MultiBio700 User Manual
MultiBio700 User Manual
Version: 1.1
Date: Nov. 2010
About This Manual
This document introduces the user interface and menu operations of
MultiBio700. For installation, please refer to the Installation Guide.
Table of Contents
Table of Contents
1. Instructions for Use......................................................................1
1.1 Standing Position, Posture and Face Expressions...................1
1.2 Enrollment Face Expressions ...................................................2
1.3 Finger Placement......................................................................3
1.4 Use of the Touch Screen ..........................................................4
1.5 Touch Operations......................................................................5
1.6 Appearance of Device...............................................................7
1.7 Main Interface ...........................................................................8
1.8 Verification Modes...................................................................10
1.8.1 Fingerprint Verification .....................................................10
1.8.2 Face Verification...............................................................12
1.8.3 Password Verification.......................................................14
1.8.4 ID Card Verification ★.....................................................15
1.8.5 Combination Verification ★.............................................16
2. Main Menu ...................................................................................18
3. Add User ......................................................................................20
3.1 Entering a User ID ..................................................................21
3.2 Entering a Name .....................................................................22
3. 3 Enrolling a Fingerprint............................................................23
3. 4 Enrolling a Password .............................................................25
3. 5 Enrolling a Face .....................................................................26
3.6 Entering a Group No...............................................................27
3.7 Modifying User Rights.............................................................29
3.8 Enroll Photos...........................................................................30
3.9 User Access Settings ..............................................................31
I
MultiBio700 User Manual
3.10 Enrolling an ID card ★.........................................................34
4. User Management.......................................................................35
4.1 Edit a User ..............................................................................36
4.2 Delete a User ..........................................................................37
4.3 Query a User...........................................................................38
5. Communication Settings ...........................................................39
5.1 Network Settings.....................................................................40
5.2 Wiegand Output ......................................................................42
5.2.1 Wiegand 26-bits Output Description ................................43
5.2.2 Wiegand 34-bits Output Description ................................45
5.2.3 Customized Format..........................................................47
5.3 Wiegand Input.........................................................................51
6. System Configuration ................................................................52
6.1 General Parameters................................................................53
6.2 Interface Parameters ..............................................................54
6.3 Fingerprint Parameters ...........................................................55
6.4 Face Parameters ....................................................................57
6.5 Log Settings ............................................................................59
6.6 Keyboard Definitions...............................................................60
6.7 Access Settings.......................................................................61
6.7.1 Time zone setting .............................................................62
6.7.2 Holiday setting..................................................................63
6.7.3 Group time zone setting...................................................65
6.7.4 Unlock Combination Setting.............................................68
6.7.5 Access control parameter ................................................70
6.7.6 Duress Alarm Parameters................................................72
II
Table of Contents
6.7.7 Anti-Pass back setting......................................................73
6.8 Update ....................................................................................74
7. Data Management .......................................................................75
8. Date/Time Setting .......................................................................78
8.1 Set Date/Time .........................................................................78
8.2 Bell Setting ★ ........................................................................79
9. Auto Test......................................................................................81
10. USB Disk Management ............................................................84
11. System Information ..................................................................85
12. Appendix ...................................................................................86
Appendix 1 T9 Input Instructions ..................................................86
Appendix 2 Introduction of Wiegand.............................................88
Appendix 3 Photo ID Function ......................................................90
Appendix 4 Multi-combination Authentication Mode ★ ...............92
Appendix 5 Anti-Pass Back ★ .....................................................96
Appendix 6 Statement on Human Rights and Privacy..................99
Appendix 7 Environment-Friendly Use Description ....................101
1. Instructions for Use
1. Instructions for Use
1.1 Standing Position, Posture and Face Expressions
1. Recommended standing-distance from device:
For users 5-6 feet tall (1.5m-1.85m) we recommend
users stand about 2 feet (0.5m) from the wall.
When viewing your image on the device display
window, step away if your image appears too bright.
Step closer if your image appears too dark.
2. Recommended face Expressions vs. poor
Expressions:
3. Recommended Posture (pose) vs. poor Posture (pose):

Note: During enrollment and verification, try to have a relaxed
1
MultiBio700 User Manual
unstrained face expression and stand upright.
1.2 Enrollment Face Expressions
During the enrollment, position your head such way that your face appears in
the center of the device display window. The device will prompt you how to
move your head.
Follow the voice prompts by first gently turning your head left, then right.
Then your head gently down, then up, and so on. The slight variations of the
head angles will help the device to better recognize your face when you
attempt to verify.
The enrollment face experssions as follows:
Look ahead
Look at screen
Bow down
Turn left
Turn
2
1. Instructions for Use
1.3 Finger Placement
Recommended fingers: The index finger, middle finger or the ring finger is
recommended; the thumb and little finger are not recommended (because
they are usually clumsy when pressing on the fingerprint collection screen).
1. Proper finger placement:
The finger must be flat to the surface
and centered on the fingerprint
sensor.
2. Improper finger placement:
Not flat to the surface
Slanting
Off-center
Off-center
Please enroll and verify your fingerprint by using the proper finger placement
mode. We shall not be held accountable for any consequences arising out of the
degradation in verification performance due to improper user operations. We shall
reserve the right of final interpretation and revision of this document.
3
MultiBio700 User Manual
1.4 Use of the Touch Screen
Touch the screen with one of your fingertips or the edge of a fingernail, as
shown in the following figure. A broad point of contact may lead to inaccurate
pointing.
When the touch screen is less sensitive to the touch, you can perform a
screen calibration through the following menu operations. Press [Menu] ->
[Auto Test] -> [Calibration] on the screen and a cross icon will be displayed.
After you touch the center of the cross at five locations on the screen correctly,
the system will automatically returns to the main menu. Press [Exit] to return
to the initial interface. For details, see the description in 9. Auto Test.
Smear or dust on the touch screen may affect the performance of the touch
screen. Therefore, try to keep the screen clean and dust-free.
4
1. Instructions for Use
1.5 Touch Operations
1. Enter numbers: Press the [User ID] key. The system will automatically
display the number input interface. After entering the user ID, press [OK] to
save or press [X] to cancel and return to the previous interface.
2. Enter Text: Press the [Name] key. The system will automatically display
the text input interface. After entering the user name, press [X] to save and
return to the previous interface.
5
MultiBio700 User Manual
3. Modify parameters: Press the default value of a parameter and the
system will automatically switch to another value of this parameter.
6
1. Instructions for Use
1.6 Appearance of Device
1. Front View
LED Indicator
Touch Screen
Touch keys
Camera
Push Buttons
Fingerprint Sensor
2. Side View
ID Card Swipe Area
Reset Button
USB Port
7
MultiBio700 User Manual
1.7 Main Interface
 Date
 Screen Shortcut
 Time
 Attendance Status
 Face Image
 1:1 Switch Key
 Menu
1:1
 1:1 Switch button
 Door Bell
① Date: The current date is displayed.
② Screen Shortcut Keys: Press these shortcut keys to display the
attendance status. Users can customize the function of each shortcut key.
For details, see 6.6 Keyboard Definitions.
③ Time: The current time is displayed. Both 12-hour and 24-hour time
systems are supported.
④ Attendance Status: The current attendance status is displayed.
⑤ Fingerprint Image: When the fingerprint image is displayed, the device is
8
1. Instructions for Use
currently in the fingerprint recognition mode.
⑥ 1:1 Switch Key: By pressing this key, you can switch to the 1:1 verification
modes, and enter the digital input interface. The function is same to ⑨[1:1]
Switch Button.
⑦ Menu: You can enter the main menu by pressing this key.
⑧ Door Bell: For visitors to ring the bell and ask for help to open the door.
⑨ 1:1 Switch Button: By pressing this button, you can enter the digital input
interface of the 1:1 verification mode.
9
1. Instructions for Use
1.8 Verification Modes
1.8.1 Fingerprint Verification
1. 1: N fingerprint verification
In this fingerprint verification mode, the device
compares current fingerprint collected by the
fingerprint sensor with all fingerprint data on the
device.
1. The default main interface is the fingerprint
verification mode. See the figure on the right.
2. Press your finger on the fingerprint sensor by
adopting the proper finger placement. For details,
see 1.3 Finger Placement.
3. If the verification is successful, the device will
prompt “Verified”.
4. If the verification is not successful, the device will prompt “Please try
again”.
10
1. Instructions for Use
2. 1:1 fingerprint verification
In the 1:1 fingerprint verification mode, the device
compares current fingerprint collected through the
fingerprint sensor with that in relation to the user ID
entered through the keyboard. Adopt this mode only
when it is difficult to recognize the fingerprint.
1. Press [1:1] on the screen or [1:1] button to enter
the 1:1 fingerprint recognition mode.
2. Enter user ID and then press the "Fingerprint”
icon to enter the 1:1 fingerprint recognition mode. If
the prompt “Unregistered user!” is displayed, the
user ID does not exist.
3. Press your finger on the fingerprint sensor by adopting the proper finger
placement. For details, see 1.3 Finger Placement.
4. If the verification is successful, the device will prompt “Verified”, otherwise
the device will prompt “Please try again”.
11
MultiBio700 User Manual
1.8.2 Face Verification
1:1 face verification
In the 1:1 face verification mode, the device
compares current face collected through the
camera with that in relation to the user ID entered
through the keyboard. Adopt this mode only when it
is difficult to recognize the face.
1. Press [1:1] on the screen or [1:1] button to enter
the 1:1 recognition mode.
2. Enter user ID and then press the "1:1 Face” icon
to enter 1:1 face recognition mode. If the prompt
“Unregistered user!” is displayed, the user ID does
not exist.
3. Compare the face in a proper way. For details, see 1.1 Standing Position,
Posture and Face Expression.
4. If the verification is successful, the device will prompt “Verified”. The
system will return to the main interface if the verification is not passed within
20 seconds.
12
1. Instructions for Use
13
MultiBio700 User Manual
1.8.3 Password Verification
In the password verification mode, the device
compares the password entered with that in relation
to the user ID.
1. Press [1:1] on the screen or [1:1] button to enter
the password verification mode.
2. Enter the user ID and then press the "Key” icon to
enter the password verification mode. If the prompt
“Unregistered user!” is displayed, the user ID does
not exist.
3. Enter the password and press the “OK” icon to
start the password comparison.
4. If the verification is successful, the device will prompt “Verified”, otherwise
the device will prompt “Verify fail” and return to password input interface.
14
1. Instructions for Use
1.8.4 ID Card Verification ★
 Note: Only the products with the built-in ID
card module support the ID card verification.
In the fingerprint verification mode, the device
compares current ID card collected by the Card
Reader with all the ID card data on the device.
1. Swipe your ID card on the card swipe area by
adopting the proper way. For the card swipe area,
see 1.6 Appearance of Device.
3. If the verification is successful, the device will
prompt “Verified”.
4. If the verification is not successful, the device will prompt “Not Enrolled”.
15
MultiBio700 User Manual
1.8.5 Combination Verification ★
The
device
supports
up
to
20
verification
modes,
including
FACE&PIN/FP/RF/PW 、 FP&PW 、 FP&RF 、 FACE&FP 、 FACE&PW 、
FACE&RF、FP、PW、RF、FACE&PIN、FP/RF、PW/RF、FP/PW、PW&RF、
PIN&FP 、 FP&PW&RF 、 PIN&FP&PW 、 FP&RF/PIN 、 FACE&FP&RF 、
FACE&FP&PW
etc.
For
the
detail,
please
refer
to
Appendix
4
Multi-combination Authentication Mode.
 Note: RF means ID card verification. Only the products with the built-in
ID card module support the ID card verification.
Here is the combination verification operation; we will use the FACE&FP
verification for an example.
If you verify the fingerprint first and then the face, the operations are as
follows.
(1) The default main interface is the fingerprint verification mode, see the
figure below.
(2) Press your finger on the fingerprint sensor by adopting the proper finger
16
1. Instructions for Use
placement. For details, see 1.3 Finger Placement.
(3) If the verification is successful, the device will enter the 1:1 face
recognition mode. Compare the face in a proper way. For details, see 1.1
Standing Position, Posture and Face Expression.
(4) If the verification is successful, the device will prompt “Verified”. The
system will return to the main interface if the verification is not passed within
20 seconds.
Otherwise, the FACE&FP combination verification can perform such as FACE
(1: N) + FP, PIN + FACE (1:1) + FP, PIN + FP (1:1) + FACE etc. The operation
is similar to the procedure introduced before.
17
2. Main Menu
2. Main Menu
There are two types of rights respectively granted to two types of users: the
Ordinary users and administrators. Ordinary users are only granted the
rights of face, fingerprint, password or card verification, while administrators
are granted access to the main menu for various operations apart from
having all the privileges granted to ordinary users.
Press [Menu] on the initial interface to access the main menu, as shown in
the following figure:
The main menu includes nine sub menus:
Add User: Through this submenu, you can add a new user and input the
information on the device, including the user ID, name, fingerprint, face, card,
password, rights, group No. and user access.
User Mgt.: Through this submenu, you can browse the user information
stored on the device, including the user ID, name, fingerprint, face, card,
password, rights, group No. and user access. Here you can also add, modify
18
2. Main Menu
or delete a user’s information.
Comm.: Through this submenu, you can set related parameters for
communication between the device and PC, including the IP address,
gateway, subnet mask, baud rate, device No. and communication password.
System: Through this submenu, you can set system-related parameters,
including the basic parameters, interface parameters, fingerprint, face and
attendance parameters, Keyboard definitions, Access settings, firmware
update etc. to enable the device to meet the user’s requirements to the
greatest extent in terms of functionality and display.
Data Mgt.: Through this submenu, you can perform management of data
stored on the device, for example, deleting the attendance records, all data,
clear administrator, restore to factory settings and query records.
Date/Time: Through this submenu, you can set the alarm time and duration,
or set the Bell.
Auto Test: This submenu enables the system to automatically test whether
functions of various modules are normal, including the screen, sensor, voice,
face, keyboard, clock tests and screen calibration.
Dn/Upload: Through this submenu, you can download user information and
attendance data stored in the device through a USB disk to related software
or other fingerprint recognition equipment.
Sys Info.: Through this submenu, you can browse the records and device
information.
Any user can access the main menu by pressing the [Menu] key if the system
does not have an administrator. After administrators are configured on the device, the
device needs to verify the administrators’ identity before granting them access to the
main menu. To ensure device security, it is recommended to set an administrator
when using the terminal initially. For detailed operations, see 3.7 Modify User Rights .
19
3. Add User
3. Add User
Press [Add] on the [User Mgt.] interface to display
the [Add User] interface as shown below.
User ID: Enter a user ID. 1 to 9 digits user IDs are
supported by default.
Name: Enter a user name. 12 characters user
names are supported by default.
Fingerprint: Enroll a user’s fingerprint and the
device displays the number of enrolled fingerprints.
A user can enroll 10 fingerprints at maximum.
Password: Enroll a user’s password. The device
supports 1-8 digit passwords by default.
Face: Enroll a user’s face.
Group No.: Set the group that the user belongs to.
Valid group No.: 1-24.
Role: Set the rights of a user. A user is set to
ordinary user by default and can also be set to
administrator. Ordinary users are only granted
the rights of
face, fingerprint or password
verification, while administrators are granted
access to the main menu for various operations
apart from having all the privileges granted to
ordinary users.
Photo: Enroll a user’s photo. During user verification, the user’s photo is
displayed on screen.
User Access: Set the lock control and access control parameters.
20
3. Add User
3.1 Entering a User ID
The device automatically allocates an ID starting
from 1 for every user in sequence. If you use the ID
allocated by the device, you may skip this section.
1. Press [User ID] on the [Add User] interface to
display the user ID management interface.
 Tip: The user ID can be modified during
initial enrollment, but once enrolled, it cannot be
modified.
2. On the displayed keyboard interface, enter a user
ID and press [OK]. If the message “The user ID already exists!” is displayed,
enter another ID.
 Tip: The device supports 1 to 9 digits user
IDs by default. If you need to extend the length
of current user ID numbers, please consult our
commercial
representatives
or
technical
pre-sales.
3. After the user ID is entered, press [Save] to save
the current information and return to the previous
interface. Press [Exit] to return to the previous
interface without saving the current information.
21
MultiBio700 User Manual
3.2 Entering a Name
Use T9 input method to enter the user name
through the keyboard.
1. Press [Name] on the [Add User] interface to
display the name input interface.
2. On the displayed keyboard interface, enter a user
name and press [X].
For details of operations on the keyboard interface,
see Appendix 1 T9 Input Instructions.
3. After the user name is entered, press [Save] to
save the current information and return to the
previous interface. Press [Exit] to return to the previous interface without
saving the current information.
 Tip: The device supports the 1 to 12 characters names by default.
22
3. Add User
3. 3 Enrolling a Fingerprint
1. Press [Fingerprint] on the [Add User] interface to
display the [Enroll Fingerprint] interface.
2. On the displayed [Enroll Fingerprint] interface,
place your finger on the fingerprint sensor properly
according to the system prompt. For details, see 1.3
Finger Placement.
3. Place the same finger on the fingerprint sensor
for three consecutive times correctly. If the
enrollment succeeds, the system will display a
prompt message and automatically return to the
[Add User] interface. If the enrollment fails, the system will display a prompt
message and return to the [Enroll Fingerprint] interface. In this case, you
need to repeat the operations of step 2.
4. You can enroll the backup fingerprint by pressing [Fingerprint] again. A
user can enroll 10 fingerprints at maximum.
5. Press [Save] to save the current information and return to the previous
interface. Press [Exit] to return to the previous interface without saving the
current information.
23
MultiBio700 User Manual
24
3. Add User
3. 4 Enrolling a Password
1. Press [Password] on the [Add User] interface to
display the password management interface.
2. On the displayed keyboard interface, enter a
password and press [OK]. Re-enter the password
according to the system prompt and then press
[OK].

Tip:
The
device
supports
1-8
digit
passwords by default.
3. After the password is entered, an interface is
displayed as shown below. Press [Save] to save the
current information and return to the previous interface. Press [Exit] to return
to the previous interface without saving the current information.
25
MultiBio700 User Manual
3. 5 Enrolling a Face
1. Press [Face] on the [Add User] interface to
display the face enrollment interface.
2. On the displayed face enrollment interface, turn
your head to the left and right slightly, raise and
lower your head according to the voice prompts, so
as to enroll different parts of your face into the
system to assure the accurate verification. See 1.2
Enrollment Face Expressions.
3. If your face image is enrolled successfully, the
system will display a prompt message and
automatically return to the [Add User] interface.
4. Press [Save] to save the current information and return to the previous
interface. Press [Exit] to return to the previous interface without saving the
current information.
26
3. Add User
3.6 Entering a Group No.
During face enrollment, the device automatically
allocates a group No. starting from 1 for every user
in sequence. When the number of users in Group
No. 1 reaches the upper limit, the subsequent users
will under Group No. 2 automatically. Up to 100 face
images can be enrolled in Group No. 1 and only 50
face images can be enrolled in other groups. If you
use the group No. allocated by the device, you may
skip this section.
1. Press [Group No.] on the [Add User] interface to
display the group No. management interface.
2. On the displayed keyboard interface, enter your group No. and press [OK].
3. After the group No. is entered, an interface is displayed as shown below.
Press [Save] to save the current information and return to the previous
interface. Press [Exit] to return to the previous interface without saving the
current information.
 Tip: A valid group No. contains 1 to 24 digits. Please remember your
own group No.
27
MultiBio700 User Manual
28
3. Add User
3.7 Modifying User Rights
 Note: There are two types of rights respectively granted to two types of
users: the ordinary users and administrators. Ordinary users are only
granted the rights of face, fingerprint, or password verification, while
administrators are granted the access to the main menu for various
operations apart from having all the privileges granted to ordinary users.
1. On the [Add User] interface, press [Role: User] to change the user to an
administrator.
2. After the modification is done, the interface is as shown below. Press
[Save] to save the current information and return to the previous interface;
press [Exit] to return to the previous interface without saving the current
information.
29
MultiBio700 User Manual
3.8 Enroll Photos
If you had enrolled your photo in the system, the
system will display your enrolled photo in addition to
your ID and name after you pass the verification.
1. Press [Photo] on the [Add User] interface to
display the photo enrollment interface.
2. On the photo enrollment interface, stand naturally
in front of the screen. For details, see 1.1 Standing
Position, Posture and Face Expression. Press
[Capture] to capture the photo.
3. After taking the photo, press [Exit] to return to the
previous interface.
4. After the photo is taken, press [Save] to save the current information and
return to the previous interface; press [Exit] to return to the previous interface
without saving the current information.
30
3. Add User
3.9 User Access Settings
Press [User Access] on the [Add User] interface to display the user access
settings interface.
User Access settings are to set the user’s rights to verify and open the door,
such as the Verify Type, Time Zone and Duress FP management.
1. Verify Type:
(1) Group Verify Mode: If the user uses the group verify mode that he belong
to.
(2) Individual verify mode: Select the verification mode for this user instead
of the group verify mode. That will not affect other users in this group.
 Note:
(1) Only the products with the built-in ID card module support the ID card
verification.
(2) For the verify type, please refer to Appendix 4 Multi-combination
Authentication Mode. Only some types of devices support Multi-combination
31
MultiBio700 User Manual
authentication mode.
2. Time Zone:
(1) Group Time Zone: If the user uses the group time zone that he belong to.
(2) Individual time zone: Select the time zone of this user instead of the
group time zone. That will not affect other users in the group.
3. Duress FP:
Enroll a new duress fingerprint or cancel an existing
one. In any situation, only if the enrolled duress
fingerprint is verified, it will trigger the duress alarm.
Duress FP management:
(1) Register Duress FP:
Press [Reg. Duress FP] on the [User Access]
interface to display the [Enroll Fingerprint] interface.
On the displayed [Enroll Fingerprint] interface, place
your finger on the fingerprint sensor properly
according to the system prompt. For details, see 1.3
Finger Placement.
32
3. Add User
(2) Cancel duress FP:
Press [Can. Duress FP] on the [User Access] interface to popup the confirm
message. Select [YES] to delete the enrolled duress FP, otherwise select
[NO] to cancel the operation.
33
MultiBio700 User Manual
3.10 Enrolling an ID card ★
1. Press [Card] on the [Add User] interface to
display the [Enroll Card] interface.
2. The [Punch Card!] interface pops up as shown
below. Swipe your ID card properly in the swiping
area. For details, see 1.6 Appearance of the Device.
3. If the card passes the verification, the device will
display a prompt message “Read Successfully!
Card No.: **********”, and returns to the [Add User]
interface.
4. Press [Save] to save the current information and
return to the previous interface. Press [Exit] to return to the previous interface
without saving the current information.
34
4. User Management
4. User Management
Browse the user information, including the user ID,
name, fingerprint, face, ID card, password, rights,
group No. and user access settings through this
interface. To add, edit or delete the basic
information of users.
Press [User Management] on the main menu
interface to display the user management interface.
This user is an administrator.
 Note: The users are listed in alphabetical order by last name. If you
press a user name, you can access the editing interface of this user to edit or
delete the related user’s information.
35
MultiBio700 User Manual
4.1 Edit a User
Press a user name from the list to enter the [User Info] interface.
The User ID cannot be modified, and the other operations are similar to those
performed in add a user. You can re-enroll your fingerprint and face image,
change your password, modify the management rights and group number.
For example: Change the user rights from Administrator to ordinary user. As
shown below.
36
4. User Management
4.2 Delete a User
On the [User Info] interface, you can delete all or partial user information.
1. Press [Delete] to delete a user.
2. On the displayed interface, click [YES] to delete the current user or [NO] to
return to the previous interface.
3. On the [User Info] interface, press [Name], [Fingerprint], [Face] or
[Password] to delete the related user information and to re-enroll the new
information follow the device prompt.
37
MultiBio700 User Manual
4.3 Query a User
To facilitate administrators to locate a user quickly
from a large number of enrolled users, the device
enables to query by “User ID”.
User ID Query:
1. Press [Query] on the [User Management]
interface to display the User ID query interface.
2. Enter the user ID on the displayed interface, and
click [OK] to locate the cursor on the desired user.
38
5. Communication Settings
5. Communication Settings
You can set related parameters for the communication between the device
and PC, including the IP address, gateway, communication mode, subnet
mask, baud rate, device ID, and communication key.
39
MultiBio700 User Manual 1.0
5.1 Network Settings
When the device communicates with the PC over Ethernet, you need to
check the following settings:
IP Address: The IP address is 192.168.1.201 by default and can be changed
as required; the IP address of the device and that of the PC cannot be
duplicated.
Subnet Mask: The subnet mask is 255.255.255.0 by default and can be
changed as required.
Gateway: The gateway is 0.0.0.0 by default. If the device and the PC are not
located in the same network segment, you need to set the gateway.
When
the
device
communicates
with
the
PC
over
serial
ports
(RS232/RS485), you need to check the following settings:
RS232: This parameter is used to enable or disable the
communication. If the RS232 communication cables are used,
parameter to “ON”.
RS485: This parameter is used to enable or disable the
communication. If the RS485 communication cables are used,
parameter to “ON”.
Baud Rate: This parameter is used to set the baud rate
RS232
set this
RS485
set this
for the
communication between the device and the PC. It includes five options: 9600,
19200, 38400, 57600, and 115200. The higher baud rate is recommended for
the RS232 communication to achieve high speed communication, while the
lower baud rate is recommended for the RS485 communication to achieve
stable low-speed communication.
Device ID: This parameter is used to set the ID of device from 1 to 254. If the
RS232/RS485 communication is adopted, you need to enter the device ID on
the software communication interface.
Comm. Key: To enhance the security of attendance data, you can set a
password for the connection between the device and PC. Once the password
is set, you can connect the PC with the device to access the attendance data
40
5. Communication Settings
only after entering the correct password. The default password is 0 (that is,
no password). Once a password is set, you need to enter this password
before connecting the PC software with the device; otherwise, the connection
is unsuccessful. 1 to 6 digits passwords are supported.
Considering the massive data including the fingerprint and face templates
stored in the device, it is recommended to transfer the data between the device
and PC over network to enhance the transfer speed.
41
MultiBio700 User Manual 1.0
5.2 Wiegand Output
Wiegand Format: The system has two built-in
formats Wiegand 26-bits and Wiegand 34-bits,
and also supports the format customization function
to meet individualized requirements.
Failed ID: Refers to the value output by the system
upon verification failure. The output format is
subject to the setting of “Wiegand Format”. The
default value scope of Failed ID is 0–65535.
Site Code: The site code is used for a customized
Wiegand format. The site code is similar to the
device ID, but the site code is customizable and can be duplicated among
different devices. The default value scope of the Site Code is 0–255.
Pulse Width: Refers to the width of the Wiegand pulse in microseconds. The
default value scope of the pulse width is 1–1000.
Pulse Interval: Refers to the interval of the Wiegand pulse in microseconds.
The default value scope of the pulse width is 1–10000.
Output: Refers to the contents output upon successful verification. You can
select the “User ID” or “Card Number” as the output.
42
5. Communication Settings
5.2.1 Wiegand 26-bits Output Description
The system has a built-in Wiegand 26-bits format. Press [Wiegand Format],
and select “Standard Wiegand 26-bits”.
The composition of the Wiegand 26-bits format contains 2 parity bits and 24
bits for output contents (“User ID” or “Card Number”). The binary code of
24-bits represent up to 16,777,216 (0–16,777,215) different values.
1
2
Even parity
25 26
User ID/Card Number
Odd parity bit
Definition of Fields:
Field
Meaning
Even parity bit
Judged from bit 2 to bit 13. The even parity bit is 1 if
the character has an even number of 1 bit; otherwise,
the even parity bit is 0.
User
ID/
Card
Number (bit 2-bit
User ID/Card Number (Card Code, 0–16777215)
Bit 2 is the Most Significant Bit (MSB).
25)
Odd parity bit
Judged from bit 14 to bit 25. The odd parity bit is 1 if
the character has an even number of 1 bit; otherwise,
the odd parity bit is 0.
For example, for a user with the user ID of 12345, the enrolled card number
is 0013378512 and the failed ID is set to 1.
1. When the output is set to “User ID”, the Wiegand output is as follows upon
successful verification:
00000000000110000001110011
Even parity bit User ID = Binary code of 12345 Odd parity bit
43
MultiBio700 User Manual 1.0
2. When the output is set to “Card Number”, the Wiegand output is as follows
upon successful verification:
11100110000100011110100000
Even parity bit User ID = Binary code of 0013378512 Odd parity bit
3. The Wiegand output is as follows upon verification failure:
00000000000000000000000010
Even parity bit Failed ID = Binary code of 1
Odd parity bit
 Note: If the output contents exceed the scope allowed for the Wiegand
format, the last several bits will be adopted and first several bits are
automatically discarded. For example, the user ID 888 888 888 is 110 100
111 110 110 101 111 000 111 000 in binary format. Wiegand26 only supports
24 bits, that is, it only outputs the last 24 bits, and first 6 bits “110 100” are
automatically discarded.
44
5. Communication Settings
5.2.2 Wiegand 34-bits Output Description
The system has a built-in Wiegand 34-bits format. Press [Wiegand Format],
and select “Standard Wiegand 34-bits”.
The composition of the Wiegand 34-bits format contains 2 parity bits and 32
bits for output contents (“User ID” or “Card Number”). The binary code of
32-bits represent up to 4,294,967,296 (0–4,294,967,295) different values.
1
2
EvenParityBit
33 34
User ID/Card Number
Odd parity bit
Table 2 Definition of Fields
Field
Meaning
Even parity bit
Judged from bit 2 to bit 17. The even parity bit is 1 if
the character has an even number of 1 bit; otherwise,
the even parity bit is 0.
User
ID/Card
Number (bit 2-bit
User ID/Card Number (Card Code, 0–4,294,967,295)
Bit 2 is the Most Significant Bit (MSB).
33)
Odd parity bit
Judged from bit 18 to bit 33. The odd parity bit is 1 if
the character has an even number of 1 bit; otherwise,
the odd parity bit is 0.
For example, for a user with the user ID of 123456789, the enrolled card
number is 0013378512 and the failed ID is set to 1.
1. When the output is set to “User ID”, the Wiegand output is as follows upon
successful verification:
0000001110101101111001101000101011
Even parity bit User ID = Binary code of 123456789
Odd parity bit
45
MultiBio700 User Manual 1.0
2. When the output is set to “Card Number”, the Wiegand output is as follows
upon successful verification:
0000000001100110000100011110100001
Even parity bit User ID = Binary code of 0013378512
Odd parity bit
3. The Wiegand output is as follows upon verification failure:
0000000000000000000000000000000010
Even parity bit
Failed ID = Binary code of 1
Odd parity bit
46
5. Communication Settings
5.2.3 Customized Format
Apart from the two built-in formats Wiegand 26-bits and Wiegand 34-bits,
the system also supports the format customization function to meet
individualized requirements.
The customized format consists of two character strings: the data bits and
parity bits. These two character strings need to be defined separately. Data
bits define the number of binary bits output by Wiegand as well as the
meaning of each bit. The data bits output by Wiegand can be a card number
(C), site code (s), facility code (f), manufacturer code (m) and parity bits (p).
Parity bits define the check mode of each bit in data bits and ensure the
correctness of data bits during transfer through the parity check. The parity
bits can be set to odd check (o), even check (e) and both odd check and even
check (b). There is a one-to-one correspondence relationship between the
data bits and parity bits.
For example, the Wiegand26 can be customized as follows:
Definition of data bits: pssssssssccccccccccccccccp
Definition of parity bits: eeeeeeeeeeeeeooooooooooooo
 Note: Wiegand26 consists of 26 bits. The first
th
bit is the even parity bit of bits 2 to 13; the 26 bit is
the odd parity bit of bits 14 to 25; the second to the
ninth bits are the site code; the 10th to the 25th bits
are the card number.
For details about the Wiegand protocol, see
Appendix 3 Introduction of Wiegand.
To customize Wiegand format, proceed as follows:
(1) Select [Define Format] and the [Set] key is then
enabled.
47
MultiBio700 User Manual 1.0
(2) Press [Set] to display the [User Define Format] interface, as shown in the
following figure:
(3) Click the entry box below “Card Format” to display the following interface:
Display Input
Display the Numb
Cancel Input
Backspace
Confirm Input
Clear Input
Characters used to define data bits and their meanings:
c: Indicates the card number, that is, the output
contents, it can be set to User ID/Card Number
through menu operations.
f: Indicates the facility code which is 0 by default. It
is not configurable. To modify it, please contact the
equipment supplier.
m: Indicates the manufacturer code which is 0 by
default. It is not configurable. To modify it, please
contact the equipment supplier.
p: Indicates the parity position.
s: Indicates the site code which can be set from 0 to
255 by default.
48
5. Communication Settings
(4) Click the entry box below “Parity Format” to display the following interface:
Characters used to define parity bits and their meanings:
o: Indicates the odd check, that is, there is an odd number of 1’s in the bit
sequence (including one parity bit). For example, for 1000110(0), the parity
bit is 0 and there are already three 1’s. After 0 is suffixed to 1000110, there is
still an odd number of 1’s.
e: Indicates the even check, that is, there is an even number of 1’s in the bit
sequence (including one parity bit). For example, for 1000110(1), the parity
bit is 1 and there are already three 1’s. After 1 is suffixed to 1000110, there is
an even number of 1’s.
b: Indicates both odd check and even check.
For example, Definitions of several universal Wiegand formats.
Wiegand34
Data bits:
pccccccccccccccccccccccccccccccccp
Parity bits:
eeeeeeeeeeeeeeeeeooooooooooooooooo
Note: Wiegand34 consists of 34 bits. The first bit is the even parity bit of bits 2
to 17; the 34th bit is the odd parity bit of bits 18 to 33; the second to the ninth
bits are the site code; the 10th to the 25th bits are the card number.
Wiegand37a
Data bits: pmmmmsssssssssssscccccccccccccccccccp
Parity bits: oeobeobeobeobeobeobeobeobeobeobeobeoe
Note: Wiegand37a consists of 37 bits. The first bit is the odd parity bit of bits 3,
4, 6, 7, 9, 10, 12, 13, 15, 16, 18, 19, 21, 22, 24, 25, 27, 28, 30, 31, 33, 34 and
36; the 37th bit is the odd parity bit of bits 2, 4, 5, 7, 8, 10, 11, 13, 14, 16, 17,
19, 20, 22, 23, 25, 26, 28, 29, 31, 32, 34 and 35; bits 4, 7, 10, 13, 16, 19, 22,
49
MultiBio700 User Manual 1.0
25, 28, 31 and 34 participate in both odd and even parity check. Bits 2 to 5
are manufacturer code; bits 6 to 17 are the site code; bits 18 to 36 are the
card number.
Wiegand37
Data bits:
pmmmffffffffffssssssccccccccccccccccp
Parity bits:
eeeeeeeeeeeeeeeeeeooooooooooooooooooo
Note: Wiegand37 consists of 37 bits. The first bit is the even parity bit of bits 2
to 18; the 34th bit is the odd parity bit of bits 19 to 36; the second to the fourth
bits are the manufacturer code; the 5th to the 14th bits are facilitate code; the
15th to the 20th bits are the site code; the 21st to the 36th bits are the card
number.
Wiegand50
Data bits: pssssssssssssssssccccccccccccccccccccccccccccccccp
Parity bits:
eeeeeeeeeeeeeeeeeeeeeeeeeooooooooooooooooooooooooo
Note: Wiegand50 consists of 50 bits. The first bit is the even parity bit of bits 2
to 25; the 50th bit is the odd parity bit of bits 26 to 49; the second to the 16th
bits are the site code; the 17th to the 49th bits are the card number.
50
5. Communication Settings
5.3 Wiegand Input
Wiegand Format: The system has two built-in
formats Wiegand 26-bits and Wiegand 34-bits,
and also supports the format customization function
to meet individualized requirements. About the
Wiegand format, please refer to 5.2 Wiegand
Output.
Bit counts: Wiegand data digit length.
Pulse width: Pulse width is 100 microseconds by
default, which can be adjusted from 20 to 800.
Pulse interval: It is 900 microseconds by default,
which can adjusted between 200 and 20000.
Input: Content contained in Wiegand input signal, including User ID or card
number.
51
MultiBio700 User Manual 1.0
6. System Configuration
Through the [System] menu, you can set system-related parameters,
including the General, Display, Fingerprint, Face, Log settings, Shortcut Def,
Access Control Set, and Firmware Update, to enable the device to meet user
requirements to the greatest extent in terms of functionality and display.
52
6. System Configuration
6.1 General Parameters
Keyboard Clicks: This parameter is used to set
whether to generate beep sound in response to
every keyboard touch. Select “ON” to enable the
beep sound, and select “OFF” to mute.
Voice Prompts: This parameter is used to set
whether to play voice prompts during the operation
of the device. Select “ON” to enable the voice
prompt, and select “OFF” to mute.
Volume (%): This parameter is used to adjust the
volume of voice prompts.
Lock Power Key: This parameter is used to set
whether to lock the power key. Select “ON” to disable the power key. If you
select “OFF”, and press the power key, the device will be shut down in three
seconds.
53
MultiBio700 User Manual 1.0
6.2 Interface Parameters
Language: This parameter is used to display the
current
language
multilingual-capable
between
different
used
by
the
device.
devices,
you
can
languages
through
For
switch
this
parameter.
Toolbar: This parameter is used to display the style
of the shortcut keys on the initial interface. It can be
set to “Auto Hide” and “Permanent Display”. By
selecting “Auto Hide”, you can manually display or
hide the toolbar. By selecting “Permanent Display”,
you can permanently display the toolbar on the
initial interface.
Sleep Time (S): This parameter is used to specify a period after which the
device is put in sleep mode if no operation within this period. You can wake
up the device from sleep by pressing any key or touching the screen.
54
6. System Configuration
6.3 Fingerprint Parameters
1: 1 Threshold: This parameter is used to set the
threshold
of
matching
between
the
current
fingerprint and the fingerprint template enrolled in
the device in the 1:1 verification mode. If the
similarity between the current fingerprint and the
fingerprint template enrolled in the device is larger
than this threshold, the matching is successful;
otherwise, the matching is not successful.
1: N Threshold: This parameter is used to set the
threshold
of
matching
between
the
current
fingerprint and the fingerprint template enrolled in
the device in the 1: N verification mode. If the similarity between the current
fingerprint and the fingerprint template enrolled in the device is larger than
this threshold, the matching is successful; otherwise, the matching is not
successful.
The recommended thresholds are as follows:
(FRR)
High
Medium
Low
(FAR)
Low
Threshold
1: N
1: 1
45
25
Medium
35
15
High
25
10
Algorithm Version: This parameter is used to select the fingerprint algorithm
version between 9.0 and 10.0. Please select the algorithm version with
caution because the fingerprint templates of these two algorithm versions are
incompatible.
Fingerprint Image: This parameter is used to set whether to display the
55
MultiBio700 User Manual 1.0
fingerprint image on the screen during fingerprint enrollment or comparison. It
has four options:
Show for Enroll: Display the fingerprint on the screen in enrolling process.
Show for Match: Display the fingerprint on the screen in verification process.
Always Show: Display the fingerprint on the screen in enrolling and verifying
process.
Never Show: Never display the fingerprint on the screen in any case.
56
6. System Configuration
6.4 Face Parameters
1: 1 Threshold: This parameter is used to set the
threshold of matching between the current face and
the face template enrolled in the device in the 1:1
verification mode. If the similarity between the
current face and the face template enrolled in the
device is larger than this threshold, the matching is
successful;
otherwise,
the
matching
is
not
successful. The valid value scope is 55─120. The
higher the threshold, the lower the FAR and the
higher the FRR are, and vice versa.
1:1: N Threshold: This parameter is used to set the
threshold of matching between the current face and the face template
enrolled in the device in the 1: N verification mode. If the similarity between
the current face and the face template enrolled in the device is larger than
this threshold, the matching is successful; otherwise, the matching is not
successful. The valid value scope is 65─120. The higher the threshold, the
lower the FAR and the higher the FRR are, and vice versa.
The recommended thresholds are as follows:
FRR
FAR
High
Low
Threshold
1: N
1:1
90
80
Medium
Medium
80
70
Low
High
75
65
Exposure: This parameter is used to set the exposure value of the camera.
Gain: This parameter is used to set the gain value of the camera.
Quality: This parameter is used to set a quality threshold for the face images
57
MultiBio700 User Manual 1.0
obtained. The device accepts the face images and processes them by
adopting the face algorithm when their quality is higher than the threshold;
otherwise, it filters these face images.

Note: Improper adjustment of the Exposure, Gain and Quality
parameters may severely affect the performance of the device. Please adjust
the Exposure parameter only under the guidance of the after-sales service
personnel from our company.
58
6. System Configuration
6.5 Log Settings
Log Alert: When the available space is insufficient
to store the specified number of attendance records,
the device will automatically generate an alarm
(Value scope: 1-99).
Dup. Punch Period (m): If a user’s attendance
record already exists and the user punches in again
within the specified period (unit: minute), the second
attendance record will not be stored (Value scope:
1-60 minutes).
59
MultiBio700 User Manual 1.0
6.6 Keyboard Definitions
Define touch screen functional shortcut keys.
1. Press [Shortcut Def] to display the [Edit] interface, as shown below.
2. If you want to cancel the shortcut key, press [Status] to enter the edit
interface, select the value to “Undefined”.
3. Edit the item [Code], select [Label] (Six attendance state option). Select the
state of [Auto Switch], the interface as shown above.
4. Press [Save] to save the modification and exit.
60
6. System Configuration
6.7 Access Settings
Access control settings are to set user’s open door
time zone, control lock and set related device
parameters.
To unlock, the enrolled user must accord with the
following conditions:
1. The current unlock time should be in the effective
time of the user time zone or group zone.
2. The group where the user is must be in access
control (or in the same access control with other
group, to open the door together).
The new enrolled user is under the first group by default, and use the No. 1
group time zone, the No. 1 access control group. The new enrolled user is in
unlocking state (if you have modified the related settings of access control,
the system will be changed with the modification).
61
MultiBio700 User Manual 1.0
6.7.1 Time zone setting
Time zone is the minimum unit of access control
option. The whole system can define 50 time zones.
Every time zone consists of seven time sections
(that is, one week). Every time section is the
effective time zone within 24 hours every day. Every
user can set 3 time zones. It’s “or” between the
three zones. It is effective if only one is satisfied.
Every time section format is HH:MM-HH:MM,
namely, accurate to minute.
If end time is smaller than start time (23:57- 23:56),
the whole day is forbidden. If end time is bigger than
start time (00:00- 23:59), it is effective section.
Effective time zone for user unlocking: 00:00-23:59 or end time is bigger than
start time.

Notice: System default time zone 1 as whole day open (namely, the
new enrolled user is unlocking).
62
6. System Configuration
6.7.2 Holiday setting
Special access control time may be needed during
holidays. It is different to modify everybody’s access
control time. So a holiday access control time can
be set, which is applicable for all employees.
1. Add holiday:
(1) Enter holiday add interface, press the key to edit
the items.
(2) Press the touch screen number key to set the
value, after setting, press [OK] to save, and press [X]
for exit and return to the previous interface.
(3) Press [Save] to save the current information and
return to the previous interface; press [Exit] directly to return to the previous
interface without saving the current information.
63
MultiBio700 User Manual 1.0
2. Edit holiday
Select the holiday to be edited and enter the edit
interface. The edit operation is similar to add holiday.
After editing, press [Save] to save and return to the
previous interface.
 Notice: If holiday access control time is set,
user’s open door time zone during holiday is subject
to the time zone here.
3. Delete holiday
Select the holiday to be deleted. Press [Delete] to
popup the confirm interface as follows. Select [Yes]
to delete this holiday, otherwise select [No] to
cancel the operation.
64
6. System Configuration
6.7.3 Group time zone setting
Grouping is to manage employees in groups.
Employees in group use group time zone by default.
Group members can also set user time zone. Every
group can hold three time zones. The new enrolled
user belongs to Group 1 by default and can also be
allocated to other groups.
1. Add group time zone
(1) Enter the Add Group interface; press the key to
edit the items.
Code: Enter the number edit interface to set the
value.
VerType: Select the Group Verify Type.
Holiday No.: Select if the Time zone is valid in
holiday.
Time Zone: Select the Group Time Zone.
(2) After editing, press [Save] to save the current
information and return to the previous interface;
press [Exit] directly to return to the previous interface without saving the
current information.
 Note:
(1) RF means ID card verification. Only the products with the built-in ID card
65
MultiBio700 User Manual 1.0
module support the ID card verification.
(2) For Multi-combination verification, please refer to Appendix 4
Multi-combination Authentication Mode.
 Notice:
1. If the holiday is valid, only when there is an intersection between group
zone and holiday time zone, can the group member open the door.
2. If the holiday is invalid, the access control time of group member won’t be
affected by holiday.
2. Edit group time zone
Press the line to be edited, and enter the edit
interface. After editing, press [Save] to save the
current information and return to the previous
interface; press [Exit] directly to return to the
previous interface without saving the current
information.
66
6. System Configuration
3. Delete group time zone
Select the line to be deleted. Press [Delete] to
popup the confirm interface as follows. Select [Yes]
to delete this holiday, otherwise select [No] to
cancel the operation.
67
MultiBio700 User Manual 1.0
6.7.4 Unlock Combination Setting
Make
various
groups
into
different
access
controls
to
achieve
multi-verification and improve security. An access control can be made up of
5 groups at most.
1. Add Unlock Combination
(1) Enter holiday add Combination Setting interface,
press the key to edit the items.
(2) Press the touch screen number key to set the
value, after setting, press [OK] to save, and press [X]
for exit and return to the previous interface.
(3) Press [Save] to save the current information and
return to the previous interface; press [Exit] directly
to return to the previous interface without saving the
current information.
68
6. System Configuration
2. Edit Unlock Combination
Select the line to be edited. Press the item directly
to enter the edit interface. After editing, press [Save]
to save the current information and return to the
previous interface; press [Exit] directly to return to
the previous interface without saving the current
information.
3. Delete Unlock Combination
Select the line to be deleted. Press [Delete] to
popup the confirm interface as follows. Select [Yes]
to delete this holiday, otherwise select [No] to
cancel the operation
69
MultiBio700 User Manual 1.0
6.7.5 Access control parameter
Through the [Access] menu, you can set the
parameters of the electronic locks and related
access control devices.
Lock Delay: Indicates the duration for the device to
place the electric lock in open state. (Value scope:
1-10 seconds)
Door Sensor Delay: Indicates the delay for
checking the door sensor after the door is opened. If
door sensor state is inconsistent with the normal
state set by the door sensor switch, an alarm will be
triggered, and this period of time is regarded as the
“door sensor delay”. (Value scope: 1-99 seconds)
Door Sensor Mode: Includes the None, Normally Open (NO), and Normally
Closed (NC) modes. “None” indicates that the door sensor switch is not used.
“NO” indicates that the door sensor is open in the normal state. “NC”
indicates that the door sensor is closed in the normal state.
Alarm Delay: Indicates the duration from the detection of the door sensor
exception to the generation of alarm signal. (Value scope: 1-99 seconds)
Failure Alarm Threshold: When the failed press times reach the set times,
alarm signal will come out (effective value: 1-9 times).
NC Time Zone: Set time zone for access control NC. Nobody can unlock
during this time zone.
NO Time Zone: Set time zone for access control NO. The lock is always in
valid state during this time zone.
Valid in Holiday: Define time zone for NO or NC. Whether the time zone set
in holiday time zone is valid.
70
6. System Configuration
 Notice:
1. If the Time Zone of normally open or normally closed has been set, please
switch door sensor to no, otherwise it will produce alarm signal during Normal
close Time Zone or Normal open Time Zone.
2. If the normally open or normally closed Time Zone is not defined yet by the
time, the equipment will prompt that you to define the Time Zone, and
transfer you to the Time Zone interface to add.
71
MultiBio700 User Manual 1.0
6.7.6 Duress Alarm Parameters
There are duress alarm parameters setting in the
device. When an employee comes across a duress
situation, he can use the set duress alarm mode to
verify. The device will open the door as usual, but
the alarm signal will be sent to the alarm.
1: 1 Trigger: if select “Yes”, when user use 1: 1
match mode, alarm signal will come out. Or there is
no alarm signal.
1: N Trigger: if select “Yes”, when user use 1: N
match mode, alarm signal will come out. Or there is
no alarm signal.
Password Trigger: If select “Yes”, when a user use password verification
mode, alarm signal will come out. Or there is no alarm signal.
Alarm Delay: After duress alarm gets started, the alarm signal will not output
directly. It can be defined. After the set time period, the alarm signal will be
generated automatically (0-255 seconds).
72
6. System Configuration
6.7.7 Anti-Pass back setting
Set the device Anti-Pass back function.
APB Direction: There are four options: None,
APB-Out, APB-In, APB-Out/In.
Device Status: There are three options: Exit
Control, Entry Control and None.
For Anti-Pass back function, please refer to
Appendix 5 Anti-Pass back.
Anti-Pass back setting operation:
(1) Enter Anti-Pass back setting interface, press the
key to edit the items.
(2) Press the touch screen number key to set the
value, after setting, press [OK] to save, and press [X] for exit and return to the
previous interface.
(3) Press [Save] to save the current information and return to the previous
interface; press [Exit] directly to return to the previous interface without
saving the current information.
73
MultiBio700 User Manual 1.0
6.8 Update
You can upgrade the device firmware by using the
upgrade file in the USB disk through this function.
If you need the firmware upgrade file, please contact our technical
support personnel. Generally the firmware upgrade is not recommended.
74
7. Data Management
7. Data Management
Through the [Data Mgt.]
menu, you can perform
management
of
data
stored on the device, for
example,
delete
attendance
delete
all
the
records,
data,
clear
administrator, restore the
device to factory settings,
and query user records.
1. Delete Transactions: Delete all the attendance records.
2. Delete All Data: Delete all the information of enrolled personnel, including
their fingerprints, face images and attendance records.
3. Clear Administrator: Change all administrators to ordinary users.
4. Restore to Factory Settings: Restore all parameters on the device to
factory settings.
 Notice: The employee information and attendance records will not be
deleted during restoration to factory settings.
5. Query Record: After check-in successfully, the employee’s attendance
records are saved in the device. You can easily query these attendance
records.
User ID: Enter the user ID of the employee to query. If this field is left blank,
you can query the attendance records of all the employees. If you enter a
user ID, you can query the attendance records of this employee.
75
MultiBio700 User Manual 1.0
Query Time Period: Select a time period to query, including the customized
time period, yesterday, this week, last week, this month, last month, and all
time periods.
Start and End: When you select a customized time period, you need to input
a start time and an end time. When you select other options for the time
period, the start and end time will be automatically adjusted to the related
time.
After setting the query conditions, press [Query] and the records that meet
the specified query conditions will be displayed on screen.
Select the row where the desired record is located, you can query the
detailed information of this record.
For example, press User ID and enter the edit interface, input the ID number
and press [Query], the query result will display as below.
76
7. Data Management
77
8. Date/Time Setting
8. Date/Time Setting
8.1 Set Date/Time
The date and time of the device must be set
accurately to ensure the accuracy of attendance
time.
1. Press [Menu] on the initial interface to display the
main menu interface.
2. Press [Time/Date] on the main menu interface to
display the time setting interface.
3. Select the desired date and time by pressing the
parameter. For the time format, there are 10 formats
to select from. Both 12-hour and 24-hour time
systems are supported.
4. Press [Save] to save the current information and return to the previous
interface. Press [Exit] to return to the previous interface without saving the
current information.
78
8. Date/Time Setting
8.2 Bell Setting ★
Lots of companies need to ring their bells to signal the start and end of work
shifts, and they usually manually ring their bells or use electric bells. To lower
costs and facilitate management, we integrated the time bell function into the
device. You can set the alarm time and duration for ringing the bell based on
your requirements, so that the device will automatically play the selected ring
tone and triggers the relay at the alarm time, and stop playing the ring tone
after the set duration.
Press [Bell] on the [Date/Time] menu to display the bell setting interface, as
shown in figure below.
1. Add a bell
1) The displayed bell setting interface lists all the bells. Click [Add] to display
the [Add] interface.
2) On the [Add] interface, set the following parameters:
Bell Time: This parameter is used to set a time point when the device
automatically plays a bell ring tone every day.
Bell Date: This parameter is used to set which day the device automatically
79
MultiBio700 User Manual 1.0
plays a bell ring tone.
Ring Tone: This parameter is used to set the bell ring tone.
Volume: This parameter is used to set the volume of ring tone.
Repeat: This parameter is used to set the alarm times.
State: This parameter is used to set whether to enable the bell.
Bell Type: You can select between internal ringing and external ringing. For
internal ringing, the ring tone is played by the loudspeaker of the device. For
external ringing, the ring tone is played by an external electric bell that is
connected with the device.
2. Edit and delete a bell
Press a bell in the list on the bell setting interface to
display the [Edit] interface, with the similar
operation as “Add a bell”.
 Notice: Only some models have this function. If you need it, please
contact our business representative or technician.
80
9. Auto Test
9. Auto Test
The auto test enables the system to automatically test whether functions of
various modules are normal, including the screen, sensor, voice, face,
keyboard and clock tests.
1. Test Screen: The device automatically tests the display effect of the color
TFT display by displaying full color, pure white and pure black and checks
whether the screen displays properly. You can continue the test by touching
the screen or exit it by pressing [Exit].
2. Test Fingerprint: The device automatically tests whether the fingerprint
sensor works properly by checking whether the fingerprint images are clear
and acceptable. When the user places his/her finger on the sensor, the
collected fingerprint image is displayed on the screen in real-time. Press [Exit]
to exit the test.
3. Test Voice: The device automatically tests whether the voice files are
complete and the voice quality is good by playing the voice files stored in the
device. You can continue the test by touching the screen or exit it by pressing
81
9 自动测试
[Exit].
4. Test Face: The device automatically tests whether the camera works
properly by checking whether the collected face images are clear and
acceptable. Press [Exit] to exit the test.
5. Test Keyboard: The device tests whether every key on the keyboard
works normally. Press any key on the [Keyboard Test] interface to check
whether the pressed key matches the key displayed on screen. The keys are
dark-gray before pressed, and turn blue after pressed. Press [Exit] to exit the
test.
6. Test Time: The device tests whether its clock works properly by checking
the stopwatch of the clock. Touch the screen to start counting, and touch it
again to stop to check whether the counting is accurate. Press [Exit] to exit
the test.
7. Screen Calibration:
You can perform all the menu operations by touching the screen with one of
your fingers or a touch pen. When the touch screen is less sensitive to the
touch, you can perform a screen calibration through menu operations.
The Screen Calibration Operation:
(1) Press [Menu] on the initial interface to display
the main menu interface.
(2) Press [Calibration] on the [Auto Test] interface to
display the screen calibration interface.
(3) Touch the center of the cross “+”.
(4) Repeat Step 3 following the move of the “+” icon
to different locations on the screen.
(5) Touch the center of the cross at five locations on
the
screen
correctly.
When
the
message
“Calibrating screen, pls wait……” is displayed on
82
9. Auto Test
screen, the calibration succeeds and the system automatically returns to the
main menu. If the calibration fails, the system recalibration will start from Step
3.
83
10. USB Disk Management
10. USB Disk Management
Through the [Dn/Upload] menu, you can download user information and
attendance data stored in a USB disk to related software or other fingerprint
recognition equipment.
1. Download Transactions: Download all the attendance data from the
device to a USB disk.
2. Download User: Download all the user information, fingerprints and face
images from the device to a USB disk.
3. Download user photos: Download the employees’ photos from the device
to a USB disk.
4. Upload User: Upload the user information, fingerprints and face images
stored in a USB disk to the device.
5. Upload User Photo: Upload the JPG documents that are named after the
user IDs and stored in a USB disk to the device, so that user photos can be
displayed after the employee passes the verification. See Appendix 3 Photo
ID Function.
84
11. System Information
11. System Information
You can check the storage status as well as version
information of the device through the [System
Information] option.
Records:
The
number
of
enrolled
users,
administrators and passwords are displayed on the
[Records] interface; the total fingerprint storage
capacity and occupied capacity as well as the total
attendance storage capacity and occupied capacity
are graphically displayed respectively.
Device: The device name, serial number, version
information, vendor and date of manufacture are displayed on the [Device]
interface.
85
12. Appendix
12. Appendix
Appendix 1 T9 Input Instructions
The
input
device
supports
English
numbers
and
to
characters,
symbols.
Press related button to input
text. For example, press
[Name] to display the text
input interface, as shown in
the figure:
①Keyboard Area
②Text Display Area
③Text List Area
④Exit
⑤Delete
⑥Enter
⑦Space
⑨Character/English
⑩Upper/Lower Case
86
12. Appendix
To enter a name, proceed as follows:
1. Press [Name] on the [Add] interface, as shown in figure below.
2. Enter the letter characters, and a list of characters in relation to the letter is
presented in the text display area.
3. If the desired character is displayed in the text display area, press this
character. And this character is at the same time displayed on the [Name]
button. Enter next character by repeating Step 2.
4. After finishing the entry of name, press [X] to exit the keyboard interface
and return to the previous interface.
87
MultiBio700 User Manual
Appendix 2 Introduction of Wiegand
Wiegand26 is an access control standard protocol established by the Access
Control Standard Subcommittee affiliated to the Security Industry Association
(SIA). It is a non-contact IC card reader interface and output protocol.
Wiegand26 defines the interface between the card reader and controller used
in the access control, security and other related industrial fields. Wiegand26
helps standardize the work of the card reader designers and controller
manufacturers. The access control products manufactured by our company
are also designed by following this protocol.
Digital Signals
The figure below is a sequence diagram in which the card reader sends
digital signals in bit format to the access controller. In this sequence diagram,
Wiegand follows the SIA’s access control standard protocol for the 26-bit
Wiegand card reader (one pulse time ranges between 20 us and 100 us, and
the pulse jump time ranges between 200us and 20ms). Data1 and Data0 are
high level (larger than Vol) signals till the card reader prepares to send a data
stream. The asynchronous low-level pulse (smaller than Vol) generated by
the card reader is sent to the access control panel (The saw-tooth wave as
shown in Figure below) through Data1 or Data0. Data1 and Data0 pulses will
neither overlap nor be generated synchronously. The table below lists the
maximum and minimum pulse width (a consecutive pulse) and pulse jump
time (time between pulses) allowed by the F series fingerprint access control
device.
88
12. Appendix
Figure: Sequence Diagram
Table: Pulse Time
Symbol
Definition
Typical Value of Reader
Tpw
Pulse Width
100 µs
Tpi
Pulse Interval
1 ms
89
MultiBio700 User Manual
Appendix 3 Photo ID Function
The Photo ID function is used to display the photo
enrolled by a user or stored in a USB disk on the
screen in addition to such information as the user ID
and name.
[Operation Steps]
1. When the photo taken by the device is used, the
photo can be displayed upon successful verification.
2. To use a photo stored in a USB disk, proceed as
follows:
1) Create a folder with the name of “photo” in the
USB disk, and store users' photos under this folder.
2) The user photos must be in JPG format and named after their IDs. For
example, for the user with the user ID of 154, the photo name must be
154.jpg.
3) Insert the USB disk into USB slot on the device, and select USB Disk
Management -> Upload -> Upload Photos. Then user photos can be
displayed upon successful verification.
 Note:
1) The length of a user name cannot exceed 24 digits.
2) The recommended size of a user photo is less than 30 kbit.
3) The uploaded new user photo will overwrite the existing photo in related to
the user ID.
4) To download user photos, select USB Disk Management -> Download ->
Download User Photos. A folder with the name of “photo” will be
automatically created on the USB disk, and all downloaded user photos are
90
12. Appendix
stored under this folder.
91
MultiBio700 User Manual
Appendix 4 Multi-combination Authentication Mode ★
Besides this function only is owned by the fingerprint access control machine
that has been appointed, most of the fingerprint machines only have two
ways to verify by fingerprint and password, we provide a personal or group
Multi-combination Authentication Mode for high security Access control area,
verification type main include five elements that are User Number (PIN),
Fingerprint (FP), Face (FACE), Password (PW) and RF card (RF), which can
combine into multi-combination.

Note: The RF card is used for ID card verification, the function of ID
card verification only is validity in the machine which ID card function is
provided with.
These symbols illustrate what follow the table different means.
● “/” is or
●”+” follow next operation
● “&” is and
● FACE (Face)
● FP (fingerprint)
● PWD (Password)
● RF (RF card)
● PIN (user ID)
If Fingerprint, Face, Password and Card have been enrolled for the user, the
verification procedure is follow.
Type
FACE&PIN/FP/PW/RF
What you do
FACE+PIN or RF or PW or RF are verified
1) PIN++FACE(1:1)
2) FP(1:N)
3) PIN+PW+“OK”
4) RF(1:N)
92
12. Appendix
FP&PW
FP + PW are verified
1) FP(1:N)+PW+“OK”
2) PIN+FP(1:1)+PW+“OK”
3) PIN+PW+“OK”+FP
FP&RF
FP + RF are verified
1) RF+FP(1:1)
2) FP(1:N)+RF
3) PIN+FP(1:1)+RF
FACE&FP
FACE + FP are verified
1) FP(1:N)+FACE
2) FACE(1:N)+FP
3) PIN+FACE(1:1)+FP
4) PIN+FP(1:1)+FACE
FACE&PW
FACE + PW are verified
1) FACE(1:N)+PW+“OK”
2) PIN+FACE(1:1)+PW
3) PIN+PW+FACE
FACE&RF
FACE + RF are verified
1) FACE(1:N)+RF
2) PIN+FACE(1:1)+RF
3) RF(1:N)+FACE
FP
Only FP is verified.
1) PIN+FP(1:1)
2) FP(1:N)
PW
Only PW is verified
PIN+PW+“OK”
RF
Only RF is verified
RF(1:N)
93
MultiBio700 User Manual
FACE&PIN
FACE + PIN are verified
PIN+FACE(1:1)
FP/RF
FP or RF is verified
1) PIN+FP(1:1)
2) RF(1:N)
3) FP(1:N)
PW/RF
FP or RF is verified
1) PIN+PW+“OK”
2) RF(1:N)
FP/PW
FP or PW is verified
1) PIN+FP(1:1)
2) FP(1:N)
3) PIN+PW+“OK”
PIN&FP
PIN + FP are verified
PIN+FP(1:1)
FP&PW&RF
FP + PW + RF are verified
1) FP(1:N)+PW+“OK”+RF
2) PIN+FP(1:1)+PW+“OK”+RF
3) RF(1:N)+PW+“OK”+FP
4) PIN+ PW+“OK”+FP(1:1)+RF
PIN&FP& PW
PIN + FP + PW are verified
1) PIN+PW+“OK”+FP(1:1)
2) PIN+FP(1:1)+PW+“OK”
FP & RF/PIN
FP + PIN, or FP + RF are verified
1) RF+FP(1:1)
2) FP(1:N)+RF
3) PIN+FP(1:1)
FACE&FP&RF
FACE + FP + RF are verified
94
12. Appendix
1) FACE(1:N)+FP+RF
2) FP+FACE(1:1)+RF
3) RF(1:N)+FACE+FP
4) PIN+FP(1:1)+FACE+RF
5) PIN+FACE(1:1)+FP+RF
FACE&FP&PW
FACE + FP + PW are verified
1) FACE(1:N) +PW+“OK”+FP
2) FP+PW+“OK”+FACE(1:1)
3) PIN+FP(1:1) +PW+“OK”+FACE
4) PIN+FACE(1:1) +PW+“OK”+FP
5) PIN+PW+“OK”+FP+FACE
 Note: For combined verification, it is better to enroll all the elements in
need for using verification mode, or verification will fail.
For example: User “A” use fingerprint for enrollment, while password is used
for verification, then the user cannot pass the verification.
95
MultiBio700 User Manual
Appendix 5 Anti-Pass Back ★
【overview】
Sometimes, some illegal people follow the other one into the gate, which will
cause the security problems. To prevent such risks, this function is enabled.
The In record must match the Out record, or the gate won’t open.
This function needs two machines to work together. One is installed inside of
the door (master machine hereinafter), the other is installed outside of the
door (slave machine hereinafter). Wiegand signal communication is adopted
between the two machines.
【Working principle】
The master machine has Wiegand In and slave machine has Wiegand Out
functions. Connect Wigand Out of slave machine to Wiegand In of master
machine. Wiegand output from slave machine must not own machine ID. The
number sent to master machine from slave machine must be found in the
master machine.
【Function】
Judge whether it is anti-pass back according to user’s recent in-out record. In
record and out record must be matched. This machine supports out, in, or
96
12. Appendix
out-in anti-pass back.
When the master machine is set as “out anti-pass back”, if user wants to
come in and go out normally, his recent record must be “in”, or he cannot go
out. Any “out” attempt will be refused by “anti-pass back” function. For
example, a user’s recent record is “in”, his second record can be “out” or “in”.
His third record is based on his second record. Out record and in record must
match.(Notice: If customer has no record before, then he can come in but
cannot go out. )
When the master machine is set as “in anti-pass back”, if the user wants to
come in and go out normally, his recent record must be “out”, or he cannot go
out. Any out record will be “anti-pass back refused” by the system. (Notice: If
the customer has no former record, then he can go out, but cannot come in).
When the master machine is set as “out-in anti-pass back”, if the user wants
to come in and go out normally, if his recent record is “out” and “in”, then his
next record must be “in” and “out”.
【operation】
1. Select model
Master machine: The machine with Wiegand in function, except for F10
reader.
Slave machine: The machine with Wiegand Out function.
2. Menu setting
Anti-pass back
There are four options: in/out anti-pass back, out anti-pass back, in anti-pass
back, and none.
Out anti-pass back: Only user’s last record is in-record, can the door be
open.
In anti-pass back: Only user’s last record is out-record, can the door be
open.
Device status: There are three options: Control-in, control-out and none
97
MultiBio700 User Manual
Control-in: When it is set, the verified records on the device are in-records.
Control-out: When it is set, the verified records on the device are
out-records.
None: When it is set, close the device’s anti-pass back function.
3. Modify device’s Wiegand output format
When the two devices are communicating, only the Wiegand signals without
device ID are received. Enter device menu-> communication option->
Wiegand option or enter software -> basic setting -> device management ->
Wiegand, to modify “defined format” as “wiegand26 without device ID”.
4. Enroll user
The user must be on master machine and slave machine at the same time,
and user PIN must be the same. Therefore, it is necessary to enroll user on
master machine and slave machine at the same time.
5. Connection instruction
Wiegand communication is adopted for master machine and slave machine.
Refer to the following for connection:
Master
Slave
IND0
<----->
WD0
IND1
<----->
WD1
GND
<----->
GND
98
12. Appendix
Appendix 6 Statement on Human Rights and Privacy
Dear Customers:
Thank you for choosing the hybrid biometric products designed and
manufactured by us. As a world-renowned provider of biometric technologies
and services, we pay much attention to the compliance with the laws related
to human rights and privacy in every country while constantly performing
research and development.
We hereby make the following statements:
1.
All of our fingerprint recognition devices for civil use only collect the
characteristic points of fingerprints instead of the fingerprint images, and
therefore no privacy issues are involved.
2.
The characteristic points of fingerprints collected by our products cannot
be used to restore the original fingerprint images, and therefore no
privacy issues are involved.
3.
We, as the equipment provider, shall not be held legally accountable,
directly or indirectly, for any consequences arising due to the use of our
products.
4.
For any dispute involving the human rights or privacy when using our
products, please contact your employer directly.
Our fingerprint products for police use, or development tools support the
collection of the original fingerprint images. As for whether such a type of
fingerprint collection constitutes an infringement of your privacy, please
contact the government or the final equipment provider. We, as the original
equipment manufacturer, shall not be held legally accountable for any
infringement arising thereof.
The law of the People’s Republic of China has the following regulations
regarding the personal freedom:
99
MultiBio700 User Manual
1.
Unlawful arrest, detention or search of citizens of the People's Republic
of China is prohibited; infringement of individual privacy is prohibited.
2.
The personal dignity of citizens of the People's Republic of China is
inviolable.
3.
The home of citizens of the People's Republic of China is inviolable.
4.
The freedom and privacy of correspondence of citizens of the People's
Republic of China are protected by law.
At last we stress once again that biometrics, as an advanced recognition
technology, will be applied in a lot of sectors including e-commerce, banking,
insurance and legal affairs. Every year people around the globe suffer from
great loss due to the insecurity of passwords. The biometric products actually
provide adequate protection for your identity under a high security
environment.
100
12. Appendix
Appendix 7 Environment-Friendly Use Description
The Environment Friendly Use Period (EFUP) marked on this product refers to the
safety period of time in which the product is used under the conditions specified in
the product instructions without leakage of noxious and harmful substances.
The EFUP of this product does not cover the consumable parts that need to be
replaced on a regular basis such as batteries and so on. The EFUP of batteries is
5 years.
Names and Concentration of Toxic and Hazardous Substances or Elements
Parts Name
Toxic and Hazardous Substances or Elements
Pb
Hg
Cd
Cr6+
PBB
PBDE
Chip resistor
×
○
○
○
○
○
Chip capacitor
×
○
○
○
○
○
Chip inductor
×
○
○
○
○
○
Chip diode
×
○
○
○
○
○
ESD components
×
○
○
○
○
○
Buzzer
×
○
○
○
○
○
Adapter
×
○
○
○
○
○
Screws
○
○
○
×
○
○
○: Indicates that this toxic or hazardous substance contained in all of the homogeneous
materials for this part is below the limit requirement in SJ/T11363-2006.
×: Indicates that this toxic or hazardous substance contained in at least one of the
homogeneous materials for this part is above the limit requirement in SJ/T11363-2006.
Note: 80% of the parts in this product are manufactured with non-hazardous
environment-friendly materials. The hazardous substances or elements contained cannot be
replaced with environment-friendly materials at present due to technical or economical
constraints.
101
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement