Operating Guide - Beijer Electronics

Operating Guide - Beijer Electronics
Operating Guide
1
Introduction
3
PWS6600 comes with a 5.7” STN Liquid Crystal Display, and is water- and dust-resistant according to IP65.
The PWS is CE-marked and meets your need to be highly transient-resistant while in operation.
Also, its compact design makes connections with other machinery more flexible, thus achieving the optimal performance of your machines.
ADP is used to design applications of the PWS; it is reliable, user-friendly and compatible with many models.
The latest released ADP Version 6.1 and above can be used to design applications for the PWS.
2
System Menu
5
Set the dip switch SW7=ON. After the self-test, the system menu of the PWS is displayed on the screen:
Self Test
The bench test performs an overall hardware test and the function test lets the user select which item to be tested.
Human Machine Interface
ROM BIOS Version 2.1
Copyright 2011
256K Bytes
256K Bytes
512K Bytes
4M Bytes
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
11011111
8
Downloading an Application
Connect the RS232 port on the PC to the COM1 port on the PWS using a WPC-P8-42 cable. The connection
can also be made according to the illustration below.
PWS-COM1
9-pin male
Once the PWS is turned on, it will automatically execute a self-test to check its hardware. The result of a selftest is displayed on the LCD. See below for items to check in a self-test:
Display Type = Mono STN LCD
System RAM Size ...........
Video RAM Size ............
Battery Backed RAM Size ...
Application Memory Size ...
Working RAM Test ..........
Battery Status ............
BIOS ROM Checksum .........
Firmware Checksum .........
Application Checksum ......
RTC Function Test .........
Parameter Checksum ........
Communcation Port 1 Test ..
Communcation Port 2 Test ..
DIP Switches Setting(8..1)=
Bench and Function Tests
Set the dip switches SW3 and SW4=OFF to be able to run the bench and function tests for the PWS. Turn on
the PWS and the following screen will be displayed.
RXD
TXD
GND
RTS
CTS
PC COM RS232
9-pin female
2
3
5
7
8
Note:
The bench test will clear the application data of the PWS.
The functions of the commands are briefly explained below:
System Menu
6
Function
Setting Communication Parameters
There are two ways to configure working parameters; to set parameters in the PWS or in ADP.
To set parameters in the PWS, select F2 - Confg in the system menu.
Link
The PWS is connected.
F2 - Confg
Sets up the internal time clock and communication parameters in the PWS. All the settings
has to be made for the PWS to work properly.
Note:
Remember to set the dip switch SW5=ON if parameters are set in the PWS.
Use
field.
To set parameters in ADP, select Application / Workstation Setup. Then select the Connection tab to set communication parameters.
,
,
and
to move to desired field; + and - to set the value of the
F3 - Copy
Copies application data to the other same model of PWS.
F4 - Set
Calibrates the touch screen, adjusts LCD contrast and clears RAM data.
F5 - Run
Runs the application.
4
Note:
Remember to set the dip switch SW5=OFF if parameters are set in ADP.
7
Keypad
The six keys on the PWS include one menu key and five functional keys (F1 -F5). Press the menu key to slide
out the innovative slide-out menu. For further details on the slide-out menu please see the ADP User’s Manual
Menu Key
If any of tests does not pass the self-test, it will be noted with “Failed” next to the test item. Additionally, the
message “Error! Press screen to continue” will be displayed at the bottom of the screen.
If the power to the PWS or the PC was interrupted while downloading, Firmware checksum or Application
checksum will not pass the self-test, indicated by “Failed” in the self-test results after power is restored. If this
happens, the user can simply follow the download procedure to re-download the application or data. After
downloading again, all items should pass the self-test.
2
3
5
1
4
6
7
8
PWS ---- PC COM
RD
SD
SG
CD
DTR
DSR
RTS
CTS
PWS-COM2
25-pin male
TXD
RXD
GND
RTS
CTS
PC COM RS232
9-pin female
2
3
7
4
5
2
3
5
1
4
6
7
8
PWS ---- PC COM
RD
SD
SG
CD
DTR
DSR
RTS
CTS
Warning:
To avoid an electronic shock, be sure to switch off the power before connecting the download
cable to the PWS.
Set the dip switch SW7 = ON. After the self-test, the system menu will be displayed on the screen and the PWS
is ready to download the application.
Start ADP and open the application file to be downloaded. Make sure that the communication parameters are
correctly configured. Also remember to compile the file before downloading it. The file has to be compiled every
time a change has been made in the file before downloading it.
Then select Application/Download Firmware and then Application in ADP if it is a first time to download the
application to the PWS; otherwise, select Application/Download Application. The following appears on the
screen while the PWS is downloading:
Adjusting Touch Panel
1.
2.
Touch the upper-left and lower-right corners of the screen.
Next follow the route on the screen.
3.
Lastly touch the square on the center of the screen to complete the task.
Note:
Click Clear Data Ram of Set Key,the data stored in RAM will be erased.
F1-F5 Keys
When a key is pressed, the PWS will make a “beep” sound to signal that a command is pressed. (The default
setting is a 200 ms beep, and can be configured.)
9
10 Uploading / Downloading a Recipe
12 Setting a Password
Scenario 3: Password-protecting a button in the PWS
An application can also be uploaded from the PWS to the PC. Thus, a user can save an application as a *.V6F
file in ADP for future use.
Uploading an Application
Set the dip switch SW7 = ON. After the self-test, the system menu will be displayed on the screen and the PWS
is ready to upload/download a recipe.
Scenario 1: Requiring a password to start the PWS
Warning:
To avoid an electric shock, be sure to switch off the power before connecting the communication cable to the PWS.
Make sure that the PWS and the PC are connected according to section “Downloading an Application”. Set the
dip switch SW7 = ON. After the self-test, the system menu will be displayed on the screen and the PWS is ready
to upload the application.
Also make sure that communication parameters are correctly configured. Select File/Upload Application in
ADP and the Save As dialog box will appear on the screen. Enter the name of a firmware file (*.AF6) to save.
Click Save. Then the PWS will prompt for a password: enter the password set in ADP from Application/Workstation Setup. Once the correct password is entered, the PWS starts to upload the application to the PC. For
information about setting a password, please see section “Setting a Password“.
While the PWS is uploading, the following is displayed:
Uploading a Recipe
The ADP can create a button which is protected by a password for execution. For example, a Goto Screen button can be designed with a high level of security; which means that a password with a high level of privilege is
required in order to open the other screen. As the button is selected and the current user has a lower privilege
than has been set for the button, the PWS will prompt the user for a password. The user will need a password
with at least the level of privilege that has been set for the button. This function can restrict users to access to
certain parts of the application.
Select File/Upload Recipes in ADP and the Save As dialog box will appear on the screen. Enter the name of a
recipe file (*.RCP) to save. Click Save. While the PWS is uploading the recipe, Uploading recipes is displayed
on the screen.
Note:
When using the PWS for the first time, make sure to first run the application once, or else the
upload function will not work.
Scenario 4: Requiring a password to copy or upload application
Downloading a Recipe
When selecting F3 - Copy in the system menu or File/Upload Application in ADP, the PWS will prompt for a
password. The user will need to enter the correct password to copy an application from one PWS to another.
Note that setting this password is different from the passwords set in Scenarios 1-3. To set this password, select
Application/Workstation Setup in ADP. Under the Password tab, the project designer is able to set the password.
Open an application file with the recipe to be downloaded in ADP. Select File/Download Recipes to display the
Open dialog. Enter the name of the recipe file (*.RCP) and click Open. While the PWS is downloading the
recipe, Downloading recipes is displayed on the screen:
Uploading recipes
Link
After uploading, select File/Reconstruct Source in ADP to display the Open dialog. Open the uploaded application file (*.C64 or *.AA6). The application screen will be displayed on the PC monitor. Finally, select File/
Save As to save the application as a *.V6F file. Thus a source file can serve the purposes of maintenance and
modification.
If the dip switch SW6 = ON, the user needs to enter a password to start the PWS. For this purpose, the designer
can use the object Action Button in ADP to create a button which displays the password table on the PWS display. A user with the right to access the table can register passwords and user levels in the table.
Downloading recipes
Link
After the download is finished, select F5 - Run to run the application.
Remember to define the length and the number of recipes in the application. Also remember to upload the format of recipes from the PWS
before starting to edit a new set of recipe data in the PC.
For further information about creating/editing recipes, please see the corresponding chapter in the ADP User’s
Manual.
11 Copying an Application
To copy an application from one PWS to another, select F3 - Copy from the system menu. Set the dip switch
SW7 = ON and connect the two PWSs with a download cable. After the self-test, the system menu will be displayed on the screen.
Select F3 - Copy in the system menu from the PWS with the application to be copied. The PWS will prompt
for a password: enter the password set in ADP from Application/Workstation Setup. Once the correct password
is entered, the PWS will start to copy the application between the two PWSs.
In the illustration above, the TBL-button is an action button used to display the password table. When the button is selected the password table is displayed on the screen for a user with the right to access the table. Touch
the password to highlight an area for entering a value.
How to configure an Action Button is described in the ADP User’s Manual.
After registering passwords and user levels, set the dip switch SW6 = ON (i.e. password required). Restart the
PWS and after the self-test the user will be prompted to enter a password in order to run the PWS. The PWS
will determine the user level from the entered password. For instance, if the level of the password entered by the
user is 2, then the PWS will set the user level to 2. User level 1 has the highest privilege and User level 9 has the
lowest.
Note:
Only users of User Level 1 has the right of access to the password table.
Scenario 2: Re-entering a password
The object Action Button in ADP also allows the designer to create a button which asks the user to re-enter a
password. For example, by pressing the PSW-button the password keypad will be displayed to prompt the user
to enter a password. After entering the password, the PWS will update the user level according to the most recent
password which has been entered. Therefore, this button can be applied to raise or drop one’s privileges while
the PWS is in operation.
The following appears on the screens during the copying:
Note:
When copying for the first time,make sure to first run the application once, or else the copy
function will not work.
How to configure an Action Button is described in the ADP User’s Manual.
Beijer Electronics AB
Box 426
SE-201 24 Malmö, Sweden
Tel: +46 40 35 86 00
Fax: +46 40 93 23 01
www.beijerelectronics.com
Beijer Electronics Corp.
8F., No.108, Minquan Rd., Xindian Dist.,
New Taipei City 23141, Taiwan (R.O.C.)
Tel: +886-2-2218-3600
Fax: +886-2-2218-9547
www.beijerelectronics.com.tw
07/25/2011/V.6 660018+06
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement