2015 ATEN® International Co., Ltd.
Manual Date: 2015-11-16
NRGence and the NRGence logo are registered trademarks of ATEN International Co., Ltd. All rights reserved.
All other brand names and trademarks are the registered property of their respective owners.
v
eco PDU PE Series User Manual
Contents
FCC, CE Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
SJ/T 11364-2006 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
PE Device Safety Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ix
Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x
Chapter 1.
Introduction
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Comparison Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Power Distribution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Remote Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
eco Sensors Energy Management Software* . . . . . . . . . . . . . . . . . . . . 5
Proactive Overload Protection (POP) . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Environment Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Door Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Cable Holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
PE7216 / PE8216 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
PE7324 / PE8324 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Port and LED Panel (All models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Chapter 2.
Hardware Setup
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
PDU Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Installation Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Securing the Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Securing the Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
vi
eco PDU PE Series User Manual
Chapter 3.
Basic Operation and
First Time Setup
Operation Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
eco Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
First Time Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Network Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Changing the Administrator Login . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Moving On. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Chapter 4.
Logging In
Logging In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
The eco PDU Main Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Page Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Chapter 5.
Energy
Energy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Chapter 6.
User Management
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Administrator Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Chapter 7.
Log
Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
The System Log Event List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Chapter 8.
Setup
Device Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Device Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Date/Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Login Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Working Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Account Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Login String / IP Filter / Mac Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Authentication & Authorization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
vii
eco PDU PE Series User Manual
Private Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Chapter 9.
PDU
PDU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Firmware File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Appendix
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
The eco PDU’s Main Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Securing the Power Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Resetting the Circuit Breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Recovery Procedure: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Technical Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
IP Address Determination. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
PE7216B / PE8216B. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
PE7216G / PE8216G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
PE7324B/J / PE8324B/J . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
PE7324G / PE8324G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Administrator Login Failure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
viii
eco PDU PE Series User Manual
Conventions
This manual uses the following conventions:
Monospaced
Indicates text that you should key in.
[]
Indicates keys you should press. For example, [Enter] means
to press the Enter key. If keys need to be chorded, they
appear together in the same bracket with a plus sign
between them: [Ctrl+Alt].
1.
Numbered lists represent procedures with sequential steps.
♦
Bullet lists provide information, but do not involve sequential
steps.
→
Indicates selecting the option (on a menu or dialog box, for
example), that comes next. For example, Start → Run
means to open the Start menu, and then select Run.
Indicates critical information.
ix
eco PDU PE Series User Manual
Product Information
For information about all NRGence products and how they can help you save
money in the data center, visit NRGence on the Web or contact an ATEN
Authorized Reseller. Visit ATEN on the Web for a list of locations and
telephone numbers
Š International – http://www.aten.com
Š North America – http://www.aten-usa.com
x
Chapter 1
Introduction
Overview
As part of its NRGence line, ATEN has developed a new generation of green
energy power distribution units (eco PDUs) to effectively increase the
efficiency of data center power usage. The NRGence PE7216 / PE7324 /
PE8216 / PE8324 eco PDUs are intelligent PDUs that contain 16 or 24 AC
outlets and are available in various IEC socket configurations. Models in the
advanced PE8 range feature NRGence’s proactive overload protection, which
automatically powers off the last outlet that caused the current overload.
NRGence eco PDUs provide secure, centralized, intelligent, power
management (power on, off, cycle) of data center IT equipment (servers,
storage systems, KVM switches, network devices, serial data devices, etc.), as
well as the ability to monitor the center's health environment via sensors*. The
basic characteristics of each model are shown in the table on page 3.
NRGence eco PDUs offer remote power control combined with real-time
power measurement – allowing you to control and monitor the power status of
devices attached to the PDUs, either at the PDU device, bank, or outlet level,
depending on the model, from practically any location via a TCP/IP
connection*.
The power status of each outlet can be set individually, allowing users to switch
each device On/Off. The eco PDU also offers comprehensive power analysis
reports which can separate departments and locations, providing precise
measurements of current, voltage, power and watt-hour in a real-time display.
Installation and operation is fast and easy: plugging cables into their
appropriate ports and user-friendly browser-based configuration and
management is all that is entailed. Since the eco PDU firmware is upgradeable
over the Net, you can stay current with the latest functionality improvements
simply by downloading updates from our website as they become available.
NRGence eco PDU supports any 3rd party V3 SNMP Manager Software and
NRGence eco Sensors (eco PDU Manager Software). eco Sensors provides
you with an easy method for managing multiple devices, offering an intuitive
and user-friendly Graphical User Interface that allows you to configure a PDU
device and monitor power status of the equipment connected to it.
1
eco PDU PE Series User Manual
With its advanced security features and ease of operation, the eco PDU is the
most convenient, most reliable, and most cost effective way to remotely
manage power access for multiple computer installations and allocate power
resources in the most efficient way possible.
Note: 1. Sensors are optional accessories. A sensor-enabled installation is
required to generate a more complete energy-efficient data and chart.
Higher sensor installation density is helpful to generate more accurate
data. See Optional Accessories, page 8, for further information.
2. eco PDUs are primarily designed for access via Intranet; extra
network security protection is suggested for Internet access usage.
3. Not all models support all features. See Comparison Chart, page 3,
and Specifications, page 68, for full details.
2
Chapter 1. Introduction
Comparison Chart
Model
PE7216B
Inlet / Cord
NEMA 6-20P
Outlets
16
PE8216B
PE7216G
14 x IEC 320 C13 +
2 x IEC 320 C19
Metering
Level
Outlet
Switching
PDU /
1 x Bank /
Outlet
No
IEC 60320 C20
No
PE8216G
PE7324B / J
Yes 16/16
NEMA L6-30P
PE8324B / J
PE7324G
PE8324G
Yes 16/16
IEC 60309 32A
24
21 x IEC 320 C13 +
3 x IEC 320 C19
PDU /
2 x Bank /
Outlet
No
Yes 24/24
No
Yes 24/24
Note: For the complete specifications of individual models, including bankby-bank outlet details, please reference Specifications, page 68.
3
eco PDU PE Series User Manual
Features
Power Distribution
Š Space saving 0U rack mount design with rear mounting
Š Various IEC outlet models
Š 2 digit 7-segment front panel LED shows PDU/Phase / Bank / Outlet ID
Š 3 digit 7-segment front panel LED shows Current / Voltage / Power
Dissipation, IP address, and readings from up to 4 environment sensors
Š Safe shutdown support
Š Separate power for the unit's own power and its power outlets – the user
interface is still accessible even when an overload condition trips the
devices' circuit breaker
Š Proactive overload protection (POP) (PE8 models only) – automatically
powers off the last outlet that caused the current overload (see Proactive
Overload Protection (POP), page 6)
Remote Access
Š Remote power control via TCP/IP and a built in 10/100 Ethernet port
Š Network Protocols: TCP/IP, UDP, HTTP, HTTPS, SSL, SMTP, DHCP,
NTP, DNS, auto sense, Ping
Š Remote users can monitor outlet status via web pages on their browsers
Š eco PDU Power Management software – eco Sensors
Š Supports SNMP Manager V3
Operation
Š Local and Remote power outlet control (On, Off, Power Cycle) by
individual outlets (PE8 models)
Š Supports multiple power control methods – Wake on LAN, System after
AC Back, Kill the Power
Š Power-on sequencing – set the power on sequence and delay time for each
outlet to allow equipment to be powered on in the correct order
Š Easy setup and operation via a browser-based user interface
Š Multibrowser support (IE, Mozilla, Firefox, Chrome, Safari, Opera)
Š RTC support to keep the timer running during times of no power
Š Up to 8 user accounts and 1 administrator account
4
Chapter 1. Introduction
Management
Š Power metering and monitoring at the PDU / Bank / Outlet level
Š LED indicators for current, voltage, power dissipation at the PDU / Bank /
Outlet levels
Š Real-time aggregate current, voltage, and power and power dissipation
displayed in a browser-based UI for monitoring at the PDU, bank and
outlet level (16-port models offer 1 bank metering; 24-port models offer 2
bank metering)
Š Alert notification for selected events (On, Off, Recycle, Failure, exceeding
threshold settings, etc.), via blinking LEDs (locally), SMTP, SNMP trap
notification
Š Supports Management Information Base (MIB) files for SNMP
Š Environment monitoring – supports external temperature / humidity /
differential pressure sensors for rack environment monitoring
Š Door Sensor support – allows the monitoring of rackmount enclosure door
access to notify users when a door has been opened.
Š Current and voltage threshold setting
Š Naming support for outlets
Š User outlet access assignment on an outlet-by-outlet basis
Š Event logging and syslog support
Š Upgradeable firmware
Š Multilanguage support – English, Traditional Chinese, Simplified
Chinese, Japanese, German, Italian, Spanish, French, Russian, Korean,
Portuguese
Security
Š Two-level password security
Š Strong security features include strong password protection and advanced
encryption technologies – 128 bit SSL
Š Remote authentication support: RADIUS
eco Sensors Energy Management Software*
Š Automatic discovery of all PE devices within the same intranet
Š Remote real-time power measurement and monitoring
Š Real-time environment sensor monitoring
5
eco PDU PE Series User Manual
Š Plotting/monitoring of all PE devices
Š Exceed threshold alert through SMTP and System log
Š Power Analysis report
Note: eco Sensors is designed to work with NRGence PDUs and is bundled
with all PE series packages.
Proactive Overload Protection (POP)
The PE8216 and PE8324 models feature NRGence’s exclusive Proactive
Overload Protection (POP) technology. Effective on all non-critical outlets,
this added safety feature automatically powers off the last outlet that caused the
current overload.
POP mode is engaged when the current exceeds the set threshold maximum
value, powering off the outlet. The LED display shows POP and a beeper
sounds. Press any button for two seconds to clear POP mode and power the
outlet back on.
6
Chapter 1. Introduction
Requirements
Š Browsers accessing the eco PDU unit must support SSL 128 bit
encryption.
Š For cold booting of attached computers, the computer's BIOS must
support Wake on LAN or System after AC Back.
Š For Safe Shutdown:
Š The computer must be running Windows (2000 or higher) or Linux.
Š The Safe Shutdown program (available by download from our website
or on the software CD included), must be installed and running on the
computer.
7
eco PDU PE Series User Manual
Optional Accessories
Environment Sensors
For complete energy management of an instrumented data center with the use
of the eco PDU and eco Sensors software, you should install 4 sensors for each
of the racks in your data center in order to generate a complete energy-efficient
data chart. Higher sensor installation density is helpful to generate more
accurate data. 8/16-port models have 4 sensor ports. Higher sensor installation
density is helpful to generate more accurate data.
To get the most complete eco Sensors Dashboard data, the recommended 4sensor setup is show in the table, below:
Port
Location
Part Number
Sensor
Intake
EA1140 or
Sensor 2
Intake
EA1240
Temperature or
Temperature / Humidity
Sensor 3
Exhaust
Sensor 4
Exhaust
EA1340
Differential Pressure
Sensor 1
or Floor
Door Sensor
All models in the PE7xxx/PE8xxx/PE9xxx range feature a 4-pin dry contact
port for door sensors that supports the monitoring of rackmount enclosure door
access to notify users when a door has been opened.
See the table below for information about the two available door sensors.
Please contact your ATEN dealer for purchasing information:
Port
Door Sensor
Part Number
Sensor
EA1440
Photo Sensor
EA1441
Inductive Proximity Sensor
Sensor Management
Sensors can be managed via the eco PDU’s built-in graphical user interface
(GUI) or with the NRGence eco Sensors software that can be downloaded from
the ATEN website. The download link can be found on the software CD
provided with the eco PDU package.
8
Chapter 1. Introduction
Cable Holders
Cable holders are optional accessories. For added safety, use ATEN Lok-UPlug cable holders to secure the cables from your attached devices in place on
the eco PDU unit. Use only the ATEN Lok-U-Plug cable holders that have
been specifically designed to work with the eco PDU. Using any other kind of
cable securing device could be highly dangerous.
Part Number
Description
2X-EA07
Lok-U-Plug Cable Holder (10 pcs)
2X-EA08
Lok-U-Plug Installation Tool (4 pcs)
9
eco PDU PE Series User Manual
Components
PE7216 / PE8216
PE8216
PE7216
1
5
2
1
5
3
4
Note: The PE7216 / PE8216 unit components are identical except for the
outlet LEDs – the PE7216 has none; and the PE8216 has 16, as shown
by number 5 above.
10
Chapter 1. Introduction
No.
Item
Description
1
Power Outlets*
16 in total (14 x IEC 320 C13 + 2 x IEC 320 C19)
Bank 1-1: Outlet 1–8: 7 C13; 1 x C19
Bank 1-2: Outlet 9–16: 7 x C13; 1 x C19
2
Port and LED Panel
The Port and LED panel contains:
Š Readout Section and LEDs
Š Environmental Sensor Ports
Š LAN Port
Š Door Sensor Port
Š Reset Switch
Full details of this section are provided on
page 14.
3
Circuit Breaker
Pushbutton
As a safety measure, if there is an overcurrent
situation regarding the device’s power, the circuit
breakers will trip. Press the button to recover
normal operation.
Warning: See Resetting the Circuit Breaker,
page 64 for important information about resetting a
tripped circuit breaker.
4
Power Inlet
The power cord that connects the unit to an AC
power source plugs into this socket.
Š B models connect to a NEMA 6-20P source
Š G models connect to an IEC 60320 C20 source
5
Outlet Status LEDs
PE8216 (x 16) only.
These LEDs indicate outlet status.
Lights ORANGE for powered on.
Off for powered off.
Note: Holes for ATEN Lok-U-Plug cable holders are located around the
outlets. See Securing the Cables, page 20, for further information.
11
eco PDU PE Series User Manual
PE7324 / PE8324
PE8324
PE7324
1
5
1
5
2
1
5
3
4
Note: The PE7324 / PE8324 unit components are identical except for the
outlet LEDs – the PE7324 has none; and the PE8324 has 24, as shown
by number 5 above.
12
Chapter 1. Introduction
No.
Item
Description
1
Power Outlets*
24 in total (21 x IEC 320 C13 + 3 x IEC 320 C19)
Bank 1-1: Outlet 1–8: 7 C13; 1 x C19
Bank 1-2: Outlet 9–16: 7 x C13; 1 x C19
Bank 2: Outlet 17–24: 7 x C13; 1 x C19
2
Port and LED Panel
The Port and LED panel contains:
Š Readout Section and LEDs
Š Sensor Ports
Š LAN Port
Š Door Sensor Port
Š Reset Switch
Full details of this section are provided on
page 14.
3
Circuit Breakers
As a safety measure, if there is an overcurrent
situation regarding the device’s power, the circuit
breakers will trip. Press the button to recover
normal operation.
Warning: See Resetting the Circuit Breaker,
page 79 for important information about resetting a
tripped circuit breaker.
4
Power Cord
Plug the cord into an AC power source.
Š B models connect to a NEMA L6-30P source
Š G models connect to an IEC 60309 32A source
5
Outlet Status LEDs
PE8324 (x 24) only.
These LEDs indicate outlet status.
Lights ORANGE for powered on.
Off for powered off.
13
eco PDU PE Series User Manual
Port and LED Panel (All models)
1
2
3
4
6
5
No.
1
Item
ID Section
7
Description
Š The ID of the selected PDU/Phase / Bank / Outlet appears in
the LED display window.
Š When PDU/Phase LED is lit, the LED display window will
show P1.
Š When BANK LED is lit, use the Up and Down buttons to move
Š
2
Readout
Section
Š When PDU/Phase / Bank / Outlet is selected, readouts for
Š
Š
3
Status LEDs
forward or backward through the following sequence: 01→02
(Bank1→Bank2)
When the Outlet LED is lit, use the Up and Down buttons to
move forward or backward through the outlets: 01→02→03→
... 01 (Outlet1→Outlet2→Outlet3→ ... Outlet1)
Current, Voltage, Power, and IP address appear in the display
window.
Press the button next to the LED display window to cycle the
selection between the items; the LEDs next to the items
indicate which one the display relates to.
When a sensor is selected, the display shows temperature /
humidity / differential pressure according to the sensor type
Š Power: Lights when the unit is powered up and ready to
operate.
Š Door sensor: Lights Red when the door is open. See Door
Sensor, page 8, for details.
14
Chapter 1. Introduction
No.
Item
Description
4
Sensor
Ports
External sensors plug into these four RJ-11 ports. See
Environment Sensors, page 8, and Securing the Sensors,
page 21, for further information.
5
Reset
Switch
This switch is recessed and must be pushed with a thin object,
such as the end of a paper clip.
Š Press and release to reboot the device.
Š Press and hold for more that three seconds to reset the eco
PDU to its factory default settings
6
LAN Port
The cable that connects the unit to the Internet, LAN, or WAN
plugs in here.
7
Door Sensor This 4-pin dry contact port is for a door sensor support – allows
the monitoring of rack mount enclosure door access to notify
users when a door has been opened. See Door Sensor, page 8,
for details.
15
Chapter 2
Hardware Setup
Before You Begin
1. Important safety information regarding the placement of this device is
provided on page 61. Please review it before proceeding.
2. Make sure that power to all the devices you will be connecting have
been turned off. You must unplug the power cords of any computers
that have the Keyboard Power On function.
3. See Resetting the Circuit Breaker, page 64 for important information
about resetting a tripped circuit breaker.
Rack Mounting
The eco PDU can be mounted in a 0U configuration on the side of a rack. To
rack mount the device, use the rack mounting brackets that came with your
device. The brackets can be mounted either near the top and bottom of the back
panel, or the top and bottom ends of the device, as shown in the diagram below:
16
Chapter 2. Hardware Setup
PDU Placement
For safety reasons the eco PDU should not be installed with the power sockets
facing directly up or down, and thus should only be installed with the power
sockets facing out from a vertical position as shown below:
Right.
Floor
Wrong
Floor
Note: The eco PDU models shown in the diagrams are for rack mount
reference purposes only.
17
eco PDU PE Series User Manual
Installation
To set up your installation, refer to the installation diagram on the next page
(the numbers in the diagram correspond to the numbered steps), and do the
following:
1. Ensure that the eco PDU unit is properly grounded.
Note: Do not omit this step. Proper grounding helps to prevent damage to
the unit from surges of static or electricity.
2. For each device you want to connect, use its power cable to connect from
the device's AC socket to any available outlet on the eco PDU. Use ATEN
Lok-U-Plug cable holders to secure them.
Note: See Securing the Cables, page 20, for details.
3. Plug the cable that connects the eco PDU to the LAN into the eco PDU's
LAN port.
4. (Optional) If you are using environmental sensors in your eco PDU
installation, connect up to four to the RJ-11 sensor ports on the unit’s front
panel.
Note: Sensors are optional. Please see Optional Accessories, page 8, and
the installation diagrams later in this chapter for further information.
5. (Optional) If you are using a door sensor in your eco PDU installation,
connect it to the 4-pin dry sensor port on the unit’s front panel.
Note: See Door Sensor, page 8, for further information.
6. Depending on your model, connect the eco PDU's built-in power cord to
an AC power source, or use the power cord provided to connect the eco
PDU’s power socket to an AC power source.
Once you have finished these installation steps, you can turn on the eco PDU
and the connected devices.
18
Chapter 2. Hardware Setup
Installation Diagram
2
4
3
5
2
6
19
eco PDU PE Series User Manual
Securing the Cables
For added safety, use ATEN Lok-U-Plug cable holders to secure the cables
from your attached devices in place on the eco PDU unit. Secure the cable
holders using the specially designed holes around the individual power outlets,
as shown below:
Note: 1. Cable holders are an optional accessory. See Cable Holders, page 9.
2. Use only the ATEN Lok-U-Plug cable holders that have been
specifically designed to work with the eco PDU. Using any other kind
of cable securing device could be highly dangerous.
20
Chapter 2. Hardware Setup
Securing the Sensors
Connect the sensors to the eco PDU’s front panel sensor ports and secure them
using sensor mounts, tie wraps, and adhesive cable tie holders. If you use a tie
wrap to secure the sensor, tighten the tie wrap over the recessed channel on the
sensor, as shown in the following diagram:
Note: 1. The sensors shown in the above diagram are for reference purposes
only. The sensors for the eco PDU may look slightly different.
2. Depending on the model and type of sensor, sensor mounts, tie wraps,
and adhesive cable tie holders may or may not be provided in the
package.
21
Chapter 3
Basic Operation and
First Time Setup
Operation Methods
NRGence eco PDU models provide three methods to access and manage your
installation: Browser, eco Sensors (eco PDU Management Software), and
SNMP.
Note: The following sections of this chapter contain information concerning
Browser operation. For eco Sensors operation, please reference the
separate eco Sensors User Manual. The eco Sensors software and User
Manual can be downloaded from the ATEN website.
Browser
NRGence eco PDUs can be accessed and controlled via any supported Internet
browser from any platform. See First Time Setup, page 23, and the following
sections in this chapter, for full details.
eco Sensors
All eco PDUs support eco Sensors (eco PDU Manager Software). NRGence
eco Sensors provides you with an easy method for managing multiple devices,
offering an intuitive and user-friendly Graphical User Interface that allows you
to configure a PDU device and monitor power status of the equipment
connected to it. NRGence eco Sensors can be downloaded from the ATEN
website, along with a separate eco Sensors User Manual.
SNMP
NRGence eco PDUs support any 3rd party V1, V2, V3 SNMP Manager
Software. SNMP Management Information Database (MIB) files for the eco
PDU device can be found on the software CD provided with the eco PDU
package, or can be downloaded from the ATEN website.
22
Chapter 3. Basic Operation and First Time Setup
First Time Setup
Once the eco PDU installation has been cabled up, the next task the
Administrator needs to perform involve configuring the network parameters,
changing the default Administrator login settings, and adding users.
The easiest way to accomplish this is to log in over the Net with a browser.
Note: 1. Since this is the first time you are logging in, use the default
Username: administrator; and the default Password: password. For
security purposes we recommend changing them to something unique
(see Changing the Administrator Login, page 25).
2. For remote methods of getting logged in to the network, see IP
Address Determination, page 66.
After you successfully log in, the eco PDU Energy/Connections page appears:
Note: Operation details are discussed in the next chapter. For further setup
information, continue with this chapter
23
eco PDU PE Series User Manual
Network Configuration
To set up the network, do the following:
1. Click the Setup tab.
2. This opens on the Device Configuration page. A screen similar to the one
below appears:
3. Fill in the fields according to the information provided under Device
Configuration, page 40.
24
Chapter 3. Basic Operation and First Time Setup
Changing the Administrator Login
To change the default Administrator username and password, do the following:
1. Click the User tab.
Once users have been added to the system, the Accounts page displays a
detailed list of users – with more information about them – in the large
central panel:
2. In the Administrator Information section at the top, reset the name and
password fields to something unique, then click Save (at the bottom of the
page.)
Note: If you forget the Administrator’s name or password, short the
mainboard jumper to restore the default Administrator account. See see
Administrator Login Failure, page 73 in the Appendix for full details.
Moving On
After setting up the network and changing the default Administrator username
and password, you can proceed to other administration activities – including
adding users. This is covered in the next chapter.
25
Chapter 4
Logging In
Logging In
The eco PDU can be accessed via a supported Internet browser from any
platform.
Note: Browsers must support SSL 128 bit encryption.
To access the eco PDU do the following:
1. Open your browser and specify the IP address of the eco PDU you want to
access in the browser's URL location bar.
Note: You can get the IP address from the eco PDU administrator, or see
IP Address Determination, page 66, for information about setting it
up yourself.
2. If a Security Alert dialog box appears, accept the certificate – it can be
trusted. The Login page appears:
3. Provide a valid Username and Password (set by the eco PDU
administrator).
4. Select your preferred Language from the drop-down menu.
5. Then Click Login to bring up the browser Main Page.
26
Chapter 4. Logging In
The eco PDU Main Page
After you have successfully logged in, the eco PDU Main Page comes up with
the Energy Connections page displayed:
Note: The screen depicts an Administrator’s page. Depending on a user’s type
and permissions, and your PE model, not all of these elements appear.
27
eco PDU PE Series User Manual
Page Components
The web page screen components are described in the table, below:
No.
Item
Description
1
Tab Bar
The tab bar contains the eco PDU’s main operation
categories. The items that appear in the tab bar are
determined by the user’s type, and the authorization
options that were selected when the user’s account
was created.
2
Menu Bar
The menu bar contains operational sub-categories
that pertain to the item selected in the tab bar. The
items that appear in the menu bar are determined by
the user’s type, and the authorization options that
were selected when the user’s account was created.
3
Sidebar
The Sidebar provides a tree view listing of outlets
that relate to the various tab bar and menu bar
selections.
4
Help
Connects to on-line help at the ATEN website for the
device’s configuration and operation.
5
Logout
Click this button to log out of your eco PDU session.
6
Interactive Display Panel This is your main work area. The screens that
appear reflect your menu choices and Sidebar node
selection.
The Energy page has two tabs: Connections and Configuration, as described in
the chapters that follow.
28
Chapter 5
Energy
Energy
Connections
When you log in to the eco PDU, the interface opens with its default selection
of the Energy tab; and the Connections menu. The contents of the PDU Status,
Bank Status, and Outlet Status sections are displayed in the main panel.
Note: Only enabled eco PDU models will display the Bank Status and/or
Outlet Status submenu section.
29
eco PDU PE Series User Manual
PDU Status
All eco PDU models support PDU device level monitoring. The PDU Status
section allows you to set up a power management configuration for the PDU
device as a whole:
„ PDU Threshold Settings
These fields are used to set the maximum, minimum, and fluctuation
threshold settings for Aggregate Current, Voltage, Power, and Aggregate
Power Dissipation. If a range falls below the minimum setting, or exceeds
the maximum setting an alarm is triggered.
Š Voltage Frequency is displayed here in Hz.
Š On / Off / Reboot
You can manually turn the device On and Off from this page by clicking
the radio buttons. To Reboot the device, enable the Reboot checkbox and
click on Save (located at the bottom of the page).
Š Door Sensor
This section allows you to select the type of door sensor that is being used
in the installation. See Door Sensor, page 8, for further information.
Š Sensor 1–4
If you have sensors installed in your installation, use these fields to set the
maximum, minimum, and fluctuation threshold settings for Temperature,
Humidity, and Pressure.
Note: Sensors are optional accessories. Check with your dealer for
information about NRGence eco Sensors software.
30
Chapter 5. Energy
Bank Status
All eco PDU models support Bank level monitoring. The Bank Status section
allows you to set up a power management configuration for the individual
banks:
„ Threshold Settings
These fields are used to set the maximum, minimum, and fluctuation
threshold settings for Aggregate Current, Voltage, Power, and Power
Dissipation. If a range falls below the minimum setting, or exceeds the
maximum setting an alarm is triggered.
Š Breaker status (ON / OFF) displays here.
31
eco PDU PE Series User Manual
Outlet Status
If your eco PDU models supports outlet level power management, threshold
settings and manual On/Off/Reboot switching can be performed on this page.
„ Threshold Settings
These fields are used to set the maximum, minimum, and fluctuation
threshold settings for Aggregate Current, Voltage, Power, and Power
Dissipation. If a range falls below the minimum setting, or exceeds the
maximum setting an alarm is triggered.
„ On / Off / Reboot
You can manually turn the outlet On and Off from this page by clicking the
radio buttons. To Reboot the outlet, enable the Reboot checkbox and click
on Save (located at the bottom of the page).
32
Chapter 5. Energy
Configuration
The Configuration page is used to configure the settings of the eco PDU at the
bank and individual power outlet level:
POP Setting
This section allows you to configure the settings for NRGence’s exclusive
Proactive Overload Protection (POP) technology. Effective on all non-critical
outlets, this added safety feature automatically powers off the last outlet that
caused the current overload.
Š Enable POP Mode by clicking the radio button
Š Make your selection for the POP Threshold – options are Same as Bank
Maximum Current or User Defined – Enter a value in the field.
Note: This feature is available on the PE8216 model only. See Proactive
Overload Protection (POP), page 6, for more details.
Bank Configuration
Each bank can be given a distinctive name. The maximum number of
characters is 15.
33
eco PDU PE Series User Manual
Outlet Configuration
This page lets you set up the power management configuration for the selected
outlet. The meanings of the field headings are given in the following table
:
Heading
Meaning
Outlet Name
Each outlet can be given a distinctive name. The maximum number of
characters is 15.
Confirmation
Required
If this option is enabled (there is a check in the checkbox), a dialog box
comes up asking you to confirm a power operation before it is
performed. If it is disabled (there is no check in the checkbox), the
operation is performed without confirmation.
Power ON
Delay
Sets the amount of time the eco PDU waits after the Power Button is
clicked (see Bank Status, page 31), before it powers on the outlet.
Note: The default delay time is 0 seconds; the maximum is 999 seconds. When a
series of outlets are scheduled to be powered up, they turn on in sequence with a
default delay of 10 milliseconds between each outlet.
Power OFF
Delay
Sets the amount of time the eco PDU waits after the Power Button is
clicked (see Bank Status, page 31), before it turns off the power to the
outlet.
For the System after AC Back option (see below), after the delay time
expires, the eco PDU waits another fifteen seconds, then shuts the
computer down.
The default delay time is 15 secs; the maximum delay time is 999 secs.
Remote Turn
ON Method
Use the drop-down menu to select one of the choices, below:
Wake on LAN: This is a Safe Shutdown and Restart option. If this is
selected, when an Outlet is turned Off, the eco PDU first sends a
message to the computer telling it to prepare for a shutdown; it then
waits for the amount time set in the Power Off Delay field to give the
OS time to close down before the computer is powered down to
standby mode.
Likewise, when the Outlet is turned On, the eco PDU waits for the
amount time set in the Power On Delay field, then sends an Ethernet
message to the computer connected to the Outlet telling the computer
to turn itself On.
Note: For Safe Shutdown and Restart, the computer must be running Windows
(98 or higher), or Linux, and the Safe Shutdown program (available by
download from our website), must be installed and running on the computer.
System after AC Back: This is a Safe Shutdown and Restart option. If
this is selected, when an Outlet is turned Off, the eco PDU first sends
a message to the computer telling it to prepare for a shutdown; it then
waits for the amount time set in the Power Off Delay field to give the
OS time to close down before the computer is powered down.
When the Outlet is turned On, the eco PDU waits for the amount time
set in the Power On Delay field, then sends power to the server.
When the server receives the power, it turns itself on.
Note: For Safe Shutdown and Reboot, the computer must be running Windows
(98 or higher), or Linux, and the Safe Shutdown program (available by
download from our website), must be installed and running on the computer.
(Continues on next page)
34
Chapter 5. Energy
Heading
Remote Turn
ON Method
Meaning
Kill the Power: If this option is selected, the eco PFDU waits for the
amount time set in the Power Off Delay field, and then turns the
Outlet's power Off. Turning the power off performs a cold (non-safe)
shutdown.
MAC Address In order to use either of the Safe Shutdown and Restart methods the
MAC address of the computer connected to the outlet must be filled in
here.
When you have finished making your configuration settings, click Save.
35
Chapter 6
User Management
Overview
When you select the User tab the screen comes up with the Accounts menu, and
the Administrator Information and User Information displayed in the main
panel:
Note: There is a pre-installed administrator account. It can be used to set up
the device and to begin creating users and groups. The Username for
this account is administrator; the password is password. For security
purposes, we strongly recommend changing these to something unique.
Administrator Information
This section is used to set the Administrator name and password. Only
Administrators can view this section. For details, see Changing the
Administrator Login, page 25.
36
Chapter 6. User Management
User Information
To add a user, do the following:
1. Select the user type in the Management drop-down menu.
2. Key in a name and password in the Name and Password fields.
3. Set the outlet-by-outlet permissions of the user in the Outlet field.
4. Set the Management field to Enable.
5. Click Save to save your settings.
Note: Values must be entered in both the Name and Password fields in
order to enable an account.
The various options are explained in more detail in the following table:
Field
Management
Description
The Management field allows you to Enable or Disable a
user’s account:
Š Enable – stores the user account
Š Disable – disables the user account
Name
From 1 to 16 characters are allowed.
Password
From 1 to 16 characters are allowed.
Outlet
This field allows you to set the outlet-by-outlet permissions of
the user. Click on the user/port icon to cycle through the three
permissions options, as follows:
User has complete access to this outlet.
User has read-only access to this outlet.
User has no access to this outlet.
Save
Click this button to save your operation or changes
37
Chapter 7
Log
Log
The eco PDU keeps a record of transactions that take place on its installation,
and stores up to 128 events at one time.
38
Chapter 7. Log
The System Log Event List
Š Clicking on a device in the Sidebar displays its log events in the main
panel’s log event list.
Š Clicking the Refresh button brings the log list up to date with the latest
events.
Š The entry box to the right of the Refresh button lets you set the number of
events to display per page. Simply key in the number of your choice.
Š The top right of the main panel shows the total number of pages in the log
file, and what page you are currently viewing.
Š The buttons on the bottom row function as follows:
Š Clear – click to erase the contents of the log event list
Š First Page – click to go to the first page of the log event list
Š Previous Page – click to move to the previous page of the log event
list
Š Next Page – click to move to the next page of the log event list
Š Last Page – click to move to the last page of the log event list
Š Export Log – click to save the contents of the log event list to file.
39
Chapter 8
Setup
Device Management
The Setup page allows administrators and users with device management
permission to configure and control overall eco PDU operations.
Device Configuration
This page presents information about the selected device, as described in the
following sections:
General
Item
Meaning
PDU Name
This field lets you give the device a unique name. Simply delete
whatever is in the text box and key in the name of your choice.
Click Save (located at the bottom of the page) to save the new
name.
MAC Address
This item displays the eco PDU’s MAC address.
Firmware Version
This item displays the current firmware version number. You can
reference it to see if there are newer versions available on the
ATEN website.
Rack Location
Name
This field lets you give the rack location a unique name for easy
reference.
40
Chapter 8. Setup
Service Ports
As a security measure, if a firewall is being used, the Administrator can specify
the port numbers that the firewall will allow. If a port other than the default is
used, users must specify the port number as part of the IP address when they
log in. If an invalid port number (or no port number) is specified, the eco PDU
will not be found.
Select whether to allow only secure browser logins, as show below:
An explanation of the fields is given in the table below:
Field
Explanation
HTTP
The port number for a browser login. The default is 80.
HTTPS
The port number for a secure browser login. The default is 443.
Note: 1. Valid entries for all of the Service Ports are from 1–65535.
2. The service ports cannot have the same value. You must set a
different value for each one.
3. If there is no firewall (on an Intranet, for example), it doesn’t matter
what these numbers are set to, since they have no effect.
41
eco PDU PE Series User Manual
IPv4 Configuration
The PDU’s IPv4 IP and DNS addresses (the traditional method of specifying
IP addresses) can either be assigned dynamically (DHCP), or a fixed IP address
can be specified.
Š For dynamic IP address assignment, select the Obtain IP address
automatically radio button. (This is the default setting.)
Š To specify a fixed IP address, select the Set IP address manually radio
button and fill in the IP address with values appropriate for your network.
Š For automatic DNS Server address assignment, select the Obtain DNS
Server address automatically radio button.
Š To specify the DNS Server address manually, select the Set DNS server
address manually radio button, and fill in the addresses for the Preferred
and Alternate DNS servers with values appropriate for your network.
Note: 1. If you choose Obtain IP address automatically, when the device starts
up it waits to get its IP address from the DHCP server. If it hasn’t
obtained the address after one minute, it automatically reverts to its
factory default IP address (192.168.0.60.)
2. If the device is on a network that uses DHCP to assign network
addresses, and you need to ascertain its IP address, see IP Address
Determination, page 66, for information.
3. Specifying the Alternate DNS Server address is optional.
42
Chapter 8. Setup
IPv6 Configuration
IPv6 is the new (128-bit) format for specifying IP addresses. The PDU’s IPv6
IP and DNS addresses can either be assigned dynamically (DHCP), or a fixed
IP address can be specified.
Š For dynamic IP address assignment, select the Obtain IP address
automatically radio button. (This is the default setting.)
Š To specify a fixed IP address, select the Set IP address manually radio
button and fill in the IP address with values appropriate for your network.
Š For automatic DNS Server address assignment, select the Obtain DNS
Server address automatically radio button.
Š To specify the DNS Server address manually, select the Set DNS server
address manually radio button, and fill in the addresses for the Preferred
and Alternate DNS servers with values appropriate for your network.
Note: 1. If you choose Obtain IP address automatically, when the device starts
up it waits to get its IP address from the DHCP server. If it hasn’t
obtained the address after one minute, it automatically reverts to its
factory default IP address (192.168.0.60.)
2. If the device is on a network that uses DHCP to assign network
addresses, and you need to ascertain its IP address, see IP Address
Determination, page 66, for information.
3. Specifying the Alternate DNS Server address is optional.
43
eco PDU PE Series User Manual
Event Notification
The Event Notification section is divided into three sections: SMTP Settings;
SNMP Trap Receivers; and Syslog Server. Each section is described below.
Note: SMTP communications are supported on Port 25.
„ SMTP Settings
To have the eco PDU device email reports from the SMTP server to you, do
the following:
1. Enable the Enable report from the following SMTP server, and key in the
IP address of your SMTP server.
2. If your server requires authentication, put a check in the My server
requires authentication checkbox.
3. Key in the appropriate account information in the Account Name,
Password, and From fields.
Note: Only one email address is allowed in the From fields, and it cannot
exceed 64 characters.)
4. Key in the email address (addresses) of where you want the event reports
sent to in the To field.
Note: If you are sending the report to more than one email address,
separate the addresses with a semicolon or comma, depending on
the specified mail server. The total cannot exceed 256 characters.
44
Chapter 8. Setup
„ SNMP Trap Receivers
Up to four SNMP management stations can be specified. If you want to use
SNMP trap notifications, do the following:
1. Check Enable SNMP Trap.
2. Select which version of SNMP you want to use.
3. Key in the IP address(es) and the service port number(s) of the
computer(s) to be notified of SNMP trap events. The valid port range is
1–65535. The default port number is 162.
Note: Make sure that the port number you specify here matches the port
number used by the SNMP receiver computer.
4. Key in the community value(s) if required for the SNMP version.
5. Key in the auth/privacy password(s) that correspond to each of the
stations.
45
eco PDU PE Series User Manual
„ Syslog Server
To record all the events that take place on eco PDU devices and write them to
the eco PDU Syslog server, do the following:
1. Check Enable Syslog Server.
2. Key in the IP address and the port number of the Syslog server. The valid
port range is 1-65535. The default port number is 514.
46
Chapter 8. Setup
Date/Time
The Date/Time dialog page sets the eco PDU time parameters:
Set the parameters according to the information described below.
Time Zone
Š To establish the time zone that the eco PDU is located in, drop down the
Time Zone list and choose the city that most closely corresponds to where
it is at.
Š If your country or region employs Daylight Saving Time (Summer Time),
check the corresponding checkbox.
47
eco PDU PE Series User Manual
Manual Input
Use this section to specify the eco PDU’s date and time manually.
Š Click the calendar icon and click the calendar entry for the date.
Š Key the time into the Time field, using the HH:MM:SS (hours, minutes,
seconds) format.
Note: This section is only enabled when auto adjustment (in the Network Time
section) is disabled (the checkbox is unchecked).
As an alternative to specifying the date and time by entering them into the date
and time fields, you can click to put a check in the Sync with PC checkbox, in
which case the eco PDU will take its date and time settings from the locally
connected PC.
Network Time
To have the time automatically synchronized to a network time server, do the
following:
1. Check the Enable auto adjustment checkbox.
2. Drop down the time server list to select your preferred time server
– or –
Check the Preferred custom server IP checkbox, and key in the IP address
of the time server of your choice.
3. If you want to configure an alternate time server, check the Alternate time
server checkbox, and repeat step 2 for the alternate time server entries.
4. Key in your choice for the number of days between synchronization
procedures.
Finishing Up
When you have finished making your settings on this page, click Save.
After you have saved your changes, if you want to synchronize immediately,
click Adjust Time Now.
48
Chapter 8. Setup
Security
The Security page controls access to the eco PDU.
Login Failures
Š Allowed sets the number of consecutive failed login attempts that are
permitted from a remote user.
Š Timeout sets the amount of time a remote user must wait before
attempting to login again after exceeding the number of allowed failures.
Working Mode
Š If ICMP is enabled, the eco PDU device can be pinged. If it is not
enabled, the device cannot be pinged. The default is Enabled.
49
eco PDU PE Series User Manual
Account Policy
The Account Policy section governs policies in regard to usernames and
passwords.
Check a policy and enter the required information in the appropriate fields.=
Item
Description
Minimum Username Length
Sets the minimum number of characters required for
a username. Acceptable values are from 1–16.
Minimum Password Length
Sets the minimum number of characters required for
a password. Acceptable values are from 1–16.
Password Must Contain At Least Checking any of these items requires users to include
at least one of the specified items in their password.
Note: This policy does not affect existing user
accounts. Only new user accounts created after this
policy has been enabled, and users required to
change their passwords are affected.
Disable Duplicate Login
50
Check this to prevent users from logging in with the
same account at the same time.
Chapter 8. Setup
Login String / IP Filter / Mac Filter
„ Login String
The Login String entry field is used to specify a login string (in addition to the
IP address) that users must include when accessing the eco PDU device with a
browser. For example:
192.168.0.126/abcdefg
Š The following characters are allowed:
0–9 a–z A–Z ~ ! @ $ * ( ) _ ‘ ,
Š The following characters are not allowed:
& ^ { } ‘ ’ < > | " % ” : / ? # \ [Space] + - = [ ] ;
Compound characters (É Ç ñ ... etc.)
Note: 1. There must be a forward slash between the IP address and the string.
2. If no login string is specified here, anyone will be able to access the
eco PDU device login page using the IP address alone. This makes
your installation less secure.
For security purposes, we recommend that you change this string occasionally.
51
eco PDU PE Series User Manual
„ IP Filter / MAC Filter
If any filters have been configured, they appear in the IP Filter and/or MAC
Filter list boxes.
IP and MAC Filters control access to the eco PDU based on the IP and/or MAC
addresses of the client computers attempting to connect. A maximum of 5 IP
filters and 5 MAC filters are allowed.
To enable IP and/or MAC filtering, click to put a check mark in the IP Filter
Enable and/or MAC Filter Enable checkbox.
Š If the include button is checked, all the addresses within the filter range are
allowed access; all other addresses are denied access.
Š If the exclude button is checked, all the addresses within the filter range
are denied access; all other addresses are allowed access.
Adding Filters
To add an IP filter, do the following:
1. Click Add. A dialog box similar to the one below appears:
2. Specify the filter address in the dialog box (for example, 192.168.0.200),
then click OK.
A second dialog box, similar to the one below, appears:
52
Chapter 8. Setup
3. To filter a single IP address, key in the same address as the start IP. To
filter a continuous range of addresses, key in the end number of the range
(for example, 192.168.0.225).
4. After filling in the address, click OK.
Repeat these steps for any additional IP addresses you want to filter.
To add a MAC filter, do the following:
1. Click Add. A dialog box similar to the one below appears:
2. Specify the MAC address in the dialog box (for example, 001074670000),
then click OK.
Repeat these steps for any additional MAC addresses you want to filter.
IP Filter / MAC Filter Conflict
If there is a conflict between an IP filter and a MAC filter – for example, where
a computer’s IP address is allowed by the IP filter but its MAC address is
excluded by the MAC filter – then that computer’s access is blocked.
In other words, if either filter blocks a computer, then the computer is blocked,
no matter what the other filter is set to.
Modifying Filters
To modify a filter, select it in the IP Filter or MAC Filter list box and click
Modify. The Modify dialog box is similar to the Add dialog box. When it
comes up, simply delete the old address(es) and replace it with the new one(s).
Deleting Filters
To delete a filter, select it in the IP Filter or MAC Filter list box and click
Delete.
53
eco PDU PE Series User Manual
Authentication & Authorization
The Authentication & Authorization page is used to set up login authentication
and authorization management from external sources.
54
Chapter 8. Setup
RADIUS Settings
To allow authentication and authorization for the eco PDU device through a
RADIUS server, do the following:
1. Check Enable.
2. Fill in the IP addresses and service port numbers for the Preferred and
Alternate RADIUS servers. The default port number for the Preferred
server is 1812; the default port number for the Alternate server is 1645.
Note: Make sure that the port numbers you specify here match the port
numbers used by the RADIUS servers.
3. In the Timeout field, set the time in seconds that the eco PDU device waits
for a RADIUS server reply before it times out.
4. In the Retries field, set the number of allowed retries for attempting to
connect to the RADIUS server.
5. In the Shared Secret field, key in the character string that you want to use
for authentication between the eco PDU device and the RADIUS Server.
6. On the RADIUS server, set the entry for each user as follows:
su/xxxx
Where xxxx represents the Username given to the user when the account
was created on the eco PDU device. The user’s access rights are the ones
assigned for the eco PDU device, as well. (See Device Management,
page 40.)
Note: su/user supports view ports only; su/administrator supports all eco PDU
functions.
55
eco PDU PE Series User Manual
Private Certificate
When logging in over a secure (SSL) connection, a signed certificate is used to
verify that the user is logging in to the intended site. For enhanced security, the
Private Certificate section allows you to use your own private encryption key
and signed certificate, rather than the default ATEN certificate.
There are two methods for establishing your private certificate: generating a
self-signed certificate; and importing a third-party certificate authority (CA)
signed certificate.
Generating a Self-Signed Certificate
If you wish to create your own self-signed certificate, a free utility –
openssl.exe – is available for download over the web.
Obtaining a CA Signed SSL Server Certificate
For the greatest security, we recommend using a third party certificate
authority (CA) signed certificate. To obtain a third party signed certificate, go
to a CA (Certificate Authority) website to apply for an SSL certificate. After
the CA sends you the certificate and private encryption key, save them to a
convenient location on your computer.
Importing the Private Certificate
To import the private certificate, do the following:
1. Click Browse to the right of Private Key; browse to where your private
encryption key file is located; and select it.
2. Click Browse to the right of Certificate; browse to where your certificate
file is located; and select it.
3. Click Upload to complete the procedure.
Note: 1. Clicking Restore Default returns the device to using the default
ATEN certificate.
2. Both the private encryption key and the signed certificate must be
imported at the same time.
When you have finished making your settings on this page, click Save.
56
Chapter 9
PDU
PDU
The PDU function is used to upgrade the eco PDU’s firmware, and to backup
and restore the device’s configuration settings.
Firmware File
When you click the PDU tab, the display opens with the Upgrade Main
Firmware menu page, which looks similar to the one below:
57
eco PDU PE Series User Manual
A description of the items shown in this panel are given in the table, below:
Item
Description
Check Main
Firmware Version
If you enable Check Main Firmware Version, the eco PDU’s
current firmware level is compared with that of the upgrade file. If
the current version is equal to or higher than the upgrade version,
a popup message appears, to inform you of the situation and stops
the upgrade procedure.
Name
Lists all of the eco PDU devices. Click to put a check in the
checkbox of the device’s whose firmware you want to upgrade.
F/W Version
Displays the eco PDU’s current firmware version.
Filename
As new versions of the firmware become available, they are
posted on our website and can be downloaded to a convenient
location on your computer. Click the Browse button to select the
downloaded upgrade file.
Upgrade
Click this button to upgrade the firmware of the selected devices.
58
Chapter 9. PDU
Upgrading the Firmware
To upgrade the firmware refer to the screenshot on the preceding page, and do
the following:
1. Go to our website and download the new firmware file to a convenient
location on your computer.
2. Click the Browse button; navigate to where the firmware file is located and
select it.
3. Click Upgrade to start the upgrade procedure.
Š If you enabled Check Main Firmware Version the current firmware
level is compared with that of the upgrade file. If the current version is
equal to or higher than the upgrade version, a popup message appears,
to inform you of the situation and stops the upgrade procedure.
Š If you didn't enable Check Main Firmware Version, the upgrade file is
installed without checking what its level is.
Š Once the upgrade completes successfully, the switch resets itself.
4. Log in again, and check the firmware version to be sure it is the new one.
„ Firmware Upgrade Recovery
Should the eco PDU’s firmware upgrade procedure fail, and the device
becomes unusable, the following firmware upgrade recovery procedure will
resolve the problem:
1. Power off the device.
2. Press and hold the Reset Switch in (see page 10).
3. While holding the Reset Switch in, power the switch back on.
This causes the switch to use the original factory installed main firmware
version. Once the switch is operational, you can try upgrading the main
firmware again.
59
eco PDU PE Series User Manual
Backup
To backup the device’s settings do the following:
1. In the Password field, key in a password for the file.
Note: Entering a password is optional. If you do enter a password, make a
note of it, since you will need it to be able to restore the file.
2. Click Save.
3. When the browser asks what you want to do with the file, select Save to
disk; then save it in a convenient location.
Restore
To restore a previous backup, do the following:
1. Click Browse; navigate to the file and select it.
Note: If you renamed the file, you can leave the new name. There is no
need to return it to its original name.
2. In the Password field, key in the same password that you used to save the
file.
Note: If you did not set a password when you created the backup file, you
can omit this step.
3. Select as many of the options that are presented as you wish to restore.
4. Click Restore.
After the file is restored, a message appears to inform you that the
procedure succeeded.
60
Appendix
Safety Instructions
General
Š This product is for indoor use only.
Š Read all of these instructions. Save them for future reference.
Š Follow all warnings and instructions marked on the device.
Š Do not place the device on any unstable surface (cart, stand, table, etc.). If
the device falls, serious damage will result.
Š Do not use the device near water.
Š Do not place the device near, or over, radiators or heat registers.
Š The device cabinet is provided with slots and openings to allow for
adequate ventilation. To ensure reliable operation, and to protect against
overheating, these openings must never be blocked or covered.
Š The device should never be placed on a soft surface (bed, sofa, rug, etc.) as
this will block its ventilation openings. Likewise, the device should not be
placed in a built in enclosure unless adequate ventilation has been
provided.
Š Never spill liquid of any kind on the device.
Š Unplug the device from the wall outlet before cleaning. Do not use liquid
or aerosol cleaners. Use a damp cloth for cleaning.
Š The device should be operated from the type of power source indicated on
the marking label. If you are not sure of the type of power available,
consult your dealer or local power company.
Š To prevent damage to your installation it is important that all devices are
properly grounded.
Š The device is equipped with a 3-wire grounding type plug. This is a safety
feature. If you are unable to insert the plug into the outlet, contact your
electrician to replace your obsolete outlet. Do not attempt to defeat the
purpose of the grounding-type plug. Always follow your local/national
wiring codes.
Š The equipment should be installed near the wall socket outlet and the
disconnect device (appliance coupler on detachable power supply cord or
plug on non-detachable power supply cord) should be readily accessible.
61
eco PDU PE Series User Manual
Š Do not allow anything to rest on the power cord or cables. Route the
power cord and cables so that they cannot be stepped on or tripped over.
Š To help protect your system from sudden, transient increases and
decreases in electrical power, use a surge suppressor, line conditioner, or
uninterruptible power supply (UPS).
Š Position system cables and power cables carefully; Be sure that nothing
rests on any cables.
Š When connecting or disconnecting power to hot pluggable power supplies,
observe the following guidelines:
Š Install the power supply before connecting the power cable to the
power supply.
Š Unplug the power cable before removing the power supply.
Š If the system has multiple sources of power, disconnect power from the
system by unplugging all power cables from the power supplies.
Š Never push objects of any kind into or through cabinet slots. They may
touch dangerous voltage points or short out parts resulting in a risk of fire
or electrical shock.
Š Do not attempt to service the device yourself. Refer all servicing to
qualified service personnel.
Š If the following conditions occur, unplug the device from the wall outlet
and bring it to qualified service personnel for repair.
Š The power cord or plug has become damaged or frayed.
Š Liquid has been spilled into the device.
Š The device has been exposed to rain or water.
Š The device has been dropped, or the cabinet has been damaged.
Š The device exhibits a distinct change in performance, indicating a need
for service.
Š The device does not operate normally when the operating instructions
are followed.
Š Only adjust those controls that are covered in the operating instructions.
Improper adjustment of other controls may result in damage that will
require extensive work by a qualified technician to repair.
Š Do not connect the RJ-11 connector marked “Sensor” to a public
telecommunication network.
62
Appendix
Rack Mounting
Š Before working on the rack, make sure that the stabilizers are secured to
the rack, extended to the floor, and that the full weight of the rack rests on
the floor. Install front and side stabilizers on a single rack or front
stabilizers for joined multiple racks before working on the rack.
Š Always load the rack from the bottom up, and load the heaviest item in the
rack first.
Š Make sure that the rack is level and stable before extending a device from
the rack.
Š Use caution when pressing the device rail release latches and sliding a
device into or out of a rack; the slide rails can pinch your fingers.
Š After a device is inserted into the rack, carefully extend the rail into a
locking position, and then slide the device into the rack.
Š Do not overload the AC supply branch circuit that provides power to the
rack. The total rack load should not exceed 80 percent of the branch circuit
rating.
Š Make sure that all equipment used on the rack – including power strips and
other electrical connectors – is properly grounded.
Š Ensure that proper airflow is provided to devices in the rack.
Š Ensure that the operating ambient temperature of the rack environment
does not exceed the maximum ambient temperature specified for the
equipment by the manufacturer
Š Do not step on or stand on any device when servicing other devices in a
rack.
The eco PDU’s Main Power Cord
Use the power cord supplied with this package. If it becomes necessary to
replace the cord supplied with this package, be sure to use a cord of at least the
same standard as the one provided.
Securing the Power Cables
To secure the cables in the eco PDU’s power outlets, use only the
ATEN Lock-Your-Plug cable holders that have been specifically
designed to work with the eco PDU. Using any other kind of cable securing
device could be highly dangerous. Please contact your ATEN dealer for
information about ATEN Lock-Your-Plugs.
63
eco PDU PE Series User Manual
Resetting the Circuit Breaker
Before switching the circuit breaker to reset a trip, power down and disconnect
all devices connected to the eco PDU's power outlets to prevent damage caused
by a sudden power surge. If a power surge causes the eco PDU’s circuit breaker
to switch off the power and it needs to be reset, follow the instructions below.
Recovery Procedure:
1. Safely power down and disconnect all devices connected to the eco PDU's
power outlets.
2. Switch off the circuit breaker for the source that is providing power to the
eco PDU.
3. Switch the eco PDU's circuit breaker to reset the trip.
4. Switch on the circuit breaker for the source that is providing power to the
eco PDU.
5. Reconnect the devices to the eco PDU’s power outlets, and power them
on.
64
Appendix
Technical Support
International
Š For online technical support – including troubleshooting, documentation,
and software updates: http://eservice.aten.com
Š For telephone support, see Telephone Support, page iii
North America
Email Support
Online
Technical
Support
[email protected]
Troubleshooting
Documentation
Software Updates
Telephone Support
http://www.aten-usa.com/support
1-888-999-ATEN ext 4988
When you contact us, please have the following information ready beforehand:
Š Product model number, serial number, and date of purchase.
Š Your computer configuration, including operating system, revision level,
expansion cards, and software.
Š Any error messages displayed at the time the error occurred.
Š The sequence of operations that led up to the error.
Š Any other information you feel may be of help.
65
eco PDU PE Series User Manual
IP Address Determination
If you are an administrator logging in for the first time, you need to access the
eco PDU in order to give it an IP address that users can connect to. There are
two methods to choose from. In each case, your client computer must be on the
same network segment as the eco PDU. After you have connected and logged
in you can give the device its fixed network address. (See Device Management,
page 49.)
Method 1:
For computers running Windows, an IP address can be determined and/or
assigned with the IP Installer utility. The utility can be obtained from the
Download area of our web site or from the software CD. Look under Driver/
SW, and the model of your device. After downloading the utility to your
computer, do the following:
1. Unzip the contents of IPInstaller.zip to a directory on your hard drive.
2. Go to the directory that you unzipped the IPInstaller program to and run
IPInstaller.exe. A dialog box similar to the one below appears:
(Continues on next page.)
66
Appendix
(Continued from previous page.)
3. Select the device in the Device List.
Note: 1. If the list is empty, or your device doesn't appear, click
Enumerate to refresh the Device List.
2. If there is more than one device in the list, use the MAC address
to pick the one you want. The eco PDU's MAC address is located
on its bottom panel.
4. Select either Obtain an IP address automatically (DHCP), or Specify an
IP address. If you chose the latter, fill the IP Address, Subnet Mask, and
Gateway fields with the information appropriate to your network.
5. Click Set IP.
6. After the IP address shows up in the Device List, click Exit to end the
program.
Method 2:
1. Set your computer's IP address to 192.168.0.XXX
Where XXX represents any number or numbers except 60. (192.168.0.60) is
the default address of the eco PDU.)
2. Specify the device’s default IP address (192.168.0.60) in your browser,
and you will be able to connect.
3. Assign a fixed IP address for the device (see IPv4 Configuration, page 51),
that is suitable for the network segment that it resides on.
4. After you log out, reset your computer's IP address to its original value.
5. Once you have logged in, go to Network Settings to set up the permanent
IP environment (see IPv4 Configuration, page 51).
Method 3:
NRGence eco Sensors allows you to determine/assign an IP address in order to
configure a PDU device and monitor power status of the equipment connected
to it. NRGence eco Sensors can be obtained from the Download area of the
ATEN web site.
67
eco PDU PE Series User Manual
Specifications
There are 8 models in the PE7xxx / PE8xxx range. They are available in 16-,
and 24-port versions, with power inlet/cord variations. A basic comparison is
show in the table, below.
Basic Comparison
Model
PE7216B
Inlet / Cord
NEMA 6-20P
Outlets
16
PE8216B
PE7216G
14 x IEC 320 C13 +
2 x IEC 320 C19
Metering Level
PDU /
1 x Bank /
Outlet
IEC 60320 C20
PE8324G
Yes 16/16
Yes 16/16
NEMA L6-30P
PE8324B / J
PE7324G
No
No
PE8216G
PE7324B / J
Outlet
Switching
IEC 60309 32A
24
21 x IEC 320 C13 +
3 x IEC 320 C19
PDU /
2 x Bank /
Outlet
No
Yes 24/24
No
Yes 24/24
Note: The J models are identical to their B model counterparts but have power
cords designed for the Japanese market.
68
Appendix
PE7216B / PE8216B
Function
Power Outlets
Direct
Connectors
Power Inlet
Power
Outlets
PE7216B
1 x NEMA 6-20P
NEMA
IEC
Environment Sensors
Door Sensor
Outlet Status
NA
PDU / Bank / Outlet
2-digit 7-segment (Orange)
Current / Volt / P.D. / Sensor1–
Sensor4 /
FW Upgrade
Current / Volt / P.D. / IP /
Sensor1–Sensor4
Door Open
7 (Green)
1 (Blue)
LED Display Select
PDU / Bank / Outlet Select
Reset
1 x Pushbutton
2 x Pushbutton
1 x Semi-recessed Pushbutton
Power
1 x 16A Branch Breaker
Nominal Input Power
100–240V~; 50–60Hz; 16A (UL), 20A (Max.)
Power Capacity
4.16kW
Per Port
IEC 320 C19
100–240V~; 50–60Hz; 16A (UL), 20A (Max.)
IEC 320 C13
100–240V~; 50–60Hz; 12A (UL), 15A (Max.)
Total
Operating Temperature
Storage Temperature
Humidity
Physical
Properties
3 (Green)
3-digit 7-segment (Orange)
1 (Green)
Power
Environment
16 (Orange)
1 (Red)
IP
Nominal Output
Power
4 x RJ-11 Female (Black)
1 x RJ-45 Female (Silver) + LEDs (Orange/
Green)
PDU / Bank / Outlet
Switches
NA
Total: 14 x IEC 320 C13 + 2 x IEC 320 C19
Bank 1-1, Outlet 1–8: 7 x C13 + 1 x C19.
Bank 1-2, Outlet 9–16: 7 x C13 + 1 x C19
1 x 4-pin Dry Contact
LAN
LEDs
PE8216B
16
100–240V~; 50–60Hz; 16A (UL), 20A (Max.)
0–50oC
-20–60oC
0–80% RH Non-condensing
Housing
Metal
Weight
3.80 kg
Dimensions (L x W x H)
132.48 x 6.60 x 4.40 cm
69
eco PDU PE Series User Manual
PE7216G / PE8216G
Function
Power Outlets
Direct
Connectors
Power Inlet
Power
Outlets
PE7216G
1 x IEC 320 C20
NEMA
IEC
Environment Sensors
Door Sensor
Outlet Status
NA
PDU / Bank / Outlet
2-digit 7-segment (Orange)
Current / Volt / P.D. / Sensor1–
Sensor4 /
FW Upgrade
Current / Volt / P.D. / IP /
Sensor1–Sensor4
Door Open
Reset
1 x Pushbutton
2 x Pushbutton
1 x Semi-recessed Pushbutton
Power
1 x Non-fuse Breaker
Nominal Input Power
100–240V~; 50–60Hz; 16A
Power Capacity
4.60kW
Per Port
IEC 320 C19
IEC 320 C13
Total
Operating Temperature
Storage Temperature
Humidity
100–240V~; 50–60Hz; 15A (TUV), 16A (Max.)
100–240V~; 50–60Hz; 10A
100–240V~; 50–60Hz; 15A (TUV), 16A (Max.)
0–40oC
-20–60oC
0–80% RH Non-condensing
Housing
Metal
Weight
3.8 kg
Dimensions (L x W x H)
70
7 (Green)
1 (Blue)
LED Display Select
PDU / Bank / Outlet Select
Physical
Properties
3 (Green)
3-digit 7-segment (Orange)
1 (Green)
Power
Environment
16 (Orange)
1 (Red)
IP
Nominal Output
Power
4 x RJ-11 Female (Black)
1 x RJ-45 Female (Silver) + LEDs (Orange/
Green)
PDU / Bank / Outlet
Switches
NA
Total: 14 x IEC 320 C13 + 2 x IEC 320 C19
Bank 1-1, Outlet 1–8: 7 x C13 + 1 x C19.
Bank 1-2, Outlet 9–16: 7 x C13 + 1 x C19
1 x 4-pin Dry Contact
LAN
LEDs
PE8216G
16
132.48 x 6.60 x 4.40 cm
Appendix
PE7324B/J / PE8324B/J
Function
Power Outlets
Direct
Connectors
Power Cord
Power
Outlets
PE7324B / J
1 x NEMA L6-30P
IEC
Environment Sensors
Door Sensor
Outlet Status
NA
PDU / Bank / Outlet
2-digit 7-segment (Orange)
Current / Volt / P.D. /Sensor1–
Sensor4 /
FW Upgrade
Current / Volt / P.D. / IP /
Sensor1–Sensor4
Door Open
7 (Green)
1 (Blue)
LED Display Select
PDU / Bank / Outlet Select
Reset
1 x Pushbutton
2 x Pushbutton
1 x Semi-recessed Pushbutton
Power
2 x Branch Breaker
Nominal Input Power
100–240V~; 50–60Hz; 24A (UL), 30A (Max.)
Nominal Input/Output Voltage
200–240 VAC
Power Capacity
6.24kW
Per Port
IEC 320 C19
100–240V~; 50–60Hz; 12A (UL), 15A (Max.)
IEC 320 C13
100–240V~; 50–60Hz; 12A (UL), 15A (Max.)
Total
Operating Temperature
Storage Temperature
Humidity
Physical
Properties
3 (Green)
3-digit 7-segment (Orange)
1 (Green)
Power
Environment
24 (Orange)
1 (Red)
IP
Nominal Output
Power
4 x RJ-11 Female (Black)
1 x RJ-45 Female (Silver) + LEDs (Orange/
Green)
PDU / Bank / Outlet
Switches
Total: 21 x IEC 320 C13 + 3 x IEC 320 C19
Bank 1-1, Outlet 1–8: 7 x C13 + 1 x C19.
Bank 1-2, Outlet 9–16: 7 x C13 + 1 x C19
Bank 2, Outlet 17–24: 7 x C13 + 1 x C19
1 x 4-pin Dry Contact
LAN
LEDs
PE8324B / J
24
100–240V~; 50–60Hz; 24A (UL), 30A (Max.)
0–50oC
-20–60oC
0–80% RH Non-condensing
Housing
Metal
Weight
6.5 kg
Dimensions (L x W x H)
177.50 x 6.60 x 4.40 cm
71
eco PDU PE Series User Manual
PE7324G / PE8324G
Function
Power Outlets
Connectors
PE7324G
Direct
Power Cord
Power
Outlets
1 x IEC 309 32A
IEC
Environment Sensors
Door Sensor
Outlet Status
NA
PDU / Bank / Outlet
2-digit 7-segment (Orange)
Current / Volt / P.D. / Sensor1–
Sensor4 /
FW Upgrade
Current / Volt / P.D. / IP /
Sensor1–Sensor4
Door Open
Reset
1 x Pushbutton
2 x Pushbutton
1 x Semi-recessed Pushbutton
Power
2 x Non-fuse Breaker
Nominal Input Power
100–240V~; 50–60Hz; 32A
Nominal Input/Output Voltage
200–240 VAC
Power Capacity
7.36kW
Per Port
IEC 320 C19
IEC 320 C13
Total
Operating Temperature
Storage Temperature
Humidity
100–240V~; 50–60Hz; 15A (TUV), 16A (Max.)
100–240V~; 50–60Hz; 10A
100–240V~; 50–60Hz; 30A (TUV), 32A (Max.)
0–40oC
-20–60oC
0–80% RH Non-condensing
Housing
Metal
Weight
6.5 kg
Dimensions (L x W x H)
72
7 (Green)
1 (Blue)
LED Display Select
PDU / Bank / Outlet Select
Physical
Properties
3 (Green)
3-digit 7-segment (Orange)
1 (Green)
Power
Environment
24 (Orange)
1 (Red)
IP
Nominal Output
Power
4 x RJ-11 Female (Black)
1 x RJ-45 Female (Silver) + LEDs (Orange/
Green)
PDU / Bank / Outlet
Switches
Total: 21 x IEC 320 C13 + 3 x IEC 320 C19
Bank 1-1, Outlet 1–8: 7 x C13 + 1 x C19.
Bank 1-2, Outlet 9–16: 7 x C13 + 1 x C19
Bank 2, Outlet 17–24: 7 x C13 + 1 x C19
1 x 4-pin Dry Contact
LAN
LEDs
PE8324G
24
177.50 x 6.60 x 4.40 cm
Appendix
Administrator Login Failure
If you are unable to perform an Administrator login (because the Username and
Password information has become corrupted, or you have forgotten it, for
example), you can clear the login information with the following procedure:
1. Power off the eco PDU and remove its housing.
2. Short the jumper labeled J1 (PIN5 and PIN6).
J1
3. Power on the eco PDU.
4. After the beep indicates successfully powered on, power off the switch.
5. Remove the jumper cap from J1.
6. Close the housing and start the eco PDU.
After you start, you can use the default Username and Password to log in.
73
eco PDU PE Series User Manual
Limited Warranty
ATEN warrants this product against defects in material or workmanship for a period of one (1) year
from the date of purchase. If this product proves to be defective, contact ATEN's support
department for repair or replacement of your unit. ATEN will not issue a refund. Return requests
can not be processed without the original proof of purchase.
When returning the product, you must ship the product in its original packaging or packaging that
gives an equal degree of protection. Include your proof of purchase in the packaging and the RMA
number clearly marked on the outside of the package.
This warranty becomes invalid if the factory-supplied serial number has been removed or altered
on the product.
This warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse,
abuse, negligence or modification of any part of the product. This warranty does not cover damage
due to improper operation or maintenance, connection to improper equipment, or attempted repair
by anyone other than ATEN. This warranty does not cover products sold AS IS or WITH FAULTS.
IN NO EVENT SHALL ATEN'S LIABILITY EXCEED THE PRICE PAID FOR THE
PRODUCT. FURTHER, ATEN SHALL NOT BE RESPONSIBLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE
OF THE PRODUCT, ITS ACCOMPANYING SOFTWARE, OR ITS DOCUMENTATION.
ATEN SHALL NOT IN ANY WAY BE RESPONSIBLE FOR, WITHOUT LIMITATION, LOSS
OF DATA, LOSS OF PROFITS, DOWNTIME, GOODWILL, DAMAGE OR REPLACEMENT
OF EQUIPMENT OR PROPERTY, AND ANY EXPENSES FROM RECOVERY,
PROGRAMMING, AND REPRODUCTION OF ANY PROGRAM OR DATA.
ATEN makes no warranty or representation, expressed, implied, or statutory with respect to its
products, contents or use of this documentation and all accompanying software, and specifically
disclaims its quality, performance, merchantability, or fitness for any particular purpose.
ATEN reserves the right to revise or update its product, software or documentation without
obligation to notify any individual or entity of such revisions, or update.
For details about extended warranties, please contact one of our dedicated value added resellers
74
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement