Steelcraft 600-11800 Ford Ranger XL/XLT/Lariat Super Crew Cab 19-22 Guide
The Steelcraft 600-11800 is a heavy-duty commercial door operator designed for high-traffic applications. Its powerful motor and robust construction make it suitable for use in industrial, commercial, and institutional settings. The device features adjustable opening and closing speeds, allowing for precise control of door movement. Additionally, it includes a built-in obstruction detection system to ensure safe operation. The Steelcraft 600-11800 is a reliable and durable door operator that can withstand demanding use.
Advertisement
Advertisement
INSTALLATION INSTRUCTIONS
RATTLER RUNNING BOARDS
2019 FORD RANGERSUPER CREW CAB
RATTLER RUNNING BOARDS
2019 FORD RANGERSUPER CREW CAB
PARTS LIST:
2 78inch Rattler Running Boards
1 Driver/Left Front Mounting Bracket
1 Passenger/Right Front Mounting Bracket
1 Driver/Left Center Mounting Bracket
1 Passenger/Right Center Mounting Bracket
1 Driver/Left Rear Mounting Brackets
1 Passenger/Right Rear Mounting Bracket
Passenger/Right Center
Mounting Bracket
12 10-1.5mm x 25mm Hex Bolts
12 10mm Lock Washers
12 10mm x 27mm x 3mm Flat Washers
6 6mm x 1.0mm x 30mm Double Bolt Plates
12 6mm x 22mm x 2mm Flat Washers
12 6mm Lock Washers
12 6mm Hex Nuts
Driver/Left Center
Mounting Bracket
Passenger/Right Rear
Mounting Bracket
NOTE: DS/PS Center
Mounting Brackets have a hole in the top
Passenger/Right
Front Mounting
Brackets
Driver/Left
Front Mounting
Brackets
Driver/Left Rear
Mounting Bracket
PROCEDURE:
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED.
1. Start the installation under the Passenger/Right side of the vehicle. Locate the front factory mounting location along the inner side of the body, (Figure 1) .
2. Remove the plastic plugs covering the mounting holes. Select Passenger/Right Front Mounting
Bracket. Attach to Passenger/Right front location with (2) 10mm x 25mm Hex Bolts, (2) 10mm
Lock Washers and (2) 10mm Flat Washers (Figures 2 & 3) . Do not tighten hardware.
3. Locate the Center threaded mounting holes. Select the Passenger/Right Center/Rear
Mounting Bracket, look for the hole at the top of the bracket. Attach with (2) 10mm x 25mm
Hex Bolts, (2) 10mm Lock Washers and (2) 10mm Flat Washers, (Figures 4 & 5).
Do not tighten hardware at this time.
4. Repeat Step 3 to install Passenger/Right Rear Mounting Brackets, (Figures 6 & 7) .
5. Carefully unwrap and select the (1) Rattler Running Board.
6. Place the Running Board on top of the Brackets. Locate the channel in the bottom of the
Running Board. Select (3) 6mm Double Bolt Plates. Insert the Bolt Plates into the channel in the bottom of the Running Board closest to the Brackets, (Figure 8) . Lift the Running Board up and guide the studs down through the Brackets.
7. Attach the Running Board to the Brackets with (6) 6mm Flat Washers, (6) 6mm Lock Washers and (6) 6mm Hex Nuts, (Figures 9 & 10) . Do not tighten hardware at this time.
8. Level and adjust the Running Board as necessary and fully tighten all hardware.
9. Repeat Steps 1 —8 for the Driver/Left side Running Board installation.
10. Do periodic inspections to the installation to make sure that all hardware is secure and tight.
Page 1 of 3 REV 6/10/19(AL)
RATTLER RUNNING BOARDS
2019 FORD RANGERSUPER CREW CAB
To protect your investment , Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used also to clean the Running Board.
Passenger/Right Side Installation Pictured
Front
(2) 10mm Hex Bolts
(2) 10mm Lock Washers
(2) 10mm Flat Washers
(Fig 1) Passenger/Right Front location
Front
(Fig 2) Passenger/Right
Front Bracket installation
(Fig 3) Passenger/Right Front Bracket installed
Front
(Fig 4) Passenger/Right Center location
Page 2 of 3 REV 6/10/19(AL)
Front
(2) 6mm Flat Washers
(2) 6mm Lock Washers
(2) 6mm Hex Nuts
Front
RATTLER RUNNING BOARDS
2019 FORD RANGERSUPER CREW CAB
Passenger/Right Side Installation Pictured
(2) 10mm Hex Bolts
(2) 10mm Lock Washers
(2) 10mm Flat Washers
NOTE: The Center
Mounting Bracket has a hole in the top
(Fig 5) Passenger/Right Center installation
(Fig 7) Passenger/Right Rear installation
(Fig 9) Passenger/Right
Running Board installation
Front
(Fig 6) Passenger/Right Rear location
(Fig 8) Passenger/Right Bolt Plate installation
Front
(Fig 10) Passenger/Right Front
Running Board installed
Page 3 of 3 REV 6/10/19(AL)

Public link updated
The public link to your chat has been updated.
Advertisement