NA788 ENG IM Y 130819
NA788
Car Audio System Player
INSTRUCTION MANUAL
CD MP3 WMA USB SD
AUX-IN BT iPod/iPhone
USB 1A Smart Phone Battery Charge
Safety
To prevent deterioration, do not touch the terminals of the unit and
faceplate with your fingers.
WARNING
Stop the car before operating the unit.
How to reset your unit
Important to know...
To prevent a short circuit, never put or leave any metallic objects
(such as coins or metal tools) inside the unit.
Caution: Adjust the volume so that you can hear sounds
outside the car. Driving with the volume too high may cause an
accident.
Condensation: When the car is air-conditioned, moisture may
collect on the laser lens. This may cause disc read errors. In this case,
remove the disc and wait for the moisture to evaporate.
The illustrations in this manual are examples used to explain more
clearly how the controls are used. Therefore, what appears on the
illustrations may differ from what appears on the actual
equipment.
1
2
Reset
If this unit fails to operate properly, press the reset button.
The unit returns to factory settings when the reset button is pressed.
If you experience problems during installation, consult your
Nakamichi dealer.
When you purchase external components, check with your
Nakamichi dealer to make sure that they work with your model and Check and identify the contents of your package:
in your area.
What’s in the box
Maintenance
Cleaning the unit: Wipe off the dirt on the panel with a dry silicon or
soft cloth. Failure to observe this precaution may result in damage to
the monitor or unit.
Cleaning the connector: Wipe off dirt on the connector of the unit and
faceplate. Use a cotton swab or cloth.
Main unit
(with sleeve)
Front panel
Trim plate
Remote
control
ISO male
connector
Screw x 4pcs
Hexagon head
screw
Rubber cushion
User manual
Preparation
How to attach/detach the faceplate
Attach
Detach
1
1
2
2
Do not expose the faceplate to direct sunlight, excessive heat, or
humidity. Also avoid places with too much dust or the possibility of
water splashing.
Keep the faceplate in its casing while detached.
The faceplate is a precision piece of equipment and can be
damaged by shocks or jolts.
2 EN
Installation / Connection
Caution
Basic Procedure
1 Remove the key from the ignition switch, then disconnect
the terminal of the car battery.
2 Make proper input and output wire connections.
3 Install the unit to your car.
4 Reconnect the
terminal of the car battery.
5 Reset the unit.
Warning
The unit can only be installed in a car with a 12 V DC power supply, negative
ground.
If you connect the ignition wire (red) and the battery wire (yellow) to the car
chassis (ground), you may cause a short circuit, that in turn may start a fire.
Always connect those wires to the power source running through the fuse box.
Disconnect the battery’s negative terminal and make all electrical
connections before installing the unit.
Insulate unconnected wires with vinyl tape or other similar material. To
prevent a short circuit, do not remove the caps on the ends of the
unconnected wires or the terminals.
Be sure to ground this unit to the car’s chassis again after installation.
If the power is not turned ON, the speaker wire may have a short-circuit or
touched the chassis of the vehicle and the protection function may have
been activated. Therefore, the speaker wire should be checked.
If your car’s ignition does not have an ACC position, connect the ignition
wires to a power source that can be turned on and off with the ignition key. If
you connect the ignition wire to a power source with a constant voltage
supply, as with battery wires, the battery may die.
Install this unit in the console of your vehicle. Make sure the faceplate will
not hit the lid of the console (if any) when closing and opening.
After the unit is installed, check whether the brake lamps, blinkers, wipers,
etc. on the car are working properly.
Mount the unit so that the mounting angle is 30° or less.
If the fuse blows, first make sure the wires are not touching to cause a short
circuit, then replace the old fuse with one that has the same rating.
Connect the speaker wires correctly to the terminals to which they
correspond. The unit may be damaged or fail to work if you share
the
wires or ground them to any metal part in the car.
When only two speakers are being connected to the system, connect the
connectors either to both the front output terminals or to both the rear
output terminals (do not mix front and rear).
Mounting and wiring this product requires skills and experience. For
safety’s sake, leave this work to professionals.
If you experience problems during installation, consult your Nakamichi
dealer.
Wiring Connection
Bluetooth External Microphone
OE Steering learning Remote
SUB OUT
OE external remote (Purple)
ISO Connector
OE remote adapter
(not supplied)
Antenna Jack(not included)
Subwoofer Output
1
2
B
3
4
5
6
5
A
(White)
(Gray-GND)
(White)
Steering wheel
remote
4
7
8
Rear RCA Output (Left)
Front RCA Output (Left)
Rear RCA Output (Right)
Front RCA Output (Right)
7
8
ISO Connector Wiring Chart
Pin
Color and function
A4
Yellow
A5
Blue
A7
A8
Red
Black
Pin
Color and function
B1/B2
Connect to system control terminal B3/B4
Violet + / Violet/Black
Grey + / Grey/Black
Right rear speaker
Right front speaker
B5/B6
B7/B8
White + / White/Black
Green + / Green/Black
Left front speaker
Left rear speaker
Battery(+)
of the power AMP or auto antenna
relaycontrol terminal(Max 150MA 12VDC)
Ignition(ACC)
Ground
EN 3
Installing the unit
Installation with the half sleeve
After inserting the half sleeve into the dashboard, select the appropriate tab according to the thickness of the dashboard material
and bend them inwards to secure the holder in place.
18
Bend the appropriate
tabs to hold the sleeve
firmly in place.
2
mm
112
m
m
1
Dashboard
Screw
2
3
Control panel
Installation using the screw holes on the side of the unit
Select a position where the screw holes of the bracket and the screw holes of the main unit become aligned (are fitted) and tighten
the screws at 2 places on each side.
All the mounting sleeve & screw are not included in this packing.
4 EN
Basic Operation
Detaches the control panel
Ejects the disc
USB socket
Open the cover
OK / Mute
Encoder Volume Knob
1A battery charge USB socket
Open the cover
Aux-In jack
When you press or hold the following button(s)...
Main unit
General operation
Switch music listening zone for the best speaker sound. (FRONT ALL / FRONT LEFT/ FRONT RIGHT / ZONE OFF).
■ To adjust the EQ (Preset Equalizer) setting.
■ Turn On or Off the Xbass bosster function.
■ To turn On or Off dynamic bass boost sound.
■ Press and hold to enter into iPod/iPhone control mode.
■ To access into the Audio Menu mode.
■ press and hold to enter into the System Menu mode.
■ Under Media playback mode to view play informations.
■ Under RDS mode to view RDS received information.
■ Press and hold turn On or Off the subwoofer function.
■ Under Radio mode to enter into the Auto Seek mode, press and hold to enter into the Manual Seek mode.
■ Under Media playback mode to skip track / file, press and hold to fast forward / backward.
■ Turn the unit on. Press and hold again to turn the unit off.
■
■
OK / Mute
Rotatory
Volume knob
■
■
■
■
■
■
■
■
■
■
■
Select the available sources (Radio, Disc, USB (USB-iPod/iPhone), SD, BT AUDIO or Aux-In ), if the power is turned on.
Turn mute or restore volume.
Confirms selection.
Rotate it to increase or decrease the volume.
Select items.
Select the FM bands (FM1/ FM2/ FM3) or AM1 (MW1) / AM2 (MW2) .
Under media playback to access into search mode.
To answer / accept the call.
During the talking, press and hold to transfer the call.
To reject / end the call.
Returns to the previous item.
Press and hold access into the VRD display color setting mode.
Pause/resume playback of a Disc, USB / SD device, iPod/iPhone.
EN 5
Remote Control Operation
SRC
AUDIO
When you press or hold the following button(s)...
Main unit
General operation
Turn mute or restore volume.
Press turn the unit on or off.
Press increase the volume.
Press decrease the volume.
■
■
SRC
AUDIO
6 EN
Under Radio mode to enter into the Auto Seek mode, press and hold to enter into the Manual Seek
mode.
Under Media playback mode to skip track / file, press and hold to fast forward / backward.
Selects the available sources (Radio, Disc, USB (USB-iPod/iPhone), SD, BT AUDIO or Aux-In ), if the
power is turned on.
Press to access into the Audio Menu mode.
Function Settings
1 Press
to access into the [AUDIO MENU] mode, press and hold to enter into the [MENU] mode.
2 Press
repeatedly to select the item to be adjusted.
3 Turn the encoder volume knob to select a value / option.
[AUDIO MENU]...
Item
BASS ADJUST
BASS LEVEL
MIDDLE ADJUST
MIDDLE LEVEL
TREBLE ADJUST
TREBLE LEVEL
BALANCE
FADER
SUBWOOFER ADJUST
SUBWOOFER LEVEL
SUBWOOFER LPF
RESUME
Selectable Setting
Adjust the level -7 to +7.
Adjust the level -7 to +7.
Adjust the level -7 to +7.
Adjust the balance between the right and left speakers from 12R (full right) to 12L (full left).
Adjust the fader between the front and rear speakers from 12R (full rear) to 12F (full front).
Adjust the level 0 to 12.
Subwoofer low pass filter range: 80 / 120 / 160.
Resume the preset EQ value to factory default value.
[MENU]...
Item
CLOCK
CLOCK SET
CLOCK FORMAT
BEEP TONE
DEMO
SWC SET
RGB COLOR
Selectable Setting
Adjust the Hours and Minutes
Select the time format 12H or 24H
Turn On or Off this beep sound
To automatically demo this unit’s major features cyclic on LCD display.
If you car is equipped with the steering wheel remote controller, you can operate this unit using
the controller.
■ Press the “OK / Mute” to access into SWC SET mode.
■ Rotate encoder volume knob to select the function you want the steering remote to learn, then press
and hold the same function button on the steering wheel remote until “SUCCEED” is displayed.
This unit is equipped with variable color display. Once into the RGB COLOR mode, rotating
encoder volue knob to selected the LCD color.
■ COLOR SCAN (default setting); WHITE; GREEN 1; GREEN 2; GREEN 3; AMBER; PINK 1; PINK 2;
PURPLE 1; PURPLE 2; BLUE 1; BLUE 2; ORANGE; USER COLOR; SCAN.
[ZONE]...
This innovative Zone technology enables driver or passengers to enjoy music with the best speakers balance and
experience a more vivid spacial effect as the artist is intended to create. User can switch the music listening zone
from driver to passengers for the best speaker sound settings in car.
1 Press the ZONE button,The current setting is displayed.
2 Press the ZONE repeatedly to select one of the below setting:
• FRONT ALL ( All)
• FRONT LEFT ( Left)
• FRONT RIGHT(Right)
• ZONE OFF (Off )
EN 7
Listening to the Radio
Hold for about 2 seconds to
memorize the current station.
■ Press briefly to recall
memorized station.
■
In receive tracffic, press to cancel receive the current traffic.
1 Press
repeatedly to a band ( FM1, FM2, FM3,
AM1(MW1) or AM2 (MW2) ).
2 Press
to search for a station.
3 Press
repeatedly to view RDS received information.
Adjust [MENU] mode settings
While listening to the radio...
1 Press and hold
2 Press
to enter into the [MENU] mode.
repeatedly to select the item to be adjusted.
3 Turn the encoder volume knob to select a value / option.
Item
Selectable Setting
Press the “OK / Mute” to access into Auto Store mode, the six strongest stations of the selected band
AUTO STORE
are saved in preset channel automatically: FM1, FM2, FM3(1-6), AM1, AM2.
Once into the PTY mode, press the “OK / Mute” get into program type item, and rotating encoder
volume knob to selected category.
■ Available Program Type:
PTY
POP M; ROCK M; EASY M; LIGHT M; CLASSICS; OTHER M; JAZZ M; COUNTRY; NATION M; OLDIES M;
(Program Type)
FOLK M; A-TEST; ALARM; NEWS; AFFAIRS; INFO; SPORT; EDUCATE; DRAMA; CULTURE; SCIENCE;
VARIED; WEATHER; FINANCE; CHILDREN; SOCIAL; RELIGION; PHONE IN; TRAVEL; LEISURE;
DOCUMENT
■ ON: The unit will be searches for another station with stronger signal, but with the same program
AF
identification as the current station automatically.
(Alternate Frequencies) ■ OFF: Cancel
■ ON: When there is traffic announcement, the unit switches to the tuner mode (regardless of the
TA
current mode) and begins to broadcast the announcemet on traffic conditions. When the
(Traffic Announcement)
trafficannouncement is over, it returns to the previous mode.
■ OFF: Traffic announcement does not cut in.
Turn On or Off the RDS function.
RDS On/Off
Select suitable country region of the radio: USA; LATIN; EUROPE; RUSSIA(Oirt); M-EAST; ASIA; JAPAN;
AREA
AUST (Australia)
To receive more radio stations or only stations with strong signal, you can adjust the radio
LOCAL SEEK
sensitivity.
8 EN
Listening to a Disc/ USB/SD device
Press to pause. Press again to resume playback.
Press to repeat one track, press again to repeat all tracks.
■ Press and hold repeat a folder.
■
■
■
Press to start random play, press again to cancel random play.
Press and hold random a folder.
Press to move next/previous folder.
■
■
Press into search mode
Press to select a track / file.
Press and hold for fast forward / backward.
Playing a disc
USB Smart Phone 1A charging
Insert the disc into the Disc Slot with label side facing up,
Press the “SRC”button to select the Disc mode to start playing.
1 Open the cover marked ”
“ on the front panel.
2 Insert the iPhone/Smart Phone device into the USB socket.
3 Once the iPhone/Smart Phone is connected and recognized,
the iPhone/Smart Phone begins to charge.
Playing a USB device
1 Open the cover marked
on the front panel.
2 Insert the USB device into the USB socket.
3 Press the “SRC” button to select the USB mode to start playing.
Remark:
Remark:
This USB is compatible with iPhone / iPod, USB stick, and play the
songs in some Hand phone & recharge them. ( Subject to the brand &
model of the Hand phone )
This USB only can charge Phones, but cannot play or decode music files.
Listening to the other external components
Playing a SD memory card
1 Press the Panel
(Release) button.
2 Push the left side of the panel rightward
3 Insert the card into the card slot.
4 Close the front panel.
5 Press the “SRC” button to select the SD mode to start playing.
Auxiliary input jack
3.5 mm Cable
(not included)
1 Press the SRC to select AUX-IN mode.
2 Turn on the external component and start playing.
EN 9
Listening to the iPod / iPhone
Press to pause. Press again to resume playback.
Press to repeat one track, press again to repeat all tracks.
■ Press and hold repeat a folder.
■
■
■
Press to start random play, press again to cancel random play.
Press and hold random a folder.
Press to move next/previous folder.
■
■
Press into search mode
Press to select a track / file.
Press and hold for fast forward / backward.
Playing a iPod / iPhone
1 Open the cover marked
on the front panel.
2 Insert the USB adaptor on one end of iPod/iPhone cable into
the USB socket.
3 Press the “SRC” button to select the USB-iPod/iPhone mode to
start playing.
Search for music on iPod / iPhone
1 Press
on front panel to switch the iPod/iPhoe control mode.
2 Use the iPod / iPhone to search / operates music control.
Remark:
Please make sure the iPod / iPhone cable is connected correctly.
And please only use original iPod / iPhone cable (not supplied) .
Compatible iPod/iPhone
Apple iPod and iPhone models with a 30-pin dock connector:
- iPod nano (2nd generation)
- iPod nano (3rd generation, 4GB only)
- iPod nano (3rd generation, 8GB only)
- iPod nano (4th generation)
iPod/iPhone Cable (not included)
- iPod nano (5th generation)
- iPod classic (1st generation)
Search for music on unit
- iPod classic (2nd generation)
- iPod touch (1st generation)
1 Press
to browse iPod/iPhone menu.
2 Roate Encoder Volume knob to select the Artist search mode, - iPod touch (2nd generation)
- iPod touch (3rd generation)
and press “OK / Mute” to confirm.
- iPod video (30GB, 80GB only)
3 Press
to search alphabetically.
4 Roate Encoder Volume knob to select the Album, then press - iPhone
- iPhone 3G
“OK / Mute” to confirm.
5 Roate Encoder Volume knob to select desired song in the - iPhone 3GS
- iPhone 4
current album, press “OK / Mute” to confirm start play.
- iPhone 4S
Remark:
- iPhone 5
To go back to upper level of a folder, press
.
10 EN
Operation of Bluetooth Hands-Free
Press to answer / accept the call.
Press and hold to transfer the call.
Press to reject / end the call.
■
■
Press to change to “BT AUDIO" mode.
You can make or receive phone calls with Bluetooth-enabled To redial number
phones through the unit. You can also listen to music from a 1 Press
on front panel to redial.
Bluetooth-enabled device.
2 Press
once again , unit will display [CALLING], and the
unit starts dialing the number dialed last time.
Getting Started
Before use the Bluetooth device, you need to pair the device to Remark:
To make an outgoing call on this unit, the bluetooth
the unit. Pairing needs only to be done once.
connection between the unit and the phone must be active.
Pairing the Bluetooth devices
1 Open your mobile phone and switch bluetooth on.
Receiving a Call
2 Search for other bluetooth device with your device.
1 If there is incoming call, the phone number is displayed. if the
incoming call has no phone number, [PHONE IN] is displayed.
3 Select “NAKAMICHI” in the pairing list.
4 Input the password “0000”
2 Press
to answer / accept the call.
5 [Pairing OK] will be displayed on the screen if pairing is
to terminate the call.
successful, and the paired device will connect to the car audio 3 When conversation ends, press
system automatically.
Disconnect the bluetooth
Call Transfer
You can transfer voice from loudspeaker to mobile phones during
1 Press and hold
to enter into the [MENU] mode.
call.
2 Once the [ DISCONN ] is displayed, press “OK / Mute” to During talking, press and hold
voice transfers from
activate the manual Disconnect mode.
loudspeaker to mobile phone.
Re-connect the bluetooth
Bluetooth Audio Streaming A2DP
1 Press and hold
to enter into the [MENU] mode.
2 Once the [BT CONNECT] is displayed, press “OK / Mute” to If the connected Bluetooth device supports Advanced Audio
Distribution Profile (A2DP), you can listen to the music stored on
activate the manual Re-connect mode.
the device through the unit. If the device also supports Audio
Video Remote Control Profile (AVRCP) profile, you can use the
control on the unit or its remote control to play music stored on
Making a Call
the device.
You can dial number through the mobile phone.
1 Press SRC repeatedly to select [BT AUDIO].
1 Use the Mobile Phone to dial and make an outgoing call.
2 Press
to start play, press it again to pause.
2 Once completed the dialing, [CALLING] is displayed.
3 To track up/down, press
/
.
EN 11
Product Information
General
Power Supply: 12V DC (10.5-14.4V), negative ground
Fuse: 15A
Suitable Speaker Impedance: 4 -8
Aux-In level: 800mV
Audio Section
Maximum Power Output: Mosfet 50W x 4 Channels
Continous Power Output: 24W x 4 RMS
Pre-AMP Output Voltage: 4 V
Subwoofer Output Voltage: 3 V
Bluetooth
Output power: Class 2
Frequency band: 2.4000GHz-2.4835GHz ISM Band
Range:
3 meters (free space)
Standard:
Bluetooth 2.0 specification
About Audio file
■
■
■
■
■
FM tuner section
Frequency Range: 87.5 - 108MHz
Usable Sensitivity: Better than 15dB at S/N 30dB
AM tuner section
Frequency Range: 522 - 1620KHz
Usable Sensitivity: Better than 45dB at S/N 26dB
USB devices
USB Flash Memory: USB 1.1 & 2.0 Compatible
Memory Card
Support type of memory card: SD/SDHC
12 EN
USB or memory file system: FAT16, FAT32
MP3/WMA bit rate: 32-320kbps and varible bit rate
MP3 sampling frequencies: 8-48kHz
WMA sampling frequencies: 32kHz, 44.1kHz, 48kHz
ID3 tag v1.0 or later
USB Smart Phone 1A charging
Output Voltage : 5 V DC
Output Current : 1000 mA (1A)
www.nakamichicaraudio.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising