Advertisement
Advertisement
MASON Wooden Swing Set Model: 36114 •• •• •• •• Owner's Manual Frequently Asked Questions Assembly Instructions Warranty Information Manufacturer: Backyard Discovery 3001 North Rouse Pittsburg, KS 66762 1-800-856-4445 Register your new swing set on-line @ www.swingsetsonline.com (you will also find any updates on assembly instructions and information to order replacement parts) Features the fastening system. Save this assembly manual for future reference in the event that you need to order replacement parts. INS-36114-A-MASON PC-ENG 10/2/13 Made in China STOP PARE Missing A Part? CALL US BEFORE GOING BACK TO THE STORE! The store where you made your purchase does not stock parts for this item. If you have assembly questions or if you need parts, whether they are missing or damaged Call Toll-Free Help Line or visit www.swingsetsonline.com ¡LLÁMENOS ANTES DE REGRESAR A LA TIENDA! La tienda donde realizó la compra no almacena piezas de este producto. Si tiene preguntas sobre el ensamblaje o si necesita piezas debido a que faltan o están dañadas llame gratis a la línea de ayuda 1-800-856-4445 PLEASE READ THIS BEFORE STARTING ASSEMBLY POR FAVOR LEA ESTAS INSTRUCCIONES ANTES DE COMENZAR EL ENSAMBLAJE • • • • • • • • • • • READ THE ASSEMBLY MANUAL COMPLETELY, PAYING SPECIAL ATTENTION TO THE IMPORTANT TIPS AND SAFETY INFORMATION. AFTER YOU HAVE READ THE ASSEMBLY MANUAL, YOU WILL BE ABLE TO DECIDE IF YOU NEED PROFESSIONAL HELP TO COMPLETE THE ASSEMBLY OF THE STRUCTURE. SEPARATE AND IDENTIFY ALL PARTS TO MAKE SURE THAT YOU HAVE ALL OF THE PARTS LISTED. IF YOU CAN’T FIND ALL OF THE PARTS, CHECK THE PACKING MATERIAL. SMALL PARTS MAY HAVE FALLEN INTO IT DURING SHIPMENT. IF YOU HAVE PROBLEMS WITH THE ASSEMBLY OR IF ANY PART IS MISSING OR DAMAGED, PLEASE CALL THE HELP LINE 1-800-856-4445 OR VISIT www.swingsetsonline.com LEA EL MANUAL DE ENSAMBLAJE COMPLETAMENTE, PRESTANDO ESPECIAL ATENCIÓN A LOS CONSEJOS ÚTILES IMPORTANTES Y A LA INFORMACIÓN SOBRE SEGURIDAD. DESPUÉS DE QUE HAYA LEÍDO EL MANUAL DE ENSAMBLAJE, PODRÁ DECIDIR SI NECESITA AYUDA PROFESIONAL PARA EFECTUAR EL ENSAMBLAJE DE LA ESTRUCTURA. SEPARE E IDENTIFIQUE TODAS LAS PIEZAS PARA COMPROBAR QUE DISPONE DE TODAS LAS PARTES INDICADAS. SI NO PUEDE ENCONTRAR TODAS LAS PIEZAS, REVISE EL MATERIAL DE EMPAQUE. ES POSIBLE QUE ALGUNAS PIEZAS PEQUEÑAS PUEDAN HABERSE CAÍDO ALLÍ DURANTE EL ENVÍO. MANTÉNGASE ALEJADO DE LOS NIÑOS MENORES A LA EDAD RECOMENDADA. SI TIENE PROBLEMAS CON EL ENSAMBLAJE O SI ALGUNA PIEZA FALTA O ESTÁ DAÑADA, LLAME A LA LÍNEA DE AYUDA AL 1-800-856-4445 O VISITE www.swingsetsonline.com PLEASE HAVE THE FOLLOWING INFORMATION WHEN YOU MAKE YOUR CALL: 1 – MODEL NUMBER OF THE PRODUCT LOCATED ON THE FRONT OF THE ASSEMBLY MANUAL 2 – DESRIPTION OF THE PART FROM THE PARTS LIST POR FAVOR TENGA VISIBLE LA SIGUIENTE INFORMACIÓN CUANDO LLAME: 1 - NÚMERO DE MODELO DEL PRODUCTO QUE SE ENCUENTRA UBICADO AL FRENTE DEL MANUAL DE ENSAMBLAJE 2 - DESCRIPCIÓN DE LA PIEZA QUE SE ENCUENTRA EN LA LISTA DE PIEZAS Owner’s Manual Play Set Dear Customer: Please read entire booklet completely before beginning the assembly process. Equipment is recommended for use by children 3 to 10 years of age. Structures are not intended for public use. The Company does not warranty any of its residential structures subjected to commercial use such as: Daycare, Preschool, Nursery School, Recreational Park, or any similar Commercial Application. WARNING: This Symbol points out important safety instructions which, if not followed, could endanger the personal safety of yourself and your children and/or damage your property. You MUST read and follow all instructions in this manual before attempting to use this playcenter. WARNING: Children must NOT use this playcenter until unit has been completely assembled and inspected by an adult to insure set has been properly installed and anchored. Please follow all recommendations below. Failure to do so may result in the warranty being void and/or safety violations that could result in serious injury. This manual contains helpful information concerning Assembly Preparation, Installation Procedure, and Required Maintenance. Always keep the safety of your children in mind as your play structure is being built and as your children play on the set. Before your children play on the set please review the Operation Instructions with them to help ensure their safety. PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. KEEP THEM IN A SAFE PLACE WHERE YOU CAN REFER TO THEM AS NEEDED. IN ORDER TO PROVIDE YOU WITH THE MOST EFFICIENT SERVICE, IT IS REQUIRED THAT YOU PROVIDE US WITH THE PART NUMBERS WHEN ORDERING PARTS. For Your Records: Please take time and fill out the information below. This information will be needed for warranty issues. Where Purchased: ____________________ Date of Purchase: ____________________ Installation Date: _____________________ Installed by: _________________________ Tracking Number: ____________________ Staple Receipt Here Tracking Number Reference Label Tracking ID number on the carton and back of the ID plate are included for tracking purposes associated with warranty claims. Rev12/13/12 Owner’s Manual Play Set Please refer to the Assembly section of the Assembly Manual for Maximum Fall Height. Positioning Your Playcenter 1. The Playcenter is designed to be installed on a level surface by an Adult with an Adult helper. Place in a flat area of your yard to minimize ground preparation. 2. Choose a level location for the equipment. This can reduce the likelihood of the play set tipping over and loose-fill surfacing material washing away during heavy rains. 3. Place the equipment not less than 6 ft (1.8 m) from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires. 4. Provide enough room so that the children can use the equipment safely. For example, for structures with multiple play activities, a slide should not exit in front of a swing. 5. It is a good idea to place your Playcenter in an area that is convenient for adults to watch children at play. 6. Create a site free of obstacles that could cause injuries – such as low overhanging tree branches, overhead wires, tree stumps and/or roots, large rocks, bricks and concrete. Additional suggestions in the Suggested Playground Surfacing Section. 7. Do not build your playset on top of surfacing material. 8. Locate bare metal platforms and slides out of direct sunlight to reduce the likelihood of serious burns. A slide that faces north will receive the least direct sunlight. 9. Separate active and quiet activities from each other. For example, locate sandboxes away from swings or use a guardrail or barrier to separate the sandbox from the movement of the swings. Suggested Playground Surfacing Do not install home playground equipment over concrete, asphalt, packed earth, grass, carpet, or any other hard surface. A fall onto a hard surface can result in serious injury to the equipment user. Do not install loose fill surfacing over hard surfaces such as concrete or asphalt. Shredded bark mulch, wood chips, fine sand and fine gravel, are added as shock absorbing materials after assembly. If used properly these materials can absorb some of the impact of a child’s fall. All surface material should extend a minimum of 6 feet in all directions around the play area. Do not apply playground surfacing until after the unit is completely constructed. Playset should not be built on top of surfacing. Use containment, such as digging out around the perimeter and/or lining the perimeter with landscape edging. Installations of rubber tiles or poured-in-place surfaces (other than loose-fill materials) generally require a professional and are not “do-it-yourself” projects. Shall use Playground Surfacing Materials (other than loose-fill material) which comply with the safety standard ASTM F1292 Standard Specification of Impact Attenuation of Surfacing Materials within the Use Zone of Playground Equipment. Rev12/13/12 Owner’s Manual Play Set The following chart explains the fall height in feet from which a life threatening head injury would not be expected Critical Heights in feet (m) of Tested Materials Material Uncompressed Depth Compressed Depth Wood Chips Double-Shredded bark mulch Engineered Wood Fibers Fine Sand Coarse Sand Fine Gravel Medium Gravel 6" (152mm) 7' (2.13m) 6' (1.83m) 6' (1.83m) 5' (1.52m) 5' (1.52m) 5' (1.52m) 5' (1.52m) 9" (228mm) 10' (3.05m) 10' (3.05m) 7' (2.13m) 5' (1.52m) 5' (1.52m) 7' (2.13m) 5' (1.52m) 12" (304mm) 11' (3.35m) 11' (3.35m) >12' (3.66m) 9' (2.74m) 6' (1.83m) 10' (3.05m) 6' (1.83m) to 9" (228mm) 10' (3.05m) 7' (2.13m) 6' (1.83m) 5' (1.52m) 4' (1.22m) 6' (1.83m) 5' (1.52m) Shredded Tires* 10-12' (3.0-3.6m) N/A N/A N/A *This data is from tests conducted by independent testing laboratories on a 6-inch depth of uncompressed shredded tire samples produced by four manufacturers. The tests reported critical heights, which varied from 10 feet to greater than 12 feet. It is recommended that persons seeking to install shredded tires as a protective surface request test data from the supplier showing the critical height of the material when it was tested in accordance with ASTM F1292. Operating Instructions: NOTE: Your children’s safety is our #1 concern. Observing the following statements and warnings reduces the likelihood of serious or fatal injury. Please review these safety rules regularly with your children. 1. This Playcenter is designed for specific number of occupants whose combined weight should not exceed a designated weight on the elevated floor or the swing area, the total Unit capacity is outlined in the Basic Setup Dimensions section of instruction manual. The maximum fall height and recommended play area is also available in the Basic Setup Dimensions section of the manual for the specific unit. 2. On-site adult supervision is required. 3. Instruct children not to walk close to, in front of, behind, or between moving swings or other moving playground equipment. 4. Instruct children to sit in and never stand on swings 5. Instruct children not to twist the chains and ropes and not to loop them over the top support bar, since this may reduce the strength of the chain or rope. 6. Instruct children not to jump from swings or other playground equipment in motion. 7. Instruct children to not to push empty seats. The seat may hit them and cause serious injury. 8. Instruct and teach children to sit in the center of the swings with their full weight on the seats. 9. Instruct children not to use the equipment in a manner other than intended. 10. Instruct children to always go down slides feet first. Never slide head first. 11. Instruct children to look before they slide to make sure no one is at the bottom. 12. Instruct children to never run up a slide, as this increases their chances of falling. 13. The parents should dress children appropriately. (Examples would include the use of wellfitting shoes and the avoidance of ponchos, scarfs, and other loose-fitting clothing that is potentially hazardous while using equipment). 14. Instruct children not to climb when the equipment is wet. 15. Instruct children to never jump from a fort deck. They should always use the ladder, ramp or slide. 16. Instruct children to never crawl or walk across the top of monkey bars. 17. Instruct children to never crawl on top of a fort roof. Rev12/13/12 Owner’s Manual Play Set 18. Verify that any suspended climbing ropes, chain, or cable are secured at both ends and that they cannot be looped back on it. 19. Instruct children not to attach items to the playground equipment that are not specifically designed for use with the equipment, such as, but not limited to, jump ropes, clothesline, pet leashes, cables and chain as they may cause a strangulation hazard. 20. Instruct children to never wrap their legs around swing chain. 21. Instruct children to never slide down the swing chain. 22. Instruct children to remove their bike or other sports helmet before playing on playground equipment. Maintenance Instructions: At the beginning of each play season: • Tighten all hardware. • Lubricate all metallic moving parts per manufacturer’s instructions. • Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose, cracked, or missing. • Check all moving parts including swing seats, ropes, cables, and chains for wear, rust, or other deterioration. Replace as needed. • Check metal parts for rust. If found, sand and repaint using a non Lead-based paint meeting the requirements of 16 CFR 1303. • Check all wood members for deterioration and splinters. Sand down splinters and replace deteriorating wood members. • Reinstall any plastic parts, such as swing seats or any other items that were removed for the cold season. • Rake and check depth of loose fill protective surfacing materials to prevent compaction and to maintain appropriate depth. Replace as necessary. Twice a month during play season: • Tighten all hardware. • Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose, cracked, or missing. • Rake and check depth of loose fill protective surfacing materials to prevent compaction and to maintain appropriate depth. Replace as necessary. • Once a month during play season. • Lubricate all metallic moving parts per manufacturer’s instructions. • Check all moving parts including swing seats, ropes, cables, and chains for wear, rust, or other deterioration. Replace as needed. At the end of each play season or when the temperature drops below 32° F: • Remove plastic swing seats and other items as specified by the manufacturer and take indoors or do not use. • Rake and check depth of loose fill protective surfacing materials to prevent compaction and to maintain appropriate depth. Replace as necessary. Owners shall be responsible for maintaining the legibility of the warning labels. Rev12/13/12 Owner’s Manual Play Set Additional Maintenance: • Check the swing beam and hardware every two weeks due to wood expansion and contraction. It is particularly important that this procedure be followed at the beginning of each season. • Inspect wood parts monthly. The grain of the wood sometimes will lift in the dry season causing splinters to appear. Light sand may be necessary to maintain a safe playing environment. Treat your playset with stain regularly, to help prevent severe checking/splitting and other weather damage. • A waterbourne transparent stain has been applied to your playset. This is done for color only. Once or twice a year, depending on your climate conditions, you must apply some type of protection (sealant) to the wood of your unit. Prior to the application of sealant, lightly sand any “rough” spots on your playset. Please note this is a requirement of your warranty. • Assembling and maintaining the playset on a level location is very important. As your children play, your playset will slowly dig its way into the soil, and it is very important that it settles evenly. Make sure the playset is level and true one each year or at the beginning of each play season. Disposal Instructions: When the Playcenter use is no longer desired, it should be disassembled and disposed of in such a way that no unreasonable hazards will exist at the time the unit is discarded. Third Party Assembly: Customer may, in their sole discretion, elect to use a third party person or service to assemble this product. Backyard Discovery assumes no responsibility or liability for any charge incurred by the Customer for any assembly services’. Please see our warranty for more information about damaged and missing part replacement coverage. Backyard Discovery will not reimburse Customer for the price of parts purchased. Rev12/13/12 Owner’s Manual Play Set APPENDIX A Information on Playground Surfacing Materials: The following information is from the United States Consumer Product Safety Commission’s Information Sheet for playground surfacing material; also see the following website for additional information: www.cpsc.gov/cpscpub/pubs/323.html. X3. SECTION 4 OF THE CONSUMER PRODUCT SAFETY COMMISSION’S OUTDOOR HOME PLAYGROUND SAFETY HANDBOOK9 X3.1 Select Protective Surfacing—One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with ASTM Specification F 1292. There are different types of surfacing to choose from; whichever product you select, follow these guidelines: X3.1.1 Loose-Fill Materials: X3.1.1.1 Maintain a minimum depth of 9 inches of loose-fill materials such as wood mulch/chips, engineered wood fiber (EWF), or shredded/recycled rubber mulch for equipment up to 8 feet high; and 9 inches of sand or pea gravel for equipment up to 5 feet high. NOTE: An initial fill level of 12 inches will compress to about a 9-inch depth of surfacing overtime. The surfacing will also compact, displace, and settle, and should be periodically refilled to maintain at least a 9-inch depth. X3.1.2 Use a minimum of 6 inches of protective surfacing for play equipment less than 4 feet in height. If maintained properly, this should be adequate. (At depths less than 6 inches, the protective material is too easily displaced or compacted.) NOTE: Do not install home playground equipment over concrete, asphalt, or any other hard surface. A fall onto a hard surface can result in serious injury to the equipment user. Grass and dirt are not considered protective surfacing because wear and environmental factors can reduce their shock absorbing effectiveness. Carpeting and thin mats are generally not adequate protective surfacing. Ground level equipment such as a sandbox, activity wall, playhouse or other equipment that has no elevated play surface – does not need any protective surfacing. X3.1.3 Use containment, such as digging out around the perimeter and/or lining the perimeter with landscape edging. Don’t forget to account for water drainage. X3.1.3.1 Check and maintain the depth of the loose-fill surfacing material. To maintain the right amount of loosefill materials, mark the correct level on play equipment support posts. That way you can easily see when to replenish and/or redistribute the surfacing. X3.1.3.2 Do not install loose-fill surfacing over hard surfaces such as concrete or asphalt. X3.1.4 Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles — You may be interested in using surfacing other than loose-fill materials – like rubber tiles or poured-in-place surfaces. X3.1.4.1 Installations of these surfaces generally require a professional and are not “do-it-yourself” projects. X3.1.4.2 Review surface specification before purchasing this type of surfacing. Ask the installer/manufacturer for a report showing that the product has been tested to the following safety standard: ASTM F 1292 Standard Specification for Impact Attenuation of Surfacing Materials within the Use Zone of Playground Equipment. This report should show the specific height for which the surface is intended to protect against serious head injury. This height should be equal to or greater than the fall height – vertical distance between a designated play surface (elevated surface for standing, sitting, or climbing) and the protective surfacing below – of your play equipment. X3.1.4.3 Check the protective surfacing frequently for wear. X3.1.5 Placement — Proper placement and maintenance of protective surfacing is essential. Be sure to: X3.1.5.1 Extend surfacing at least 6 feet from the equipment in all directions. X3.1.5.2 For to-fro swings, extend protective surfacing in front of and behind the swing to a distance equal to twice the height of the top bar from which the swing is suspended. 9 This information has been extracted from the CPSC publications “Playground Surfacing — Technical Information Guide” and “Handbook for Public Playground Safety.” Copies of these reports can be obtained by sending a postcard to the: Office of Public Affairs, U.S. Consumer Product Safety Commission, Washington, D.C., 20207 or call the toll-free hotline: 1-800-638-2772. Rev12/13/12 Owner’s Manual Play Set The American Society for Testing and Materials takes no position respecting the validity of any parent right asserted in connection with any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any such parent rights, and the risk of infringement of such rights, are entirely their own responsibility. The standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and if not revised, either approved or withdrawn. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards. 100 Barr Harbor Drive, West Conshohocken, PA 19428. Rev12/13/12 Play Set Assembly Manual FAQs: 1. Does the area for the playset need to be level? Yes. Backyard Discovery recommends the playset be positioned on a flat level area for maximum safety and durability. The stakes provided should be used to secure it firmly to the ground. 2. What size area is recommended for the playset? Backyard Discovery recommends at least a 6’ (six foot) perimeter around and above the playset for maximum safety. 3. What age range is appropriate for the playsets? Backyard Discovery playsets are recommended for children ages 3 – 10 years. 4. Is the wood treated with chemicals? Backyard Discovery uses 100% Chinese Cedar wood which is naturally bug resistant, decay and rot resistant. To help ensure your child’s safety, our wood is completely chemical free and we do not use pressure-treated wood. The stain we use is a top coat using a waterbased product that is for appearance only. 5. How often should the playset be stained? Backyard Discovery recommends the playset be stained once each year. A water or oil based stain can be used at the customer’s discretion. 6. Why does it seem that my swing set is developing cracks? Wood is a natural material; no two pieces are exactly alike. Each piece has its own characteristics and personality and reacts differently to climate changes. When any wood product is exposed to the elements, it develops “wood checks”. A check is the radial separation of the wood fibers running with the grain of the wood. These are caused by the varying temperature and moisture conditions. A check is not a crack – it does not affect the strength or durability of the wood or structural integrity of the play set. 7. Do Backyard Discovery playsets come with a warranty? Yes. All Backyard Discovery products carry a 1-year replacement warranty on all parts for manufacturer’s defect. Our wood carries a 5 year warranty on rot and decay as well. Please see warranty details for more information. 8. What is the best way to get started assembling the playset? Backyard Discovery recommends taking all the parts out of the boxes and arranging them by part number before you begin any assembly. This will not only allow faster assembly, but will also identify any parts that may be missing or damaged so they can be replaced before assembly. If parts are missing or need replacement, go to www.swingsetsonline.com/support.aspx and follow the prompts to order them. Next, read the assembly manual and get the tools ready for the job as recommended in the manual. If the assembly manual is lost or misplaced a new one can be printed from Backyard Discovery’s website: www.swingsetsonline.com. 9. The playset seems to rock or sway too much. What’s wrong? Rocking is caused by uneven ground or obstructions such as rocks, roots, etc. under the ground rails. These should be removed and the ground underneath re-leveled to prevent rocking. Also ensure the playset is securely staked to the ground using the stakes provided. 10. The 2”x4” boards do not measure 2”x 4”. Why not? In the U.S. it is common practice to describe lumber dimensions using the rough cut sizes from the sawmill and not the finished dimensions. Retailers, home stores, etc. all use this accepted practice for describing lumber dimensions. However, Backyard Discovery playsets are designed and constructed using the actual dimensions so everything fits properly and remains so during the life of the playset. 11. The end beam is not straight up and down. Why not? This is normal. Backyard Discovery designs playsets this way to ensure the strongest structure possible. The slight angle adds strength and reduces rocking and twisting. 12. The S-hooks for the swings won’t close. What is wrong? Backyard Discovery recommends placing them on a hard surface such as concrete (don’t do this on anything that will dent such as metal or finished wood or glass which will break!). It will take quite a few strokes, but the hooks will close. For more information and frequently asked questions, please refer to our website at www.swingsetsonline.com. Basic Setup Dimensions Place the set on level ground, not less than 6 ft [2 m] from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires. 24'-7 1/2" [7.5] 12'-7 1/2" [3.8] 12'-7 1/2" [3.8] 24'-7 1/2" [7.5] 6'-0" [1.8] Safe Play Zone General Information: Your set has been designed and engineered for children only and for residential use only. A maximum of 150 lbs. per child is recommended for play activities designed for individual use. A maximum of 120 lbs. per child is recommended for play activities designed for multiple child use. A maximum of 8 children is recommended for this swing set. 6'-0" [1.8] Important Assembly Notes 6'- 3/4" [1.8] 9'-4" [2.8] Safe play height: 15'-4" [4.7 m] Maximum fall height: 6'-11/16" [1.8 m] 1) While assembling unit, take time before and after each phase to make sure fort is level. If fort is not level, assembly will be difficult and improper assembly may result. Extra care must be taken to insure the fort is square. 2) Tighten bolts securely, tighten nuts on bolts flush to the tube or member, and place caps over exposed bolts snug to the nut. 3) Pay close attention to the ITEMS NEEDED FOR EACH PHASE. They can be a valuable aid when sorting your wood and hardware. Assembly will be made easier if items are sorted by phase. 4) Pay close attention to make sure you are using the correct hardware in the correct phases. Using incorrect hardware may result in improper assembly. 5) Whenever a T-nut is used, follow these directions. Place T-nut in pre-drilled hole. Tap in with hammer. Place bolt with washers in the opposite side. Hand tighten to make sure the bolt is in the T-nut. DO NOT over tighten. 6) Read the steps of each phase thoroughly. The written steps may include important information not shown in the illustrations. Tools Required for Installation: (These are the tools that are generally required for assembly of our outdoor products. These tools are not included with the outdoor product purchase.) (Square) (Level 24") (Tape Measure) (Open End Wrenches 1/2") (3/8" Drive Ratchet, 1/2" STD Sockets 1/2" Deep Sockets) (Phillips Screw Driver) (Claw Hammer) (Rubber Mallet - Optional) (Cordless Drill or Electric Drill) (An Adult w/ an Adult Helper) (Drill Attachments: Phillips Head & Socket Driver) (Ladder) Parts Identification Wood Components (NOT TO SCALE) (4) D1 - PICNIC TABLE SUPPORT BRACE - W101117 1 3/8"x5 1/4"x17" (36x134x432) (1) E1 - UPRIGHT - W101084 1 3/8"x3 3/8"x89 1/2" (36x86x2274) (1) E2 - UPRIGHT - W101104 1 3/8"x3 3/8"x89 1/2" (36x86x2274) (1) E3 - UPRIGHT - W101106 1 3/8"x3 3/8"x89 1/2" (36x86x2274) (1) E4 - UPRIGHT - W101107 1 3/8"x3 3/8"x89 1/2" (36x86x2274) (2) (1) E5 - UPRIGHT - W101085 1 3/8"x3 3/8"x66" (36x86x1676) (1) E6 - UPRIGHT - W101120 1 3/8"x3 3/8"x66" (36x86x1676) E77 - ANGLE BRACE - W100991 1 3/8"x3 3/8"x74 3/8" (36x86x1890) (1) G1 - WALL RAIL - W101111 1"x5 1/4"x43" (24x134x1092) (1) G2 - WALL RAIL - W101122 1"x5 1/4"x43" (24x134x1092) (1) (1) G3 - CABIN ARCH - W101096 1"x5 1/4"x41 1/8" (24x134x1044) G4 - SWING BEAM MOUNT - W101105 1"x5 1/4"x41 1/8" (24x134x1044) (1) G5 - WALL RAIL - W101112 1"x5 1/4"x41 1/8" (24x134x1044) Parts Identification Wood Components (NOT TO SCALE) (1) H74 - LEFT UPRIGHT - W100608 1"x3 3/8"x50 3/4" (24x86x1290) (1) (1) H1 - FLOOR JOIST - W102377 1"x3 3/8"x41 1/8" (24x86x1044) H75 - RIGHT UPRIGHT - W100609 1"x3 3/8"x50 3/4" (24x86x1290) (4) H76 - LADDER RUNG - W100611 1"x3 3/8"x18 1/8" (24x86x460) (1) H79 - END SUPPORT - W100992 1"x3 1/2"x42" (24x86x1072) (1) H80 - GROUND BOARD - W100990 1"x3 3/8"x87 3/8" (24x86x2218) (4) J1 - FLOOR SUPPORT - W101037 1"x2 3/8"x3" (24x60x76) (1) K1 - GROUND BOARD - W101090 5/8"x5 1/4"x74 1/4" (16x134x1886) (2) K2 - GROUND BOARD - W101091 5/8"x5 1/4"x67 5/8" (16x134x1718) K3 - DOUBLE ARCH RAIL - W101092 5/8"x5 1/4"x43" (16x134x1092) (1) (3) (2) K4 - WALL RAIL - W101093 5/8"x5 1/4"x43" (16x134x1092) K6 - WALL RAIL - W101095 5/8"x5 1/4"x41 1/8" (16x134x1044) Parts Identification Wood Components (NOT TO SCALE) K91 - ROOF SLAT - W100917 3/8"x3 3/8"x50" (11x86x1270) (24) L1 - OUTER FLOOR BOARD - W101110 5/8"x4 3/8"x40 1/8" (16x112x1018) (2) (4) L2 - OUTER WALL SLAT - W101100 5/8"x4 3/8"x39" (16x112x992) (4) L3 - RAFTER - W100913 5/8"x4 3/8"x38 1/4" (16x112x972) (1) M2 - WALL RAIL - W101097 5/8"x3 3/8"x67 5/8" (16x86x1718) (1) M3 - ANGLE BRACE - W101121 5/8"x3 3/8"x52 1/2" (16x86x1335) (10) M4 - FLOOR BOARD - W101109 5/8"x3 3/8"x44 7/8" (16x86x1140) (1) M5 - TARP SUPPORT - W101125 5/8"x3 3/8"x44 1/4" (16x86x1124) (1) (6) M7 - WALL RAIL - W101099 5/8"x3 3/8"x43" (16x86x1092) M10 - PICNIC TABLE BOARD - W101118 5/8"x3 3/8"x41 5/8" (16x86x1056) (2) (2) M11 - WALL RAIL - W101116 5/8"x3 3/8"x41 1/8" (16x86x1044) M12 - TARP BRACE - W101089 5/8"x3 3/8"x41" (16x86x1042) Parts Identification Wood Components (NOT TO SCALE) (16) (6) (1) M13 - WALL SLAT - W101101 5/8"x3 3/8"x39" (16x86x992) (16) M14 - WALL SLAT - W101115 5/8"x3 3/8"x25 5/8" (16x86x652) (8) M15 - WALL SLAT - W101126 5/8"x3 3/8"x23 1/4" (16x86x591) M16 - CENTER WALL SLAT - W101102 5/8"x3 3/8"x20 3/8" (16x86x518) (2) M18 - DOOR BOARD - W100918 5/8"x3 3/8"x39 1/2" (16x86x1002) (1) M20 - DOOR BOARD - W100920 5/8"x3"x38 1/4" (16x76x972) (1) M21 - DOOR BOARD - W100919 5/8"x3"x38 1/4" (16x76x972) (2) M22 - DOOR BOARD - W100921 5/8"x3 3/8"x25" (16x86x634) (2) M23 - DOOR BOARD - W100922 5/8"x3 3/8"x6 1/4" (16x86x160) M40 - STRIKE PLATE BLOCK - W101134 5/8"x3 3/8"x1" (16x86x24) (1) (1) M73 - REAR SUPPORT - W100610 5/8"x3 3/8"x19 1/4" (16x86x488) M77 - SLIDE BRACE - W100544 5/8"x3 3/8"x17 1/4" (16x86x438) Parts Identification Wood Components (NOT TO SCALE) M78 - CENTER SLIDE BRACE - W100545 5/8"x3 3/8"x17 1/4" (16x86x438) (2) (1) N1 - CENTER RAIL - W101113 5/8"x2 3/8"x25 5/8" (16x60x652) (2) N2 - TIE SLAT - W101103 5/8"x2 3/8"x14 5/8" (16x60x372) (2) (2) N4 - HORIZONTAL SUNBURST - W100914 5/8"x2 3/8"x32 7/8" (16x60x835) N5 - VERTICAL SUNBURST - W100915 5/8"x2 3/8"x12 7/8" (16x60x328) (2) (4) N6 - ANGLED SUNBURST - W100916 5/8"x2 3/8"x7 7/8" (16x60x200) (3) (1) O1 - DOOR SUPPORT - W100923 5/8"x1 3/8"x19" (16x34x482) O2 - DOOR MOUNTING RAIL - W101133 5/8"x1 3/8"x39" (16x34x992) (1) (1) N3 - TIE SLAT - W101119 5/8"x2 3/8"x8" (16x60x204) SB74 - SWING BEAM - W102304 2"x5 1/4"x89 1/2" (50x134x2274) W71 - SWING BEAM SUPPORT - W102305 2"x3 3/8"x46 1/8" (50x86x1170) Parts Identification Hardware (7) CM - BOLT WH 5/16x1/2 - H100115 (2) AN - BOLT HEX 5/16x2-3/4 - H100047 (10) CX - SCREW PPH 4x5/8 -H100127 (1) F - BOLT WH 5/16x1 - H100008 (4) AJ - BOLT HEX 5/16x1 1/4 - H100042 (32) H - BOLT WH 5/16x1 1/2 - H100010 (2) AY - BOLT PTH 1/4x1 - H100061 (9) BG - T-NUT 5/16 - H100074 (6) J - BOLT WH 5/16x1 3/4 - H100011 (2) BE - T-NUT 1/4 - H100072 (96) AC - WASHER LOCK EXT 8x19 - H100030 (13) K - BOLT WH 5/16x2 - H100012 (9) CY - SCREW PWH 8x5/8 -H100128 (4) L - BOLT WH 5/16x2 1/4 - H100013 (73) AD - WASHER LOCK EXT 12x19 - H100031 (22) BC - SCREW PWH 8x3/4 -H100070 (9) M - BOLT WH 5/16x2 1/2 - H100014 (2) C - NUT BARREL WH 5/16x1 1/2 - H100006 (2) P - BOLT WH 5/16x3 - H100016 (62) D - NUT BARREL WH 5/16x7/8 - H100005 (1) V - BOLT WH 5/16x5 - H100022 (8) B - NUT BARREL WH 5/16x5/8 - H100004 (4) AE - BOLT WH 5/16x5 3/4 - H100032 Parts Identification (86) BP - SCREW PFH 8x1 1/2 - H100086 (9) BS - SCREW PFH 8x1 3/4 - H100089 (33) CK - SCREW PFH 8x2 - H100111 (26) BW - SCREW PFH 8x3 - H100092 (32) Z - LAG SCREW WH 5/16x2 - H100027 (4) CB - WASHER SAFETY 17x30 -H100103 (4) CG - WASHER LOCK INT 8x15 - H100108 (1) - T-40 TORX WRENCH - A100041 (52) BQ - SCREW PFH 8x1 1/4 - H100087 (4) CE - WASHER FLAT 9x18 - H100106 - SWING HANGER QUICK LINK (4) -BY H100097 (273) BR - SCREW PFH 8x1 1/8 - H100088 (4) BZ - SWING HANGER QUICK LINK - H100099 Hardware - LAG SCREW WH 5/16x2 1/2 (2) -AA H100028 (13) BL - SCREW TAPPING 14x3/4 - H100083 - SCREW TAPPING 14x1-1/2 (2) CH -H100109 (22) CD - WASHER FLAT 8x27 -H100105 (1) - T-40 TORX BIT - A100042 (16) CJ - NUT LOCK 5/16 -H100110 (4) BX - WASHER SPLIT 5/16 - H100095 Parts Identification Accessories (NOT TO SCALE) - WINDOW FRAME 216x267 BYD (1) GK GREEN -A100146 - TUBING CAP GLIDER SUPPORT - WINDOW FRAME GREEN (4) EY (2) EB -A100067 343x444.5 -A100044 (1) JZ - PICNIC TARP - A100143 (1) DL - GLIDER SEAT YELLOW - A100023 (4) EX - GLIDER BUSHING BYD GREEN - A100066 (2) DK - GLIDER ARM BYD GREEN - A100022 (2) EW - GLIDER SUPPORT BYD GREEN - A100065 (2) FR - LEAF HINGE - A100093 (2) QZ - TRIANGLE PLATE 100° 5 HOLE - A100294 (2) GD - L BRACKET 66x66x127 -A100140 (1) HZ - KNOB - A100071 (3) GH - SCREW -A100145 SCREW GF - MAGNETIC CATCH KIT -A100145 (1) MAG (1) GJ - STRIKE PLATE -A100145 STRIKE (8) FA - QUICK LINK -A100069 Parts Identification Accessories (NOT TO SCALE) (1) EK - SLIDE RAIL 8' GREEN RIGHT - A100054 (6) KD - PLASTIC GROUND STAKE BROWN - A100179 (1) EL - SLIDE RAIL 8' GREEN LEFT - A100055 - TRIANGLE PLATE 90 5 HOLE BYD (2) DE GREEN -A100011 (1) EM - SLIDE BED 8' YELLOW - A100056 - HAND GRIP YELLOW PLASTIC (2) EA -A100043 (2) FB - SWING SEAT YELLOW - A100070 - BYD ID TAG (LARGE) 2011 WITH (2) HC AGES -A100164 (1) EJ - L BRACKET 54x67 -A100053 (4) DG - CHAIN GREEN 38.5" - A100015 (1) TELESCOPE KIT 1992 (4) EZ - CHAIN GREEN 51.25" - A100068 8 FOOT SLIDE ASSEMBLY PHASE 1 Phase Notes TOP ● DRILL 3 HOLES AT ONE END OF THE PLASTIC SLIDE BED USING A 5/16" DRILL BIT AND USING THE DIMENSIONS SHOWN BELOW. THIS END WILL BE THE TOP OF THE SLIDE. ● TAKE NOTE OF SLIDE BED SURFACE FINISH, THE DULL SIDE WILL BE TOWARDS THE GROUND. PLACE SLIDE BRACE CENTERED ON THE BOTTOM (DULL SIDE) AND 1/4" FROM THE EDGE. TRANSFER HOLES ON THE BOARD THROUGH THE SLIDE BED AS SHOWN BELOW. USE A 5/16" DRILL BIT. ● ATTACH SLIDE BRACE TO SLIDE USING HARDWARE SHOWN. BRIGHT SIDE QTY 1 3 3 3 1 TOP 13 5/8 8 5/8 3 5/8 DESCRIPTION SLIDE BRACE BOLT WH 5/16x1/2 NUT BARREL WH 5/16x5/8 WASHER LOCK EXT 12x19 SLIDE BED 8' YELLOW 1 BOTTOM SLIDE BED 8' YELLOW NUT BARREL WH 5/16x5/8 WASHER LOCK EXT 12x19 SLIDE BRACE BOLT WH 5/16x1/2 TIP: PREBENDING THE ENDS WILL EASE ASSEMBLY. REV 8/02/11 BRS 8 FOOT SLIDE ASSEMBLY PHASE 2 Phase Notes ● PLACE 1 SLIDE RAIL ON A FLAT SURFACE AND BEGIN INSERTING SLIDE BED AT THE BOTTOM OF THE SLIDE RAIL. PUT SLIDE SUPPORT BOTTOM INTO THE SUPPORT POCKET AT THE BOTTOM OF THE RAIL AND HAVE A HELPER BEND THE SLIDE BED TOWARDS THE TOP OF THE SLIDE AND INSERT THE BED INTO THE SLIDE CAVITY. MAKE SURE SLIDE BED IS COMPLETELY DOWN IN THE SLIDE CAVITY. ● PLACE THE OTHER SLIDE RAIL ON A FLAT SURFACE WITH THE SLIDE CAVITY UP. HAVE A HELPER HOLD THE TOP END OF SLIDE BED AND BEGIN INSERTING THE SLIDE BED AND SLIDE BRACES INTO THE CAVITY AND SUPPORT POCKETS STARTING AT THE BOTTOM OF SLIDE AND WORKING UP TO THE TOP. ● ONCE BED AND BRACES ARE COMPLETELY IN THE CAVITY AND IN THE SUPPORT POCKETS, SECURE USING 3" SCREWS AT EACH OF THE PILOT HOLE LOCATIONS AS SHOWN BELOW. SLIDE RAIL 8' GREEN RIGHT CENTER SLIDE BRACE SLIDE RAIL 8' GREEN LEFT QTY DESCRIPTION 2 24 1 1 CENTER SLIDE BRACE SCREW PFH 8x3 SLIDE RAIL 8' GREEN RIGHT SLIDE RAIL 8' GREEN LEFT SCREW PFH 8x3 TIP: A HELPER IS REQUIRED FOR THIS PHASE. 4 Ft Ladder Phase 1 & 2 Phase Notes • Assemble with hardware as shown. • Center rungs in rail grooves. QTY 1 DESCRIPTION LEFT UPRIGHT LABEL H74 4 8 LADDER RUNG SCREW PFH 8x2 H76 SCREW PFH 8x2 H74 H76 QTY 1 8 DESCRIPTION RIGHT UPRIGHT SCREW PFH 8x2 H75 SCREW PFH 8x2 LABEL H75 4 Ft Ladder Phase 3 Phase Notes • Assemble with hardware as shown. M73 SCREW PFH 8x2 QTY 1 4 DESCRIPTION REAR SUPPORT SCREW PFH 8x2 LABEL M73 (1) SB74 - SWING BEAM - W102304 2"x5 1/4"x89 1/2" (50x134x2274) (2) GD - L BRACKET 66x66x127 - A100140 (2) QZ - TRIANGLE PLATE 100° 5 HOLE - A100294 SWING BEAM ASSEMBLY STEP 1 (3) BOLT WH 5/16x1 3/4 ATTACH (2) QZ TRIANGLE PLATES TO SB74 SWING BEAM USING 1-3/4" BOLTS, LOCK WASHER AND 7/8" BARREL NUT. ATTACH (2) GD L BRACKETS TO SB74 SWING BEAM USING 2-3/4" HEX BOLTS, FLAT WASHERS AND 5/16" LOCK NUTS. (2) (2) BOLT HEX 5/16x2-3/4 NUT LOCK 5/16 (4) WASHER FLAT 8x27 NUT BARREL (3) WH 5/16x7/8 GD SB74 QZ (1) (2) W71 - SWING BEAM SUPPORT - W102305 2"x3 3/8"x46 1/8" (50x86x1170) (1) E77 - ANGLE BRACE - W100991 1 3/8"x3 3/8"x74 3/8" (36x86x1890) (1) H79 - END SUPPORT - W100992 1"x3 1/2"x42" (24x86x1072) H80 - GROUND BOARD - W100990 1"x3 3/8"x87 3/8" (24x86x2218) SWING BEAM ASSEMBLY STEP 2 (4) INSERT (2) 2-1/2" BOLTS, LOCK WASHERS AND 1-1/2" BARREL NUTS INTO TOP EDGE OF W71 SWING BEAM SUPPORT, AS SHOWN. THIS SAFE-T-FUSE HARDWARE MUST BE MOUNTED TO IMPROVE THE STRUCTURAL INTEGRITY OF THE SWING BEAM. ATTACH E77 ANGLE BRACES TO W71 SWING BEAM SUPPORT USING 4- 1/2" BOLTS, LOCK WASHERS AND 7/8" BARREL NUTS. ATTACH H79 END SUPPORT TO E77 ANGLE BRACES USING 2" BOLTS, LOCK WASHERS AND 7/8" BARREL NUTS. NOW ATTACH H79 END SUPPORT TO W71 SWING BEAM SUPPORT USING 2" LAG SCREWS AND LOCK WASHERS. BOLT WH 5/16x2 (2) (9) WASHER LOCK EXT 8x19 (7) WASHER LOCK EXT 12x19 BOLT WH 5/16x2 1/2 (2) (1) BOLT WH 5/16x4 1/2 LAG SCREW WH 5/16x2 NUT BARREL (5) WH 5/16x7/8 W71 ATTACH H80 GROUND BOARD TO E77 ANGLE BRACES USING 2" BOLTS, LOCK WASHERS AND 7/8" BARREL NUTS. E77 NUT BARREL (2)WH 5/16x1 1/2 H79 E77 H80 SWING BEAM ASSEMBLY (4) STEP 3 ATTACH (2) QZ TRIANGLE PLATES TO W71 SWING BEAM SUPPORT USING 1-3/4" BOLTS AND 7/8" BARREL NUTS (FIG. 1). INSERT SWING HANGER QUICK LINK AND SAFETY WASHER INTO HOLES IN THE EDGE OF SB74 SWING BEAM. SECURE SWING HANGER TO W71 SWING BEAM USING FLAT WASHERS AND 5/16" LOCK NUTS (FIG.2). ATTACH EW GLIDER SUPPORT TO SB74 USING 5-3/4" BOLTS, FLAT WASHERS, LOCK NUTS, AND 2-1/2" LAG SCREWS (FIG.3). (4) SWING HANGER QUICK LINK SWING (2) BOLT WH 5/16x1 3/4 HANGER QUICK LINK BOLT WH (2) 5/16x5 3/4 NUT BARREL (2) WH 5/16x7/8 LAG SCREW (2)WH 5/16x2 1/2 (4) WASHER SAFETY 17x30 (10) (10) QZ W71 FIG. 1 EW FIG. 3 FIG. 2 WASHER FLAT 8x27 NUT LOCK 5/16 (1) (1) E1 - UPRIGHT - W101084 1 3/8"x3 3/8"x89 1/2" (36x86x2274) K6 - WALL RAIL - W101095 5/8"x5 1/4"x41 1/8" (16x134x1044) (1) (1) G3 - CABIN ARCH - W101096 1"x5 1/4"x41 1/8" (24x134x1044) E2 - UPRIGHT - W101104 1 3/8"x3 3/8"x89 1/2" (36x86x2274) (1) K2 - GROUND BOARD - W101091 5/8"x5 1/4"x67 5/8" (16x134x1718) STEP 1 BOLT WH 5/16x1 1/2 (8 PLCS) (2) T-NUT 5/16 WASHER LOCK EXT 8x19 (12 PLCS) (2) BOLT WH 5/16x2 (8) BOLT WH 5/16x1 1/2 (2) BOLT WH 5/16x2 1/4 NUT BARREL (10) WH 5/16x7/8 K6 (12) WASHER LOCK EXT 8x19 (10) WASHER LOCK EXT 12x19 BOLT WH 5/16x2 (4 PLCS) E1 BOLT WH 5/16x2 1/4 (4 PLCS) G3 E2 K2 NOTE: HOLE ORIENTATION WASHER LOCK EXT 12x19 (10 PLCS) NUT BARREL WH 5/16x7/8 (10 PLCS) T-NUT 5/16 (2 PLCS) (1) (1) (1) E3 - UPRIGHT - W101106 1 3/8"x3 3/8"x89 1/2" (36x86x2274) (1) K1 - GROUND BOARD - W101090 5/8"x5 1/4"x74 1/4" (16x134x1886) K2 - GROUND BOARD - W101091 5/8"x5 1/4"x67 5/8" (16x134x1718) (1) (1) E4 - UPRIGHT - W101107 1 3/8"x3 3/8"x89 1/2" (36x86x2274) G4 - SWING BEAM MOUNT - W101105 1"x5 1/4"x41 1/8" (24x134x1044) K6 - WALL RAIL - W101095 5/8"x5 1/4"x41 1/8" (16x134x1044) (1) (1) G5 - WALL RAIL - W101112 1"x5 1/4"x41 1/8" (24x134x1044) M2 - WALL RAIL - W101097 5/8"x3 3/8"x67 5/8" (16x86x1718) STEP 2 T-NUT 5/16 (2 PLCS) (6) BOLT WH 5/16x1 1/2 (6) BOLT WH 5/16x2 1/4 NOTE: HOLE ORIENTATION (6) BOLT WH 5/16x2 1/4 (2 PLCS) BOLT WH 5/16x2 (2) BOLT WH 5/16x2 (2 PLCS) WASHER LOCK EXT 8x19 (2 PLCS) E3 E4 G4 NUT BARREL WH 5/16x7/8 (16 PLCS) BOLT WH 5/16x2 (4 PLCS) WASHER LOCK EXT 12x19 (16 PLCS) BOLT WH 5/16x1 1/2 (4 PLCS) K6 G5 BOLT WH 5/16x1 1/2 (2 PLCS) M2 K1 BOLT WH 5/16x2 1/4 (4 PLCS) K2 WASHER LOCK EXT 8x19 (18 PLCS) NUT BARREL (16) WH 5/16x7/8 T-NUT 5/16 (18) WASHER LOCK EXT 8x19 (16) WASHER LOCK EXT 12x19 (1) G2 - WALL RAIL - W101122 1"x5 1/4"x43" (24x134x1092) (1) K3 - DOUBLE ARCH RAIL - W101092 5/8"x5 1/4"x43" (16x134x1092) (1) K4 - WALL RAIL - W101093 5/8"x5 1/4"x43" (16x134x1092) STEP 3 K3 7/8" (12) LAG SCREW WH 5/16x2 (12) G2 WASHER LOCK EXT 8x19 (12 PLCS) LAG SCREW WH 5/16x2 (12 PLCS) K4 WASHER LOCK EXT 8x19 (1) G1 - WALL RAIL - W101111 1"x5 1/4"x43" (24x134x1092) (2) K4 - WALL RAIL - W101093 5/8"x5 1/4"x43" (16x134x1092) STEP 4 (12) K4 LAG SCREW WH 5/16x2 (12) WASHER LOCK EXT 8x19 G1 7/8" LAG SCREW WH 5/16x2 (12 PLCS) WASHER LOCK EXT 8x19 (12 PLCS) K4 (1) H1 - FLOOR JOIST - W102377 1"x3 3/8"x41 1/8" (24x86x1044) (4) J1 - FLOOR SUPPORT - W101037 1"x2 3/8"x3" (24x60x76) STEP 5 (8) SCREW PFH 8x1 3/4 (4) SCREW PFH 8x1 3/4 (8 PLCS) J1 SCREW PFH 8x2 J1 H1 J1 FLUSH J1 SCREW PFH 8x2 (4 PLCS) (2) L1 - OUTER FLOOR BOARD - W101110 5/8"x4 3/8"x40 1/8" (16x112x1018) (10) M4 - FLOOR BOARD - W101109 5/8"x3 3/8"x44 7/8" (16x86x1140) STEP 6 (68) L1 SCREW PFH 8x1 1/2 (68 PLCS) L1 M4 SCREW PFH 8x1 1/2 (1) M7 - WALL RAIL - W101099 5/8"x3 3/8"x43" (16x86x1092) (2) M11 - WALL RAIL - W101116 5/8"x3 3/8"x41 1/8" (16x86x1044) STEP 7 (4) BOLT WH 5/16x1 1/2 (2) LAG SCREW WH 5/16x2 NUT BARREL (4) WH 5/16x7/8 M11 M7 (6) WASHER LOCK EXT 8x19 (4) WASHER LOCK EXT 12x19 M11 LAG SCREW WH 5/16x2 (2 PLCS) WASHER LOCK EXT 8x19 (6 PLCS) BOLT WH 5/16x1 1/2 (4 PLCS) WASHER LOCK EXT 12x19 (4 PLCS) NUT BARREL WH 5/16x7/8 (4 PLCS) (1) M3 - ANGLE BRACE - W101121 5/8"x3 3/8"x52 1/2" (16x86x1335) STEP 8 (1) (1) BOLT WH 5/16x1 BOLT WH 5/16x1 1/2 NUT BARREL (1) WH 5/16x5/8 NUT BARREL (1) WH 5/16x7/8 (2) WASHER LOCK EXT 8x19 (2) WASHER LOCK EXT 12x19 NUT BARREL WH 5/16x7/8 (1 PLCS) M3 BOLT WH 5/16x1 1/2 (1 PLCS) BOLT WH 5/16x1 (1 PLCS) NUT BARREL WH 5/16x5/8 (1 PLCS) WASHER LOCK EXT 12x19 (2 PLCS) WASHER LOCK EXT 8x19 (2 PLCS) (1) N1 - CENTER RAIL - W101113 5/8"x2 3/8"x25 5/8" (16x60x652) (1) EJ - L BRACKET 54x67 - A100053 STEP 9 SCREW PFH 8x1 1/8 (2 PLCS) SCREW TAPPING 14x3/4 (2 PLCS) (2) SCREW TAPPING 14x3/4 (2) EJ N1 SCREW PFH 8x1 1/8 (5) M14 - WALL SLAT - W101115 5/8"x3 3/8"x25 5/8" (16x86x652) STEP 10 2-7/8" M14 SCREW PFH 8x1 1/8 (20 PLCS) (20) SCREW PFH 8x1 1/8 (6) M14 - WALL SLAT - W101115 5/8"x3 3/8"x25 5/8" (16x86x652) STEP 11 SCREW PFH 8x1 1/8 (24 PLCS) 2-7/8" (24) M14 SCREW PFH 8x1 1/8 (5) M14 - WALL SLAT - W101115 5/8"x3 3/8"x25 5/8" (16x86x652) STEP 12 2-7/8" SCREW PFH 8x1 1/8 (20 PLCS) (20) M14 SCREW PFH 8x1 1/8 (1) E5 - UPRIGHT - W101085 1 3/8"x3 3/8"x66" (36x86x1676) (1) E6 - UPRIGHT - W101120 1 3/8"x3 3/8"x66" (36x86x1676) M5 - TARP SUPPORT - W101125 5/8"x3 3/8"x44 1/4" (16x86x1124) (1) (2) M12 - TARP BRACE - W101089 5/8"x3 3/8"x41" (16x86x1042) STEP 13 (7) BOLT WH 5/16x1 1/2 (4) SCREW PFH 8x1 1/2 NUT BARREL (7) WH 5/16x7/8 M12 (7) WASHER LOCK EXT 8x19 (7) WASHER LOCK EXT 12x19 SCREW PFH 8x1 1/2 (4 PLCS) M5 E5 E6 M12 WASHER LOCK EXT 8x19 (7 PLCS) NUT BARREL WH 5/16x7/8 (7 PLCS) WASHER LOCK EXT 12x19 (7 PLCS) BOLT WH 5/16x1 1/2 (7 PLCS) (8) M15 - WALL SLAT - W101126 5/8"x3 3/8"x23 1/4" (16x86x591) STEP 14 (32) SCREW PFH 8x1 1/8 SCREW PFH 8x1 1/8 (32 PLCS) M15 2-7/8" 3-1/4" (4) D1 - PICNIC TABLE SUPPORT BRACE - W101117 1 3/8"x5 1/4"x17" (36x134x432) STEP 15 BOLT WH 5/16x2 1/2 (6) (2) (8) BOLT WH 5/16x3 WASHER LOCK EXT 8x19 NUT BARREL (8) WH 5/16x7/8 (8) BOLT WH 5/16x2 1/2 (6 PLCS) BOLT WH 5/16x3 (2 PLCS) WASHER LOCK EXT 8x19 (8 PLCS) NUT BARREL WH 5/16x7/8 (8 PLCS) WASHER LOCK EXT 12x19 (8 PLCS) WASHER LOCK EXT 12x19 (6) M10 - PICNIC TABLE BOARD - W101118 5/8"x3 3/8"x41 5/8" (16x86x1056) (2) N3 - TIE SLAT - W101119 5/8"x2 3/8"x8" (16x60x204) STEP 16 BUILD (2) BENCH ASSEMBLIES. M10 NOTE: HOLE ORIENTATIONS (6) M10 M10 N3 SCREW PFH 8x1 1/8 (3 PLCS) SCREW PFH 8x1 1/8 (2) BENCH ASSEMBLY STEP 17 (12) SCREW PFH 8x1 1/2 (12 PLCS) SCREW PFH 8x1 1/2 (2) L2 - OUTER WALL SLAT - W101100 5/8"x4 3/8"x39" (16x112x992) (1) (6) N2 - TIE SLAT - W101103 5/8"x2 3/8"x14 5/8" (16x60x372) (3) M13 - WALL SLAT - W101101 5/8"x3 3/8"x39" (16x86x992) M16 - CENTER WALL SLAT - W101102 5/8"x3 3/8"x20 3/8" (16x86x518) STEP 18 EVENLY SPACE BOARDS. (43) N2 SCREW PFH 8x1 1/8 (43 PLCS) L2 M13 M16 M13 L2 SCREW PFH 8x1 1/8 - WINDOW FRAME GREEN (1) EB 343x444.5 -A100044 STEP 19 (4) SCREW PWH 8x3/4 (4 PLCS) SCREW PWH 8x3/4 (2) L2 - OUTER WALL SLAT - W101100 5/8"x4 3/8"x39" (16x112x992) (1) (6) N2 - TIE SLAT - W101103 5/8"x2 3/8"x14 5/8" (16x60x372) (3) M13 - WALL SLAT - W101101 5/8"x3 3/8"x39" (16x86x992) M16 - CENTER WALL SLAT - W101102 5/8"x3 3/8"x20 3/8" (16x86x518) STEP 20 EVENLY SPACE BOARDS. (43) SCREW PFH 8x1 1/8 N2 SCREW PFH 8x1 1/8 (43 PLCS) L2 M13 M16 M13 L2 - WINDOW FRAME GREEN (1) EB 343x444.5 -A100044 STEP 21 (4) SCREW PWH 8x3/4 SCREW PWH 8x3/4 (4 PLCS) (4) M13 - WALL SLAT - W101101 5/8"x3 3/8"x39" (16x86x992) STEP 22 (16) M13 SCREW PFH 8x1 1/8 (16 PLCS) SCREW PFH 8x1 1/8 (1) M40 - STRIKE PLATE BLOCK - W101134 5/8"x3 3/8"x1" (16x86x24) (1) (1) GH - SCREW - A100145 SCREW O2 - DOOR MOUNTING RAIL - W101133 5/8"x1 3/8"x39" (16x34x992) (1) GJ - STRIKE PLATE - A100145 STRIKE STEP 23 (7) SCREW PFH 8x1 1/8 FLUSH O2 1-1/2" 10-1/2" GJ M40 GH SCREW PFH 8x1 1/8 (2 PLCS) SCREW PFH 8x1 1/8 (5 PLCS) (2) (1) M18 - DOOR BOARD - W100918 5/8"x3 3/8"x39 1/2" (16x86x1002) M21 - DOOR BOARD - W100919 5/8"x3"x38 1/4" (16x76x972) (2) (3) M22 - DOOR BOARD - W100921 5/8"x3 3/8"x25" (16x86x634) (2) FR - HINGE - A100093 LEAF 1 (1) HZ - KNOB - A100071 O1 - DOOR SUPPORT - W100923 5/8"x1 3/8"x19" (16x34x482) (2) GH - SCREW - A100145 SCREW (1) GK - WINDOW FRAME 216x267 BYD GREEN - A100146 (1) M20 - DOOR BOARD - W100920 5/8"x3"x38 1/4" (16x76x972) (2) M23 - DOOR BOARD - W100922 5/8"x3 3/8"x6 1/4" (16x86x160) (1) GF - MAGNETIC CATCH KIT - A100145 MAG STEP 24 SCREW PFH 8x1 1/8 (36 PLCS) (4) O1 M23 SCREW PWH 8x3/4 O1 (37) M20 (4) SCREW PPH 4x5/8 FR O1 GK M18 M21 HZ M18 M22 SCREW PFH 8x1 1/8 (1 PLCS) GF SCREW PWH 8x3/4 (4 PLCS) GH SCREW PFH 8x1 1/8 (1) DOOR ASSEMBLY STEP 25 (6) SCREW PPH 4x5/8 SCREW PPH 4x5/8 (6 PLCS) (4) (2) L3 - RAFTER - W100913 5/8"x4 3/8"x38 1/4" (16x112x972) (2) N5 - VERTICAL SUNBURST - W100915 5/8"x2 3/8"x12 7/8" (16x60x328) N4 - HORIZONTAL SUNBURST - W100914 N6 - ANGLED SUNBURST - W100916 (4) 5/8"x2 3/8"x32 7/8" (16x60x835) 5/8"x2 3/8"x7 7/8" (16x60x200) (2) DE - TRIANGLE PLATE 90 5 HOLE BYD GREEN - A100011 (2) HC - BYD ID TAG (LARGE) 2011 WITH AGES - A100164 STEP 26 SCREW PFH 8x1 1/8 (8 PLCS) BUILD (2) GABLE ASSEMBLIES (8) SCREW PWH 8x5/8 N6 N6 (10) N5 SCREW TAPPING 14x3/4 (16) N4 L3 SCREW TAPPING 14x3/4 (5 PLCS) L3 SCREW PWH 8x5/8 (4 PLCS) HC SCREW PFH 8x1 1/8 (2) GABLE ASSEMBLY STEP 27 (4) BOLT WH 5/16x1 1/2 NUT BARREL (4) WH 5/16x7/8 (4) WASHER LOCK EXT 8x19 (4) WASHER LOCK EXT 12x19 WASHER LOCK EXT 8x19 (4 PLCS) BOLT WH 5/16x1 1/2 (4 PLCS) NUT BARREL WH 5/16x7/8 (4 PLCS) WASHER LOCK EXT 12x19 (4 PLCS) (2) K91 - ROOF SLAT - W100917 3/8"x3 3/8"x50" (11x86x1270) STEP 28 SCREW PFH 8x1 1/4 (4 PLCS) (4) SCREW PFH 8x1 1/4 (22) K91 - ROOF SLAT - W100917 3/8"x3 3/8"x50" (11x86x1270) STEP 29 SCREW PFH 8x1 1/4 (44 PLCS) (44) SCREW PFH 8x1 1/4 (1) JZ - PICNIC TARP - A100143 STEP 30 (8) SCREW PWH 8x3/4 (8 PLCS) SCREW PWH 8x3/4 (2) EA - HAND GRIP YELLOW PLASTIC - A100043 STEP 31 (2) SCREW TAPPING 14x1-1/2 (2 PLCS) BOLT PTH 1/4x1 (2 PLCS) T-NUT 1/4 (2 PLCS) WASHER FLAT 9x18 (4 PLCS) WASHER LOCK INT 8x15 (4 PLCS) (2) BOLT PTH 1/4x1 (4) WASHER LOCK INT 8x15 (4) WASHER FLAT 9x18 (2) T-NUT 1/4 SCREW TAPPING 14x1-1/2 (1) LADDER ASSEMBLY STEP 32 WASHER LOCK EXT 8x19 (2 PLCS) LAG SCREW WH 5/16x2 (2 PLCS) (2) LAG SCREW WH 5/16x2 (2) WASHER LOCK EXT 8x19 (1) SWING BEAM ASSEMBLY STEP 33 T-NUT 5/16 (4 PLCS) BOLT HEX 5/16x1 1/4 (4 PLCS) (4) (4) BOLT HEX 5/16x1 1/4 (4) (4) WASHER SPLIT 5/16 (4 PLCS) WASHER FLAT 8x27 (4 PLCS) WASHER FLAT 8x27 WASHER SPLIT 5/16 T-NUT 5/16 (2) FB - SWING SEAT YELLOW - A100070 (1) DL - GLIDER SEAT YELLOW - A100023 (2) DK - GLIDER ARM BYD GREEN - A100022 (8) FA - QUICK LINK - A100069 STEP 34 TIGHTEN QUICK LINK (2) NUT LOCK 5/16 (2) WASHER FLAT 8x27 INSERT CHAIN INTO QUICK LINK (2) FA NUT LOCK 5/16 (2 PLCS) WASHER FLAT 8x27 (2 PLCS) BOLT WH 5/16x5 3/4 (2 PLCS) BOLT WH 5/16x5 3/4 (1) SLIDE ASSEMBLY STEP 35 7 5/8" 2 5/8" 1" 2 5/8" (3) BOLT WH 5/16x1/2 (3) WASHER LOCK EXT 8x19 (3) BOLT WH 5/16x1/2 (3 PLCS) WASHER LOCK EXT 12x19 (3 PLCS) NUT BARREL WH 5/16x5/8 (3 PLCS) NUT BARREL WH 5/16x5/8 (1) TELESCOPE KIT - 1992 STEP 36 (1) (1) SCREW PTH #14x2-1/2 FLANGE CUP WASHER (6) KD - PLASTIC GROUND STAKE BROWN - A100179 Anchoring Instructions NOTE: FAILURE TO USE GROUND STAKES CAN VOID WARRANTY & CAUSE INJURY! STAKE A (6) GROUND STAKE SCREW PFH 8x2 GROUND STAKE STEP 37 GROUND STAKE GROUND STAKE DRIVE GROUND STAKE INTO GROUND AND FASTEN WITH 2" SCREW. FINAL STEP DOUBLE CHECK EVERY BOLT, SCREW AND NUT FOR TIGHTNESS. MAKE SURE EVERY BOARD IS SECURE AND MAKE SURE THE PLAY SET IS LEVEL. ENJOY YOUR NEW PLAY SET! SCREW PFH 8x2 (6 PLCS) GROUND STAKE GROUND STAKE Limited Warranty This Limited Warranty by Backyard Discovery applies to products manufactured under the Backyard Discovery brand or its other brands including but not limited to Backyard Botanical, Adventure Playsets, and Leisure Time Products. Backyard Discovery warrants that this product is free from defect in materials and workmanship for a period of one (1) year from the original date of purchase. This one (1) year warranty covers all parts including wood, hardware, and accessories. All wood carries a five (5) year pro-rated warranty against rot and decay. Refer to the schedule below for charges associated with replacement of parts under this Limited Warranty. In addition, Backyard Discovery will replace any parts within the first 30 days from date of purchase found to be missing from or damaged in the original packaging. This warranty applies to the original owner and registrant and is non-transferable. Regular maintenance is required to assure maximum life and performance of this product and failure by the owner to maintain the product according to the maintenance requirements may void this warranty. Maintenance guidelines are provided in the Owner’s Manual. This Limited Warranty does not cover: • • • • • • • • Labor for any inspection Labor for replacement of any defective item(s) Incidental or consequential damages Cosmetic defects which do not affect performance or integrity of a part or the entire product Vandalism, improper use, failure due to loading or use beyond the capacities stated in the applicable Assembly Manual. Acts of nature including but not limited to wind, storms, hail, floods, excessive water exposure Improper installation including but not limited to installation on uneven, unlevel, or soft ground Minor twisting, warping, checking, or any other natural occurring properties of wood that do not affect performance or integrity Backyard Discovery products have been designed for safety and quality. Any modifications made to the original product could damage the structural integrity of the unit leading to failure and possible injury. Modification voids any and all warranties and Backyard Discovery assumes no liability for any modified products or consequences resulting from failure of a modified product. This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a Backyard Discovery product be used in public settings. Such use may lead to product failure and potential injury. Any and all public use will void this warranty. Backyard Discovery disclaims all other representations and warranties of any kind, express or implied. This Warranty gives you specific legal rights. You may have other rights as well which vary from state to state or province to province. This warranty excludes all consequential damages, however, some states do not allow the limitation or exclusion of consequential damages and therefore this limitation may not apply to you. Pro Rated Part Replacement Schedule Product Age All Parts 0-30 days from date of purchase 31 days to 1 year Customer Pays $0 and free shipping $0 + S&H Wood Rot and Decay Only 1 year 2 years 3 years 4 years 5 years Over 5 years $0 and free shipping 20% + S&H 40% + S&H 60% + S&H 80% + S&H 100% + S&H Rev5/20/10 BRS ">
Advertisement
