Advertisement
Advertisement
RUNNING BOARDS
2019 FORD RANGER SUPERCAB
PARTS LIST:
2 Rattler Running Boards
1 Driver/Left Front Mounting Bracket
1 Passenger/Right Front Mounting Bracket
1 Driver/Left Center Mounting Bracket
1 Passenger/Right Center Mounting Bracket
1 Driver/Left Rear Mounting Bracket
1 Passenger/Right Rear Mounting Bracket
12 10-1.5mm x 25mm Hex Bolts
12 10mm Lock Washers
12 10mm x 27mm x 3mm Flat Washers
6 6mm x 1.0mm x 30mm Double Bolt Plates
12 6mm x 22mm x 2mm Flat Washers
12 6mm Lock Washers
12 6mm Hex Nuts
Passenger/Right Rear
Mounting Bracket
NOTE:
Passenger/
Right Center
Bracket has a hole in the top
Passenger/Right Center
Mounting Bracket
Passenger/Right
Front Mounting
Bracket
Driver/Left Center
Mounting Bracket
Driver/Left Front
Mounting
Bracket
Driver/Left Rear
Mounting Bracket
NOTE:
Driver/Left
Center
Bracket has a hole in the top
PROCEDURE:
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED.
1. Start the installation under the Passenger/Right side of the vehicle. Locate the front factory mounting location along the inner side of the body, (Figure 1) .
2. Remove the plastic plugs covering the mounting holes. Select Passenger/Right Front Mounting
Bracket. Attach to Passenger/Right front location with (2) 10mm x 25mm Hex Bolts, (2) 10mm
Lock Washers and (2) 10mm Flat Washers (Figure 2) . Do not tighten hardware at this time.
3. Locate the center threaded mounting holes. Select Passenger/Right Center Mounting Bracket.
Attach with (2) 10mm x 25mm Hex Bolts, (2) 10mm Lock Washers and (2) 10mm Flat
Washers, (Figures 3 & 5).
Do not tighten hardware at this time. NOTE: The Passenger/Right
Center and Rear Mounting Brackets look similar, the bottom tabs face opposite directions and there is a small hole on the top of the Passenger/Right Center Mounting Bracket, (Figure 4) .
4. Repeat Step 3 to install Passenger/Right Rear Mounting Bracket, (Figures 5 & 6) .
5. Carefully unwrap and select the (1) Rattler Running Board.
6. Place the Running Board on top of the Brackets. Locate the channel in the bottom of the
Running Board. Select (3) 6mm Double Bolt Plates. Insert the Bolt Plates into the channel in the bottom of the Running Board closest to the Brackets, (Figure 7) . Lift the Running Board up and guide the studs down through the Brackets.
7. Attach the Running Board to the Brackets with (6) 6mm Flat Washers, (6) 6mm Lock Washers and (6) 6mm Hex Nuts, (Figure 8) . Do not tighten hardware at this time.
8. Level and adjust the Running Board as necessary and fully tighten all hardware.
9. Repeat Steps 1 —8 for the Driver/Left side Running Board installation.
10. Do periodic inspections to the installation to make sure that all hardware is secure and tight.
Page 1 of 3 5/30/19 (AL) 600-
RUNNING BOARDS
2019 FORD RANGER SUPERCAB
To protect your investment , Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used also to clean the Running Board.
Passenger/Right Side Installation Pictured
Front
(Fig 1) Passenger/Right Front location
(2) 10mm Hex Bolts
(2) 10mm Lock Washers
(2) 10mm Flat Washers
(Fig 2) Front Bracket installation
Center Mounting
Brackets have a hole in the top.
(Fig 3) Passenger/Right Center location
(Fig 4) Passenger/Right Center and Rear
Mounting Brackets NOTE: The Center and Rear Mounting Brackets look similar.
The Tabs on the bottom are opposite.
Page 2 of 3 5/30/19 (AL) 600-
RUNNING BOARDS
2019 FORD RANGER SUPERCAB
Passenger/Right Side Installation Pictured
(2) 10mm Hex Bolts
(2) 10mm Lock Washers
(2) 10mm Flat Washers
(Fig 5) Center and Rear installation
(Center Bracket pictured)
(Fig 7) Double Bolt Plate installation
(2) 6mm Flat Washers
(2) 6mm Lock Washers
(2) 6mm Hex Nuts
(Fig 6) Passenger/Right Rear location
Front
(Fig 8) Passenger/Right
Running Board installation
Page 3 of 3 5/30/19 (AL) 600-

Public link updated
The public link to your chat has been updated.
Advertisement