User Manual & Datasheet
GAMMA 2.0
Thank you for choosing our product!
This manual offers important information and suggestions about the installation, use
and troubleshooting, etc. Please read this manual carefully before using the product
and pay attention to the safety recommendations within.
www.solarpower-mart.com
Harvest the Sun power!
USER MANUAL
GAMMA 2.0
SOLAR CHARGE CONTROLLER
RATINGS (Automatic 12V and 24V)
NOTES: For use with solar panels and battery only
TECHNICAL INFORMATION
Auto 12 / 24 Volt DC
Nominal System Voltage
Maximum PV Input Voltage
Nominal Charge / Discharge Current
12 / 24VDC
50V
3A, 5A or 10A
The controller will recognize the system rated voltage when started up. If the battery
voltage is lower than 18V, it will recognize the system as 12V. If the battery voltage is
greater than 18V, it will recognize the system as 24V.
www.solarpower-mart.com
Harvest the Sun power!
Notes, Cautions and Warnings
This manual contains important safety, installation and operating instructions. The
following symbols are used throughout this manual to indicate potentially dangerous
conditions or mark important safety instructions, please take note of them.
WARNING: Indicates a potentially dangerous condition. Use extreme caution when
performing this task.
CAUTION: Indicates a critical procedure for safe and proper operation of the controller.
Note: Indicates a procedure or function that is important for the safe and proper
operation of the controller.
General Safety Guideline






Read all of the instructions and cautionary symbols in the manual before
beginning installation.
There are no serviceable parts inside the controller. Do not disassemble or
attempt to repair it.
Install external fuses/Mini Circuit Breaker (MCB) as required.
Disconnect the solar panel (module/PV) and fuse/MCB near the battery before
installing or adjusting the controller.
Do not allow water to enter the controller.
Confirm that power connections are tightened to avoid excessive heating from a
loose connection.
www.solarpower-mart.com
Harvest the Sun power!
General Information
Thank you for selecting GAMMA series solar controller that adopts the most advanced
digital techniques and is fully automatic. The Pulse Width Modulation (PWM) battery
charging can greatly increase the lifetime of the battery. It has various unique functions,
such as:
 12/24V automatic recognition.
 Highly efficient Series PWM charging increases the battery life and improves the
solar PV system’
s performance.
 Uses MOSFET as electronic switch.
 Widely used, automatically recognize day/night technology.
 Digital LED display, only one key setting to program all functions.
 Intelligent timer function with 1-15 hours option.
 Unique dual timer function, enhance the flexibility of lighting system.
 Selectable Gel, Sealed and Flooded battery type options.
 Adopts temperature compensation, corrects the charging and discharging
parameters automatically and improves battery life.
 Electronic protection from overheating, over charging, over discharging,
overload, and short circuit.
 Reverse protection: any combination of solar module and battery.
 Support On Grid (grid-tie) solar panel (maximum PV voltage input 50V).
 Imbedded desulfator function from PWM technology.
The controller is for multipurpose off-grid solar systems and enhances solar light
system, protects the battery from being over charged by the solar module and over
discharged by the loads. The charging process has been optimized for long battery life
and improved system performance. The comprehensive self-diagnostics and electronic
protection functions can prevent damage from installation mistakes or system faults..
Although the controller is easy to operate and use, please kindly study this user manual
before you begin. This will help you make full use of the functions and you can improve
your solar system.
www.solarpower-mart.com
Harvest the Sun power!
Product Features
1. Temperature Sensor
Measure ambient temperature and make temperature compensation for charging and
discharging.
2. PV (solar panel) Charging Status LED indicator
A LED indicator that shows charging status and also indicates warning signal when solar array
connect wrongly.
3. Battery Status LED Indicator
A LED indicator that shows battery status and other crucial information.
4. Battery Type Setting Indicator
Select battery type indicator: SEL, GEL and Flood.
5. Timer 2 Setting Indicator
The indicator will be on when set Timer 2.
6. Timer 1 Setting Indicator
The indicator will be on when set Timer 1.
7. LED Digital Display
Display the load program mode and status.
8. Setting Button (in manual mode used for load ON/OFF Switch)
Set load program mode (Timer 1 & Timer 2) and select battery type.
9. Solar Module Terminals
Connect solar modules.
10. Battery Terminals
Connect batteries.
11. Load Terminals
Connect loads.
www.solarpower-mart.com
Harvest the Sun power!
Installation
General Installation Notes:









Read through the entire installation section first before beginning installation.
Be careful when working with batteries. Wear eye protection if necessary. Have
fresh water available to wash and clean any contact with battery acid.
Uses insulated tools and avoid placing metal objects near the batteries.
Explosive battery gasses may be present during charging. Be certain there is
sufficient ventilation to disperse the gasses.
Avoid direct sunlight and do not install in locations where water can enter the
controller.
Loose power connections and/or corroded wires may result in resistive
connections that melt wire insulation, burn surrounding materials, or even cause
fires. Ensure tight connections and use cable clamps to secure cables and
prevent them from swaying from mobile applications.
Use with Gel, Sealed or Flood batteries only.
Battery may be wired to one battery or more batteries. The following instructions
refer to the use of a single battery, but the battery connection can be made to
either one battery or a group of batteries in a battery bank.
Select the system cables accordingly or consult us for more details.
Mounting Requirements
NOTE: When mounting the controller, ensure there is free air flow through the controller
heat sink fins. There should be at least 6 inches (150 mm) of clearance above and
below the controller to allow for cooling. If mounted in an enclosed space, providing
ventilation is highly recommended.
WARNING: Risk of explosion! Never install the controller in a sealed enclosed area
with flood batteries! Do not install in a confined area where battery gass can
accumulate.
www.solarpower-mart.com
Harvest the Sun power!
Step 1: Choose Mounting Location
Place the controller on a vertical surface protected from direct sunlight, high
temperature, and moisture. Provide good ventilation.
Step 2: Check for clearance
Place the controller at the location where it will be mounted. Verify that there is
sufficient room to run the wires and that there is sufficient room above and below the
controller for air flow.
Step 3: Mark Holes
Use a pencil or pen to mark the four (4) mount points on the surface.
Step 4: Drill Holes
Remove the controller and drill 4.5mm holes in the marked locations.
Step 5: Secure Controller
Place the controller on the surface and align the mounting holes with the drilled holes in
step 4. Secure the controller in place using the mounting screws.
www.solarpower-mart.com
Harvest the Sun power!
Wiring
NOTE: A recommended connection order (step by step) has been created to provide
maximum safety during installation.
NOTE: The controller is a common positive ground controller.
CAUTION: Do not connect the loads with surge power exceeding the rating of the
controller.
CAUTION: For mobile applications, be sure to secure all wiring. Use cable clamps to
prevent cables from swaying when the vehicle/object is in motion. Unsecured cables
create loose and resistive connections which may lead to excessive heating and/or fire.
www.solarpower-mart.com
Harvest the Sun power!
Step1: Battery Wiring
WARNING: Risk of explosion or fire! Never connect the positive (+) and negative
(-) battery cables.
Before battery is connected, make sure that the battery voltage is greater than 6V to
start up the controller. If the system is 24V, make sure battery voltage is not less than
18V. During the first start up, the controller will automatically recognize the system
voltage.
When installing a fuse or Mini Circuit Breaker (MCB), make sure that the distance
between the fuse holder and the positive terminal of battery does not exceed 150mm.
Do not insert a fuse (MCB) at this time.
Make sure the battery cable is less than 0.5 meter long to prevent power loss.
Always keeps the controller as close as possible so that it can sense the battery
temperature for effective charging (temperature compensation).
www.solarpower-mart.com
Harvest the Sun power!
Step 2: Load Wiring
The controller can be connected to electrical equipments such as lights, pumps, and
motors. The controller draws power from the battery.
Connect the positive (+) and negative (-) controller load terminals as shown in above
Figure. A fuse holder (MCB) should be wired in series with the load positive (+) or
negative (-) wire as shown in above Figure. Do not insert a fuse (turn off the MCB)
at this time.
When wiring the load connection to a load distribution panel, each load circuit should be
fused separately. The total load draw should not exceed the rated load current of the
controller.
www.solarpower-mart.com
Harvest the Sun power!
Step 3: Solar wiring
WARNING: Risk of electric shock! Be caution when handling solar panel wiring.
The high voltage from solar panel’s can induce electric shock and injury. Keep
the solar panel away from sunlight before installing the solar wiring.
The controller cans accept 12V or 24V nominal off-grid solar panel(s). Grid-tie solar
panel(s) may be used if the open circuit voltage of solar panel doesn’
t exceed the
Maximum PV input voltage (50V) of the controller.
If using Grid-tie (On-Grid) solar panel, the battery system must be 24V.
The solar panel(s) work voltage must be equal to or greater than the system voltage.
For a good set up, please kindly use solar connector like the MC4 solar connector.
Do not connect the solar connector (MC4) immediately.
A MCB can be installed in between solar panel and the controller as a fuse or circuit
breaker.
www.solarpower-mart.com
Harvest the Sun power!
Step 4: Confirm Wiring
Double-check the system wiring from step 1 through 3. Confirm correct polarity at each
connection. Make sure all six terminals are tightened.
Step 5: Install Fuse/Turn on MCB
Install a suitable fuse in each fuse holder in the following order:
1. Battery circuit
2. Load circuit
3. Connect the solar panel connector (MC4).
Step 6: Power up the controller
When the controller starts up, the battery LED indicator will be green. If the controller
doesn't start up, or the status LED error is active, please refer to Troubleshooting
Section.
www.solarpower-mart.com
Harvest the Sun power!
ADVANCE CHARGING TECHNOLOGY
PWM Technology (Series Pulse Width Modulation)
The controller adopts Advanced Series Pulse Width Modulation (PWM) technology.
PWM is the most effective means to achieve constant voltage battery charging by
switching the solar system controller’
s power devices. When in PWM regulation, the
current from the solar array tapers according to the battery’
s condition and recharging
needs.
The operating principle of PWM charging mode is as follows:
PWM solar charge controller use technology similar to other modern high quality battery
chargers.
When a battery voltage reaches the regulation set point, the PWM algorithm slowly
reduces the charging current to avoid heating and gassing of the battery, yet the
charging continues to return the maximum amount of energy to the battery in the
shortest time. The result is a higher charging efficiency, rapid recharging, and a healthy
battery at full capacity.
In addition, this new method of solar battery charging promises some very interesting
and unique benefits from the PWM pulsing. These include:
1) Ability to recover lost battery capacity and desulfate a battery.
2) Dramatically increase the charge acceptance of the battery.
3) Maintain high average battery capacities (90% to 95%) compared to on-off
regulated state of charge levels that are typically 55% to 60%.
4) Equalize drifting battery cells.
5) Reduce battery heating and gassing.
6) Automatically adjust for battery aging.
7) Self-regulate for voltage drops and temperature effects in solar systems.
www.solarpower-mart.com
Harvest the Sun power!
Battery Charge Information
Figure: PWM charging mode
Bulk Charge In this stage, the battery voltage has not yet reached the boost voltage
and 100% of available solar power is used to charge the battery.
Boost Charge/ PWM Regulation
When the battery has been charged to boost voltage point, constant-voltage regulation
is used to prevent over-heating and excessive battery gas releases. The boost stage
remains for 120 minutes and then reduces into a float charge. This is where the PWM
technology applies.
Float Charge
After the battery is fully charged in boost voltage stage, the controller reduces the
battery voltage to float voltage set point. When the battery is fully charged, there will be
no more chemical reactions and all the charge current transmits into heat and gas at
this time. Then the controller reduces the voltage to the floating stage, charging with a
smaller voltage and current. It will reduce the temperature of battery and prevent gas
release, and also charges the battery with a low current.
The purpose of float stage is to offset the power consumption caused by self
consumption and small loads in the whole system, while maintaining full battery storage
www.solarpower-mart.com
Harvest the Sun power!
capacity. In float stage, loads can continue to draw power from the battery. In the
event that the system load(s) exceed the solar charge current, the controller will no
longer be able to maintain the battery at the float set point. Should the battery voltage
remains below the boost set point, the controller will exit float stage and return to bulk
charge.
Equalize Charge
WARNING: Risk of explosion!
Equalizing flood batteries can produce explosive gases, so well ventilated battery boxes
are necessary.
NOTE: Equipment damage!
Equalization may increase battery voltage and can cause damaged to sensitive DC
loads. Ensure that all loads allow input voltages that are greater than the equalizing
charging set point voltage.
NOTE: Equipment damage!
Over-charging and excessive gas precipitation may damaged the battery plates and
activate material shedding on them. Too high or too long an equalizing charge may
cause damage. Please carefully review the specific requirements of the battery used in
the system.
Certain types of batteries benefit from periodic equalizing charges, which can stir up the
electrolyte, balance the battery voltage and complete certain chemical reactions.
Equalizing charges increase battery voltage; higher than the standard complement
voltage, which gasifies the battery’
s electrolyte.
If the battery is over discharged, the solar controller will automatically switch into the
equalizing charge stage, and it remains as such for 120mins. The Equalizing charge
www.solarpower-mart.com
Harvest the Sun power!
and boost charge are not carried out constantly in a full charge process so as to avoid
too much gas precipitation or heat generation in the battery.
LED INDICATION
Charging Status indicator
GREEN ON whenever sunlight is available for battery charging,
GREEN FAST FLASHING when system is over voltage.
Please refer to Troubleshooting Section for more detail.
Charging Status LED Indicator
Color
Indicator
Charging Status
Green
On Solid
Charging
Green
Fast Flashing
Overvoltage
Battery Status indicator
GREEN ON when battery voltage in normal range
GREEN SLOWLY FLASHING when battery full
ORANGE ON when battery under voltage
RED ON when battery is over discharged.
Please refer to Troubleshooting Section for more details.
www.solarpower-mart.com
Harvest the Sun power!
Battery Status LED Indicator
Color
Indicator
Battery Status
Green
On Solid
Normal
Green
Slowly Flashing
Full
Orange
On Sold
Under voltage
Red
On Sold
Over discharged
Load Status Indicator:
When the load current is 1.25 times of rated current for 60 seconds, or the load current
is 1.5 times of rated current for 5 seconds (overload); or load current is more than 3.5
times of rated current (Short Circuit) ,the LED digital display will show “L”and flash
slowly.
Please refer to Troubleshooting Section for more details.
Load Status LED Indicator
Color
LED Digital Display
Load Status
Red
Overload or short circuit
“L”with slowly flashing
Overheating Protection Indicator:
When heat sink of the controller exceeds 85°C, the controller will automatically cut the
input and output circuit, with LED digital display showing “H”with flash slowly.
Please refer Troubleshooting Section for more details.
Overheating Protection Indicator
Color
LED Digital Display
Load Status
Red
Controller overheating
www.solarpower-mart.com
“H”with slowly flashing
Harvest the Sun power!
TIMER SETTING FUNCTION
Dual Timer Function
The default night length setting is 10 hours. The controller can learn the night period by
referring the night before. It also can adapt to the different seasons (day light saving).
However, it may require time to adjust and learn.
Notes: When Timer 2 is disabling, the controller will turn off the load output at the
sunrise time.
Load Controller Settings
1. Dusk to Dawn
When solar module voltage goes below the point of Night Time Threshold Voltage
(NTTV) at dusk/sunset, the controller will recognize the starting voltage and turn on the
load after 10 minutes.
When solar module voltage goes above point of Day Time Threshold Voltage (DTTV),
the solar controller will recognize the starting voltage and turn off the load after 10
minutes.
2. Light ON + Timer
When solar module voltage goes below the point of NTTV (Night Time Threshold
Voltage) at sunset; the solar controller will recognize the starting voltage and turn on the
load after 10 minutes delay. The load will be on for several hours which users set
through LED digital display. The controller has dual timer function. Please refer to table
“Load Programming Mode Settings”.
www.solarpower-mart.com
Harvest the Sun power!
3. Test Mode
This mode is similar to Dusk to Dawn setting, but there is no 10 minutes delay when
controller recognizes the starting voltage. When below the starting voltage, the
controller will turn on the load, if higher, it will turn off load. The test mode makes it
easy to check the solar lighting system during installation.
4. ON/OFF Mode (Manual Switcher)
This mode is to turn ON and OFF the load by manual setting.
Load Program Mode Setting
Setting Operation Indicator
Press the setting button once and setting indicators will change once among Timer 1,
Timer 2 and battery type.
When Timer 1 setting indicator is on, press the setting button for 5 seconds till the LED
digital display flashes. Then press the setting button till the desired number appears
according to the following table. The setting is finished when the digital display stops
flashing.
Timer 2 setting is the same as Timer 1 when the setting indicator is on Timer 2.
www.solarpower-mart.com
Harvest the Sun power!
Load Programming Mode for Timer 1
Timer 1
LED Digital No.
Disable
n
Dusk to Dawn, load will be on all night
0
Load will be on for 1 hour (with 10 minutes delay) after dusk.
1
Load will be on for 2 hours (with 10 minutes delay) after dusk.
2
Load will be on for 3 hours (with 10 minutes delay) after dusk.
3
Load will be on for 4 hours (with 10 minutes delay) after dusk.
4
Load will be on for 5 hours (with 10 minutes delay) after dusk.
5
Load will be on for 6 hours (with 10 minutes delay) after dusk.
6
Load will be on for 7 hours (with 10 minutes delay) after dusk.
7
Load will be on for 8 hours (with 10 minutes delay) after dusk.
8
Load will be on for 9 hours (with 10 minutes delay) after dusk.
9
Load will be on for 10 hours (with 10 minutes delay) after dusk.
10
Load will be on for 11 hours (with 10 minutes delay) after dusk.
11
Load will be on for 12 hours (with 10 minutes delay) after dusk.
12
Load will be on for 13 hours (with 10 minutes delay) after dusk.
13
Load will be on for 14 hours (with 10 minutes delay) after dusk.
14
Load will be on for 15 hours (with 10 minutes delay) after dusk.
15
Test Mode
16
On/Off Mode
Manual Switcher
17
www.solarpower-mart.com
Harvest the Sun power!
Load Programming Mode for Timer 2
Timer 2
LED Digital No.
Disable
n
Load will be on for 1 hour before dawn.
1
Load will be on for 2 hours before dawn.
2
Load will be on for 3 hours before dawn.
3
Load will be on for 4 hours before dawn.
4
Load will be on for 5 hours before dawn.
5
Load will be on for 6 hours before dawn.
6
Load will be on for 7 hours before dawn.
7
Load will be on for 8 hours before dawn.
8
Load will be on for 9 hours before dawn
9
Load will be on for 10 hours before dawn.
10
Load will be on for 11 hours before dawn.
11
Load will be on for 12 hours before dawn.
12
Load will be on for 13 hours before dawn.
13
Load will be on for 14 hours before dawn.
14
Load will be on for 15 hours before dawn.
15
Notes: If Timer 1 is Dusk to Dawn (0), Test Mode (16) or ON/OFF Mode (17), the Timer
2 will be disabled.
When the battery typesetting indicator is on, press the setting button for 5 seconds till
the LED digital display flashes. Then press the setting button till the desired number
appears according to the following table. The setting is finished till the LED digital
display stops flashing.
www.solarpower-mart.com
Harvest the Sun power!
Battery Type Setting
Battery Type
Digital LED Display
Sealed Lead Acid Battery/AGM
1
Gel Battery
2
Flooded Battery
3
www.solarpower-mart.com
Harvest the Sun power!
TROUBLESHOOTING
Protection
PV Array Short Circuit
If PV array short circuit occurs, clear it to resume normal operation.
Load Overload
If the load current exceeds the maximum load current rating, the controller will
disconnect the load. The greater the overload, the faster the load will be disconnected.
A small overload could take a few minutes to disconnect. Overloading must be cleared
up through reapply power or pressing the setting button.
Load Short Circuit
Fully protected against load wiring short-circuit. After one automatic load reconnect
attempt, the faulty error must be cleared by reapply power or pressing the setting
button.
PV Reverse Polarity
The controller fully protects against PV reverse polarity, therefore no damage to the
controller. Please check and re-correct the wire to resume operation.
Battery Reverse Polarity
The controller fully protects against battery reverse polarity, therefore no damage to the
controller. Please check and re-correct the wire to resume operation.
Damaged Local Temperature Sensor
If the temperature sensor short-circuited or damaged, the controller will be charging or
discharging at the default temperature of 25°C to prevent the battery damaged from
overcharging or over discharged.
Overheating Protection
If the controller’
s internal temperature exceeds 85°C, the controller will automatically
start the overheating protection.
High Voltage Transients
Battery is protected against high voltage transients. In lightning prone areas, a lighting
arrestor is highly recommended.
www.solarpower-mart.com
Harvest the Sun power!
Problem
Possible Causes
Possible Solutions
PV Charging Status LED indicator
light off during daytime (when sunlight
presence).
PV array may be
disconnected
Check PV and battery wire
connections.
PV Charging Status LED indicator
turned green with fast flashing
Battery voltage higher
than Over Voltage
Disconnect voltage(OVD)
Check if battery voltage.
Disconnect the solar module
Battery Status LED Indicator turned
orange
Battery under voltage
Load output is normal,
charging LED indicator will
return to green when battery
fully charged by PV.
Battery Status LED Indicator turned
red and loads turned off.
Battery over discharged
The controller cut off the load
output to prevent over
discharge, LED indicator will
return to green when battery
fully charged.
LED Digital Displays shown “L”with
red slowly flashing
Overload or short circuit
occurred
Overload: Please reduce the
load and press the setting
button once, the controller will
resume to normal operation
after 3s;
Short circuit: when the first
short-circuit occurs, the
controller will automatically
resume to normal operation
after 10s;
When a second short-circuit
occurs, press the button, the
controller will resume to
normal operation after 3s.
LED Digital Displays shown “H”with
red slowly flashing
Controller temperature is
too high.
When heat sink of the
controller exceeds 85℃ , the
controller will cut off power
input and output. When the
temperature below 75℃ , the
controller will resume to
normal operation.
Notes: No Battery Status LED Indicator - Please measure battery voltage with a
multimeter. The minimum requirement is 6V to start up the controller.
Notes: No PV Charging Status LED indicator (when sunlight presence) - Please
measure the solar panel input voltage and the input voltage must higher than the battery
voltage (12V or 24V).
www.solarpower-mart.com
Harvest the Sun power!
MAINTENANCE
The following inspections and maintenance tasks are recommended at least twice per
year for best controller performance.
Notes: Danger of electrocution!
Make sure that all power source of controller is cut off when operate above processes,
and then make inspection or other operations!
 Check the controller is securely mounted in a clean and dry environment.
 Check the air flow and ventilation around the controller is not blocked. Clear dirt or
fragments on the heat sink.
 Check all wires to make sure insulation is not damaged for serious solarization,
frictional wear, dryness, insects or rats etc. Maintain or replace the wires if necessary.
 Tighten all the terminals. Inspect for loose, broken, or burnt wire connections.
 Check and confirm that LED digital display is consistent with setting requirement.
Pay attention to any error indication and take necessary action.
 Confirm all system components are ground connected tightly and correctly.
 Confirm all the terminals have no corrosion, insulation damaged, high temperature or
burnt/discolored sign, tighten terminal screws to the suggested torque.
 Inspect for dirt, insects and corrosion, and clear up such obstructions.
 Check and confirm lightning arrester is in good condition. Replace a new one in time
to avoid damaging of the controller and other equipments.
www.solarpower-mart.com
Harvest the Sun power!
LIMITED PRODUCT WARRANTY
SC Origin (M) Sdn Bhd (SCO) warrant to the original purchaser that the GAMMA charge
controller is free from manufacturer defects in material, assembly, and workmanship
under normal use for a period of ONE (1) year from the date of original purchase
subject to the terms and conditions of this Limited Product Warranty (“Limited
Warranty”). By using GAMMA charge controller, you as the original purchaser are
asked to carefully read and agree to the following terms and conditions of this Limited
Warranty before you use the product. Your use of this product constitutes agreement
with all provisions of this warranty. Purchasing this controller from a third party vendor
negates all warranties (expressed or implied) in this warranty.
If any defects due to manufacturing should arise during the first year of purchase and all
terms and conditions of the Limited Warranty have been met, SCO will at its option,
either repair or replace the product to the original purchaser without charge. If the
product cannot be repaired within a reasonable time or a reasonable price, SCO may
elect to refund the purchase price instead. No warranty work will be provided without the
purchaser’
s receipt or other proof of the date of original purchase acceptable to SCO.
This shall be SC Origin (M) Sdn Bhd maximum and total liability.
This warranty does not apply under the following conditions:
1. Damage by accident, negligence, abuse or improper use.
2. PV or load current exceeding the ratings of product.
3. Unauthorized product modification or attempted repair.
4. Damaged occurring during shipment.
5. Damage results from acts of nature disaster such as lightning, floods, fire, wind, etc.
6. Irreclaimable mechanical damage.
7. Damages exceeding the total cost of the controller.
8. The finish on any portion of the controller (i.e. surface scratches, weathering,
corrosion, as this is considered normal wear and tear.)
9. Transit damage, initial installation costs, removal costs, or reinstallation costs.
10. Improper maintenance, installation and/or operation of the controller in other than a
normal operating condition or in such a way as to otherwise fail to comply with the
instructions or manuals thereof or otherwise constitute misuse.
SCO do not incur liability for any of the following in any event:
Personal injury;
Direct, indirect, special, incidental, multiple or consequential damages.
www.solarpower-mart.com
Harvest the Sun power!
Claim procedure: Before requesting warranty service, check the User Manual to be
certain that there is a problem with the controller.
Return the defective product to SCO with shipping charges prepaid if problem cannot be
solved.
Provide proof of date and place of purchase. To obtain rapid service under this
warranty, the returned products must include the model, serial number and detailed
reason for the failure, the module type and size, type of batteries and system loads.
This information is critical to a rapid disposition of your warranty claim.
THE LIMITED WARRANTY IS THE ONLY WARRANTY OF SC ORIGIN (M) SDN
BHD. THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, EXCEPT
AS PROVIDED BY LAW, INCLUDING THE IMPLIED WARRANTY OF QUALITY,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND SUCH
IMPLIED WARRANTIES, IF ANY, ARE LIMITED IN DURATION TO THE TERM OF
THE LIMITED WARRANTY.
www.solarpower-mart.com
Harvest the Sun power!
TECHNICAL SPECIFICATION
Electrical Parameter
Description
Parameter
Nominal System Voltage
12 / 24VDC Auto work
Battery Voltage Range
6-36V
Rated Battery Current
GAMMA-3A
GAMMA-5A
GAMMA-10A
Charge Circuit Voltage Drop
≤0.26V
Discharge Circuit Voltage Drop
≤0.15V
Self-consumption
≤6mA
Threshold Voltage Parameter
Description
3A
5A
10A
Parameter
NTTV (Night Time Threshold Voltage)
5V for 12V system; 10V for 24V system
DTTV (Day Time Threshold Voltage)
6V for 12V system; 12V for 24V system
Temperature Compensation Coefficient
Description
Temperature Compensation
Coefficient(TEMPCO)*
Parameter
-30mV/℃ /12V(25 ref)
Compensation of equalize, boost, float and boost
reconnect voltage
Environmental Parameter
Description
Parameter
Working temperature
-35°C to +55°C
Storage temperature
-35°C to +80°C
Humidity
10%-90% NC
Enclosure
IP30
www.solarpower-mart.com
Harvest the Sun power!
Battery Voltage Parameter (Temperature at 25°C)
Charging Parameter
Battery Charging Setting
Over Voltage Disconnect Voltage
12V
16V
Gel
24V
32V
Sealed
12V
24V
16V
32V
Flooded
12V
24V
16V
32V
Charging Limit Voltage
15.5V
31V
15.5V
31V
15.5V
31V
Equalize Charging Voltage
N/A
14.6V
29.2V
14.8V
29.6V
Boost Charging Voltage
14.2V
28.4V
14.4V
28.8V
14.6V
29.2V
Float Charging Voltage
13.8V
27.6V
13.8V
27.6V
13.8V
27.6V
Boost Reconnect Charging
Voltage
13.2V
26.4V
13.2V
26.4V
13.2V
26.4V
Low Voltage Reconnect Voltage
12.6V
25.2V
12.6V
25.2V
12.6V
25.2V
Under voltage warning reconnect
voltage
12.2V
24.4V
12.2V
24.4V
12.2V
24.4V
Under Voltage Warning Voltage
12V
24V
12V
24V
12V
24V
Low Voltage Disconnect Voltage
11.1V
22.2V
11.1V
22.2V
11.1V
22.2V
Discharging Limit Voltage
10.8V
21.6V
10.8V
21.6V
10.8V
21.6V
Equalize Duration
Boost Duration
Mechanical Parameter
Description
2 hours
2 hours
2 hours
2 hours
2 hours
Parameter
Overall dimension
140(5.51) x 65(2.56) x 34(1.34) mm/inches
Mounting dimension
130(5.12) x 45(1.77) mm/inches
Mounting hole size
Φ4.5
Terminal
6mm2
Net weight
0.15kg
www.solarpower-mart.com
Harvest the Sun power!
End of Page
www.solarpower-mart.com
Harvest the Sun power!
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement