SS 5124 - Munters

SS 5124 - Munters
Natural Ventilation Controller
SS 5124
USER'S MANUAL
66
Aerotech, Inc.
4215 Legion Dr. Mason, MI 48854-1036 USA
Ph. (517) 676-7070 Fax (517) 676-7078
F O R M : QM 1312
August 2001
PRECAUTIONS
TABLE OF CONTENTS
Page
PRECAUTIONS .................................................................. 3
FEATURES ........................................................................ 4
LOCATION OF THE CONTROLS ...................................... 6
Controller Status Leds ...................................................... 7
Internal Switches ............................................................... 7
INSTALLATION .................................................................. 8
Mounting Instructions ......................................................... 8
Connections ..................................................................... 8
Motor Curves .................................................................... 9
Temperature Probes ......................................................... 11
Heating Options ................................................................ 14
CHANGING THE PARAMETER SETTINGS ...................... 15
The Meaning of a Flashing Display ................................... 15
Locking the Parameters Settings ...................................... 15
TEMPERATURE SETTINGS ............................................. 16
Temperature Units ............................................................ 16
Viewing Temperatures ...................................................... 16
Temperature Set Point ...................................................... 19
Temperature Curve ........................................................... 20
VENTILATION SETTINGS ................................................. 24
Cooling Operation............................................................. 24
Minimum Ventilation Cycle ................................................ 28
Ventilation Settings ........................................................... 30
Minimum Ventilation Speed Curve .................................... 34
Mist Cooling ..................................................................... 39
NATURAL VENTILATION .................................................. 42
Principle of Operation ....................................................... 42
Curtain Operating Time Compensation ............................. 43
Settings ............................................................................ 44
HEATER SETTINGS .......................................................... 47
Staged Heaters ................................................................ 47
Zoned Heaters .................................................................. 49
TEST MODE ....................................................................... 52
ALARM SETTINGS ............................................................ 53
TROUBLESHOOTING GUIDE ........................................... 55
TECHNICAL SPECIFICATIONS ........................................ 60
FACTORY SETTINGS ........................................................ 61
2 QM 1312.rev.05
We strongly recommend installing supplementary natural
ventilation, a failure alarm system as well as a back-up thermostat on at least one cooling stage (refer to the wiring
diagram enclosed with this user's manual to connect the thermostat).
Although fuses at the input and outputs of the controller protect
its circuits in case of an overload or overvoltage, we
recommend installing an additional protection device on the
supply circuit as well as an external relay on all ON-OFF stages to prolong the life of the controller.
The room temperature where the controller is located MUST
ALWAYS REMAIN BETWEEN 32°F AND 104°F (0°C TO 40°C).
To avoid exposing the controller to harmful gases or excessive humidity, it is preferable to install it in a corridor.
DO NOT SPRAY WATER ON THE CONTROLLER
FOR CUSTOMER USE
Enter below the serial number located
on the side of the controller and retain
this information for future reference.
Model number:
Serial number:
Date installed:
___SS 5124___
_____________
_____________
QM 1312.rev.05
3
SS 5124
FEATURES
The SS 5124 is an electronic device used for environmental control in livestock buildings. It allows the user to maintain a specified target temperature by controlling the operation of ventilation and heating equipment. One
stage of variable speed cooling fans, two stages of constant-speed cooling
fans, as well as curtains, foggers and heaters can be connected to the
controller.
FULL-SPEED FAN START-UP
The main features of the SS 5124 are as follows:
FOUR INDEPENDENT TEMPERATURE PROBE INPUTS
THREE-DIGIT DISPLAY
A three-digit display provides a high level of accuracy, allowing the user to
specify a temperature to within one tenth of a degree (in Fahrenheit or Celsius units).
In order to overcome the inertia of the ventilation system components and
de-ice the fan blades in cold weather conditions, the controller supplies
maximum voltage to the variable speed fans for 2 seconds immediately
following each start-up.
Up to four temperature probes can be connected to the controller in order to
obtain a more accurate reading of the average room temperature and a
faster reaction time.
OUTSIDE TEMPERATURE COMPENSATION ON CURTAIN SPEED
PILOT LIGHTS
Curtain opening and closing times can be adjusted as a function of outside
temperature.
Pilot lights indicating the state of outputs allow the user to monitor the
operation of the system without having to enter the building.
FLOATING FAN STAGE
MINIMUM VENTILATION CYCLE
When ventilation is not required for cooling, the first stage fans can be operated either continuously or intermittently to reduce the level of humidity and
supply oxygen to the room.
TEMPERATURE AND MINIMUM VENTILATION SPEED CURVES
The controller can be set to automatically change the temperature set point
and the minimum ventilation speed over a given period of time in accordance
with the user's requirements by specifying a temperature curve and a minimum ventilation speed curve with up to six different points each.
CHOICE OF FIVE MOTOR CURVES
The variation in motor speed resulting from a change in voltage will depend
on the make and capacity of the motor. In order to achieve a high degree of
compatibility between controller and motor, the user can choose from among
five different motor curves, thus ensuring that the correct voltage is supplied.
ZONED OR STAGED HEATERS
4
QM 1312.rev.05
One of the on/off ventilation stages can be operated either before or after the
curtains.
OVERLOAD AND OVERVOLTAGE PROTECTION
Fuses are installed at the input and outputs of the controller to protect its
circuitry in the case of an overload or overvoltage.
COMPUTER CONTROL
The controller can be connected to a computer, thus making it possible to
centralize the management of information and diversify control strategies.
CONTROL OF AIR INLET MOVEMENT USING THE SB 2000
If the SS 5124 is used in combination with a SB 2000 controller, the movement of the air inlets can be coordinated with the operation of the stage 1
fans using a potentiometer located on the curtain machine or baffle actuator. This allows the air inlets to be adjusted correctly, without the influence
of uncontrollable factors such as wind or air from adjoining rooms.
HIGH/LOW TEMPERATURE ALARM OUTPUT
QM 1312.rev.05
5
SS 5124
LOCATION OF THE CONTROLS
CONTROLLER STATUS LEDS
LED
ME AN IN G
S TAGE S 1 -2
F L A S H E S WH E N S TA G E 1 F A N S A R E O N . T U R N S O N WH E N S TA G E
2 FA NS A RE ON.
C U R TAIN S
F L A S H E S W H E N C U R T A I N S A R E C L O S I N G. T U R N S O N W H E N
C U R T A I N S A R E O P E N I N G.
S TAGE 4
T U R N S O N WH E N S TA G E 4 F A N S A R E O N .
S TAGE 5 OR 3
T U R N S O N WH E N S TA G E 5 O R S TA G E 3 F A N S A R E O N .
S TAGE 6
H E AT E R B
T U R N S O N WH E N S TA G E 6 F A N S O R H E A T E R B U N IT S A R E O N .
S TAGE 7
H E AT E R A
T U R N S O N WH E N S TA G E 7 F A N S O R H E A T E R A U N IT S A R E O N .
T E M P. C U R V E
F L A S H E S WH E N TH E TE M P E R A TU R E C U R V E IS A C TIV A TE D .
TU R N S O N WH E N TH E M IN IM U M V E N TIL A TIO N S P E E D C U R V E IS
ALSO ON.
D E F. P R O B E /
ALARM
F L A S H E S WH E N A D E F E C TIV E P R O B E IS D E TE C TE D . TU R N S O N
WH E N A N A L A R M IS D E TE C TE D .
INTERNAL SWITCHES
ON
1
2
3
4
5
6
7
8
9 10 11 12
The internal switches are located on the inside of the front cover. When
the controller is shipped from the factory, all the switches are set to OFF.
S E T T IN G S
$
(
5
2
7
(
&
+
,1
&
0
D
V
R
Q
0
66
,
8
6
$
6
QM 1312.rev.05
#
OFF
ON
1
UNLOC K E D PA RA ME TE RS
LOC K E D PA RA ME TE RS
2
FA HRE NHE IT D E GRE E S
C E LS IUS D E GRE E S
3
NO HE ATE RS
HE ATE RS
4
1 HE ATE R
2 HE ATE RS
5
S TA GE D HE ATE RS
ZONE D HE ATE RS
C URTA IN C OMP E NS ATION ON
6
C URTA IN C OMP E NS ATION OFF
7
NO OUTS ID E P ROB E
OUTS ID E P ROB E
8
S TA GE 5 OP E RATE S A FTE R
S TA GE 4
S TA GE 5 MOV E S TO S TA GE 3 P OS ITION
(B E FORE C URTA INS )
9
RE S E RV E D
10
RE S E RV E D
11
RE S E RV E D
12
RE S E RV E D
QM 1312.rev.05
7
SS 5124
INSTALLATION
MOUNTING INSTRUCTIONS
MOTOR CURVES
Open the latch and lift the cover. Remove the black caps located on each of
the four mounting holes. Mount the enclosure on the wall using four screws.
Be sure the electrical knockouts are at the bottom of the enclosure in order
to prevent water from entering the controller. Insert the screws in the mounting
holes and tighten. Fasten the four black caps provided with the controller onto
the four mounting holes. The enclosure must be mounted in a location that
will allow the cover to be completely opened right up against the wall.
The relationship between the voltage supplied to a motor and its operating
speed is described by a motor curve. This curve varies with the make and
capacity of the motor. The various motors available in the industry have been
divided into five categories and the controller has been programmed with a
different motor curve for each of these categories. To ensure that the
controller supplies the correct voltages, an appropriate curve must be
selected for Stage 1 according to the type of fan motors used (see table on
following page).
CONNECTIONS
To connect the controller, refer to the wiring diagram enclosed with this user's
manual.
n
Set the voltage switch to the appropriate voltage.
n
Use the electrical knockouts provided at the bottom of the enclosure.
Do not make additional holes in the enclosure, particularly on the top
of the enclosure when using a SL 1400 communication board.
n
For the heating stages, it may be necessary to install a transformer in
order to supply the appropriate voltage to the heating unit.
ALARM CONNECTION: There are two types of alarms on the market. One
type activates when current is cut off at its input, whereas the other activates
when current is supplied at its input. For an alarm of the first type, use the NO
terminal as shown on the wiring diagram. For an alarm of the second type, use
the NC terminal.
!
WARNING
8
Selecting a Motor Curve
Refer to the list of motors on the following page to determine which type (1
to 5) is appropriate for the motors used.
n
Set the selection knob to
STAGE 1 — BANDWIDTH/
TIMER. The Stage 1 bandwidth is
displayed, alternating with the
letters "bd".
n
Press the push-button three times.
The currently selected type is
displayed, alternating with the
letters "tYP".
n
Use the adjustment knob to adjust the type to the desired value.
n
Return to the Stage 1 bandwidth display by pressing the push-button.
ALL WIRING MUST BE DONE BY AN AUTHORIZED ELECTRICIAN
AND MUST COMPLY WITH APPLICABLE CODES, LAWS AND
REGULATIONS. BE SURE POWER IS OFF BEFORE DOING ANY
WIRING TO AVOID ELECTRICAL SHOCKS AND EQUIPMENT DAMAGE.
QM 1312.rev.05
QM 1312.rev.05
9
SS 5124
SS 5124
TEMPERATURE PROBES
AT14Z, AT14F, AT14G
Connecting the Probes
The controller is supplied with one room probe connected to input # 1. Three
additional probes can be connected to inputs # 2, 3 and 4 and an outside
probe can be connected to input # 5 (see wiring diagram enclosed). If zoned
heating is used, Heater A uses probes 1 & 2 and Heater B uses probes 3 &
4. If staged heating is used, the average temperature from activated probes
# 1, 2, 3 and 4 is used. Ventilation stages use the average temperature from
all indoor probes.
CAUTION: Probes operate at low voltage and are isolated from the supply.
Be sure that probe cables remain insulated from all high voltage sources. In
particular, do not route the probe cables through the same electrical knockout
as other cables. Do not connect the shield from the probe cable to an input
or a ground.
2
Extending the Probes
Each probe can be extended up to 500 feet (150 meters). To extend a probe:
30
40
40
30
65
65
45
45
Minimum
Speed
130
117
107
101
101
101
42
81
Minimum
Voltage
Output
n
1250
1250
600
140
110
120
50
50
CFM
at 0.05"
S.P.
Control Settings
1
Motor
Curve
1
1
1
3
3
4
5
Minimum Speed Setting and Motor Curve Selection
14"
AT15AP, AT15SP
Model Numbers
15"
AT16Z, AT16F, AT16G
AT09Z1, AT10SP1, AT10AP1 (120 VAC)
16"
AT18Z, AT18F, AT18G, GB18
9"
18"
AT24Z, AT24F, AT24G, GB24
Fan
Dia.
24"
AT36Z, AT36ZB1, AT36G1, AT36GB1
AT09Z2, AT10SP2, AT10AP2 (240 VAC)
36"
The above values assume the following conditions unless noted otherwise:
1) Input Voltage: 240 VAC
2) Static Pressure: 0.05" S.P.
3) Fan Accessories: Hood, Guard and Shutter if applicable.
For configurations or requirements other than above, refer to Form QM1065.
1
CAUTION: Do not run probe cables next to other power cables. When
n
Use a shielded cable of outside diameter between 0.245 and 0.260 in
(6.22 and 6.60 mm) (the cable dimensions should not be under 18
AWG) to ensure the cable entry is liquid tight. Do not ground the
shielding.
It is preferable to solder the cable joint to ensure a proper contact
between the two cables.
crossing over other cables, cross at 90°.
10 QM 1312.rev.05
QM 1312.rev.05
11
SS 5124
SS 5124
nating with the letter "P".
3
Installing the Outside Probe
n
Run the outside probe cable on the north side of the building, 6 ft (2 m)
below the eave, inside a pale colored conduit. Avoid installing the
probe in direct sunlight or exposed to the rain.
n
Be sure the probe cable is isolated from sheet metal or any other
conductive material.
n
Be sure no cable joint is exposed to air or water.
n
Set internal switch # 7 to ON.
4
For each additional probe connected to the controller:
n
Press the push-button once again. If the probe is not defective, the
letters "PR#" (where # is the number of the input to which the probe is
connected) are displayed, alternating with the temperature measured
by the probe. If the probe is defective, the letters "PR#" are displayed, alternating with the letter "P".
Outside Probe: If the outside probe is
defective, the display shows the letter
"P" when the parameter selection knob
is set to OUTSIDE TEMP.
Defective Probes
Room Probes: If a defective probe is detected, the Defective Probe Pilot
Light turns on. The room temperature shown on the display is then the
average temperature measured by the probes in working condition. The
controller will operate according to this temperature.
To identify the defective probe:
n
Set the selection knob to ROOM
TEMPERATURE . The room temperature is displayed.
n
Press the push-button. If the
probe connected to input # 1 and
supplied with the controller is not
defective, the letters"PR1" are displayed, alternating with the temperature measured by the probe.
If the probe is defective, the letters "PR1" are displayed, alter-
12 QM 1312.rev.05
QM 1312.rev.05
13
SS 5124
CHANGING THE PARAMETER SETTINGS
HEATING OPTIONS
THE MEANING OF A FLASHING DISPLAY
Stages 6 and 7 can operate as heating or cooling stages.
ð Set switches # 3 and # 4 to OFF to
use both stages for cooling.
ON
ð Set switch # 3 to ON and switch # 4
to OFF to use Stage 7 for heating and
Stage 6 for cooling.
ð Set switches # 3 and # 4 to ON to
3
4
The display will flash in certain cases and not in others.
The flashing indicates that the
value shown can be adjusted.
A value that is not flashing
cannot be adjusted.
use both stages for heating.
Note that if only one stage is used for heating, it must be Stage 7.
LOCKING THE PARAMETER SETTINGS
Zoned/Staged Heaters: The controller can operate the heaters as zoned
or staged heaters. In the first case, the heaters function independently
according to separate probe readings and each heater system (A and B)
has a separate offset. In the second case, the heaters operate according to
the average temperature from all probes and only one offset is used. Dipswitch
5 is used to configure the heater operation.
ON
The parameter settings can be locked to prevent accidentally modifying
them. When the settings are locked, only the temperature set point and the
Stage 1 minimum ventilation speed can be modified (as long as the temperature curve and the minimum ventilation speed curve are deactivated
respectively).
Set dipswitch # 5 to ON for zoned heating.
n
Set dipswitch # 5 to OFF for staged heating.
Set internal switch # 1 to ON.
To unlock the parameter settings:
5
14 QM 1312.rev.05
To lock the parameter settings:
n
Set internal switch # 1 to OFF.
QM 1312.rev.05
15
SS 5124
TEMPERATURE SETTINGS
TEMPERATURE UNITS
Temperatures can be displayed in either Celsius or
Fahrenheit units
n
ON
Press the push-button. The temperature reading from probe 1 is displayed, alternating with the letters "Pr 1".
n
For each additional probe, press the push-button. The temperature
reading from probe x is displayed, alternating with the letters "Pr x",
etc.
n
Press the push-button once again to display the state of probe 1 , i.e.
ON / OFF. When a probe is activated, it is used in the calculation of
the average room temperature.
n
Use the adjustment knob to change the state of the probe.
n
For each additional probe, press the push-button. The state of probe
is displayed, alternating with the letters "Pr x", etc.
Set internal switch # 2 to the desired position:
• ON to display temperatures in Celsius units.
• OFF to display temperatures in Fahrenheit units.
2
VIEWING TEMPERATURES
The readout can display values from
-40.0oF to 120oF ( -40.0oC to 48.9oC).
When the temperature drops below
-9.9 degrees, the negative sign is
displayed separately, alternating with
the numerical value.
1
n
Viewing the Room Temperature
Notes:
i) At least one probe must be activated at all times. If only one probe remains
active, the controller will lock the on/off switch for that probe.
ii) The display returns to the average room temperature after one minute.
iii) Initially, only probe one is activated.
The room temperature is the average value of all temperatures measured by
activated probes in proper operating condition.
n
2
Set the selection knob to ROOM TEMPERATURE / PROBE TEMP.
The room temperature is displayed.
Viewing the Probe Temperatures
The controller can display probe temperatures individually. Probes can also
be turned on or off to control the temperature in different parts of the building.
n
3
Viewing the Outside Temperature
The outside temperature can be viewed only if a probe is connected to input
# 5. If no probe is connected, the word "OFF" is displayed.
n
Set selection knob to OUTSIDE
TEMP. / SETTINGS. The outside
temperature is displayed.
Set selection knob to ROOM TEMPERATURE / PROBE TEMP. The
average room temperature is displayed.
16 QM 1312.rev.05
QM 1312.rev.05
17
SS 5124
SS 5124
4
Viewing Minimum / Maximum Temperatures
The minimum and maximum temperatures are the lowest and highest temperature values recorded since the last reset. Temperatures values are
averaged over all active probes.
n
Set the selection knob to ROOM TEMPERATURE / PROBE TEMP.
or OUTSIDE TEMP. / SETTINGS. The room or outside temperature
is displayed.
n
Turn the adjustment knob clockwise by one notch. The minimum
temperature flashes on the display, alternating with the letters "Lo".
n
Turn the adjustment knob clockwise one notch further. The maximum temperature flashes on the display, alternating with the letters
"Hi".
n
Turn the adjustment knob clockwise a third notch. The room or outside temperature is displayed again.
n
For each individual probe, press the push-button. The temperature
reading from probe x is displayed, alternating with the letters "Pr x"
and the on/off state of the probe.
n
Turn the adjustment knob clockwise by one notch. The minimum is
displayed, alternating with the letters "Lo".
n
Turn the adjustment knob clockwise one notch further. The maximum temperature is displayed, alternating with the letters "Hi".
n
Turn the adjustment knob clockwise a third notch. The probe temperature is displayed again.
n
For each additional probe, press the push-button. The temperature
reading from probe x is displayed, alternating with the letters "Pr x"
and the on/off state of the probe, etc.
18 QM 1312.rev.05
NOTE: If you let the display flash for more than 10 seconds, the controller
resets the minimum and maximum temperatures currently in memory (the
display stops flashing to indicate that the reset has been done).
TEMPERATURE SET POINT
The temperature set point is the target
room temperature. It can be adjusted
between -40.0°F and 99.9°F (-40.0°C
and 37.7°C).
Adjusting the Temperature Set Point
n
Set the selection knob to SET POINT / TEMP. CURVE.The current set
point flashes on the display.
n
Use the adjustment knob to adjust the set point to the desired value.
NOTE: The temperature set point can be adjusted only if the temperature
curve is deactivated (see following section).
QM 1312.rev.05
19
SS 5124
SS 5124
TEMPERATURE CURVE
1
The user can define a temperature curve to adjust the set point automatically
over a given time period.
n
Set the selection knob to SET
POINT / TEMP. CURVE. The
current temperature set point
flashes on the display.
n
Press the push-button. The word OFF is displayed indicating that the
termperature curve is deactivated. If this is not the case, see below to
deactivate the curve.
○
○
d4
d25
d35
d50
○
○
○
○
d70
○
Repeat the following steps for each of the six points:
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Temperature
T o1
T o2
T o3
T o4
T o5
T o6
Specifying the Curve
d80 Days
A curve is defined using six points. Each point specifies a day number and
a set point for that day. Once the points of the curve are defined, the curve
must be activated. The controller will change the temperature set point every
hour in a linear fashion between consecutive points of the curve. When the
last point of the curve is reached, the temperature set point for that day is
maintained until the curve is reactivated.
NOTES :
i) All six points of the curve must be specified. If six points are not needed,
repeat the last temperature value for each unnecessary point.
ii) Certain restrictions apply to reduce the risk of errors:
- The highest possible day number is 99.
- Decreasing day numbers are not allowed.
n
Press the push-button once again. The word "day" is displayed,
alternating with a day number.
n
Using the adjustment knob, set the day number to the desired value.
n
Press the push-button once again. The current temperature set point
is displayed, alternating with the word "set".
n
Using the adjustment knob, adjust the set point to the desired value.
Once the six points of the curve have been specified, activate the curve as
explained below.
NOTE: Make sure the temperature curve is deactivated before specifying
new points (see below).
- Increasing temperatures are not allowed.
- The temperature variation cannot exceed 3°F (1.6°C) per day.
20 QM 1312.rev.05
QM 1312.rev.05
21
SS 5124
SS 5124
2
Activating the Temperature Curve
If you have just finished specifying the points on the curve:
n
n
n
Press the push-button once again. The word OFF flashes on the
display.
Turn the adjustment knob clockwise one notch. The word ON flashes
on the display, the Temperature Curve Pilot Light flashes, indicating
that the temperature curve is now activated.
Set the selection knob to ROOM TEMPERATURE.
If you have previously defined the points on the curve:
3
Viewing Current Set Point and Day Number
When the temperature curve is activated, the current temperature set point
and day number can be viewed at any time. The current day number can
also be adjusted in order to move forward or backward on the temperature
curve.
n
Set the selection knob to SET POINT / TEMP. CURVE. The current
temperature set point flashes on the display.
n
Press the push-button. The current day number is displayed.
n
Use the adjustment knob to set the day number to the desired
value.
4
Deactivating the Temperature Curve
n
Set the selection knob to SET POINT / TEMP. CURVE. The current
temperature set point flashes on the display.
Press the push-button. The word OFF appears on the display.
n
Press the push-button to display the points of the curve actually defined until the word ON appears (fourteen clicks).
n
Press the push-button to display the points of the curve currently
defined until the word OFF appears (thirteen clicks).
n
n
Turn the adjustment knob clockwise one notch. The word ON flashes
on the display and the Temperature Curve Pilot Light flashes, indicating that the temperature curve is now activated.
Turn the adjustment knob counterclockwise one notch. The word
OFF flashes on the display and the Temperature Curve Pilot Light
turns off indicating that the temperature curve is now deactivated.
n
Set the selection knob to ROOM TEMPERATURE.
n
Set the selection knob to SET POINT / TEMP. CURVE. The current
value of the temperature set point flashes on the display.
n
n
Set the selection knob to ROOM TEMPERATURE.
22 QM 1312.rev.05
QM 1312.rev.05
23
SS 5124
VENTILATION SETTINGS
COOLING OPERATION
• At Set Point + Bandwidth: the stage 1 decrease in speed as the tem-
The SS 5124 controls one stage of variable-speed fans (Stage 1), three
stages of constant-speed fans (Stages 2, 4 and 5), two optional stages of
constant-speed fans (Stages 6 - 7), as well as curtains for natural ventilation (Stage 3). The last cooling stage can be operated as a mist stage by
setting the time on value to a non-zero value.
• At Set Point: stage 1 fans stop operating continuously and operate
perature falls.
according to the minimum ventilation cycle at minimum speed.
• When room temperature < Set Point, stage 1 fans run at minimum speed
• At Curtain Opening Temp.: curtains open according to timer settings.
• At Stage 4 Starting Temp.: stage 4 fans start running.
• At Stage 5 Starting Temp.: stage 5 fans start running.
• At Stage 6 Starting Temp.: stage 6 fans start running.
• At Stage 7 Starting Temp.: stage 7 fans start running.
Start
Temp
Stage 7
Start
Temp
Stage 4
1.5 oF
Start
Temp
Stage 5
1.5 oF
Bandwidth
Stage 1
If the room temperature falls:
Start Temp Closing Temp Opening
Stage 2
Curtains
Temp
Curtains
• At Stage 2 Starting Temp.: stage 2 fans start running.
• At Stage 7 Starting Temp. - 1.5 F: stage 7 fans return to a stop.
24 QM 1312.rev.05
Minimum
Ventilation
Cycle
STAGE 1
STAGE 2
STAGE 4
• At Stage 2 Starting Temp. - 1.5 F: stage 2 fans return to a stop.
STAGE 5
• At Curtain Closing Temp.: curtains close according to timer settings.
STAGE 6
• At Stage 4 Starting Temp. - 1.5 F: stage 4 fans return to a stop.
STAGE 7
• At Stage 5 Starting Temp. - 1.5 F: stage 5 fans return to a stop.
Ventilation
Level
• At Stage 6 Starting Temp. - 1.5 F: stage 6 fans return to a stop.
Temperature
Set Point
• At Set Point + Bandwidth: stage 1 fans reach full speed.
1.5 oF
ventilation cycle and increase in speed as the room temperature rises.
1.5 oF
• At Set Point: stage 1 fans stop operating according to the minimum
MODE 1 OPERATION DIAGRAM
according to the minimum ventilation cycle.
Curtains open
in timer mode
• When room temperature < Set Point, stage 1 fans run at minimum speed
Curtains
close
in timer mode
If room temperature rises:
Start
Temp
Stage 6
1.5 oF
Mode 1: The SS 5124 is in mode 1 when internal switch # 8 is in the OFF
position. In this mode, Stage 5 constant-speed fans operate as expected
after Stage 4 fans have been turned on. The diagram on the following page
illustrates this mode:
Temp.
according to the minimum ventilation cycle.
QM 1312.rev.05
25
SS 5124
SS 5124
Mode 2: The SS 5124 is in mode 2 when internal switch # 8 is in the ON
position. In this mode, Stage 5 constant-speed fans move to the Stage 3
position and operate after Stage 2 fans have been turned on (before the
curtains start opening). The following diagram illustrates this mode:
Start
Temp
Stage 7
Start
Temp
Stage 6
• At Set Point + Bandwidth: stage 1 fans reach full speed.
• At Stage 2 Starting Temp.: stage 2 fans start running.
• At Stage 3 Starting Temp.: stage 3 fans start running.
• At Curtain Opening Temp.: curtains open according to timer settings.
• At Stage 4 Starting Temp.: stage 4 fans start running.
• At Stage 6 Starting Temp.: stage 6 fans start running.
• At Stage 7 Starting Temp.: stage 7 fans start running.
If the room temperature falls:
• At Stage 7 Starting Temp. - 1.5 F: stage 7 fans return to a stop.
• At Stage 6 Starting Temp. - 1.5 F: stage 6 fans return to a stop.
• At Stage 4 Starting Temp. - 1.5 F: stage 4 fans return to a stop.
• At Curtain Closing Temp.: curtains close according to timer settings.
• At Stage 3 Starting Temp. - 1.5 F: stage 3 fans return to a stop.
Temperature
Set Point
Bandwidth
Stage 1
1.5 oF
Start Temp
Stage 2
1.5 oF
Start
Temp
Stage 3
Closing Temp Opening
Curtains
Temp
Curtains
1.5 oF
according to the minimum ventilation cycle.
ventilation cycle and increase in speed as the room temperature rises.
Start
Temp
Stage 4
1.5 oF
• When room temperature < Set Point, stage 1 fans run at minimum speed
• At Set Point: stage 1 fans stop operating according to the minimum
Temp.
1.5 oF
Curtains open
in timer mode
Curtains
close
in timer mode
MODE 2 OPERATION DIAGRAM
• At Stage 2 Starting Temp. - 1.5 F: stage 2 fans return to a stop.
• At Set Point + Bandwidth: the stage 1 decrease in speed as the temperature falls.
Minimum
Ventilation
Cycle
STAGE 1
STAGE 2
STAGE 3
STAGE 4
STAGE 6
• At Set Point: stage 1 fans stop operating continuously and operate
STAGE 7
Ventilation
Level
26 QM 1312.rev.05
If the room temperature rises:
according to the minimum ventilation cycle at minimum speed.
• When room temperature < Set Point, stage 1 fans run at minimum speed
according to the minimum ventilation cycle.
QM 1312.rev.05
27
SS 5124
SS 5124
MINIMUM VENTILATION CYCLE
1
When the room temperature is below the set point, the Stage 1 fans operate
according to the minimum ventilation cycle. Running the fans even though
ventilation is not required for a cooling purpose is useful to reduce humidity
levels and supply oxygen to the room. It also prevents the fans from freezing
in winter.
The minimum speed can be adjusted between 10 and 100% of the full speed
of the fans.
n
Set the selection knob to STAGE
1 — MINIMUM SPEED/CURVE.
The current minimum speed for
Stage 1 flashes on the display.
n
Use the adjustment knob to adjust the minimum speed to the desired value.
TIME ON
STAGE 1
STAGE 1 — MIN. SPEED
OFF
TIME OFF
STAGE 1
During time on, the Stage 1 fans run at Stage 1 minimum speed. The Stage
1 Pilot Light turns on. During time off, the Stage 1 fans do not run. The Stage
1 Pilot Light turns off. The Stage 1 minimum speed can also be defined by
a speed curve (see below).
NOTE: The controller supplies maximum voltage to the variable-speed fans
for 2 seconds immediately following each start-up.
NOTE: The minimum speed can be adjusted only if the minimum speed
curve is deactivated or if the minimum speed curve is activated but not currently operating (see below).
2
2. To stop the fans, set time on to zero and time off to any value.
3. To run the fans intermittently, set time on to the desired running time
and time off to the desired off time.
Adjusting Stage 1 Time On and Time Off
n
Set the selection knob to STAGE 1 — BANDWIDTH / TIMER. The
current bandwidth for Stage 1 is displayed, alternating with the letters
"bd".
n
Press the push-button. The current time on for Stage 1 flashes on
the display, alternating with the letters "On".
n
Use the adjustment knob to adjust time on to the desired value.
n
Press the push-button. The current time off for Stage 1 flashes on the
display, alternating with the letters "Off".
n
Use the adjustment knob to adjust time off to the desired value.
Minimum Ventilation Cycle Settings
1. To run the fans continuously at minimum speed, set time off to zero and
time on to any value other than zero.
Adjusting Minimum Speed
Time on and Time Off can be adjusted between 0 and 900 seconds, in
increments of 15 seconds.
28 QM 1312.rev.05
QM 1312.rev.05
29
SS 5124
SS 5124
VENTILATION SETTINGS
1
Adjusting the Stage 1 Bandwidth
The Stage 1 bandwidth is the temperature
interval within which the Stage 1 variable
speed fans increase or decrease in
speed proportionally to the temperature
(see the diagram above). When this
value is adjusted, all the starting values
for consecutive stages are adjusted by
the same amount. The bandwidth can
be adjusted between 0.5°F and 20.0°F
(0.3°C and 11.1°C).
n
Set the selection knob to STAGE 1 — BANDWIDTH/TIMER. The
current bandwidth is displayed, alternating with the letters "bd".
n
Use the adjustment knob to adjust the bandwidth to the desired value.
2
Adjusting the Stage 1 Hysteresis
The hysteresis is the temperature interval below the set point at which the
fans start operating according to the minimum ventilation cycle. It can be
adjusted between 0.3°F and 2.0°F (0.2°C and 1.1°C).
n
3
The Stage 2 starting temperature is the temperature at which the Stage 2 fans
start running (see the diagram above). The hysteresis is fixed at 1.5oF and
determines when the fans return to a stop. When this value is adjusted, all
the starting values for consecutive stages are adjusted by the same amount.
Stage 2 fans
return to a stop
1.5°F
Differential
Set Point +
bandwidth
n
Press the push-button four times. The current hysteresis is displayed,
alternating with the letters "HYS".
n
Use the adjustment knob to adjust the hysteresis to the desired value.
30 QM 1312.rev.05
Stage 2
Starting
Temperature
Temperature
The differential shown above can go from 0°F to 20.0°F (0°C to 11.1°C). If this
value is less than 1.5°F, the hysteresis is adjusted to the new differential. If
the differential is less than 0.3°F, the hysteresis is set to 0.3°F. Note that if
an SB2000 air inlet controller is being used, the differential must be greater
than 0.5°F in order for Stage 2 to be interpreted correctly.
n
Set the selection knob to STAGE 2 — START TEMP. The current
starting temperature is displayed, alternating with the letters "ST2".
n
Use the adjustment knob to adjust the temperature to the desired value.
4
Set the selection knob to STAGE 1 — BANDWIDTH/TIMER. The
current bandwidth is displayed, alternating with the letters "bd".
Adjusting the Stage 2 Starting Temperature
Adjusting the Stage 3 Starting Temperature
Stage 3 fans are available only if the controller is in Mode 2 (i.e. internal switch
# 8 is ON). Stage 3 fans operate after Stage 2 fans are turned on and before
the curtains start opening. Note that when Stage 3 fans are used, Stage 5
fans are not available (see operation diagram above). The Stage 3 starting
temperature is the temperature at which the Stage 3 fans start running (see
the diagram above). The hysteresis is fixed at 1.5oF and determines when the
fans return to a stop. The difference between the starting temperature and the
Stage 2 starting temperature can go from 0.5°F to 20.0°F (0.3°C to 11.1°C).
QM 1312.rev.05
31
SS 5124
SS 5124
n
Set the selection knob to STAGE 2 — START TEMP. The current Stage
2 starting temperature is displayed, alternating with the letters "ST2".
n
Press the push-button. The current Stage 5 starting temperature is
displayed, alternating with the letters "ST5".
n
Press the push-button. The current Stage 3 starting temperature is
displayed, alternating with the letters "ST3".
n
Use the adjustment knob to adjust the temperature to the desired value.
n
Use the adjustment knob to adjust the temperature to the desired value.
5
Adjusting the Stage 4 Starting Temperature
The Stage 4 starting temperature is the temperature at which the Stage 4 fans
start running (see the diagram above). The hysteresis is fixed at 1.5oF and
determines when the fans return to a stop. The difference between the starting
temperature and the opening temperature of the curtains can go from 0.5°F
to 20.0°F (0.3°C to 11.1°C).
n
Set the selection knob to STAGES 4-5 — START TEMP. The current
Stage 4 starting temperature is displayed, alternating with the letters
"ST4".
n
Use the adjustment knob to adjust the temperature to the desired value.
6
Adjusting the Stage 5 Starting Temperature
Stage 5 fans are available only is the controller is in Mode 1. Stage 5 fans
operate after the curtains start opening. Note that when Stage 5 fans are
used, Stage 3 fans are not available (see operation diagram above). The
Stage 5 starting temperature is the temperature at which the Stage 5 fans
start running (see the diagram above). The hysteresis is fixed at 1.5oF and
determines when the fans return to a stop. The difference between the starting
temperature and the stage 4 starting temperature can go from 0.5°F to 20.0°F
(0.3°C to 11.1°C).
n
7
Adjusting the Stage 6 Starting Temperature
The Stage 6 starting temperature is the temperature at which the Stage 6 fans
start running (see the diagram above). The hysteresis is fixed at 1.5oF and
determines when the fans return to a stop. The difference between the starting
temperature and the stage 5 starting temperature can go from 0.5°F to 20.0°F
(0.3°C to 11.1°C).
n
Set the selection knob to STAGE 6 — START TEMP. The Stage 6
starting temperature is displayed, alternating with the letters "ST6".
n
Use the adjustment knob to adjust the temperature to the desired value.
8
Adjusting the Stage 7 Starting Temperature
The Stage 7 starting temperature is the temperature at which the Stage 7 fans
start running (see the diagram above). The hysteresis is fixed at 1.5oF and
determines when the fans return to a stop. The difference between the starting
temperature and the stage 6 starting temperature can go from 0.5°F to 20.0°F
(0.3°C to 11.1°C).
n
Set the selection knob to STAGE 7 — START TEMP. The Stage 7
starting temperature is displayed, alternating with the letters "ST7".
n
Use the adjustment knob to adjust the temperature to the desired value.
Set the selection knob to STAGES 4-5 — START TEMP. The current
Stage 4 starting temperature is displayed, alternating with the letters
"ST4".
32 QM 1312.rev.05
QM 1312.rev.05
33
SS 5124
SS 5124
Table 1.
MINIMUM VENTILATION SPEED CURVE
The user can define a minimum ventilation speed curve to adjust the Stage
1 minimum speed automatically over a given time period. Each curve is
defined by six points. Each point specifies a day number and a fan speed
for that day. Once the points are defined, the minimum speed curve must
be activated. When the minimum speed curve is activated, the controller
adjusts the Stage 1 minimum speed every hour in a linear fashion between two consecutive points.
STAGE 7
OPERATION
THRESHOLD VALUE
Cooling
''Set Point - 5.0°F (2.8°C)''
''Heater A Starting Temperature - 5.0°F (2.8°C)"
OR
Heating
''Set Point'', if the parameter settings are such that the
preceding value is greater than the set point.
When the last point of the curve is reached, the curve is deactivated. The
controller maintains the minimum speed specified for this point until the
curve is reactivated or until a new single minimum speed is specified using
the first method.
Interaction Between the Temperature Curve and the Minimum Speed Curve
○
○
○
Temperature
or Speed
•
The minimum speed curve can be activated only if the temperature
curve is already activated
•
All points of the minimum speed curve other than the first one are
automatically given day numbers identical to those specified for the
temperature curve. Only the first point of the minimum speed curve
has an adjustable day number. This day number must be greater or
equal to the day number specified for the first point of the temperature
curve and less than the day number specified for the second point of
the temperature curve (see example 1).
○
○
○
d4 d10
d25
d35
○
○
Temperature Curve
○
○
d70
○
○
d50
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Minimum Speed Curve
d80
Days
NOTE:
If the room temperature falls below the threshold value given in table 1, the
fans will begin to run at the minimum speed specified for the first point of
the curve and will continue to do so as long as the room temperature
remains below the set point. When the room temperature rises above the
set point, the fans will return to the current minimum speed, calculated
according to the minimum speed curve.
34 QM 1312.rev.05
EXAMPLE 1
TEMPERATURE CURVE
MINIMUM SPEED CURVE
POINT 1
d5
d5 to d19 (adjustable)
POINT 2
d20
d20 (not adjustable)
QM 1312.rev.05
35
SS 5124
SS 5124
•
When the minimum speed curve is activated, it will effectively be
operating (i.e. the controller will begin to adjust the minimum speed
according to the specified points of the curve) only when the current
day number of the temperature curve reaches the first day number
of the minimum speed curve.
EXAMPLE 2
TEMPERATURE CURVE
MINIMUM SPEED CURVE
Day
Temperature
Day
Speed
POINT 1
d5
90.0 °F
d10
10 %
POINT 2
d20
85.0 °F
d20
20 %
•
If you activated the temperature curve yesterday, the current day number of the temperature curve is d6. Therefore, if you activate the minimum speed curve today, it will effectively be in operation in 4 days,
when the current day number of the temperature curve reaches d10.
In the meantime, the fans will run at the specified single minimum speed (see example 2).
•
n
Repeat the following steps for each of the six points:
n
Press the push-button once again. The word "day" is displayed,
alternating with a day number.
n
For the first point of the curve, use the adjustment knob to adjust
the day number to the desired value. For all other points of the
curve, the day number can not be adjusted.
n
Press the push-button once again. The minimum speed for that
day is displayed, alternating with the letters "SPd".
n
Use the adjustment knob to adjust the minimum speed to the desired value.
NOTES:
i) The minimum speed curve must be deactivated before specifying the
points on the curve (see below).
If you activated the temperature curve six days ago, the current day
number of the temperature curve is d11. Therefore, if you activate the
minimum speed curve today, it will effectively be in operation the moment you activate it. In this case, the current minimum speed will be a
value between 10% and 20%.
1
Press the push-button. The word OFF is displayed, indicating that
the minimum speed curve is deactivated. If this is not the case,
deactivate the curve as described below.
ii) All six points of the curve must be specified. If you do not need
six different points, repeat your last minimum speed for each
unnecessary point of the curve.
iii) Certain restrictions apply to reduce the risk of errors:
• decreasing minimum speeds are not allowed.
Specifying the Minimum Speed Curve
• the minimum speed variation cannot exceed 10% per day.
n
Set the selection knob to STAGE
1 — MINIMUM SPEED / CURVE.
The current minimum speed
flashes on the display.
36 QM 1312.rev.05
2
Activating the Minimum Speed Curve
If you have just finished specifying the points on the curve:
n
Press the push-button once again. The word OFF flashes on the
display.
QM 1312.rev.05
37
SS 5124
SS 5124
n
Turn the adjustment knob clockwise by one notch. The word ON
flashes on the display and the Temperature Curve Pilot Light turns
on, indicating that the minimum speed curve is now activated.
If you have previously specified the points on the curve:
n
Set the selection knob to STAGE 1 — MINIMUM SPEED / CURVE.
The current minimum speed flashes on the display.
n
Press the push-button to display the points of the curve currently
defined until the word OFF appears (thirteen clicks).
n
Turn the adjustment knob clockwise by one notch. The word ON
flashes on the display the Temperature Curve Pilot Light turns on,
indicating that the minimum speed curve is now activated.
MIST COOLING
The last cooling stage can be configured as a mist stage.
The number of
heating stages determines which stage this is.
NUMBER OF HEATING STAGES
0
1
2
MIST STAGE
7
6
5 or 4*
The following diagram sums up the operation of the mist units. If a mist
stage is not needed, time off should be set to zero.
TIME ON
MIST UNITS ON
MIST UNITS OFF
NOTE : When the minimum speed curve is operating, the current Stage 1
minimum speed can be viewed at any time by setting the selection knob to
STAGE 1 — MINIMUM SPEED / CURVE. The current day number can then
be viewed by pressing the push-button.
3
Deactivating the Minimum Speed Curve
n
Set the selection knob to STAGE 1 — MINIMUM SPEED / CURVE.
The current minimum speed flashes on the display.
n
Press the push-button to display the points of the curve currently
defined until the word ON appears (fourteen clicks).
n
Turn the adjustment knob counterclockwise by one notch. The word
OFF flashes on the display and the Temperature Curve Pilot Light
starts blinking, indicating that the minimum speed curve is now
deactivated.
38 QM 1312.rev.05
TIME OFF
The diagram below illustrates the operation of a mist stage.
Mist units
turn off
Mist units operate
in timer mode
1.5oF
Mist
OFF
Set Point
Start
Temp.
Room
Temperature
* If the controller is in Mode 1 (see the section "Ventilation Settings"), the
mist stage when 2 heating stages are used is Stage 5. If the controller is in
Mode 2, the mist stage when 2 heating stages are used is Stage 4.
QM 1312.rev.05
39
SS 5124
SS 5124
Adjusting the Mist Starting Temperature and Timer
The mist starting temperature is bounded below by the starting temperature
of the preceding cooling stage + 0.5oF (0.3oC) and above by the starting
temperature of the preceding cooling stage + 20.0oF (11.1oC). The time on
and time off parameters can take values from 0 to 60 minutes.
n
Press the push-button. The mist time on is displayed, alternating with
the word "On".
n
Use the adjustment knob to set time on to the desired value.
n
Press the push-button. The mist time off is displayed, alternating with
the word "OFF".
n
Use the adjustment knob to set time off to the desired value.
If Stage 4 is the mist stage:
n
Set the selection knob to
STAGES 4-5 — START TEMP.
The stage 4 starting temperature is displayed, alternating
with the letters "ST4".
n
Use the adjustment knob to set the starting temperature to the desired
value.
n
Press the push-button. The mist time on is displayed, alternating with
the word "On".
n
Use the adjustment knob to set time on to the desired value.
n
Press the push-button. The mist time off is displayed, alternating with
the word "OFF".
n
Use the adjustment knob to set time off to the desired value.
If Stage 5 is the mist stage:
n
Set the selection knob to STAGES 4-5 — START TEMP. The stage
4 starting temperature is displayed, alternating with the letters "ST4".
n
Press the push-button. The Stage 5 starting temperature is displayed,
alternating with the letters "ST5".
n
Use the adjustment knob to set the starting temperature to the desired
value.
QM 1312.rev.05
40
If Stage 6 or 7 is the mist stage:
n
Set the selection knob to
STAGE 6 — START TEMP or
STAGE 7 — START TEMP.
The mist starting temperature
is displayed, alternating with
the letters "ST6" or "ST7".
n
Use the adjustment knob to set
the starting temperature to the
desired value.
n
Press the push-button. The mist time on is displayed, alternating with
the word "On".
n
Use the adjustment knob to set time on to the desired value.
n
Press the push-button. The mist time off is displayed, alternating with
the word "OFF".
n
Use the adjustment knob to set time off to the desired value.
QM 1312.rev.05
41
SS 5124
NATURAL VENTILATION
PRINCIPLE OF OPERATION
The curtains close intermittently according to the time on and time off
settings:
TIME ON
CLOSE
Curtains open
in timer mode
Curtains close
in timer mode
0.3 F
0.3 F
Curtains
STOP CLOSING
o
o
TIME OFF
NOTE: The curtains do not open if the current outside temperature is
below the Low Outside Temperature Limit as defined below.
OFF
Set Point = 75oF
89oF
79oF
Room
Temperature
In the example above, when the temperature rises to 89oF, the curtains
begin to open and continue to do so until fully open if the temperature
remains above this point. If the temperature falls to 88.7oF, the curtains
stop opening.
The curtains open intermittently according to the time on and time off settings:
TIME ON
Normal Mode (Without Compensation)
The curtains open and close intermittently according to the specified opening time, closing time and time off, as described on the preceding pages.
There is no outside temperature compensation. To operate the controller in
this mode, set internal switch # 6 to OFF.
Progressive Mode (With Compensation)
OPEN
STOP OPENING
TIME OFF
If an SB2000 is being used, the air inlets return to the first programmed
point (0%) when the curtains open. When the temperature falls to 79oF, the
curtains begin to close and continue to do so until fully closed if the temperature remains below this point. If the temperature rises to 79.3oF, the
curtains stop closing.
42 QM 1312.rev.05
CURTAIN OPERATING TIME COMPENSATION
The controller can use the current outside temperature to adjust the opening
and closing times of the curtains. To use this feature, set internal switch # 6
to ON. Note that internal switch # 7 must also be ON and an outside probe
must be connected to input # 5 in order for the compensation to work.
Temperature Rises:
When the curtains open, the controller increases TIME ON by 5% for every
1°F (0.6°C) in the compensation interval (i.e. an interval of 3oF means a 15%
increase). The TIME OFF is decreased by the same amount.
QM 1312.rev.05
43
SS 5124
SS 5124
Compensation
Interval
Outside
Diff.
Current Outside
Set Point Temperature
n
Set the selection knob to CURTAINS - OPEN/CLOSE TEMP/
TIMER. The current curtain
opening temperature flashes on
the display, alternating with the
letters OPE.
n
Use the adjustment knob to set
the opening temperature to the
desired value.
n
Press the push-button. The current curtain closing temperature flashes
on the display, alternating with the letters CLO.
n
Use the adjustment knob to set the closing temperature to the desired
value.
Temperature
The higher the outside temperature, the time on increases, causing the
curtains to open faster.
Temperature Falls:
When the curtains close, the controller increases TIME ON by 5% for every
1°F (0.6°C) in the compensation interval (i.e. an interval of 3oF means a
15% increase). TIME OFF is decreased by the same amount.
The lower the outside temperature, time on increases, causing the curtains
to close faster.
Compensation
Interval
Current Outside
Temperature
2
Outside
Diff.
Temperature
Set Point
SETTINGS
1
Adjusting the Opening and Closing Temperatures
The opening and closing temperatures are the temperature values at which
the curtains open or close. The hysteresis is fixed at 0.3oF and determines
when the curtains stop operating. When these values are adjusted, all the
starting values for consecutive stages are adjusted by the same amount. The
closing temperature is bounded below by the temperature at which Stage 2
fans turn off. The difference between the opening and closing temperatures
can go from 0.5°F to 20.0°F (0.3°C to 11.1°C).
44 QM 1312.rev.05
Adjusting the Curtain Timer
n
Set the selection knob to CURTAINS - OPEN/CLOSE TEMP./TIMER.
The current curtain time on flashes on the display, alternating with the
word On.
n
Use the adjustment knob to set the time on to the desired value.
n
Press the push-button. The current time off flashes, alternating with
the word Off.
n
Use the adjustment knob to set the time off to the desired value.
The time on and time off parameters can take values from 0 to 900 seconds.
QM 1312.rev.05
45
SS 5124
3
Adjusting the Low Outside Temperature Limit
This value is used to ensure that the natural ventilation mode does not start
(i.e. the curtains are not opened) when the outside temperature is too low. If
the outside temperature is below the low temperature limit, the curtains do
not open. Limit values range from -40oF to 99.9 oF (-40oC to 37.7oC).
n
Set the selection knob to OUTSIDE TEMP. / SETTINGS. The current
outside temperature is displayed.
n
Press the push-button. The current lower limit is displayed, alternating with the letters LO.
n
HEATER SETTINGS
STAGED HEATERS
To configure your system for staged heaters, set dipswitch # 5 to OFF. All
heaters operate according to the average reading from all temperature probes
and only one heater off temperature is needed.
Heating
Heater B OFF
Heater B ON
Heater B
Heater A ON
Heater A
Heater A OFF
Use the adjustment knob to set the lower limit to the desired value.
4
Adjusting the Outside Temperature Differential
This value is used when outside temperature compensation is activated.
The outside differential can go from 0.5°F to 20.0°F (0.3°C to 11.1°C).
n
Set the selection knob to OUTSIDE TEMP. / SETTINGS. The current outside temperature is displayed.
n
Press the push-button twice. The current differential is displayed,
alternating with the letters "dif".
n
Use the adjustment knob to set the differential to the desired value.
HEATER B
START
TEMP.
= 70oF
HEATER A
START
TEMP.
= 72oF
OFF
TEMP.
= 74oF
Set Point
= 75oF
Room
Temperature
If the room temperature rises:
- at 72oF: Heater B turns off.
- at 74oF: Heater A turns off.
If the room temperature falls:
- at 72oF: Heater A turns on.
- at 70oF: Heater B turns on.
46 QM 1312.rev.05
QM 1312.rev.05
47
SS 5124
SS 5124
1
Adjusting Starting Temperatures for Staged Heaters
The heater starting temperature is the temperature at which the heating
units turn on (see diagram above). The Heater A starting temperature is
bounded above by the off temperature — 0.5°F and below by the off temperature — 20oF. The Heater B starting temperature is bounded above by
the Heater A starting temperature — 0.5°F and below by the Heater A
starting temperature — 20oF.
n
n
Set selection knob to HEATER
A — START TEMP. The current starting temperature for
Heater A is displayed, alternating with the letters "Ht.A".
Use the adjustment knob to adjust the starting temperature to
the desired value.
n
Set selection knob to HEATER B — START TEMP. The current
starting temperature for Heater B is displayed, alternating with the
letters "Ht.b".
n
Use the adjustment knob to adjust the starting temperature to the
desired value.
2
ZONED HEATERS
To configure your system for zoned heaters, set dipswitch # 5 to ON. Since
the two heater outputs function independently, different probes are assigned
to each output: Probes 1 & 2 are assigned to Heater A and Probes 3 & 4 are
assigned to Heater B. Individual probes can be turned on or off using the
push-button functions contained in the ROOM TEMPERATURE function (see
section on Temperature Settings).
Note that the heaters can become active only if the average temperature
from all activated probes is below the set point. If this isn't the case, the
heaters will not turn on even if individual probe temperatures are below the
set point (this condition applies only if both off temperatures are below the
set point).
The figure below explains the operation of zoned heaters.
Heating
Heater turns on
ON
Heater turns off
Adjusting Off Temperatures for Staged Heaters
The heater off temperature can provide substantial energy savings if correctly adjusted according to the outside temperature. It is the temperature
below the set point at which the heating units turn off (see diagram above).
The off temperature is bounded above by the set point + 10°F and below by
the set point — 20oF.
n
Set selection knob to HEATER A/B — OFF TEMP. The current off
temperature is displayed, alternating with the letters "Ht.A".
n
Use the adjustment knob to adjust the off temperature to the desired
value.
48 QM 1312.rev.05
OFF
Heater Diff.
= 1oF
OFF
TEMP.
= 74oF
Temperature
Set Point
= 75oF
Heater A - Probes 1 & 2
Heater B - Probes 3 & 4
QM 1312.rev.05
49
SS 5124
SS 5124
If the room temperature rises:
- at 74oF: Heater A (Probes 1 & 2) turns off. Heater B (Probes 3 &
4) turns off.
If the room temperature falls:
- at 73oF: Heater A (Probes 1 & 2) turns on. Heater B (Probes 3 &
4) turns on.
1
2
The starting temperature is the temperature at which the heater turns on.
The Heater A starting temperature is bounded above by the off temperature — 0.5oF and below by the off temperature — 20oF. The Heater B
starting temperature is bounded above by the Heater A starting temperature — 0.5oF and below by the Heater A starting temperature — 20oF.
n
Set the selection knob to HEATER A — START TEMP. The current
starting temperature for Heater A is displayed, alternating with the
letters "Ht.A".
n
Use the adjustment knob to adjust the starting temperature to the
desired value.
n
Set the selection knob to HEATER B — START TEMP. The current
starting temperature for Heater B is displayed, alternating with the
letters "Ht.B".
n
Use the adjustment knob to adjust the starting temperature to the
desired value.
Adjusting Off Temperatures for Zoned Heaters
The heater off temperature can provide substantial energy savings if correctly adjusted according to the outside temperature. It is the temperature
below the set point at which the heating units turn off (see diagram above).
The off temperature is bounded above by the set point + 10oF (5.6oC) and
below by the set point — 20oF (11.1oC).
n
Set selection knob to HEATER
A/B — OFF TEMP. The current off temperature for Heater
A is displayed, alternating with
the letters "Ht.A".
n
Use the adjustment knob to adjust the off temperature to the
desired value.
n
Press the push-button. The current off temperature for Heater B is
displayed, alternating with the letters "Ht.b".
n
Use the adjustment knob to adjust the off temperature to the desired
value.
50 QM 1312.rev.05
Adjusting the Heater Starting Temperatures
QM 1312.rev.05
51
ALARM SETTINGS
TEST MODE
A test mode allows you to simulate temperature changes and verify controller performance. In test mode, the temperature probe inputs are turned off,
allowing the user to change the temperature used by the controller to operate the stages. The controller operates as before using the new temperature settings.
To enter test mode:
n
Turn the selector knob to the ROOM TEMPERATURE position. The
current room temperature is displayed.
n
Press and hold the push-button for 5 seconds. The letters "TST" are
displayed, alternating with the room temperature.
n
Turn the adjustment knob to adjust the room temperature to the desired value. The controller operates the stages according to the new
temperature setting.
n
To change the outside temperature, turn the selector knob to OUTSIDE T° and turn the adjustment knob to adjust the outside temperature to the desired value.
To exit test mode:
n
Turn the selector knob to the ROOM TEMPERATURE position. The
current room temperature is displayed.
n
Press and hold the push-button for 5 seconds.
NOTE: If no user activity is recorded after 5 minutes in test mode, the
controller resumes normal operation.
The controller sets off an alarm in the case of a power failure, a fault in the
supply circuit or a high or low temperature. Temperature alarms are defined according to the set point as shown in the diagram below.
Room
Temperature
High Alarm Offset
Set Point
Low Alarm Offset
Time
The situation changes for high temperature alarms, however, when the outside
temperature is greater than the set point. In this case, the set point is
replaced by the outside temperature as the reference point. This means an
alarm is set off when the indoor temperature reaches Outside Temperature
+ High Alarm Offset. A third parameter, called the critical high temperature,
is defined to continue monitoring the indoor temperature for high
temperatures. When the indoor temperature reaches the critical high
temperature (defined as an absolute value), an alarm is set off. Note that if
internal switch # 7 is OFF, the outside temperature is not used as a reference
point.
Adjusting the Alarm Settings
The high and low alarm offsets range from 0.5oF to 40oF. The critical
temperature ranges from -40.0°F to 120.0°F (-40.0°C to 48.9°C).
n
52 QM 1312.rev.05
High Temperature Alarm
Set the selection knob to
ALARM — LO/HIGH. The current low alarm offset flashes on
the display, alternating with the
word "LO" and "OFT".
QM 1312.rev.05
53
SS 5124
n
Use the adjustment knob to set the low alarm offset to the desired
value.
n
Press the push-button. The current high alarm offset flashes on the
display, alternating with the word "HI" and "OFT".
n
n
n
TROUBLESHOOTING GUIDE
CAUSE
SOLUTION
The circuit breaker
at the service panel
is off or tripped.
Correct the problem and reset
the circuit breaker.
The wiring is
incorrect.
Correct the wiring.
The voltage selector
switch is in the
wrong position.
Set the switch to the correct
position.
The display board
interconnect cable
is not properly
plugged into the
power supply
board.
Be sure the cable is firmly
plugged in.
The display
shows "P"
when the
parameter
selection knob
is set to OUTSIDE SETTINGS.
The outside probe
is connected
improperly.
Correct the outside probe
connection.
The outside probe
is defective.
Refer to "defective probes"
The display
shows "P"
when the
parameter
selection knob
is set to ROOM.
A room probe is
connected improperly.
Correct the room probe
connection.
A room probe is
defective.
Refer to "defective probes"
PROBLEM
There is no
display.
Use the adjustment knob to set the high alarm offset to the desired
value.
Press the push-button. The current critical high temperature is displayed, alternating with the letters "ABS".
Use the adjustment knob to set the critical high temperature to the
desired value.
54 QM 1312.rev.05
QM 1312.rev.05
55
SS 5124
SS 5124
PROBLEM
CAUSE
SOLUTION
The defective
probe pilot light
is on.
A room or outside
probe is defective.
Refer to "defective probes"
The display
shows sudden
variations in the
room or outside
temperature.
A variation in
resistance is
induced on a
probe.
Be sure the probes are dry.
Locate them away from drafts
and sources of radiant heating.
Be sure the outside probe is
installed correctly. Refer to
"Installing the outside probe"
There is electrical
noise near a probe
cable.
The stage 1
variable speed
cooling fans are
not running.
56 QM 1312.rev.05
Isolate the probe cables from
all high voltage sources. Do
not route probe cables and
other power cables through
the same electrical knockout.
Do not run probe cables next
to other power cables. When
crossing other power cables,
cross at 90°.
The wiring is
incorrect.
Correct the wiring. Be sure two
different lines are connected to
each fan motor: line L1
modulated by the controller
should be combined with
another line (N for 115V or L2
for 230V) to activate the motor.
Also, be sure the stage 1
COMMON is supplied by line L1.
The stage 1 fuse is
open.
Correct the problem and
replace the fuse.
The display board
interconnect cable is
not properly plugged
into the power supply
board.
Be sure the cable is firmly
plugged in.
PROBLEM
The stage 1
variable speed
cooling fans are
not running.
(continued)
The stage 1
variable speed
cooling fans run
erratically.
CAUSE
SOLUTION
The minimum
speed is too low.
Adjust the minimum speed to
a higher value.
The fan motor is
defective.
Check if the motor is defective
by connecting it to an alternate
power supply. If it still is not
operating, replace the motor.
The selected motor
curve is inappropriate.
Select an appropriate motor
curve. Refer to "motor curves"
The stage 1 differential is too small.
Adjust the stage 1 differential
to a higher value.
The stage 1 time on
or time off is too
short.
Adjust the stage 1 time on or
time off to a higher value.
A variation in
resistance induced
on a room probe
causes this probe
to measure sudden
variations in the
room temperature.
Be sure the room probes are
dry. Locate them away from
drafts and sources of radiant
heating.
Electrical noise
near a room probe
cable causes this
probe to measure
sudden variations in
the room temperature.
Isolate the room probe cables
from all high voltage sources.
Do not route probe cables and
other power cables through
the same electrical knockout.
Do not run probe cables next
to other power cables. When
crossing other power cables,
cross at 90°.
QM 1312.rev.05
57
SS 5124
SS 5124
PROBLEM
CAUSE
The stage 1
variable speed
cooling fans run
continuously
when the room
temperature is
below the room
set point
(minimum
ventilation
cycle).
The stage 1 time off
is set to zero.
Set the stage 1 time off to
a value other than zero.
The wiring is
incorrect.
Correct the wiring. Be sure
two different lines are connected to each fan motor: line
L1 modulated by the controller
should be combined with
another line (N for 115V or L2
for 230V) to activate the motor.
Also, be sure the
stage 1 COMMON is supplied
by line L1.
SOLUTION
The mist is not
operating as
desired.
The mist time on
and time off were
incorrectly adjusted.
The mist time on and time off
are in minutes. Adjust the mist
time on and time off correctly.
The cooling
fans are not
running.
The wiring is
incorrect.
Correct the wiring. Be sure
two different lines are connected to each fan motor or
heater: the controller's output
line L1 should be combined
with another line
(N for 115V or L2 for 230V) to
activate the fan motor or
heater. Also, be sure the
stage's COMMON is supplied
by line L1.
The stage's fuse is
open.
Replace the fuse.
or
The heaters are
not turning on.
58 QM 1312.rev.05
PROBLEM
The cooling
fans are not
running.
or
The heaters are
not turning on.
CAUSE
The display board
interconnect cable
is not properly
plugged into the
power supply
board.
Be sure the cable is firmly
plugged in.
The fan motor or
heater is defective.
Check if the motor or heater is
defective by connecting it to an
alternate power supply. If it still
is not operating, replace the
motor or heater.
The controller is
defective.
Listen to see if there is a
clicking sound when the stage
or heater pilot light turns on. If
there is no clicking sound,
contact your distributor to
repair the controller.
The fuse on the
curtain output is
blown.
Replace the fuse.
(continued)
The curtains do
not work.
SOLUTION
QM 1312.rev.05
59
TECHNICAL SPECIFICATIONS
Supply: - 115/230 VAC (-18%, +8%), 60 Hz, L1 same phases as Stage 1,
overload and overvoltage protection fuse F11-1A fast blow.
- 12 VDC for AC back-up supply; can activate stages 2 through 7
if supplied with DC back-up voltage.
FACTORY SETTINGS
PA R A ME T E R
Te m p e r a t u r e S e t P o i n t
Stage 2: ON-OFF output, 115/230 VAC, 60 Hz, 30VDC, 6A FAN,10A RES,
fuse F2-15A slow blow.
Curtains: OPEN-CLOSE output, 115/230 VAC, 60 Hz, 30VDC, 5A winch
output, fuse F1-5A fast blow.
Stage 4: ON-OFF output, 115/230 VAC, 60 Hz, 30VDC, 6A FAN,10A RES,
fuse F3-15A slow blow.
Stage 5: ON-OFF output, 115/230 VAC, 60 Hz, 30VDC, 6A FAN,10A RES,
fuse F4-15A slow blow.
Stage 6: ON-OFF output, 115/230 VAC, 60 Hz, 30VDC, 6A FAN,10A RES,
heating, fuse F4-15A slow blow.
Stage 7: ON-OFF output, 115/230 VAC, 60 Hz, 30VDC, 6A FAN,10A RES,
heating, fuse F4-15A slow blow.
Alarm: ON-OFF output, 115/230 VAC, 60 Hz, 30VDC, 3A, fuse F8-3A slow
blow.
Probes: Low voltage ( < 5V), isolated from the supply. Operating range:
-40.0° to 120.0°F (-40.0° to 48.9°C). Accuracy: 1.8oF (1oC) between 41o
and 95oF (5o and 35oC).
-40 to 99.9
(-40 to 37.7
o
o
F
C)
0 . 5 t o 2 0 oF
( 0 . 3 t o 1 1 . 1 oC )
40 %
10 % to 100 %
Ti me On
15 seconds
Ti me Off
0 seconds
0 to 900 seconds by
increments of 15
seconds
Bandwidth
3 . 0 oF
( 1 . 7 oC )
0 . 5 t o 2 0 oF
( 0 . 3 t o 1 1 . 1 oC )
Hysteresis
0 . 3 oF
( 0 . 2 oC )
Minimum Speed
Stage 1
7 5 oF ( 2 3 . 9 oC )
R A N GE OF
VA L U E S
2 oF ( 1 . 1 oC )
Outside Differential
Stage 1: Variable output, 60 Hz, 10A FAN (3/4 HP/115 VAC) / (1.5 HP/
230VAC), fuse F1-15A slow blow.
FA C T ORY
S E T T IN G
0.3 to 2.0
(0.2 to 1.1
o
o
F
C)
8 0 oF
( 2 6 . 7 oC )
Set Point + Bandwidth
to Set Point +
B a n d w i d t h + 2 0 oF
( 1 1 . 1 oC )
O p e n i n g Te m p .
8 2 oF
( 2 7 . 9 oC )
Stage 2 Starting
Te m p . + 0 . 5 ° F t o S t a g e
2 Starting
Te m p . + 2 0 oF ( 1 1 . 1 oC )
C u r t a i n s C l o s i n g Te m p .
8 0 oF
( 2 6 . 7 oC )
0 . 5 t o 2 0 oF
( 0 . 3 t o 1 1 . 1 oC ) f r o m
O p e n i n g Te m p .
Stage 2 - Starting
Te m p .
Ti me On
15 seconds
Ti me Off
15 seconds
L o w O u t s i d e Te m p . L i m i t
5 0 oF ( 1 0 oC )
0 to 900 seconds by
increments of 1 second
-40 to 99.9
(-40 to 37.7
o
o
F
C)
Enclosure: ABS, moisture and dust-tight.
The room temperature where the controller is located MUST
ALWAYS REMAIN BETWEEN 32o AND 104oF (0o AND 40oC).
60 QM 1312.rev.05
QM 1312.rev.05
61
SS 5124
F A C T O R Y
S E T T I N G
R A N G E O F
V A L U E S
S t a g e 4 - S t a r t i n g Te m p .
8 4 oF
( 2 8 . 9 oC )
C u r t a i n O p e n i n g Te m p .
+ 0 . 5 oF ( 0 . 3 oC ) t o
C urtai n Openi ng
Te m p . + 2 0 oF ( 1 1 . 1 oC )
S t a g e 5 - S t a r t i n g Te m p .
8 6 oF
( 3 0 oC )
Stage 4 St
+ 0 . 5 oF ( 0 . 3
4 Starti ng
(11
S t a g e 6 - S t a r t i n g Te m p .
8 8 oF
( 3 1 . 1 oC )
Stage 5 St
+ 0 . 5 oF ( 0 . 3
5 Starti ng
(11
S t a g e 7 - S t a r t i n g Te m p .
9 0 oF
( 3 2 . 2 oC )
Stage 6 St
+ 0 . 5 oF ( 0 . 3
6 Starti ng
(11
P A R A M E T E R
Ti me On
1 mi nute
Ti me Off
0 mi nutes
Mi st
a r t i n g Te m p .
C ) to Stage
Te m p . + 2 0 oF
. 1 oC )
o
a r t i n g Te m p .
C ) to Stage
Te m p . + 2 0 oF
. 1 oC )
o
a r t i n g Te m p .
C ) to Stage
Te m p . + 2 0 oF
. 1 oC )
o
0 to 60 mi nutes
Heater A -Starti ng
Te m p .
7 2 . 5 oF
( 2 2 . 5 oC )
O f f Te m p . - 0 . 5 oF ( 0 . 3 oC )
t o O f f Te m p . - 2 0 oF
( 1 1 . 1 oC )
Heater B -Starti ng
Te m p .
7 0 . 5 oF
( 2 1 . 4 oC )
Hea
Te m p .
Hea
Te m p
H e a t e r A / B O f f Te m p .
7 4 . 5 oF
( 2 3 . 6 oC )
S e t P o i n t - 2 0 oF ( 1 1 . 1 oC )
t o S e t P o i n t + 1 0 oF
( 5 . 6 oC )
Alarm
L o w Te m p .
6 5 oF ( 1 8 . 3 oC )
H i g h Te m p .
8 7 oF ( 3 0 . 6 oC )
C r i t i c a l Te m p .
9 5 oF ( 3 5 oC )
ter A Starti ng
- 0 . 5 oF ( 0 . 3 oC ) t o
ter A Starti ng
. - 2 0 oF ( 1 1 . 1 oC )
0 . 5 t o 4 0 oF
( 0 . 3 t o 2 2 . 2 oC ) f r o m
Set Poi nt
- 4 0 . 0 oF t o 1 2 0 . 0 oF
( - 4 0 oC t o 4 8 . 9 oC )
NOTES:
i) These initial parameter settings will not be retained in the controller's
memory. Each new setting will replace the preceding one.
ii) If the power supply is cut off, the last parameter settings will be
retained in memory until the power is restored.
62 QM 1312.rev.05
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement