Jeep Wrangler i407-WRA-JL 20210330v1 ˜ 1/22

Jeep Wrangler

i407-WRA-JL

7” Restyle In-Dash System

Installation Manual

˜

Model: Wrangler JL 2018-Up

˜

Model: Gladiator JT 2020-Up

Jeep

Model

Wrangler JL**

Year

2018 - Up

Gladiator JT** 2020 - Up

** OEM amplified vehicles require the KCX-F200INT (sold separately)

* The specified vehicles have been tested and have met compatibility specs at the time of testing. Compatibility is not guaranteed if the manufacturer has made production changes to the listed vehicles above.

Introduction

˜ Congratulations on purchasing the i407-WRA-JL. This installation manual is designed to take you through the step-by-step installation of i407-WRA-JL into a 2018-Up Jeep Wrangler JL or Jeep Gladiator JT 2020-

Up. Please familiarize yourself with the owners manual as this is a challenging installation. If you still have additional questions please call 1-800-TECH-101.

Note

˜ Design and specifications are subject to change without notice for improvement.

To Ensure Safe Use, Always Follow These Precautions

˜ The installation of this product requires specialized skills and experience. This is an installation that is challenging and time consuming even for installers with experience. A professional installer would typically take a minimum of 2-3 hours to complete this installation. We recommend that you have the product installed by an Alpine authorized dealer.

˜ Before you use this product, be sure to carefully read this installation manual and the separate user's manual so that you can use the product correctly. Alpine Electronics bears no responsibility for problems that arise as a result of failure to follow the instructions in the manuals.

˜ This manual includes a number of symbols that are intended to help you use the product safely, to prevent harm to you and others, and to protect against damage to property. These symbols and their meanings are listed below. Make sure you fully understand these symbols before you begin reading the main text.

Explanations of Injury and Damage That May Result from Incorrect Use

Warning

Caution

Ignoring the content marked by this indication and using the product incorrectly is expected to lead to death or serious injury.

Ignoring the content marked by this indication and using the product incorrectly is only expected to lead to injury or property damage.

Types of Precautions

Forbidden

Indicates actions that are forbidden (must not be performed)

Indicates that disassembly is forbidden.

Forbidden

Mandatory

Indicates actions that are mandatory (must be performed)

Marks content that should receive your full attention.

Warning

Do not disassemble or modify the product.

Doing so could lead to an accident, fire, or electric shock.

Store screws and other small objects where children cannot reach them. If one of those small objects is swallowed, consult with a doctor immediately.

Forbidden

When replacing fuses be sure to

use the fuses with the specified current

rating. Failing to do so could lead to

an accident or fire.

Mandatory Forbidden

Only connect the product to a 12 VDC negative ground car. Failing to do so could lead to an accident or fire.

Mandatory

Since this vehicle has two batteries, disconnecting the battery is not a good option. Take caution when testing circuits. Failing to do so could lead to electric shock or injury.

Do not cut the insulation on a cord and take power from another device. Doing so could lead to fire or electric shock.

Do not install the product in a location where it willl obstruct the driver’s forward view; interfere with the operation of the steering wheel, gear shift, or the like; or pose a threat to passengers. Doing so could lead to an accident or injury.

Forbidden

Forbidden

Jeep Wrangler i407-WRA-JL 20210330v1 ˜ 2/22

When making a hole in the vehicle body, be careful to avoid damaging pipes, the fuel tank, electrical wiring, and the like. This kind of damage could lead to an accident or fire.

When installing and grounding the product, do not use any of the bolts or nuts of the steering wheel, brakes, fuel tank, or the like. Doing so could make the brakes stop working or could lead to fire.

Forbidden

Do not install the product near the passengerside airbag. Doing so could interfere with the operation of the airbag and lead to an accident or injury.

Forbidden

Bundle cords so that they don’t interfere with driving. Wrapping cords around the steering wheel, gearshift, brake pedal, or the like could lead to an accident or damage equipment.

Caution

Connect the product properly according to the instructions. Failing to do so could lead to fire or an accident.

Forbidden

Do not sandwich cords between the seat railing or allow them to touch protrusions. Resulting breaks or shorts could lead to electric shock or fire.

Do not block vents or heat sinks. Doing so could lead to fire or damage equipment.

Use the accessories according to the instructions, and attach them securely. Failing to do so could lead to an accident or damage equipment.

Forbidden

Do not install the product where it may be exposed to water or in a place with high levels of humidity or dust. Doing so could lead to fire or damage equipment.

Forbidden

The installation and wiring of this product requires specialized skills and experience. Have the product installed by an Alpine authorized dealer.

Tools Required

Wire Strippers

Wire Cutters

8mm Socket

Jeep Wrangler i407-WRA-JL 20210330v1 ˜ 3/22

7mm Socket

Extension Ratchet

#2 Phillips Screwdriver

Digital Multimeter

Torx T20

Cordless Power Drill

Panel Removal Tools

Accessory List

iLX-407 Head Unit Dash Kit

Jeep Wrangler i407-WRA-JL 20210330v1 ˜ 4/22

Mounting Brackets

Maestro Module Camera/Preout Harness Main Harness

External Bluetooth Mic FM/AM Antenna Adapter USB, HDMI, Aux Interface

Chime Speaker Documents

OM QR Card

Alpine

Registration Card

Installation

Manual

Jeep Wrangler i407-WRA-JL 20210330v1 ˜ 5/22

Accessory List Continued

Round Head Screws M5#8 (4pcs) Maestro Flashing Cable USB

Micro To Full Size

SiriusXM Radio Antenna Adapter

(only for vehicles with factory

SiriusXM)

Mini USB To USB For Center

Console Power

USB Power Adapter Camera Male To Male RCA

Coupler (Not Used)

Camera Power Harness Camera Module

LVDS IN

FACTORY CAMERA BSV INTERFACE

SGS-BSV1-WJL

USB Flash

UP=Wrangler

DIP1:

Down=Gladiator

DIP7:

All up

DIP 2,3,4,5,6,7,8

Down=Firmware Update

VIDEO OUT

Power & CAN

IN

Can1

Can2

Rear Camera RCA

Jeep Wrangler i407-WRA-JL 20210330v1 ˜ 6/22

Factory Unit Disassembly Process

1

As a precautionary measure it’s a good idea to mask out the dashboard and panels to prevent scratches.

2

Unsnap the 6 clips and loosen the knee panel under the steering wheel using a panel removal tool.

3

Unsnap 10 clips, unplug the 2 harnesses, and remove HVAC panel using a panel removal tool.

4

Use #2 Phillips Screwdriver to extract (2) screws from the bottom of the radio bezel.

5

Unsnap 6 clips and remove radio bezel using a panel removal tool.

6

This shows where all the OEM clips are at to remove for step 5.

Jeep Wrangler i407-WRA-JL 20210330v1 ˜ 7/22

Factory Unit Disassembly Process (Continued)

7

Use #2 Phillips Screwdriver to extract (4) screws from head unit. Disconnect and remove the radio.

8

Disconnect the harnesses behind the OEM head unit.

9

The disconnected harnesses from the previous step. These will be used later to connect to the main harness in the installation.

10

Open the glove compartment and remove all contents, push up the glove compartment travel stop and lower the door, pivot the glove compartment downward, release latch on left side of the glove compartment by pushing it upward, pull the glove compartment upward to remove it from the pivot.

Jeep Wrangler i407-WRA-JL 20210330v1 ˜ 8/22

Factory Unit Disassembly Process (Continued)

12

Remove the A pillar by removing the (2) 8mm screws and unclipping the panel. The screws can be exposed using a panel removal tool.

13

Loosen the clips around the top panel visor area.

14

Unclip 7 clips and remove the center media stack.

Jeep Wrangler i407-WRA-JL 20210330v1 ˜ 9/22

Installation Instructions

1

Mount the microphone next to the rear view mirror and run the cable behind the factory panels. Route as shown on the diagram on page 12.

2

Run the Bluetooth microphone cable down the A pillar along the OEM wiring. Route as shown on the diagram on page 12.

3

Route vehicle cable in main harness from radio cavity to glove box and connect it to OBDII gateway behind the glove box. If the gateway is fully occupied, unclip 1 connector from it and use

T-harness.

4

At radio cavity, connect the main harness, white FM adapter, and green SiriusXM antenna, and other adapters to factory harness and secure them.

Jeep Wrangler i407-WRA-JL 20210330v1 ˜ 10/22

Installation Instructions (Continued)

5

If the vehicle has an OEM amplifier the KCX-

F200INT will need to be purchased separately.

This has 30” of cable so it can be routed behind the glovebox. It is important to do this so it can disappate heat properly. The audio settings will also need to be set to flat as shown on page 20.

6

Connect the camera interface module to the violet or red factory camera plug and put it in right side of radio cavity. Dip switch 1 will need to be moved down for the Gladiator JT.

7

Attach the Maestro to the main harness and tuck it in left side of radio cavity.

8

Run chime speaker harness from Maestro module to behind the glove box and attach there.

9

Remove the OEM USB from the Center Media panel by unclipping the clips on the sides.

10

Insert the X409 USB HDMI box into the OEM

Center Media panel.

Jeep Wrangler i407-WRA-JL 20210330v1 ˜ 11/22

Installation Instructions (Continued)

11

Plug in the OEM USB and the USB from the box to the power adapter. The adaptor needs to be plugged into the BLACK micro usb.

12

WARNING: There are 2 factory micro USB plugs in the dash behind the media center. One is black and one is grey. If the supplied adaptor is plugged into the grey micro USB the factory USB’s will not charge. When it is plugged into the black plug all rear USB’s can be used for charging (not data).

Correct

13

Attach the head unit to the mounting brackets using the (4) M5X8LMM supplied screws.

Incorrect

14

Connect the main harness, microphone, USB,

HDMI, FM adapter, and other harnesses to the iLX-

407 head unit and secure them. Mount the head unit to the dash using the (4) OEM screws removed in step 9 of the disassembly.

15

Clip in the dash kit and seecure the it using the two screws removed in step 4 of the disassembly.

Reinstall the rest of the factory panels to complete the installation.

Jeep Wrangler i407-WRA-JL 20210330v1 ˜ 12/22

Component Locations

IMPORTANT: Follow the recommended component location shown below. Failure to do so, will result in poor

GPS performance.

Add-on Microphone

SAT-Radio Tuner

(Sold Separately) iDatalink Maestro Module

OEM Camera Module

OBDII Gateway

/////alpine

3

4

2

1

5

0

6 7

RPM

X1000

Jeep

30

40

50

20

10

0

MPH

ENGINE

STOP

AUDIO

MENU CAM

NAV

MEDIA

Connection Of An External Amplifier

ANTENNA

VIDEO IN/OUT

USB

HDMI IN

CAN I/F

CAMERA/PRE OUT

MIC SWC SXM/DAB

POWER

SUBW

Note: If the sub output is used it will need to be turned on the the sound settings.

FRONT OUT

(Blue/White) REMOTE

(Red)

(White)

(Red)

(White)

(Red)

REAR OUT

(White)

RCA Extension Cable (sold separately)

Remote Turn-On Lead (Blue/White)

Subwoofer RCA Connectors

Front Output RCA Connectors

Rear Output RCA Connectors

REMOTE ON

(Blue/White)

REMOTE ON

(Blue/White)

Amplifier for subwoofer

(sold separately)

To subwoofer input terminal

Subwoofer

To front input terminal

Amplifier 4 ch

(sold separately)

To rear input terminal

Front speaker

Rear speaker

Jeep Wrangler i407-WRA-JL 20210330v1 ˜ 13/22

Connecting A SiriusXM Module (Sold Separately)

There is no way to integrate the factory SiriusXM tuner. Once the radio is removed, the factory SiriusXM is removed. As the title states, SiriusXM requires a tuner sold separately. This diagram shows how to integrate the antenna connection. For vehicles with factory SiriusXM connect the adapter to the factory SiriusXM antenna in the radio cavity. The factory SiriusXM antenna is located on the passenger side B-pillar. For vehicles without factory SiriusXM use the antenna that is included with the SXV300 SiriusXM Tuner.

VIDEO IN/OUT

USB

HDMI IN

ANTENNA

CAN I/F

CAMERA/PRE OUT

MIC SWC SXM/DAB

POWER

Connection Of Optional Front Camera

iLX-407 Source Unit

USB

HDMI IN

VIDEO IN/OUT

ANTENNA

AUX Power

3-pin Black Connector

Yellow- 12V+

Constant Not Used

Black- Ground

Red- Acc 12V+

Optional Front Camera

This is a generic example of a typical front camera installation. Refer to your front camera installation manual for specifics on how it works.

CAN I/F

CAMERA/PRE OUT

Front Camera

Input

MIC SWC

SXM/DAB

POWER

i407-WRA-JL Wiring Diagram Continued

To Vehicle Connectors

FM

Antenna

(White)

Power

Speaker

52-pin Connector

AMPLIFIED VEHICLES

WARNING!

Jeep Wrangler i407-WRA-JL 20210330v1 ˜ 14/22

SXM

Antenna

(Green)

Only 2 connections are necessary for the OEM amplified system. Front

(White) connects to Front

(White) from tuner. Rear

(Black) connects to Rear

(Black) towards the vehicle.

The other two connections are not used.

X

X

Do not plug this into the

VIDEO

IN/OUT.

ANTENNA iLX-407

USB

CAN I/F

CAMERA/PRE OUT

HDMI IN

VIDEO IN/OUT

MIC SWC

SXM/DAB

POWER

To Bluetooth Mic Input

Power Harness

AUX Input

Black

Not

Used

10-Pin Chime 18-Pin

Red

Not

Used

Reset

Button

Optional

SiriusXM Tuner

(Sold Seperately)

Main Harness iDatalink MAESTRO Module

Chime Speaker

3-Pin

Black

Not

Used

Blue

Not

Used

4-Pin 10-Pin 3-Pin 4-Pin

CAN pass through connection in case bank is

full. Otherwise not used.

Rear

Camera

(Violet or Red)

VIDEO OUT

LVDS IN

Dip Switch 1 should be up for the Wrangler and down for the Gladiator. The rest of the switches are not used.

USB Flash

Down=Firmware Update

DIP7:

All up

DIP 2,3,4,5,6,7,8

FACTORY CAMERA BSV INTERFACE

SGS-BSV1-WJL

Power & CAN

IN

Can1

Can2

Down=Gladiator

UP=Wrangler

DIP1:

Blue Power Antenna

Blue/White Amp Turn-on

To CAN Connector

CAN Connector Bank

Aux Power pass through covered by protective cap

Aux Power

USB, AUX, HDMI Interface

Rear Camera Video Output RCA

USB

HDMI

Aux Input

To Center Console USB Power connector in vehicle

This must be plugged into the black micro USB. See page 16 for details

USB Power

Mini USB To USB

FM

Antenna

(White)

Power

Speaker

52-pin Connector

To Vehicle Connectors

AMPLIFIED VEHICLES

WARNING!

Only 2 connections are necessary for the OEM amplified system. Front

(White) connects to Front

(White) from tuner. Rear

(Black) connects to Rear

(Black) towards the vehicle.

The other two connections are not used.

X

X

SXM

Antenna

(Green)

Do not plug this into the

VIDEO

IN/OUT.

ANTENNA iLX-407

USB

CAN I/F

CAMERA/PRE OUT

HDMI IN

VIDEO IN/OUT

MIC SWC

SXM/DAB

POWER

To Bluetooth Mic Input

Power Harness

AUX Input

Jeep Wrangler i407-WRA-JL 20210330v1 ˜ 15/22

i407-WRA-JL Wiring Diagram Continued

Black

Not

Used

10-Pin Chime 18-Pin

Red

Not

Used

Reset

Button

Optional

SiriusXM Tuner

(Sold Seperately)

Main Harness iDatalink MAESTRO Module

Chime Speaker

3-Pin

Black

Not

Used

Blue

Not

Used

4-Pin 10-Pin 3-Pin 4-Pin

CAN pass through connection in case bank is

full. Otherwise not used.

Rear

Camera

(Violet or Red)

VIDEO OUT

LVDS IN

Dip Switch 1 should be up for the Wrangler and down for the Gladiator. The rest of the switches are not used.

USB Flash

Down=Firmware Update

DIP7:

All up

DIP 2,3,4,5,6,7,8

FACTORY CAMERA BSV INTERFACE

SGS-BSV1-WJL

Power & CAN

IN

Can1

Can2

Down=Gladiator

UP=Wrangler

DIP1:

Blue Power Antenna

Blue/White Amp Turn-on

To CAN Connector

CAN Connector Bank

Aux Power pass through covered by protective cap

Aux Power

USB, AUX, HDMI Interface

Rear Camera Video Output RCA

USB

HDMI

Aux Input

To Center Console USB Power connector in vehicle

This must be plugged into the black micro USB. See page 16 for details

USB Power

Mini USB To USB

i407-WRA-JL Wire Descriptions

CAN Interface Connector (included)

USB extension cable (included)

VIDEO IN

VIDEO OUT

VIDEO IN/OUT cable

REMO

(Blue/White)

REVERSE

(Orange/White)

P. ANT

(Blue)

PARKING BRAKE

(Yellow/Blue)

ACC

(Red)

BATT

(Yellow)

GND

(Black)

PRE OUT cable

Power cable

AUX INPUT

REAR VIEW CAMERA

FRONT VIEW CAMERA

(Green)

(Green/Black)

(White)

(White/Black)

(Gray/Black)

(Gray)

(Violet/Black)

(Violet)

SUBW

FRONT OUT

REAR OUT

Jeep Wrangler i407-WRA-JL 20210330v1 ˜ 16/22

Vehicle Antenna

To Interface Box

To USB flash drive, iPhone or

Android smartphone

Microphone (included)

To drive recorder, DVD player, etc.

To Rear monitor

To amplifier or equalizer

To plus side of the back lamp signal lead of the car

To power antenna

To the parking brake signal lead

Ignition key

Battery

Rear Left

Front Left

Front Right

Rear Right

Speakers

To AUX output device

To RCA Rear camera

To RCA Front camera

To input terminal of amplifier when adding an external amplifier

Jeep Wrangler i407-WRA-JL 20210330v1 ˜ 17/22

i407-WRA-JL HDMI Usage With An iPhone

Do not use the head unit’s

USB to power HDMI devices.

This port is meant for Apple

CarPlay, Android Auto, and

USB flash drives.

Do not use the head unit’s

USB to power HDMI devices.

This port is meant for Apple

CarPlay, Android Auto, and

USB flash drives.

ANTENNA

For all phones the USB power source needs to be a 2A source. This will require a separate USB power source to be installed in the vehicle.

power source needs to be a 2A source. This will require a separate USB power source to be installed in the vehicle.

USB

USB

CAN I/F

HDMI IN iLX-407 Source Unit

VIDEO IN/OUT iLX-407 Source Unit

VIDEO IN/OUT

HDMI IN

MIC SWC SXM/DAB

CAN I/F

CAMERA/PRE OUT

Lightning To HDMI adapter needs to be purchased from Apple.

Third party adapters may not work

Lightning To HDMI adapter needs to be purchased from Apple.

Third party adapters may not work

MIC SWC SXM/DAB

POWER iPhone

POWER iPhone

i407-WRA-JL HDMI Usage With An Android Phone

Do not use the head unit’s

USB to power HDMI devices.

This port is meant for Apple

CarPlay, Android Auto, and

USB flash drives.

USB to power HDMI devices.

ANTENNA

This port is meant for Apple

CarPlay, Android Auto, and

Or

Or have the ability to cast the easiest way to connect is with a Miracast adapter (for example a Roku Stick or Amazon Firestick). have the ability to cast the easiest way to connect is with a Miracast adapter (for example a Roku Stick or Amazon Firestick).

For all phones the USB power source needs to be a 2A source. This will require a separate USB power source to be installed in the vehicle.

be a 2A source. This will require a separate USB power source to be installed in the vehicle.

USB

USB

CAN I/F

CAN I/F

CAMERA/PRE OUT

CAMERA/PRE OUT iLX-407 Source Unit

VIDEO IN/OUT

HDMI IN iLX-407 Source Unit

VIDEO IN/OUT

HDMI IN

MIC SWC

MIC SWC

Android Phone

Android Phone

Some Android phones may have a HDMI adapter. That would be sold separately by the phone manufacturer. Third party adapters will not work.

have a HDMI adapter. That would be sold separately by the phone manufacturer. Third party adapters will not work.

SXM/DAB

SXM/DAB

POWER

POWER

Jeep Wrangler i407-WRA-JL 20210330v1 ˜ 18/22

Wire Harness Pin Outs

Radio Main

5

4

3

2

1

8

7

6

16

15

14

13

12

11

10

9

Blue 22AWG

Red 20AWG

Blue/White 22AWG

Orange/White 22AWG

Yellow/Blue 22AWG

Purple 20AWG

Gray 20AWG

Purple/Black 20AWG

Gray/Black 20AWG

Green 20AWG

White 20AWG

Green/Black 20AWG

White/Black 20AWG

Yellow 18AWG

Black 18AWG

Radio I/O

9 10

7 8

5

3

1 2

6

4

Blue/White 22AWG

Yellow/Blue 22AWG

Orange/White 22AWG

CAN I/F

9 10

7 8

5 6

3 4

1 2

Red 22AWG

Blue 22AWG

Black 22AWG

White 22AWG

Camera Power

1

2

Red 20AWG

Black 20AWG

Rear Camera

5

3

1

6

4

2

Black 22AWG

Yellow/Black 22AWG

Red 22AWG

Orange/White 22AWG

Orange 22AWG

Aux Power

3

2

1

Yellow 18AWG

Red 20AWG

Black 18AWG

Data SWC

17 18

15 16

13 14

11 12

9 10

7

5

3 4

1 2

8

6

Wrangler Radio

52

51

50

49

40

39

38

37

36

35

34

33

32

31

23

22

21

26

25

24

30

29

28

27

48

47

46

45

20

19

10

9

18 8

17 7

16

15 5

14 4

6

13 3

12 2

11 1

44

43

42

41

Red/Brown 22AWG

Yellow/Brown 22AWG

Brown/Red 22AWG

Brown/Yellow 22AWG iDatalink

4

3

2

1

Blue 22AWG

White 22AWG

Black 22AWG

Red 22AWG

Green/Black 20AWG

Green 20AWG

Yellow 18AWG

White/Black 20AWG

Black 18AWG

White 20AWG

Gray 20AWG

Gray/Black 20AWG

Purple 22AWG

Purple/Black 22AWG

Brown/Yellow 20AWG

Brown/Red 20AWG

Speaker Harness

3

4

1

2

Speaker Harness

3

4

1

2

CAN

1

2

Purple 20AWG

Purple/Black 20AWG

Green 20AWG

Green/Black 20AWG

Gray 20AWG

Gray/Black 20AWG

White 20AWG

White/Black 20AWG

Brown/Red 22AWG

Brown/Yellow 22AWG

Maestro Power

3

2

1

Yellow 18AWG

Red 20AWG

Black 18AWG

CAN Connector

2

1

Yellow/Brown 22AWG

Red/Brown 22AWG

CAN Connector

2

1 Red/Brown 22AWG

Yellow/Brown 22AWG

Steering Wheel Configuration

Jeep Wrangler i407-WRA-JL 20210330v1 ˜ 19/22

Off Hook

Voice

On Hook

Seek Up

Preset Up

Seek Down

OK

Volume Up

Source

Volume Down

Button

Seek Up

Seek Down

Next Preset

Voice

Off Hook

On Hook

Volume Up

Volume Down

Source

Press Once

Track +

Track -

Preset & Folder +

Voice Or Siri

Answer Call

Hang Up & Reject Call

Volume +

Volume -

Source/Camera View

Press And Hold

None

None

Preset & Folder -

None

None

None

None

Attenuation On/Off

None

Jeep Wrangler i407-WRA-JL 20210330v1 ˜ 20/22

Set Up Guide

1

Turn the vehicle’s Ignition switch to ACC.

2

Turn ON the i407-WRA-JL by pressing any key.

3

With the vehicle parked, engage the parking brake, release the parking brake and engage the parking brake again.

4

If a rear camera is present, turn it ON in the settings menu. (HOME/SETTINGS/CAMERA/REAR CAMERA/

CAMERA SELECT/REAR/OK).

5

If a front camera is present, turn it ON in the settings menu. (HOME/SETTINGS/CAMERA/FRONT CAMERA/

CAMERA SELECT/FRONT/OK).

6

If the AUX Input is being use be sure to turn it ON in the settings. (HOME/SETTINGS/GENERAL/AUX/AUX

SELECT).

7

Vehicle information- Set the desired gauge information. (HOME/SETTINGS/GENERAL/IDATALINK).

8

For vehicles with an OEM amplifier the Time Correction, P-EQ, and X-Over must be set flat. (HOME/

SETTINGS//SOUND).

Detailed descriptions of the settings can be found in the owners manual which can be downloaded from the support page of the website.

Retained Features

STEERING WHEEL CONTROLS

Two Functions on Each Button

Standard and Expanded Radio Functions

NAVIGATION OUTPUTS

Accessory Power Output (15A)

Parking Brake Output

Reverse Light Output

Vehicle Speed Pulse Output

Foot Brake Output

FACTORY AMPLIFIER

Amplifier Turn on

Speed Compensated Volume (Premium Audio)

Digital Fader (Premium Audio)

DSP Settings (Premium Audio)

Gain Adjustment (Premium Audio)

SECONDARY VEHICLE DISPLAY (IF EQUIPPED)

Audio Information Display

Hands Free Info Display

Navigation Info Display

VEHICLE SETTINGS

Access And Modify Vehicle Settings

ADVANCED CAMERA FEATURES

Front Camera Auto Control (Not Retained)

CLIMATE CONTROL

Climate Display And Control On Radio

GAUGES

Selectable Performance Gauges

“Track Pack” Gauges

Read/Reset Check Engine Codes

PARK ASSIST

Retain Parking Assist Chimes

Distance Display On Screen

VEHICLE INFO

Tire Pressure Display

Battery Voltage Display

Read/Reset Check Engine Codes

Door open Status and Warning

ACCESSORIES

OEM Accessory Control Integration

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

X

■

■

■

■

■

■

■

■

■

■

■

Jeep Wrangler i407-WRA-JL 20210330v1 ˜ 21/22

Troubleshooting Guide

1

2

3

4

5

6

7

8

Symptom iPhone not working with

HDMI.

Possible Cause

Not using Apple HDMI to Lightning adapter.

Didn’t plug USB power into a 2A source.

Using incorrect HDMI adapter.

Android phone is not working with HDMI.

Miracast adapter isn’t plugged into a 2A source.

Miracast adapter has resolution settings that are too high.

iDatalink website says serial number is invalid.

No output from RCA’s

Navigation voices and/or

Bluetooth audio can’t be heard.

Incorrect serial number is being used.

Serial number may not be in iDatalink database.

Maestro module is flashed for amplified system.

The vehicle has an OEM amplifier and the warning on page 14 was not followed.

Maestro module was not flashed.

Steering wheel controls aren’t working. Vehicle data isn’t displaying.

Connection was not made properly.

Headunit will not turn on.

Cannot enter SETTINGS

MENU.

One of the power wires does not have proper voltage

4 pin Maestro data cable is disconnected or damaged.

OBD2 cable is not plugged in.

Main harness is not connected.

Vehicle is in motion or parking brake is not engaged.

Remedy

Purchase the HDMI to Lightning adapter directly from Apple. Not all 3rd party adapters work the same.

Do not plug into the USB from the Alpine head unit. A third party USB adapter will need to be used that is 2A.

If the phone has the feature to use an HDMI adapter it must be the one purchased from the manufacturer of the phone, not a third party adapter.

Do not plug into the USB from the Alpine head unit. A third party USB adapter will need to be used that is 2A.

Plug the adapter into another monitor (for example a television in the home) and reduce the resolution settings.

In the i407-WRA settings confirm the serial number. HOME/SETTINGS/GENERAL/

ABOUT/VERSION INFORMATION.

Call ADS at 1-866-427-2999 and verify.

Re-flash module for non-amplified system.

Swap the front and rear speaker connectors as shown on page 14.

Flash the maestro module as shown on page

5.

Every harness needs to be plugged into it’s proper place. Follow pages 14 and 15 and ensure every connection is going exactly where it needs to be. Make sure the CAN

IF connector did not get plugged into the

VIDEO IN/OUT port accidentally.

Test the power wires with a digital multimeter and trace from there.

Check for proper connection or disconnected pins.

Connect OBD2 connector to the OBD2 port.

Check for proper connection or disconnected pins.

With vehicle in (P)PARK engage the parking brake. Release the parking brake and engage the parking brake a second time, as shown in the Setup Guide on page 20.

Jeep Wrangler i407-WRA-JL 20210330v1 ˜ 22/22

Troubleshooting Guide Continued

9

10

11

12

13

14

15

16

Only the front speakers are on for SXM Radio.

SXM Tuner has not been activated.

Activate SXM Tuner.

iPhone or Android phone is not recognized when connected to the

USB cable, causing CarPlay or Android Auto to not function.

Rear camera not automatically coming on when vehicle is in reverse.

Front camera image is reversed.

Installed an amplifier and it only gets sound on FM.

Can’t be heard when making phone calls.

OEM USB’s not charging.

Loose or disconnected USB cable.

Non-compatible cable.

Wrong USB port used.

The rear camera was not turned on in the setup menu.

Rear camera just shows blank image with guide cones.

The rear camera is not outputting an image.

A front camera was not used.

The power antenna wire was used instead of the remote wire.

Check the USB connection behind the headunit.

Use the cable supplied with the iPhone or Android phone and only plug into the extension provided with the head unit.

Third party adapters like flush mount, OEM integration, and/or long extensions may not work. Only use USB extension that came with the head unit.

The OEM USB’s are only meant for charging.

They can’t transfer data. The only one that can is the bottom port of the USB, AUX,

HDMI interface that is included.

Refer to Step 4 of the Set Up Guide on page

20.

Refer to page 15 and ensure all the connections are made exactly as shown and the dip switches are in the correct positions.

A known good RCA source can be used into the head unit to let you know if the head unit is receiving the video signal and let you know if it’s a connection on the camera side or going to the head unit.

A rear camera can not be used for the front of the vehicle. It will not display the image correctly and it will be reversed.

The remote wire is what needs to be connected to the remote turn on lead of the amplifier.

The microphone is not plugged into the correct port.

The wrong micro USB was plugged into the USB power adapter.

The microphone needs to be plugged into the port labeled “MIC”. If it gets plugged into the SWC port it will not function properly.

Page 14 shows the correct port to plug into.

There are 2 factory micro USB plugs in the dash behind the media center. One is black and one is grey. If the supplied adaptor is plugged into the grey micro

USB the factory USB’s will not charge.

Make sure the black USB is plugged into the power adapter. See page 11 for details.