Cytron Technologies SHIELD-LIPO User Manual
Cytron Technologies SHIELD-LIPO is a LiPo Power Shield that is compatible with various Arduino boards. It allows you to power your projects with a 3.7V 1300mAH LiPo battery, providing at least 500mA current and peaking at 1A. The SHIELD-LIPO includes an integrated charger with a charging current of 500mA, and can be charged from either the onboard USB port or the USB port on the Arduino. It also has low battery and undervoltage protection features, with a low battery indicator threshold of 3.3V and a cutout voltage of 2.4V.
Advertisement
Advertisement
ROBOT . HEAD to TOE
Product User’s Manual – SHIELD-LIPO
SHIELD-LIPO
Cytron LiPo Power Shield
User's Manual
V1.0
January 2016
Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved
1
4.
5.
6.
7.
1.
2.
3.
Index
ROBOT . HEAD to TOE
Product User’s Manual – SHIELD-LIPO
6
8
12
13
3
4
5
Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved
2
ROBOT . HEAD to TOE
Product User’s Manual – SHIELD-LIPO
1. INTRODUCTION AND OVERVIEW
Cytron LiPo Power Shield (SHIELD-LIPO) is an Arduino compatible shield which is compatible with Arduino UNO , Arduino Duemilanove , Arduino Mega , Arduino Leonardo and possibly other pin compatible main boards. You can take your Arduino anywhere you wish with this LiPo Power Shield.
Cytron LiPo Power Shield has stackable side headers which allows more Arduino shield to be stacked on top of it. You can stack shields on top, or stack the Shield LiPo on top. Please note that the Shield LiPo does not pass through the ICSP headers (the battery is in the way) so if your stack shield uses ICSP for data transfer (like the Ethernet Shield), you'll need to stack the Shield LiPo above it.
This Shiels-LiPo can provide at least 500mA current, and peak at 1A. It has undervoltage protection to avoid damage to battery.
Features:
● Output Voltage: 5V
● Output current: 1A
● Powered by 3.7V 1300mAH LiPo battery.
● Integrated charger, Charging current: 500mA.
● Can be charged from the onboard USB port or the USB port on the Arduino.
● Low battery indicator, Threshold voltage : 3.3V.
● Undervoltage protection, Cutout voltage: 2.4V.
● Stackable side headers.
Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved
3
2. PACKING LIST
ROBOT . HEAD to TOE
Product User’s Manual – SHIELD-LIPO
1. 1 x SHIELD-LIPO
Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved
4
3. DIMENSION
Dimensions (mm)
ROBOT . HEAD to TOE
Product User’s Manual – SHIELD-LIPO
Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved
5
4. BOARD LAYOUT
ROBOT . HEAD to TOE
Product User’s Manual – SHIELD-LIPO
Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved
6
ROBOT . HEAD to TOE
Product User’s Manual – SHIELD-LIPO
1. Stackable Digital I/O Headers
Digital I/O pins stacked to the Arduino main board.
2. Low power LED indicator
Indicator to show that LiPo Battery are below than 3.3V
3. Power indicator LED (Green)
Indicator to shows that power is supplied to Cytron LiPo Power Shield
4 .
Full power LED indicator
Indicator to show that LiPo Battery are fully charged
5. Charge LED indicator
Indicator to show that LiPo Battery are charging.
6. Main Board reset button
Arduino main board will require around 30ms to ready after reset.
7. Power switch
Switch to On/Off the battery.
8. USB port
This USB port is for charging. You can use USB Micro B cable to charge the battery
9. LiPo Battery
Powered by 3.7V 1300mAH LiPo battery.
10. Vbatt Solder Jumper
Solder the pads together for monitoring battery voltage.
Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved
7
ROBOT . HEAD to TOE
Product User’s Manual – SHIELD-LIPO
5. HARDWARE
This section shows the example of using SHIELD-LIPO with Arduino UNO / CT-UNO as the main controller.
5.1 Way to Stack the shield on Arduino board
Figure below shows that the SHIELD-LiPo is stacked on the CT-UNO. Please ensure that the pins alignment is correct.You can stack shields on top, or stack the Shield LiPo on top.
Please note that the Shield LiPo does not pass through the ICSP headers (the battery is in the way) so if your stack shield uses ICSP for data transfer (like the Ethernet Shield), you'll need to stack the Shield LiPo above it like shown in figure below.
Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved
8
ROBOT . HEAD to TOE
Product User’s Manual – SHIELD-LIPO
5.2 Charging Method for SHIELD-LIPO
You can charge the LiPo battery either from the onboard USB port or the USB port on the
Arduino. When the battery is charged, “Charge” LED will ON, When the battery is fully charge, “Full” will ON
1) If charge using onboard USB port , power switch can be either in ON or OFF state.
Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved
9
ROBOT . HEAD to TOE
Product User’s Manual – SHIELD-LIPO
2) While if you are using Arduino USB port , you have to switch off the SHIELD LiPo. If it is ON, the battery will not charge.
Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved
10
ROBOT . HEAD to TOE
Product User’s Manual – SHIELD-LIPO
5.3 Monitoring Battery Voltage.
The battery voltage level can be monitor using Arduino Board. At the back of shield there is
VBATT Solder Jumper. You can solder it together like shown in the figure below. Then you can use Arduino IDE serial monitor, to monitor the battery voltage.
Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved
11
ROBOT . HEAD to TOE
Product User’s Manual – SHIELD-LIPO
6. SOFTWARE
You can use Arduino IDE Serial monitor to check the battery voltage. Example of coding:
Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved
12
ROBOT . HEAD to TOE
Product User’s Manual – SHIELD-LIPO
7. WARRANTY
●
●
●
●
Product warranty is valid for 12 months.
Warranty only applies to manufacturing defect.
Damaged caused by misuse is not covered under warranty
Warranty does not cover freight cost for both ways.
Prepared by:
Cytron Technologies Sdn. Bhd.
No. 16, Jalan Industri Ringan Permatang Tinggi 2,
Kawasan Industri Ringan Permatang Tinggi,
14100 Simpang Ampat,
Penang, Malaysia.
Tel: +604 - 504 1878
Fax: +604 -504 0138
URL: www.cytron.com.my
Email: [email protected]
Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved
13

Public link updated
The public link to your chat has been updated.
Advertisement