Bul. 140G/140MG
DIR 1000719R0805 Version 01 - 140G-_-EXS3, 140G-_-EXS4
Front spread terminal for 140G-G, 140G-H, 140G-I, 140G-J
Terminali anteriori divaricati
Vorderseitige verbreiterte Anschlüsse
Prises avant épanouies
Terminales frontales separadores
Installation - Installazione - Instalación
Instalação - -
WARNING: To prevent electrical shock, disconnect from power source before installing or servicing. Install in suitable enclosure. Keep free from contaminants.
(Follow NFPA70E requirements).
AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
(Seguire i requisiti NFPA70E).
WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur
Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden. (Befolgen
Sie die Anforderungen nach NFPA70E).
AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée.
Protéger le produit contre les environnements agressifs. (Vous devez respecter la norme NFPA70E).
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.
Manténgalo libre de contaminantes. (Cumpla con los requisitos NFPA70E).
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de contaminantes. (Cumpra as exigências da norma NFPA70E).
警告：感電事故防止のため、取付けまたは修理の際は電源から取り外してく
ださい。適切なケース内に取付けてください。また、汚染物質がないことを
確認してください。（ NFPA70E の要件に従ってください）
警告：为了防止触电，在安装或维修之前必须先切断电源。安装在合适的设备
物
140G-G
1
CLACK
140G-I
Terminals
3p
140G-G
4p
3p
140G-H
4p
140G-I
3p
4p
3p
140G-J
4p
/
/
/
/
/
/ x1 x1
/
/
/
/
/
/
/ x1
/
/
/
/
/
/
/ x1
/
/
/
/
/
/ x1
/
/
/
/
/
/
/ x1 x1 x1 x1 x1 x1
/
/ x1 x1
/ x1
/ x1
/
/
/ x1
/
/ x1
/ x1
/ x1
/
/ x1
/ x1
/
/
/ x1 x1 x1 x1 x1
/
/ x1 x1
DIR 1000719R0805 Version 01 x2 x3 x2 x3 x2 x3 x2 x3
140G-H
1
CLACK
Phase barriers Insulator
/
/ x1 x1
/
/ x1 x1
140G-J
Screw
LENGTH dia.
6.5 mm (0.26") 2.9
/
/ x2 x2
/
/ x2 x2
1
3
5
3
1
2
1
2
3
2
1
- If present
- Se presente
- Falls vorhanden
- Si présent
- Si lo hay
140G-H, 140G-I, 140G-J 3p 4
OK
NO
2
3
1
CH 5
140G-H 53 lb-in/6 Nm
140G-I, 140GJ 71 lb-in/8 Nm
CH 6
4
G&I 140G-G-PB3H
H&J 140G-H-PB3H
3p 6
2
140G-G 3p
OK
NO
CH 5
53 lb-in
6 Nm
4
2
OK
NO
4p
CH 5
140G-G, 140G-H 53 lb-in/6 Nm
4
140G-I, 140GJ 71 lb-in/8 Nm
CH 6
G&I 140G-G-PB4H
H&J 140G-H-PB4H
4p
DIR 1000719R0805 Version 01
1
1
1
2
2
- If present
- Se presente
- Falls vorhanden
- Si présent
- Si lo hay
(2)
1
1
2
1
- If present
- Se presente
- Falls vorhanden
- Si présent
- Si lo hay
7 140G-H, 140G-J 3p
8
140G-H 140G-J
A 3.24"/82.5 mm 3.05"/77.5 mm
B 6.49"/165 mm 6.10"/155 mm
C 11.1"/282 mm 12.83"/326 mm
X
Ue > 440V
B
Y
A dia. 0.10"/ø 2.6 mm
X
1
Y
140G-H, 140G-J 3p
2
LENGTH dia.
6.5 mm (0.26") 2.9
2
DIR 1000719R0805 Version 01
(3)
9
140G-H 140G-J
A 3.24"/82.5 mm 3.15"/80 mm
B 7.68"/195 mm 7.68"/195 mm
C 11.1"/282 mm 12.83"/326 mm
X
Ue > 440V
B
Y
A dia. 0.10"/ø 2.6 mm
X
1
Y
140G-H, 140G-J 4p
2
LE N GT H
6. 5 mm (0. 26" ) di a.
2. 9
2
Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Rockwell Automation maintains current product environmental compliance information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/ sustainability-ethics/product-environmental-compliance.page
Publication 140G-IN091B-MU-P - September 2015 DIR 1000719R0805 Version 01 (L8101) - B0301
Copyright © 2015 Rockwell Automation, Inc. All Rights Reserved. Printed in Italy.
