RUNNING BOARDS
2019 DODGE RAM 1500 CREW CAB
PARTS LIST:
1 Driver/left side Pioneer Running Board
1 Passenger/right side Running Board
6 Universal Mounting Brackets (left or right)
18 8mm x 24mm x 2mm Washers
12 6mm x 20mm T-Bolts
12 6mm x 22mm x 2mm Flat Washers
12 6mm Lock Washers
12 6mm Hex Nuts
18 8-1.25mm Nylon Lock Nuts
Front
(6) Left or Right
Mounting Brackets
Driver/left side
Running Board
NOTE: The front of the Running
Board is triangular shaped.
PROCEDURE:
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED.
1. Start the installation under the driver side of the vehicle. Locate the front (3) factory studs along the inner side of the body panel, (Figure 1) .
2. Select (1) Mounting Bracket. NOTE : All (6) Brackets are universal and will fit left or right side.
Attach the Mounting Bracket to the (3) factory studs with (3) 8mm Flat Washers and (3) 8mm
Nylon Lock Nuts, (Figure 2) . Leave brackets loose at this time.
3. Repeat Steps 1 & 2 to install the Universal Brackets in the center and rear mounting locations along the body panel, (Figures 3 & 4) .
4. Carefully unwrap and select the Driver/left side Running Board. Use the illustration above to help determine the correct Running Board. Place the Running Board on top of the Brackets.
Locate the channel openings in the bottom of the Running Board. Select (6) 6mm T-Bolts,
(Figure 5) . Insert the T-Bolts into the channels in the bottom of the Running Board closest to the Brackets, (Figure 6) . Lift the Running Board up and guide the studs through the Brackets.
Page 1 of 3 05/03/18 (RA)300-
RUNNING BOARDS
2019 DODGE RAM 1500 CREW CAB
5. Attach the Running Board to the Brackets with (6) 6mm Flat Washers, (6) 6mm Lock Washers and (6) 6mm Hex Nuts, (Figures 7 & 8) . NOTE : The Running Board is designed to fit close to the vehicle. It may be necessary to loosen the Bracket hardware slightly and tilt the Brackets downward to insert the Running Board between the Brackets and the body.
6. Level and adjust the Running Board as necessary and fully tighten all hardware.
7. Repeat Steps 1—6 for Passenger/right side Running Board Installation.
8. Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment , wax this product after installing. Regular waxing is recommended to add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used also to clean the Running Board.
Driver/left Side Installation Pictured
Front
(Fig 1) Driver/left side front mounting location
(3) 8mm Flat Washers
(3) 8mm Nylon Lock Nuts
(Fig 2) Attach Bracket to the (3) studs
Front
(Fig 3) Driver/left side center mounting location
Rear
(Fig 4) Driver/left side rear mounting location
Page 2 of 3 05/03/18 (RA)300-
RUNNING BOARDS
2019 DODGE RAM 1500 CREW CAB
Driver/left Side Installation Pictured
(Fig 5) 6mm T-Bolt
Front
Front
(Fig 6) Insert 6mm T-Bolts through the channel openings in the bottom of the Running Board
(Fig 7) Driver/left side Running Board attached to Mounting Bracket at the front location
(2) 6mm Flat Washers
(2) 6mm Lock Washers
(2) 6mm Hex Nuts
(2) 6mm Flat Washers
(2) 6mm Lock Washers
(2) 6mm Hex Nuts
Front
(2) 6mm Flat Washers
(2) 6mm Lock Washers
(2) 6mm Hex Nuts
(Fig 8) Driver/left side Running Board attached to
Mounting Brackets at the center and rear locations
Page 3 of 3 05/03/18 (RA)300-
