Laview LV-KH94FOLFB5-T1 4-Channel 1TB HDD Indoor/Outdoor Day Night Surveillance System and (4) HD 720P Camera 1 Bonus Channel Remote View Installation guide
PDF
Download
Document
Advertisement
Advertisement
Step 5. Configure start up wizard Select the screen resolution from the drop-down menu based on your TV/monitor's resolution. Resolution System Resolution: 1024 * 768/60HZ Check this box if you wish to see this wizard again after you reboot your system. Wizard = Start wizard when device starts? We strongly recommend that you change the default Admin password ‘12345’ for better security protection. Wizard Admin Password AKA New Admin Password New Password Confirm Select the applicable time zone, date/time format, and time. Wizard Time Zone (GMT-08:00) Pacific Time US & Canada Date Format MM-DD-YYYY System Format 09-29-2014 SystemTime 18:14:37 We recommend checking ‘Enable DHCP’ even if your DVR is not connected to the internet, this will automatically get the DVR IP address. ; Wizard NICType 10M/100M Self-adaptive Enable DHCP IPv4 Address 192.0.0.64 The wizard will show additional network information, O Whatis in the box HD-TVI Digital Video Recorder HD-TVI Analog Cameras Siamese BNC Cables 1-4,8 Camera Power Splitter Mouse Remote Control ? DVR Power Adapter Camera Power Adapter Quick Start Guide Warranty Card Security Stickers © Power LED Indicates if the DVR is powered on © status LED Indicates if the Hard Drive is working © VGA Port Connects to TV or computer monitor © Audio 1/0 Connects an extra microphone/speaker (notincluded) @ TyRx LED Indicates if the Network is active © AN Connects to your router @ video In Connects cameras via BNC cables © rs485 Connection for additional PTZ camera (not Included) © USB Port Connects to a USB mouse or flash drive ® 12V Connects the12V DC Power Supply @ HDMPort Connects to HDTV or computer monitor @ rower O Troubleshooting Power Switch Problem Solution click ‘Next’ to proceed. Wizard Server Port 8000 HTTP Port 880 RTSP Port 8554 To initialize the hard drive click the ‘Init’ box otherwise the DVR will NOT record. Wizard Capacity Status Property Type Free Space M1 465.7668 Normal RW Local 464GB No display/No | e signal/Invalid format Make sure the VGA/HDMI cable is properly connected to both the DVR and TV/monitor NOTE: A laptop cannot be used as a screen Make sure your TV/monitor is on the correct video input (e.g. HDMI1, HDMI2, etc.) Try switching to another 1080p TV/monitor and adjust the output resolution in the DVR menu On the front of the DVR check that the power LED light is on No picture/No | *Ä video Make sure the camera is completely connected to the power splitters well as the Video In plug Cannot login |e The default user name is: admin and the default password is: 12345. If you don’t remember your old password, please submit a ticket to us at www.laviewusa.com/ contact/. Çe) Ke | = Innovation That Secures O HD-TVI QUICK START GUIDE O Remote Viewing View footage on your mobile devices with our app. You can either scan the provided QR code or search LaView Net in the app store. ul # Download on the [m] [m] | App Store i ANDROID APP ON >> Google play Camera e Make sure the camera is not placed behind a window, there is no interference or a strong picture is not light source in front of the camera clear e In DVR Menu>Record>P: ter>Resolution, set the sub stream resolution to CIF for LaView NET SCAN ME all channels e Move the camera to a different location and/or direction NOTE: The live view (sub stream) resolution is NOT the actual image quality recorded (Main stream); Connection of excessive length (over 200ft) of BNC cable will drop the camera image quality; Working at extreme weather condition (below -40F or above 140F) will drop the image quality and damage the camera. click ‘Next’ to proceed. Wizard IP Address Amount Model M1 192.168.1.36 1 CMIP3412 Content may vary by model, including the number of channels, cameras, configuration, and hard drive capacity. O Questions? Night visionis | e The infrared activates automatically when the environment is dark enough. You can check not working that the camera infrared bulbs are working properly as they turn light red in dark Choose continuous or motion detection recording from the listed environments options. Check the 'Start Recording’ box to initialize recording. DVR is not e Check that the hard drive status is normal and is initialized under the Main Call us at: 626-898-4988 (M-F from 9am to 6pm PST) Menu>HDD>General Enable the record mode (Normal or Motion Detection) under the Main Menu>Record>Schedule>Edit for the selected camera Open support ticket at: www.laviewusa.com/contact Tutorial videos 8%: user manual at: www.laviewusa.com/support recording Click ‘Ok’ to finish the wizard. Wizard WM Start Recording O continuous Motion Detetction Copyright O LaView Eagle-Eye Technology Inc. 2015 QUICK START GUIDE www.laviewusa.com We recommend testing all the cameras and cables prior to installation. Step 1. Connect your cameras BNC Cable Wireless Router * Connect the BNC plug and power plug of the siamese cable into the camera - Connect the opposite BNC plug into the DVR VIDEO IN port and the power plug into the camera power splitter (Repeat for all cameras) * Connect the power splitter into camera power supply HD-TVI Cameras Not Included Step 2. Connect to your monitor/TV - Connect your DVR and TV/monitor with a HDMI or VGA cable (Not included) Camera Power Splitter Note: Your monitor/TV must support the output resolution of the DVR or you may get a black screen or a possible error message. You cannot use a laptop as a display. Camera Power Step 3. Connect the mouse and power Adapter a DVR Power Adapter + Connect the mouse to the USB port * Connect the 12V DVR power adapter to the DVR VGA Step 4. Connect to your network (OPTIONAL) 000000 000000 © \ oa | - Connect the LAN port on the DVR to the LAN port on your router via an Ethernet cable for remote viewing on your mobile phone, tablets, PC and Mac HDTV | | Mouse Р 1080 PC Monitor Note: The DVR will still work as a standalone video recorder if you do not have internet connection and skip this step. Step 5. Configure the start up wizard * The connection is now completed. Turn on the power switch and follow the start-up wizard on your screen to confirgure the DVR. (next page) ">

Public link updated
The public link to your chat has been updated.
Advertisement