speed dome operating manual

speed dome operating manual
XP1080S20
Quick Installation Speed Dome Installation Manual
Version 1.0
Table of Contents
1
QUICK INSTALLATION SPEED DOME INSTALLATION ........................................7
1. 1
Installation Preparation ........................................................................................................................................7
1. 2
Installation ................................................................................................................................................................8
1.2.1
Address and Baud Rate Setup .................................................................................................................... 8
1.2.2
Install the transparent cover ......................................................................................................................... 9
1.2.3
Install the speed dome.................................................................................................................................. 10
1. 3
Initial Setup ........................................................................................................................................................... 12
1. 4
Dial Switch Setup................................................................................................................................................ 12
1.4.1
Communication protocol and Baud rate ................................................................................................. 12
1.4.2
Address Setup ................................................................................................................................................. 13
2
BRACKET DIMENSIONS ........................................................................................... 14
2. 1
Wall mount bracket............................................................................................................................................. 14
2. 2
Hanging mount bracket (Multiple Lengths) ................................................................................................ 14
2. 3
Corner mount bracket........................................................................................................................................ 15
2. 4
Pole mount bracket ............................................................................................................................................ 15
3
WALL MOUNT BRACKET INSTALLATION ............................................................ 16
3. 1
Component Installation ..................................................................................................................................... 16
3. 2
Installation ............................................................................................................................................................. 16
3.2.1
Installation Requirements ............................................................................................................................ 16
3.2.2
Installation Steps ............................................................................................................................................ 16
2
4
HANG MOUNT BRACKET INSTALLATION............................................................ 18
4. 1
Component Installation ..................................................................................................................................... 18
4. 2
Installation ............................................................................................................................................................. 18
4.2.1
Installation Requirements ............................................................................................................................ 18
4.2.2
Installation Steps ............................................................................................................................................ 18
5
CORNER MOUNT BRACKET INSTALLATION ...................................................... 20
5. 1
Component Installation ..................................................................................................................................... 20
5. 2
Installation ............................................................................................................................................................. 20
5.2.1
Installation Requirements ............................................................................................................................ 20
5.2.2
Installation Steps ............................................................................................................................................ 20
6
POLE MOUNT BRACKET INSTALLATION............................................................. 22
6. 1
Installation ............................................................................................................................................................. 22
6.1.1
Installation Requirements ............................................................................................................................ 22
7
APPENDIX Ⅰ THUNDER PROOF AND SURGE PROTECTION .......................... 24
8
APPENDIX Ⅱ ABOUT RS485 BUS .......................................................................... 25
8. 1
RS485 Bus Main Feature................................................................................................................................. 25
8. 2
RS485 Bus Transmission Distance .............................................................................................................. 25
8. 3
The Problem in Practical Use ......................................................................................................................... 25
8. 4
RS485 Bus FAQ.................................................................................................................................................. 26
3
Welcome
Thank you for purchasing our speed dome!
Please read the following safeguards and warnings carefully before you install or use the
product!
4
Important Safeguards and Warnings
Safety Measures
Qualified Engineer Needed

The installation engineer or maintenance engineer shall have corresponding CCTV system
installation certificate or maintenance qualification certificate.

The installation engineer or maintenance engineer shall have qualification certificate for work
at height.

The installation engineer or maintenance engineer shall have the basic knowledge and
operation technique for low-voltage cable layout and low-voltage electronic cable connection.

Please read the installation manual carefully and keep it well for future reference,

We are not liable for any problems caused by unauthorized modifications or attempted repair.
Lifting Appliance Requirement

Please select the proper speed dome installation mode and use the lifting appliances at the
safety environment.

The lifting appliances shall have the enough capacity to reach the installation height.

The lifting appliances shall have safe performance.
Precautions
5
Safety Transportation

Heavy stress, violent vibration or water splash are not allowed during transportation, storage

and installation.
This series product must use split type package during the transportation.

We are not liable for any damage or problem resulting from the integrated package during
the transportation.
When device is malfunction
Shut down the device and disconnect the power cable immediately if there is smoke, abnormal
smell or abnormal function. Please contact your local retailer ASAP.
Do not try to dismantle or modify the device


There is risk of personal injury or device damage resulting from opening the shell.
Please contact your local retailer if there is internal setup or maintenance requirement.

We are not liable for any problems caused by unauthorized modifications or attempted repair.
Do not allow other object falling into the device

Please make sure there is no metal or inflammable, explosive substance in the speed dome.

The above mentioned objects in the device may result in fire, short-circuit or damage.

Please shut down the device and disconnect the power cable if there is water or liquid falling
into the camera. Please contact your local retailer ASAP.

Please pay attention to the camera. Avoid the sea water or rain to erode the camera.
Handle carefully
Do not allow this series product fall down to the ground.
Avoid heavy vibration.
Installation Environment Requirement

This series speed dome should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.

This series product shall be away from the strong electromagnetism radiant, please keep it
away from wireless power, TV transmitter, transformer and etc.
Daily Maintenance

Please use the soft cloth to clean dust on the shell, or you can use soft cloth with cleaning

liquid to clean the shell and then use soft cloth to make it dry.
Do not use gasoline, dope thinner or other chemical material to clean the shell. It may result
in shell transfiguration or paint flake.

Do not allow the plastic or rubber material to touch the shell for a long time. It may result in
paint flake.
6
1 QUICK INSTALLATION SPEED DOME INSTALLATION
1.1 Installation Preparation
Basic Requirement

All installation and operation here should conform to your local electrical safety codes.

Before installation, please open the package and check all the components are included.
Please make sure the speed dome installation environment and installation mode can meet
your requirement. If there is special requirement, please contact your local retailer for more
information.

We assume no liability or responsibility for all the fires or electrical shock caused by
improper handling or installation.
Check installation space and installation location intension
Please make sure the installation environment has enough space to install the speed dome and
its corresponding bracket.
Please make sure the ceiling, wall and the bracket can support the speed dome and its
corresponding installation component. The safety factor shall be 4X.
About cable
Please select the cable according to your transmission distance.
The minimum video coaxial-cable requirement is:
 75 ohm.
 Full cable with copper conductor

95% knitted copper shield
International Model
RG59/U
RG6/U
RG11/U
Max Distance
(Ft\M)
750ft (229m)
1,000ft (305m)
1,500ft (457m)
Set dial switch button
Set dial switch button according to control protocol and speed dome address. (Please refer to
user’s manual for detailed information.)
Please keep all package material well for future use
Please keep speed dome package material well in case you need to send it bac k to your local
retailer or manufacturer for maintenance work.
Non-original package material may result in device damage during the transportation.
Check Accessories
Before the installation, please check the accessories one by one according to the packing list.
Please make sure all the components listed are includes.
Important:
The quick installation speed dome power is AC 24V/3A.
7
1.2 Installation
Please note the quick installation speed dome includes the quick installation high speed dome,
IP quick installation speed dome, tracing quick installation high speed dome, quick installation
medium speed dome.
The speed dome has several types of installation brackets. You can refer to the following
contents for detailed information. Here we are going to install the speed dome in wall mount
bracket.
Open the transparent cover and take out the packing material EPE around the speed dome driver.
Please remove the protective paster from the driver and take off the camera lens cap. See Figure
1-1.
Figure 1-1
1.2.1 Address and Baud Rate Setup
Now you can set the quick installation speed dome address and baud rate. The speed dome
interface is shown as below. See Figure 1-2. There are two dial switches: SW1 and SW2. Here
you can set the address, baud rate, communication protocol and etc. Please refer to chapter 1.4
for detailed information.
Figure 1-2
8
1.2.2 Install the transparent cover
First, you need to check the steel wire of the bracket is firmly secure or not.
Please line up the captive screws to the quadrate groove of the bracket and then push the
bracket into the internal enclosure. Fix these two captive screws. See Figure 1-3.
Figure 1-3
Now you can install the quick installation port. Please twist Teflon tape around the screw thread
of the quick installation port and turn it into the screw thread of the wall mount bracket. Use M4
stainless screws to secure firmly. See Figure 1-4.
Figure 1-4
Now you can begin the cable connection.
Connect the steel wire of the quick installation cover to the hook of the quick installation port.
Connect the reserved integration cable of the wall mount bracket to the corresponding power
cable, video output cable, RS485 control cable, alarm input/output port(if necessary) of the
multiple-function composite cable of the quick installation speed dome. Paste the insulating tape
in the connection position to do the proper waterproof work. See Figure 1-5.
9
Figure 1-5
Note
The video port is covered the heat shrink tube of high shrinking ratio. After the video
connection, please heat the tube to make sure the video port is damp proof and water
proof.
1.2.3 Install the speed dome
After you complete the above steps, please pull the integration cable and multiple-function
composite cable to the wall mount bracket.
Line up the straight edge of the internal enclosure of the quick installation speed dome to the
straight edge of the quick installation port, and then push the speed dome to the bottom of the
port slowly. Use your hands to turn the three stainless screws of the quick installation port to the
groove of the internal enclosure of the quick installation speed dome. Turn the stainless screw of
straight edge of the quick installation port to the Ф6.5 hole of the straight edge of the internal
enclosure of the quick installation speed dome. Use the inner hex tool to fix these three stainless
screws. Now you have completed the installation. See Figure 1-6.
10
Figure 1-6
Important
After the installation, please make sure:



The three stainless screws of the quick installation port are firmly secure.
The quick installation speed dome is fixed.
The speed dome is straight.
 The steel wire connection is firm.
After your installation, the interface is shown as in Figure 1-7.
Figure 1-7
11
1.3 Initial Setup
The default setup is:
 Address: 1

Baud rate: 9600
1.4 Dial Switch Setup
The two dial switches of the speed dome are SW1 and SW2. These are to specify the sp eed
dome parameter such as protocol, baud rate, address and etc. When the button is ON, it is 1. In
the SW1 and SW2, 1 is the lowest bit and the 8 is the highest bit. See Figure 1-8.
Please note this series speed dome cans automatically recognize the DH-SD, PELCO-D.
PELCO-P. Usually you do not need to set the protocol.
Figure 1-8
1.4.1 Communication protocol and Baud rate
Please refer to the protocol sheets for detailed information.
Protocol
Baud rate
1
2
3
4
5
6
Parity
7
1
2
3
4
Communication Protocol
OFF
OFF
OFF
OFF
DH-SD ( Compatible
8
with
industrial standard protocol)
ON
OFF
OFF
OFF
PELCO-D
OFF
ON
OFF
OFF
PELCO-P
X
X
X
X
Reserved
Please refer to the baud rate sheet for detailed information.
5
6
Baud Rate
OFF
OFF
9600bps
ON
OFF
4800bps
12
China
OFF
ON
2400bps
ON
ON
1200bps
Please refer to the parity setup sheet for detailed information.
7
8
Parity
OFF
OFF
NONE
ON
OFF
EVEN
OFF
ON
ODD
ON
ON
NONE
1.4.2 Address Setup
The speed dome address setup interface is shown as below. See Figure 1-9.
Figure 1-9
The encode mode adopts binary system. 1 to 8 is valid bit. The highest address bit is 255. You
can refer to the following sheet for more information.
Address 1
2
3
4
5
6
7
8
1
1
2
3
4
5
6
7
8
……
254
255
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
…………………………………………………………………
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
13
2 BRACKET DIMENSIONS
2.1 Wall mount bracket
The wall mount bracket dimensions are shown as below. See Figure 2-1.
Figure 2-1
2.2 Hanging mount bracket (Multiple Lengths)
The hanging mount bracket is shown as below. See Figure 2-2.
The bracket length setup values are:


200mm
300mm
 500mm
You just need to replace the
connection pole.
Figure 2-2
14
2.3 Corner mount bracket
The corner mount bracket is shown as below. See Figure 2-3.
Figure 2-3
2.4 Pole mount bracket
The corner mount bracket is shown as below. See Figure 2-4.
Figure 2-4
15
3 WALL MOUNT BRACKET INSTALLATION
3.1 Component Installation
Wall mount bracket is shown as below. See Figure 3-1.
Figure 3-1
3.2 Installation
3.2.1 Installation Requirements
The wall mount speed dome can be installed in the hard construction wall in the indoor or
outdoor environments. Before the installation, please make sure:


The wall is thick enough to install the expansion bolt.
The wall can at least sustain the 4x weight of the speed dome.
3.2.2 Installation Steps
Please draw four holes position in the wall according to the hole of the bottom of the wall mount
bracket. Then you can dig four holes and insert the expansion bolts (not provided). Use four hex
bolts and flat washer to fix the bracket in the expansion bolts. See Figure 3-2.
Installation
Hole
Figure 3-2
16
Install the speed dome in the bracket. See Figure 3-3.
Figure 3-3
Please refer to chapter 1.2 for detailed installation information.
17
4 HANG MOUNT BRACKET INSTALLATION
4.1 Component Installation
Hang mount bracket and its components are shown as below. See Figure 4-1.
Figure 4-1
4.2 Installation
4.2.1 Installation Requirements
The hang mount speed dome can be installed in the hard construction wall in the indoor or
outdoor environments. Before the installation, please make sure:


The wall is thick enough to install the expansion bolt.
The wall can at least sustain the 4x weight of the speed dome.
4.2.2 Installation Steps
Loosen the M4 bolt in the flange side to separate the flange and steeve. Pull the integration cable
through the airproof slot of the bottom of the flange and then connect to the centre hole of the
flange. Please secure the flange in the ceiling. See Figure 4-3. Please note, if the speed dome
is installed in the outdoor environments, you need to paste the silica gel on the surface of
the flange and the surface and the cable exit.
Silica gel
Connect to flange
Figure 4-2
Figure 4-3
18
Pull the cable through the steeve and then secure the steeve to the flange. Fix the M4 bolt.
Please note, if the speed dome is installed in the outdoor environments, you need to paste
enough Teflon tape at the top screw thread of the steeve and then turn the steeve to the flange
firmly. Please paste the silica gel on the steeve connection surface to do the waterproof work.
See Figure 4-4.
Teflon tape
M4 bolt
Silica gel
Figure 4-4
Please draw four holes position in the wall according to the hole of the bottom of the wall mount
bracket. Then you can dig four holes and insert the expansion bolts (not provided). . Use four
hex but and flat washer to fix the bracket in the expansion bolts. See Figure 4-5.
Long pole
Without pole
Figure 4-5
Please refer to chapter 1.2 for detailed installation information.
19
5 CORNER MOUNT BRACKET INSTALLATION
5.1 Component Installation
Corner mount bracket and its components are shown as below. See Figure 5-1.
Figure 5-1
5.2 Installation
5.2.1 Installation Requirements
The corner mount speed dome can be installed in the hard construction wall in the indoor or
outdoor environments where there is a 90 degrees angle. Before the installation, please make
sure:
 The wall is thick enough to install the expansion bolt.

The wall can at least sustain the 4x weight of the speed dome.
5.2.2 Installation Steps
Please draw four holes position in the wall according to the holes of the corner installation
accessories. See Figure 5-2.
Installation hole
Figure 5-2
Then you can dig four holes and insert the M8 expansion bolts. Pull the power cable,
video/control cable and the alarm cable through the centre hole of the bottom of the corner
bracket, the waterproof adhesive, and the centre of the bracket. Please reserve the enough cable
connection length and then use the M8 expansion bolt to secure the corer mount bracket chassis
on the wall. See Figure 5-3.
20
Figure 5-3
Please refer to chapter 1.2 for detailed installation information.
21
6 POLE MOUNT BRACKET INSTALLATION
Pole mount bracket and its components are shown as below. See Figure 6-1.
Figure 6-1
6.1 Installation
6.1.1 Installation Requirements
The corner mount speed dome can be installed in the hard construction wall in the indoor or
outdoor environments.
Before the installation, please make sure the pole bracket can sustain the 4X weight of the speed
dome.
The diameter of the pole structure shall comply with the installation dimension of the clamp.
Default factory clamp is six inches for the column of φ130-152mm. It can work with the pole
installation bracket. You can adjust the diameter and the value (clamp specification) is : φ5982mm、φ84-108mm、φ103-127mm, φ130-152mm、φ155-178mm、φ180-203mm,φ194-216mm.
The clamp is shown as in Figure 6-2.
Figure 6-2
For special dimensions, please contact us for more information.
Please refer to Figure 6-3 to install clamp and pole bracket.
Pull the cable out of the pole accessories and then use clamp to fix the pole accessories to the
pole. Finally, you can use glass cement to the output hole to secure waterproof.
22
Clamp and pole bracket connection
Pole bracket and the pole connection
Figure 6-3
After you installed bracket and external cover, loosen the captive screws and open the panel, pull
the power cable through the hanging bracket and then fix the hanging bracket to the wall. Please
pay attention to the waterproof between the bracket and the wall. See Figure 6-4.
Figure 6-4
Please refer to chapter 1.2 for detailed installation information.
23
7 APPENDIX Ⅰ THUNDER PROOF AND SURGE
PROTECTION
This series speed dome adopts TVS lighting protection technology. It can effectively prevent
damages from various pulse signals below 1500W, such as sudden lighting and surge. While
maintaining your local electrical safety code, you still need to take necessary precaution
measures when installing the speed dome in the outdoor environment.

The distance between the signal transmission cable and high-voltage device (or high-voltage
cable) shall be at least 50 meters.


Outdoor cable layout shall go under the penthouse if possible.
For vast land, please use sealing steel tube under the land to implement cable layout and

connects one point to the earth. Open floor cable layout is forbidden.
In area of strong thunderstorm hit or near high sensitive voltage (such as near high-voltage


transformer substation), you need to install additional high-power thunder protection device
or lightning rod.
The thunder protection and earth of the outdoor device and cable shall be considered in the
building whole thunder protection and conform to your local national or industry standard.
System shall adopt equal-potential wiring. The earth device shall meet anti-jamming and at
the same time conforms to your local electrical safety code. The earth device shall not short
circuit to N (neutral) line of high voltage power grid or mixed with other wires. When connect
the system to the earth alone, the earth resistance shall not be more than 4 Ω and earth
cable cross-sectional area shall below 25 mm2. See Figure 7-1.
Figure 7-1
24
8 APPENDIX Ⅱ ABOUT RS485 BUS
8.1 RS485 Bus Main Feature
RS485 is semi duplex communication cable of impedance 120Ω. Its max load amount is 32
effective loads (including main control device and devices to be charged).
8.2 RS485 Bus Transmission Distance
When we take 0.56mm (24AWG) twisted-pair as communication cable, the max transmission
distance (theoretically) are listed below (according to different baud rates).
Baud Rate Max Distance
2400 BPS 1800M
4800 BPS 1200M
9600 BPS 800M
In the following situations, the max transmission distance shall become short er accordingly:
 The communication cable is a little bit thin;
 The surrounding environment has strong electromagnetic interference;
 There are too much devices connected to the RS485 bus;
And vice versa, the max transmission distance shall become longer.
8.3 The Problem in Practical Use
In practical usage, we usually adopt star type connection. The terminal resistance shall connect
to the furthest two devices (Such as device 1# and device 15# in Figure 8-1. But this connection
way does not conform to RS485 Bus standard. When the distances between devices are too
long, the signal reflection occurs and anti-jamming decreases, thus the signal reliability becomes
very low. You can see speed dome is not under control or speed dome is running automatically
and cannot stop.
Figure 8-1
In this situation, we recommend RS485 distributor. This device can turn star type connection into
the connection that conforms to RS485 bus industry standard, which can avoid the above
mentioned problems and enhance communication reliability. See Figure 8-2.
25
Figure 8-2
8.4 RS485 Bus FAQ
Phenomenon
Speed dome
can run selfdiagnosis but I
can not control
it.
I can control
the speed
dome but is not
smooth
Possible Reasons
 Host address(baud rate) and
speed dome address(baud rate)
are not match;
 Positive and negative end of
RS485 Bus are misconnected;
 Connection cable is loose;
 RS485 Bus connection are cut
off;
 RS485 Bus connection are not
good;
 One RS485 bus is off;
 The distance between host and
speed dome is too far;
 Parallel connected too much
speed domes.
Solution
 Modify host or speed dome setup ;
 Switch RS485 positive end and
negative end;
 Fix connection cable firmly;
 Replace RS485 Bus.




Connect RS 485 Bus again;
Replace RS485 Bus;
Add terminal matching resistance;
Add RS485 distributor.
Note

This manual is for reference only. Slight difference may be found in the user
interface.

All the designs and software here are subject to change without prior written
notice.

If there is any uncertainty or controversy, please refer to the final explanation of us.

Please visit our website or contact your local service engineer for more
information.
26
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising