Midori Sno-King
Instruction Manual
Model #1888W
Part No. 12666
Revised: June 2009
Cincinnati, OH 45241-4807 USA
Sno-King
Safety Precautions
All Models #1888 2
Sno-King
Forward
This manual covers the Midori Sno-King Ice Shaver Machine, model number 1888W.
Installation Instructions
Inspection of Shipment:
Unpack all cartons and check thoroughly for any damage that may have occurred during transit.
Damage claims should be filed immediately with the transportation company. Gold Medal is not responsible for damage that occurs in transit.
Setup:
Your new Midori Sno-King Ice Shaver Machine is assembled and tested at the factory.
Remove all packing material and tape before starting operation.
Electrical Requirements:
The following power supply must be provided:
Model No. 1888W:
.
120 VAC, 60 Hz. 972 Watts 8.1 Amps
Your electrician must furnish sufficient current for proper machine operation. We recommend this ice shaver machine be on a dedicated and circuit protected line. Failure to wire properly will void the warranty and can result in damage to the heat elements, light, motor and etc.
It is Gold Medal Products Company’s recommendation that this machine be plugged directly into a wall outlet. The use of extension cords is not recommended due to safety risks1 and the popper’s performance will be sacrificed/reduced.
Before You Plug In Machine:
1. Make sure that the wall outlet can accept the three (3) prong grounded plug on the power supply cord.
2. The wall outlet must have the proper polarity. If in doubt, have a competent electrician inspect the outlet and correct if necessary.
3. DO NOT use a three (3) prong grounded to two (2) prong un-grounded adapter.
3 All Models #1888
Sno-King
Machine Operation
Ice Requirements
The Midori Sno-King can use small or medium ice cubes approximately 2 to 3 inches in size.
NOTE: The ice will not enter the shaving chute if the pieces are too large.
Operating the Sno-King
1. Turn power on.
2. Raise hopper lid.
3. Fill hopper with Ice.
5. Press momentary switch to shave.
NOTE:
Never allow any foreign or metallic objects around the shaver area of the Sno-King. Ice picks, scoops, and other miscellaneous debris that may be in the ice can often damage blades.
Harder ice will result in finer snow, while soft ice will result in coarser snow.
4 All Models #1888
Sno-King
Installing New Shaving Blades
Inspect your equipment before replacing the blades. With the POWER switch OFF and the machine unplugged, use a flashlight to examine the blades in the shaver body. If the blades appear to be nicked or bent, then the blades should be replaced.
Follow this procedure:
1. Unplug the main power supply cord from the electrical outlet.
2. Remove the shaver head from the motor shaft by loosening the Allen head set screws between the motor and the hopper.
3. Remove the shaver head. Pull the shaver head off of the motor shaft and through the hopper. If the shaver head is frozen onto the shaft, remove the hold down bolts on the motor. Pull the motor back, trapping the shaver head against the inside of the hopper, until the shaver head disengages.
4. After removing the shaver head, check the motor shaft for burrs and corrosion. Use a fine tooth file to remove the burrs and corrosion.
5. Remove the blades from the shaver head. These blades may be re-sharpened, but it is far better to replace the old blades with a new set.
6. Position the new blades and insert screws until they are finger tight.
7. Set the blade thickness equal to a dime. (See illustration below.) Make sure that the height is even across the shaver head.
8. Tighten the blade screws completely. Check the blades again with a dime to ensure the blades did not move while tightening the screws.
9. Replace the motor and shaver head. Mount the motor using the hold down bolts. Insert the shaver head through the hopper and onto the motor shaft. Press the shaver head onto the motor shaft with the pusher handle, then move the shaver head in another 1/8".
Check that the shaver head is not rubbing against the back of the hopper and the blades are not touching the pusher handle.
10. Replace the set screws between the hopper and the motor.
NOTE: Replace any shims that were between the motor base and the mounting surface.
SET TOP OF BLADE
FLUSH WITH HEIGHT
GAGE, AS SHOWN
HEIGHT GAGE
(USE A DIME)
SHAVER HEAD
5
SHAVER BLADE
BLADE MOUNTING SCREW
All Models #1888
Sno-King
MAINTENANCE INSTRUCTIONS
6 All Models #1888
Sno-King
ORDERING SPARE PARTS
1. Identify the needed part by checking it against the photos, illustrations, and/or the parts list.
2. When ordering, please include part number, part name, and quantity needed.
3. Please include the machine’s model name, serial number, and date of manufacture (located on the machine nameplate) with your order.
4. Address all parts orders to:
Parts Department
Gold Medal Products Co.
10700 Medallion Drive
Cincinnati, Ohio 45241-4807
(800) 543-0862
(513) 769-7676
Fax: (513) 769-8500
E-mail:
or, place orders at:
Web Page:
www.gmpopcorn.com
7 All Models #1888
Sno-King
#1888W ASSEMBLY
Motor p/n 12456
Fan Grate p/n 74746
Front Panel p/n 12698GSP
Drain Fitting p/n 12668
Midori Rack p/n 67921
Side Panel p/n 12648G
Lead-In Cord p/n 22038
8 All Models #1888
Sno-King
Cover Plate p/n 22709
Warning Label p/n 44019
Momentary Switch p/n 38971
Switch, Lighted Rocker p/n 42798
Door p/n 1889
Sno-Kone Tray p/n 1076W
9 All Models #1888
Sno-King
SHAVER HEAD - 22015
Set Screw 1/4 -20 X 3/8 p/n 74125
Shaver Head p/n 22015
Blade Assembly p/n 22018
10 All Models #1888
Sno-King
ELECTRICAL SCHEMATIC
MODEL #1888
11 All Models #1888
Sno-King
WARRANTY
WE WARRANT to the original purchaser the Gold Medal equipment sold by us to be free from defects in material or workmanship under normal use and service. Our obligation under this warranty shall be limited to the repair or replacement of any defective part for a period of six (6) months from the date of sale to the Original
Purchaser with regard to labor and two (2) years with regard to parts and does not cover damage to the equipment caused by accident, alteration, improper use, voltage, abuse, or failure to follow instructions.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXP RESSED
OR IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR
PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTIBILITY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION
ON THE FACE HEREOF. We neither assume, nor authorize any other person to assume for us, any other obligation or liability in connection with the sale of said
GOLD MEDAL equipment or any part thereof.
The term “Original P urchaser” as used in this warranty shall be deemed to mean that person, firm, association, or corporation who was billed by the GOLD MEDAL
PRODUCTS COMPANY, or their authorized distributor for the equipment.
THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL
PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS COMPANY AT 1-800-
543-0862 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE
EQUIPMENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS
CONCERNING THE REPAIR OR REPLACEMENT OF PARTS.
NOTE: This equipment is manufactured and sold for commercial use only.
GOLD MEDAL PRODUCTS COMPANY
10700 Medallion Drive
Cincinnati, Ohio 45241-4807 USA www.gmpopcorn.com
Phone: 1-800-543-0862
© The text, descriptions, graphics and other material in this publication are the proprietary and exclusive property of Gold Medal Products Company and shall not be used, copied, reproduced, reprinted or published in any fashion, including website display, without its express written consent.
12 All Models #1888
