null  null
Cybex Eagle® Row
Owner’s Manual
Strength Systems
Part Number 11030-999-4 A
www.cybexinternational.com
Cybex Eagle® Row
Owner’s Manual
Strength Systems
Part Number 11030-999-4 A
Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc.
Eagle® and its mark are registered trademarks of Cybex International, Inc.
DISCLAIMER: Cybex International, Inc., makes no representations or warranties regarding the contents of this manual. We reserve the right to
revise this document at any time or to make changes to the product described within it without notice or obligation to notify any person of such
revisions or changes.
© Copyright 2010, Cybex International, Inc. All rights reserved.
Printed in the United States of America.
10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX 508-533-5183
www.cybexinternational.com • [email protected] • 11030-999-4 A
Table of Contents
1 Safety
Safety. . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Guidelines and Practices . . . . .
Warning/Caution Decals . . . . . . . . . . .
Regular Maintenance Activities . . . . . .
Using Proper Form . . . . . . . . . . . . . . .
1-1
1-2
1-3
1-5
1-5
2 Exercises
Intended Use . . . . . . . . . . . . . . . . . . . . 2-1
Instructions. . . . . . . . . . . . . . . . . . . . . . 2-1
3 Customer Service
Contacting Service. . . . . . . . . . . . . . . .
Ordering parts . . . . . . . . . . . . . . . . . . .
Return Material Authorization (RMA). .
Damaged Parts . . . . . . . . . . . . . . . . . .
3-1
3-1
3-1
3-2
4 Assembly
Assembly . . . . . . . . . . . . . . . . . . . . . . . 4-1
5 Maintenance
Daily Procedures . . . . . . . . . . . . . . . . .
Weekly Procedures . . . . . . . . . . . . . . .
Yearly Procedures . . . . . . . . . . . . . . . .
Environment. . . . . . . . . . . . . . . . . . . . .
Storage . . . . . . . . . . . . . . . . . . . . . . . .
Page i
5-1
5-4
5-6
5-7
5-7
Cybex Eagle 11030 Row Owner’s Manual
1 - Safety
Safety
Read the Owner’s Manual carefully before assembling, servicing or using the equipment.
It is the responsibility of the facility owner and/or owner of the equipment to instruct users on proper operation of the
equipment and review all labels.
WARNING: Serious injury could occur if these safety precautions are not observed:
User Safety Precautions
•
Obtain a medical exam prior to beginning an exercise program.
•
Read and understand warning labels and user manual prior to exercising. Obtain instruction
prior to use.
•
Keep body and clothing free from and clear of all moving parts.
•
Inspect machine prior to use. DO NOT use if it appears damaged or inoperable.
•
DO NOT attempt to fix a broken or jammed machine. Notify floor staff.
•
Use the machine only for the intended use. DO NOT modify the machine.
•
Be sure that the weight pin is completely inserted. Use only the pin provided by the manufacturer.
If unsure seek assistance.
•
Never pin the weights in an elevated position. DO NOT use the machine if found in this condition.
See assistance from floor staff.
•
Children must not be allowed near these machines. Teenagers must be supervised.
•
DO NOT use if guards are missing or damaged.
•
DO NOT use dumbbells or other incremental weights, except those provided by the manufacturer.
•
Inspect all cables and belts and connections prior to use. DO NOT use if any components are worn, frayed or
damaged.
•
DO NOT remove any labeling from equipment. Replace any damaged labels.
•
Stop exercising if you feel faint, dizzy or experience pain at any time while exercising and consult your
physician.
Facility Safety Precautions
•
Read the Owner’s Manual carefully before assembling, servicing or using the equipment.
•
Securely anchor each machine to the floor using the anchor holes provided in each machine.
NOTE: Cybex is not responsible for the actual anchoring of equipment. Consult with a professional
contractor.
NOTE: Use fasteners having a minimum of 500 lbs. tensile capacity (3/8” grade 2 bolts or better).
NOTE: If legs/frame does not contact surface, DO NOT pull down with anchors. Shim any
leg or frame not in contact with surface using flat washers.
Safety
Page 1-1
Cybex Eagle 11030 Row Owner’s Manual
•
Make sure that each machine is set up and operated on a solid level surface. Do not install equipment on an
uneven surface.
•
Make sure that all users are properly trained on how to use the equipment.
•
Make sure there is enough room for safe access and operation of the equipment.
•
Perform regular maintenance checks on the equipment. Also pay close attention to all areas most susceptible to wear,
including (but not limited to) cables, pulleys, belts and grips.
•
Immediately replace worn or damaged components. If unable to immediately replace worn or damaged components
then remove from service until the repair is made.
•
Use only Cybex supplied components to maintain/repair the equipment.
•
Keep a repair log of all maintenance activities.
•
Inspect all cables and belts and connections prior to use. DO NOT use if any components are worn, frayed or
damaged.
NOTE: It is the sole responsibility of the user/owner or facility operator to ensure that regular maintenance is performed.
Safety Guidelines And Practices
Cybex recommends that all fitness equipment be used in a supervised area. It is recommended that the equipment be
located in an access controlled area. Control is the responsibility of the owner. The extent of control is at the discretion of
the owner.
It is the responsibility of the purchaser/user of Cybex products to read and understand the owner’s manual, and warning
labels; as well as instruct all individuals, whether end users or supervising personnel, on proper usage of the equipment.
PROPER USAGE:
Use machine only as described in the manual. Failing to follow proper instructions may result in injury.
Do Not Lean Against or Pull On the framework, weight stack, or any component, whether machine is at rest or in use.
Inappropriate or improper use may result in injury to users or third parties (bystanders).
Do not use machine if it is not located on a solid level surface or is improperly installed.
Provide an adequate safety perimeter between the machine, walls and other equipment to ensure that the facility has the
proper clearance for usage and training.
SECURING EQUIPMENT:
The machine has holes in the feet, which allow for ease in anchoring to the floor. Cybex strongly recommends that,
to eliminate rocking, tipping or falling over due to incorrect usage and misuse, equipment be secured to a solid, level
surface.
1. The solid, level surface should not deviate more than 1/8” over a 10’ distance or as defined and required by local
building and architectural codes.
2. Anchoring of equipment must be completed by a qualified licensed contractor.
Safety
Page 1-2
Cybex Eagle 11030 Row Owner’s Manual
3. Anchoring holes are provided on the feet of the frame. All anchoring locations must be used when anchoring the
equipment to the floor.
4. Due to the wide variation of flooring on which machines may be anchored or installed, verify anchoring method and
anchoring fasteners with a qualified and licensed contractor.
5. A minimum pull out force of 220 lbs/100 kgs is required for each anchor position..
6. Do not use machine until it is properly anchored.
MAINTENANCE:
Preventative maintenance allows proper equipment operation and reduces the risk of injury. Perform the maintenance
requirements as specified in the manual.
STANDARD COMPLIANCE:
Cybex products meet or exceed applicable ASTM and EN Standards.
Warning/Caution Decals
Warning decals indicate a potentially hazardous situation, which, if not avoided, could result in death or serious injury.
Caution decals indicate a potentially hazardous situation, which, if not avoided, could result in minor or moderate injury.
The warning and caution decals are shown on the following page. The diagrams following the decals show where each
decal is located.
Safety
Page 1-3
Cybex Eagle 11030 Row Owner’s Manual
A
CAUTION
Personal injury may occur.
Keep away from moving
parts to avoid injury.
4000Y316-4 A
B
C
CAUTION
Safety
Page 1-4
Cybex Eagle 11030 Row Owner’s Manual
Row - 11030
B
B
B
A
B
C
DESCRIPTION
PART NO.
A. Warning Decal ..............4605-381-4
B. Caution Decal ...............4000Y316-4
C. Caution Decal ...............4520-362-4
Safety
Page 1-5
Cybex Eagle 11030 Row Owner’s Manual
Regular Maintenance Activities
Preventative maintenance activities must be performed to maintain normal operation of your equipment. Keeping
a log sheet of all maintenance actions will assist you in staying current with all preventative maintenance activities.
The preventative maintenance actions are described in detail in Chapter 5.
Briefly, they include:
Daily
1. Clean upholstery.
Weekly
1. Inspect all nuts and bolts for looseness. Tighten as required.
2. Inspect all cables and belts for damage or wear (see Chapter 5). If a cable or belt is worn or damaged,
immediately discontinue use until cable or belt has been replaced.
3. Check for worn handles, worn snap links, and worn warning labeling. Replace all worn parts immediately.
4. Inspect for loose or worn grips. Replace all loose or worn grips immediately.
5. Inspect weight stacks for proper alignment and operation. Correct all improper alignmentand operation issues
immediately.
6. Lubricate guide rods using automotive engine oil only.
Yearly
1. Replace all cables and belts at least annually.
Using Proper Form
Before working out, read and understand the exercises located on the placard and in Chapter 2.
Safety
Page 1-6
Cybex Eagle 11030 Row Owner’s Manual
2 - Exercise
MUSCLES USED
Intended Use
The intended use of this equipment is to aid or
improve general physical fitness and exercise.
For Commercial use.
Instructions
Read and understand all instructions and warnings
prior to using this machine. See Chapter 1, Safety in
the Eagle Owner’s Manual or consult with floor staff.
START
Lattisimus Dorsi, Teres Major, Biceps,
Middle Trapezius, Rear Deltoid,
Rhomboideltoid
FINISH
NOTE: Motion Developed: Shoulder Extension, Elbow Flexion
NOTE: Do not turn knob when weight stack is elevated
NOTE: All adjustment points on the machine have yellow handles or knobs.
NOTE: See next page for “Set Up” and “Movement”.
Exercise
Page 2-1
Cybex Eagle 11030 Row Owner’s Manual
Set Up
1. Adjust chest pad to allow comfortable reach of handles.
2. Grasp handles with hands in front of and level with the shoulders.
Movement
1. Pull the handles towards you until your elbows are at your sides.
Exercise
Page 2-2
Cybex Eagle 11030 Row Owner’s Manual
3 - Customer Service
Contacting Service
Hours of phone service are Monday through Friday from 8:30 a.m. to 6:00 p.m Eastern Standard Time.
For Cybex customers living in the USA, contact Cybex Customer Service at 888-462-9239.
For Cybex customers living outside the USA, contact Cybex Customer Service at 508-533-4300 or fax 508-533-5183.
Find information on the web at www.cybexintl.com or e-mail at [email protected]
Ordering Parts
Fax orders to 508-533-5183. To speak with a customer service
representative, call 888-462-9239 (for customers living within
the USA) or 508-533-4300 (for customers outside the USA).
You may also contact us through e-mail at
[email protected]
Having the following information ready when calling, will assist our
Cybex representatives in serving you.
•
Unit Serial Number
•
Product Name
NOTE: All inspections
and repairs must be
performed by trained
service personnel only
Cybex will void warranty if
non-Cybex replacement parts
are used.
The unit serial number and product name can be found on the serial number decal.
•
Part Description
•
Part Number
Part descriptions and part numbers are located on the web at www.cybexintl.com.
•
Shipping Address
•
Contact Name
In addition to your shipping address and contact name, your account number is helpful but not required.
Return Material Authorization (RMA)
The Return Material Authorization (RMA) system outlines the procedures to follow when returning
material for placement, repair or credit. The system assures that returned materials are properly handled and analyzed. Follow the
following procedures carefully.
Contact your authorized Cybex dealer on all warranty-related matters. Your local Cybex dealer will request a RMA from Cybex, if
applicable. Under no circumstances will defective parts or equipment be accepted by Cybex without proper RMA and an Automated
Return Service (ARS) label.
Customer
Service
Page 3-1
Cybex Eagle 11030 Row Owner’s Manual
1. Call the Customer Service Hot Line listed above for the return of any item that is defective.
2. Provide the technician with a detailed description of the problem you are having or the defect in the item you wish
to return.
3. Provide the model and serial number of your Cybex equipment.
4. At Cybex’s discretion, the technician may request that you return the problem part(s) to Cybex for evaluation and
repair or replacement. The technician will assign you a RMA number and will send you an ARS label. The ARS
label and the RMA numbers must be clearly displayed on the outside of the package that contains the item(s) to be
returned. Include the description of the problem, the serial number of the equipment and the name and address of
the owner in the package along with the part(s).
5. Forward the package through UPS to Cybex.
Attn: Customer Service Department
Cybex International, Inc.
1975 24th Ave SW
Owatonna, MN 55060
NOTE: Merchandise returned without an RMA number on the outside of the package or shipments sent COD will not be
accepted by the Cybex receiving department.
Damaged Parts
Materials damaged in shipment should not be returned for credit. Shipping damages are the responsibility of the carrier (UPS, Federal
Express, trucking companies, etc.)
Apparent Damage - Upon receipt of your shipment, check all items carefully. Any damage seen with a visual check must be noted
on the freight bill and signed by the carrier’s agent. Failure to do so will result in the carriers refusal to honor your damage claim. The
carrier will provide you with the required forms for filing such claims.
Concealed Damage - Damage not seen with a visual check upon receipt of a shipment but notices later must be reported to the carrier
as soon as possible. Upon discovery of the damage, a written or phone request to the carrier asking them to perform an inspection
of the materials must be made within ten days of the delivery date. Keep all shipping containers and packing materials as they will be
needed in the inspection process. The carrier will provide you with an inspection report and the necessary forms for filing a concealed
damage claim. Concealed damage claim is the carrier’s responsibility.Cybex, if applicable. Under no circumstances will defective parts
or equipment be accepted by Cybex without proper RMA and an Automated Return Service (ARS) label.
Customer
Service
Page 3-2
Cybex Eagle 11030 Row Owner’s Manual
4 - Assembly
TOOLS REQUIRED
•
•
•
•
•
•
•
ITEM
7/32” Allen wrench
3/4” Allen wrench
9/16” Wrench
External snap ring pliers
Phillips screwdriver
Medium weight automotive engine oil
Torque Wrench
1
2
3
1
QTY
PART NO.
DESCRIPTION
4
1
13
11090-392
12000-560
4000C101
FOOT PAD
DECAL, WEIGHT PLATE (30 - 290)
WEIGHT STACK PLATE
2
30
22.5
31.5
90
40.5
110
49.5
130
58.5
150
67.5
170
NOTE: Two people will be required for this procedure.
3
76.5
190
85.5
210
94.5
230
NOTE: It is the responsibility of the facility owner/owner of
the equipment to ensure that there is appropriate
clearance around each machine to allow for safe use and passage.
13.5
50
70
103.5
250
112.5
270
121.5
290
130.5
1. Read and understand all instructions thoroughly before starting any of the procedures
listed on this instruction sheet.
2. Verify you have received the appropriate configuration.
A. Verify that you received the correct color machine that you ordered.
B. Verify you received weight plates and weight plate decals.
C. Verify you received the Cybex Eagle Row Owner’s Manual.
D. Verify you received the warranty sheet.
3. Move to desired location.
A. Note the diminsions of the machine:
Idle 54 L x 58 W x 72 H inches
137.16 L x 147.32 W. x 182.88 H cm
In use - 54 L x 58 W x 72 H inches
137.16 L x 147.32 W. x 182.88 H cm
Machine Weight with weight stack - 736 lbs. (333.84 kg)
B. Determine if you can move your machine through the required doorway(s).
C. If the machine fits through the the doorway(s), move machine to desired location and skip to step 5.
D. If weight stacks need to be installed proceed to step 6.
E. If the machine does not fit through the door-way(s) then see step 4.
4. Doorway Instructions.
NOTE: If your machine fits through the doorway then skip step 4.
If your machine does not fit through the doorway, then perform step 4.
A. Carefully remove each (standard) cone-shaped shipping support using a 3/4” socket or wrench.
B. Make a note of the current belt routings and connections. This will assist you in reinstalling them properly.
Assembly
Page 4-1
Cybex Eagle 11030 Row Owner’s Manual
C. Cut shipping tie securing top weight.
Cam
D. Rotate cam and disconnect weight stack belt from cam
(by loosening the two set screws on the belt clamp with a
7/32” Allen wrench). See Figure 1.
E. Locate the pulley bracket that is located near the cam.
See Figure 2.
Set
Screws
Figure 1
Hex Nut/Washer
Pulley
Bracket
F. Remove bolt, washer and hex nut securing the pulley to
the pulley bracket.
G. Remove pulley from pulley bracket.
H. Using a Phillips screwdriver, remove the two screws securing the
cam cover plate (guard) and remove the plate. See Figure 3.
I.
Bolt
At the opposite end of the pivot shaft (from step 4H),
locate the small plate shown in Figure 4.
Figure 2
J. Using a 7/32” Allen wrench, remove the two BHSCS
securing the small plate and remove the plate.
K. Remove one of the two BHSCS securing the pivot shaft.
See Figure 5.
Screw
L. Carefully remove pivot shaft. See Figure 5. NOTE: Be
extremely careful when removing shaft so you don’t ruin
the threads on the shaft.
M. Rotate cam so that the flat part is facing down.
N. Carefully slide pulley shaft out of machine.
Cam Cover Plate
Figure 3
BHSCS (2)
Small Plate
Figure 4
Washer
Pulley Shaft
BHSCS
Pivot Shaft
Pulley/Cable
Figure 5
Assembly
Page 4-2
Cybex Eagle 11030 Row Owner’s Manual
O. With an assistant, carefully remove the six BHSCS
securing the two halves of the frame. See Figure 6.
BHSCS (qty 6)
P. Carefully lay the taller half of the frame down on the
floor until you are ready to move it.
Q. Carefully move each half through the door-way to the
desired location. Again, lay the taller half of the frame
down on the floor until you are ready to reattach the two
halves.
R. With an assistant, carefully attach each half together
using the six BHSCS removed in step 4O. See Figure 6.
Nylon Locknut (6)
Figure 6
S. With the flat part facing down, carefully slide the pulley
shaft back into the machine (removed from steps 4M
and 4N).
T. Carefully slide the pivot shaft through the pulley shaft
(removed from steps 4K and 4L).
U. Secure the pivot shaft using the BHSCS removed in
step 4K.
Phillips Head
Screw (3)
Figure 7
V. Reconnect the pulley to the pulley bracket (removed in
steps 4F and 4G).
W. Verify the two belts are routed properly (one belt connecting from the cam to
the pulley bracket and the other belt connecting from the pulley to the arms).
Screw (loosen do not remove)
X. Connect the weight stack belt to the belt clamp of cam (removed in step 4D).
See Figure 1.
Y. Continue on with Step 5C.
Figure 8
5. Remove shipping feet and remove the back shrouds.
A. Carefully remove each (standard) cone-shaped
shipping support using a 3/4” socket or wrench.
B. Cut shipping tie securing top weight.
C. Carefully place rubber feet (supplied with machine)
on each foot of the frame.
Screw
Figure 9
D. Lift top weight and turn the Increment Weight Adjusting Knob to select all 15 lbs. (three increment weights
each side).
E. Remove the three Phillips head screws securing the top (back) shroud and carefully remove the shroud.
See Figure 7.
F. Loosen bottom two screws shown in Figure 8. NOTE: Do not remove the bottom two screws.
G. Remove the top two screws securing the back shroud. See Figure 9.
H. Carefully slide rear shroud assembly upward and remove.
Assembly
Page 4-3
Cybex Eagle 11030 Row Owner’s Manual
6. Install the weight stack.
Frame
A. Note how the increment weights are installed.
Upper snap ring
B. With an assistant holding the increment weights,
move the adjusting knob to 0 lbs. and remove all six
increment weights (three each side).
Wave washer
C. Using an external snap ring pliers, remove the upper
snap ring from one of the guide rods and carefully lower
the guide rod. See Figure 10.
Guide rod
Lower snap ring
Figure 10
D. Remove lower snap ring and wave washer from the guide rod. Repeat steps 6C and 6D to remove
both snap rings from other guide rod.
E. If possible, lean guide rods outward, away from machine in order to provide the most room for
installing weight plates.
F. Carefully slide top weight/second plate up and out of machine and carefully set it aside.
G. Wipe guide rods clean over entire length. Lubricate with light coating of medium weight automotive engine oil.
H. Carefully install each weight plate one at a time. NOTE: When installing weight plates, position plates
so wide edges of bushing face upward and narrow edges of bushing face downward. See Figures 11A
and 11B.
T
C
RE
G
N
RO
R
O
C
WIDE bushing
edge faces
upward
Figure 11A
I.
W
NARROW
bushing edge
NOTE: The narrow bushing
edge must face downward.
Figure 11B
Carefully slide the top weight/second plate onto the guide rods.
J. Place lower snap ring and wave washer onto guide rod (about 3” from the top end of guide rod).
K. Raise guide rod up through mounting hole and install the upper snap ring.
L. Lower guide rod and secure lower snap ring. Repeat steps 6J - 6L for the other guide rod.
Assembly
Page 4-4
Cybex Eagle 11030 Row Owner’s Manual
7. Belt Routing.
A. Verify belt is routed through top of pulley bracket and
then route end of belt down to the top weight.
B. Carefully lift top weight and verify that the position of
the belt clamp (on the top weight) is aligned properly
with the top pulley bracket (on the machine). See
Figure 12.
C. Slide belt through slot in belt clamp.
D. Verify belt and insert are installed properly, as shown
in Figure 13A. NOTE: Do not install the insert
backwards as shown in Figure 13B.
E. Pull belt tight and secure belt to clamp with the two
set screws. NOTE: Torque set screws 300-350 in./lbs.
See Figure 14.
Insert and Set Screws (not
shown) are on this side.
Belt
Increment
Weight
Adjusting
Knob
Top Pulley
Figure 12 (top view from pulley down to belt clamp)
Correct belt routing
Wrong belt routing
Insert
Insert
Belt
Belt
Stem
Stem
Figure 13A
Figure 13B
F. Place weight stack pin in each plate to verify proper
installation.
G. Without selecting any resistance, lift top weight up and
down (simulating normal operation).
Belt
H. Have an assistant verify that the belt is moving smoothly
and is routed straight from the top pulley bracket to the
to weight belt clamp.
I.
Reinstall the six increment weights that were removed
in step 6B. See Figure 15.
Belt clamp
insert
Belt clamp
Set screws
J. Turn the Increment Weight Adjusting Knob to select all
15 lbs.
8. Install back shrouds.
A. Carefully place shroud back into position on the two
bottom screws. See Figure 16.
Figure 14
Increment
Weights
NG
O
WR
CT
RE
R
CO
Figure 15
Screw
Figure 16
Assembly
Page 4-5
Cybex Eagle 11030 Row Owner’s Manual
B. Install the top two screws securing the back shroud.
See Figure 17.
C. Install the three Phillips head screws securing the top
(back) shroud. See Figure 18.
9. Install weight plate decals.
Screw
NOTE: You have the option to use pounds, kilograms or both.
A. Slowly and carefully peel off back side of decal. See
Figure 19. NOTE: When peeling off back cover, make
sure that the decals remain attached to the front sticker.
Figure 17
B. Align holes in decal with appropriate holes in weight
stack. NOTE: Do not allow the adhesive to touch weight
stack at this time.
C. Insert a guide pin through each hole of the template.
NOTE: A guide pin can be anything that fits through the
weight stack hole, such as a weight stack selector pin.
D. Carefully align decal and rub it onto weight plates.
Phillips Head
Screw (3)
Figure 18
E. Carefully remove front side, leaving decals adhering to
weight plates. See Figure 20.
Front
NOTE: It is important that you perform regular inspection and
maintenance activities on your equipment. See the
CYBEX Eagle Owner’s Manual for inspection and
maintenance activities. If you do not have a CYBEX
Eagle Owner’s Manual or if you have any questions
or concerns, call CYBEX Customer Relations at
888-462-9239.
Back
Figure 19
10. Verify proper operation
11. Anchor machine to the floor.
Guide Rod
A. Securely anchor machine to the floor using the anchor
holes provided in each machine.
9.0
20
80
NOTE: Cybex is not responsible for the actual anchoring of
equipment. Consult with a professional contractor.
Weight Stack
100
120
140
160
180
200
NOTE: Use fasteners having a minimum of 500 lbs. tensile
capacity (3/8” grade 2 bolts or better).
220
240
260
280
300
320
NOTE: If legs/frame does not contact surface, DO NOT pull
down with anchors. Shim any leg or frame not in contact
with surface using flat washers.
340
360
380
400
36.0
45.0
54.0
63.0
72.0
81.0
90.0
99.0
108.0
117.0
126.0
135.0
144.0
153.0
162.0
171.0
180.0
Kilograms
Pounds
Figure 20
Assembly
Page 4-6
18.0
40
60
Cybex Eagle 11030 Row Owner’s Manual
Chapter 5 - Maintenance
All preventive maintenance activities must be performed on a regular basis. Performing
routine preventive maintenance actions can aid in providing safe, trouble-free operation of all Cybex
Strength Systems equipment.
NOTE:
Cybex is not responsible for performing regular inspection and maintenance actions
for your machines. Instruct all personnel in equipment inspection and maintenance
actions and also in accident reporting/recording. Cybex phone representatives are
available to answer any questions or concerns that you may have.
NOTE: All inspections and
repairs must be
performed by trained
service personnel only.
Cybex will void warranty if
non-Cybex replacement parts
are used.
Daily Procedures
1. Upholstery - Wipe down all upholstery as per the recommendations listed below for light
soiling and more difficult stains.
Light Soiling
• A solution of 10% household liquid dish soap with warm water applied with a soft damp
cloth.
• If necessary, a solution of liquid cleanser and water applied with a soft bristle brush.
Wipe away the residue with a water dampened cloth.
Maintenance
Page 5-1
Cybex Eagle 11030 Row Owner’s Manual
More Difficult Stains
• Dampen a soft white cloth with a solution of 10% household bleach (sodium hypochlorite), 90%
water. Rub gently. Rinse with a water dampened cloth to remove bleach concentration.
• The same procedure can be used with full strength household bleach, if necessary.
• Allow bleach to puddle on the affected area or apply with a soaked cloth for approximately 30 minutes.
Rinse with a water dampened cloth to remove any remaining bleach concentration.
Alternative Method for Difficult Stains
• Dampen a soft white cloth with rubbing alcohol and rub gently. Rinse with a water dampened cloth to
remove any remaining rubbing alcohol concentration.
NOTE: To restore luster, a light coat of spray furniture wax can be used. Apply for 30 seconds and
follow with a light buffing using a clean white cloth.
Please Review Carefully
When using strong cleaning agents such as rubbing alcohol or bleach, it is advisable to first test in an
inconspicuous area. Other cleaning agents may contain harsh or unknown solvents and are subject to
formula changes by the product manufacturer without notice. Should you desire to use other cleaning
agents, carefully try them in an inconspicuous area to determine potential damage to the material.
Never use harsh solvents or cleaners which are intended for industrial applications. To clean stained or
soiled areas, a soft white cloth is recommended. Avoid use of paper towels.
Cleaning products may be harmful/irritating to your skin, eyes, etc. Use protective gloves and eye
protection. Do not inhale or swallow any cleaning product. Protect surrounding area/clothing from
exposure. Use in a well ventilated area. Follow all product manufacturer’s warnings. CYBEX and its
vendors cannot be held responsible for damage or injuries resulting from the use or misuse of cleaning
products.
2. Frames - Wipe down all frames using a mild solution of warm water and car wash soap. Be sure to dry
thoroughly. AVOID acid or chlorine based cleaners and also cleaners containing abrasives as these
could scratch or damage the equipment.
3. Chrome - Clean chrome tubes, first using chrome polish and then using a car wax seal. Neutral
cleaners with a pH between 5.5 and 8.5 are recommended. Be sure to dry thoroughly. AVOID acid or
chlorine based cleaners and also cleaners containing abrasives as these could scratch or damage the
equipment.
Maintenance
Page 5-2
Cybex Eagle 11030 Row Owner’s Manual
4. Guidelines for cleaning front panel:
•
Use clean soft cloths or sponges for application of cleaners and again for washing and rinsing.
•
Follow up the application with warm water rinse.
•
Don’t use abrasives or high alkaline cleaners.
•
Don’t leave cleaners on for long periods, wash immediately.
•
Don’t apply cleaners in direct sunlight or at elevated temperatures.
•
Don’t use scrapers, squeegees or razors.
•
Don’t clean with gasoline.
Compatible Cleaners and Detergents:
•
Formula 409
•
Top Job
•
Joy
•
Palmolive
•
Windex with Ammonia D
To Minimize Fine or Hairline Scratches:
Mild automotive polish applied and removed with a soft, clean cloth will help fill scratches.
Suggested Polishes:
•
Johnson Paste Wax
•
Mirror Glaze #10 Plastic Polish (by Mirror Bright Polish Co.)
•
Novus Plastics Polish #1, #2 (by Novus Inc.)
Maintenance
Page 5-3
Cybex Eagle 11030 Row Owner’s Manual
Weekly Procedures
1. Check all nuts and bolts for looseness. Tighten as required.
2. Inspect all belts (entire length) for any non-uniformity and wear.
Immediately replace belt if any of the following conditions are present:
Maintenance
Page 5-4
Cybex Eagle 11030 Row Owner’s Manual
3. Some machines use cables in addition to belts. Inspect all cables for wear or damage and proper
tension. When inspecting cables, run your fingers on the cable, paying particular attention to bends
in the cable and attachment points.
Replace all worn cables immediately. The following conditions may indicate a worn
cable:
•
A tear or crack in the cable sheath that exposes the cable. See Figure 1.
Figure 1
•
A kink in the cable. See Figure 2.
Figure 2
•
A curled sheath. See Figure 3.
Figure 3
•
“Necking”, a stretched cable sheath. See Figure 4.
Figure 4
Maintenance
Page 5-5
Cybex Eagle 11030 Row Owner’s Manual
4. Inspect bars and handles for wear, paying particular attention to tab area connecting
points.
Replace all worn handles immediately.
5. Inspect snap links for proper latching (indicates wear).
Replace all worn snap links immediately.
6. Inspect for loose or worn grips.
Replace all loose or worn grips immediately.
7. Inspect all labeling for readability. This includes instructional placards, warning and caution decals.
Replace all worn labeling immediately.
8. Inspect all weight stacks for proper alignment and operation.
Correct all improper alignment and operation issues immediately.
9. Wipe Weight Stack Guide Rods clean over entire length. Lubricate with a light coat of medium
weight automotive engine oil.
Yearly Procedures
1. Replace all belts and cables at least annually.
Maintenance
Page 5-6
Cybex Eagle 11030 Row Owner’s Manual
Environment
Static Electricity - Depending upon where you live, you may experience dry air, causing a common experience of
static electricity. This may be especially true in the winter time. You may notice a static build-up just by walking across a
carpet and then touching a metal object. The same can hold true while working out on your unit. You may experience a
shock due to the build-up of static electricity on your body and the discharge path of the unit. If you experience this type
of situation, you may want to increase the humidity to a comfortable level through the use of a humidifier.
Humidity - The unit is designed to function normally in an environment with a relative humidity range of 30% to 75%.
NOTE: Do not install or use the unit in an area of high humidity, such as in the vicinity of a steam room, sauna, indoor
pool or outdoors. Exposure to extensive water vapor, chlorine and/or bromine could adversely affect the electronics as
well as other parts of the machine.
Temperature - The unit is designed to function normally in an environment with an ambient
o
o
o
o
temperature range of 50 F (10 C) to 104 F (40 C) degrees.
Storage
Humidity - The unit can be shipped and stored in an environment with a relative humidity range of 10% to 90%.
NOTE: Do not store the unit in an area of high humidity, such as in the vicinity of a steam room, sauna, indoor pool or
outdoors. Exposure to extensive water vapor, chlorine and/or bromine could adversely affect the electronics as
well as other parts of the machine.
o
o
Temperature - The unit can be shipped and stored in an environment with an ambient temperature range of 32 F (0 C)
o
o
and 140 F (60 C) degrees.
Maintenance
Page 5-7
Cybex Eagle 11030 Row Owner’s Manual
Maintenance
Page 5-8
10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX 508-533-5183
www.cybexinternational.com • [email protected]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement