User Manual - AV-iQ
User Manual
Total Digital Connectivity Solutions
VGA I DVI-D / HDMI to Single Cat Transmitter
Universal Wall Interface
Model Name: UWITX
Cautions:
1. Digital Extender® logo is our own trademark of RTcom USA.,Inc.
2. Any of the products may be changed without any notice in order to improve the function
of the product.
3. The design and specification of the product may be changed without any prior notice.
Unpacking
Each Extender over single Cat cable package includes the following items;
- UWI Cat Transmitter
- 5V Power Adapter: 1 pc
- User manual
1-1 Contents
Contents
1-1
Description, General Specifications
1-2
Environmental Operation Conditions
1-3
Main Features
1-4
Video Connections and Operations
1-5
Mechanical Specifications
1-6
Technical Specifications
1-7
Warranty Informations
1-8
Troubleshootings
1-9
1-2 Description, General Specification
z Transmit VGA or DVI-D / HDMI signal to long distance using single Cat
cable
z UWI is designed with energy saving electrical circuit to connect with CR94M to expand VGA or Digital Input or use with our other CAT Extender
Receivers such as UBCA-RX or UBHD-RX(EDID limited).
z UWI uses Cat cable and is affected by cost and easy termination. The
best quality of Audio Visual signals can be achieved in every installation
sites and places.
ITEM
DESCRIPTION
Model Name
UWI-TX
Input Signal
VGA / DVI-D / HDMI*, STEREO AUDIO
Output Signal
TMDS
Resolution
Cat6e: 50m (164ft) at 1920*1080p
Cat6e: 50m (164ft) at 1920x1200
DC Power Jack (3.5mm Phoenix 2P)
VGA / DVI-D (HDMI) 29 pin Female
Receptacle
RS-232C port (3.5mm Phoenix 3P)
STEREO AUDIO JACK
RJ45
HDCP / EDID Support
Compliant / EEPROM
Power Consumption
DC 5V
Max 3 W
Dimension
103.9x90.5x31 mm
Weight
0.4Kg
*HDMI Adapter not included
1-3 Environmental Operation Conditions
Recommended environmental conditions for the operation are temperature range
of 10°C~40°C, non-condensing humidity levels of 10%-80%, and altitude ceiling
of 3,000 meters (9,840 feet).
Environmental limits for transportation are temperature range of -25°C~60°C,
non-condensing humidity levels of 5%~95%, and altitude ceiling of 15,000 meters
(49,200feet)
Environmental limits for storage are established at temperature range of 20°C~45°C, non-condensing humidity levels of 5%~95%, and altitude ceiling of
3,000 meters (9,840 feet)
The UWI Cat Transmitter is expected to function for more than 50,000 hours of
use at a 90% confidence level. The device is tested according to the identical
standards for testing LCD monitors.
1-4 Main Features
High Quality Picture - No Signal Loss and Adjust Free
UWI is built to transmit the high quality Video and Audio signals (Analog /
Digital) to preserve the native resolutions from the sources without signal loss
or stressed.
Signal Amplification
UWI gets external DC 5V power to run an internal chipset, which is designed to
amplifying the high quality Video and Audio signals to long distance.
Compact and Practical Design
Customers can enjoy our compact and practical design of UWI. UWI will make
simple installation and expand Analog / Digital Inputs.
Auto Detect Input Signals
UWI support auto detect function to input signals which are VGA or DVI and
Also User can select to sources thru the press button or RS232 command.
HDCP (High-bandwidth Digital Content Protection)
UWI fully compliant with HDCP.
Currently every digital sources are HDCP compliant. It will not display, if the
product are not HDCP compliant.
Compliance to DDWG Ver 1.0
UWI fully supports the DDWG Ver.1.0
Built in EDID Read and save functions
Built in EDID (Extended Display Identification Data) read function in EEPROM (Electrically
Erase Programmable Read-Only Memory), and can be saved EDID of non-VESA Standard
(Video Electronics Standards Association), including projectors into EEPROM by yourself.
**** EDID [Extended Display Identification Data] ****
EDID is defined by a standard published by the Video Electronics Standards
Association (VESA). The EDID includes manufacturer name, product type,
phospher or filter type, timings supported by the display, display size,
luminance data and (for digital displays only) pixel mapping data.
1-5 Video Connection and Operations
Step 1: Connect the Sources (VGA / DVI-D / HDMI / AUDIO) and Cat cable to UWI,
and connect Cat cable from UWI to appropriate Receiver or CR-94M.
Step 2: Connect power adapter (Will power ON automatically)
Step 3: Power ON the appropriate Receiver or CR-94M including sources and
display.
(UWI will detect sources automatically if one of Input port is not connected.
Or select Input with Input select Button.)
Step 4: Select EDID Data using EDID Rotary Switch and press EDID Learn button.
(1920*1080P will be default set up.)
DVI/HDMI audio switching thru RS-232 command(Refer 1-7 Technical specification)
EDID data saving (Set Mode 0):
Using this function: When Video is not display correctly or can not find correct EDID data on
Internal (Pre-saved) EDID table.
Step 1: Connect VGA or DVI Input port on UWI to display such monitor/projector directly,
Step 2: Power up the display and UWI.
Step 3: Select the source port VGA or DVI
Step 4: Set the number 0 on rotary switch.
Step 5: Press EDID Learn Button for 2~4 seconds. (Green Status LED is on, then it is
proceeding.)
Step 6: Green Status LED will be illuminated for about 2-3 second if EDID was saved
correctly.
z
z
z
If EDID was not saved correctly, Green Status LED will blink. In this case, go back to Step 4.
Must press EDID learn Button after selected one of EDID data.
Should EDID save to correct port such as VGA or DVI
Number
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
EDID Data
EXTERNAL(EDID data save mode)
800*600
1024*768
1280*768
1280*1024
1360*768
1366*768
*VGA N/A
1400*1050
1600*900
*VGA N/A
1600*1200
1680*1050
*VGA N/A
1920*1200
1280*720P/1920*1080i Audio *VGA N/A
1920*1080P 2ch Audio
1920*1080P 5ch audio
*VGA N/A
RESERVED
* N/A=Not available
1-6 Mechanical Specification
Dimension: 103.9x90.5x31 mm
Functioning part
PC INPUT : PC (VGA) Input port
DVI INPUT : DVI-D Input port
HDMI INPUT: Using HDMI to DVI Adapter
AUDIO IN: Stereo Audio Input port
CAT: RJ45 TMDS signal output port
DC-5V: power input port
TxD RxD GND: Sources select through RS232 command/ Firmware update
Display part
INPUT SELECT BUTTON: VGA or DVI / HDMI input selection switch
EDID LED: Display the status of EDID (Saving and Changing)
EDID LEARN BUTTON: EDID data save button (Internal and External)
EDID ROTARY SWITCH: Internal (Pre-saved) EDID select switch
PC LED: Display the status of VGA signal
DVI / HDMI LED: Display the status of DVI / HDMI signal
1-7 Technical Specification
Data transmission speed: 2.25 Gbps (Single Link)
Digital Video Bandwidth: 25~225 MHz
Resolution: Up to WUXGA (1920x1200)@60Hz, 1080p
DVI Version 1.1 Compliance with Stereo Audio
Input/Output signal standard: VGA, DVI-D (HDMI with Adapter), Stereo Audio
Maximum length: [email protected], 1080p->Cat6e UTP 550MHz: 50m (164ft)
Cat5e: 30m (100ft)
Transmitter connector: VGA, DVI-D 29P/STEREO JACK/RJ-45/3.5mm Phoenix
2P(power)+3P(RS232-TX/RX/Ground)
Power consumption: 3 Watts (Max)
Power supply: DC 5V, 2A
UTP Cat Cable terminations
TIA/EIA-568-B,
TX (A): 1------ -> RX: 1(Orange/White)
TX (A): 2------ -> RX: 2(Orange)
TX (B): 3 -------> RX: 3(Green/White)
TX (B): 4 -------> RX: 4(Blue)
TX(C): 5 -------> RX: 5(Blue/White)
TX(C): 6 -------> RX: 6(Green)
TX (D): 7------ -> RX: 7(Brown/White)
TX (D): 8------ -> RX: 8(Brown)
• We do not recommend the punch down terminations.
• We do not recommend the STP(Shielded Twisted Pair) cable.
RS-232 Command
Baud rate: 19200 bps, Data bits: 8 bit, Stop bits : 1 bit, Parity, Flow control: None
==========================================================
Command(CON) + Data(DVI) + Enter
==========================================================
¾
DVI/VGA Video switch
1. CON DVI
2. CON VGA
3. CON ATS
4. CON ATE
¾
: Switch to DVI
: Switch to VGA
: Auto switch mode Enable
: Auto switch mode Disable
DVI plus Stereo audio or HDMI MODE SELECT
AUD DIG : HDMI Mode
AUD 3.5: 3.5 stereo audio select
Whenever you use HDMI embed audio you should set EDID to “D” which is
[email protected], 2ch audio
Firmware Upgrade Procedure for UWI
Step1: Connect RS232 cable end to a COM port on your PC and connect the other end
To a Tx/Rx/GND on UWI back panel
Step2: Connect power cable to +5V/GND on UWI back panel
Step3: Extract the MegaLoad program and UWI-TX-x.x.hex files
Step4: Double click the Megaload program(WinXP) and OPEN File to be programmed in
the flash with UWI-TX-x.x.hex
Step5: Select ComPort and Speed to 19200bps
Step6: Click the Send Reset button and will be move progress bar
Step7: Disconnect power and other cables.
1-8 Warranty Information
3 (Three) Year Warranty
RTcom USA warrants the UWI Cat Transmitter to be free from defects in workmanship and
materials, under normal use and service, for a period of thee (13) year from the date of
purchase from RTcom USA or its authorized resellers.
If a product does not work as warranted during the applicable warranty period, RTcom USA
shall, at its option and expense, repair the defective product or part, deliver to customer an
equivalent product or part to replace the defective item, or refund to customer the purchase
price paid for the defective product.
All products that are replaced will become the property of RTcom USA.
Replacement products may be new or reconditioned.
Any replaced or repaired product or part has a ninety (90) day warranty or the reminder of the
initial warranty period, whichever is longer.
RTcom USA. shall not be responsible for any software, firmware, information, or memory data
of customer contained in, stored on, or integrated with any products returned to RTcom USA for
repair under warranty or not.
Warranty Limitation and Exclusion
RTcom USA shall have no further obligation under the foregoing limited
warranty if the product has been damaged due to abuse, misuse, neglect,
accident, unusual physical or electrical stress, unauthorized modifications,
tampering, alterations, or service other than by RTcom USA or its authorized
agents, causes other than from ordinary use or failure to properly use the
product in the application for which said product is intended.
For support, please call Tel: 1-973-862-4210.
Or send the Email: [email protected]
1-9 Troubleshooting
The UWI Cat Transmitter is designed for years of trouble free service, please
reference the troubleshooting chart below if experiencing issues with the device.
Problem
No picture (or signal)
Solution
1. Ensure the status LED is illuminated.
2. Check UWI Transmitter is properly connected with
sources.
3. Check Cat cable connecter is properly terminated
TIA/EIA-568B.
4. Set EDID correctly for VGA or DVI
(Refer 1-5 Video Connection and Operations)
5. Power cycle source device after the connection of
Cat cable.
Poor picture or noise
1. Restart the CR-94 or source device
2. Unplug DC power adapter, disconnect DVI / HDMI or
VGA cable, reconnect the cables and Replug power
adapter.
3. Check electric ground level of power for devices
4. Make sure that selected EDID is same as of display
(Refer 1-5 Video Connection and Operations)
No Sound
1. Make sure that the selected proper source.
2. Set the HDMI source to RS232 command
(Refer 1-7 Technical Specification)
© 2012 RTcomUSA All Rights Reserved
Revision 2 62012
RTcom USA, Inc. Locations
RTcom USA, Inc.
10 Millpond Road, unit 2
Lafayette, NJ 07848
Tel: 1-973-862-4210
Fax: 1-973-741-2116
www.digitalextender.com
For order support, please contact your Distributor or Reseller.
Send the Email:[email protected]
For technical support,
Tel: 1-973-862-4210
[email protected]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement