35

COMMERCIAL GRADE WET-DRY-BLOW VACUUMING SYSTEM

USER GUIDE

Congratulations on purchasing a Bennett Read

Tough 35 wet & dry vacuum cleaner.

This product is packed with the power and technology to provide fast and efficient cleaning. It is manufactured to the highest quality and is backed by a one year guarantee by Tevo.

Should you need any support from us, please visit: www.tevo.co.za or call 0861 77 88 88.

3

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS

BEFORE USING YOUR VACUUM.

When using your Tough 35, basic safety precautions should be observed, including the following:

!

WARNING

TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK, OR INJURY:

» Use the system only for its intended use

» To protect against a risk of electric shock, do not immerse any part of the system in water or other liquids

» Do not allow cord to touch hot surfaces

» Do not run appliance over cord

» Do not operate the system with a damaged cord or plug, or if the appliance or any other part of the system has been dropped or damaged. To avoid the risk of electric shock, do not disassemble or attempt to repair the Tough 35. Return the unit for examination and repair. Incorrect reassembly or repair can cause a risk of electrical shock or injury and will not be covered by the guarantee

» Keep hair, loose clothing, fingers and all parts of body away from openings and moving parts

» Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present

» Do not pick up anything that is burning or smoking such as cigarettes, matches or hot ashes

» Use extra care when cleaning on stairs

» Do not use the Tough 35 without the

Microparticle filter in place, except when vacuuming up liquids. Refer to page 6 for operating instructions

» When using as a Wet Vacuum take caution not to over-fill the tank with liquid to avoid risk of electrical shock and damage to your Tough 35. Refer to page

6 of this manual for instructions

» This appliance is intended for commercial and/or domestic use only. Follow all user instructions in this manual

» Do not leave the Tough 35 plugged in when unattended

» Unplug the electrical cord when not in use and before servicing

» Not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge

» Do not allow to be used as a toy

» Close attention is necessary when used near children, pets or plants

» Children should be supervised to ensure that they do not play with the appliance

» Use only as described in this manual. Use only manufacturer’s recommended accessories

» Do not pull cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners.

» Turn off all controls as applicable before unplugging from electrical outlet

» Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord

» Do not handle plug or vacuum with wet hands or operate without shoes

» Do not put any objects into openings.

» Do not use with any opening blocked

» Keep free of dust, lint, hair and anything else that may reduce airflow

» Store your Tough 35 indoors in a cool, dry area

» Keep your work area well lit

» Keep end of hose, wands and other openings away from your face and body

» Using improper voltage may result in damage to the motor and possible injury to the user.

Correct voltage is listed on rating label. For operation on a 220-240V, 50/60Hz power supply only

» Use only identical replacement parts

» See instructions for Servicing of

Double-Insulated Appliances

WARNING:

» To reduce the risk of injury from moving

parts – Unplug before servicing

» To reduce the risk of electric shock –

Unplug before cleaning or servicing

» Do not use outdoors

SAVE THESE INSTRUCTIONS

FOR FUTURE USE.

4

PRODUCT VIEW

1. On/off Switch

2. Vacuum Function Hose Port

3. Motor Unit

4. Dirt/water Tank

5. Castor Wheels

6. Blower Function Hose Port

7. Crevice Tool

8. Dusting Brush

9. Drainage Plug

10. Flex Hose

11. Carry Handle

12. Extension Tubes

13. Multi-Surface Vacuum

Nozzle (Dry Vacuuming Only)

14. Wet Pick-up Vacuum Nozzle

15. Power Cord Hook

16. Motor Unit Securing Clips

17. Accessories Storage

18. Power Cord with Plug

19. Suction Control Valve

20. Mico Particle Filter

13

8

14

12

7

19

20

2

9

5

17

18

1

6

11

4

15

3

16

10

ASSEMBLY INSTRUCTIONS:

Your Bennett Read Tough 35 needs very little assembly, please read and follow the below instructions carefully:

Note: you will need a Phillips screwdriver to complete the assembly

1. Remove unit from packaging

2. Remove attachments from their packaging

3. Some of the packaging poses a choking risk to small children.

Dispose of the packaging responsibly. Recycle if possible

4. Before using for the first time check that all attachments listed are included. If the unit is incomplete, return to the retailer immediately.

Take entire unit, packaging and proof of purchase to the store where your purchase was made

5. Remove the Motor Unit (3) from the Dirt Tank (4) by loosening the

Securing Clips (16). Push Securing Clips (16) outwards to release

6. Turn the Dirt Tank (4) upside down

5

7. Insert Castor Wheels (5) into the

Wheel base as shown

8. Insert all caster wheel assemblies (5) at the bottom of the Dirt Tank (4) into the holes provided, insert the screw and tighten with Phillips screwdriver. Take care not to over-tighten the screws as this may damage the thread.

9. Your Tough 35 is now ready to be set up for your desired application.

OPERATIONS

Only operate your Bennett Read Tough 35 in accordance with the instruction manual. Failure to follow these instructions will result in decreased cleaning performance and may invalidate your guarantee.

DRY VACUUMING:

Your Bennett Read Tough 35 Vacuum is perfect for vacuuming carpets, tiles, mattresses, upholstery, curtains and car upholstery.

Setting up your Bennett Read Tough 35 for dry vacuuming:

1. Remove the Motor Unit (3) from the Dirt Tank (4) by pushing the Locking Clips (16) outwards

2. Ensure that the Microparticle filter (20) is securely installed in place:

(A) (B)

6

3. Return the Motor Unit (3) to the Dirt Tank (4) and clip locks in place (16) by pushing inward

4. Insert the large end of the Flex Hose (10) into Vacuum Function Hose Port (2)

5. Attach the Extension Tubes (12) to the free end of the Flex Hose

6. Attach the Multi-Surface Vacuum Nozzle (13) to the free end of the Extension Wand

7. Plug the power cable into the wall socket

8. Switch on the unit using the Power Switch (1)

9. Vacuum in different directions across your surfaces to give you best results

After each cleaning session it is of utmost importance that:

• The dirt tank be emptied and thoroughly rinsed and dried before storing

• The Microparticle filter is checked and cleaned

This will ensure that the unit continues to deliver outstanding performance time & again

WET VACUUMING:

Your Bennett Read Tough 35 can also suck up liquids * in and around your home…

*Please note that the Bennett Read Tough 35 is NOT a carpet deep cleaner.

Carpet deep cleaning should be done with specialized deep cleaners.

Setting up your Bennett Read Tough 35 for wet vacuuming:

1. Remove the Motor Unit (3) from the Water/dirt Tank (4) by pushing the Locking Clips (16) outwards

2. Remove the Microparticle filter (20) (as explained in the Maintenance and Care section on the following page)

3. Return the Motor Unit (3) to the Dirt Tank (4) and clip locks in place (16) by pushing inward

4. Insert the large end of the Flex Hose (10) into Vacuum Function Hose Port (2)

5. Attach the Extension Tubes (12) to the free end of the Flex Hose

6. Attach the Wet Pick-up Vacuum Nozzle (14) to the free end of the Extension Wand

7. Plug the Power Cable into the wall socket

8. Switch on unit using the Power Switch (1)

9. Vacuum wet spill / liquid from surface

10. When you are done, follow the cleaning instructions as outlined below

*Do not use to pick up boiling hot, flammable or combustible liquids

Your Bennett Read Tough 35 is equipped with a float valve located at the bottom of the motor unit which will partially shut off the suction as soon as the tank reaches capacity. Immediately switch off the machine and empty the tank before continuing.

BLOWER FUNCTION:

Your Bennett Read Tough 35 has an additional function that allows you to blow away dirt and dust that collect on various surfaces and hard to reach areas.

Setting up your Bennett Read Tough 35 to use the blower function:

1. Remove the Motor Unit (3) from the Dirt Tank (4) by pushing the Locking Clips (16) outwards

2. Ensure that the Microparticle filter is securely installed in place

3. Replace the Motor Unit (3) and lock clips in place (16)

7

4. Insert the large end of the Flex Hose (10) into the Blower function hose port (6). Turn clockwise to lock in place

5. Attach the Extension tubes (12) to the free end of the Flex Hose (optional)

6. Plug the Power Cable into the wall socket

7. Switch on the unit using the Power Switch (1)

MAINTENANCE AND CARE

EMPTYING THE DIRT TANK:

1. Disconnect the Flex Hose (10) from the Motor Unit by turning anticlockwise and then pulling the hose outward

2. Take the unit to disposal area

3. Unclip and lift the Motor Unit (3) from the Dirt Tank and place on the ground

4. Lift the Dirt Tank and empty the contents into the disposal area

5. The Dirt Tank (4) is also equipped with a Drain Plug (9) to easily dispose of liquids

6. Rinse the Dirt Tank under running water and dry before storing

CLEANING THE FILTER:

Note: Your Tough 35 is equipped with a Thermal Cut-off Switch that is designed to protect the motor from overheating. Should the machine switch off whilst working, unplug and check the Microparticle filter. Clean as explained below. Your machine will be ready for use again as soon as it has cooled down. See the Troubleshooting Guide for more information.

It is necessary to clean the filter after EVERY USE / DAILY

• To remove the Microparticle filter, turn the Motor Unit (3) upside down

• Grasp the locking mechanism at the bottom of the Microparticle filter (20).

Twist anticlockwise and pull the filter outward to remove – see pictures below.

• Gently tap the filter on a solid surface, like the inside of a dust bin, to remove all visible dirt and dust. Use a brush to remove any large dirt particles or hair from the filter

TIP: You can also use compressed air to remove dust and dirt from the filter.

Wash the Microparticle filter weekly

• Wash the filter in warm water.

You may use a mild detergent

• Allow to dry completely before re-installing the filter

• Replacement Microparticle filters are available from major retail outlets

• Reassemble and store, ready to use!

IMPORTANT: NEVER USE THE MACHINE WITH A WET FILTER!

8

TROUBLESHOOTING

PROBLEM

Machine not switching on

POSSIBLE CAUSES

1. Power cord not firmly plugged in

or not switched on at wall socket

REMEDIES

1. Check electrical plug

1. Microparticle filter dirty or

clogged

1. Remove and clean

Microparticle filter as explained on page 6.

It is important to check and clean filter after every use

Weak suction power

2. Obstruction in Flex Hose, vacuum nozzle or extension pipes

2. Remove Flex Hose, nozzle and extension pipes as explained on page 7.

Clean and check for any obstructions

Visible dust escaping from the machine while vacuuming

1. Microparticle filter not installed

2. Microparticle filter dirty

1. Check Microparticle (20) filter, situated underneath the motor unit (3)

1. Clean Microparticle filter as explained on page 8

1. Filter dirty or clogged 1. Clean or replace the

Microparticle filter as explained in page 8

Machine switches off during operation

– Thermal Cut-off switch

2. Obstruction in flex hose/extension tubes

Check and clean flex hose/extension tubes

The machine will only switch on after it has cooled down sufficiently.

Permanent damage will be caused to your machine if you continue to use the machine without addressing the root cause of the overheating as explained above…

Other maintenance or service not included in the manual should be performed by an authorized Tevo service representative.

For any questions or concerns, contact customer care listed on page 10.

9

CONSUMER GUARANTEE

The Bennett Read Tough 35 has a one year product guarantee from Tevo (Pty)

Ltd. In the event of the unit malfunctioning, Tevo will replace or repair, at

Tevo’s option, any faulty component, free of charge from the date of purchase by the original purchaser for one year. This guarantee does not apply to routine maintenance components such as filters and brushes. Damage or malfunction caused by negligence, abuse, unauthorized repair, or use not in accordance with the User Guide is not covered. Tevo is not liable for incidental or consequential damages of any nature associated with the use of this product. Tevo’s liability will not exceed the purchase price of this product.

Guarantee and Service enquiries can be made by contacting:

Tevo (Pty) Ltd

Gauteng 086 111 8386

Durban (031) 570 5900

Cape Town (021) 380 0038/9

Customer Service Help Line 0861 77 88 88 www.tevo.co.za

TECHNICAL SPECIFICATIONS:

Nominal voltage: 220-240 V AC Nominal frequency:

50/60 Hz Power Output : 1200 W (nom)

Dirt Tank Capacity : 35 Litres

10

35

COMMERCIAL GRADE WET-DRY-BLOW VACUUMING SYSTEM

Brought to you by:

0861 77 88 88 www.tevo.co.za | [email protected]