ZN ‐ D100VE Installation Manual
INFORMATION TO USER
CAUTION
RISK OF ELECTRIC SHOCK,
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SEERIVCE PERSONEL.
!
!
This symbol is intended to alert the user to the presence of un ‐ insulated
“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
2010/2 ‐ 1 03A.02
2
ZN ‐ D100VE Installation Manual
Table of Contents
1.
FEATURES ............................................................................................................... 4
2.
PACKAGE CONTENTS .............................................................................................. 5
3.
PART NAMES .......................................................................................................... 6
4.
INSTALLATION ........................................................................................................ 7
4.1.
Installation Template ......................................................................................................... 8
4.2.
Manual adjustment for 3 ‐ axis movements ........................................................................ 8
4.3.
Lens Focus Adjustment ...................................................................................................... 9
4.4.
Setting the Image Attribute................................................................................................ 9
5.
CONNECTIONS ...................................................................................................... 10
6.
CONFIGURATION .................................................................................................. 11
6.1.Set
up network environment ............................................................................................ 11
6.2.View
video on web page ................................................................................................... 11
6.2.1.View
video using ZNS ‐ GIT IPAdmin Tool .................................................................... 11
6.2.2.View
video using IP address ....................................................................................... 14
6.3.
Reset................................................................................................................................. 14
6.4.
Factory Default................................................................................................................. 14
APPENDIX (A): SPECIFICATIONS ................................................................................ 15
Summary ................................................................................................................................. 15
Electrical Characteristics ......................................................................................................... 16
Environment Condition ........................................................................................................... 16
VCA (Video Content Analysis) ................................................................................................. 17
APPENDIX (B): DIMENSIONS..................................................................................... 18
APPENDIX (D): TROUBLE SHOOTING......................................................................... 19
Checking your Firmware ......................................................................................................... 19
Support.................................................................................................................................... 19
2010/2 ‐ 1 03A.02
3
ZN ‐ D100VE Installation Manual
1. FEATURES
Camera
•
Indoor Fixed Mini Dome IP Camera
•
High Quality Compression in real time streaming
•
1/4” VGA CMOS
Streaming
•
Dual streaming mode (such as different codec/resolution/bit rate and so on.)
•
De ‐ interlacing on DSP
•
Burnt ‐ in text supported
•
Unicast/Multicast supported
Video/Audio
•
Video compression: H.264/MPEG4/MJPEG (30FPS@D1)
•
Audio compression: G.711(µLaw, aLaw)/PCM
•
Video Motion Detection supported
•
2 ‐ way mono audio supported
Network
•
RTSP/ HTTP protocol supported
•
10/100 Base ‐ T Ethernet
Additional Features
•
Built ‐ in Video Content Analysis
•
OSD supported
•
SDK (Software Development Kit) provided
VCA (Video Content Analysis)
•
VCA Presence (Included as basic)
•
VCA Surveillance (Optional)
2010/2 ‐ 1 03A.02
4
ZN ‐ D100VE Installation Manual
2. PACKAGE CONTENTS
Unpack carefully and handle the equipment with care.
The packaging contains:
ZN ‐ D100VE DC power adaptor
Extension cable
(for LAN, power connector, and audio )
Quick Installation Guide
Installation Template
Screws and Anchor block
Hex wrench driver
i
Note
The above contents are subject to change without prior notice.
2010/2 ‐ 1 03A.02
5
ZN ‐ D100VE Installation Manual
3. PART NAMES
①
②
③
* Models herein and their appearance are subject to change without any prior notice.
① LAN Connector (Ethernet)
This is a RJ45 LAN connector for 10/100 Base ‐ T Ethernet.
② Audio in/ out Cable
ZN ‐ D100VE has a mono audio input and a mono audio output.
③ Power Adaptor Connector (DC 12V)
ZN ‐ D100VE needs a DC 12V 1A adapter for power supply.
2010/2 ‐ 1 03A.02
6
ZN ‐ D100VE Installation Manual
4. INSTALLATION
1) Connect the LAN cable, power supply cable, and the video loop out cable
with the ZN ‐ D100VE.
2) Place the installation template on the
ceiling.
3) Drill two holes on the template and insert anchor blocks into the holes.
Fasten the ZN ‐ D100VE with screws.
4) Put the dome cover on the main
body of the ZN ‐ D100VE.
Make sure the main body and the cover fit each other into place.
i
When assembling the main body of the ZN ‐ D100VE and its dome cover, make sure they fit each other into place.
Note
!
Caution
The ZN ‐ D100VE may fall off the ceiling even after the proper installation and mounting.
To prevent any accident, make sure the ceiling is firm and stable enough to support the ZN ‐ D100VE.
If any reinforcement is needed, consult with your safety personnel and proceed with the installation.
2010/2 ‐ 1 03A.02
7
ZN ‐ D100VE Installation Manual
4.1. Installation Template
2 ‐ Ø6
Ø30
Ø125
4.2. Manual adjustment for 3-axis movements
After installation, make a manual adjustment on the inner liner.
Perform 3 ‐ axis movements manually by turning the inner liner to different directions as above, and check if it moves properly.
After adjustment, fasten the screw of the rotation axis.
2010/2 ‐ 1 03A.02
8
ZN ‐ D100VE Installation Manual
4.3. Lens Focus Adjustment
A
D
E
C
1) Open the dome cover from the device.
2) Uncover the latch(C) carefully to remove the lens cover.
3) Rotate the lens focus ring(D) to adjust the focus and fasten the screw(E) using the included hex wrench.
4) Push the lens cover to the module until the latch(C) clicks into position.
5) Attach the dome cover by aligning protrusion on the body (B) with the inverted triangle mark of the dome cover (A).
Turn the dome cover clockwise to lock.
* Models herein and their appearance are subject to change without any prior notice.
4.4. Setting the Image Attribute
You can set the image attribute of camera through the webpage.
The menu of image attribute can be seen under Setup > Video & Audio > Video ‐ in > Attribute
Setting .
Brightness, contrast, hue, saturation and sharpness can be adjusted.
2010/2 ‐ 1 03A.02
9
ZN ‐ D100VE Installation Manual
5. CONNECTIONS
LAN
DC 12V
!
Caution
Make sure the polarity is correct.
Incorrect connection may cause malfunction or damage to the IP device.
!
Caution
Power Adaptor Connector (DC 12V)
2010/2 ‐ 1 03A.02
10
ZN ‐ D100VE Installation Manual
6. CONFIGURATION
6.1.Set up network environment
The default IP address of your IP device is 192.168.XXX.XXX.
You can find the available IP address from the MAC address of your device.
Please make sure the device and your PC are on the same network segment before running the installation.
If the network segment between your PC and the device is different, change your PC’s settings as below.
IP address : 192.168.xxx.xxx
Subnet mask: 255.255.0.0
6.2.View video on web page
View the live video on a web page using your IP device and its IP address.
You can use the ZNS ‐
GIT IPAdminTool or enter the IP address on the web page.
6.2.1.View video using ZNS-GIT IPAdmin Tool
ZNS ‐ GIT IPAdminTool automatically searches all activated GANZ network camera and encoder series and shows the product name, IP address, MAC address and etc.
ZNS ‐ GIT IPAdminTool is
provided with SDK at the following SDK path.
{SDK root}\BIN\TOOLS\AdminTool\
2010/2 ‐ 1 03A.02
11
ZN ‐ D100VE Installation Manual
To use the ZNS ‐ GIT IPAdminTool and view the live video on a web page:
1.
Start ZNS ‐ GIT IPAdminTool.
Names and info of currently activated devices appear as a list.
2.
Right ‐ click on the desired device and select Web view .
3.
Select Continue to this website on the Security Certificate Alert page.
(The explanation and captured images at this manual are mainly on the basis of Internet
Explorer 7.0)
4.
Click pop ‐ up blocked and install the ActiveX control as below.
You need to install the
ActiveX for displaying the images.
2010/2 ‐ 1 03A.02
12
ZN ‐ D100VE Installation Manual
5.
Wait for a few seconds while the web page loads.
The live video is displayed as below.
6.
If the live video is not displayed and “Can not Create XMLDOMDocument Install
MSXML4.0” message is shown as below, please download and Install from the link below.
http://www.microsoft.com/downloads/details.aspx?familyid=3144B72B ‐ B4F2 ‐ 46DA ‐
B4B6 ‐ C5D7485F2B42&displaylang=en
(VCA Library requires MS XML 4.0
library which is an xml parser made by Microsoft.)
2010/2 ‐ 1 03A.02
13
ZN ‐ D100VE Installation Manual
6.2.2.View video using IP address
View the live video on a web page using your IP device and its IP address.
To have the correct
IP address ready and use it on a web page:
1.
Convert a MAC address to an IP address or check the IP address on the ZNS ‐ GIT IPAdminTool.
(The MAC address is attached on the side or bottom of the device.)
MAC address = 00 ‐ 1C ‐ B8 ‐ C0 ‐ 14 ‐ B1 → IP address = 192.168.20.177
the Hexadecimal number to Decimal number.
2.
Open a web browser and enter the IP address of the device.
3.
Click Continue to this website on the Security Certificate Alert page.
4.
Click pop ‐ up blocked and install the ActiveX control.
You need to install the ActiveX for displaying the images.
5.
Wait for a few seconds while the web page loads.
The live video is displayed.
6.3. Reset
Hardware Reset is NOT supported.
(Software Reset is available.)
6.4. Factory Default
Hardware Factory Reset is NOT supported.
(Software Factory Reset is available.)
2010/2 ‐ 1 03A.02
14
ZN ‐ D100VE Installation Manual
APPENDIX (A): SPECIFICATIONS
Summary
Camera Module
Image Sensor
CMOS
Effective Pixels
Scanning system
Horizontal
Resolution
Min.
Illumination
1/4” VGA CMOS
640 x 480
Progressive Scan
550 TV Lines
Lens
Day & Night
3 Lux Color
0.1
Lux DSS On
Focal Length 3.6
mm, F.# 2.0, Board type,
Lens for Security Camera
Not Supported
Video
Compression Format H.264, MPEG ‐ 4, MJPEG Selectable per Stream
Number of Streams
Resolution
Compression FPS
Deinterlacing
Motion Detection
OSD
Dual Stream, Configurable
D1
*1
, 4CIF
*1
, VGA, CIF, QCIF
30 fps
Supported (DSP)
Supported
Supported (DSP)
Burnt ‐ in Text (Digital)
Output
Audio
Input/output
Compression Format
Function
Digital Input/output
Supported (DSP)
Not Available
1/1 channel
G.711
Network
Power over Ethernet
Not Supported
10/100 Base ‐ T
Not Available
Protocol
Material
TCP/IP, UDP/IP, HTTP, RTSP, RTCP, RTP/UDP, RTP/TCP,
SNTP, mDNS, UPnP, SMTP, SOCK, IGMP, DHCP,
FTP, DDNS, SSL v2/v3, IEEE 802.1X, SSH
Polycarbonate
Dimensions
Color
*1.
These image sizes are scaled up resolutions.
Housing: 124(D) x 100(H) mm,
Dome: 100.0( Ф ) mm
White
2010/2 ‐ 1 03A.02
15
ZN ‐ D100VE Installation Manual
Electrical Characteristics
Video Output
Audio Input
Audio Output
Power Source(Approx)
1Vp ‐ p, 75 Ω
Linein, 1.43Vp
‐ p(Min 1.35Vp
‐ p, max 1.49
Vp ‐ p), 39 K Ω
Lineout, 46mW Power, 16 Ω
12 V DC 290 mA
Environment Condition
Operating Temperature
Operating Humidity
0 ˚ C ~ 50 ˚ C (32 ˚ F ~ 122 ˚ F)
Up to 85% RH
2010/2 ‐ 1 03A.02
16
ZN ‐ D100VE Installation Manual
VCA (Video Content Analysis)
VCA Presence (Included as Standard)
High Performance Advanced Tracking Algorithm, Low False Alarm Rate
Easy to Use
Detection Zones
On ‐ screen Display
Intuitive
Multi ‐
Web segment
Browser
Interface
Polygons and
Lines
Burnt ‐ in Annotation
Real ‐ time Display of Tracking Data and Events
Stream or Analog video out
( ※ Analog video out support can vary depending on the device model and hardware version and the firmware version)
VCA Surveillance (Optional)
Detection Behavior
Camera Tampering, Direction, Stopping, Loitering, Entering,
Exiting, Appear, and Disappear Filters
3D Behavior Perspective Corrected Size and Speed Filters
Statistics
Meta Data
Image Stabilization (Optional)
Electronic Stabilization
Counting Functions and Other Statistics
Binary XML Format
Removes Camera Sway
2010/2 ‐ 1 03A.02
17
ZN ‐ D100VE Installation Manual
APPENDIX (B): DIMENSIONS
Ø124
R50
2010/2 ‐ 1 03A.02
(Unit: mm)
18
ZN ‐ D100VE Installation Manual
APPENDIX (D): TROUBLE SHOOTING
Checking your Firmware
Firmware is software that determines the functionality of the device.
One of your first actions when troubleshooting a problem should be to check the currently installed version.
The latest version may contain a correction that fixes your particular problem.
The current firmware version in your device can be seen under Setup > About > Version
New firmware can be downloaded at the FTP site.
When you download firmware from the FTP, your product will receive the latest available functionality.
Always read the upgrade instructions and release notes available with each new release, before updating the firmware.
Please contact us to get an FTP account.
Support
If you cannot resolve an issue, for additional assistance, please contact your supplier or system integrator .
If you contact our support, please help us help you resolve your problems expediently by
providing a server report, log file and a brief description of the problem.
1.
In the address bar of your browser, after the unit IP address enter following CGI command.
<IP ADDRESS> /nvc ‐ cgi/admin/param.cgi?action=list
The server report contains important information about the device, as well as a list of the current parameters.
2.
The Log messages in the device can prove a useful diagnostic tool for troubleshooting.
Go to Setup > Maintenance > System Log > LOG LIST > message.
2010/2 ‐ 1 03A.02
19
