NADAIR Central Vacuum System

User Manual

Model Number:

V700AL

V600AL

1.

IMPORTANT SAFETY INSTRUCTIONS

CAREFULLY READ ALL OF THESE INSTRUCTIONS

PRIOR TO USE THIS CENTRAL VACUUM SYSTEM

When using an electrical appliance, it is necessary to obey certain basic precautions

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:

- Unplug the power cord from electrical outlet before proceeding with any unit maintenance.

- Do not install outdoors, always have it protected from weather and do not use on wet surfaces.

- This appliance must not be used as if it is a toy. It is therefore necessary to be very prudent when the system is used by children or when in use in the proximity of a child or infant.

- This system must be used in conformity with the instructions provided in this manual. Only use the accessories recommended by the manufacturer.

- Do not use the system if the power cord or if the electrical outlet are damaged, if the system does not function normally, if it was dropped, was left outdoors in bad weather for an extended period of time or if it was immersed in liquid, the power unit must be sent to an authorized service agent.

- Do not use the power cord to pull or lift the power unit, nor use it like a handle. Be careful not to pinch it in a door, do not let it hang on a sharp corners or edges.

- Examine the openings for foreign objects which may have remained in the pipe. If any, remove the obstructing objects to ensure maximum airflow.

- Keep the power cord from any contact with any warm objects or surfaces.

- Do not unplug the power cord by pulling on it, always remove directly at the electrical oulet.

- Do not use the system or its accessories with wet hands.

- Keep hair, clothing, fingers, any other body parts or other objects out of or away from any openings or moving parts of the system.

- All functions of the system must be deactivated prior to removing the power cord from the electrical socket.

- Do not use the system to pick up flammable liquids or fuels (i.e. gasoline), nor use the system in areas where such liquids may be present.

- Only plug in the power cord into properly grounded electrical sockets. For more information on this subject, please see ‘’Grounding specifications’’ in section 2.

- The exhaust of the power unit must not be right against a wall, a ceiling or be inside a closed space inside a building or structure. It is recommended that the exhaust be vented outdoors.

- Do not pick up hot ashes, red ambers, smoking hot material, incandescent material, cigarette butts, matches etc...

- Do not put anything on top of the power unit or near it, because this could cause the unit to overheat

- DO NOT use the power unit if the pipe network is clogged, this will cause the unit to overheat.

KEEP THESE INSTRUCTIONS IN A SAFE PLACE

THIS POWER UNIT IS FOR DOMESTIC USE ONLY

2. GENERAL DIRECTIVES AND REFERENCES

ELECTRICAL GROUNDING SPECIFICATIONS

The system’s power unit must absolutely be grounded. In the event of a malfunction or a power unit failure, the grounding provides the path of least resistance to any electrical current, minimizing the risk of electric shock. The power unit’s power cord has a length of

65’’ (1,65m) and is fitted with a grounding wire and grounding pin. The power unit‘s power cord must always be directly plugged into a suitable electrical outlet which is itself properly installed and properly grounded, in conformity with the current local electrical standards.

Do not use extension cord(s) to connect the power unit to the electrical outlet.

WARNING

Improper connection of the power unit grounding wire can result in the risk of electric shock.

If you are in doubt of a proper grounding, contact a professional electrician. Do not modify the power cord supplied with this power unit. If this power cord connector does not fit your electrical outlet, have the proper electrical outlet installed by a professional electrician. This power unit is designed to be used on a nominal electrical circuit of 10 A. 220-240 V in 50-60

Hz . The power cord is fitted with a grounding pin. Make certain that the power cord is plugged into an electrical outlet having the same specifications. This appliance should be used without an adaptor. This power unit should be installed on its own independent circuit and breaker.

IMPORTANT

The manufacturer shall not be held responsible for damages cause by the inappropriate use of this system. The warranty does not cover the damages caused by an inappropriate use of this system nor the problems resulting from an installation which does not meet the specifications, nor any structural or functional alterations made to the power unit. An inappropriate, not-recommended installation of the system or the power unit made without respecting the directives of this document will equally be considered as misuse. All conditions and restrictions are set forth in the limited warranty and in the user manual. To optimize the performances and the life of your central vacuum system, it is important to do regular maintenance and cleaning of the filter according to the guidelines listed in this user manual.

General guidelines to be respected at all time

1. The power unit must be installed in a well ventilated area, protected from weather and away from all sources of heat.

2. This central vacuum system is design for dry surfaces only and must not be used on wet surfaces nor be used in any circumstances to pick up liquids or to clean wet carpets or any wet ground.

3. The filter cage must be covered at all times by the permanent filter during operation of the system.

4. The motor housing must never be obstructed in any way to prevent damaging or overheating.

5. Do not use this system to pick up mud or similar substances. To vacuum baking flower, talcum powder, cement or gypsum dust, will have for effect to obstruct and clog the filter media; you have to clean the filter several time during and after such pick-ups. Otherwise the motor will overheat and may be damaged.

6. Do not attempt to shorten or modify the power cord in any way.

7. As a safety measure, unplug the power cord prior to proceed to maintenance or servicing.

8. In order for the warranty to remain valid; any repairs or servicing on the power unit must only be performed by an authorized service centre.

9. The position of the power unit must be so, that the power cord and electrical outlet are always easily accessible.

10. Pertaining to the use of an electrified valve (110 VAC) (intended for the connection of a current carrying hose and electrically motorised brush):

-Only connect a current carrying hose to this wall valve

-Do not install a current carrying valve outdoors

-Do not use a damaged hose, bring in the hose for repair at an authorized service centre.

3. MODELS

Air ‐ Debris Intake

Disposable  

Filtration Bag 

NOTE

APPLICABLE TO ALL POWER UNITS: In order to avoid overheating, we recommend that 30cm of clearance be kept all around the power unit.

4. SYSTEM OPERATING INSTRUCTIONS

Your new system is now ready to be used. Here are a few simple guidelines to follow when you are using your Central Vacuum System: Insert the wall end of the hose into one of the vacuum valves installed throughout your home and you are ready to start.

NOTE

In regards to the low voltage system: All vacuum inlet valves are fitted with two spring loaded metal pins (see inside the valve opening). When the two metal parts of the hose wall end are in contact with the two pins inside the valve, the system is energized. You may now turn it on or off from the hose handle switch (if this option was selected).

The low voltage cable is connected in parallel from every valve, it runs all along the pipe network and brings the power to the remote switch so to remotely start or stop the power unit in all safety.

A standard flexible hose, not fitted with an interrupter, will start the power unit as soon as it is inserted in the valve opening.

5. SYSTEM MAINTENANCE

FILTRATION SYSTEM

In order to maintain optimal air quality in your home, the power unit comes supplied with a high efficiency HYBRID filtering system. The washable and reusable permanent filter and a disposable filtration -bag. The permanent filter must be in place at all times, the filter securing strap must be tightened just so as to insure no fly-by of debris into the motor housing.

IMPORTANT

This unit can be used with or without disposable filtration -bag. The disposable bag installs as shown here :

1- Remove the debris canister.

2- Remove the dirt filled bag.

3- Install the new bag by twisting it.

4- Verify and clean (if necessary)the permanent filter.

5- Replace the debris canister and secure the latches.

NOTE

When replacing the disposable bag, make sure that the rubber diaphragm is correctly installed onto the intake PVC pipe. Make sure that the bag is not cut or damaged. Make sure that the canister is secured in place prior to restarting the power unit. It is recommended to replace the disposable bag or to empty the debris canister as well as to clean the permanent filter 3 or 4 times per year. If the system is used more frequently than normal, repeat the above procedure more often.

IMPORTANT

NEVER USE this system to pick up liquids, mud or combustible materials. To vacuum baking flower, talcum powder, cement or plaster dust you will have to clean the filter several time during and after such pick-ups. Otherwise the power unit performances will be affected, the motor will overheat and may be damaged.

MOTOR

This power unit is equipped with a soft-start controller and a delayed stop. A warning is automatically programmed after 500 hours of usage. The inspection and the maintenance of this appliance must be done in an authorized service centre or by an authorised service agent. A Mini-breaker shall cutt-off power to protect the motor in the event of a power surge which may cause the motor to overheat. The low voltage technology system communicates the power unit status through a muticolor LED on the side of the unit. Please consult the interpretation chart in section 8.

6. TROUBLESHOOTING

GENERAL

The following may cause failure of the power unit:

- Inadequate electrical power (Voltage or Amperage), verify that the electrical power supplied complies with the power unit’s requirement.

- Abnormal performances of the electronic control module or the motor.

Before calling a service technician, in case of a malfunction, please review the following situations by running the following simple diagnostics:

SITUATION VERIFICATION

THE POWER UNIT DOES NOT

OPERATE

Verify that there is power in the electrical outlet.

Verify the breaker or the fuse in the electrical panel.

Verify that the power cord is adequately plugged into the electrical outlet.

Verify that all low voltage connections are adequate at every valve location. Open every valve, one at a time, and make contact between the two small pins with a metal object. If all the valves work properly, take a look at the low voltage circuit or switch on the hose.

If the power unit still does not work after the above diagnostic, bring the unit to the nearest authorized service centre or agent.

SITUATION VERIFICATION

LOW OR NO SUCTION OR AIR FLOW AT ALL  Verify the cleaning tool or the hose for possible obstruction. If the hose is obstructed, try to

“massage” the clog out. Try to “reverse” the hose by inserting the cleaning end of the hose in the wall valve and making contact with the two (2) small metal contact pins, hold your hand around the opening for air tightness.

Verify if the disposable bag is full, if so replace disposable bag and/or that the filter may be clogged, if so clean the permanent filter.

Verify if the debris canister is adequately placed on the unit with no air leaks.

Verify that all other valves are shut and that there is no air leaks.

If one of the vacuum valves has noticeably less power than the others, it is a sign of a clog at this particular valve. Write a different number on a few paper tissues and pick one up in every valve in the home; see in the debris canister which one is missing so to find which valve is obstructed.

If none of the valves function properly and the power unit is running; unhook the flexible pipe on the top of the power unit from the debris intake line. If you have plenty of power there, it is a sign that the clog is between the last valve and the power unit.

If the power unit still does not work after the above diagnostic, bring the unit to the nearest authorized service centre or agent.

7. LOW VOLTAGE SYSTEM TECHNOLOGY

LED status interpretation guide

This Central Vacuum Power Unit is provided with an LED status indicator to keep you informed on the different states and functions during its operation. Reading the following table will allow you to identify the status of your appliance by the different behaviours of the LED.

STATUS COLOUR LEGEND

OFF The power cord is unplugged – No power.

GREEN The power cord has just been plugged-in or the power has been restored. The LED will flash rapidly for a few seconds and will then

GREEN

AMBER

RED

RED become solid again

.

The power unit is operational.

Stop the power unit, replace the bag and clean the permanent filter if required (after 15 hours of usage), reboot the unit by pressing the small button for 5 seconds. The LED will return to

.

The 500 hours motor inspection is now required, otherwise the motor may get damaged.

Stop the power unit and have service done on the unit immediately at an authorized service center.

Slow blinking LED Fast blinking LED Solid – No blinking  

8. SAFETY NOTES

-Make certain that the work area is safe and clear prior to installing your new Central Vacuum Power

Unit.

-Wear the necessary safety clothing & equipment prior to start any work i.e goggles, gloves etc.

-Use the right tools & in good working order:

- Hammer

- Phillips head screwdriver

- Measuring tape

- Level

- Drill; with wood or concrete bit of 10mm

- Pliers

- Wire stripper

For future references, take note of the following information:

Serial number:____________________________________________

Date of purchase: _________________________________________

Purchased at: _____________________________________________

Please keep a copy of your invoice together with this manual

Cleanstar Pty Ltd

ABN: 51 121 002 104 ACN: 121 002 104

59 Radford Road, Reservoir VICTORIA 3073

Phone: (03) 9460 5655 Fax: (03) 9460 5666

Email: [email protected]

Web: www.cleanstar.com.au

CONDITIONS OF WARRANTY

This document outlines the terms and conditions of warranty for your Nadair product. This is an important document that should be kept with your proof of purchase documents in a safe place for future reference should you require service for your product.

Thank you for purchasing your new Nadair product. We are confident this product will give you trouble-free use and excellent service, provided the operator uses and maintains the product in accordance with the Instruction Manual. Please read the Instruction Manual carefully before using the product for correct operation and maintenance procedures, and store it in a safe place for future reference.

1. This is a parts and labour warranty against faulty or defective parts, materials or workmanship in manufacturing, when the product is used and operated in accordance with the Instruction Manual.

2. This product carries a 5 year warranty period that commences from the original date of purchase by the first user/purchaser, and is not transferable.

3. The warranty covers only personal, domestic or household use of the product to remove dry dirt and dust from household carpets, flooring and fabrics.

4. This product is not suitable for commercial or industrial cleaning applications and therefore no warranty applies in this case.

5. This warranty only applies to products purchased and used in Australia.

6. At all times during the warranty period, Cleanstar shall, at its sole discretion, determine whether repair, replacement or refund will apply if the product has a valid warranty claim applicable to it.

7. The repair or replacement of the product under this warranty does not extend the original period of warranty.

8. Please note that this warranty will be voided in the following cases (which are not exhaustive) and the warranty does not apply to the cost of replacing any parts of the product resulting from:

• Accidental damage;

• Normal wear and tear;

• Neglect, misuse or physical abuse by the operator, including failure to properly maintain or service;

• Any alterations, modifications or tampering with the product without the prior written consent of Cleanstar;

• Incomplete or improper installation;

• Incorrect, improper or inappropriate operation;

• Insect or vermin infestation;

• Power surges, electrical storm damage or incorrect power supply/voltage;

• Excessive use or use for which this product has not been designed;

• Vacuuming up water, liquids, toner, powders, glass, hazardous, flammable or corrosive materials, plaster dust, concrete dust and other similar building or construction materials;

• Failure to comply with the operating instructions contained in the Manual supplied with the product;

• If the product is rented;

• If the product is used outside of Australia;

• If the product was serviced or repaired by anyone other than Cleanstar, or one of Cleanstar’s Authorised Service Agents (ASA).

Cleanstar is unable to accept any responsibility under this warranty for any repair work not carried out by an ASA or from the use of non-genuine parts.

9. This warranty does not cover service calls, travelling time or consumable parts such as belts, dust bags, filters, hose or hose parts, rods and wands, floor tools and accessories, motor brushes and other like consumable items, unless defective in manufacture. In order to prolong the life of accessories and consumables, regular care and maintenance is recommended.

10. Please retain your original proof of purchase which will be required before you can make a claim under this warranty. If proof of purchase can not be provided at the time of a warranty claim or service, any work carried out on the cleaner is chargeable.

11. Any transportation and delivery costs involved in the repair of defective parts shall be borne by the claimant. In all instances, unless the product is transported by Cleanstar or a Cleanstar authorised representative, the product is transported at the owner’s cost and risk while in transit to and from Cleanstar or its ASA.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The benefits conferred by this warranty are in addition to other rights and remedies under law in respect of the product to which this warranty relates.

TO INQUIRE ABOUT MAKING A CLAIM UNDER THIS WARRANTY, PLEASE FOLLOW THESE STEPS: a) carefully check the Instruction Manual and the terms of this warranty; b) have the name and model number of the appliance available; c) have the proof of purchase available (ie. invoice, receipt, etc) showing where the appliance was purchased from and date of purchase; d) call Cleanstar on (03) 9460 5655 to speak to one of our customer service staff.