AV Surround Sound Receiver - Luxusní

AV Surround Sound Receiver - Luxusní
SVENSKA
NEDERLANDS
DEUTSCH
ITALIANO
PORTUGUÊS
ESPAÑOL
FRANÇAIS
AV Surround Sound Receiver
ENGLISH
T 748
РУССКИЙ
®
Owner’s Manual
IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN
AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER
TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE”
WITHIN THE PRODUCT’S ENCLOSURE THAT MAYBE OF
SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC
SHOCK TO PERSONS.
NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV system installer’s attention to Section
820-40 of the NEC which provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as practical.
FRANÇAIS
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS
INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT
OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN
THE LITERATURE ACCOMPANYING THE APPLIANCE.
ESPAÑOL
PORTUGUÊS
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.
SAVE THESE INSTRUCTIONS FOR LATER USE. FOLLOW ALL
WARNINGS AND INSTRUCTIONS MARKED ON THE EQUIPMENT.
ITALIANO
1
2
3
4
5
6
7
DEUTSCH
NEDERLANDS
SVENSKA
РУССКИЙ
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any of the ventilation openings. Install in accordance with
the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized or grounding type
plug. A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong is provided for your safety. When the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10 Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
11 Only use the attachments/accessories specified by the manufacturer.
12
Use only with a cart, stand, tripod, bracket, or table specified
by the manufacturer, or sold with the apparatus. When a
cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13 Unplug this apparatus during lightning storms or when unused for long
periods of time.
14 Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power
supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
2
FCC NOTICE
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates uses and can radiate radio frequency energy
and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the
following measures
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION
These servicing instructions are for use by qualified service personnel only. To
reduce the risk of electric shock, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so.
INFORMATION ABOUT COLLECTION AND DISPOSAL OF
WASTE BATTERIES (DIRECTIVE 2006/66/EC OF THE EUROPEAN
PARLIAMENT AND THE COUNCIL OF EUROPEAN UNION) (FOR
EUROPEAN CUSTOMERS ONLY)
Batteries bearing any of these symbols indicate
that they should be treated as “separate collection”
and not as municipal waste. It is encouraged that
necessary measures are implemented to maximize
the separate collection of waste batteries and
to minimize the disposal of batteries as mixed
municipal waste.
ATTENTION
Disconnect this apparatus from the AC mains completely by unplugging
the power cord plug from the AC receptacle.
CAUTION REGARDING PLACEMENT
To maintain proper ventilation, be sure to leave a space around the unit
(from the largest outer dimensions including projections) that is equal to or
greater than shown below.
Left and Right Panels: 10 cm
Rear Panel: 10 cm
Top Panel: 20 cm
ITALIANO
End-users are exhorted not to dispose waste
batteries as unsorted municipal waste. In order to
achieve a high level of recycling waste batteries,
discard waste batteries separately and properly through an accessible
collection point in your vicinity. For more information about collection and
recycling of waste batteries, please contact your local municipality, your
waste disposal service or the point of sale where you purchased the items.
DEUTSCH
By ensuring compliance and conformance to proper disposal of waste
batteries, potential hazardous effects on human health is prevented and
the negative impact of batteries and waste batteries on the environment
is minimized, thus contributing to the protection, preservation and quality
improvement of the environment.
NOTE: THE T 748 IS NOT AN AUTO VOLTAGE UNIT. CONNECT ONLY
TO THE PRESCRIBED AC OUTLET, I.E., 120V 60HZ OR 230V 50HZ.
RECORD YOUR MODEL NUMBER (NOW, WHILE YOU CAN SEE IT)
The model and serial number of your new T 748 are located on the back of
the cabinet. For your future convenience, we suggest that you record these
numbers here:
Model no:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Serial no.: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
РУССКИЙ
SVENSKA
ESPAÑOL
The materials can be reused in accordance with their markings. Through
re-use, recycling of raw materials or other forms of recycling of old
products, you are making an important contribution to the protection of
our environment. Your local administrative office can advise you of the
responsible waste disposal point.
PORTUGUÊS
CAUTION
Changes or modifications to this equipment not expressly approved by
NAD Electronics for compliance could void the user’s authority to operate
this equipment.
FRANÇAIS
NOTES ON ENVIRONMENTAL PROTECTION
At the end of its useful life, this product must not be disposed
of with regular household waste but must be returned to a
collection point for the recycling of electrical and electronic
equipment. The symbol on the product, user’s manual and
packaging, point this out.
NEDERLANDS
WARNING!
The unit must not be exposed to dripping or splashing liquids, and liquidfilled objects such as vases or cups should not be placed on the unit.
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
NAD is a trademark of NAD Electronics International, a division of Lenbrook Industries Limited
Copyright 2011, NAD Electronics International, a division of Lenbrook Industries Limited
3
INTRODUCTION
TABLE OF CONTENTS
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . 2
INTRODUCTION
FRANÇAIS
GETTING STARTED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
WHAT’S IN THE BOX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
INITIAL SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
CHOOSING A LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
DEFAULT SOURCE SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
IDENTIFICATION OF CONTROLS
FRONT PANEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
REAR PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
AVR 4 REMOTE CONTROL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
USING THE AVR 4 REMOTE CONTROL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
LIBRARY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
ESPAÑOL
OPERATION
PORTUGUÊS
ITALIANO
USING THE T 748 - MAIN MENU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
ABOUT THE ON-SCREEN DISPLAY (OSD). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
MAIN MENU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
LISTENING MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
ADJUSTING LISTENING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
DSP OPTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
TONE CONTROLS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
USING THE T 748 – SETUP MENU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
SETUP MENU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
SOURCE SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
SOURCE SETUP (NORMAL). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
SOURCE SETUP (TABLE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
iPod SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
SPEAKER SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
AUTO CALIBRATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
SPEAKER CONFIGURATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
SPEAKER LEVELS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
SPEAKER DISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
ADJUSTING THE VOLUME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
AMPLIFIER SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
HDMI SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
LISTENING MODE SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
LISTENING MODES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
DOLBY DIGITAL SURROUND MODES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
DOLBY SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
DTS SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
DTS SURROUND MODES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
ENHANCED STEREO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
DISPLAY SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
A/V PRESETS SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
LISTENING TO AM/FM RADIO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
SELECTING A TUNER BAND. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
STORING PRESETS (AM/FM). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
CHOOSING THE TUNER MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
ABOUT USER NAMES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
ABOUT RDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
LISTENING TO DAB RADIO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
CONNECTING THE DAB MODULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
DAB OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
SERVICE LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
DAB TUNER MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
LOCAL SCAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
STATION ORDER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
DYNAMIC RANGE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
MANUAL TUNE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
PRUNE LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
DAB RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
SETTING DAB PRESETS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
DELETING A DAB PRESET. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
INFORMATION SETTINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
OPERATION
LISTENING TO YOUR iPod PLAYER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
CONNECTING THE OPTIONAL NAD IPD AND
iPod PLAYER TO THE T 748. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
CONTROL FEATURES AND SETTINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
NAD IPD 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
TO VIEW VIDEOS OR PHOTOS LOADED IN YOUR iPod. . . . . . . . . . . . . . . . 36
REFERENCE
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
DEUTSCH
NEDERLANDS
SVENSKA
THANK YOU FOR CHOOSING NAD.
The T 748 AV Surround Sound Receiver is a technologically advanced and
highly capable product yet we have invested great effort in making it simple
and easy to use. The T 748 delivers a range of genuinely useful options for
surround sound and stereo listening alike, using powerful digital signal
processing and superbly accurate digital-audio circuitry. However, we have
also been careful to ensure that the T 748 is as musically transparent, faithful
to every video detail and spatially accurate as possible, incorporating much
of what we’ve learned from over three decades of experience designing
audio, video and home-theater components. As with all our products, NAD’s
“Music First” design philosophy guided the T 748’s design, such that it can
confidently promise you both state-of-the-art surround home-theater and
audiophile-quality music listening for years to come.
We encourage you to take a few minutes now to read right through this
manual. Investing a little time here at the outset might save you a good
deal of time later, and is by far the best way to ensure that you make the
most of your investment in the T 748, and get the most from this powerful
and flexible home-theater component.
One more thing: We urge you to register your T 748 ownership on the NAD
Worldwide Web site:
http://NADelectronics.com
For warranty information contact your local distributor.
РУССКИЙ
NAD SHALL NOT BE HELD LIABLE FOR ANY TECHNICAL OR USER INTERFACE DISCREPANCIES IN THIS MANUAL.
THE T 748 OWNER’S MANUAL MAY BE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. CHECK OUT THE NAD WEBSITE FOR THE LATEST
VERSION OF THE T 748 OWNER’S MANUAL.
4
INTRODUCTION
ENGLISH
GETTING STARTED
WHAT’S IN THE BOX
FRANÇAIS
Packed with your T 748 you will find
• An AM loop antenna
• A FM ribbon-wire antenna with balun
• A detachable mains power cord
• Measurement microphone for auto calibration
• AVR 4 remote control with 2 AA batteries
• Owner’s manual in CD-ROM
ESPAÑOL
SAVE THE PACKAGING
Please save the box and all of the packaging in which your T 748 arrived. Should you move or
otherwise need to transport your T 748, this is by far the safest container in which to do so. We’ve seen
too many otherwise perfect components damaged in transit for lack of a proper shipping carton, so
please: Save that box!
INITIAL SETUP
PORTUGUÊS
Before you make the first connection to your T 748, you should have the arrangement of your
listening room/home theater components and furniture mapped out, at least initially. Unfortunately, a
discussion of the vital questions of loudspeaker placement and listening/viewing positions is beyond
our scope here.
CHOOSING A LOCATION
Choose a location that is well ventilated (with at least several inches to both sides and behind), and
that will provide a clear line of sight, within 25 feet/8 meters, between the T 748’s front panel and your
primary listening/viewing position - this will ensure reliable infrared remote control communications.
The T 748 generates a modest amount of heat, but nothing that should trouble adjacent components.
It is especially important that sufficient ventilation be provided.
ITALIANO
DEFAULT SOURCE SETTINGS
Audio Input
Video Input
Source 1
HDMI 1/ Audio 1
HDMI 1
Source 2
Optical 2/ Audio 2
Component Video 1
Source 3
Coaxial 1/Audio 3
Video 1
Source 4
Coaxial 2/Audio 3
Video 2
iPod
Audio 2
S-Video
Front
Optical Front Input/ Audio Front Input
S-Video Front Input
Media Player
Audio Front Input
NEDERLANDS
Source
DEUTSCH
The following table lists the default SOURCE settings. Note that the Audio input settings show both
digital and analog audio input. Digital input will always take precedence over analog audio input even
if both are present.
Tuner
For Video output, select the highest quality video format available on your TV/Monitor and utilize this
for your Monitor OUT connection from the T 748 to the TV/Monitor. For T 748, this should be HDMI
with the other choice being Composite video output.
РУССКИЙ
SVENSKA
To modify the above default settings and for a better understanding of source setting and
combinations, please refer to the item about “SOURCE SETUP” in the “USING THE T 748 - SETUP MENU”
segment of the “OPERATION” section.
5
IDENTIFICATION OF CONTROLS
FRONT PANEL
ENGLISH
1
2
3
4
5
6
7
8
9
FRANÇAIS
ESPAÑOL
A
PORTUGUÊS
10
ITALIANO
1 STANDBY BUTTON
• Press this button to switch ON the T 748 from standby mode. The
Standby LED indicator will turn from amber to blue and illuminate
the VFD. Pressing the STANDBY button again turns the unit back to
standby mode.
2 STANDBY LED
• This indicator will light up amber when the T 748 is at standby
mode.
• When the T 748 is powered up from standby mode, this indicator
will illuminate blue.
DEUTSCH
3 NAVIGATION and ENTER BUTTONS
The navigation [ a/s/d/f ] and [ENTER] buttons have various
applications specific to given modes. The middle round button is
designated as [ENTER] button; this is normally pressed to complete a
selection, procedure, sequence or other applicable functions.
NEDERLANDS
SVENSKA
AM/FM mode
Toggle [ENTER] button to switch between “Tune” and “Preset” mode.
Select “Tune” mode.
• Pressing momentarily the [ a/s ] buttons will manually scan the AM
or FM band.
• Press and hold [ a/s ] for more than 2 seconds to search up/
down;the T 748’s tuner will stop at the next sufficiently strong signal
it encounters.
• Note that this function “wraps” - that is, it will continue to search
from one end of the AM or FM band to the other until it stops at a
strong signal.
РУССКИЙ
Toggle [ENTER] button to switch between “Tune” and “Preset” mode.
Select “Preset” mode.
• Use [ d/f ] to step up or down AM/FM Presets. Unused presets are
skipped over. Note that Presets must have been previously stored.
Refer also to the item about STORING PRESETS (AM/FM) at the
LISTENING TO AM/FM RADIO section of the OPERATION page.
6
B
C
11
D
E
12
DAB mode (230V version model only)
• Use front panel [ a/s ] and [ENTER] buttons in combination with
[MENU] button to select through applicable DAB menu options.
4MENU
• Press to activate or deactivate OSD menu.
• At DAB mode, use the [MENU] button in combination with the front
panel [ a/s ] and [ENTER] buttons to activate DAB menu options.
5 LISTENING MODE
• Toggle to select through the various Listening mode options.
• Depending on the format of the currently selected input (digital
or analog, stereo or multichannel), various listening modes are
available.
• Refer also to the item about LISTENING MODE under the USING THE
T 748 - MAIN MENU segment of the OPERATION section.
6 VACUUM FLUORESCENT DISPLAY (VFD)
• Displays visual information about the current settings like the active
Source, volume level, listening mode, audio format, applicable RDS/
DAB as well as iPod-related display information and other related
indicators.
• Refer also to the item about DISPLAY SETUP under the USING THE
T 748 - SETUP MENU segment of the OPERATION section.
7 REMOTE SENSOR
• Point the AVR 4 remote control at the remote sensor and press the
buttons.
• Do not expose the remote sensor of the T 748 to a strong light
source such as direct sunlight or illumination. If you do so, you may
not be able to operate the T 748 with the remote control.
Distance: About 23ft (7m) from the front of the remote sensor.
Angle: About 30° in each direction of the front of the remote sensor.
IDENTIFICATION OF CONTROLS
ENGLISH
FRONT PANEL
FRANÇAIS
8 SOURCE [ 3/4 ]
• Toggle through the input selections - Source 1, Source 2, Source 3,
Source 4, iPod, Source 7, Front Input, Media Player and Tuner (AM/
FM/DAB as applicable). More Sources can be directly recalled upon
enabling them at the Setup Menu.
• Refer also to the item about SOURCE SETUP under the USING THE
T 748 - SETUP MENU segment of the OPERATION section.
9VOLUME
• The VOLUME control adjusts the overall loudness of the signal being
fed to the loudspeakers or headphones.
• Turn clockwise to increase the volume level; counter clockwise to
lower it.
PORTUGUÊS
ESPAÑOL
10PHONES
• Accepts stereo headphone using a standard 1/4-inch stereo phone
plug (use a suitable adaptor for headphones equipped with a
smaller plug).
• Plugging in headphones automatically mutes output from the
speakers.
• For headphone listening, the Front speakers must be set to “Large” at
the “Speaker Configuration” of the Speaker Setup item at the Setup
Menu; otherwise headphone bass response will be restricted.
• Plugging in headphones will automatically switch the T 748 to
Stereo or Analog Bypass modes.
DEUTSCH
ITALIANO
11 FRONT INPUT PORTS
• Use these convenience jacks for occasional sources such as a
camcorder, video game console, any analog audio or optical digital
audio sources and composite video sources.
• If your source has two output jacks indicative of stereo output,
insert both jacks into the T 748’s corresponding Front “L” (item A) and
“R (MONO)” input to achieve stereo output as well.
• On the other hand, if your source has a single audio out jack only or
is marked “Mono output”, plug this into the T 748’s Front “R (MONO)”
input (item B).
• Connect composite video output source to the front composite
video input (item C).
• Connect S-Video output source to the front S-Video input (item D).
• Use the front optical audio input (item E) for optical digital audio
sources.
РУССКИЙ
SVENSKA
NEDERLANDS
12 FRONT MP/MIC INPUT
• Connect your Media Player’s standard stereo phone jack to this
input.
• This is also same input where the supplied microphone is
connected for speaker auto calibration.
• Refer also to the item about AUTO CALIBRATION under the USING
THE T 748 - SETUP MENU segment of the OPERATION section.
7
IDENTIFICATION OF CONTROLS
REAR PANEL
ENGLISH
1
2
3
4
5
6
7
8
FRANÇAIS
ESPAÑOL
PORTUGUÊS
9
10 11
12
13
14
15
ITALIANO
ATTENTION!
Please make sure that the T 748 is powered off or unplugged from the mains power source before making any connections. It is also advisable to power
down or unplug all associated components while making or breaking any signal or AC power connections.
DEUTSCH
1 FM ANTENNA TERMINAL
• Connect the supplied lead-type FM antenna to the FM antenna
input. Extend the lead. Experiment freely with your antenna
placement and orientation until you get the clearest sound and
lowest background noise. Fix the antenna in the desired position by
using thumb tacks, push pins or any suitable means.
NEDERLANDS
AM ANTENNA TERMINAL
The AM loop antenna supplied with the T 748 (or a suitable
replacement) is required for AM reception.
• Connect the supplied AM loop antenna to these terminals. If an
external AM antenna is used, make connections to the AM and GND
terminals in accordance with the instructions supplied with the
antenna.
• Testing different positions for the antenna may improve reception;
vertical orientation will usually produce the best results. Antenna
proximity to large metal objects (appliances, radiators) may impair
reception, as will as attempts to lengthen the wire to the loop.
• Refer also to the item about ASSEMBLING THE LOOP ANTENNA at
the LISTENING TO AM/FM RADIO section of the OPERATION page.
SVENSKA
РУССКИЙ
2 AUDIO 1-2/VIDEO 1-2/S-VIDEO
• These comprise the T 748’s other sets of principal input. Connect
these S-Video, composite video, and analog audio input ports to
the corresponding output ports of source components such as DVD
players or cable/satellite boxes.
• AUDIO 2 IN and S-VIDEO IN are the assigned default ports for the
audio/video output of the separately sold NAD IPD (NAD IPD Dock
for iPod) 1, NAD IPD 2 and later variants.
8
3 MONITOR OUT
• Connect to the video input of a monitor/television using quality
dual-RCA cables designed for video signals.
4 COMPONENT VIDEO INPUT
• Connect the Component Video Input to Component Video output
of compatible source components, typically a DVD player, BD player,
digital cable box or other applicable components.
• Be sure to observe consistency in connecting the Y/Pb/Pr jacks to
the corresponding sources.
5 AUDIO 3 IN/OUT
• Connect AUDIO 3 OUT to the corresponding analog audio input
of a recording component such as a cassette deck, CD recorder or
to an outboard audio/video processor. Connect AUDIO 3 IN to the
component’s corresponding analog audio output connectors.
• The signal present at the AUDIO 3 OUT is determined by the source
last selected via the front panel Source keys or the AVR 4’s input
select keys with the exception of Source 3 or Source 4. If the default
settings are maintained for both Source 3 and Source 4 (analog
audio input is AUDIO 3) and both their respective digital audio
input is set to “Off”, there will be no output at AUDIO 3 OUT when
Source 3 or Source 4 is selected. This prevents feedback through the
recording component thereby preventing possible damage to your
speakers.
IDENTIFICATION OF CONTROLS
9 IR IN
• This input is connected to the output of an IR (infrared) repeater
(Xantech or similar) or the IR output of another component to allow
control of the T 748 from a remote location.
10 MP DOCK
The T 748 is equipped with a data port in the rear panel where an
optional NAD IPD (NAD IPD Dock for iPod) 1, NAD IPD 2 and later
variants can be plugged in.
• Connect the “MP DOCK (DATA PORT)” jack of the T 748 to the
corresponding “DATA PORT” socket of the optional NAD IPD model.
• AUDIO 2 IN and S-VIDEO IN are the assigned default ports for the
audio/video output of the separately sold NAD IPD (NAD IPD Dock
for iPod) 1, NAD IPD 2 and later variants.
• Refer also to the “LISTENING TO YOUR iPod PLAYER” segment of the
“OPERATION” section.
NOTE
The NAD IPD Dock for iPod is not supplied with your T 748.
FRANÇAIS
ESPAÑOL
PORTUGUÊS
8 DIGITAL AUDIO (COAXIAL 1-2, OPTICAL 1-2)
• Connect to the corresponding optical or coaxial digital output of
sources such as CD or BD/DVD players, digital cable box, digital
tuners and other applicable components.
• Coaxial and Optical digital input association is configurable via the
Source Setup item of the Setup Menu OSD.
NOTE
Use stranded wire of at least 16 gauge (AWG). Connections to the T 748 can
be made with banana-type plugs. Bare wire or pins can also be used by
loosening the terminal’s plastic nut, making a clean, neat connection, and
re-tightening carefully. To minimize the danger of short circuit, ensure that
only 1/2-inch of exposed wire or pin is employed when connecting.
ITALIANO
WARNING
Before connecting and disconnecting any HDMI cables, both the T 748
and the ancillary source must be powered OFF and unplugged from the
AC outlet. Failure to observe this practice may cause permanent damage
to all equipment connected via HDMI sockets.
13SPEAKERS
• Connect the respective speaker’s FRONT L, FRONT R, CENTER,
SURR R, SURR L, SURR-BACK L, and SURR-BACK R channels to their
corresponding loudspeakers. Make sure the “+” (red) terminal and
“-” (black) terminal are connected to the corresponding “+” and “-”
terminals of the loudspeaker. Use extra care to ensure that no stray
wires or strands cross between posts or terminals at either end.
• The T 748 is designed to produce optimum sound quality when
connected to speakers with impedances within its operating range.
Please make sure that all the speakers are rated 8 ohms minimum
per speaker.
14 AC MAINS INPUT
The T 748 comes supplied with a separate detachable mains power
cord. Before connecting the plug to the mains power source, ensure
that it is firmly connected to the T 748’s AC Mains input socket first.
• Connect only to the prescribed AC outlet, i.e., 120V 60 Hz (for 120V
version models only) or 230V 50 Hz (for 230V version models only).
• Always disconnect the mains power plug from the mains power
source first, before disconnecting the cable from the T 748’s AC
Mains input socket.
DEUTSCH
7 HDMI (HDMI 1-4, HDMI MONITOR OUT)
• Connect the sets of HDMI input to the HDMI OUT connectors of
source components such as DVD player, BD player or HDTV satellite/
cable box. Connect the HDMI Monitor OUT to a HDTV or projector
with HDMI input.
NOTE
Never connect both the external amplifier and T 748’s speaker outputs to
the same set of speakers.
NEDERLANDS
NOTE
The external NAD DAB Adaptor module is not supplied with your T 748.
12 AUDIO PRE-OUT
• The AUDIO PRE- OUT makes it possible to use the T 748 as a preamplifier to external power amplifiers for some or all channels.
Connect FRONT L, FRONT R, CENTER, SURR R, SURR L, SURR-BL and
SURR-BR to the respective channel input of a power amplifier or
amplifiers driving the corresponding applicable speakers.
• Unlike the full range channels, there is no power amplifier built-into
the T 748 for a subwoofer. Connect the SUBW output to powered
(“active”) subwoofers or to power amplifier channels driving a
passive system.
15 SWITCHED AC OUTLET
This convenience outlet can supply switched power to another
component or accessory.
• The total draw of all devices connected to this outlet must not
exceed 100 watts.
• It is powered ON and OFF by the front panel STANDBY button or by
the AVR 4’s ON and OFF keys.
SVENSKA
6 DAB MODULE INPUT (230V version model only)
The T 748 is compatible only with the NAD DAB Adaptor module
models DB 1 or DB 2.
• Plug-in the other end of the Mini-Din connector from the NAD DAB
Adaptor module output port into this socket.
• With DAB, you can receive CD-like quality programs without any
annoying interference and signal distortion.
• Refer also to the “LISTENING TO DAB RADIO” segment of the
“OPERATION” section.
ENGLISH
REAR PANEL
РУССКИЙ
11 RS 232
NAD is a certified partner of AMX and Crestron and fully supports
these external devices. Check out the NAD website for information
about AMX and Crestron compatibility with NAD. See your NAD audio
specialist for more information.
• Connect this interface using RS-232 serial cable (not supplied) to
any Windows compatible PC to allow remote control of the T 748
via compatible external controllers.
9
IDENTIFICATION OF CONTROLS
AVR 4 REMOTE CONTROL
ENGLISH
USING THE AVR 4 REMOTE CONTROL
1
2
FRANÇAIS
3, 4
7
6
5
8
9
ESPAÑOL
10
The AVR 4 remote control handset handles the key functions of the T 748. The AVR 4 can also be
used to directly command other NAD products that respond to applicable common remote control
codes. This includes other NAD Stereo Receiver, Integrated Amplifier and Preamplifier models. It has
additional controls to remotely operate NAD CD Players, AM/FM Tuners and dedicated AM/FM/DAB
Tuners. It will operate up to a distance of 23ft (7m). Alkaline batteries are recommended for maximum
operating life. Two AA batteries should be fitted in the battery compartment at the rear of the Remote
Control handset. When replacing batteries, check that they have been put in the right way round, as
indicated on the base of the battery compartment.
NOTE
The remote control handset supplied with the T 748 is of a universal NAD type, designed to operate
several NAD models. Some buttons are applicable only to specific NAD models. Contact your dealer
or NAD audio specialist for assistance.
1 ON, OFF
The AVR 4 remote has a separate ON and OFF button.
• Press ON button to switch the T 748 from Standby to operating mode. Press OFF button to
switch the T 748 to Standby mode.
11
PORTUGUÊS
14
13
12
15
2 DEVICE SELECTOR
A Device Selector button determines only what component the AVR 4 will command; it does not
perform any function on the T 748.
• Press desired Device Selector button for the applicable buttons to be directed to a “page” of
commands relevant to the selected device. Upon selecting a Device, you can now press the
corresponding AVR 4 control buttons applicable for the selected Device.
ITALIANO
3 INPUT SELECTORS
Refer to the corresponding labels printed in the remote control faceplate and their respective
assigned buttons to make use of these functions.
• Set the DEVICE SELECTOR to “AMP” in order to gain access to these buttons.
• INPUT 1, INPUT 2 up to INPUT 5 corresponds to T 748’s Source 1, Source 2 up to Source 5. Select
FRONT to select Front Input and MP for Front Audio MP input.
DEUTSCH
4 NUMERIC KEYS
The numeric keys allow for direct input of tracks for CD players and direct channel/preset access for
tuners and receivers.
5 A/V PSET
In combination with the numeric keys, press a Preset number from 1 to 5 as referenced to A/V
Presets settings. Note that the Preset settings can be configured via the A/V Presets menu.
NEDERLANDS
6DIMMER
• Reduce or restore VFD brightness.
• Depending on the NAD model, the brightness of the front panel display will vary when you
toggle this button.
• Use with NAD T 748 and other compatible NAD Stereo Receiver, Tuner and CD Player models.
7TEST
Initiate speaker TEST mode while at the Speaker Levels section of the Speaker Setup menu.
SVENSKA
8MUTE
• Temporarily mutes audio output or restores audio from mute mode.
• MUTE mode is indicated by flashing Standby LED indicator for NAD Integrated Amplifiers or
“Mute” shown in the VFD of NAD Receivers.
• Adjusting the volume level via the AVR 4 or the front panel volume knob will automatically
release the mute function.
РУССКИЙ
9SURR
Select desired listening or surround mode.
10
IDENTIFICATION OF CONTROLS
ENGLISH
AVR 4 REMOTE CONTROL
10 p VOL q
• Increase or decrease loudness level. Release the button when desired level is reached.
• The VFD on the front panel will indicate the level set. For NAD Receivers, the VFD will also show
“Volume Up” or “Volume Down” or “Volume: _ _ dB” (_ _ indicates the numerical dB level) while
pressing AVR 4’s [VOL p/q ] buttons.
FRANÇAIS
11 D/F/A/S, ENTER
Select an item in a menu.
12SLEEP
Switch off the NAD Receiver or Tuner after a preset number of minutes.
PORTUGUÊS
ESPAÑOL
SLEEP MODE
The Sleep Mode timer will switch the T 748 to Standby mode automatically after a preset number of
minutes. Pressing the AVR 4’s [SLEEP] button once will display the current setting of the sleep time
mode or remaining time before the T 748 goes to standby mode. Pressing the AVR 4’s [SLEEP] button a
second time within a 3-second period will change the sleep time mode to the next sleep time setting.
Each consecutive press increases the sleep time in 15-minute increments from 15 to 90 minutes. To
cancel the sleep mode, continue pressing the AVR 4’s [SLEEP] button until “Sleep Off” is displayed on
the VFD. Switching the T 748 to standby mode from either the AVR 4’s OFF or the T 748’s Standby
button will also cancel the sleep mode.
13EQ
Enable or disable Equalization (EQ) effect as set up at Auto Calibration.
14TONE
Adjust Treble or Bass level. Toggle [TONE] and then use [ D/F ] buttons to set up tone level.
ITALIANO
15L.NITE
Set Dynamic Range Control (DRC) level. Toggle [L.NITE] to select either DTS or Dolby DRC setting
and then use [ D/F ] buttons to set up DRC level.
РУССКИЙ
SVENSKA
NEDERLANDS
DEUTSCH
DVD/BD/CD PLAYER CONTROL (USE WITH COMPATIBLE NAD CD PLAYER, BLU-RAY DISC
PLAYER OR DVD PLAYER MODELS)
Set the DEVICE SELECTOR to “BD” in order to gain access to these buttons. Some of the control buttons
below are applicable only to specific NAD CD Player, Blu-ray Disc or DVD Players; check the owner’s
manual of your NAD model for control button compatibility. You can also load the applicable NAD
code library to this device so that it can be made compatible with your other NAD equipment. Refer
to the section below about “LIBRARY” on how to load a NAD code library.
HOME: Display or exit HOME menu.
PICTURE: Display or exit the Picture Mode menu.
TITLE/POP-UP: Display DVD title menu or BD-ROM pop-up menu, if available.
MENU: Access disc menu, if available.
SCAN [ 7/8 ]: Fast reverse/forward search.
[ k ]: Open or close disc tray.
[ g ]: Stop playback.
[ ; ]: Pause playback temporarily.
[ 0 ]: Go to next track, chapter or file.
[ 9 ]: Go to the beginning of current or previous track, chapter or file.
[ 4 ]: Start playback.
ENTER: Select desired track, folder or WMA/MP3 file.
DISP: Show playback time and other display information.
RAND: Play tracks/files in random order.
RPT: Repeat track, chapter, file or whole disc.
PROG: Enter or exit program mode.
CLEAR: Delete programmed track/file.
RES: Set output resolution of HDMI and Component Video output.
SETUP: Access or exit setup menu.
A,B,C,D: Navigate or select BD-ROM menu, if applicable; Page up/down PHOTO and MUSIC menu
list.
11
IDENTIFICATION OF CONTROLS
AVR 4 REMOTE CONTROL
ENGLISH
FRANÇAIS
TUNER CONTROL (USE WITH T 748 TUNER SECTION AND OTHER COMPATIBLE NAD
RECEIVER, AM/FM/DAB TUNER MODELS)
Set the DEVICE SELECTOR to “TUN” in order to gain access to these buttons. Refer to the corresponding
labels printed in the remote control faceplate and their respective assigned buttons to make use of
these functions. Some of the control buttons below are applicable only to specific NAD Receiver
or Tuner models; check the owner’s manual of your NAD Receiver or Tuner for control button
compatibility. You can also load the applicable NAD code library to this device so that it can be made
compatible with your other NAD equipment. Refer to the section below about “LIBRARY” on how to
load a NAD code library.
TUNE [ 7/8 ] or [ A/S ]: Tune forward or backwards.
INFO: Repeatedly pressing this button will show information as supplied by the current radio
station. The applicable display contents include related DAB display information and RDS
broadcast data.
PRESET [ 9/0 ] or [ D/F ]: Step up or down Preset numbers.
[ A/S ]: In combination with [TUNER MODE] or other compatible buttons, select through applicable
DAB menu options.
ENTER: Select Preset or Tune mode at AM/FM band. Display signal strength at DAB mode.
AM/FM/DB: Select DAB, FM or AM band, as applicable.
TUNER MODE: In FM mode, toggle between “FM Mute On” and “FM Mute Off”. At DAB mode,
use the [TUNER MODE] button in combination with the front panel [A/S] and [ENTER] buttons to
activate DAB menu options.
BLEND: Engage or disengage BLEND feature. This is not applicable to T 748.
MEMORY: Save current station to a Preset number.
DELETE: Delete selected Preset number.
ESPAÑOL
PORTUGUÊS
NOTE
For iPod player-specific control buttons, please refer to “CONTROL FEATURES” under “OPERATION LISTENING TO YOUR iPod PLAYER”.
ITALIANO
DEUTSCH
NEDERLANDS
SVENSKA
РУССКИЙ
12
IDENTIFICATION OF CONTROLS
ENGLISH
AVR 4 REMOTE CONTROL
LIBRARY
The AVR 4 can store a different library of default NAD codes for each of its DEVICE SELECTOR “pages.”
If the original default library does not control your NAD CD player, DVD player, or other component,
follow the procedure below to change the library code. Refer as well to the table below for a list of
applicable NAD Library Codes with their corresponding NAD models.
ESPAÑOL
FRANÇAIS
LOAD ANOTHER LIBRARY CODE
Example: Load NAD DVD Player T 517 library code to AVR 4’s “BD” device.
1 Press and hold [BD] in the DEVICE SELECTOR section of AVR 4.
2 While holding down the device button [BD], press “2” and “2” using AVR 4’s numeric buttons. “22” is
the corresponding library code for T 517.
3 Press [ENTER] while still holding down the device button [BD]. The BD device selector will flash
once to indicate that the library input is successful. Both the device selector button [BD] and
[ENTER] can now be released.
PORTUGUÊS
RESET THE AVR 4 TO ITS DEFAULT SETTINGS
The AVR 4 can be restored to its factory settings, including default libraries, via the following
procedures
1 Press and hold [ON] and [DELETE] buttons for about 10 seconds until the AMP device button lights
up.
2 Within two seconds of the AMP device button lighting up, release both buttons. If the reset mode
is successful, the [BD] device button will flash twice.
NAD PRODUCT DESCRIPTION
10
Default library for “AMP” page
11
Zone 2
20
C 515BEE, C 545BEE, C 565BEE
21
T 535, T 585, M55; DVD section of L 54, VISO TWO, VISO FIVE
22
T 513, T 514, T 515, T 517
23
T 587, T 557, T 577, M56
30
IPD 1
31
IPD 2
40
Default library for “TUN” page; Tuner section of C 725BEE, T 175, T737, T 748, T 755, T 765,
T 775, T 748
41
C 422, C 425, C 426
42
C 445
DEUTSCH
LIBRARY CODE
ITALIANO
TABLE OF LIBRARY CODES APPLICABLE TO AVR 4 REMOTE CONTROL
РУССКИЙ
SVENSKA
NEDERLANDS
NOTE
The AVR 4 may not necessarily contain all the control buttons applicable for the above-mentioned
NAD products. Use the prescribed remote control of the specific NAD product for a full compliment
of the applicable remote control buttons.
13
OPERATION
USING THE T 748 - MAIN MENU
ENGLISH
ABOUT THE ON-SCREEN DISPLAY (OSD)
LISTENING MODE
The T 748 employs a simple, self-explanatory system of on-screen display
“menus” that will appear on the connected video monitor/TV. These are
required during the setup process (and are useful in day-to-day operation),
so be sure to connect the monitor/TV before proceeding with the setup.
FRANÇAIS
DISPLAY THE OSD
Press [ S ] or [MENU] buttons of the AVR 4 remote control or the front
panel buttons [ s ] or [MENU] to display the T 748’s Main Menu on your
video monitor/TV. If the OSD does not appear, check your MONITOR OUT
connections.
ESPAÑOL
PORTUGUÊS
NAVIGATING THE OSD AND MAKING CHANGES
Use applicable AVR 4 or corresponding front panel buttons to navigate
through the OSD menu options.
1 Press [ S ] to select a menu item. Use [ D/F ] or in some cases, [ENTER],
to move up or down the menu selections. Repeatedly press [ S ] to
advance or go further into the sub-menu of desired menu item.
2 Use [ D/F ] to set or change the parameter value (setting) of a menu
item.
3 Press [ A ] to save the settings or changes done on the current menu or
sub-menu. Pressing [ A ] will also return the user to the previous menu
or exit from a particular menu.
IMPORTANT NOTE
Unless otherwise specifically stated, references to control buttons in the
succeeding sections are with respect to AVR 4 buttons. Equivalent front
panel buttons apply when applicable.
ITALIANO
MAIN MENU
DEUTSCH
NEDERLANDS
The Main Menu contains the menu options for “Listening Mode”, “DSP
Option”, “Tone Controls” and access to “Setup Menu”.
Follow the guidelines about “DISPLAY THE OSD” and “NAVIGATING THE OSD
AND MAKING CHANGES” to navigate through the menu options and their
sub-menu selections.
SVENSKA
NOTE
The individual configurations set forth at “Listening Mode”, “DSP Option”
and “Tone Controls” are carried over whenever they are enabled at “A/V
Presets Setup” setting. Please see the section “A/V Presets Setup” for
reference.
РУССКИЙ
14
The T 748 offers distinct listening modes, tailored for different types of
recording or program material. With a two-channel (Stereo) source, the
following listening modes can be selected.
STEREO
Output is directed to the front left/right channels. Low frequencies are
directed to the subwoofer if one is present in the Speaker settings. Select
“Stereo” when you wish to listen to a stereo (or monaural) production, such
as music CD or FM broadcast, without surround enhancement. Stereo
recordings whether in PCM/digital or analog form and whether surroundencoded or not encoded, are reproduced as recorded. Multi-channel digital
recordings (Dolby Digital and DTS) are reproduced in “Stereo Downmix”
mode via the front left/right channels only as Lt/Rt (left/right-total) signals.
DIRECT
The analog or digital sources are automatically played in their native
formats. All the source’s audio channels are reproduced directly. This
mode recreates the original sound most faithfully thereby producing
outstandingly high quality audio. Note that the source must be at playback
mode for “Direct” to become available as a listening mode option. In order
to automatically playback your source in their native format, implement the
following settings.
1 Go to “Listening Mode Setup” under “Setup Menu”. At the “Listening
Modes” menu, set all Dolby Digital, DTS, PCM and Analog settings to
“None”. With this setup, your source will be played back directly at its
native format.
2 Next, go to “A/V Presets Setup” under “Setup Menu”. At “A/V Presets
Setup” menu, set “Listening Mode” item to “Yes” and then save this
setting among other options, say to “Preset 1”, by selecting “Save
Settings to Setup”.
3 Now, you can associate “Preset 1” to any of the “Source” settings. For
example, at Source 1 setting under “Source Setup (Normal)”, scroll down
to “A/V Preset” item and set it to “Preset 1”. Thus whenever Source 1 is
selected, the associated source will always be directly played back at its
native audio format.
OPERATION
7.1 Speaker System
PLIIx Music
PLIIx Movie
Front (left and right), Center,
Surround (left and right), Back
Surround, Subwoofer
Front (left and right),
Center, Surround
(left and right), Back
Surround (left and
right), Subwoofer
NEO: 6
Two-channel recordings, whether stereo or surround-encoded, are
reproduced with NEO:6 surround with output to front left/right, center and
discrete left/right surround channels plus subwoofer (assuming these are
present in the current “Speaker Configuration”). The T 748 provides two DTS
NEO:6 variations – NEO:6 Cinema and NEO:6 Music. See also section about
“Adjusting Listening Modes” below.
EARS
Two-channel recordings, whether stereo or surround-encoded, are
reproduced with proprietary NAD surround processing with signal output
to the front left/right, center and discrete left/right surround channels,
plus subwoofer (assuming these are present in the current “Speaker
Configuration”). EARS does not employ the surround back speakers (if any).
EARS extracts the natural ambience present in nearly all well-produced
stereo recordings. It does not synthesize any ambience or other sonic
elements and thus remains truer to the sound of the original musical
performance than most other music-surround options.
Select EARS for listening to stereo music recordings and broadcasts.
EARS produces a subtle but highly natural and believable ambience from
nearly all “natural-acoustic” stereo recordings. Typically, these include
classical, jazz, and folk genres as well as numerous examples from others.
Its virtues include realistic, stable “front-stage” sonic imaging and spacious
but unexaggerated ambient “virtual acoustics” that remain faithful to the
original recording.
FRANÇAIS
NOTE
Listening Mode parameter changes are maintained when you change
listening modes. You may also save a modified Listening Mode for easy
recall by saving it to a Preset (See “A/V Presets Setup” below under Setup
Menu discussions).
PRO LOGIC IIx
PLIIx MOVIE is optimized for film soundtracks.
PLIIx MUSIC for music recordings.
Center Width (0 to 7): Modifies the “hard-centeredness” of the center
image, by gradually mixing mono center content to the Front left/right
speakers as well. A setting of “0” retains the center-channel-only default
while a setting of “7” yields a fully phantom center channel.
Dimension (-3 to 3): Adjusts front-rear emphasis of the surround effect
independently from the relative channel levels.
Panorama (On/Off): Adds a “wraparound” effect by extending some
stereo content into the surround channels.
NOTE
Pro Logic IIx mode will decode as Pro Logic II mode when the BACK
surround speakers are set to “Off” from “Speaker Configuration” menu.
See also section about “Speaker Configuration” under “Speaker Setup” of
the Setup Menu.
DTS NEO: 6
NEO:6 Cinema is optimized for film soundtracks.
NEO:6 Music for music recordings
Center Gain (0 to 0.5): Adjust for better center image in relation to the
surround sound channels.
SVENSKA
ENHANCED STEREO
All recordings are reproduced in stereo via the maximum speaker
complement configured in the current “Speaker Configuration”. Enhanced
stereo can be useful for maximum volume from all channels or for multispeaker background music (cocktail party) listening. For this mode, Front,
Center, Surround and Back speakers can be turned ON/OFF as desired.
ESPAÑOL
6.1 Speaker System
PORTUGUÊS
Active Decoded Output Channels
ITALIANO
Listening Mode
Two-Channel
Sources
Several of the T 748’s listening modes have one or more selectable
variations and adjustable parameters that you can modify to suit
your system or personal preferences. At Listening Mode menu, use a
combination of [ D/F ] keys to navigate and achieve desired settings.
DEUTSCH
The following chart shows the channels available assuming they are
enabled in the “Speaker Configuration” menu:
ADJUSTING LISTENING MODES
NEDERLANDS
DOLBY PRO LOGIC IIx
Dolby Pro Logic Iix processes both stereo and 5.1 signals into a 6.1 or 7.1
channel output. At Dolby Pro Logic Iix, you can either choose PLIIx Movie or
PLIIx Music mode to tailor your listening experience to the source material.
Dolby Pro Logic Iix surround processing yields more stable imaging and
full bandwidth sound to the rear channels in Movie mode offering sound
that is more similar to Dolby Digital decoding. For two channel signals,
PLIIx Music mode also features three additional user controls – Dimension,
Center Width, and Panorama. See also section about “Adjusting Listening
Modes” below.
ENGLISH
USING THE T 748 - MAIN MENU
РУССКИЙ
ANALOG BYPASS
All analog signals remain in the analog domain without analog-to-digital
conversions. At Analog Bypass, the DSP circuitry is bypassed but full tone
control functions remain. “Bass management” or Speaker settings are also
not in effect as these are DSP functions.
15
OPERATION
USING THE T 748 - MAIN MENU
ENGLISH
DSP OPTION
FRANÇAIS
ESPAÑOL
LIP SYNC DELAY
DSP Options has the feature “Lip Sync Delay” whose function is to match
any delay that may occur in the picture relative to the audio.
By varying “Lip Sync Delay” from 0ms to 120ms, one can delay the audio
output in order to synchronize it with the video image.
TONE CONTROLS
PORTUGUÊS
ITALIANO
The T 748 has two Tone Control levels – Treble and Bass. Bass and Treble
controls only affect the low bass and high treble leaving the critical
midrange frequencies free of coloration.
DEUTSCH
These controls allow one to tweak on-the-fly, the frequency response of the
source during playback. The control setting could be adjusted by navigating
through the Tone Controls’ OSD menu via a combination of [ ENTER ] and
[ A/S/D/F ]keys.
Maximum and minimum values for all three Tone Control levels are ±10 dB.
NEDERLANDS
“Tone Defeat” gives one the choice of varying or completely bypassing the
tone control section of the T 748. If “Off” is selected, the Tone Control circuits
are active.
Select “On” to bypass the Tone Controls effectively defeating the effect of
the tone control circuits.
SVENSKA
РУССКИЙ
16
OPERATION
SETUP MENU
ENGLISH
USING THE T 748 – SETUP MENU
SOURCE
The T 748 is equipped with ten configurable Sources. A particular Source
can be enabled or disabled, renamed, assigned analog and digital audio
sources, video sources, A/V Presets among other settings.
NAME
A new Name maybe assigned to a Source label. For example, if your BD
player is attached to “Source 1”, it is possible to rename “Source 1” to “BD”.
There are three sub-menu items under Source Setup. These are Source
Setup (Normal), Source Setup (Table ) and iPod Setup.
In order to rename the Source label, scroll to the “Name” parameter. Press
[ S ] to go to the first character. Then, press [ D/F ] to pick through the
alphanumeric selections.
Press [ S ] to move to the next character and at the same time save the
changes done on the current character. The name can be as long as eight
characters.
The new Name will be shown in the VFD as well as on the OSD.
SOURCE SETUP (NORMAL)
The Source Setup (Normal) menu makes it possible to set, allocate or
change the following settings.
ANALOG AUDIO
The T 748 has five analog audio inputs. These analog inputs - Audio 1, Audio
2, Audio 3, Audio Fr (Front) and Audio MP can be variably assigned to each
Source.
Scroll to “Analog Audio” and then press [ S ] and then [ D/F ] to select and
assign an analog audio input to the particular Source.
NOTE
An incoming digital signal present at the assigned digital input will
always take precedence over the assigned analog audio input, even if
both are present. To maintain the analog audio input for the particular
Source, select “Off” at the “Digital Audio” setting of the same “Source”
menu.
GAIN
Gain adjustment allows all sources to play back at the same volume level so
you don’t need to adjust the volume every time a new source is selected. It
is generally preferable to reduce the level of the loudest source rather than
making louder the softer sources.
Scroll to “Gain”, press [ S ] and then [ D/F ] to step through the desired level
from -12dB to 12dB.
17
ESPAÑOL
ITALIANO
SOURCE SETUP
DEUTSCH
Select “Yes” to enable the particular Source or “No” to disable the Source.
NEDERLANDS
Follow the guidelines about “DISPLAY THE OSD” and “NAVIGATING THE OSD
AND MAKING CHANGES” to navigate through the menu options and their
sub-menu selections.
PORTUGUÊS
ENABLED
One can enable/disable a Source via this option. This is particularly useful
if only few Sources are used and one directly selects the Source from the
front panel, bypassing unused sources.
SVENSKA
At Setup Menu, the following are configurable – Source Setup, Speaker
Setup, Amplifier Setup, HDMI Setup, Listening Mode Setup, Display Setup
and A/V Presets Setup.
РУССКИЙ
The Setup Menu allows one to customize the operation of the T 748 to the
ancillary equipment used in one’s specific AV system. Unless your system
exactly matches the factory defaults, you will need to use the setup menu
to configure the inputs of the T 748.
NOTE
Source 5 is defaulted to iPod. Remove the default setting of Source 5 to
iPod via the following procedure
1 Go to “iPod Setup” menu under the “Source Setup” menu. At “iPod
Setup” menu, set “Enabled” to “No”.
2 Then, go back to “Source Setup” menu and select “Source Setup
(Normal).
3 Go to Source 5 and set “Enabled” to “Yes”.
Source 5 can now be configured to any desired settings.
FRANÇAIS
These settings can be implemented through the following parameters.
OPERATION
USING THE T 748 – SETUP MENU
ENGLISH
DIGITAL AUDIO
To take advantage of the T 748’s high performance surround and digital
audio circuitry, it is advisable that its Digital Audio inputs are selected.
FRANÇAIS
There are three types of Digital Audio input for the T 748. These are HDMI,
Optical and Coaxial digital inputs. A fourth option is “Off” whereby no
incoming digital audio signal is selected by the particular Source.
The desired digital audio input for a particular Source can be selected by
scrolling to “Digital Audio”, press [ S ] and then [ D/F ] to step through the
desired digital input source. After finalizing the desired type of Digital Audio
input, press [ S ] and then [ D/F ] again to select the specific Digital Audio input.
ESPAÑOL
The following are the sets of assignable Digital Audio input:
HDMI HDMI 1, HDMI 2, HDMI 3, HDMI 4
Optical Optical 1, Optical 2, Optical Fr
Coaxial Coaxial 1, Coaxial 2
A/V PRESET
A particular Source can be assigned a stored Preset. The parameters set up
in the selected Preset number will be adopted into the particular Source it
is assigned (Please refer to the separate section on “A/V Presets Setup” for
further understanding of Preset settings).
Scrolling to “A/V Preset” and by pressing [ S ] and then [ D/F ], a Source
could be assigned a Preset number ranging from Preset 1 to 5.
If it is desired not to assign the particular Source a Preset setting, select
“None”.
SOURCE SETUP (TABLE)
The Source Setup (Table) reflects the settings made in the Source Setup
(Normal) menu. All the Source settings are summarized and displayed in
tabulated form in the Source Setup (Table).
PORTUGUÊS
NOTE
An incoming digital signal present at the assigned digital input will
always take precedence over the assigned analog audio input, even if
both are present. To maintain the analog audio input for the particular
Source, select “Off” at the “Digital Audio” setting of the same “Source”
menu.
ITALIANO
VIDEO
There are four types of video input a particular Source could be assigned.
These are HDMI, Comp (Component), S-Vid (S-Video) and Video inputs. A
fifth option is “Off” wherein the particular Source is prompted not to select
any Video input.
DEUTSCH
Navigate through the Video input selections by pressing [ S ] and then
[ D/F ] to step through the selections. The following are the sets of
assignable Video input:
HDMI HDMI 1, HDMI 2, HDMI 3, HDMI 4
Component Video Comp 1
S-Video S-Vid 1, S-Vid Fr
Video Video 1, Video 2, Video Front
Navigating through the Source Setup (Table) via a combination of [ A/S ]
and then [ D/F ] buttons, one will have the benefit of directly changing the
settings for “Audio”, “Video”, “Preset” and “Source Name” without going back
to the Source Setup (Normal) menu.
Highlight a particular Source number and then, toggle [ENTER] button to
enable or disable said Source number.
iPod SETUP
NEDERLANDS
VIDEO FORMAT CONVERSION
The T 748 is equipped with a Video Format Converter. This allows for a
simplified video connection between the T 748 and your TV Monitor when
using multiple video formats such as Composite (CVBS), S-Video, and
Component (YUV). This format change is accomplished by encoding the
analog video signal into a digital signal using a very high quality digital
encoder to maintain the best possible picture quality.
SVENSKA
Once in digital format, the video input signal could also be available at
the other Monitor output jacks including HDMI MONITOR OUT. Thus, you
do not have to necessarily assign the video output of a composite video
input signal to MONITOR OUT (Composite video). The composite video
input signal can be viewed also at HDMI MONITOR OUT at a resolution
setting dependent upon your TV/Monitor’s resolution capability. Some TV/
Monitors will automatically display the video signal at 480p/576p if they are
not capable of displaying 480i/576i.
The iPod Setup menu allows you to preset the following associated settings
when iPod is the selected source.
Enabled: Select “Yes” to enable iPod as a Source or “No” to disable it.
Auto Connect: Select “Yes” to automatically enable and connect the
iPod player docked in the linked NAD iPod docking station when Source
5 (the default iPod source allocation in the T 748) is selected. Select “No”
if you do not want a docked iPod to be automatically connected.
РУССКИЙ
Menu Timeout: Set the time for the OSD to revert to the “Now
Playing” display when the iPod menu has been left idle (no scrolling or
navigation being done) for the specified time out time. For the “Now
Playing” OSD to be shown, there should be a song paused or being
played before going to the iPod menu. You can set the “Menu Timeout”
between the range 5s to 60s at 5s increments. If you do not want for
the menu to timeout, select “0s”.
18
OPERATION
SPEAKER SETUP
After connecting all ancillary sources and other combinations, the Speaker
Setup menu will guide you on how to manage and setup your speakers in
order to achieve optimum sound acoustics in your listening environment.
MEASUREMENT IS THE FIRST STEP.
Connect the microphone jack into the front panel’s MP/MIC input. Place the
supplied microphone in the listening position at about the same height as
your listening ears. The microphone has a threaded insert at its base that
makes possible for it to be mounted on a tripod.
ENGLISH
USING THE T 748 – SETUP MENU
This is a one-time set up, unless speakers are moved or changed, in which
case the calibration should be performed again.
PORTUGUÊS
ITALIANO
DEUTSCH
NOTES
• Auto calibration is possible only for a 7.1 or 5.1 speaker configuration.
For other speaker configurations, like a 2.1 setup, you have to
manually set them up by referring to the guidelines below for Speaker
Configuration, Speaker Distance and Speaker Levels.
• The test tone emitted during measurement is loud. This maybe
bothersome for you and may affect as well your other household
members and even your neighbor.
ABOUT EQUALIZATION
Equalization is one of the parameters automatically adjusted when the
Auto Calibration feature is initiated. If after Auto Calibration, the resulting
equalization effect does not suit your taste or preference, you have the
option to turn off such equalization effect. Below is the procedure on how
to turn off equalization.
1 Ensure that auto calibration is completed. Equalization cannot be
turned ON or OFF if auto calibration is not performed and completed.
2 Using the AVR 4 remote control and with Device Selector set to AMP
page, direct the AVR 4 to the T 748’s remote sensor.
3 Press and hold AVR 4’s [EQ] button until the upper line of the VFD shows
“Adjusting EQ” and the lower line “OFF”; equalization is now turned OFF.
4 If you decide to turn ON again the calibrated equalization effect, press and
hold AVR 4’s [EQ] button until the upper line of the VFD shows “Adjusting
EQ” and the lower line “ON”; equalization is now turned back ON.
It is recommended that you take full advantage of the T 748’s Auto
Calibration feature for your speaker setup. However, if you desire to setup
your speakers manually or if you already had Auto Calibration but would
like to make adjustments, Speaker Configuration, Speaker Levels and
Speaker Distance can be manually set up via their respective setup menu.
19
NEDERLANDS
The following parameters are automatically measured and adjusted
accordingly.
• Noise Level: Check noise level relative to each speaker and subwoofer.
• Number of Speakers: Speaker configuration is detected including
number of surround speakers and whether a subwoofer and center
channel is connected.
• Speaker Distance: Accurately set the appropriate distance of
each speaker position as well as the subwoofer with respect to the
microphone position.
• Speaker Level and Size: T 748 crossover is set based on each
channel’s signal handling capability and the subwoofer crossover
is automatically set. SPL (Sound Pressure Level) of each speaker is
matched with respect to the microphone position.
• Equalization: Adjust tonal quality (bass/treble level) for each speaker.
This applies to all sound fields and for each speaker.
SVENSKA
The Auto Calibration featured in T 748 uses a microphone, along with
sophisticated digital electronics built into your T 748, to automatically setup
and calibrate the T 748 to the exact speakers and speaker placement of
your own unique Home Theatre.
A special test tone is sent to each speaker and the data is memorized
by the T 748. The duration of setup may take some time depending on
the number of speakers. After the measurements, the T 748 calculates
the ideal system response for your particular room and speaker setup. If
some inconsistencies or discrepancies are detected during the setup, the
process maybe interrupted or the problem is shown in the particular setup
window. A notice screen is correspondingly displayed. After following and
undertaking the displayed instructions, re-start the Auto Calibration setup
again. When the measurements are finalized, the ideal system response is
calculated for your particular room and speaker setup.
РУССКИЙ
AUTO CALIBRATION
It has been shown that many, if not most, surround sound systems are not
accurately setup and calibrated. To be done properly, calibration requires
special knowledge and instrumentation that the average person probably
doesn’t possess.
The sound at your main listening position is setup using the supplied
microphone. Depending upon the availability of speakers, you can
select either 7.1 or 5.1 setup. Upon selection of either 7.1 or 5.1, the auto
calibration starts – refer to the OSD as auto calibration steps through each
measurement parameter.
ESPAÑOL
FRANÇAIS
The following are the Speaker Setup Menu sections.
OPERATION
USING THE T 748 – SETUP MENU
ENGLISH
SPEAKER LEVELS
Every surround-sound system requires “bass-management” to direct lowfrequency content from any or all channels to the speakers best able to
reproduce it. For this function to operate correctly, it is important that you
correctly identify your speakers’ capabilities. We use the terms “Small” and
“Large” (and “Off”) but note that physical size may be irrelevant.
• A “Small” speaker is any model, regardless of physical size, that lacks
significant deep-bass response, that is, below about 150 Hz.
• A “Large” speaker is any full-range model; that is, one with deep-bass
response
• An “None” speaker is one that is not present in your system. For example,
you might not have any surround-back speakers installed; in that case,
you would set the “Back” setup item to “None”.
Adjusting the relative balance of your system’s loudspeakers ensures that
surround-sound recordings, whether music or film, will present the balance
of effects, music, and dialog that the artists intended. Additionally, if your
system incorporates a subwoofer, it establishes a correct relationship
between the volume of the subwoofer and the other speakers, and thus of
low-frequencies (bass) to other sonic elements.
FRANÇAIS
SPEAKER CONFIGURATION
ESPAÑOL
PORTUGUÊS
ITALIANO
The Speaker Configuration is “global”; that is, it remains in force with all
inputs and in all listening modes. However, speaker settings are part of the
T 748’s A/V Preset system. Consequently, multiple speaker settings can be
stored for easy recall as different types of recordings or listening modes
require.
Speaker Configuration can be managed and adjusted by pressing a
combination of [ S ] and then [ D/F ] keys. Set “Front”, “Center”, “Surround”
and “Back” to “Large”, “Small” (“Small 60Hz” up to “Small 150Hz”) or “None” as
your subsystem’s speakers require.
DEUTSCH
Set “Subwoofer” to “On” or “Off,” selecting “On” only if you have a subwoofer
connected to the T 748’s SUBW output jack. If the “Subwoofer” is set to “Off”,
“Front” speaker will automatically be set to “Large”.
NEDERLANDS
ENHANCED BASS
When the subwoofer is set to “On” and “Front” is set to “Large”, Enhanced
Bass becomes available. Normally, with speakers set to “Large” the
subwoofer is not active. The Enhanced Bass option allows full range
operation of the speakers with the additional bass contribution of the
subwoofer. This feature is particularly useful when one wants to experience
maximum bass output. Please note that due to acoustic cancellation
effects, the bass response may be uneven when using this setting
SVENSKA
You can set Subwoofer to “On” even with “Large” front speakers, in which
case bass content from any channels set to “Small” will be routed to both
the subwoofer and to the front speakers; LFE-channel signal will pass only
to the sub. In most subwoofer-equipped systems, setting front speakers to
“Small” is usually the better option.
All the speakers’ low frequency content can be directly adjusted within the
range 60Hz to 150Hz.
РУССКИЙ
NOTE
The configurations set forth at “Speaker Setup” are carried over
whenever it is enabled during A/V Presets setting. Please see also the
section “AV Presets Setup” for reference.
20
USING AN SPL METER
It is quite practical to perform the T 748 level setup routines “by ear,” and
careful work will produce acceptably accurate results. However, the use
of an inexpensive sound-pressure level (SPL) meter, such as Radio Shack
part number 33-2050, makes this task easier, more accurate and more
repeatable. Ownership of such a meter could prove a valuable audio tool.
The SPL meter should be placed at the primary listening position, at
approximately the height of the seated listener’s head. A tripod is helpful
but with a little duct tape almost anything - a pole lamp, music-stand,
or ladder-backed chair, for example - can do as well. Just be sure that no
large acoustically reflective surfaces obstruct or are near the microphone
element.
Orient the meter with its microphone (usually at one end) pointing straight
up toward the ceiling (not toward the speakers) and ensure that “C”
weighting scale is selected. Set the meter to display 75 dB SPL. On Radio
Shack meters, this necessitates either setting the meter to its 80 dB range
and taking your readings at the -5 point or selecting the 70 dB range and
reading at the +5 point.
SETTING SPEAKER LEVELS AT TEST MODE
While at “Speaker Levels” menu, press the AVR 4 remote’s [TEST] key
activating the T 748’s Speaker Levels balancing test signal. You will hear a
“surf” sound as the test mode cycles through the speakers (“test” appears
to the right side of the current speaker), beginning with the Front Left. If
you do not hear the test signal, check your speaker connections or your
“Speaker Configuration” OSD menu settings.
Use the remote’s [ D/F ] keys to adjust the loudness of the noise output
from the currently playing channel to the required level (it’s usually simplest
to begin with the Front Left). As the test signal cycles around the speakers,
the OSD will highlight the currently playing channel. The “level offset”
reading on the right will change by 1 dB increments; ±12 dB adjustment is
available. Press [ENTER] to adjust the next speaker or for the Test mode to
continue on with the other speakers in sequence.
NOTE
If you are balancing levels “by ear”, choose one speaker - usually the
center - as a reference and adjust each of the others in turn to “sound as
loud” as the reference. Be sure that you remain in the primary listening
position while balancing all channels.
OPERATION
NOTES
• All speakers must be in their final locations before level-setting.
• Your subwoofer (if any) should be set with its integral crossover defeated,
or if undefeatable, set to its highest-possible frequency if you are using
the T 748’s Subwoofer output. Final subwoofer-level adjustment “by-ear,”
using music and film sound material, is frequently useful.
• Due to the effects of room acoustics, matched-pair speakers (front;
surround; back) will not always calibrate to exactly the same level offset
readings.
MUTING THE SOUND
Use the AVR 4’s [MUTE] key to silence all channels completely. Muting is
always available regardless of the source or listening mode selections.
NOTES
• Changing input or listening-mode selections does not release muting.
• Adjusting the volume level via the AVR 4 or the front panel volume knob
will automatically release the mute function.
AMPLIFIER SETUP
FRANÇAIS
You can exit “Test” mode at any time by pressing [ A ] key, bringing you back
to “Speaker Setup” menu. You can also press the [TEST] key to discontinue
the “Test” mode.
The T 748 will power-up from Standby mode at whatever master volume
setting was last used; however, if the prior setting was greater than -20dB,
the T 748 will power up at -20dB. This prevents inadvertently beginning a
session at excessive volume.
ESPAÑOL
To produce the same SPL meter reading (or subjective loudness), use the
remote’s [ D/F ] keys to adjust each speaker.
ENGLISH
USING THE T 748 – SETUP MENU
PORTUGUÊS
SPEAKER DISTANCE
ADJUSTING THE VOLUME
CONTROL (CEC)
Consumer Electronics Control (CEC) is a set of commands that utilizes
HDMI’s two- way communication to allow for single remote control of any
CEC-enabled devices connected with HDMI. A CEC command will trigger
the necessary commands over HDMI for an entire system to auto-configure
itself to respond to the command.
РУССКИЙ
In addition to the Volume knob, use the AVR 4’s VOL [
] to adjust the
“master volume” of the T 748 raising or lowering the channels altogether. A
momentary keypress will change the master volume by 1 dB increments. If
you hold down VOL [
], the master-volume change will “run-on” until
the key is released.
DEUTSCH
HDMI SETUP
The T 748 supports HDMI Control and Audio Return Channel (ARC)
functions. Both functions are possible if external devices that also support
both features are interconnected to the T 748 via HDMI connection.
NEDERLANDS
SETTING SPEAKER DISTANCE
While at “Speaker Distance” menu, use the [ D/F ] keys to individually
set Front Left, Center, Front Right, Surround Right, Back Right, Back Left,
Surround Left and Subwoofer to the distance measuring from your
principal listening position to the front surface of their corresponding
loudspeakers. Distance can be set up to 30 feet or 9.0 meters Distance can
be displayed as feet or meters selectable at the “Unit of Measure” item.
The Surround Back amplifier is configurable through the following settings
• Main Back: Assign as surround back speakers.
• Main Front: Provide a bi-amp mode for the Main Front speakers (Left
and Right) speakers thus reproducing the Front Left and Front Right
amplifier channel outputs.
SVENSKA
Your system’s speaker distance settings are a subtle but important
refinement of your setup. Informing the T 748 of the loudspeaker-to-listener
dimensions of each speaker automatically imposes the correct delays,
optimizing imaging, intelligibility and surround-sound ambience. Enter your
dimensions with precision within about 1 foot (30 cm).
ITALIANO
If the surround back speakers are not used in the main zone, their surround
back amplifier channels could be assigned for Main back or Main Front use.
Since recordings vary considerably in overall average level, there is no
imperative to listen at any particular master-volume setting. A setting of
-20dB may sound “as loud” from one CD or DVD as -10dB does from another.
21
OPERATION
USING THE T 748 – SETUP MENU
ENGLISH
FRANÇAIS
ESPAÑOL
When devices that support HDMI Control (CEC) are connected, the
following modes of operation can be executed via the T 748 or the external
device using any of the device’s remote control.
Source (On/Off): At “On” setting, the T 748 will automatically switch
sources if another CEC device requests a Source change.
For example, if PLAY is pressed on a BD Player with CEC, the T 748
and TV with CEC will automatically switch to their respective input
connections – the T 748 switching to the HDMI input where the BD
Player is connected while the TV will switch to its input where the
T 748’s HDMI MONITOR OUT is connected. This completes the autoconfiguration – the BD Player is automatically played back using the
T 748 and TV.
Power (On/Off): At “On” setting, the T 748 will automatically go to
standby mode if it receives a CEC standby command. On the other
hand, if the T 748 receives a CEC power up command, the T 748 will
correspondingly switch ON from standby mode.
Volume (On/Off): At “On” setting, the T 748 will respond to CEC volume
and mute commands.
PORTUGUÊS
For the above Control modes, the T 748 will not respond to any CEC
command if the particular mode is set to “Off”.
HDMI AUDIO OUT
Amp: HDMI Audio stream is sent to the T 748. Audio output is manifested
through the T 748’s speakers.
TV: HDMI Audio stream is sent to the TV. Audio output is manifested
through the TV’s speakers.
ITALIANO
HDMI ARC
HDMI ARC stands for HDMI Audio Return Channel. HDMI ARC function
enables an HDMI-ARC compatible TV to send audio data stream to the
T 748. Audio output is manifested through the T 748’s speakers.
• HDMI ARC is enabled only with “Volume” setting set to “On”. If
“Volume” is set to “Off”, HDMI ARC is automatically set to “Off”.
• “HDMI ARC” is shown in the VFD when it is set to “On” and active.
LISTENING MODES
The audio format as detected by the selected Source can be automatically
configured and processed through the following options:
DOLBY DIGITAL
Dolby Digital is the multi-channel digital signal format developed in the
Dolby laboratories. Discs bearing the Dolby Digital (double-D symbol) logo
were recorded with up to 5.1 channels of digital signals, reproducing a
much better sound quality, with dynamic and spatial sound sensations that
are much better than in the previous Dolby Surround.
A Dolby Digital audio input can be configured relative to its format as
follows
Stereo: If the detected audio is of Dolby stereo format, you can default
it to one of the following settings - Stereo, PLIIx Movie, PLIIx Music, PLIIx
Game, Neo:6 Cinema or Neo:6 Music.
Surround: If the detected audio is of Dolby Surround format, you can
default it to one of the following settings - Stereo, PLIIx Movie, PLIIx
Music, Dolby D Ex,Neo:6 Cinema or None.
None: If “None” is selected, the Dolby Digital signal will be defaulted
to the “Stereo” or “Surround” settings set forth at the “PCM” option. See
discussion below about “PCM”.
DOLBY DIGITAL SURROUND MODES
The following are further descriptions of Dolby Digital surround modes.
DEUTSCH
IMPORTANT NOTES
• The CEC or HDMI ARC response among the devices may vary or may not
be achieved as expected. This may depend upon the other devices’ setup
configuration, compatibility or capability.
• Audio and video will continuously stream from the HDMI source with
CEC to the TV with CEC even if the T 748 is at standby mode.
NEDERLANDS
LISTENING MODE SETUP
DOLBY DIGITAL PLUS
Dolby Digital Plus is the next-generation audio technology for all highdefinition programming and media. It combines the efficiency to meet
future broadcast demands with the power and flexibility to realize the full
audio potential expected in the upcoming high-definition era. Built on
Dolby Digital, the multi-channel audio standard for DVD and HD broadcasts
worldwide, Dolby Digital Plus was designed for the next-generation A/V
receivers but remains fully compatible with all current A/V receivers.
SVENSKA
Dolby Digital Plus delivers multi-channel audio programs of up to 7.1
channels and supports multiple programs in a single encoded bitstream
with the maximum bit rate potential of up to 6 Mbps and the maximum bit
rate performance of up to 3 Mbps on HD DVD and 1.7 Mbps on Blu-ray Disc.
It outputs Dolby Digital bitstreams for playback on existing Dolby Digital
systems. Dolby Digital Plus can accurately reproduce the sound originally
intended by directors and producers.
РУССКИЙ
The T 748 has various listening mode options and is mostly configurable.
These are provided to reproduce a variety of sound effects depending upon
the content of the source to be played. Use a combination of [ A/S/D/F ] to
configure the following settings.
22
It also features multi-channel sound with discrete channel output,
interactive mixing and streaming capability in advanced systems.
Supported by High-Definition Media Interface (HDMI), a single-cable digital
connection is possible for high-definition audio and video.
OPERATION
DOLBY SETUP
A DTS audio input can be configured relative to its format as follows
Stereo: If the detected audio is of Dolby stereo format, you can default
it to one of the following settings - Stereo, PLIIx Movie, PLIIx Music, PLIIx
Game, Neo:6 Cinema or Neo:6 Music.
Surround: If the detected audio is of DTS Surround format, you can
default it to one of the following settings - Stereo, PLIIx Movie, PLIIx
Music, Neo:6 Cinema, Neo:6 Music or None.
None: If “None” is selected, the DTS signal will be defaulted to the
“Stereo” or “Surround” settings set forth at the “PCM” option. See
discussion below about ‘PCM’.
Under this menu, the Dolby Digital’s Dynamic Range Control can be
adjusted as well as the settings for Dolby Digital Pro Logic IIx Music.
Dyn Range Ctrl: You can select the effective dynamic range (subjective
range from soft to loud) for playback of Dolby Digital soundtracks. For
fully cinematic effect, always select “100”, the default. Settings of 75,
50 and 25% progressively reduce dynamic range, making soft sounds
comparatively louder while limiting the peak loudness of loud ones.
The 25 setting will yield the least dynamic range and is best for latenight sessions or other times when you wish to retain maximum dialog
intelligibility while minimizing overall volume levels.
Dolby Pro Logic IIx Music: Please refer to the same description of
“PLIIx Music” under the “ADJUSTING LISTENING MODES” segment of the
“OPERATION - USING THE T 748 - MAIN MENU”.
FRANÇAIS
SVENSKA
DTS
The Digital Theater System Digital Surround (simply called DTS) is a multichannel digital signal format that can process higher data rates than with
Dolby Digital. Although both Dolby Digital and DTS are 5.1 channel media
formats, discs bearing the “DTS” symbol are thought to provide better sound
quality due to the lower audio compression required. It also offers a broader
dynamic, producing magnificent sound quality.
ITALIANO
With this additional channel you will experience improved dynamics and
a better sensation of movement within the sound field. If media sources
recorded in Dolby Digital EX are decoded with a Digital EX decoder,
the format is detected automatically, and the Dolby Digital EX mode is
selected. However, some media sources recorded in Dolby Digital EX can be
detected as simple Dolby Digital media sources. In this case Dolby Digital
EX should be selected manually.
NOTE
Please refer to the section “Listening Mode” at the Main Menu
discussions for a description of Pro Logic, PLIIx Movie, PLIIx Music and
Stereo Downmix modes.
ESPAÑOL
NOTE
All these Listening Modes for Dolby Digital, DTS, PCM and Analog
can be directly changed by pressing the “Listening Mode” button on
the front panel or through the “Listening Mode” option at the Main
Menu window. The chosen audio format will be reflected back to the
appropriate setting at the “Listening Mode Setup”.
PORTUGUÊS
DOLBY DIGITAL EX
Using a Matrix decoder, this method creates the back channel (sometimes
also called the “surround center”) by means of signals on the left and
right surround channels recorded in Dolby Digital 5.1, reproduction being
provided in Surround 6.1. This method should be selected with sources
bearing the “Dolby Digital (double-D symbol)-EX” symbol, recorded in Dolby
Digital Surround EX.
ANALOG
If the audio input is an analog signal, the following are the surround modes
the input can be defaulted - Pro Logic, PLIIx Movie, PLIIx Music, NEO: 6
Cinema, NEO: 6 Music, EARS, Enhanced Stereo, Analog Bypass and None.
DEUTSCH
It supports bit rates of up to 18 Mbps and records up to 8 full-range channels
individually with 24-bit/96 kHz audio. It also features extensive metadata
including dialogue normalization and dynamic range control. Supported by
High-Definition Media Interface (HDMI), a single-cable digital connection
is possible for high-definition audio and video. HD DVD and Blu-ray Disc
standards currently limit their maximum number of audio channels to eight,
whereas Dolby Digital Plus and Dolby TrueHD support more than eight audio
channels. Note that the T 748 only supports 7.1 channel.
PCM
PCM (Pulse Code Modulation) is the digital representation of a standard
audio signal converted with little or no compression. If “None” is selected
for any of the Dolby or DTS settings, this “PCM” section will default the audio
signal as follows
Stereo: The detected stereo audio format will be configured into one
of the following options - PLIIx Movie, PLIIx Music, PLIIx Game, Neo:6
Cinema, Neo:6 Music EARS or Enhanced Stereo.
Surround: The detected surround audio format will be configured into
one of the following options - PLIIx Movie, PLIIx Music, Neo:6 Cinema,
Stereo or None.
NEDERLANDS
DOLBY TrueHD
Dolby TrueHD is a lossless encoding technology developed for highdefinition optical discs in the upcoming era. Dolby TrueHD delivers
tantalizing sound that is bit-for-bit identical to the studio master, unlocking
the true high-definition entertainment experience on high-definition
optical discs in the next generation. When coupled with high-definition
video, Dolby TrueHD offers an unprecedented home theater experience
with stunning sound and high-definition picture.
ENGLISH
USING THE T 748 – SETUP MENU
РУССКИЙ
NOTE
Please refer to the section “Listening Mode” at the Main Menu
discussions for a description of Stereo Downmix and DTS NEO:6
surround modes.
23
OPERATION
USING THE T 748 – SETUP MENU
ENGLISH
DTS SETUP
DTS–ES MATRIX 6.1
In this format, the additional signals of the back channel receive a matrix
encoding and are inputted into the right and left surround channels.
During reproduction they are decoded to the right, left and back surround
channels.
FRANÇAIS
Since this bit-stream format is 100% compatible with conventional DTS
signals, the DTS-ES Matrix 6.1 format effect can also be achieved from
sources with DTS-ES 5.1 signals.
Naturally, it is also possible to reproduce from a DTS 5.1 channel decoder,
signals recorded in DTS-ES 6.1.
ESPAÑOL
Under this menu, the Dynamic Range Control of DTS Digital Surround can
be adjusted as well as the settings for DTS Neo: 6 Music.
Dyn Range Ctrl: This is the same configurable Dynamic Range Control
feature as described above at Dolby Setup, the only difference being
the soundtrack is now in DTS format.
DTS Neo: 6 Music: Please refer to the same description of “NEO 6:
Music” under the “ADJUSTING LISTENING MODES” segment of the
“OPERATION - USING THE T 748 - MAIN MENU”.
PORTUGUÊS
DTS SURROUND MODES
The following are further descriptions of DTS surround modes.
ITALIANO
DTS-HD MASTER AUDIO
DTS-HD Master Audio is a technology that delivers master audio sources
recorded in a professional studio to listeners without any loss of data,
preserving audio quality. DTS-HD Master Audio adopts variable data
transfer rates, facilitating data transfer to the maximum rate of 24.5 Mbps
in the Blu-ray disc format, 18.0 Mbps in the HD-DVD format, which by
far exceeds that of a standard DVD. These high data transfer rates enable
lossless transmission of 96 kHz/24-bit 7.1-channel audio sources without
deteriorating the quality of the original sound. DTS-HD Master Audio is an
irreplaceable technology that can reproduce sound faithfully as intended
by the creator of music or movies.
DEUTSCH
DTS-ES EXTENDED SURROUND (DTS ES)
This is a new multi-channel digital format which greatly improves the 360
degrees spatial sensation of the Surround impression thanks to the greater
space expansion of the surround signals, providing high compatibility with
the conventional DTS format.
NEDERLANDS
In addition to the 5.1 channels, the expanded DTS-ES Surround also
offers the back surround (also sometimes called the “surround centre”)
in reproduction, providing a total of 6.1 channels. The expanded DTS-ES
Surround includes two formats, with two different methods of surround
signal recording, as follows:
SVENSKA
DTS-ES DISCRETE 6.1
Since the signals of the 6.1 Surround channels (including the back channel)
are completely independent, it is possible to achieve the sensation that the
acoustic image is moving about freely among the background sounds, 360
degrees surrounding the listener.
РУССКИЙ
Although maximum quality is achieved with sound tracks recorded using
this system and reproduced using the DTS-ES decoder, when played with
a conventional DTS decoder, the back surround channel is automatically
downmixed in the surround right and surround left channels of the surround
system, in such a way that none of the signal components are lost.
24
When a DTS-ES decoder processes a discrete DTS-ES 6.1 or in Matrix 6.1,
these formats are automatically detected and the Optimum Surround
mode is selected. However, some DTS-ES Matrix 6.1 sources may be
detected as DTS. In this case the DTS-ES Matrix mode should be selected
manually in order to reproduce them.
DTS NEO: 6 SURROUND
This mode applies the conventional 2-channel signals such as digital PCM
or analog stereo signals to the high precision digital matrix decoder used
for DTS-ES Matrix 6.1 to achieve 6.1-channel surround playback. DTS Neo: 6
surround includes two modes for selecting the optimum decoding of the
signal sources:
DTS NEO: 6 CINEMA: This method is ideal for the reproduction of
movies. The decoding takes place by emphasizing the separation
in order to achieve the same atmosphere with 2-channel, as with
6.1-channel sources.
DTS NEO: 6 MUSIC: Mainly recommended for music reproduction. The
right and left front channels do not pass through the decoder and are
reproduced directly so there is no loss in sound quality, and the effects
of the right surround, left surround, central and back surround channels
add a natural sensation of expansion of the sound field.
ENHANCED STEREO
Please refer to the same description of ENHANCED STEREO under the
LISTENING MODES segment of the OPERATION - USING THE T 748 - MAIN
MENU.
OPERATION
ENGLISH
USING THE T 748 – SETUP MENU
A/V PRESETS SETUP
The Vacuum Fluorescent Display (VFD) and On-Screen Display (OSD) can be
shown in various ways by navigating through the parameters at the Display
Setup menu. Use a combination of [ A/S/D/F ] keys to step through the
Display Setup menu items.
The T 748’s simple but powerfully flexible system of “A/V Presets” allows you
to customize virtually every aspect of your audio-video playback, and recall
them with a single key-press. The parameters “Listening Mode”, “DSP Option”
and “Tone Controls” accessible via the “Main Menu” together with “Speaker
Setup” and “Display Setup” configurable through “Setup Menu” are stored
together as a single A/V Preset.
Now in order to save the settings chosen for the particular A/V Preset
number, scroll down to “Save Settings to Setup” and press the [ S ] key. If you
chose to load instead the default settings, scroll down to “Load Defaults to
Preset” and press the [ S ] key to restore the default settings.
In addition to the parameter settings, the A/V Preset label itself can be
assigned a new name. This new Name will be shown in the VFD as well as
on the OSD.
To rename the A/V Preset label, scroll to “Name” and press [ S ] to go the first
character. Then, press [ D/F ] to pick and select through the alphanumeric
selections. Press [ A/S] to move to the next character or back to the previous
character and at the same time save the changes done on the current
character. An A/V Preset can be renamed up to 8 characters.
NOTE
The selected A/V Preset remains in force until you select a different A/V
Preset.
PORTUGUÊS
ITALIANO
DEUTSCH
Scroll to “A/V Presets Setup” using the [ D/F ] keys to save a collection of
said parameter settings to a Preset. Select a Preset number and by pressing
the [ D/F ] keys, you can selectively include in the particular A/V Preset any
of the above-mentioned parameter settings by choosing “Yes”. If you decide
not to include in the particular A/V Preset a certain parameter setting, select
“No”.
NEDERLANDS
Temp Line: Choose between Line 1 and Line 2 as the desired line where
VFD will be temporarily shown if “Off” is selected at “Display” option as
described above.
CREATING PRESETS
Creating an A/V Preset consists simply of storing a complete set of the
parameters set forth in “Listening Mode”, “DSP Option” and “Tone Controls”
accessible via the “Main Menu” together with “Speaker Setup” and “Display
Setup” configurable through “Setup Menu”.
SVENSKA
VACUUM FLUORESCENT DISPLAY (VFD)
Display: Select “On” to display all applicable data or characters at the VFD.
Nothing will be shown at VFD if “Off” is selected. At “Off” setting however,
whenever any of the front panel controls or their corresponding keys in the
remote control is activated, the appropriate VFD characters will be shown
temporarily and then fade away.
Dimmer: If it is desired to reduce the brightness of the VFD, set Dimmer to
“Dim”. Otherwise, select “Bright” to return to normal VFD brightness.
Line 1, Line 2: The VFD shows two main lines of data or characters. Line
2 is the line of data or characters located at the lower bottom of the VFD
while directly above it is Line 1. For both lines, one can select which display
could be shown by choosing through the following
Source: Shows the active Source.
Volume: Current Volume level is shown.
Listening Md: Selected Listening Mode is shown.
A. Src Format: Shows the active Source’s detected audio format.
Off: Select “Off” if it is desired not to show any data at the applicable
Line.
You might create one A/V Preset optimized for pop music and another for
classical. One more A/V Preset can be set up to recall each family member’s
favorite setting or one for fully cinematic home-theater playback and yet
another one for late-night movies, with each A/V Preset fine-tuned to a
particular scenario or preference.
РУССКИЙ
NOTE
The configurations set forth at “Display Setup” are carried over whenever
it is enabled during A/V Presets setting. Please see also the section below
about “AV Presets Setup”.
ESPAÑOL
FRANÇAIS
DISPLAY SETUP
25
OPERATION
USING THE T 748 – SETUP MENU
ENGLISH
SAMPLE PROCEDURE FOR SETTING UP A/V PRESETS
1 Setup first your preferred settings for the following options (access
them through their respective menu page).
Speaker Setup: from the Speaker Setup menu, go to “Speaker
Configuration” sub-menu and change “Subwoofer” from “On” to “Off”:
“Front” becomes “Large”
Listening Mode: Stereo
FRANÇAIS
ESPAÑOL
DSP Option: 5ms
PORTUGUÊS
2 With the above settings, scroll to “A/V Presets Setup” from the SETUP
MENU page. Use [ S ] to access “A/V Presets Setup” menu.
ITALIANO
Tone Controls: Tone Defeat: On
DEUTSCH
NEDERLANDS
3 At “A/V Presets” page, set “Preset: 1” to the following conditions as below.
Use [ D/F ] to select “Yes” or “No”. Then, press [ A ], [ F ] and [ S ] to exit a
line item and move on to the next setting.
Display Setup: Set “Line 2” to “Listening Mode”
SVENSKA
РУССКИЙ
26
OPERATION
Display Setup: Set “Line 2” to “Volume”
FRANÇAIS
While at “Save Settings to Setup” menu line, use [ S ] to save the above
settings to Preset 1. Below OSD will be shown, affirming that the above
settings are now saved to “Preset 1”.
ENGLISH
USING THE T 748 – SETUP MENU
ESPAÑOL
5 With the above settings, scroll to “A/V Presets Setup” from the SETUP
MENU page. Use [ S ] to access “A/V Presets Setup” menu.
PORTUGUÊS
4 Now, repeat again Step 1 above but this time with the following
settings
Listening Mode: PLIIx Music
6 At “A/V Presets Setup” page, set “Preset: 2” to the following conditions as
below. Use [ D/F ] to select “Yes” or “No”. Then, press [ A ], [ F ] and [ S ]
to exit a line item and move on to the next setting.
ITALIANO
When associated to a particular Source number, the above preset values
and settings allocated at “Preset 1” (preset settings as shown in the OSD
captures at Step 1) will be recalled and applied to said assigned source.
Tone Controls: Tone Defeat: Off
РУССКИЙ
Note that “Speaker Setup” is set to “No”. At this condition, there will be
no “Speaker Setup” settings that will be associated to “Preset 2”. The
“Speaker Setup” settings that will be applied to “Preset 2” will be the last
or current “Speaker Setup” settings which in this sample are the same
“Speaker Setup” settings shown above in Step 1.
SVENSKA
While at “Save Settings to Setup” menu line, use [ S ] to save the settings
above to “Preset 2”. When associated to a particular Source number, the
above preset values and settings allocated at “Preset 2” (preset settings
as shown in the OSD captures at Step 4) will be recalled and applied to
said assigned source.
NEDERLANDS
DEUTSCH
DSP Options: 0ms
27
OPERATION
USING THE T 748 – SETUP MENU
ENGLISH
7 You can setup up to 5 A/V Presets. These same A/V Presets can also
be associated/defaulted to each Source in the “Source Setup (Normal)”
window as below.
FRANÇAIS
ESPAÑOL
In the above example, “Preset 1” settings are allocated to Source 1.
Whenever Source 1 is accessed, the “Preset 1” settings will be applied to
Source 1.
PORTUGUÊS
ITALIANO
DEUTSCH
NEDERLANDS
SVENSKA
РУССКИЙ
28
OPERATION
ASSEMBLING THE LOOP ANTENNA
1 Rotate the outer frame of the antenna.
2 Insert the bottom edge of the outer frame into the groove on the stand.
3 Extend the antenna cord.
SELECTING A TUNER BAND
Press the [AM/FM/DB] button on the AVR 4 while at AMP or TUNER device
selector page. Each subsequent press will toggle you through AM, FM or
DAB band. Stop (release button) at your desired tuner band.
TUNING AM/FM STATIONS
Upon selecting AM or FM band, use TUNE [
] on the AVR 4 to
perform slow manual search; press and hold to automatically search.
The front panel [ a/s ] or AVR 4’s [ A/S ] buttons can also be used to tune
for stations.
1 Press [ A/S ] momentarily to step up or down between AM or FM
frequencies.
2 Press and hold [ A/S ] for more than 2 seconds to search up or down
- the T 748’s tuner will stop at the next sufficiently strong signal it
encounters.
3 Pressing the [ A/S ] during the search process will stop the search.
AUTOMATIC PRESET
Preset stations may also be programmed automatically for the entire FM (or
AM) band.
1 Toggle the [AM/FM/DB] button to select FM (or AM) band.
2 Press and hold the [MEMORY] button until the station frequency
indication begins to increase.
3 Release the button and note that the tuner will search the entire FM
(or AM) band, and stop briefly at each station that has acceptable
signal strength. The T 748 will automatically assign a preset number to
each station, and then search for the next station. Up to 30 of the best
received FM stations (or 30 AM stations) will be automatically stored.
DIRECT RECALL OF A PRESET NUMBER
You can directly recall a desired Preset number.
1 Toggle [ENTER] button to switch between “Preset” and “Tune” mode (see
the lower line of the VFD). Select “Preset” mode.
2 Using the numeric keys of the remote control, directly key-in your
desired Preset number. For example, to enter Preset 5, press “5”.
DELETING A STORED PRESET
You can empty a preset by deleting the stored information.
1 Select the preset number to be deleted.
2 While at the selected preset number, press the [DELETE] button.
3 The preset will then be deleted. “Delete” is briefly shown in lower line of
the VFD.
4 To clear all the Presets at the same time, repeat step 2 again but this
time do not release the [DELETE] button. Press and hold [DELETE]
button until the current Preset number shown in the VFD is
extinguished (P--). “Delete All” is briefly shown in lower line of the VFD.
All Presets are now deleted.
FRANÇAIS
ESPAÑOL
PORTUGUÊS
IMPORTANT NOTE
When using the AVR 4 to carry out AM/FM commands, ensure that the
DEVICE SELECTOR is set to “TUN”.
NOTE
If there is no more vacant Preset number, you can overwrite an existing
Preset number by pressing the [ D/F ] buttons to select the Preset
number you want to overwrite
ITALIANO
The supplied AM “loop” antenna will usually provide adequate reception.
However, an exterior AM antenna can be used to improve reception.
Consult an antenna professional for more information.
DEUTSCH
In areas of poor FM reception, an exterior FM antenna can improve
performance dramatically. If radio listening is important to you, consider
consulting an antenna installation professional to optimize your system.
NEDERLANDS
ABOUT ANTENNAS
Connect the supplied lead-type FM antenna to the FM antenna input.
Extend the lead. Experiment freely with your antenna placement and
orientation until you get the clearest sound and lowest background noise.
Fix the antenna in the desired position by using thumb tacks, push pins or
any suitable means.
STORING PRESETS (AM/FM)
The T 748 can store up to 30 FM and 30 AM stations for immediate recall.
1 To store a desired AM/FM station to a preset, first tune to the desired
frequency (see above), then press AVR 4’s [MEMORY] button. The VFD
will show the next available Preset number – for example, “Preset 4 Free”
in the lower line and on the upper right corner “P-4” with “4” blinking.
2 Press the [MEMORY] button again to store the desired frequency on
the Preset number shown. Your desired frequency is now stored in the
assigned preset.
3 Alternatively, an AM/FM station can be stored to a Preset number by
repeating step 1. Enter a Preset number in two ways
• Directly enter a number between 1 to 30 and then press [MEMORY]
button.
• Toggle [ d/f ] or [ D/F ] to step through the Preset numbers, stop
at desired number and then press [MEMORY].
SVENSKA
The T 748’s internal AM/FM tuner offers very high quality sound from radio
broadcasts. The reception and sound quality will always be dependent to a
degree however on the type of antenna(s) used as well as proximity to the
broadcast origin, geography and weather conditions.
ENGLISH
LISTENING TO AM/FM RADIO
РУССКИЙ
DIRECT TUNING
If you know your desired station’s frequency allocation, you can tune
directly to the station.
1 Toggle [ENTER] button to switch between “Preset” and “Tune” mode (see
the lower line of the VFD). Select “Tune” mode.
2 Using the numeric keys of the remote control, key-in the frequency
allocation of the station. For example, to enter 104.50MHz, press “1”, “0”,
“4”, “5” and “0”.
29
OPERATION
LISTENING TO AM/FM RADIO
ENGLISH
CHOOSING THE TUNER MODE
The AVR 4’s [TUNER MODE] key is a dual-purpose control. Toggle [TUNER
MODE] to switch between “FM STEREO ON” and “FM STEREO OFF”. In the
normal position, “FM STEREO ON”, only the stations with a strong signal can
be listened to, and the noise between stations is muted.
FRANÇAIS
Pressing the [TUNER MODE] button again (“FM STEREO OFF”) allows distant
and potentially noisy stations to be received. Noise is reduced if the FM
station signal level is less than the FM Stereo threshold (since mono FM is
inherently less noise-prone) though at the sacrifice of the stereo effect.
ABOUT USER NAMES
ESPAÑOL
A particular Preset number can be assigned an eight-character “User
Name”. The assigned “User Name” will be shown in the VFD whenever the
associated Preset number is recalled.
PORTUGUÊS
ENTERING USER NAMES
To assign a Preset number with the user name “NEWS”, follow the procedure
as below.
1 Recall the desired Preset number.
2 Then, press and hold [INFO] of the AVR 4 until the display shows a
flashing cursor point.
3 Use the [ D/F ] buttons to select the first character of the name (“N”
from the alphabetical list).
4 Press [ S ] button to select the character and correspondingly move
forward to the next position. (Press [ A ] to go back to the previous
character). Repeat this process for each character in sequence.
5 Press the [INFO] key to store the User Name and exit the text-entry
mode.
ITALIANO
ABOUT RDS
DEUTSCH
The Radio Data System (RDS) permits sending small amounts of digital
information using conventional FM radio broadcasts. The T 748 supports
two RDS modes, program-service name (PS mode) and radio-text (RT
mode). Not every FM station incorporates RDS in its broadcast signal. In
most areas you will find from one to several RDS-enabled stations, but it is
by no means impossible that your favorite stations will not be broadcasting
RDS data.
VIEW RDS TEXT
When an RDS-enabled FM broadcast is tuned, the readout’s character
section will show its program-service name (PS) text.
NEDERLANDS
FM��107.10M��P06
NAD�������������
Press the AVR 4’s [INFO] button to toggle the readout between this and the
station’s radio-text (RT) readout, if any, which might scroll song- or artistname, or any other text of the station’s choosing.
SVENSKA
РУССКИЙ
30
OPERATION
CONNECTING THE DAB MODULE
Plug-in the other end of the DIN connector (supplied with your NAD DAB
Adaptor) from the DAB module’s output port into the corresponding DAB
module input socket on the rear panel of the T 748. Select DAB mode on
the T 748 by toggling the [AM/FM/DB] button in the AVR 4 remote control.
NOTES
• The NAD DAB Adaptor (DB 1 or DB 2) is not supplied with your T 748.
• Refer to the installation diagram printed on the carton box of the NAD
DAB Adaptor for guidance on how to connect the NAD DAB Adaptor to
the T 748.
• If there is no NAD DAB Adaptor connected, the VFD will show “Check
DAB Tuner”.
FRANÇAIS
ESPAÑOL
DAB�������������
oooooooooooooooo
“No Service List” will be shown in the VFD when no DAB stations are
found after the scanning process. If this occurs, check the connection
and position of the DAB antenna or call your local DAB broadcast
providers for coverage information.
DAB�������������
No�Service�List�
SERVICE LIST
Follow the steps below to select through the DAB service stations found.
1 At DAB mode, press [ A/S ] to step through the list of available stations
as shown in the lower display line of the VFD.
DAB�������������
<EDGE�102������>
PORTUGUÊS
2 The strength of the incoming signal can be shown on the VFD by
pressing the [ENTER] button. The more “o” segments visible in the lower
display line, the stronger the signal. By changing the position of the
antenna, you can increase the signal strength. Consult an antenna
professional for more information.
ITALIANO
NOTES
• When using the AVR 4 remote control to carry out DAB commands,
ensure that the DEVICE SELECTOR is set to “TUN”.
• At DAB mode and with DEVICE SELECTOR set to “TUN”, AVR 4’s [TUNER
MODE] button has the same function as that of front panel’s [MENU]
button.
• In the DAB discussions below, all control buttons mentioned are with
reference to the AVR 4 remote control.
The arrows show the progress of the sequence. When scanning is
completed, the last number shown on the upper right side of the VFD
corresponds to the total number of DAB broadcast stations found. Then,
the first station is tuned in (See “ALPHANUMERIC” description below to
understand the order or arrangement of stations).
DEUTSCH
IMPORTANT NOTICE
Unless otherwise specifically stated, navigating or accessing DAB
functions can be undertaken by using either the AVR 4 remote control
or the front panel buttons. If the control button or icon button being
referred to is available on the AVR 4 remote control and front panel,
then the reference to said button is applicable to both the AVR 4 remote
control and front panel.
Full scan������5
>>>>>>>>>>>>>>>>
NEDERLANDS
The T 748 makes it possible for you to enjoy listening to DAB broadcasts.
The T 748 has a Digital Audio Broadcast (DAB) module socket on the rear
panel for adding a separately sold and NAD-specified outboard DAB
module – the NAD DAB Adaptor DB 1 or the DAB+ NAD DAB Adaptor
DB 2. All the control software for this format is included; just plug-in the
module and start enjoying the CD-like quality sound and expansive content
selection available with DAB.
�DAB�Initialize�
�Please�wait��
SVENSKA
With DAB, the listener can scroll through a list of available stations - then
instantly tune to the station of his choice. There is no need either to
remember channel frequencies. All broadcasts are selected by simply
selecting the service name.
DAB OPERATION
With the separately sold NAD DAB Adaptor already connected to the T 748,
you can now carry out the T 748 to receive DAB broadcasts.
1 Toggle [AM/FM/DB] button until DAB mode. When DAB mode is
selected, VFD will show “DAB Initialize Please wait” and then go to “Full
scan” mode. “Full Scan” will take at least 20 seconds or more to complete.
FULL SCAN will enable the scanning of the full range of digital
frequencies (Band III and L-Band). This sequence cannot be interrupted.
2 Press [ENTER] to select the desired station.
РУССКИЙ
Until now, analogue radio signals such as FM or AM have been subject to
numerous kinds of interference on their way from the transmitter to your
radio. These problems were caused by mountains, high-rise buildings
and weather conditions. With Digital Audio Broadcast (DAB), you can now
receive CD-like quality radio programs without any annoying interference
and signal distortion. DAB broadcasts use digital signals rather than
traditional analogue transmissions, thus providing clear high quality
reception. You get far more robust reception and virtually hiss or crackle
free sound with DAB as long as you are within a good coverage area.
ENGLISH
LISTENING TO DAB RADIO
31
OPERATION
LISTENING TO DAB RADIO
ENGLISH
DAB TUNER MODE
FRANÇAIS
Aside from “Full scan” as already described above, pressing [TUNER MODE]
will also present you with other options namely - Local scan, Station order,
Dynamic range, Manual tune, Prune list and DAB reset. Use [ A/S ] to step
through these options.
ENSEMBLE
Digital radio is broadcast as groups of data called ensemble. Each ensemble
contains a number of stations, transmitted at a set frequency. When
“Ensemble” is selected as the mode of station order, the radio stations are
arranged in the order of their ensemble names.
An asterisk (*) to the right of a menu option indicates that it is the currently
selected option for a particular DAB menu. For example, <Favourites *> means
“Favourites” is the selected sequence for the DAB menu “Station order”.
NOTE
Ensemble is also interchangeably termed as “multiplex” by other
broadcast providers.
DAB�������������
<Favourites���*>
ESPAÑOL
LOCAL SCAN
PORTUGUÊS
LOCAL SCAN performs local scanning of available DAB services in your area.
Check with your dealer or visit www.WorldDAB.org to check the applicable
digital transmission frequencies in your area.
1 While listening to a DAB broadcast, press [TUNER MODE] button and
then [ A/S ] to select “Local scan”. Press [ENTER].
DAB�������������
<Local�scan����>
ITALIANO
2 Local scan of available DAB services in your area will start. The arrows show
the progress of the sequence. When scanning is completed, the last number
shown on the right side of the VFD corresponds to the total number of DAB
broadcast stations found. Then, the first station is tuned in.
STATION ORDER
DEUTSCH
Use “Station order” to sort the sequence of the listed stations. There are four
orders – Alphanumeric, Active, Ensemble and Favourites.
1 While listening to a DAB broadcast, press [TUNER MODE] button and
then [ A/S ] to select “Station order”. Press [ENTER].
DAB�������������
<Station�order�>
FAVOURITES
The T 748 memorizes the top ten stations you listen as you tune in stations.
They will be listed at the top of the broadcast list.
DYNAMIC RANGE
The level of compression of stations can be set to eliminate the differences
in dynamic range or sound level between DAB broadcasts. Popular music
would normally be more compressed than classical music, resulting in
possible different audio levels when changing from one station to the
other. Setting the Dynamic Range to “D-range 0” means no compression,
“D-range 1/2” indicates medium compression and “D-range 1” shows
maximum compression. No compression is recommended, especially for
classical music.
1 While listening to a DAB broadcast, press [TUNER MODE] button and
then [ A/S ] to select “Dynamic range”. Press [ENTER].
DAB�������������
<Dynamic�range�>
2 The lower line display shows the current dynamic range setting (with an
asterisk). Toggle [ A/S ] to select through “D-range 0”, “D-range 1/2” and
“D-range 1”.
DAB�������������
<D-range�0����*>
3 Press [ENTER] to select desired dynamic range level.
NEDERLANDS
MANUAL TUNE
2 Toggle [ A/S ] to select through “Alphanumeric”, “Active”, “Ensemble” and
“Favourites”.
3 Press [ENTER] to select desired station order.
ALPHANUMERIC
This is the default setting. Stations are arranged by numbers first and then
alphabetically by letters.
SVENSKA
ACTIVE
Active stations are listed at the top of the broadcast list. DAB broadcasts
that are in the list but have no service in the area will be displayed last in
the broadcast list.
РУССКИЙ
32
This option allows you to manually tune to a desired DAB broadcast and
include it in the service list (if not yet available at the time). You can also
use MANUAL TUNE to assist you in positioning the DAB antenna for best
reception of the desired DAB broadcast.
1 While listening to a DAB broadcast, press [TUNER MODE] button and
then [ A/S ] to select “Manual tune”. Press [ENTER]. The current channel
and frequency are shown in the lower line of the VFD.
DAB�������������
<Manual�tune���>
OPERATION
• If the manually tuned channel and frequency are not available, “No
Service List” will be shown in VFD.
NOTE
The number of ensembles and stations that could be scanned will vary
depending upon your location.
PRUNE LIST
There maybe situations wherein certain stations become inactive. The
“Prune list” option enables the deletion of these inactive stations in the
service list.
1 While listening to a DAB broadcast, press [TUNER MODE] button and
then [ A/S ] to select “Prune list”.
DAB�������������
Preset�memory�01
FRANÇAIS
ESPAÑOL
ooooo�����������
�5A��174.928MHz�
SETTING DAB PRESETS
The T 748 can store as many as 40 DAB stations of your favorite DAB
broadcast for immediate recall.
1 To store a DAB preset, first tune the DAB broadcast, and then press the
AVR 4’s panel [MEMORY] button (DEVICE SELECTOR must be set “TUN”).
The VFD will show “Preset Memory --”; “--” is blinking waiting for a Preset
number to be assigned.
2 Enter a Preset number in two ways
- Directly enter a number between 1 to 40 and then press [MEMORY]
button.
- Toggle [ d/f ] or [ D/F ] to step through the Preset numbers, stop at
desired number and then press [MEMORY].
Your desired DAB broadcast is now stored in the assigned preset.
3 Press [ d/f ] or [ D/F ] to step up or down between presets. Stop at
desired Preset number. Note that Presets must have been previously
stored.
DELETING A DAB PRESET
The procedure for deleting a DAB preset or all DAB Presets is the same as
that of deleting AM/FM Presets.
ITALIANO
DAB�������������
<Prune�list����>
PORTUGUÊS
2 To select other channels, toggle [ A/S ] to step through the channel list.
Release [ A/S ] when you have arrived at your desired channel. Press
[ENTER] to tune the selected channel.
• Channel and frequency are shown in the lower line of the VFD.
The number of “o” display at the upper line of the VFD indicates
the signal strength level of the current channel. To improve the
reception of the selected channel, adjust or reposition the DAB
antenna until the best reception is indicated.
ENGLISH
LISTENING TO DAB RADIO
DEUTSCH
2 Press [ENTER]. Use [ A/S ] and then press [ENTER] to select between
“Cancel” or “OK? [SELECT]”. Any inactive stations (normally preceded by
a “?” mark) are automatically deleted when “OK? [SELECT]” is selected.
Otherwise, select “Cancel”.
DAB�������������
<OK?[SELECT]���>
NEDERLANDS
DAB RESET
The “DAB reset” option enables the re-initializing of the NAD DAB Adaptor
by going to Full Scan mode.
1 While listening to a DAB broadcast, press [TUNER MODE] button and
then [ A/S ] to select “DAB reset”. Press [ENTER].
SVENSKA
DAB�������������
<DAB�reset�����>
2 The T 748 will initiate “DAB reset” and immediately go on to “Full Scan”
mode thereby enabling the T 748 to re-scan again the full range of
available DAB broadcasts.
РУССКИЙ
IMPORTANT NOTICE
When “DAB reset” option is selected, all stored DAB presets will be
erased.
33
OPERATION
LISTENING TO DAB RADIO
ENGLISH
INFORMATION SETTINGS
While listening to a DAB broadcast, the type of information displayed in the
lower line of the VFD can be varied. Toggle AVR 4’s [INFO] button to step
through the following display options:
FRANÇAIS
Station Name £
^
DLS
^
Program Type
^
Ensemble Name
^
Time and Date
^
Audio Signal information
^
Channel and frequency
^
Signal Q
^
Software version
ESPAÑOL
PORTUGUÊS
STATION NAME
The name or identification of the DAB broadcast station is shown.
ITALIANO
DLS
Dynamic Label Segment (DLS) is the scrolling text supplied by the
broadcasting station. It may contain information on music titles or details
regarding the program or station.
PROGRAM TYPE
This is a description of the type of broadcast supplied by the station, such
as Pop, Rock, Drama and the likes.
DEUTSCH
ENSEMBLE NAME
Displays the name of the ensemble on which current service is found.
TIME AND DATE
The current time and date as supplied by the DAB station are displayed.
NEDERLANDS
AUDIO SIGNAL INFORMATION
Displays the bit rate and audio type (stereo, mono or joint stereo)
as transmitted by the DAB broadcast provider. These are set by the
broadcaster to suit the type and quality of material being transmitted.
CHANNEL AND FREQUENCY
The channel and frequency of the currently tuned DAB broadcast are
displayed.
SVENSKA
SIGNAL QUALITY
This displays the digital error rate (0 to 99) of the currently tuned channel the lower the figure, the better the quality of the received broadcast.
SOFTWARE VERSION
Show the version number of the installed software.
РУССКИЙ
34
OPERATION
Make sure that all the devices are unplugged before making the
connections.
1 Connect the NAD IPD’s DATA PORT to the corresponding “MP DOCK”
data port of the T 748.
2 Connect also the NAD IPD’s S-Video out and audio out to the T 748
AUDIO 2/S-VIDEO input (the default iPod source allocation in the T 748).
3 Dock your iPod player into the NAD IPD.
NAVIGATING THE IPOD PLAYER’S FUNCTIONS AND FEATURES
After linking together your iPod player, NAD IPD and the T 748, you can now
plug them IN to their applicable power sources.
1 With your T 748, iPod player and NAD IPD all at power ON state, select
SOURCE 5 (iPod) of your T 748. Your iPod player will show in its display
the NAD logo and below it “OK to disconnect.” On the other hand, the
T 748 VFD will show in the upper line “iPod Menu” and the lower line
“Playlists”. The lower line will vary depending on the current menu
selected. At the same time, the T 748 OSD will display the whole iPod
Menu selections like Playlists, Artist, Albums, Genres, Songs, Composers,
Audiobooks and Podcasts.
2 Navigate through the iPod menu selections using a combination of the
[ A/S/D/F ] buttons.
9/0
• During playback or PAUSE mode, press and hold [ 9/0 ] for fast
forward or backward scanning of current song. Release button to
resume normal playback.
• Press [ 0 ] to skip forward to the next song or [ 9 ] to skip back to
the previous song.
[ j ] PAUSE / [ 4 ] PLAY
• Press PAUSE [ j ] during playback to stop playback temporarily. Resume
play by pressing [ 4 ] (Play).
• Toggle [ 4 ] (Play) to alternately switch from PLAY to PAUSE mode and
vice-versa.
FRANÇAIS
ESPAÑOL
DISP
• During playback, toggle [DISP] key of AVR 4 to show in the T 748 VFD
upper line the Song title, Artist Name and Album title.
• If there is no information available, the display will show “Unknown
Song”, “Unknown Artist” or “Unknown Album” as applicable. Aside from
this information, the lower line will display the current title’s song
number allocation and time elapsed.
PORTUGUÊS
CONNECTING THE OPTIONAL NAD IPD AND
iPod PLAYER TO THE T 748
ENTER
Press [ENTER] to select an option or start playback.
ITALIANO
NOTES
• “NAD IPD Dock for iPod” (NAD IPD) currently has two versions - the NAD
IPD 1 and NAD IPD 2. These two NAD IPD models and later variants are
compatible with the T 748.
• NAD IPD and iPod player are not supplied with your T 748.
• iPod player functions, features and playback capabilities accessible
through T 748 may vary depending on your iPod player model.
• When using the AVR 4 to control the iPod functions, make sure that the
Device Selector is set to “MP.”
Note that other NAD IPD models, like the NAD IPD 2, have their own remote
controls. The controls below also apply to the corresponding buttons of the
remote controls of such applicable NAD IPD models.
DEUTSCH
You can control your iPod player using the assigned buttons in the T 748
front panel. And with the corresponding AVR 4 remote control function
keys, you can select the materials stored in your iPod for playback as well as
access many of its functions even from across the room. The optional NAD
IPD also charges your iPod player while it is connected to the T 748.
CONTROL FEATURES AND SETTINGS
The following control functions and settings are selectable or enabled
using the front panel and AVR 4 remote control buttons. Since the AVR 4
will be the primary controller in most cases, we will focus on remotecontrolled operations.
NEDERLANDS
The T 748 is equipped with a data port in the rear panel where an optional
“NAD IPD Dock for iPod” (NAD IPD) can be plugged in. With the NAD IPD
linking the T 748 with your own iPod player, you can enjoy listening to your
favorite tracks and playlists as well as view applicable still image and video
playback.
ENGLISH
LISTENING TO YOUR iPod PLAYER
РУССКИЙ
SVENSKA
NOTES
• To exit from the iPod Menu at Source 5 (iPod), press [ A ] bringing you to
“Menu Select” OSD. Follow the instructions as prompted.
• Source 5 is defaulted to iPod. For Source 5 (iPod) to be changed and
allocated for other inputs, go to “iPod Setup” menu under the “Source
Setup” menu. At “iPod Setup” menu, set “Enabled” to “No” – you can now
assign Source 5 with another input or setting as desired.
35
OPERATION
LISTENING TO YOUR iPod PLAYER
ENGLISH
FRANÇAIS
ESPAÑOL
NAD IPD 2
TO VIEW VIDEOS OR PHOTOS LOADED IN YOUR iPod
The NAD IPD 2 has its own remote control - the DR 1. DR 1 can be used
to control NAD IPD 2 only at “Simple Mode”. When using the DR 1 to
command your iPod player docked in the NAD IPD 2, you have to refer to
your iPod player’s own display screen to make full use of its feature; there is
no OSD at this condition
Videos or photos uploaded in your iPod can be viewed directly via the
T 748. The following are the steps
1 Make sure that the “TV Out” setting of your iPod’s Video Settings menu is
at “On” mode and appropriate “TV Signal” is chosen.
2 Video or photo file selections and playback procedures are managed
directly from your iPod player and not through the T 748. You must exit
completely from the T 748’s Setup Menu or Menu Select OSD for you
to be able to navigate through your iPod player’s video or photo menu
options. A more direct way is by going to the “iPod Setup” menu and set
“Enabled” to “No”.
3 With the NAD IPD’s S-VIDEO OUT and AUDIO OUT ports connected to
the T 748’s AUDIO 2/S-VIDEO input or to any other assignable input, you
can now directly enjoy via T 748 your video or photo file selections as
uploaded in your iPod. Make sure that you select the correct “Source
Number” of the T 748. Note that if “Enabled” from “iPod Setup” is set
to “No”, ensure that Source 5 is enabled and analog audio and video
settings are assigned to “A2” and “S1” respectively.
In addition to the above commands common to the DR 1, below are the
descriptions of the other DR 1 control buttons.
LIGHT
Press [LIGHT] to turn ON the backlight of your iPod player if it is at idle
mode.
MENU
Press [MENU] to return to previous option or menu selection
ENTER
Press [ENTER] to select an option or start playback.
PORTUGUÊS
m (REPEAT)
Toggle to initiate repeat mode as follows - repeat one song, repeat all songs
or cancel repeat mode.
, (RANDOM)
Toggle to initiate playback in random order. There are three random modes
- Shuffle Song, Shuffle Album or Shuffle Off.
ITALIANO
DEUTSCH
NEDERLANDS
SVENSKA
РУССКИЙ
36
NOTE
For other navigation functions, please refer to your iPod player’s owner’s
manual. Depending on the iPod player model, some other functions
maybe controlled using the applicable T 748 navigation controls.
iPod is a trademark of Apple, Inc., registered in the U.S. and other countries.
REFERENCE
CONDITION
No sound from all channels.
POSSIBLE CAUSES
• AC power unplugged.
ENGLISH
TROUBLESHOOTING
POSSIBLE SOLUTIONS
• Check AC cable connection and outlet.
• Power not switched on.
No sound from surround channels.
• Toggle [MUTE] button to deactivate Mute
function.
• Faulty/missing cables.
• Check cables.
• “Speaker Configuration” channel (s) set to “OFF”.
• Check “Speaker Configuration” menu.
• No surround listening mode is engaged.
• Select appropriate listening mode.
• Surround channels set to “OFF” on “Speaker
Configuration” menu.
• Correct “Speaker Configuration” or “Speaker
Levels” settings.
ESPAÑOL
No sound from some channels.
• Mute function is activated.
FRANÇAIS
• Outlet has no power.
No sound from Subwoofer.
• Subwoofer is off, not powered or improperly
connected.
• Power up subwoofer, check subwoofer’s AC
outlet or check connections.
• Subwoofer set to “OFF” on “Speaker
Configuration” menu.
• Correct “Speaker Configuration” or “Speaker
Levels” settings.
PORTUGUÊS
• Surround channels level set too low on “Speaker
Levels” menu.
• Subwoofer level set too low on “‘Speaker Levels”
menu.
No sound from Center channel.
• Source is a 2/0 (etc.). Dolby Digital or DTS
recording without center channel.
• Play a known 5.1-channel recording or select
Dolby Pro Logic IIx Music mode.
• Center set to “OFF” on “Speaker Configuration”
menu.
• Correct “Speaker Configuration” or “Speaker
Levels” settings.
Display shows “No Service List”.
• Check source component setup.
• Batteries are flat or incorrectly inserted.
• Check batteries.
• Infrared receiver (IR) window of T 748 or IR
transmitter of the remote control is obstructed.
• Check IR windows and ensure clear line-of-sight
from remote to T 748.
• T 748 front panel is in very bright sunlight or
ambient light.
• Reduce sunlight/room lighting.
• Station signal too weak.
• Check station tuning. Adjust or replace antenna.
• Station not transmitting RDS data.
• Tune to an RDS station that supports programservice name (PS mode) and radio-text mode
(RT).
• DAB antenna not connected properly.
• Check the connection and position of DAB
antenna.
• No DAB coverage in the area.
• Call your local DAB broadcast providers for
coverage information.
DEUTSCH
• Source component not configured for
multichannel digital output.
NEDERLANDS
No RDS information.
• Check connections.
SVENSKA
T 748 does not respond to remote
control commands.
• Source’s digital output is not connected to a
T 748 digital input.
РУССКИЙ
No Dolby Digital/DTS.
ITALIANO
• Center level set too low on “Speaker Levels”
menu.
37
REFERENCE
SPECIFICATIONS
ENGLISH
AMPLIFIER SECTION
FRANÇAIS
Power output Stereo Mode
IHF dynamic power; 8 ohms
IHF dynamic power; 4 ohms
Power output Surround Mode
Total harmonic distortion at rated power
IM distortion at rated power
Damping factor, 8 ohms Input sensitivity and impedance Frequency response
Signal/noise ratio
Signal/noise ratio
2 x 80 W (8 ohms within rated distortion)
2 x 110 W
2 x 160 W
7 x 40 W
<0.08 %
<0.08 %
>60
250 mV/47 kohms
±0.5 dB (ref. 1 kHz, 20 Hz – 20 kHz)
>100 dB (ref. rated power at 8 ohms, A-WTD)
>90 dB (ref. 1 W at 8 ohms, A-WTD)
TUNER SECTION
ESPAÑOL
PORTUGUÊS
ITALIANO
AM SECTION
Tuning range
Usable sensitivity
Signal/Noise ratio
Total Harmonic Distortion
Loop sensitivity 20dB S/N
520 kHz -1710 kHz (120 V version, 10 kHz steps)
522 kHz -1620 kHz (230 V version, 9 kHz steps)
60 dBu
40 dB
<1.5 %
60 dBu
FM SECTION
87.50 MHz - 108.00 MHz
<10 dBu
65 dB
60 dB
0.25 %
0.5 %
30 dB
0.5 %
Tuning range
Usable sensitivity, MONO
S/N Ratio MONO
S/N Ratio STEREO
Total Harmonic Distortion, MONO
Total Harmonic Distortion, STEREO
Channel Separation
RDS decode sensitivity
POWER CONSUMPTION
Idle power
Standby power
50 W
<0.5 W
DEUTSCH
PHYSICAL SPECIFICATIONS
Unit Dimensions (W x H x D) Net Weight
Shipping Weight 435 x 167 x 397 mm (Gross)
17 ¹/₈ x 6 ⁵/₈ x 12 ¹³/₁₆ inches
11.5 kg (25.3 lbs)
14.0 kg (30.8 lbs)
NEDERLANDS
* - Gross dimensions include feet, volume knob and extended speaker terminals.
Specifications are subject to change without notice. For updated documentation and features, please log onto www.NADelectronics.com for the latest
information about T 748.
SVENSKA
Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,226,616; 6,487,535; 7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S. and worldwide patents issued & pending. DTS-HD, the Symbol, &
DTS-HD and the Symbol together are registered trademarks & DTS-HD Master Audio is a trademark of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved.
Dolby and the double-D symbol are registered trademarks of Dolby Laboratories.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
РУССКИЙ
38
39
РУССКИЙ
SVENSKA
NEDERLANDS
DEUTSCH
ITALIANO
PORTUGUÊS
ESPAÑOL
FRANÇAIS
ENGLISH
www.NADelectronics.com
©2011 NAD ELECTRONICS INTERNATIONAL
A DIVISION OF LENBROOK INDUSTRIES LIMITED
All rights reserved. NAD and the NAD logo are trademarks of NAD Electronics International, a division of Lenbrook Industries Limited.
No part of this publication may be reproduced, stored or transmitted in any form without the written permission of NAD Electronics International.
T748_eng_OM_v09 - 06/11
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement