Brilliant
Wonders
LED WATERFALLS
TM
Wireless Touch LED RGB Remote Controller
25650-100 Series
OPERATION & INSTALLATION QUICK REFERENCE
WARNINGS AND IMPORTANT SAFETY PRECAUTIONS
Be sure that the electrical system prior to installation conforms to all local codes and ordinances. A licensed or certified electrician must install the electrical system to insure that it follows all of the requirements of the National Electric Code (NEC). The electrician may need to consult the local building inspector for code interpretation before installing the 25650-100 wireless controller.
IMPORTANT NOTICE
Attention Installer: This manual contains important information about the installation, operation, and safe use of this product. This information should be given to the owner and/or operator of this equipment. When installing and using this electrical equipment, basic safety precautions should always be observed.
Read all safety precautions and important instructions before attempting any electrical wiring. Ensure that all power has been turned off at the power source. Failure to follow safety warnings and instructions can result in severe injury, death, or property damage.
CMP recommends installation to be performed by a licensed professional.
INTRODUCTION
Thank you for choosing the CMP 25650-100 series controller.
If you haven’t already done so, please take a moment to read our safety information. To fully enjoy the features of this controller, please read the entire manual before operating. Following these safety requirements should prevent any damage to your new controller.
1. PERFORMANCE PARAMETERS
CONTROLLER
• Power input: 12 Volt DC
• Max Current: 5A x 3CH Max 15A
• Maximum load power: 180 Watts
• Change Mode: 32
• Scale Levels: 65536 steps/RGB
(16Bits/CH)
• Control Function: 8 touch buttons
• Operating temp: -30°C to 55°C
• Dimension: L8.3 in. x W1.6 in. x H1.2 in.
• Weight(net): 180g
REMOTE
• Power: Rechargeable 5 Volt DC built in Lithium battery
• Working Current: 30mA
• Working Frequency: 2.4 GHZ
• Battery Capacity: 1000mAh
• Charge Time: <4 hours
• Normal Usage Time: 30 days
• Number of charge cycles: 500
• Operating range: up to 90 feet
(dependent on environment)
• Operating temp: -30°C to 55°C
• Dimension: 5.7”L x 2.2”W x 0.9”H
• Weight(net): 200g
2. KEY FEATURES
The remote control has 18 function buttons and 1 full-color touch circle. The controller has 8 touch buttons.
HOW TO PAIR THE CONTROLLER WITH THE REMOTE
Press the “ON/OFF” key on the controller until you hear the “BEEP” sound, then press the “1” key on the remote to activate the connection between the controller and remote control. Press the “2” key to cancel the connection set successfully when heard takq
Controller sign Remote control sign Button Description
MODE
SPEED
BRT
PAUSE
MODE
SPEED
BRT
ON/OFF ON/OFF: Turn on/off the Controller.
PAUSE PAUSE
Press once to stay at current color
Press again to resume color changing
Press this button in 3 seconds, and the buzzer can be turned on or off
MODE+
MODE-
SPEED+
SPEED-
Press the keys to select next mode or back to previous mode.
SPEED+ / SPEED-
Press the keys to quicken and slow color change speed
BRT+
BRT-
Full Color
Touch
Circle
Nine DIY
Keys
BRT+/BRT-
Press the keys to increase or decrease brightness, keep pressing to adjust brightness continuously
When touching the full-color circle, LED lights will show the same color as the circle.
Press a key for 3 seconds and the controller will save the current function mode automatically. Save up to 9 modes and save repeatedly as well. Press the “PLAY” key to cycle all saved modes. (this only plays the dynamic effects, static effects will be skipped automatically)
3. LIGHT MODES
No.
9
10
7
8
5
6
3
4
1
2
11
12
13
14
15
16
Mode
Static red
Static green
Static blue
Static yellow
Static purple
Static cyan
Static white
RGB skipping
7 colors skipping
White strobe
7 colors strobe
Red fade out and fade in
Green fade out and fade in
Blue Fade out and fade in
Yellow fade out and fade in
Purple fade out and fade in
Description brightness adjustable brightness adjustable brightness adjustable brightness adjustable brightness adjustable brightness adjustable brightness adjustable speed/brightness adjustable speed/brightness adjustable speed/brightness adjustable speed/brightness adjustable speed/brightness adjustable speed/brightness adjustable speed/brightness adjustable speed/brightness adjustable speed/brightness adjustable
3
No.
29
30
31
32
25
26
27
28
21
22
23
24
17
18
19
20
Mode
Cyan fade out and fade in
White fade out and fade in
RGB fade out and fade in
Red Green color smooth
Red Blue color smooth
Green Blue color smooth
Red Yellow color smooth
Green Cyan color smooth
Blue purple color smooth
Green Yellow color smooth
Blue Cyan color smooth
Red Purple color smooth
Blue White color smooth
Yellow Purple Cyan color smooth
RGB color smooth full color smooth y
Description speed/brightness adjustable speed/brightness adjustable speed/brightness adjustable speed/brightness adjustable speed/brightness adjustable speed/brightness adjustable speed/brightness adjustable speed/brightness adjustable speed/brightness adjustable speed/brightness adjustable speed/brightness adjustable speed/brightness adjustable speed/brightness adjustable speed/brightness adjustable speed/brightness adjustable speed/brightness adjustable
3. INSTALLATION AND WIRING DIAGRAM
Connected to RGB module as an example
CLASS 2
POWER
SUPPLY
AC
L N
DC
DC12V
R G
B
R G
B
DC12V
R G
B
R G
B
R G
B
R G
B
R G
B
R G
B
Note: Ensure all wire connections and polarities are correct before applying power.
R G R G R G R G
CONTROLLER MOUNTING
You must provide the controller enclosure a. The enclosure or junction box must be installed per the National Electric
Code (NEC) requirements as well as comply with any local codes and regulations b. All wire used from the controller box to luminaire must be in conduit.
c. Min size of controller box must be 9" x 2" x 1.5".
d. The enclosure must be non-metallic(plastic) to ensure adequate RF signals are achieved. e. For product longevity, ensure proper ventilation where both the controller and power supply may be mounted inside the same enclosure in elevated outdoor temperatures.
DO NOT INSTALL ANY OTHER ITEM
INSIDE CONTROLLER ENCLOSURE.
State listed Class 2 Power Supply and Listed outdoor junction box will have to be purchased and installed.
CMP Plastic Outdoor Box for Controller Only
25650-100-210
4. CHARGING METHODS
1. When charging, connect the USB cable to the mobile charger or a computer with USB interface. The remote control must be turned on to charge.
2. The blue indicator light flickers while charging, and will turn green when fully charged
3. No memory effect in the lithium battery of the remote control. Follow the standard charging procedure even for the first three charges. There is no need to over charge.
4. The red indicator light flickers when the battery is low and needs to be charged soon. Charging in low battery will effect battery life.
5. REPLACEMENT PARTS & DIMENSIONS GUIDE
COLORWHEEL REMOTE
10mm
25650-100-300
25650-100-000
145mm
LED CONTROLLER
15mm
DESCRIPTION
REMOTE & CONTROLLER
COLORWHEEL REMOTE
CONTROLLER
10mm
211mm
203mm
® everything matters.
10mm
15mm
10mm
145mm www.c-m-p.com
©2013 Custom Molded Products sb0913
