advertisement
NORM ENERJI
AUTOMATION TYPE BATTERY CHARGER TECHNICAL SPECIFICATIONS
GENERAL
Model / Power
Topology
Control
INPUT
Input Isolation Transformer
Nominal Voltage and Tolerance
Input Wiring
Nominal Frequency
THDI
Cosφ
Input Protection
OUTPUT
Battery Charging Principle
Rated Power
Nominal Output Voltage
Output Voltage Adjustment
Nominal Output Current
Output Current Adjustment
Static Tolerance
Output Voltage Ripple RMS
Efficiency at full load
Boost voltage (V/C)
Float voltage (V/C)
Dynamic Response (w/out battery group)
Dynamic Response (with battery group)
Output Protection
Filtering
CONTROL ELEMENTS
Battery Test
Boost Timer
Current Limitation
RDAT 220‐100 / 22.000 W
6 Pulse / Full Bridge Phase Angle Controlled Thyristor Module Rectifier
Microprocessor Controlled System
Galvanically isolated / Primary & Secondary Earth Screened
380VAC ±15%
3 Phase 3 Wires
50Hz ±5%
<35% with 6 pulse
0.8 with 6 pulse
Thermic Magnetic Overcurrent protection via MCB and Overvoltage / Undervoltage protection
Constant Current/ Constant Voltage
22.000 W
220VDC
220VDC system between 220VDC and 300VDC
100 A
0‐100% of Nominal Output Current
<1% with 6 pulse
1% RMS AC of Output Voltage with 6 pulse
>90%
2,4 lead acid battery 1,60 NiCd Battery (Depends on battery manufacturer recommendation)
2,23 lead acid battery 1,40 NiCd battery (Depends on battery manufacturer recommendation)
±10% of Output Voltage at 200msec (100% load change)
±2% of Output Voltage at 200msec (100% load change)
Short Circuit, NH Fuse and Overvoltage / Undervoltage protection
L‐C Filter
Automatic or manual selectable. Please refer to user manual for details
0 – 99,9 hours adjustable by 1 minute accuracy
Total output current and battery current can be adjusted separately
ALARM CONTACTS
Open or closed free alarm contacts
Line MCB OFF / Mains Failure , Battery MCB OFF, Load MCB OFF, low battery failure, over output voltage, charger failure, over temperature, and earth fault
DISPLAY PANEL & MEASUREMENT
Measurements
Indicators
Adjustable Parameters
Event History
LCD Display for Load Output Voltage, Rectifier Total Output Current , Battery Output Voltage / Current and Line Voltage / Frequency
Float mode, Boost mode, Current mode, Equalize mode, Battery ending, Low battery, Battery test failure, Line MCB OFF, Fan failure, Over voltage,
Under voltage, Over temperature, Rectifier failure, Mains ON (LED indication), Load MCB (LED indication), Battery MCB (LED indication), Earth Fault (
+ / ‐)
Boost charge voltage, Float charge voltage, Low battery voltage , Battery test , Charger output current, Battery charge current, Battery automatic boost current and float current, Auto & Manual boost selection, Manual boost time, LED test and On ‐ OFF.
Line MCB ON / OFF, Battery MCB ON / OFF, Load MCB ON / OFF, AC Line Input High / Low / Normal , Low Battery, Battery OK, Rectifier Overvoltage
/ Undervoltage / OK, Overtemperature / Normal Temperature, Battery Test Fail / OK events are displayed on time base. Last 250 events recorded and displayed on front panel and on PC via RS 485
On Warning Messages 2 Short ‘beep’ per 2 seconds Sound Alarm
COMMUNICATION AND PARALLELING (OPTIONAL)
Communication
Paralleling
Modbus, TCP/IP, Profibus and SNMP Communications via RS485 port ‐ EXCLUDED
Active or Passive Load Sharing available on request ‐ EXCLUDED
LVD (OPTIONAL)
LVD
DROPPER DIODES (OPTIONAL)
Dropper Diodes
Protection of Battery from Deep Discharge via Contactor. Available on request ‐ EXCLUDED
Dropper Diodes for Float and Boost Voltage Regulations. Available on request ‐ EXCLUDED
NORM ENERJI
SAFETY & ENVIRONMENT
Circuit Breakers
Over Voltage Protection
Electrical Interference Reduction
Electrical Standards
Protection Level / Color
Isolation Voltage
MTBF
Enclosure Material
Cooling
Cable Entry
Distribution
Heater & Lightning
Operating Temperature
Relative humidity
Operating Altitude
Noise Level
Cabin Dimension
BATTERY CHARGER TECHNICAL SPECIFICATIONS
Input: Miniatur circuit breakers; Output: NH Fuse ; Battery: NH Fuse
IEEE 587 4500 A, 110 Joules (standard)
FCC Part 15 Class B
EN 50091‐1 (Security) / EN 50091‐2 (EMC)
IP20 / RAL7035 as standard)
2000VAC input/chassis and output/chassis
100,000 hrs. (w/out battery group)
Mild Steel, Zinc‐phosphate coated; 100 µm electrostatic paint; 1.5 mm thickness
Forced fans
Bottom
Available on request ‐ EXCLUDED
Available on request ‐EXCLUDED
‐10 / +40 °C
5 ‐ 90 %
Max. 2000 Mt.
Max. 60 db
(H)1950 (W)650 (D)700mm (For both RDAT 220‐100 & RDAT 48‐40
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement