V170 SBC - Welcome to Winmate Distributor Portal

V170 SBC - Welcome to Winmate Distributor Portal
V170 SBC
Mini-ITX Fanless SBC w/VIA Eden,
VIA CX700 Chipset, VGA, LCD, Giga
Ethernet and PCI Interface.
User Manual Version 1.0
FCC Statement
This device complies with part 15 FCC rules. Operation is subject to
the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a class "a"
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at him
own expense.
z
z
V170 SBC User Manual
I
Copyright Notice
Copyright © 2007 Winmate Technology Inc., ALL RIGHTS RESERVED. No part of
this document may be reproduced, copied, translated, or transmitted in any form or by
any means, electronic or mechanical, for any purpose, without the prior written
permission of the original manufacturer.
Trademark Acknowledgement
Brand and product names are trademarks or registered trademarks of their respective
owners.
Disclaimer
Winmate Communication Inc. reserves the right to make changes, without notice, to
any product, including circuits and/or software described or contained in this manual
in order to improve design and/or performance. Winmate Communication assumes no
responsibility or liability for the use of the described product(s), conveys no license or
title under any patent, copyright, or masks work rights to these products, and makes
no representations or warranties that these products are free from patent, copyright, or
mask work right infringement, unless otherwise specified. Applications that are
described in this manual are for illustration purposes only. Winmate Communication
Inc. makes no representation or warranty that such application will be suitable for the
specified use without further testing or modification.
Warranty
Winmate warrants that each of its products will be free from material and
workmanship defects for a period of one year from the invoice date. If the customer
discovers a defect, Winmate will, at its option, repair or replace the defective product
at no charge to the customer, provided it is returned during the warranty period of one
year, with transportation charges prepaid. The returned product must be properly
packaged in its original packaging to obtain warranty service.
If the serial number and the product shipping data differ by over 30 days, the
in-warranty service will be made according to the shipping date. In the serial numbers
the third and fourth two digits give the year of manufacture, and the fifth digit means
the month (e. g., with A for October, B for November and C for December).
For example, the serial number 1W07Axxxxxxxx means October of year 2007.
V170 SBC User Manual
II
Packing List
Before using this Motherboard, please make sure that all the items listed below are
present in your package:
¾ V170 Motherboard
¾ User Manual
¾ User’s Manual & Driver CD
¾ 1 x SATA HDD Cable
¾ 1 x SATA HDD Power Cable
¾ 1 x USB cable
¾ 1 x COM Port cable
If any of these items are missing or damaged, contact your distributor or sales
representative immediately.
Customer Service
We provide service guide for any problem as follow steps:
Step1: visit the website at http://www.winmate.com/ to find the update information
about the product.
Step2, contact with your distributor, sales representative, or our customer service
center for technical support if you need additional assistance. You may have the
following information ready before you call:
¾ Product serial number
¾ Peripheral attachments
¾ Software (OS, version, application software, etc.)
¾ Description of complete problem
¾ The exact wording of any error messages
In addition, free technical support is available from our engineers every business day.
We are always ready to give advice on application requirements or specific
information on the installation and operation of any of our products. Please do not
hesitate to call or e-mail us.
V170 SBC User Manual
III
Safety Precautions
‹
Warning!
Always completely disconnect the power cord from your chassis
whenever you work with the hardware. Do not make connections
while the power is on. Sensitive electronic components can be
damaged by sudden power surges. Only experienced electronic
personnel should open the PC chassis.
‹
Caution!
Always ground yourself to remove any static charge before
touching the CPU card. Modern electronic devices are very
sensitive to static electric charges. As a safety precaution, use a
grounding wrist strap at all times. Place all electronic components
in a static-dissipative surface or static-shielded bag when they are
not in the chassis.
V170 SBC User Manual
IV
Safety and Warranty
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Please read these safety instructions carefully.
Please keep this user's manual for later reference.
Please disconnect this equipment from any AC outlet before cleaning. Do not use
liquid or spray detergents for cleaning. Use a damp cloth.
For plug gable equipment, the power outlet must be installed near the equipment
and must be easily accessible.
Keep this equipment away from humidity.
Put this equipment on a reliable surface during installation. Dropping it or letting
it fall could cause damage.
The openings on the enclosure are for air convection. Protect the equipment from
overheating. DO NOT COVER THE OPENINGS.
Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
All cautions and warnings on the equipment should be noted.
If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient over-voltage.
Never pour any liquid into an opening. This could cause fire or electrical shock.
Never open the equipment. For safety reasons, only qualified service personnel
should open the equipment.
If any of the following situations arises, get the equipment checked by service
personnel:
A. The power cord or plug is damaged.
B. Liquid has penetrated into the equipment.
C. The equipment has been exposed to moisture.
D. The equipment does not work well, or you cannot get it to work according to
the user’s manual.
E. The equipment has been dropped and damaged.
F. The equipment has obvious signs of breakage.
Do not leave this equipment in an uncontrolled environment where the storage
temperature is below -10°C (-14°F) or above 55°C (131°F). It may damage the
equipment.
V170 SBC User Manual
V
Revision History
Version
Date
0.1
2007.06.12
0.2
2007.07.18
1.0
2008.02.20
V170 SBC User Manual
Note
9 Initial Release
9 Feature, Spec Format,
Function Block, Board
Dimension revised
9 Package List Modified
9 BIOS Menu Modified
9 Add Panel ID List
9 Add 12V DC-IN and
24V DC-IN Option
VI
Author
Shawn Kuo
Shawn Kuo
Shawn Kuo
Contents
CHAPTER 1
GENERAL INFORMATION .........................................................2
1.1
INTRODUCTION.......................................................................................................................2
1.2
FEATURES ...............................................................................................................................2
1.3
MOTHERBOARD SPECIFICATIONS ...........................................................................................3
1.4
FUNCTION BLOCK ..................................................................................................................4
1.5
BOARD DIMENSIONS ...............................................................................................................5
CHAPTER 2
INSTALLATIONS ...........................................................................7
2.1
MEMORY MODULE INSTALLATION .........................................................................................7
2.2
I/O EQUIPMENT INSTALLATION ..............................................................................................8
2.3
JUMPERS AND CONNECTORS...................................................................................................9
2.4
JUMPER SETTING ..................................................................................................................10
2.5
CONNECTORS AND PIN ASSIGNMENT....................................................................................12
CHAPTER 3
BIOS SETUP ..................................................................................26
3.1
STARTING SETUP ..................................................................................................................26
3.2
AWARD BIOS SETUP ............................................................................................................27
3.3
STANDARD CMOS FEATURES ..............................................................................................29
3.4
ADVANCED BIOS FEATURES ................................................................................................32
3.5
ADVANCED CHIPSET FEATURES ............................................................................................36
3.6
INTEGRATED PERIPHERALS...................................................................................................39
3.7
POWER MANAGEMENT SETUP ..............................................................................................43
3.8
PNP/PCI CONFIGURATIONS ..................................................................................................46
3.9
PC HEALTH STATUS..............................................................................................................47
3.10
FREQUENCY/VOLTAGE CONTROL .........................................................................................48
3.11
LOAD FAIL-SAFE DEFAULTS .................................................................................................49
3.12
LOAD OPTIMIZED DEFAULTS ................................................................................................50
3.13
SET SUPERVISOR/USER PASSWORD ......................................................................................51
3.14
SAVE & EXIT SETUP .............................................................................................................52
3.15
EXIT WITHOUT SAVING ........................................................................................................53
CHAPTER 4
CHIPSET DRIVER INSTALLATION ........................................55
4.1
INTRODUCTION.....................................................................................................................55
4.2
INSTALLATION OF ETHERNET DRIVER ..................................................................................55
4.3
FURTHER INFORMATION .......................................................................................................57
CHAPTER 5
ETHERNET DRIVER INSTALLATION ...................................59
V170 SBC User Manual
VII
5.1
INTRODUCTION.....................................................................................................................59
5.2
INSTALLATION OF ETHERNET DRIVER ..................................................................................59
5.3
FURTHER INFORMATION .......................................................................................................61
CHAPTER 6
VGA DRIVER INSTALLATION .................................................63
6.1
INTRODUCTION.....................................................................................................................63
6.2
INSTALLATION OF VGA DRIVER ...........................................................................................63
6.3
FURTHER INFORMATION .......................................................................................................64
CHAPTER 7
AUDIO DRIVER INSTALLATION ............................................66
7.1
INTRODUCTION.....................................................................................................................66
7.2
INSTALLATION OF AUDIO DRIVER.........................................................................................66
7.3
FURTHER INFORMATION .......................................................................................................70
V170 SBC User Manual
VIII
CHAPTER
General Information
1
This chapter includes V170 Motherboard background
information. The section includes:
z
Introduction
z
Features
z
Motherboard Specification
z
Function Block
z
Board Dimensions
V170 SBC User Manual
1
Chapter 1 General Information
1.1 Introduction
V170 is a high performance, high flexibility and low power motherboard with the
most advanced and complete all-in-one x86 system processor VIA CX700 chipset
which integrates from quadruple host data bus, DDR2 memory controller to Serial
ATA and USB ports for media processing. The VIA CX700 is based on a highly
sophisticated power efficient architecture which enables power dissipation only 3.5
watts maximum compensated with VIA C7 and fanless VIA Eden. V170 is designed
to satisfy most of the applications in the industrial computer market, such as POS,
KIOSK, Industrial Automation, Programmable Control System, and HMI. It also
could be an embedded system with multi-COM port interface, and on-board gigabits
Ethernet to meet the business and industrial applications.
1.2 Features
¾
¾
¾
¾
¾
¾
¾
¾
¾
Mini-ITX Form Factor (170mm x 170mm)
VIA Eden™ 1.0GHz by EBGA Type, Fanless Design
System Memory Up To 2GB DDR2 400/533 SDRAM
VIA CX700 Chipset
Integrated LVDS/VGA UniChrome Pro II 3D/2D Graphics Processor
VIA VT1708 High Definition Audio Controller
Gigabit LAN
2 x SATA, 1 x EIDE, 6 x USB 2.0, 1 x PCI, 1 x RJ45, 1 x VGA
4 x COM, 1 x FDD, 1 x IrDA, 1 x MODEM
V170 SBC User Manual
2
1.3 Motherboard Specifications
CPU Type
CPU Speed
CPU HT
Chipset
Cache
BIOS
VGA
LVDS
LAN
Memory Type
LPC I/O
Keyboard/Mouse
IDE
Sound
USB
Watchdog Timer:
Edge Connectors
On Board
Pin-Header
Connectors
VIA Eden™ by EBGA Type
1 GHz
400MHz
VIA CX700 w/ VIA UniChrome™ Pro Integrated Graphics Processor,
MPEG-2 Hardware Video Acceleration
256KB
4MB Award BIOS
Integrated VGA/LCD Controller, 2D/3D GUI engine,
Sharing memory architecture up to 64 MB
Dual Channel/2 x Single Channel LVDS, support panel resolution from
VGA through UXGA(1600 x 1200)
Realtek 8110SBL LAN Controller (10/100/1000 Mb)
Two DDR2 slots 240 pin Support up to 2GB DDR2 400 / 533 SDRAM
Winbond 83697HF supports IrDA x 1, Parallel x 1, Hardware monitoring,
FDC COM1 (RS-232) by Pin Header ,COM2 (RS-232/422/485) by D-sub
9p
PS/2 connectors (I/O) and on board pin header for internal use
44pin box header with 5V pin out, 2.0 pitch supports Ultra DMA 133
VIA HD Codec VT1708 Line out, Mic in with amplifier Phone jack x 2 and
internal Connector for line out or Pin Header
2 x USB (Pin Header), 4 x USB (connector)
256 level
2 x PS/2 connector for keyboard/mouse
1 x Gigabit LAN RJ-45 + 1 x dual USB stack connector
1 x Dual DB9 for COM 3 & COM 4
1 x Dual DB9 for COM 2 & VGA
1 x Audio Jack for Audio (Line-Out, Mic-In)
4 x USB ports
1 x DC-In Jack
1 x 44 pins box-header
2 x Serial ATA I / II 3.0 Gb/s
1 x 10pins pin-header for COM1(RS232)
1 x 10pins pin-header for USB 4/5(2x5)
1 x 4pins pin-header for CD_IN (1x4)
1 x 4pins pin-header for Speaker out (1x4)
1 x 40pins DF13 Connector for LVDS
1 x 4pins 12V/5V External Power Connector
1 x 10pins pin-header for Front Panel (2x5)
1 x 3pins pin-header for CPU Fan
1 x 3pins pin-header for System Fan
1 x 26P FPC Connector
1 x 26pins pin-header for parallel port support SPP/EPP/ECP
1 x 5pins pin-header for IrDA
1 x 10pins pin-header for DIO
1 x 16pins pin-header for MODEM
¾
Mechanical and
environmental:
¾
¾
¾
¾
V170 SBC User Manual
Dimensions (L x W): 170 mm x 170 mm (6.7” x 6.7”)
Power supply voltage: +12Volts DC-input(Optional +24 Volts DC-IN)
Power consumption (typical): 20W
Operating temperature:0~55ºC
Operating Humidity: 30~90% Relative humidity, non-condensing
3
1.4 Function Block
VCCP—EN5336
ATX Power
Connector
VIA Eden
Nano BGA2
+/- CPU CLK
CRT
LVDS
PS2 Port × 2
USB Port 0~5
HD VIA
VT1708
VCore
VID[0:5]
LTC3734
3.3V&5V--LTC3707
+12V--LTC3070
-12V--LTC1931
Clock Generator
ICS952906
+/- HCLK
ZDB ICS9P935
CX700(M)
DDRII DIMM × 2
Serial ATA × 2
IDE Primary
AUDIO AMP
RING&FAN
PCI BUS
&LAN CON
PCI SLOT 1
COM1 & COM2
LPT
LPC I/O W83679HF &FDD
&DIO LPC (BIOS)
LAN-RTL8110SBL
V170 SBC User Manual
DDR POWER
EN5366QI
Second I/O F81216D
COM3 & COM4
4
1.5 Board dimensions
Unit: mm
V170 SBC User Manual
5
CHAPTER
Installations
2
This chapter provides information on how to use the jumps
and connectors on V170 Motherboard.
The Sections include:
z
Memory Module Installation
z
I / O Equipment Installation
z
Setting the Jumpers
z
Connectors on V170 Motherboard
V170 SBC User Manual
6
Chapter 2 Installations
2.1 Memory Module Installation
V170 Motherboard provides two 240-pin DIMM slot. The socket supports up to
2GB DDR2 533 SDRAM. When installing the Memory device, please follow the
steps below:
Step.1. Locate the DIMM slot in the motherboard.
Step.2. Unlock a DIMM slot by pressing the retaining clips outward.
Step.3. Align a DIMM on the socket such that the notch on the DIMM matches
the break on the slot.
Step.4. Firmly insert the DIMM into the slot until the retaining clips snap back in
place and the DIMM is properly seated.
Available DDR2 SDRAM Configurations, refer to the table below for available
DDR2 SDRAM configurations on the mainboard.
Slot
Module Size
DIM1
64MB, 128MB, 256MB, 512MB, 1GB
DIM2
64MB, 128MB, 256MB, 512MB, 1GB
Maximum supported system memory
V170 SBC User Manual
7
Total
64MB-1GB
64MB-1GB
64MB-2GB
2.2 I/O Equipment Installation
2.2.1 PS/2 Keyboard and PS/2 Mouse
V170 Motherboard provides two connector supports PS/2 interface. In other cases,
especially in embedded applications, a mouse is not used. Therefore, the BIOS
standard setup menu allows you to select* “All, But Keyboard” under the “Halt On”.
This allows no-keyboard operation in embedded system applications without the
system halting under POST.
2.2.2 Audio function
The VIA HD capabilities are provided by a VIA HD Codec VT1708 chip supporting
digital audio outputs. The onboard VT1708 is a 20-bit DAC and 18-bit ADC
supporting full-duplex VIA HD 2.3 compatible stereo audio CODEC for multimedia,
including host/soft audio based designs. The audio interface includes two jacks:
microphone-in and line-out.
2.2.3 Serial COM ports
One RS-232 ports with 16C550 UART (or compatible) with 16-byte FIFO buffer.
Three optional COM ports support RS-232. When an optional touch-screen is ordered
with V170 Motherboard, serial com port can connect to a serial or an optional
touch-screen. One optional COM port supports RS232/422/485 choice through
jumper setting.
2.2.4 Ethernet interface
V170 Motherboard is equipped with Realtek RTL8110SBL chipset which is fully
compliant with the PCI 10/100/1000 Mbps Ethernet protocol compatible. It is
supported by major network operating systems. The Ethernet port provides a standard
RJ-45 jack.
2.2.5 USB ports
Four USB (Two is optional) devices may be connected to the system through an
adapter cable. Various adapters may come with USB ports. USB usually connect the
external system to the system. The USB ports support hot plug-in connection. Anyway,
you should install the device driver before you use the device.
2.2.6 External VGA
V170 Motherboard has one VGA port that can be connected to an external CRT/ LCD
monitor. Use VGA cable to connect to an external CRT / LCD monitor, and connect
the power cable to the outlet The VGA connector is a standard 15-pin D-SUB
connector
V170 SBC User Manual
8
2.3 Jumpers and Connectors
JBAT
FAN2 JP1
CN5
PS1
USB1
USB3
MODEM
DIO
JP2
J1
JP5
LCD1
J4
COM1
IDE1
IR
JC1
JP3
LPT
JP4
J5
SATA1
CN3
SATA2
LAN1
JC2
CN2
AU1
PWIN
CN1
CD_IN
I_SP
FAN1
Locating Jumpers and Connectors (front side)
V170 SBC User Manual
9
FDD1
2.4 Jumper Setting
Label
Function
Note
JC1
LVDS Panel Power Selector
3x1 header, pitch 2.0 mm
JP1
JP2
2.4.1
COM1,COM2 RS232 +5V /
+12V Power Setting
COM3,COM4 RS232 +5V /
+12V Power Setting
2*6 header, pitch 2.0 mm
2*6 header, pitch 2.0 mm
JP3
RS232/422/485 Selector
2x3 header, pitch 2.0 mm
JP4
RS232/422/485 Selector
2x3 header, pitch 2.0 mm
JP5
RS232/422/485 Selector
2x3 header, pitch 2.0 mm
JBAT
Clear CMOS Contents
3x1 header, pitch 2.0 mm
JC1: LVDS Panel Power Select
JC1
LVDS Panel Power
3.3V (default)
5V
2.4.2
JP1: COM1, COM2
Pin #
RS232 +5V / +12V Power Setting
Signal
JP1
Signal
Pin #
Name
Name
1
RI(Default)
RI(Default)
2
3
RI
+12v
4
5
RI
+5V
6
7
RI(Default)
8
9
RI
RI(Default)
+12V
10
11
RI
+5V
12
COM1 Settings: Pin 1-2 short =, Standard COM Port, Pin 3-4 short = +12V, Pin 5-6 = +5V
COM2 Settings: Pin 7-8 short =, Standard COM Port, Pin 9-10 short = +12V, Pin 11-12 = +5V
V170 SBC User Manual
10
2.4.3
JP2: COM3,COM4
Pin #
RS232 +5V / +12V Power Setting
Signal Name
JP2
Signal Name
Pin #
1
RI(Default)
RI(Default)
2
3
RI
+12v
4
5
RI
+5V
6
7
RI(Default)
8
9
RI
RI(Default)
+12V
10
11
RI
+5V
12
COM3 Settings: Pin 1-2 short =, Standard COM Port, Pin 3-4 short = +12V, Pin 5-6 = +5V
COM4 Settings: Pin 7-8 short =, Standard COM Port, Pin 9-10 short = +12V, Pin 11-12 = +5V
2.4.4
JP3,JP4,JP5 COM2 Select RS232/422/485
The jumper can be configured to operate in RS-232/422/485 mode.
RS232
RS485
RS422
1-2
3-4
5-6
3-5
4-6
1-3
2-4
1-3
2-4
3-5
4-6
1-3
2-4
1-3
2-4
JP5
JP4
JP3
2.4.5
JBAT: Clear CMOS Contents
Use JBAT to clear the CMOS contents. Note that the ATX-power connector should be disconnected
from the board before clearing CMOS.
JBAT
V170 SBC User Manual
Setting
Function
Pin 1-2
Short/Closed
Normal
Pin 2-3
Short/Closed
Clear CMOS
11
2.5 Connectors and Pin Assignment
The table below lists the function of each of the board’s connectors.
Label
Function
Note
J1
PW/Reset Switch and Indicator Connector
2x5 header, pitch 2.0 mm
FDD1
Floppy Drive Connector
26 pin connector
LCD1
LVDS PANEL OUTPUT
40 pin connector
CN3
INVERTER BKL Connector
1x4 header, pitch 2.54 mm
PS1
PS/2 Keyboard/Mouse Connectors
PS/2 connector
USB1
USB 4/5 Connectors
2x4 header, pitch 2.0 mm
I_SP
INTERNAL SPEAKER Connector
COM3/COM4 D-SUB 9PIN Connector X 2
(UP-COM3, DOWN-COM4)
4x1 header, pitch 2.54 mm
USB3
USB2/3 Connectors
2x4 header, pitch 2.0 mm
LAN1
RJ45 + USB0/1 connector
RJ45/USB connector
CD_IN
CD-In Audio Connector
4x1 header, pitch 2.54 mm
LPT
Parallel Port ( 26PIN Header)
13x2 pin header
PWIN
DC Jack
CN1
12V DC IN (Optional 24V)
COM2 + CRT (D-SUB 9PIN+D-SUB 15PIN
Connector)
ATX 12V DC-IN (Optional 24V)
4 pin ATX connector
COM1
Com port connector
2x5 header, pitch 2.0 mm
JC2
External Audio Connector
2x5 header, pitch 2.0 mm
MODEM
Onboard modem connector
2x8 header, pitch 2.0 mm
CN5
External PS/2 Keyboard /Mouse Connector
2x4 header, pitch 2.0 mm
SATA1,SATA2
SATA HDD Connector
SATA connector
DIO
Digital 4-in 4-out I/O Connector
2x5 header, pitch 2.0 mm
IDE1
IDE Connector
2x22 header, pitch 2.0 mm
CN2
ATX Power Supply Connector
20 pin ATX connector
FAN1,FAN2
CPU Fan Power Connector
3x1 header, pitch 2.0 mm
AU1
Line Out, Mic In Connector
3.5mm audio jack
IR
IrDA Connector
5x1 header, pitch 2.0 mm
J4
J5
* Not Default Connector
V170 SBC User Manual
12
9 pin com port connector
4 pin DC Jack
2.5.1
2.5.2
J1: PW/Reset Switch and Indicator Connector
Signal Name
Pin
Pin
Signal Name
Ground
1
2
PW-ON
Ground
3
4
Reset_SW
IDE_LED-
5
6
IDE_LED+
Power_LED+
7
8
Power_LED-
LAN_LED-
9
10
LAN_LED+
FDD1: Floppy Drive Connector
FDD is a slim 26-pin connector and will support up to 2.88MB FDD.
V170 SBC User Manual
13
Signal
Name
Pin #
Pin #
Signal
Name
VCC
1
2
INDEX
VCC
3
4
DRV_SEL
VCC
5
6
DSK_CH
NC
7
8
NC
NC
9
10
MOTOR
DINST
11
12
DIR
NC
13
14
STEP
GND
15
16
WDATA
GND
17
18
WGATE
GND
19
20
TRACK
NC
21
22
WPROT
GND
23
24
RDATA
GND
25
26
SIDE
2.5.3
LCD1: LVDS PANEL OUTPUT
Signal Name
VDD
VDD
Ground
Ground
AOM
AOP
Ground
A1M
A1P
Ground
A2M
A2P
Ground
CLK1M
CLK1P
Ground
A3M
A3P
NC
NC
2.5.4
2.5.5
Pin #
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
CN3: INVERTER BKL CONNECTOR
Pin #
Signal Name
1
Ground
2
Ground
3
ENABKL
4
12V
PS1: PS/2 Keyboard/Mouse Connectors
V170 SBC User Manual
Pin #
Signal Name
1
Data
2
No Connection
3
Ground
4
+5V
5
Clock
6
No Connection
14
Pin #
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
Signal Name
A4M
A4P
Ground
A5M
A5P
Ground
A6M
A6P
Ground
CLK2M
CLK2P
Ground
A7M
A7P
NC
NC
NC
NC
NC
NC
2.5.6
2.5.7
USB1: USB 4/5 Connectors
The following table shows the pin outs of the USB pin headers connectors.
Overall, the one pin header support four USB ports (USB 2.0 compliant).
Signal
Name
Pin
Pin
Signal
Name
Vcc
1
2
Vcc
USB5-
3
4
USB4-
USB5+
5
6
USB4+
Ground
7
8
Ground
I_SP : INTERNAL SPEAKER Connector
V170 SBC User Manual
Pin #
Signal Name
1
SPK_LN
2
SPK_LO
3
SPK_RN
4
SPK_RO
15
2.5.8
J4: COM3/COM4 D-SUB 9PIN Connector X 2 (UP-COM3, DOWNCOM4)
Signal Name
Signal Name
Pin
Pin
DCD, Data carrier detect
1
6
DSR, Data set ready
RXD, Receive data
2
7
RTS, Request to send
TXD, Transmit data
3
8
CTS, Clear to send
DTR, Data terminal ready
4
9
RI, Ring indicator
Ground
5
Signal Name
Signal Name
Pin
Pin
DCD, Data carrier detect
1
6
DSR, Data set ready
RXD, Receive data
2
7
RTS, Request to send
TXD, Transmit data
3
8
CTS, Clear to send
DTR, Data terminal ready
4
9
RI, Ring indicator
Ground
5
V170 SBC User Manual
16
2.5.9
USB3: USB2/3 Connectors
The following table shows the pin outs of the USB pin headers connectors.
Overall, one pin header supports four USB ports (USB 2.0 compliant).
2.5.10 LAN1 :
Signal
Name
Pin
Pin
Signal
Name
Vcc
1
2
Vcc
USB3-
3
4
USB2-
USB3+
5
6
USB2+
Ground
7
8
Ground
RJ45 + USB0/1 connector
2.5.11 CD_IN: CD-In Audio Connector
V170 SBC User Manual
Pin #
Signal Name
1
CD Audio R
2
Ground
3
Ground
4
CD Audio L
17
2.5.12 LPT : Parallel Port ( 26PIN Header)
2.5.13 PWIN:DC POWER IN (DC19V ~ DC24V)
V170 SBC User Manual
18
2.5.14 J5 : COM2 + CRT (D-SUB 9PIN+D-SUB 15PIN Connector)
Signal Name
Signal Name
Pin
Pin
DCD, Data carrier detect
1
6
DSR, Data set ready
RXD, Receive data
2
7
RTS, Request to send
TXD, Transmit data
3
8
CTS, Clear to send
DTR, Data terminal ready
4
9
RI, Ring indicator
Ground
5
Signal Name
Pin
Pin
Red
1
9
+5V
Green
2
10
Ground
Blue
3
11
NC
NC
4
12
SPD2
Ground
5
13
HSYNC
Ground
6
14
VSYNC
Ground
7
15
SPCLK2
Ground
8
V170 SBC User Manual
19
Signal Name
2.5.15 CN1: ATX 12V/+12V Power Connector
Pin #
Signal Name
1
Ground
2
Ground
3
+12V
4
+12V
2.5.16 COM1: Com port connector
Signal Name
Pin
Pin
Signal Name
DCD, Data carrier detect
1
2
DSR, Data set ready
RXD, Receive data
3
4
RTS, Request to send
TXD, Transmit data
5
6
CTS, Clear to send
DTR, Data terminal ready
7
8
RI, Ring indicator
Ground
9
10
No Connect.
2.5.17 JC2: External Audio Connector
JC2 is a 10-pin header that is used to connect to the optional audio cable card
that integrates jacks for Line Out and MIC.
Signal Name
Pin
Pin
Signal Name
MIC2_IN_L
1
2
Ground
MIC2_IN_R
3
4
NC
LINE2_OUT_R
5
6
MIC2_JD
FRONT_IO_SEN
7
8
INT_SP_DIS
LINE2_OUT_L
9
10
MIC2_JD
V170 SBC User Manual
20
2.5.18 MODEM: Onboard modem connector
Signal Name
Pin
MODEM
Pin
Signal Name
NC
1
2
Ground
DCD, Data carrier detect
3
4
RXD, Receive data
TXD, Transmit data
5
6
DTR, Data terminal ready
DSR, Data set ready
7
8
RTS, Request to send
+5V
9
10
NC
CTS, Clear to send
11
12
RI, Ring indicator
NC
13
14
MODEM SP
MODEM RESET
15
16
Ground
2.5.19 CN5: External PS/2 Keyboard /Mouse Connector
Pin
Pin
Signal
Name
KB-DATA
1
2
M-DATA
KB-CLK
3
4
M-CLK
GND
5
6
GND
VCC
7
8
Vcc
Signal
Name
2.5.20 SATA1,SATA2 : SATA HDD Connector
2.5.21 DIO: Digital 4-in 4-out I/O Connector
V170 SBC User Manual
Signal
Name
Pin
Pin
Signal
Name
Ground
1
2
Vcc
Out3
3
4
Out1
Out2
5
6
Out0
Int3
7
8
Int1
Int2
9
10
Int0
21
2.5.22 IDE1 : IDE Connector
V170 SBC User Manual
Signal
Name
Pin #
Pin #
Signal
Name
Reset IDE
1
2
Ground
Host data 7
3
4
Host data 8
Host data 6
5
6
Host data 9
Host data 5
7
8
Host data 10
Host data 4
9
10
Host data 11
Host data 3
11
12
Host data 12
Host data 2
13
14
Host data 13
Host data 1
15
16
Host data 14
Host data 0
17
18
Host data 15
Ground
19
20
Key
DRQ0
21
22
Ground
Host IOW
23
24
Ground
Host IOR
25
26
Ground
IOCHRDY
27
28
Host ALE
DACK0
29
30
Ground
IRQ14
31
32
No connect
Address 1
33
34
No connect
Address 0
35
36
Address 2
Chip select 0
37
38
Chip select 1
Activity
39
40
Ground
Vcc
41
42
Vcc
Ground
43
44
N.C.
22
2.5.23 CN2 : ATX Power Supply Connector
11
20
1
10
Signal
Name
Pin
#
Pin
#
Signal
Name
3.3V
11
1
3.3V
-12V
12
2
3.3V
Ground
13
3
Ground
PS-ON
14
4
+5V
Ground
15
5
Ground
Ground
16
6
+5V
Ground
17
7
Ground
-5V
18
8
Power good
+5V
19
9
5VSB
+5V
20
10
+12V
2.5.24 FAN1,FAN2: CPU Fan Power Connector
FAN1, FAN2 is a 3-pin header for CPU fans. The fan must be a 12V (500mA)
fan.
Pin #
Signal Name
1
Ground
2
+12V
3
Rotation detection
2.5.25 AU1: Line Out, MIC Connector
V170 SBC User Manual
23
2.5.26 IR: IrDA Connector
IR is used for an optional IrDA connector for wireless communication.
V170 SBC User Manual
Pin #
Signal Name
1
+5V
2
No connect
3
Ir RX
4
Ground
5
Ir TX
24
This chapter describes how to set
BIOS configuration
z
Starting Setup
z
Award BIOS Setup
z
Standard CMOS Features
z
Advanced BIOS Features
z
Advanced Chipset Features
z
Integrated Peripherals
z
Power Management Setup
z
PnP/PCI Configurations
z
PC Health Status
z
Frequency/Voltage Control
z
Load Fail-Safe Defaults
z
Load Optimized Defaults
z
Set Supervisor/User Password
z
Save & Exit Setup
z
Exit Without Saving
V170 SBC User Manual
25
CHAPTER
Award BIOS Setup
3
Chapter 3 BIOS SETUP
3.1
Starting Setup
AwardBIOS™ has a built-in setup program that allows users to modify the basic
system configuration. The information is stored in battery-backed Flash so that it
retains the setup information even if the system power is turned off.
Note:
Values for the various setup items that appear on your own screen (including
default values) may not be the same as the values shown on the screen figures in
this chapter. This is because the BIOS is revised and updated from time to time.
If in doubt, check Winmate website for the latest BIOS versions and related
information.
The system BIOS is managing and executing a variety of hardware related
functions in the system, including:
¾ System date and time
¾ Hardware execution sequence
¾ Power management function
¾ Allocation of system resources
V170 SBC User Manual
26
3.2
Award BIOS Setup
Once you enter the Award BIOS™ CMOS Setup Utility, the Main Menu will appear
on the screen. The Main Menu allows you to select from several setup functions and
two exit choices. User the arrow keys to select among the items and press <Enter> to
accept and enter the sub-menu.
Phoenix - AwardBIOS CMOS Setup Utility
►
Standard CMOS Features
►
Advanced BIOS Features
Load Fail-Safe Defaults
►
Advanced Chipset Features
Load Optimized Defaults
►
Integrated Peripherals
Set Supervisor Password
►
Power Management Setup
Set User Password
►
PnP/PCI Configurations
Save & Exit Setup
►
PC Health Status
Exit Without Saving
Esc: Quit F9 : Menu in BIOS
►
Frequency/Voltage Control
↑↓← → : Select Item
F10: Save & Exit Setup
Time, Date, Hard Disk Type ...
The BISO Setup Main Menu screen is shown above.
Note that a brief description of each highlighted selection appears at the bottom of the
screen.
¾
Setup Items
The main menu includes the following main setup categories.
¾
Standard CMOS Features
This menu displays the basic information about your system.
¾
Advanced BIOS Features
Use this menu to set the advanced features available on your system.
¾
Advanced Chipset Features
Use this menu to change the values in the chipset registers and optimize
your system’s performance.
¾
Integrated Peripherals
Use this menu to specify your setting for integrated peripherals.
V170 SBC User Manual
27
¾
Power Management Setup
Use this menu to specify your setting for power management.
¾
PnP/PCI Configurations
This option configures how PnP (Plug and Play) and PCI expansion cards
operate in your system.
¾
PC Health Status
This entry shows the current system temperature and voltage.
¾
Frequency/Voltage Control
Use this menu to set system frequency and voltage control.
¾
Load Fail-Safe Defaults
Use this menu to install fail-safe defaults for all appropriate items in the
setup utility.
¾
Load Optimized Defaults
Use this menu to install optimized defaults for all appropriate items in the
setup utility.
¾
Set Supervisor Password
Use this menu option to set the BIOS supervisor password.
¾
Set User Password
Use this menu option to set the BIOS user password.
¾
Save & Exit Setup
Save the changes that you have made in the Setup Utility and exit the Setup
Utility.
¾
Exit Without Saving
Abandon all changes that you have made in the Setup Utility and exit the
Setup Utility.
V170 SBC User Manual
28
3.3
Standard CMOS Features
The Standard CMOS Features Setup allows users to configure system components
such as date, time, hard disk drive, floppy drive and display. Use the arrow keys to
highlight the item and then use the <Page Up> or <Page Down> keys to select the
value you want in each item.
Phoenix - AwardBIOS CMOS Setup Utility
Standard CMOS Features
Date (mm:dd:yy)
Time (hh:mm:ss)
►
►
►
►
Tue, Jun 12 2007
17 : 12 : 8
IDE Channel 0 Master
IDE Channel 0 Slave
IDE Channel 1 Master
IDE Channel 1 Slave
[Hitachi HTS541660J9S]
[None]
[None]
[None]
Drive A
Drive B
[1.44, 3.5 in.]
[None]
Video
Halt On
[EGA/VGA]
[All , But Keyboard]
Base Memory
Extended Memory
Total Memory
↑↓→←:Move
Enter:Select
F5: Previous Values
Item Help
Menu Level ►
Press [Enter] to enter
next page for detail hard
drive settings
640K
391168K
392192K
+/-/PU/PD:Value F10:Save Esc:Exit F1:Genenal Help
F6: Fail-Safe Defaults F7: Optimized Defaults
The standard CMOS Features screen is shown above. Follow each item:
¾
Date (mm : dd : yy)
Set the system date. Note that if you are running a Windows OS, this item
are automatically updated whenever you make changes to the Windows
Date.
¾
Time (hh : mm : ss)
Set the system time. The time is converted based on the 24-hour
military-time clock. For example, 5:00:00 p.m. is 17:00:00.
¾
IDE Channel 0/1 Master/Slave
Press <Enter> to enter the sub-menu to detailed options.
¾
Drive A/B
Set Drive A/B type choice
The choice: “None”, “360K, 5.25 in.”, “1.2M 5.25 in.”, “720K, 3.5 in.”,
V170 SBC User Manual
29
“2.88M, 3.5 in.” or “1.44M, 3.5 in.”.
¾
Video
This item defines the video mode of the system. Leave this item at the
default value.
The choice: ”EGA/VGA*”, ”CGA 40”, ”CGA 80”, or ”MONO”.
* default value
¾
Halt On
This item defines the operation of the system POST (Power-On Self Test)
routine. You can use this item to select which situation you want the BIOS
to stop the POST process and notify you.
The choice: “All errors”, “No Errors”, “All, but keyboard”, “All, but
Diskette”, or “All, but Disk/Key”.
¾
Base Memory/Extended Memory/Total Memory
These items are automatically detected by the system at start up time.
These are display-only fields. You can not make change to these fields.
Follow steps as IDE adapter below:
¾
IDE HDD Auto-Detection
The IDE adapters control the hard disk drive. Use a separate sub-menu to
configure each hard disk drive. Press <Enter> to auto-detect HDD on this
channel. If detection is successful, it fills the remaining fields on this menu.
¾
IDE Channel 0/1 Master/Slave
Selecting ‘Manual’ lets you set the remaining fields on this screen and select
the type of fixed disk.
The choice: None, Auto, or Manual
¾
Access Mode
Choose the access mode for this hard disk.
The choice: ”CHS”, ”LBA”, ”Large”, or ”Auto”.
¾
Capacity
Note that the disk drive capacity (approx.) is usually slightly greater than
the size of a formatted disk given by a disk checking program.
¾
Cylinder
Set the number of cylinders for this hard disk.
„ Min = 0, Max = 65535
¾
Head
V170 SBC User Manual
30
Set the number of read/write heads
„ Min = 0, Max = 255
¾
Precomp
Warning: Setting a value of 65535 means no hard disk.
„ Min = 0, Max =65535
¾
Landing Zone
Set the Landing Zone size.
„ Min = 0, Max = 65535
¾
Sector
Number of sector per-track.
„ Min = 0, Max = 255
V170 SBC User Manual
31
3.4
Advanced BIOS Features
This section allows you to configure your system for basic operation. You have the
opportunity to select the system’s default speed, boot-up sequence, keyboard
operation, shadowing and security.
Phoenix - AwardBIOS CMOS Setup Utility
Advanced BIOS Features
► Hard Disk Boot Priority
Virus Warning
CPU L1 & L2 Cache
CPU L2 Cache ECC Checking
Quick Power On Self Test
First Boot Device
Second Boot Device
Third Boot Device
Boot Other Device
Swap Floppy Drive
Boot Up Floppy Seek
Boot Up NumLock Status
Typematic Rate Setting
X Typematic Rate (Chars/Sec)
X Typematic Delay (Msec)
Security Option
MPS Version Control For OS
OS Select For DRAM > 64MB
Video BIOS Shadow
Small Logo(EPA) Show
[Press Enter]
[Disabled]
[Enabled]
[Enabled]
[Enabled]
[USB-FDD]
[Hard Disk]
[LS120]
[Enabled]
[Disabled]
[Disabled]
[On]
[Disabled]
6
250
[Setup]
[1.4]
[Non-OS2]
[Enabled]
[Disabled]
Item Help
Menu Level ►
↑↓→←:Move
Enter:Select +/-/PU/PD:Value F10:Save Esc:Exit F1:Genenal Help
F5: Previous Values
F6: Fail-Safe Defaults F7: Optimized Defaults
¾
Hard-Disk Boot Priority
This is for setting the priority of the hard disk boot order when the “Hard
Disk” option is selected in the “[First/Second/Third] Boot Device” menu
item. You can change the priority on the List.
¾
Virus Warning
Allow you to choose the Virus Warning feature for IDE Hard Disk boot
sector protection. Enable this item to prevent someone from writing data
into this area.
„ The choice: Enabled or Disabled
„ Default: Disabled
¾
CPU L1 & L2 Cache
All processors that can be installed in this motherboard use internal level of
V170 SBC User Manual
32
L1 cache memory to improve performance. Leave this item at the default
value for better performance.
„ The choice: Enabled or Disabled
„ Default: Enabled
¾
CPU L2 Cache ECC Checking
This feature enables or disables the L2 (Level 2 or Secondary) cache's ECC
checking function.
„ The choice: Enabled or Disabled
„ Default: Enabled
¾
Quick Power On Self Test
Enable this item to shorten the power on testing (POST) and have your
system start up faster. You might like to this item after you are confident
that your system hardware is operating smoothly.
„ The choice: Enabled or Disabled
„ Default: Enabled
¾
First/Second/Third Boot Device
Set the boot device sequence as BIOS attempts to load the disk
operating system.
„
„
The choice: Floppy, LS120, Hard Disk, CDROM, ZIP100, USB-FDD,
USB-ZIP or USB-CDROM.
Default: Hard Disk (First) / CDROM (Second) / Removable (Third)
¾
Boot Other Device
If you enable this item, the system searches all other possible locations for
and operating system if it fails to find one in the devices specified under the
First, Second and the Third boot devices.
„ The choice: Enabled or Disabled
„ Default: Enabled
¾
Swap Floppy Drive
„ The choice: Enabled or Disabled
„ Default: Disabled
¾
Boot Up NumLock Status
This item defines if the keyboard NumLock key is active when your system
V170 SBC User Manual
33
is started.
„ The choice: On or Off
„ Default: On
¾
Typematic Rate Setting
This Enables “Typematic Rate” and “Typematic Delay” functions.
„ The choice: Enabled, Disabled
„ Default: Disabled
¾
Typematic Rate (Chars/Sec)
This item sets the rate (characters/second) at which the system retrieves a
signal from a depressed key.
„ The choice: 6, 8, 10, 12, 15, 20, 24, 30
„ Default: 6
¾
Typematic Delay (Msec)
This item sets the delay between when the key was first pressed and when
the system begins to repeat the signal from the depressed key.
„ The choice: 250, 500, 750, 1000
„ Default: 250
¾
Security Option
If you have installed password protection, this item defines if the password
is required at system start up, or if it is only required with a user tries to
enter the Setup Utility.
„ The choice: Setup or System
„ Default: Setup
¾
MPS Version Control For OS
„
„
¾
The choice: 1.1 or 1.4
Default: 1.4
OS Select For DRAM > 64MB
Select OS2 only if you are running OS/2 operating system with greater than
64MB of RAM on the system.
„ The choice: Non-OS2 or OS2
„ Default: Non-OS2
V170 SBC User Manual
34
¾
Video BIOS Shadow
Enabled copies Video BIOS to shadow RAM Improves performance.
„ The choice: Enabled or Disabled
„ Default: Enabled
¾
Small Logo (EPA) Show
„
„
The choice: Enabled or Disabled
Default: Disabled
V170 SBC User Manual
35
3.5
Advanced Chipset Features
These items define critical timing parameters of the motherboard. You should leave
the items at their default values unless you are very familiar with the technical,
specifications of your system hardware. If you change the values incorrectly, you may
introduce fatal error or recurring instability into your system.
Phoenix - AwardBIOS CMOS Setup Utility
Advanced Chipset Features
► DRAM Clock/Drive Control
► AGP & P2P Bridge Control
► CPU & PCI Bus Control
Memory Hole
System BIOS Cacheable
Video RAM Cacheable
Init Display First
[Press Enter]
[Press Enter]
[Press Enter]
[Disabled]
[Enabled]
[Disabled]
[PCI Slot]
Item Help
Menu Level ►
↑↓→←:Move
Enter:Select +/-/PU/PD:Value F10:Save Esc:Exit F1:Genenal Help
F5: Previous Values
F6: Fail-Safe Defaults F7: Optimized Defaults
¾
DRAM Clock/Drive Control
►
DRAM Clock
The chipset supports synchronous and asynchronous mode between
host clock and DRAM clock frequency.
„ The choice: By SPD, 200 MHz, 266MHz, 333MHz
„ Default: By SPD
►
DRAM Timing
The value in this field depends on the memory modules installed in
your system. Changing the value from the factory setting is not
recommended unless you install new memory that has a different
performance rating than the original modules.
„ The choice: Manual, Auto By SPD
„ Default: Auto By SPD
V170 SBC User Manual
36
¾
►
Read to Precharge (Trtp)
„ The choice: 2T, 3T
„ Default: 2T
►
Write to Read CMD (Trtp)
„ The choice: 1T/2T, 2T/3T
„ Default: 1T/2T
►
Write Recovery Time (Twr)
„ The choice: 2T, 3T, 4T, 5T
„ Default: 4T
►
DRAM Command Rate
„ The choice: 2T Command, 1T Command
„ Default: 2T Command
AGP & P2P Bridge Control
The sub menu is as below:
► VGA Share Memory Size
„ The choice: Settings: Disabled, 8M, 16M, 32M, 64M, 128M
„ Default: 64M
►
Panel Type
This setting refers to the native resolution of the display being used
with the system.
„ The choice: Key in a HEX number [Min = 0000, Max = 000F].
„ Default: 0A
Panel ID
Resolution
Channel
0
640x480
1
18 bits
1
800x600
1
18 bits
2
1024x768
1
18 bits
3
1280x768
1
18 bits
4
1280x1024
2
18 bits
5
1400x1050
2
18 bits
6
1600x1200
2
18 bits
7
1280x800
1
18 bits
8
800x480
1
18 bits
9
1024x768
2
18 bits
V170 SBC User Manual
37
RGB-Color 18/24 bits
¾
A
1024x768
1
24 bits
B
1024x768
2
24 bits
C
1280x768
1
24 bits
D
1280x1024
2
24 bits
E
1400x1050
2
24 bits
F
1600x1200
2
24 bits
CPU & PCI Bus Control
When enter into this sub menu, options are as below:
► PCI Master 0 WS Write
„ The choice: Enabled, Disabled
„ Default: Enabled
¾
►
PCI Delay Transaction
„ The choice: Enabled, Disabled
„ Default: Enabled
►
DRDY_Timing
„ The choice: Slowest, Default, Optimize
„ Default: Optimize
Memory Hole
„
„
¾
System BIOS Cacheable
„
„
¾
The choice: Enabled or Disabled
Default: Enabled
Video RAM Cacheable
„
„
¾
The choice: Disabled or 15-16M
Default: Disabled
The choice: Enabled or Disabled
Default: Disabled
Init Display First
„
„
The choice: PCI Slot or AGP
Default: PCI Slot
V170 SBC User Manual
38
3.6
Integrated Peripherals
Phoenix - AwardBIOS CMOS Setup Utility
Integrated Peripherals
► VIA OnChip IDE Device
► VIA OnChip PCI Device
► Super IO Device
Onboard Serial Port 3
Serial Port 3 Use IRQ
Onboard Serial Port 4
Serial Port 4 Use IRQ
► USB Device Setting
[Press Enter]
[Press Enter]
[Press Enter]
[3E8]
[IRQ5]
[2E8]
[IRQ10]
[Press Enter]
Item Help
Menu Level ►
↑↓→←:Move
Enter:Select +/-/PU/PD:Value F10:Save Esc:Exit F1:Genenal Help
F5: Previous Values
F6: Fail-Safe Defaults F7: Optimized Defaults
¾
VIA OnChip IDE Device
►
SATA Controller
„ The choice: Enabled, Disabled
„ Default: Enabled
►
IDE DMA transfer access
„ The choice: Enabled, Disabled
„ Default: Enabled
►
Secondary Master PIO
„ The choice: Auto, Mode 0, Mode 1, Mode 2, Mode 3, Mode4
„ Default: Auto
►
Secondary Slave PIO
„ The choice: Auto, Mode 0, Mode 1, Mode 2, Mode 3, Mode4
„ Default: Auto
►
Secondary Master UDMA
V170 SBC User Manual
39
„
„
¾
►
Secondary Slave UDMA
„ The choice: Disabled, Auto
„ Default: Auto
►
IDE HDD Block Mode
„ The choice: Enabled, Disabled
„ Default: Enabled
VIA OnChip PCI Device
►
¾
The choice: Disabled, Auto
Default: Auto
Azalia HAD Controller
„ The choice: Auto, Disabled
„ Default: Auto
Super IO Device
►
Onboard FDC Controller
„ The choice: Enabled, Disabled
„ Default: Enabled
►
Onboard Serial Port 1
„ The choice: Disabled, 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4,
2E8/IRQ3, Auto
„ Default: 3F8/IRQ4
►
Onboard Serial Port 2
„ The choice: Disabled, 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4,
2E8/IRQ3, Auto
„ Default: 2F8/IRQ3
►
UART Mode Select
„ The choice: IrDA, ASKIR, Normal
„ Default: Normal
►
Onboard Parallel Port
„ The choice: Disabled, 378/IRQ7, 278/IRQ5, 3BC/IRQ7
„ Default: 378/IRQ7
V170 SBC User Manual
40
►
¾
Parallel Port Mode
„ The choice: SPP, EPP, ECP, ECP/EPP, Normal
„ Default: SPP
Onboard Serial Port 3
This option is used to assign the I/O address and Interrupt Request (IRQ)
for the onboard Serial Port.
„ The choice: Disabled, 3F8, 2F8, 3E8, 2E8
„ Default: 3E8
¾
Serial Port 3 Use IRQ
„
„
¾
The choice: IRQ3, IRQ4, IRQ5, IRQ9, IRQ10, IRQ11
Default: IRQ5
Onboard Serial Port 4
This option is used to assign the I/O address and Interrupt Request (IRQ)
for the onboard Serial Port.
„ The choice: Disabled, 3F8, 2F8, 3E8, 2E8
„ Default: 2E8
¾
Serial Port 4 Use IRQ
„
„
¾
The choice: IRQ3, IRQ4, IRQ5, IRQ9, IRQ10, IRQ11
Default: IRQ10
USB Device Setting
► USB 1.0 Controller
Enable or disable Universal Host Controller Interface for Universal Serial
Bus.
„ The choice: Enabled, Disabled
„ Default: Disabled
►
USB 2.0 Controller
Enable or disable Enhanced Host Controller Interface for Universal
Serial Bus.
„ The choice: Enabled, Disabled
„ Default: Disabled
V170 SBC User Manual
41
►
USB Operation Mode
Auto decide USB device operation mode. If USB device was high
speed device, then it operated on high speed mode. If USB device was
full/low speed device, then it operated on full/low speed mode.
„ The choice: High Speed, Full/Low Speed
„ Default: High Speed
►
USB Keyboard Function
Enable or disable Legacy support of USB Keyboard
„ The choice: Enabled, Disabled
„ Default: Enabled
►
USB Mouse Function
Enable or disable Legacy support of USB Mouse
„ The choice: Enabled, Disabled
„ Default: Enabled
►
USB Storage Function
Enable or disable Legacy support of USB Mass Storage
„ The choice: Enabled, Disabled
„ Default: Enabled
V170 SBC User Manual
42
3.7
Power Management Setup
Phoenix - AwardBIOS CMOS Setup Utility
Power Management Setup
ACPI function
ACPI Suspend Type
Power Management Option
HDD Power Down
Suspend Mode
Video Off Option
Video Off Method
Soft-Off by PWRBTN
► Wakeup Event Detect
[Enabled]
[S1(POS)]
[User Define]
[Disabled]
[Disabled]
[Suspend -> Off]
[V/H SYNC+Blank]
[Instant-Off]
[Press Enter]
Item Help
Menu Level ►
↑↓→←:Move
Enter:Select +/-/PU/PD:Value F10:Save Esc:Exit F1:Genenal Help
F5: Previous Values
F6: Fail-Safe Defaults F7: Optimized Defaults
¾
ACPI function
„
„
¾
The choice: Disabled, Enabled
Default: Enabled
ACPI Suspend Type
„ The choice: S1 (POS), S3 (STR), S1 & S3
„ Default: S1 (POS)
S1/Power On Suspend (POS) is a low power state. In this state, no system
context (CPU or chipset) is lost and hardware maintains all system contexts.
S3/Suspend To RAM (STR) is a power-down state. In this state, power is
supplied only to essential components such as main memory and
wakeup-capable devices. The system context is saved to main memory, and
context is restored from the memory when a "wakeup" event occurs. The S1
& S3 option is depends on the OS to select S1 or S3.
¾
Power Management Option
„
„
¾
The choice: User Define, Min Saving, Max Saving
Default: User Define
HDD Power Down
V170 SBC User Manual
43
Sets the length of time for a period of inactivity before powering down the
hard disk.
„ The choice: Disabled, 1~15(minutes)
„ Default: Disabled
¾
Suspend Mode
„
„
¾
Settings: Disabled, 1 Min, 2 Min, 4 Min, 6 Min, 8 Min, 10 Min, 20
Min, 30 Min, 40 Min, 1 Hour
Default: Disabled
Video Off Option
Select whether or not to turn off the screen when system enters power
saving mode, ACPI OS such as Windows XP will override this option.
„ The choice: Always On, Suspend -> Off
„ Default: Suspend -> Off
¾
Video Off Method
„
„
¾
The choice: Blank Screen, V/H SYNC+Blank, DPMS Support
Default: V/H SYNC+Blank
Soft-Off by PWRBTN
System is turned off if power button is pressed for more than four seconds,
or Power button functions as a normal power-on/-off button.
„ The choice: Delay 4 Sec, Instant-Off
„ Default: Instant-Off
¾
Ac Loss Auto Restart
The field defines how the system will respond after an AC power loss
during system operation.
„ The choice: Off, On, Former-Sts
„ Default: Former-Sts
¾
Wakeup Event Detect
►
PS2KB Wakeup Select
When selecting Password, press Enter to change password. The
maximum number of characters is eight.
„ Settings: Hot Key, Password
„ Default: Hot Key
V170 SBC User Manual
44
►
PS2KB Wakeup Key Select
Sets a Hot Key to restore the system from the power saving mode to an
active state.
„ Settings: Ctrl+F1, Ctrl+F2, Ctrl+F3, Ctrl+F4, Ctrl+F5, Ctrl+F6,
Ctrl+F7, Ctrl+F8, Ctrl+F9, Ctrl+F10, Ctrl+F11, Ctrl+F12, Power,
Wake, Any Key
„ Default: Any Key
►
PS2MS Wakeup Key Select
Enables any mouse activity to restore the system from the power
saving mode to an active state.
„ Settings: Any Button, Left Button, Right Button
„ Default: Any Button
►
PS2 Keyboard Power On
„ Settings: Disabled, Enabled
„ Default: Disabled
►
PS2 Mouse Power On
„ Settings: Disabled, Enabled
„ Default: Disabled
►
Modem Ring Resume
„ Settings: Enabled, By OS
„ Default: Enabled
►
RTC Alarm Resume
Sets a scheduled time and/or date to automatically power on the
system.
„ Settings: Disabled, Enabled
„ Default: Disabled
►
Date (of Month)
The field specifies the date for “RTC Alarm Resume”.
►
Resume Time (hh:mm:ss)
The field specifies the time for “RTC Alarm Resume”.
V170 SBC User Manual
45
3.8
PnP/PCI Configurations
Phoenix - AwardBIOS CMOS Setup Utility
PnP/PCI Configurations
Resources Controlled By
X IRQ Resources
[Auto(ESCD)]
Press Enter
Item Help
Menu Level ►
Select Yes if you are using
a Plug and Play capable
operating system Select
No if you need the BIOS
to configure non-boot
devices
↑↓→←:Move
Enter:Select +/-/PU/PD:Value F10:Save Esc:Exit F1:Genenal Help
F5: Previous Values
F6: Fail-Safe Defaults F7: Optimized Defaults
¾
Resources Controlled By
Enables the BIOS to automatically configure all the Plug-and-Play
compatible Devices, e.g. assign IRQ, DMA and memory base address fields.
Or manually Unlocks “IRQ Resources” for manual configuration.
„ The choice: Auto (ESCD), Manual
„ Default: Auto (ESCD)
V170 SBC User Manual
46
3.9
PC Health Status
Phoenix - AwardBIOS CMOS Setup Utility
PC Health Status
CPU Warning Temperature
Current System Temp.
Current CPU1 Temperature
Current CPUFAN1 Speed
Current CPUFAN2 Speed
IN0(V)
IN1(V)
IN2(V)
+5V
+12 V
-12 V
-5V
VBAT(V)
5VSB(V)
Shutdown Temperature
[70º C/158º F]
71º C/159º F
85º C/185º F
0 RPM
0 RPM
0.80 V
0.00 V
3.24 V
4.91 V
11.85 V
-12.69 V
-62.03 V
2.97 V
4.89 V
[70º C/158º F]
Item Help
Menu Level ►
↑↓→←:Move
Enter:Select +/-/PU/PD:Value F10:Save Esc:Exit F1:Genenal Help
F5: Previous Values
F6: Fail-Safe Defaults F7: Optimized Defaults
¾
¾
CPU Warning Temperature
„
The choice: Disabled, 50°C/122°F, 53°C/127°F, 56°C/133°F, 60°C/140°F,
63°C/145°F, 66°C/151°F, 70°C/158°F,
„
Default: Disabled
Shutdown Temperature
This item allows you to select the shutdown temperature. The system will
automatically shutdown while the CPU temperature has reach to the value
you have set.
„ The choice: 60°C/140°F, 65°C/149°F, 70°C/158°F, 75°C/167°F or
„
Disabled
Default: Disabled
V170 SBC User Manual
47
3.10 Frequency/Voltage Control
Phoenix - AwardBIOS CMOS Setup Utility
PC Health Status
CPU Clock Ratio
Auto Detect PCI Clk
Spread Spectrum
CPU Clock
[10 X]
[Enabled]
[Disabled]
[100MHz]
Item Help
Menu Level ►
↑↓→←:Move
Enter:Select +/-/PU/PD:Value F10:Save Esc:Exit F1:Genenal Help
F5: Previous Values
F6: Fail-Safe Defaults F7: Optimized Defaults
¾
Auto Detect PCI Clk
„
„
¾
The choice: Disabled, Enabled
Default: Disabled
Spread Spectrum
When the motherboard's clock generator pulses, the extreme values (spikes)
of the pulses create EMI (Electromagnetic Interference). The Spread
Spectrum function reduces the EMI generated by modulating the pulses so
that the spikes of the pulses are reduced to flatter curves.
„ The choice: Disabled, 0.20%, 0.25%, 0.35%
„ Default: Disabled
V170 SBC User Manual
48
3.11 Load Fail-Safe Defaults
When you press <Enter> on this item, you will get confirmation dialog box with a
message similar to:
„ Load Fail-Safe Defaults (Y/N)? N
„ Pressing ‘Y’ loads the BIOS default values for the most stable,
minimal performance system operations.
Phoenix - AwardBIOS CMOS Setup Utility
►
Standard CMOS Features
►
Frequency/Voltage Control
►
Advanced BIOS Features
Load Fail-Safe Defaults
►
Advanced Chipset Features
Load Optimized Defaults
►
Integrated Peripherals
Set Supervisor Password
►
►
Power Management Setup
Set User Password
Load Fail-Safe Defaults (Y/N)? N
PnP/PCI Configurations
Save & Exit Setup
►
PC Health Status
Exit Without Saving
Esc : Quit F9 : Menu in BIOS
↑↓← → : Select Item
F10 : Save & Exit Setup
Load Fail-Safe Defaults
This option is for restoring all the default fail-safe BIOS settings. These values are set
by the motherboard manufacturer to provide a stable system with basic performance.
V170 SBC User Manual
49
3.12 Load Optimized Defaults
When you press <Enter> on this item, you will get confirmation dialog box with a
message similar to:
„ Load Optimized Defaults (Y/N)? N
„ Pressing ‘Y’ loads the default values that are factory-set for optimal
performance system operation.
Phoenix - AwardBIOS CMOS Setup Utility
►
Standard CMOS Features
►
Frequency/Voltage Control
►
Advanced BIOS Features
Load Fail-Safe Defaults
►
Advanced Chipset Features
Load Optimized Defaults
►
Integrated Peripherals
Set Supervisor Password
►
►
Power Management Setup
Set User Password
Load Optimized Defaults (Y/N)? N
PnP/PCI Configurations
Save & Exit Setup
►
PC Health Status
Exit Without Saving
Esc : Quit F9 : Menu in BIOS
↑↓← → : Select Item
F10 : Save & Exit Setup
Time, Date, Hard Disk Type ...
This option is for restoring all the default optimized BIOS settings. The default
optimized values are set by the motherboard manufacturer to provide a stable system
with optimized performance.
V170 SBC User Manual
50
3.13 Set Supervisor/User Password
Phoenix - AwardBIOS CMOS Setup Utility
►
Standard CMOS Features
►
Advanced BIOS Features
Load Fail-Safe Defaults
►
Advanced Chipset Features
Load Optimized Defaults
►
Integrated Peripherals
Set Supervisor Password
►
Set User Password
►
Power Management Setup
Enter Password:
PnP/PCI Configurations
►
PC Health Status
Exit Without Saving
Esc : Quit F9 : Menu in BIOS
►
Frequency/Voltage Control
Save & Exit Setup
↑↓← → : Select Item
F10 : Save & Exit Setup
Change/Set/Disable Password
Steps to set supervisor/user password are described as follows:
¾
¾
New password setting:
1. While pressing <Enter> to set a password, a dialog box appears to ask
you enter a password.
2. Key in a new password. The password can not exceed eight
characters.
3.
Please Enter Your Password
System will request you to confirm the new password again.
4.
Please Confirm Your Password
When completed, new code takes effect.
No Password Setting:
If you wants to disable the password, just <Enter> as a password input is requested.
¾
If you forget password:
If you forget the password, the only way to access the system is to clear the CMOS
memory. You may remove the battery from motherboard and put it back to clear the
setting.
V170 SBC User Manual
51
3.14 Save & Exit Setup
Phoenix - AwardBIOS CMOS Setup Utility
►
Standard CMOS Features
►
Frequency/Voltage Control
►
Advanced BIOS Features
Load Fail-Safe Defaults
►
Advanced Chipset Features
Load Optimized Defaults
►
Integrated Peripherals
Set Supervisor Password
►
►
Power Management Setup
Set User Password
Save to CMOS and Exit (Y/N)?
PnP/PCI Configurations
Save & Exit Setup
►
PC Health Status
Exit Without Saving
Esc : Quit F9 : Menu in BIOS
↑↓← → : Select Item
F10 : Save & Exit Setup
Save Data to CMOS
¾
Pressing <Enter> on this item asks for confirmation:
„ Save to CMOS and Exit (Y/N)? Y
„ Press ‘Y’ stores the selections made in the menus of CMOS – a special
section of memory that recorded in after you turn your system off. The
next time you turn on your computer, the BIOS configures your system
according to the Setup selections recorded in he CMOS memory of the
chipset. After saving the values the system is restarted again.
V170 SBC User Manual
52
3.15 Exit Without Saving
Phoenix - AwardBIOS CMOS Setup Utility
►
Standard CMOS Features
►
Frequency/Voltage Control
►
Advanced BIOS Features
Load Fail-Safe Defaults
►
Advanced Chipset Features
Load Optimized Defaults
►
Integrated Peripherals
Set Supervisor Password
►
►
Power Management Setup
Set User Password
Quit Without Saving (Y/N)?
PnP/PCI Configurations
Save & Exit Setup
►
PC Health Status
Exit Without Saving
Esc : Quit F9 : Menu in BIOS
↑↓← → : Select Item
F10 : Save & Exit Setup
Abandon all Data
¾
Press <Enter> on this item asks for confirmation:
„ Quit Without Saving (Y/N)? Y
„ This allows you to exit from Setup without storing in CMOS any
change. The previous selections remain in effect. This exits from
Setup utility and restarts your computer.
V170 SBC User Manual
53
CHAPTER
4
Chipset Driver Installation
This chapter offers information on the chipset software
installation utility.
Sections include:
z
Introduction
z
Installation of Chipset Utility
z
Further Information
V170 SBC User Manual
54
Chapter 4 Chipset Driver Installation
4.1
Introduction
The V170 mainboard is equipped with VIA CX700 Companion Device. The
VIA Chipset Drivers should be installed first before the software drivers to
enable Plug & Play INF support for VIA chipset components. Follow the
instructions below to complete the installation.
4.2
Installation of Ethernet Driver
Step.1. After finishing the O.S. installation, insert the driver CD. Open the
VIA_HyperionPro_V512A folder and double click the setup.exe file.
Step.2 When the install wizard startup, click the “Next” button to continue.
V170 SBC User Manual
55
Step.3 Choose “I Agree” to confirm the License Agreement. And click the
“Next” button to continue.
Step.4 Pick up the component you want to install in your system. And click the
“Next” button to continue.
V170 SBC User Manual
56
Step.5 Confirm the installation list and click the “Next” button to continue.
Step.6 Review the installation status that all component you want to install were
well installed. And click the “Next” button to finish installation. You may have
to restart your computer to let system configuration finish.
4.3
Further information
Winmate web site: http://www.winmate.com.tw
V170 SBC User Manual
57
CHAPTER
Ethernet Driver Installation
This chapter offers information on the Ethernet.
Sections include:
z
Introduction
z
Installation of Ethernet Driver
z
Further Information
V170 SBC User Manual
58
5
Chapter 5 Ethernet Driver Installation
5.1
Introduction
The V170 mainboard is equipped with the Realtek RTL8110SBL Ethernet
controller combines a triple-speed IEEE 802.3 compliant Media Access
Controller (MAC) with a triple-speed Ethernet transceiver, 32-bit PCI bus
controller, and embedded memory. With state-of-the-art DSP technology and
mixed-mode signal technology, it offers high-speed transmission over CAT 5
UTP or CAT 3 UTP (10Mbps only) cable. Functions such as Crossover
Detection & Auto-Correction, polarity correction, adaptive equalization,
cross-talk cancellation, echo cancellation, timing recovery, and error correction
are implemented to provide robust transmission and reception capability at high
speeds.
The Ethernet port provides an On-board standard RJ-45 connector. The device
supports the PCI 10/100/1000Mbps Ethernet interface supports for host
communications with power management, and is compliant with the IEEE 802.3
specification for 10/100/ 1000Mbps.
5.2
Installation of Ethernet Driver
The Users must make sure which operating system you are using in the V170
Mainboard before installing the Ethernet drivers. Follow the steps below to
complete the installation of the Realtek RTL8110SBL LAN drivers. You will
quickly complete the installation.
V170 SBC User Manual
59
Setp.1. Insert the CD that comes with the motherboard. Open the file document
“RTL8169_8139_810x_663” and click on “Setup.exe” to execute the setup.
Setp.2. Click on “Next“ and “install” driver.
V170 SBC User Manual
60
Setp.3. Click “Finish” and restart the computer for new settings to take effect.
5.3
Further information
Winmate web site: http://www.winmate.com.tw
V170 SBC User Manual
61
CHAPTER
VGA Driver Installation
This chapter offers information on the VGA.
Sections include:
z
Introduction
z
Installation of VGA
z
Further Information
V170 SBC User Manual
62
6
Chapter 6 VGA Driver Installation
6.1
Introduction
The V170 Mainboard offers an integrated VGA/LCD Controller, 2D/3D GUI
engine, sharing memory architecture up to 64 MB. The specifications and
features are described as follows:
The V170 Mainboard supports CRT and TFT LCD displays. In addition, it also
supports CRT and flat panel display mode simultaneously.
The V170 Mainboard can be set in one of three configurations: on a CRT, on a
flat panel display, or on both simultaneously. The system is initially set to
simultaneous display mode. The Panel resolution supports up to 1280 x 1024
@18bpp or 24bpp.
6.2
Installation of VGA Driver
To install the VGA drivers, follow the steps below to proceed with the
installation.
Step.1. Enter the “Drivers\VGA\Win2k_xp“ folder in driver CD and double
click “setup.exe“.
V170 SBC User Manual
63
Step.2. Follow the installation steps and click the “Finish “to complete the
process.
6.3
Further information
Winmate web site: http://www.winmate.com.tw
V170 SBC User Manual
64
CHAPTER
AUDIO Driver Installation
This chapter offers information on the Audio.
Sections include:
z
Introduction
z
Installation of AUDIO
z
Further Information
V170 SBC User Manual
65
7
Chapter 7 AUDIO Driver Installation
7.1
Introduction
The V170 Mainboard is equipped with the VIA HD Codec VT1708A which is
delivering top quality audio performance, supporting the latest 8-channel, 24-bit,
192KHz audio content for an all-round high fidelity experience.
Integrating stereo DACs with a 100dB S/N ratio and compliant with the Intel®
High Definition Audio Rev. 1.0 specification, VIA HD Audio codecs include
leading edge features such as a high quality headphone amplifier, enhanced
recording support, and advanced power management features, making them
ideal for mobile devices.
7.2
Installation of Audio Driver
The users must make sure which operating system you are using in the V170
Mainboard before installing the Audio drivers. Follow the steps below to
complete the installation of the VIA HD Codec VT1708A Audio drivers. You
will quickly complete the installation. Follow the steps below to install the VIA
HD Codec VT1708A Audio Drivers.
Step.1 Click “SETUP” on the “ VIA_HDA_V302A” window.
V170 SBC User Manual
66
Step.2 Click the “Next “button on the Welcome window.
Step.3 Select “I Agree “and click the “Next “ button on the License Agreement
window.
V170 SBC User Manual
67
Step.4 Click the “Next “button on the Install List window.
Step.5 Click the “Next “button on the Installing Components List window.
V170 SBC User Manual
68
Step.7 Click the “Next “button on the Installing Status window.
Step.8 Click the “Next “button on the Welcome window.
V170 SBC User Manual
69
Step.9 Click the “Finish “button and restart your system.
7.3
Further information
Winmate web site: http://www.winmate.com.tw
V170 SBC User Manual
70
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement