Error messages Factory settings USER MANUAL Contents -

Error messages Factory settings USER MANUAL Contents -
USER MANUAL
Error messages
If a fault or error occurs, the thermostat will display an error code as
follows:
EO: Internal failure.The thermostat is defective. Replace thermostat.
E1: Internal sensor defective or short-circuited.
E2: External sensor defective or short-circuited.
E5: Internal overheating. Inspect the installation.
Contents
Factory settings
-
M e n u ........................................................................................ ®
Introduction..............................................................................7
First time settings......................................................................7
General operation..................................................................... 8
Preset schedule
Day 1-5
Back................................................................... ..................8
With floor sensor
With room sensor
Exit.......................................................................................8
Operation mode....................................................................... 9
Auto m o de.......................................................................... 9
Event
Time
Morning
06:00-08:00
25 °C
20 nC
108:00-16:00
20 °C
15 °C
Manual mode...................................................................... 9
Comfort mode......................................................................9
Daytime 2
08:00-16:00
20 °C
15 °C
Thermostat setup menus........... ...............................................9
Evening
16:00-23:00
25 nC
20 °C
Evening 2
16:00-23:00
25 °C
20 °C
Event settings........................................................................... 9
User settings...........................................................................11
Time and d ate.................................................................... 11
Night
23:00-06:00
20 DC
15 °C
Daytime
Day 6-7
Event
Time
Day
08:00-23Ю0
1Night
23:00-08:00
With floor sensor
|
With room sensor
25 °C
20 °C
20 °C
15°C
Child lock...........................................................................11
Display settings................................................................. 11
Event schedule..................................................................
Energy m onitor......................... ........................................13
Engineer settings.................................................................... 13
Offset temperature............................................................ 13
Adaptive function ........................................... ................. 14
Application .............................. ........................................ 14
Temperature scale.............................................................. 14
Language..........................................................................
Factory reset...................................................................... IS
Information........................................................................
Back...................................................................................15
KIMA Heating Cable AB
www.kima.se
14
Exit.................................................................................... 15
Error messages....................................................................... 16
Factory settings......................................................................
Preset schedule................................................................. ^
Extrem e Combi
•English
Extrem e Combi
E n g lis h
Menu
Display illumination
«08УЯ5— g j
There are three settings for the display
0 20°C
backlighting:
BacMght
• Auto: Backlighting is activated whe­
Comfort Menu Manual
P
8;
never a key is pressed and goes out
I
Event settings
Engineer settings
el
Exit
automatically 30 seconds after the last
<
OK
►
key press.
• On: Backlighting continuously on.
Time and date
6 -
Offset temp.
■А Й
1
1
Child iock
Adaptive function
©
0
Language
Application
f it
1
i
Event schedule
Temp scale
Energy monitor
sss%
Back
«0
Exit
by the thermostat.
Select the desired backlighting setting and confirm with OK.
№
1
Display settings
• Heating active: Backlighting comes on when heat is called for
ff
Backlight
Allows the language used on the display
to be changed.
4
Factory reset
Allows factory settings to be restored.
Your personal settings will be lost, see
I
information
CD
OK
menu. Confirm with OK.
t
P
Factory reset
*c£l
Factory settings.
Press OK and choose Reset in the
Factory reset
P
guage. Confirm with OK.
I
P
❖
IT1
Language
Press OK and select the required lan­
.. . 9
Language
Q
<
ok
у
Information
Displays the thermostat software
version.
Back
Information
^
~
In various parts of the menus and sub­
Exit
menus you will find the Back menu item.
!►
Use Back to return to the last step.
_J
CD
<
OK
►
Exit
Returns to initial dispay.
4
13
E x te rn * Combi
:xtferne Combi
Adaptive function
Ensures that the required temperature
1
a
.*
Adaptive function
has already been reached when you get
I
up in the morning or come home from
work. After just a few days, the adaptive
4
OK
►
called events. Lowering the temperature when the home is unoc­
The thermostat comes with a default schedule suitable for most
Press OK and set the function to On. Confirm with OK.
homes. Unless you change the settings, the thermostat will operate
in compliance with the default schedule.
Application
Furthermore, the thermostat also features an adaptive function
Set the type of regulation used.
There are 4 options:
i
e:
t
The thermostat regu­
Application
lates floor temperature
only. A floor sensor
ft
<
as the seasons change, and takes this into account when turning
temperature at the desired time. The adaptive function's fuzzy logic
OK
t
must be connected.
takes three days to determine the heat characteristics of the room
before it operates efficiently.
The thermostat regulates room temperature only.
Room/limit:
The thermostat regulates room temperature with
min. and max. limits for floor temperature. A floor
sensor must be connected.
First time settings
The first time you switch the power switch ON "I", language, time and
The thermostat functions as a simple regulator
date must be set.The menu will automatically guide you through the
and no sensors are used. The setting is a percen­
tage.
process.
• Choose your language with the Up and Down buttons and
Press OK and select the required application. Confirm with OK.
confirm with OK.
• Set the actual hour and press the OK button.Then set the
Temperature scale
minutes. Press OK.
Allows you to set the temperature range
Q
within which the thermostat can be set.
The next menu allows you to select the application you want the ther­
&
rature within this range in auto, comfort
i
OK
'
• Set the actual date: year, month and day. Confirm the settings
with the OK button.
Temp scale
It is then only possible to set a tempe­
and manual mode.
that determines how long the floor takes to heat up and cool down
the heating on or off. This ensures that the room is always up to
Room reg.:
>
Press OK to highlight Min temperature. Use the up or down button
to select the minimum permissible temperature. Press OK and
select the maximum permissible temperature. Confirm the settings
with OK.
ned times on different days of the week. For each day of the week,
cupied wyi reduce your energy costs without reducing comfort.
lated when the heating must be turned on.
Regulator:
The thermostat can switch on your heating system at predetermi­
you can set individual temperatures for 4 or 6 separate periods,
function will have automatically calcu­
Floor reg.:
English
Introduction
mostat to control. If the thermostat is intijg room to be heated, select
Room/l/m/t. The best way to control underfloor heating is with just a
floorsensor, select Floor and press OK.
You now need to select the actual floor covering so that the thermostat
can take this into account during operation. Select the actual floor
covering and press OK.
You now need to enter the system load, the total wattage installed in
the floor and output of the powered by the thermostat. Select the ap­
propriate load and press OK.
12
5
Extreme C o m
b i _______________________________________ English
English
The thermostat is now ready for use and your underfloor heating
Energy monitor
will operate in accordance with the pre-programmed Event sche­
Allows you to view energy consumption
dule. See Factory Settings for full details of this.
for the past 2 days, 30 days or 365 days.
H
Energy monitor
sss%
Press OK for the chosen period.The
value in per cent (%) shows the relative
4
OK
►
amount of time the heating has been on.
The following figure is the cost for the selected period. To ensure
1
1
f
correct calculation, check the settings for currency, price per kWh
■ H M ^W ed
and toad.
/ 'Т ч
Currency:
Power switch
'1
1
'
20°C
Press OKand chose the required currency.
Confirm with OK.
Cost/unit:
Comfort Menu Manual
Press OK and set the actual cost of electricity.
The cost must be entered per kWh. Press OK.
Load: Press OKand enter the connected heating power.
Г' '
Г
“
ЛГ
~r
’
The value must be in watt (W). Press OK.
Leave the menu by pressing Exit.
Navigation buttons
The Engineer settings menu contains the
The power switch button allows you to turn the thermostat on "I" and off
following options:
"0"by sliding the button up and down. When the thermostat is switched
• Offset temperature
off"0", the relay disengages. All settings, including time and date, will be
• Adaptive function
remembered.
• Application
The thermostat is intuitively operated using the navigation buttons.
• Temperature scale
The function of each button is indicated above the button in the
• Language
display.
5»
Engineer settings
General operation
Engineer settings
h
<
OK
>
• Factory reset
• Information
Back
In various parts of the menus and submenus you will find the
Offset temperature
Back menu item.
If the actual measured temperature does
~
'
Use Back to return to the last step.
not corresponding to the thermostat
%
I Э
Offset temp.
value, you can adjust the thermostat by
Exit
offsetting the temperature.
Returns to initial dispay.
Press OK and enter the value of the
measured temperature. Confirm with OK.
б
<
OK
t
English
Operation mode
Press the OK button to select or deselect the display options. Then
The thermostat features three different modes of temperature
select Exit in the menu to return to the initial display and view your
control:
chosen settings.
* Only with floor application.
Auto mode
'
© Select Auto if you want the temperature to be controlled auto­
Event schedule
Allows you to choose the type of weekly
Event schedule you require.
5:2 4-event:
Monday to Friday with 4
H
Event schedule
events and Saturday to
6:1 4-event:
sss%
p
matically via the 4 or 6-event schedule.
Manual mode
Select Manual to cancel the programmed Event schedule (e.g.
4
OK
►
during holidays) and to set the required temperature manually. You may,
Sunday with 2 events.
for example, want to adjust the temperature to 15°C for frost protection
Typically used if you work from Monday to Friday.
while you are away.
Monday to Saturday with 4 events and Sunday
• Press Manual, confirm with OK and choose the required tempe­
with 2 events. Typically used if you work from
rature.
Monday to Saturday.
7:0 4-event:
Monday to Sunday with 4 individual events. Allows
you to choose individual programs for each of the
7 days of week.
5:2 6-event:
Monday to Friday with 6 events and Saturday
and Sunday with 2 events. Typically used if you
6:1 6-event:
Comfort mode
o o
Se|ect Comfort to set a temporary comfort temperature
I
0 У <
s0' called party mode) for a single event.
. Press Comfort, confirm with OK and choose the required tem­
perature. Then enter the required duration of comfort mode.
work from Monday to Friday.
After the set time has elapsed, the thermostat will automatically
Monday to Saturday with 6 events and Sunday
revert to Auto mode.
with 2 events. Typically used if you work from
Monday to Saturday.
7:0 6-event:
Monday to Sunday with 6 events. This allows
Thermostat setup menus
you to choose individual programs for each day
The menu allows you to select the following options:
of the week.
0:7 6-event:
■
Monday to Sunday with 6 events and the same
program for all days of the week.
Event settings
Select the required 4 or 6 event schedule and confirm with OK.
Allows you to have the temperature
For instructions on programming the time and temperature for the
controlled automatically in accordance
Event schedule, see Event settings.
with a program of your own choice. You
1 €1
Й
Event settings
eft
<
OK
►
can select temperature settings for 4 or
6 different events during the day:
7
10
E x tre m e C o m b i______________________________
4-Events*
User settings
6-Events*
In the user settings menu you can
Morning
Morning
Irn g ih h
01
User settings
change the following items:
• Time and date
1 Й »
Daytime
Daytime
• Child lock
'
<
OK
>
• Display settings
t f p f 4 Evening
Daytime 2
• Event schedule
• Energy monitor
Night
Evening
Time and date
Evening 2
©I
Press OK and set the actual time in
hours and minutes.
D
Night
Time and date
©
The date will then be displayed. Set the
date and confirm with OK.
<
OK
►
* Depending on the chosen schedule, see User Settings/Event
Child lock
schedule.
Allows you to lock the thermostat
©
P
The thermostat is pre-programmed with a Event schedule for easy
settings, e.g. in public or other places
and economic heating control, see Preset schedule under Factory
where you do not want the settings
settings. The schedule can be easily changed in the following way:
changed.
1. Press the OK button to activate the Event settings display.
using the down button. Confirm with OK.
2. Choose the days for which you want to change the settings,
The child lock can be unlocked by pressing both the Comfort and
Press OK and set the child lock to On
Mon-Fri or Sat-Sun using the up or down button. Press OK.
Child lock
©
4
OK
^
Manual buttons simultaneously for 5 seconds.
3. Now select the time and temperature for each daily event in the
program. Press OK and set the start time for the event concer­
Display settings
ned. Confirm with OK. Set the temperature for this event and
Allows you to select what is shown on
confirm with OK.
the initial display.
4. After setting the required events, select Exit in the menu to
return to the initial display.
'
Time/day:
'
and day at the top of the
Time
__ /
Max
Min
08:00
ж
ti
ВШ Й
OK
p
о
06:00
■v
/
Set temp.:
5.0°C
ж
OK
В
Display settings
□
Shows the actual time .
display.
Temp
©
<
OK
>
Shows the current temperature setting.
Act. temp*.
Shows the actual measured temperature.
Scr. saver:
Switches off the display after 30 seconds if no but­
ton is pressed. Any subsequent press of a button
reactivates the display. The thermostat remains on
and runs the selected program.
8
9
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement