MAN0935-06-EN_599DQMx06_Datasheet Specifications / Installation
1
SmartRail
12/24VDC Output Modules
Specifications
Number of outputs
Commons per Module
Output Voltage Range
Rated Output Current
Max. Inrush Current
Off Leakage Current
Max. Voltage Drop (On)
Response Time
Isolation
LED indication
Backplane Power
Consumed @5V
(all outputs on)
Terminal Type
Optional Spring Clamp
Terminal Strips
Specifications
DQM506
8
DQM606
16
DQM706
32
1
12/24VDC (10.2 – 26.4VDC)
0.5A/pt 0.2A/pt
2A/common
4A for 10ms
0.1mA or less
0.4VDC or less
1ms or less
500VDC or greater
Labeled 1-8 for each output group
40mA 60mA
M2 Screw Type,
Removable
HE599
HE599
TRM010
TRM010 +
HE599
TRM008
Number of Terminals
Terminal Torque Rating
10 posn
10 posn +
8 posn
0.22 to 0.25 N-m
1.95 to 2.21 in-lbs
40-pins
1.2 N-m
10.6 in-lbs
16-28 AWG (use copper) Accepted Wire Size
Wire Stripping Length
General Specifications
7mm
Storage Temp.
Operating Temp.
DQM506 DQM606
-25
to 70
Celsius
-0
to 55
Celsius
DQM706
Relative Humidity
Dimensions WxHxD
5 to 95% Non-condensing
20mm x 90mm x 60mm
0.7
9” x 3.54” x 2.36”
Weight
CE & UL Compliance
30g
(1.1 oz.)
40g
(1.4 oz.)
60g
(2.1 oz.)
CE, UL & C-UL
Class I, Div 2 Groups A, B, C & D
HE599DQM506 (8pt), HE599DQM606 (16pt), HE599DQM706 (32pt)
Positive Logic
120mA
M3 Fixed
None
GROUP A
GROUP B
GROUP C
GROUP D
12/24VDC
+
3
4
1
2
7
8
5
6
5
6
7
2
3
8
1
4
5
6
7
4
5
6
7
8
1
2
3
3
4
1
2
8
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
TERMINAL
A01
B01
A02
A12
B12
A13
B13
A14
B14
A15
B15
A16
B16
A17
B17
A18
B18
A19
B19
A20
B20
A07
B07
A08
B08
A09
B09
A10
B10
A11
B11
B02
A03
B03
A04
B04
A05
B05
A06
B06
DQM706 Wiring (SmartLink Terminal Strip)
2 Wiring – I/O
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
A
L
L
L
L
1
2
3
4
GROUP A LEDs
GROUP B LEDs
LOAD
LOAD
LOAD
LOAD
L
L
L
L
L
L
L
1
2
3
4
5
6
7
-
L
+
8
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
24VDC
L
L
L
L
B
L
L
L
L
L
L
5
6
7
8
1
2
3
4
5
6
7
L
-
L
+
8
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
24VDC
C
12/24
VDC
12/24
VDC
C
DQM706 Wiring
40-pin IDE Header cannot be
DQM506 Wiring DQM606 Wiring
directly wired. SmartLink
Terminal Strip recommended
__________________________________________________________________________________________________________________________________________________________________
5/22/2018 Page 1 of 3
MAN0935-06-EN_599DQMx06_Datasheet
2.1 Output Wring Terminals
Description
SmartLink Wiring Accessories
Part Number
DIN-rail mounted
Barrier Style Terminal Strip
Terminal Strip Cable, 0.5m
Terminal Strip Cable, 2.0m
HE599TRM040
HE599CBL040
HE599CBL240
DIN-rail mounted
32-point Relay block
Relay Adapter Cable, 0.5m
Relay Adapter Cable, 2.0m
HE599RLY037
HE599CBL037
HE599CBL237
D
C
B
8
+12/24V
Common
4
5
6
7
1
2
3
4
5
6
7
8
7
8
1
2
3
5
6
7
+12/24V
8
1
2
3
4
Common
1
2
3
4
5
6
Group Output
A
No Connect
DQM506 Terminal
10posn – Terminal 1
10posn – Terminal 2
10posn – Terminal 3
10posn – Terminal 4
10posn – Terminal 5
10posn – Terminal 6
10posn – Terminal 7
8posn – Terminal 1
8posn – Terminal 2
8posn – Terminal 3
8posn – Terminal 4
8posn – Terminal 5
8posn – Terminal 6
8posn – Terminal 7
10posn – Terminal 8
10posn – Terminal 9
8posn – Terminal 8
10posn – Terminal 9
10posn – Terminal 10 10posn – Terminal 10
10posn – Terminal 1
10posn – Terminal 2
10posn – Terminal 3
N/A
10posn – Terminal 4
10posn – Terminal 5
10posn – Terminal 6
10posn – Terminal 7
10posn – Terminal 8
N/A
N/A
N/A
N/A
DQM606 Terminal
N/A
N/A
N/A
N/A
A12
A11
A10
A09
A08
A07
A06
A05
B01
A01
B04
B03
A04
A03
B06
B05
A20
A19
A18
A17
A16
A15
A14
A13
DQM706
Pin
B20
B19
B18
B17
B16
B15
B14
B13
B02
A02
B12
B11
B10
B09
B08
B07
Note: Groups A, B, C & D are share the same +12/24V & Common terminals.
2.2 SmartLink Wiring Accessories (DQM706)
The DQM706 32-pt DC Output module utilizes a 40pin IDC male connector for user connections. SmartLink Wiring Accessories can be used with the DQM706 to provide a more convenient wiring method. These DIN-rail mounted options consist of a barrier style,
40position terminal strip (TRM040) and a 32-point replaceable relay block (RLY037) connected to the front of the DQM706 with a 40pin round cable. This cable is available with two different pinouts, and in 0.5m or 2.0m lengths. The table below lists the part numbers for the SmartLink Wiring Accessories compatible with the HE599DQM706 input module.
NOTE: The TRM040 and RLY037 accessories utilize different cables. They are highdensity cables, and the pin out on the accessory side of the unit is different..
Specifications / Installation
HE599TRM040
40-Pin Din Rail Mounted Terminal Strip for DQM706
General Specifications
Rated Voltage
Rated Current
Withstanding voltage
Applicable cable
T/B screw
Screw torque
Ambient temperature rating
Dimensions (L x W x D)
AC, DC 125V
1A
600V
1.25mm/max
M3 x 10L
1.2 N-m (12kgf / cm)
-10°C to 50°C (non-condensing)
149mm x 40mm x 36.8mm
HE599CBL040 (Shown)
.5m Cable for Terminal Strip TRM040 to DQM706 module
HE599CBL240
2.0m Cable for Terminal Strip TRM040 to DQM706 module
Note: Connector with ~80° angle connector must be inserted into the
Terminal Strip. Straight connector must be inserted into the DQM706
Module.
__________________________________________________________________________________________________________________________________________________________________
5/22/2018 Page 2 of 3
MAN0935-06-EN_599DQMx06_Datasheet
HE599RLY037
32-Point Din Rail Mount Relay Block for DQM 706
General Specifications
Contact Arrangement
Resistive Load
Max Switching Current
Max switching voltage
Coil Nominal Voltage
Pick-up voltage
Drop-out voltage
Coil Resistance
Nominal Operating Power
Surge Voltage between contact and Coil
Initial Breakdown Voltage between Contact and Coil
1a
5A 250VAC
5A
250VAC
24VDC
16.8VDC
1.2VDC
3200 Ω
180mW
4000V
2000V rms
Installed Relay
I/O Count
Coil Voltage Rating
Coil Side Interface
Contact Side Interface
Dimensions (L x W x D)
Terminal Screw
Terminal Screw Torque
Ambient Temperature Rating
Matsushita PA1a-24v
32-point (1 A)
24VDC
Mil-C 83503 40 pin
Screw terminal block
174mm x 70mm x 39.5mm ; din rail
M3 x 8L
1.2 N-m (12kgf / cm)
-10°C to 50°C (non-condensing)
HE599CBL037 (Shown)
0.5m Cable for Relay Block RLY037 to DQM706 module
HE599CBL237
2.0m Cable for Relay Block RLY037 to DQM706 module
Specifications / Installation
3 Configuration DATA
The SmartRail digital output modules are configurable to “hold last state” if desired – when communications is lost with the controlling CPU. This is not configurable on a point-by-point basis, but rather by a group-by-group basis (8points/group). Cscape
(9.1 or later) is required for configuration:
Cscape Configuration Data – Selectable per Group
Parameter
Hold Last
State
(Yes or No)
Selections
Group A
(outputs 1-8)
Group B
(outputs 9-16)
Group C
(outputs 17-24)
Group D
(outputs 25-32)
DQM506
X
N/A
DQM606
X
X
N/A
DQM706
X
X
X
X
4 Installation / safety
This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D or
Non-hazardous locations only
WARNING - EXPLOSION HAZARD -
Do not disconnect equipment unless power has been removed or the area is known to be non-hazardous
WARNING - EXPLOSION HAZARD -
Substitution of any component may impair suitability for Class I, Division 2
WARNING – POSSIBLE EQUIPMENT DAMAGE
Remove power from the I/O Base and any peripheral equipment connected to this local system before adding or replacing this or any module. a. All applicable codes and standards should be followed in the installation of this product.
For detailed installation and a handy checklist that covers panel box layout requirements and minimum clearances, refer to the hardware manual of the controller you are using.
When found on the product, the following symbols specify:
Warning: Electrical
Shock Hazard.
Warning: Consult user documentation.
5 Technical Support
Technical Support at the following locations:
North America:
Tel: 317 916-4274
Fax: 317 639-4279
Web: http://www.hornerautomation.com
Email: [email protected]
Europe:
Tel: +353-21-4321266
Fax: +353-21-4321826
Web: http://www.horner-apg.com
Email: [email protected]
No part of this publication may be reproduced without the prior agreement and written permission of Horner APG, Inc. Information in this document is subject to change without notice.
NOTE: Connector with ~80° angle connector must be inserted into the
Relay block. Straight connector must be inserted into Module
__________________________________________________________________________________________________________________________________________________________________
5/22/2018 Page 3 of 3
